SM8580AM Real-time Clock IC with 4-bit Interface and Built-in Temperature Sensor OVERVIEW The SM8580AM is a real-time clock IC based on a 32.768kHz crystal oscillator, which features a 4-bit parallel interface for communication with an external microcontroller. It comprises second-counter to year-counter clock and calendar circuits that feature automatic leap-year adjustment up to year 2099, alarm and timer interrupt functions, clock counter change detect functions, ±30-second correction function, time error correction function, and built-in temperature sensor. The 4-bit parallel interface is compatible with general-purpose SRAM over a high-speed bus. FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ PINOUT High-speed bus 4-bit parallel interface Date, day, hour, minute, and second-counter presettable alarm interrupt 1/4096 seconds to 255 minutes presettable interval timer interrupt function 2 software-maskable alarm and timer interrupt outputs Clock counter change detect functions 4-digit western calendar display Automatic leap year correction up to year 2099 ±30-second adjust function −195 to +192ppm time error correction range Built-in temperature sensor (analog voltage output) 2.4 to 5.5V interface voltage range 1.6 to 5.5V clock voltage range 0.6µA/3V (typ) current consumption (Top view) CE0N 1 24 VDD FCON XT FOUT XTN VTEMP NC AIRQN NC TIRQN NC A0 CE1 A1 D0 A2 D1 A3 D2 D3 RDN VSS 12 13 WRN ORDERING INFORMATION 7.80 ± 0.30 (Unit: mm) + 0.1 5 0.15 − 0.0 10.05 ± 0.20 10.20 ± 0.30 0.36 ± 0.10 0.10 0.12 M 0.20 0.10 0.8 0 to 10 0.50 ± 0.20 1.90 24-pin SSOP 5.40 ± 0.20 SM8580AM PACKAGE DIMENSIONS 1.80 Package 0.10 ± 0.10 Device SEIKO NPC CORPORATION —1 SM8580AM BLOCK DIAGRAM Control line CG XT CD OSC Divider XTN Digital Trimming Controller Clock and Calendar Counter Alarm Register AIRQN TIRQN FOUT Interrupt Control Timer Register FOUT Control FOUT Register FCON Control Register A0 to A3 D0 to D3 WRN BUS Interface RDN Temperature Sensor CE0N CE1 VDD VSS VTEMP SEIKO NPC CORPORATION —2 SM8580AM PIN DESCRIPTION Function1 Number Name I/O 1 CE0N I Chip enable 0 input with built-in pull-up resistor. The SM8580AM can be accessed when CE0N is LOW and CE1 is HIGH. 2 FCON I FOUT output frequency select control input (when CE1 is HIGH). 32.768kHz fixed frequency output when FCON is LOW. Output frequency determined by bit FD when FCON is HIGH (when FE bit is 1). Note that a HIGH-level voltage should be applied to FCON to avoid unwanted 32.768kHz output during backup. 3 FOUT O Frequency set register, frequency output (CMOS output) 4 VTEMP O Temperature voltage output (analog output) 5 AIRQN O Alarm interrupt output (N-channel open-drain output) 6 TIRQN O Timer interrupt output (N-channel open-drain output) 7 A0 I 8 A1 I 9 A2 I 10 A3 I 11 RDN I Read strobe input. Data can be read from SM8580AM when RDN is LOW and WRN is HIGH. An error will occur if both RDN and WRN are simultaneously LOW. 12 VSS – Ground 13 WRN I Write strobe input. Data can be written to SM8580AM when RDN is HIGH and WRN is LOW. An error will occur if both RDN and WRN are simultaneously LOW. 14 D3 I/O 15 D2 I/O 16 D1 I/O 17 D0 I/O 18 CE1 I Chip enable 1 input with built-in pull-down resistor. The SM8580AM can be accessed when CE0N is LOW and CE1 is HIGH. FOUT is in output mode when CE1 is HIGH, regardless of the state of CE0N. FOUT is high impedance when CE1 is LOW. 19 NC – No connection 20 NC – No connection 21 NC – No connection 22 XTN O Oscillator output, with built-in oscillator capacitance CD 23 XT I Oscillator output, with built-in oscillator capacitance CG 24 VDD – Supply Address inputs. Connect to the microcontroller address bus. The selected register address is input on this bus when accessing the SM8580AM (positive logic). Data bus input/outputs. Connect to the microcontroller data bus. 1. Connect a 0.1µF capacitor between VDD and VSS. SEIKO NPC CORPORATION —3 SM8580AM FOUT Output and SM8580AM Access Relationship CE0N CE1 FCON FE bit FOUT output SM8580AM accessible HIGH LOW × × High impedance No LOW LOW × × High impedance No LOW 0 32.768kHz output No LOW 1 32.768kHz output No HIGH 0 High impedance No HIGH 1 FD bit select frequency output No LOW 0 32.768kHz output Yes LOW 1 32.768kHz output Yes HIGH 0 High impedance Yes HIGH 1 FD bit select frequency output Yes HIGH HIGH LOW HIGH SPECIFICATIONS Absolute Maximum Ratings VSS = 0V Parameter Symbol Supply voltage range VDD Input voltage range VIN Output voltage range Storage temperature range Condition All inputs, D0 to D3 VOUT1 TIRQN, AIRQN VOUT2 FOUT, D0 to D3, VTEMP Tstg Rating Unit −0.3 to 7.0 V VSS − 0.3 to VDD + 0.3 V VSS − 0.3 to 8.0 V VSS − 0.3 to VDD + 0.3 V −55 to 125 °C Rating Unit Recommended Operating Conditions VSS = 0V Parameter Symbol Condition Supply voltage range VDD 2.4 to 5.5 V Clock supply voltage range VCLK 1.6 to 5.5 V Operating temperature range Topr −40 to 85 °C SEIKO NPC CORPORATION —4 SM8580AM DC Electrical Characteristics VSS = 0V, VDD = 1.6 to 5.5V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Current consumption 1 IDD1 VDD = 5V Current consumption 2 IDD2 VDD = 3V Current consumption 3 IDD3 VDD = 5V Current consumption 4 IDD4 VDD = 3V Current consumption 5 IDD5 VDD = 5V Current consumption 6 IDD6 VDD = 3V Current consumption 7 IDD7 VDD = 5V Current consumption 8 IDD8 VDD = 3V HIGH-level input voltage 1 VIH1 LOW-level input voltage 1 VIL1 VDD = 4.5 to 5.5V, CE0N, FCON, RDN, WRN, A0 to A3, D0 to D3 HIGH-level input voltage 2 VIH2 LOW-level input voltage 2 VIL2 HIGH-level input voltage 3 VIH3 LOW-level input voltage 3 VIL3 Input leakage current ILEAK CE0N = VDD, CE1 = VSS, FCON = RDN = WRN = A0 to A3 = VDD or VSS Pull-up resistance 1 RUP1 VDD = 5V RUP2 VDD = 3V RDWN1 VDD = 5V Pull-down resistance 2 RDWN2 VDD = 3V Pull-down resistance 3 RDWN3 VDD = 5V RDWN4 VDD = 3V HIGH-level output voltage 1 VOH1 VDD = 5V HIGH-level output voltage 2 VOH2 VDD = 3V HIGH-level output voltage 3 VOH3 VDD = 3V LOW-level output voltage 1 VOL1 VDD = 5V LOW-level output voltage 2 VOL2 VDD = 3V LOW-level output voltage 3 VOL3 VDD = 3V LOW-level output voltage 4 VOL4 VDD = 5V VOL5 VDD = 3V Pull-up resistance 2 Pull-down resistance 1 Pull-down resistance 4 LOW-level output voltage 5 Output leakage current IOZ CE0N = RDN = WRN = VDD, A0 to A3 = D0 to D3 = VDD or VSS, CE1 = FCON = VSS, AIRQN = TIRQN = FOUT = VDD, VTEMP output OFF (TEMP bit = 0) Ta = 25°C, CE0N = RDN = WRN = VDD, A0 to A3 = D0 to D3 = VDD or VSS, CE1 = FCON = VSS, AIRQN = TIRQN = FOUT = VDD, VTEMP output ON (TEMP bit = 1) CE0N = CE1 = RDN = WRN = VDD, A0 to A3 = D0 to D3 = VSS, FCON = VSS, AIRQN = TIRQN = FOUT = VTEMP = Hi-Z, VTEMP output OFF (TEMP bit = 0), FOUT = 32kHz output, CL = 0pF CE0N = CE1 = RDN = WRN = VDD, A0 to A3 = D0 to D3 = VSS, FCON = VSS, AIRQN = TIRQN = FOUT = VTEMP = Hi-Z, VTEMP output OFF (TEMP bit = 0), FOUT = 32kHz output, CL = 30pF VDD = 2.4 to 3.6V, CE0N, FCON, RDN, WRN, A0 to A3, D0 to D3 VDD = 1.6 to 5.5V, CE1 CE0N = VSS CE1 = VDD Unit min typ max – 1.0 2.0 µA – 0.6 1.0 µA – 50 75 µA – 40 60 µA – 3.0 7.5 µA – 1.7 4.5 µA – 8.0 20 µA – 5.0 12 µA 2.2 – VDD + 0.3 V VSS − 0.3 – 0.8 V 0.8VDD – VDD + 0.3 V VSS − 0.3 – 0.2VDD V 0.8VDD – VDD + 0.3 V VSS − 0.3 – 0.2VDD V −0.5 – 0.5 µA 75 150 300 kΩ 150 300 600 kΩ 20 40 80 MΩ 42.5 85 170 MΩ 30 60 120 kΩ 55 110 220 kΩ 4.5 – 5.0 V 2.0 – 3.0 V 2.9 – 3.0 V 0 – 0.5 V 0 – 0.8 V 0 – 0.1 V 0 – 0.25 V 0 – 0.4 V −0.5 – 0.5 µA CE1 = 0.5V IOH = −1mA, D0 to D3, FOUT IOH = −100µA, D0 to D3, FOUT IOL = 1mA, D0 to D3, FOUT IOL = 100µA, D0 to D3, FOUT IOL = 1mA, AIRQN, TIRQN D0 to D3, AIRQN, TIRQN, FOUT, VOUT = VDD or VSS SEIKO NPC CORPORATION —5 SM8580AM Terminal Capacitance Characteristics Ta = 25°C, f = 1MHz Rating Parameter Symbol Condition Unit min typ max Address input capacitance CADD A0 to A3 – – 8 pF Data output capacitance CDATA D0 to D3 – – 15 pF Oscillator Characteristics Ta = 25°C, NPC’s standard crystal (CI = 30kΩ, CL = 10pF) unless otherwise noted. Rating Parameter Symbol Oscillator start time tSTA Oscillator stop voltage VSTO Condition VDD = 1.6 V Unit min typ max – – 3.0 s – – 1.5 V Frequency voltage characteristic f/V VDD = 1.6 to 5.5V −2 – +2 ppm/V Frequency accuracy εIC VDD = 3.0V −20 – +20 ppm Input capacitance CG VDD = 3.0V – 15 – pF Output capacitance CD VDD = 3.0V – 10 – pF AC Characteristics (1) VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter FOUT duty Oscillator failure detection time Symbol Duty tOSC Condition Unit min max min VDD = 5V ± 10% 40 – 60 % VDD = 3V ± 10% 40 – 60 % VDD = 5V ± 10% 10 – – ms VDD = 3V ± 10% 10 – – ms SEIKO NPC CORPORATION —6 SM8580AM AC Characteristics (2) VDD = 2.4 to 3.6V, VSS = 0V, Ta = −40 to 85°C, inputs VI = 0.5VDD, outputs VO = 0.5VDD, output load capacitance CL = 100pF (tACC, tACS, tARD) Rating Parameter Symbol Unit min max Read cycle time tRC 150 – ns Address access time tACC – 150 ns CE access time tACS – 150 ns RD access time tARD – 100 ns CE output set time tCLZ 5 – ns CE output floating tCHZ – 60 ns RD output set time tOLZ 5 – ns RD output floating tOHZ – 60 ns Output hold time tOH 10 – ns Write cycle time tWC 150 – ns Chip select time tCW 140 – ns Address valid to end-of-write tAW 140 – ns Address setup time tAS 0 – ns Address hold time tWR 0 – ns Write pulsewidth tWP 130 – ns Input data set time tDW 80 – ns Input data hold time tDH 0 – ns VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C, inputs VI = 0.5VDD, outputs VO = 0.5VDD, output load capacitance CL = 100pF (tACC, tACS, tARD) Rating Parameter Symbol Unit min max Read cycle time tRC 85 – ns Address access time tACC – 85 ns CE access time tACS – 85 ns RD access time tARD – 45 ns CE output set time tCLZ 3 – ns CE output floating tCHZ – 30 ns RD output set time tOLZ 3 – ns RD output floating tOHZ – 30 ns Output hold time tOH 5 – ns Write cycle time tWC 85 – ns Chip select time tCW 70 – ns Address valid to end-of-write tAW 70 – ns Address setup time tAS 0 – ns Address hold time tWR 0 – ns Write pulsewidth tWP 65 – ns Input data set time tDW 35 – ns Input data hold time tDH 0 – ns SEIKO NPC CORPORATION —7 SM8580AM Data read t RC A0 to A3 t ACC t ACS t OH CE0N t CLZ t CHZ t ACS CE1 t CLZ t CHZ t ARD RDN t OLZ t OHZ D0 to D3 Data write CE control t WC A0 to A3 t WR t AW t CW CE0N* t AS CE1 WRN t DW t DH D0 to D3 WR control t WC A0 to A3 t WR t AW CE0N t AS CE1 t WP WRN* t DW t DH D0 to D3 *: When writing data, CE0N or WRN should be held HIGH level while the address changes. SEIKO NPC CORPORATION —8 SM8580AM Temperature Sensor VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min max min Temperature sensor output voltage VOUT Ta = 25°C, VSS reference output voltage, VDD = 2.7 to 5.5V, VTEMP – 1.470 – V Output accuracy TACR Ta = 25°C – – ±5 °C Temperature sensitivity1 VSE –40°C ≤ Ta ≤ 85°C, VDD = 2.7 to 5.5V −7.3 −7.8 −8.3 mV/°C Linearity2 ∆NL –40°C ≤ Ta ≤ 85°C, VDD = 2.7 to 5.5V – – ±2.0 % Temperature detection range TOPR ∆NL ≤ ±2.0%, VDD = 2.7 to 5.5V −40 – 85 °C Output resistance3 RO Ta = 25°C, VDD = 2.7 to 5.5V, VTEMP – 1.0 3.0 kΩ Output load capacitance CL VDD = 2.7 to 5.5V – – 100 pF Output load resistance RL VDD = 2.7 to 5.5V 500 – – kΩ – – 200 µs Response time tRSP VDD = 3.0V, RL = 500kΩ, CL = 100pF 1. Temperature sensitivity VSE = (V(85°C) − V(−40°C) ) ÷ 125 [mV/°C] 2. Linearity ∆NL = a ÷ b × 100 [%], where a = maximum deviation between the measured value and the approximated value of VTEMP, and b = difference between the measured values at temperatures of −40 and 85°C VTEMP(V) a V (−40 C) a b Measured value Approximate value a −40 C 0C 85 C V (85 C) Ta 3. Output resistance RO = ∆V1 ÷ ∆I1 [Ω] SM8580A VTEMP 1MΩ I1 OP AMP V1 SEIKO NPC CORPORATION —9 SM8580AM Backup Transfer and Return Rating Parameter1 Symbol Supply voltage falling edge CE setup time tCD Supply voltage fall time tF Condition Unit min max min 0 – – µs (VDD − VCLK) ≤ 2.0V 2 – – µs/V (VDD − VCLK) > 2.0V 50 – – µs/V Supply voltage rise time tR 1 – – µs/V Supply voltage rising edge CE hold time tCU 0 – – µs 1. Before switching the supply, confirm that the chip enable CE1 is LOW and that SM8580AM is deselected. VDD VCLK tF tCD CE1 tR tCU VIL VIL Backup mode SEIKO NPC CORPORATION —10 SM8580AM FUNCTIONAL DESCRIPTION Register Tables Bank 0 (clock, calendar registers) Address Register Bank 2 (digital correction, timer registers) Bit 3 Bit 2 Bit 1 Bit 0 Address Register Bit 3 Bit 2 Bit 1 Bit 0 8 4 2 1 0 DT3 DT2 DT1 DT0 FOS 40 20 10 1 Digital correction registers DT_ON DT6 DT5 DT4 8 4 2 1 2 – # # # # # 40 20 10 3 – # # # # 8 4 2 1 4 8 4 2 1 # # 20 10 5 Timer counter set registers 128 64 32 16 # 4 2 1 8 4 2 1 8 # # 20 10 9 8 4 2 1 A # # # 10 B 8 4 2 1 C 80 40 20 10 D 800 400 200 100 E TEST TEMP 2000 1000 Bank SEL1 Bank SEL0 STOP BUSY/ ADJ 0 Second registers 1 2 Minute registers 3 4 Hour registers 5 6 Day of week register 7 Date registers Month registers Year registers F Control register ■ Bank 1 (alarm, FOUT registers) Address Register 0 Bit 3 Bit 2 Bit 1 Bit 0 8 4 2 1 AE 40 20 10 8 4 2 1 AE 40 20 10 8 4 2 1 AE * 20 10 AE 4 2 1 8 4 2 1 AE * 20 10 Second registers 1 2 ■ ■ ■ Minute registers 3 4 Hour registers 5 6 Day of week register 7 ■ ■ ■ Date registers 8 ■ 9 – * * * * A – * * * * B CE1 control * * C FOUT divider set register # FD2 FD1 FD0 ■ D FOUT frequency set register FE # FD4 FD3 ■ E Alarm control TEST TEMP AF AIE F Control register Bank SEL1 Bank SEL0 STOP BUSY/ ADJ CTEMP CDT_ON 8 4 2 1 7 Timer counter output registers 128 64 32 16 8 Timer setting TE TI/TP TD1 TD0 9 – # # # # A – # # # # B – * * * * C – * * * * D – * * * * E Timer control TEST TEMP TF TIE F Control register Bank SEL1 Bank SEL0 STOP BUSY/ ADJ 6 All bits in register F and bits 2 to 3 in register E are common to all register banks. When alarm interrupts are not used, registers 0 to 8 in bank 1 can be used as RAM (total 36 bits). When timer interrupts are not used, registers 4 to 5 in bank 2 can be used as RAM (total 8 bits). When digital correction is not used, registers 0 to 1 in bank 2 can be used as RAM, excluding bit 3 (DT_ON) in register 1 (total 7 bits). The BUSY/ADJ bit function is BUSY when reading, and ADJ when writing. The BUSY flag is set to 1 an interval of 244µs before clock counter update timing. Registers 6 and 7 in bank 2 are read-only registers, and cannot be written to. When power is applied, all register bits are undefined, with the exception of bits FOS, TEST and TEMP. Accordingly, these bits need to be initialized. TEST and TEMP are automatically reset to 0 and FOS is automatically reset to 1 when power is applied. Bits marked # are all read-only bits fixed to 0. These bits cannot be written to. Bits marked * can be used as RAM bits. SEIKO NPC CORPORATION —11 SM8580AM Control Registers (All Banks, Register E (bits 2, 3) and F) Bank Address Bit 3 Bit 2 E TEST TEMP F Bank SEL1 Bank SEL0 Bit 1 Bit 0 STOP BUSY/ADJ 0, 1, 2 ■ ■ ■ ■ ■ TEST bit Factory test bit. This bit should be set to 0. Take care when writing to other E register bits not to accidentally write 1 to the TEST bit. Automatically resets to 0 when power (VDD) is applied. TEMP bit When set to 1, it enables the temperature sensor voltage output on pin VTEMP. When set to 0, VTEMP is high impedance. Automatically resets to 0 when power is applied. Bank SEL bits Bank select bits for read/write operations. Bank SEL1 Bank SEL0 Accessed bank 0 0 Bank 0 0 1 Bank 1 1 0 Bank 2 1 1 Bank 1 STOP bit When set to 1, the clock 32Hz frequency divider counter stops and is reset. When set to 0, the clock restarts. BUSY/ADJ bit This bit functions as a BUSY function in read mode, and as an ADJ function in write mode. • ADJ function (±30 seconds adjust bit) The following processes are operated when a logic 1 is written to ADJ, however a logic 0 cannot be written to. Second registers are reset to 00 and minute registers not incremented when the clock counter is reset and the second registers are currently 00 to 29. Second registers are reset to 00 and minute registers are incremented when the clock counter is reset and the second registers are currently 30 to 59. The ADJ bit is automatically reset to 0 a maximum of 244µs after it is set to 1. • BUSY function (second registers increment or ±30 seconds adjust busy indicator bit) When BUSY is 1, the counters are being updated (incremented or reset). To read or write to clock and calendar registers, the BUSY flag has to be 0. If reading data when BUSY is set to 1, there is a possibility that incorrect (intermediate) data will be output. BUSY is set to 1 under the following two circumstances. Normal seconds digit carry ±30 seconds digit adjust (when ADJ is set to 1) max 244µs 244µs Carry complete Setting ADJ bit to "1" Adjust function complete SEIKO NPC CORPORATION —12 SM8580AM ■ Function operation table Bit STOP Function ADJ Clock Timer Alarm FOUT Operating Operating7 0 0 Operating Operating3 0 1 Adjust1 Operating4 Operating6 Operating8 1 0 Stopped Operating/stopped5 Stopped Operating/stopped9 1 1 Stopped/adjust2 Operating/stopped5 Stopped Operating/stopped9 1. ±30 seconds adjust function 2. The clock stops, and the ±30 seconds adjust function operates. 3. If the timer source clock frequency is ≤ 1Hz, the timer cycle changes when the digital correction function is used. If the timer source clock frequency is ≥ 64Hz, the timer cycle is not affected when the digital correction function is used. 4. If the timer source clock frequency is ≤ 1Hz, the timer cycle changes. If the timer source clock frequency is ≥ 64Hz, the timer cycle does not change. 5. If the timer source clock frequency is ≤ 1Hz, the timer is stopped. If the timer source clock frequency is ≥ 64Hz, the timer operates. 6. An alarm interrupt is not generated by the 30-second adjust function (ADJ) even if all other alarm conditions are met. However, an alarm interrupt is generated 1 second later if the alarm conditions are still met. 7. If the FOUT source clock frequency is ≤ 1Hz, the cycle changes when the digital correction function is used. If the FOUT source clock frequency is ≥ 32Hz, the cycle is not affected when the digital correction function is used. 8. If the FOUT source clock frequency is ≤ 1Hz, the cycle changes. If the FOUT source clock frequency is ≥ 32Hz, the cycle does not change. 9. If the FOUT source clock frequency is ≤ 1Hz, the timer is stopped. If the FOUT source clock frequency is ≥ 32Hz, the timer operates. SEIKO NPC CORPORATION —13 SM8580AM Clock and Calendar Registers (Bank 0, Registers 0 to E) Clock counters (registers 0 to 5) Bank Address Register 0 Bit 3 Bit 2 Bit 1 Bit 0 8 4 2 1 FOS 40 20 10 8 4 2 1 40 20 10 4 2 1 20 10 Second registers 1 2 0 Minute registers 3 4 8 Hour registers 5 ■ ■ Data in these registers is interpreted in BCD format. For example, if the seconds registers 1 and 0 contain 0101 1001, then the contents are interpreted as the value 59 seconds. Hour register contents are values expressed in 24-hour mode. FOS (oscillator failed detect bit (register 1, bit 3)) ■ The FOS bit is the oscillator failure flag. It indicates that the oscillator has stopped due to supply voltage reduction during operation. It is set to 1 when the oscillator stops, and remains 1 until reset by writing 0 to FOS. It is not affected by the function of other bits. A 1 is written to FOS when power is applied. Day-of-week counter (register 6) ■ Bank Address Register 0 6 Day of week register Bit 3 Bit 2 Bit 1 Bit 0 4 2 1 The day-of-week register contains values representing the day of the week as shown in the following table. Bit 2 Bit 1 Bit 0 Weekday 0 0 0 Sunday 0 0 1 Monday 0 1 0 Tuesday 0 1 1 Wednesday 1 0 0 Thursday 1 0 1 Friday 1 1 0 Saturday Calendar registers (registers 7 to E) Bank Address Register 7 Bit 3 Bit 2 8 4 Bit 1 Bit 0 2 1 20 10 2 1 Date registers 8 9 8 4 Month registers A 10 0 B 8 4 2 1 80 40 20 10 D 800 400 200 100 E TEST TEMP 2000 1000 C Year registers ■ ■ Registers B to E are 4 digits forming the western calendar year. Leap-year adjustment is automatic for years 1901 to 2099. SEIKO NPC CORPORATION —14 SM8580AM Alarm Registers (Bank 1, Registers 0 to 8, E) Alarm control register (register E) ■ ■ Bank Address Register 1 E Alarm control Bit 3 Bit 2 Bit 1 Bit 0 AF AIE AF bit (alarm flag) The AF bit is set to 1 when an alarm event is occurred, when the settings in the alarm set registers (bank 1, registers 0 to 8) match the settings in the day, clock and calendar registers (bank 0, registers 0 to 8). A logic 0 cannot be written to AF for 1µs maximum after AF is set to 1. The AF bit remains 1 until reset by writing 0 to AF. A logic 1 cannot be written to AF. AIE bit (alarm interrupt enable) This bit enables the output on AIRQN when an alarm interrupt is occurred. If the AIE is not set to 1, then no output occurs even if the AF bit is set to 1. The AIRQN output is high impedance when AIE is set to 0. Alarm set registers (registers 0 to 8) Bank Address Register 0 Bit 3 Bit 2 Bit 1 Bit 0 8 4 2 1 AE 40 20 10 Second registers 1 2 8 4 2 1 AE 40 20 10 8 4 2 1 AE * 20 10 AE 4 2 1 8 4 2 1 AE * 20 10 Minute registers 3 1 4 Hour registers 5 6 Day of week register 7 Date registers 8 ■ ■ ■ ■ ■ These registers set the alarm time and date. When the corresponding bank 0 registers match these bank 1 registers, an alarm event occurs and AIRQN goes LOW if AIE is set to 1. An alarm can be set for date, day-of-week, hour, minute, and second. Each of these have a corresponding AE (alarm enable) bit which allows easy combination to create alarm events every second, every minute, hourly, daily, and weekly alarms. Note that alarms cannot be set for multiple days within the same week (such as an alarm on Mondays and Fridays only). When an AE bit is set to 0, the relevant register and corresponding bank 0 register are compared. When an AE bit is set to 1, the data is disregarded and all bits considered as “don’t care” bits. Day-of-week alarm bits (register 6) ■ The day-of-week register contains values representing the day of the week as shown in the following table. Bit 2 Bit 1 Bit 0 Weekday 0 0 0 Sunday 0 0 1 Monday 0 1 0 Tuesday 0 1 1 Wednesday 1 0 0 Thursday 1 0 1 Friday 1 1 0 Saturday SEIKO NPC CORPORATION —15 SM8580AM Timer Registers (Bank 2, Registers 4 to 8, E) Timer control registers (registers 8, E) Bank Address Register Bit 3 Bit 2 8 Timer setting TE TI/TP E Timer control Bit 1 Bit 0 TF TIE 2 ■ ■ ■ ■ TE bit (timer enable) Timer countdown stop/start control bit. When set to 1, the timer starts counting down. When set to 0 during countdown, the timer stops. TF bit (timer flag) The timer flag is set to 1 when the timer counter counts down to zero, occurring a timer event. A logic 0 cannot be written to TF for 1µs maximum after TF is set to 1. It is held at 1 until 0 is written to this bit. A 1 cannot be written to TF. TIE bit (timer interrupt enable) This bit enables the timer interrupt output on TIRQN when a timer event is occurred. If the TIE is not set to 1, then no output occurs even if the TF bit is set to 1. The TIRQN output is high impedance when TIE is set to 0. TI/TP bit (level/periodic interrupt mode select bit) Sets the timer interrupt signal output mode. The SM8580AM supports two timer function modes. • TI/TP = 0 (level interrupt mode) When a timer interrupt is occurred, TIRQN goes LOW (if TIE = 1) and TF is set to 1. TIRQN remains LOW and TF is held at 1 until a 0 is written to the TF bit. The timer operates by counting down until the data is zero, then the TE bit is cleared and the count stops automatically. However, if the timer is started when the TF bit is 1, then the TE bit is not cleared. The timer count register contents remain zero after the count down stops. • TI/TP = 1 (periodic interrupt mode) When a timer interrupt is occurred, TIRQN goes LOW (if TIE = 1) and TF is set to 1. TIRQN subsequently goes high impedance after a fixed interval, but TF is held at 1 until a 0 is written to the TF bit. The timer operates by counting down until the data is zero, then the timer register data is reloaded automatically after a fixed interval, and the countdown restarts. This mode can be used as a repetitive interval timer. Timer source clock set register (register 8) ■ Bank Address Register 2 8 Timer setting Bit 3 Bit 2 Bit 1 Bit 0 TD1 TD0 The register 8 bits 0 and 1 set the timer source clock to one of four frequencies listed in the following table. TD1 TD0 Timer source clock 0 0 4096Hz 0 1 64Hz 1 0 1Hz 1 1 1/60Hz (1 minute) SEIKO NPC CORPORATION —16 SM8580AM Timer counter set registers (registers 4 to 7) Bank Address Register 4 Bit 3 Bit 2 Bit 1 Bit 0 8 4 2 1 128 64 32 16 8 4 2 1 128 64 32 16 Timer counter set registers 5 2 6 Timer counter output registers 7 ■ ■ ■ ■ ■ Registers 4 and 5 set an 8-bit presettable binary down-counter value for the timer interrupt function. The value of the count can be determined by reading the values of registers 6 and 7 during the count. The presettable binary down-counter is updated when the data is written to registers 4 and 5. The data written to registers 4 and 5 are stored and are not changed until replacement data is written. This allows these bits to function as RAM bits if the timer interrupt mode is not used (when TIE = 0). When TE is set to 1, periodic interrupts are not output on TIRQN, even if registers 4 and 5 are set to zero. Timer interrupt function example Example of an hourly periodic timer interrupt Bank Address Register 4 Bit 3 Bit 2 Bit 1 Bit 0 1 1 0 0 0 0 1 1 Timer counter set registers 5 2 ■ ■ 8 Timer set register TE 1 1 1 E Timer control TEST TEMP TF 1 The timer error, when the timer starts, is an interval of 0 to 1 cycles of the source clock selected during the first timer operation. Specifically, if the source clock is 1/60Hz (1 minute cycle) and with TE bit = 1 write timing, the maximum error that can occur is +60 seconds. Also, timer operations that last less than 1 source clock cycle are not normally counted. The timer count start timing in data write mode occurs on the first falling edge of the source clock after the WRN rising edge that sets the TE bit, shown in the timing diagram below. Also, when the timer is stopped by changing the setting of TE bit from 1 to 0, the count stops after the countdown operation a maximum of 1 clock cycle of the selected source clock later. Specifically, if the source clock is 1/60Hz (1 minute cycle) and with TE bit = 0 write timing, the timer count is decremented and the timing stops a maximum of 60 seconds later. At this point, there is a possibility that the timer count has decremented to zero and generated an interrupt. Therefore, if interrupts are not required, the TIE interrupt enable bit should be set to avoid unwanted interrupts from occurring. Address 8 WRN pin D3 pin TE Timer source clock Timer TE="1" "0" Timer stop Timer start TE="0" "1" SEIKO NPC CORPORATION —17 SM8580AM CE1 Control Register (Bank 1, Register B) ■ ■ ■ ■ Bank Address Register Bit 3 Bit 2 1 B CE1 control CTEMP CDT_ON Bit 1 Bit 0 This register determines whether the temperature sensor function and digital correction function in combination with the CE1 input pin. CTEMP determines the temperature sensor operation, and CDT_ON determines the digital correction function operation. CTEMP bit When CTEMP is set to 0, the temperature sensor operates only when the CE1 pin is HIGH. When CTEMP is set to 1, the temperature sensor operates without any relationship to the CE1 input state. Note that the temperature sensor operation also depends on the bank 2 TEMP bit to be active. CDT_ON bit When CDT_ON is set to 0, the digital correction function operates only when the CE1 pin is HIGH. When CDT_ON is set to 1, the digital correction function operates without any relationship to the CE1 input state. Note that the digital correction function also depends on the bank 2 DT_ON bit to be active. Function operation tables CE1 pin CTEMP bit TEMP bit Temperature sensor × × 0 Not operating LOW 0 1 Not operating HIGH 0 1 Operating LOW 1 1 Operating HIGH 1 1 Operating CE1 pin CDT_ON bit DT_ON bit Digital correction × × 0 Not operating LOW 0 1 Not operating HIGH 0 1 Operating LOW 1 1 Operating HIGH 1 1 Operating SEIKO NPC CORPORATION —18 SM8580AM Frequency Set Registers (Bank 1, Registers C, D) Bank Address Register Bit 3 C FOUT divider set register D FOUT frequency set register Bit 2 Bit 1 Bit 0 FD2 FD1 FD0 FD4 FD3 1 ■ ■ ■ FE FD3, FD4 bit FOUT source clock frequency set bits. FD4 FD3 Source clock 0 0 32768Hz 0 1 1024Hz 1 0 32Hz 1 1 1Hz FD0 to FD2 bits Frequency divider set bits for the FOUT source clock set by FD3 and FD4. FD2 FD1 FD0 Frequency divider ratio FOUT output duty 0 0 0 1/1 1/2 0 0 1 1/2 1/2 0 1 0 1/3 1/3 0 1 1 1/6 1/2 1 0 0 1/5 1/5 1 0 1 1/10 1/2 1 1 0 1/15 1/3 1 1 1 1/30 1/2 FE bit FOUT frequency signal set by FD0 to FD4 output enable bit. When FCON is HIGH and FE is set to 1, then the frequency signal set by FD0 to FD4 is output on FOUT. When FE is set to 0, the FOUT output is high impedance. When FCON is LOW, a standard 32.768kHz signal is output on FOUT without reference to the settings in the C and D registers. SEIKO NPC CORPORATION —19 SM8580AM Digital Correction Registers (Bank 2, Registers 0, 1) Bank Address Register 0 2 ■ ■ ■ Bit 2 Bit 1 Bit 0 DT3 DT2 DT1 DT0 DT_ON DT6 DT5 DT4 Digital correction registers 1 ■ Bit 3 These registers enable and set the level of digital correction applied to oscillator clock. DT_ON enables the correction function, and bits DT0 to DT6 set the level of correction to be applied. This function adjusts the number of 1 second cycles which occur every 10 seconds. When digital correction is not used, a 0 should be written to DT_ON to disable correction. Correction range and resolution (correction range depends on the frequency) Correction range Correction resolution Correction cycle −195.20 to +192.15ppm 3.05ppm 10 seconds DT bits and digital correction (correction value depends on the frequency) Digital correction bits Correction (ppm) DT6 DT5 DT4 DT3 DT2 DT1 DT0 0 1 1 1 1 1 1 +192.15 0 1 1 1 1 1 0 +189.10 ↓ ↓ 0 0 0 0 0 1 0 +6.10 0 0 0 0 0 0 1 +3.05 0 0 0 0 0 0 0 ±0.00 1 1 1 1 1 1 1 −3.05 1 1 1 1 1 1 0 −6.10 ↓ ■ ↓ 1 0 0 0 0 0 1 −192.15 1 0 0 0 0 0 0 −195.20 Correction value calculation • Positive correction (leading time) [DT6:0] = correction ÷ 3.05 (with decimal round-off) Example: for correction of 192.15ppm [DT6:0] = 192.15 ÷ 3.05 = 6310 = 01111112 • Negative correction (lagging time) [DT6:0] = 128 + correction ÷ 3.05 (with decimal round-off) Example: for correction of −158.6ppm [DT6:0] = 128 + (−158.6 ÷ 3.05) = 7610 = 10011002 SEIKO NPC CORPORATION —20 SM8580AM INTERRUPT OPERATION Alarm Interrupt When AIE is 1 and an alarm event occurs (AF bit is set to 1), AIRQN output goes LOW. If AIE is 0, however, AIRQN is in a high-impedance state. The alarm interrupt is output when a carry from the seconds register to the minute register occurs. "1" "1" "1" AIE bit "0" "0" *No output while AIE bit is "0". Hi-Z AIRQN pin "L" level "1" AF bit "0" Interrupt is active. Setting AF bit to "0". Timer Interrupt The timer interrupt mode (level interrupt or periodic interrupt) is selected by the setting of TI/TP. Level interrupt mode (TI/TP = 0) When TIE is 1 and a timer interrupt event occurs (TF bit is set to 1), TIRQN goes LOW. When TIE is 0, however, TIRQN is in a high-impedance state. "1" "1" "1" TIE bit "0" "0" *No output while TIE bit is "0". Hi-Z TIRQN pin "L" level "1" TF bit "0" Interrupt is active. Setting TF bit to "0". SEIKO NPC CORPORATION —21 SM8580AM Periodic interrupt mode (TI/TP = 1) When TIE is 1 and a timer interrupt event occurs (TF bit is set to 1), TIRQN goes LOW. If TIE is 0, however, TIRQN is in a high-impedance state, and the TF bit remains set to 1. "1" TIE bit "0" tRTN Hi-Z TIRQN pin "L" level Auto-return "1" TF bit "0" Interrupt is active. Setting TF bit to "0". The auto-return time (tRTN), shown in the following figure and table, is determined by the source clock frequency set by register 8 in bank 2 bits TD0 and TD1. Source CLK Hi-Z TIRQN pin "0" Auto return time (tRTN) Interrupt cycle TD1 TD0 Source clock Auto-return time (tRTN) 0 0 4096Hz 0.122ms 0 1 64Hz 7.81ms 1 0 1Hz 7.81ms 1 1 1/60Hz 7.81ms SEIKO NPC CORPORATION —22 SM8580AM APPLICATION NOTES Setting the Alarm Alarms can be set for day, weekday, hour, minute, and second. However, it is not possible to set an alarm for more than one weekday. Note that it is recommended that AF and AIE be set to 0 at the same time to avoid accidental hardware interrupts while setting the alarm. After the alarm data is entered, initialization occurs when AF is again set to 0. If the interrupt output is not used by setting AIE set to 0, an alarm can still be controlled by software monitoring of the AF bit. Example 1 To set an alarm for 6pm of the following day: • Set bits AIE and AF to 0. • Set the day register AE bit to 1. • Acquire the current weekday setting from bank 0 register 6, add 1 to the current value (except in the case of Saturday), and write the updated data. Note that the day following 6H (Saturday) is 0H (Sunday). • Write 18H to the hour alarm register. • Write 00H to the minute alarm register. • Write 00H to the seconds alarm register. • Set bit AF to 0. • Set bit AIE to 1. Example 2 To set an alarm for 6am on every for Sunday: • • • • • • • • Set bits AIE and AF to 0. Set the day alarm register AE bit to 1. Write 0H to the weekday alarm register. Write 06H to the hour alarm register. Write 00H to the minute alarm register. Write 00H to the seconds alarm register. Set bit AF to 0. Set bit AIE to 1. Using the Temperature Sensor The SM8580AM temperature sensor can be used to monitor the surrounding temperature. The temperature sensor information can then be used to adjust the clock for any temperature variations in the oscillator frequency which affect the accuracy of the clock. One method of utilizing the temperature sensor to adjust timing errors is by using the clock error correction function (digital correction), as described below. 1. Based on the known temperature characteristics of the oscillator crystal, store temperature correction values for various temperatures in an external non-volatile EEPROM. 2. Use an A/D converter, such as in a general-purpose CPU, to convert the VTEMP temperature sensor output voltage into a digital value. 3. Use the digital value of the current temperature to access the temperature correction data stored in the EEPROM, and then write the corresponding data into the digital correction registers. This procedure is useful in implementing a high-accuracy clock function. SEIKO NPC CORPORATION —23 SM8580AM Monitoring Digital Correction Using the test mode allows the 64Hz digital correction clock to be output on pin FOUT. The test mode works as follows. 1. 2. 3. 4. 5. 6. Apply a HIGH-level on FCON. Set the FOUT frequency set register FE bit to 1. Set the CE1 control register CDT_ON bit to 1. Set correction data in the digital correction register DT0 to DT6 bits, and then set DT_ON to 1. Set the bank 2 register C, bit 1 to 1. When CE0N is LOW and CE1 is HIGH and the test mode set register TEST bit is set to 1, the digital correction cycle changes from 10 seconds to 1/64 seconds, and the clock output on FOUT is the 64Hz clock after timing correction. The output is the corrected timing for the set digital correction value corresponding to a 64Hz clock × 64[ppm]. Measuring this output provides a quick method for monitoring the digital correction function. 7. When CE0N goes HIGH, the TEST bit is reset to 1 and test mode is released. TYPICAL APPLICATION CIRCUIT VCC Schottky Barrier Diode FOUT VDD Voltage Detector VTEMP VCC AIRQN TIRQN XT CPU CE1 CE0N XTN FCON Address Decoder Upper Address A0 to A3 A0 to A3 D0 to D3 D0 to D3 RDN RDN WRN WRN VSS VSS SM8580AM Note. Because all the circuit components, except the crystal unit, are built in the SM8580AM chip, the oscillation circuit is realized just by the connection of the 32.768kHz crystal unit between XT and XTN terminals. The digital correction function is used to adjust the accuracy of clock time. SEIKO NPC CORPORATION —24 SM8580AM Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. SEIKO NPC CORPORATION 15-6, Nihombashi-kabutocho, Chuo-ku, Tokyo 103-0026, Japan Telephone: +81-3-6667-6601 Facsimile: +81-3-6667-6611 http://www.npc.co.jp/ Email: [email protected] NC9915FE 2006.06 SEIKO NPC CORPORATION —25