LM5015 High Voltage Monolithic Two-Switch Forward DC-DC Regulator General Description Features The LM5015 high voltage switch mode regulator features all the functions necessary to implement efficient high voltage Two-Switch Forward and Two-Switch Flyback regulators, using a minimum of external components. This easy to use regulator integrates high side and low side 75 Volt N-Channel MOSFETs with a minimum 1 Amp peak current limit. The voltage across the MOSFETs employed in the two-switch topology is clamped to the input voltage, allowing the input voltage range to approach the rating of the MOSFETs. The regulator control method is based on current mode control providing inherent ease of loop compensation and line feedforward for superior rejection of input transients. The operating frequency is set with a single resistor and is programmable up to 750 kHz. The oscillator can also be synchronized to an external clock. Additional protection features include cycle-by-cycle current limiting, thermal shutdown, under-voltage lockout and remote shutdown capability. The device is available in the TSSOP-14EP package featuring an exposed die attach pad to enhance thermal dissipation. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Dual Integrated 75V N-Channel MOSFETs Ultra-wide input voltage range: 4.25V to 75V Integrated high voltage bias regulator Adjustable output voltage 1.5% feedback reference accuracy Current mode control with selectable compensation Wide bandwidth error amplifier Integrated current sensing and limiting 50% maximum duty cycle limit Single resistor oscillator programming Oscillator synchronization capability Programmable soft-start Enable / Under-voltage Lockout (UVLO) pin Thermal shutdown Package ■ TSSOP-14EP (Exposed Pad) Typical Application Schematic 30034601 © 2007 National Semiconductor Corporation 300346 www.national.com LM5015 High Voltage Monolithic Two-Switch Forward DC-DC Regulator December 10, 2007 LM5015 Connection Diagram 30034602 Top View TSSOP-14 EP Package Ordering Information Order Number Package Type NSC Package Drawing Supplied As TSSOP-14 EP MXA14A 250 Units on Tape and Reel LM5015MH LM5015MHE 94 Units per Antistatic Tube LM5015MHX www.national.com 2500 Units on Tape and Reel 2 LM5015 Pin Descriptions Pin Name Description Application Information 1 AGND Analog ground Internal reference for the regulator control functions. The AGND pin and the PGND pin should be connected directly to minimize switching noise and prevent erratic operation. 2 RT Oscillator frequency programming and optional synchronization input The internal oscillator is set with a resistor between this pin and the AGND pin. The recommended switching frequency range is 25KHz to 750 kHz. The RT pin can accept synchronization pulses from an external clock. A 100 pF capacitor is recommended for coupling the synchronizing clock to the RT pin. 3 FB Feedback input of the internal error amplifier, for non-isolated applications This pin is connected to the inverting input of the internal error amplifier. The 1.26V reference is internally connected to the non-inverting input of the error amplifier. In isolated application using an external error amplifier, this pin should be connected to the AGND pin. 4 COMP Control input for the PWM comparator Internally connected to the open drain output of the internal error amplifier. COMP pull-up is provided by an internal 5 kΩ resistor which may be used to bias an opto-coupler transistor in isolated applications. 5 CFB Current feedback pin Feedback in put for high bandwidth isolated applications. An NPN current mirror couples the external opto-coupler current to the PWM comparator while maintaining a relatively constant opto-coupler voltage. 6 PGND Power ground Internally connected to the current sense resistor in the source of the low side MOSFET switch. Low side switch drain The drain terminal of the internal low side power MOSFET. Input supply pin for high side switch Internally connected to the drain of the high side power MOSFET. 7 LO 8 PVIN 9 HO High side switch source The source terminal of the high side power MOSFET. 10 BST High side bootstrap bias An external capacitor is required between the BST and the HO pins. A minimum capacitor value of 0.022 µF is recommended. The capacitor is charged from VCC via an internal diode during the power MOSFET off-time. 11 VCC Bias regulator output, or input for VCC tracks VIN up to 6.9V. At higher VIN voltages, VCC is regulated to 6.9 external bias supply Volts. A 0.47µF or greater ceramic decoupling capacitor is required on the VCC pin. An external bias voltage between 7V and 14V applied to the VCC pin will disable the internal VCC regulator, reduce internal power dissipation, and improve the converter efficiency. 12 VIN Analog input voltage pin Power supply Input for the switching regulator control blocks. 13 EN Enable / Under-Voltage LockOut / Shutdown input An external voltage divider can be used to set the input under-voltage lockout threshold. If the EN pin is left unconnected, a 6 µA pull-up current source pulls the EN pin high to enable the regulator. 14 SS Soft-start An internal 11 µA current source charges an external capacitor connected to the SS pin to soft-start the switching regulator by gradually raising the COMP pin voltage. NA EP Exposed Pad Exposed metal pad on the underside of the package. It is recommended to connect this pad to the PGND and AGND pins, and also to the PC board ground plane in order to improve heat dissipation. 3 www.national.com LM5015 COMP, FB, RT, SS to AGND PGND to AGND CFB Sink Current Maximum Junction Temperature Storage Temperature ESD Rating Human Body Model Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to AGND BST to AGND PVIN to HO, LO, PGND HO to PGND (Steady State) LO to PGND (Steady State) BST to VCC BST to HO VCC, EN to AGND 76V 90V 76V -3V to 76V -0.3V to 76V 76V 14V 14V -0.3V to 7V -0.3V to +0.3V 10 mA 150°C −65°C to + 150°C 2 kV Operating Ratings VIN Operation Junction Temperature 4.25V to 75V −40°C to + 125°C Electrical Characteristics Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of −40°C to + 125°C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. VVIN = 48V, RRT = 31.6 kΩ unless otherwise stated. See (Note 3). Symbol Parameters Conditions Min Typ Max Units 6.35 6.85 7.25 V STARTUP REGULATOR VVCC-REG IQ VCC Regulator Output VCC Current Limit VVCC = 6V VCC UVLO Threshold VCC increasing, VIN = VCC, EN=open 20 25 3.45 3.75 VCC UVLO Hysteresis VIN = VCC, EN = open 0.15 Bias Current (IIN) VFB = 1.5V Shutdown Current (IIN) VEN = 0V EN Shutdown Threshold VEN increasing VEN increasing mA 4.05 V 3.1 4.5 mA 110 170 µA 0.25 0.45 0.65 V 1.19 1.26 V EN THRESHOLDS EN Shutdown Hysteresis EN Standby Threshold 0.1 EN Standby Hysteresis EN Current Source V 1.3 V 0.1 V 6 µA MOSFET CHARACTERSTICS 0.93 Ω 0.05 5 µA 0.45 0.90 Ω 0.05 5 Low side MOSFET RDS(ON) plus ID = 0.6A Current Sense Resistance 0.49 MOSFET Leakage Current VLO = 75V High side MOSFET RDS(ON) ID = 0.6A MOSFET Leakage Current VPVIN= 75V, VHO = PGND Total Gate Charge including both VVCC = 8V Low and High side MOSFETs Pre-charge Switch ON Voltage including series blocking diode ID = 1 mA µA 9 nC 0.82 V CURRENT LIMIT ILIM Cycle by Cycle Current Limit 1 Cycle by Cycle Current Limit Delay 1.2 1.4 130 A ns OSCILLATOR FSW1 Frequency1 RRT = 31.6k 180 200 220 kHz FSW2 Frequency2 RRT = 15.4k 365 405 445 kHz SYNC Threshold VRT Increasing 3.2 SYNC Pulse Width Minimum VRT > VRT-SYNC + 0.5V VRT-SYNC www.national.com 4 V 15 ns Parameters Conditions Min Typ Max Units PWM COMPARATOR Maximum Duty Cycle VCOMP-OS Min On-time VCOMP > VCOMP-OS Min On-time VCOMP < VCOMP-OS COMP to PWM Comparator Offset 49 % 140 ns 0 ns 0.9 1.3 1.55 1.236 1.26 1.274 V ERROR AMPLIFIER VFB-REF Feedback Reference Voltage Internal reference, VFB = VCOMP FB Bias Current 10 DC Gain V nA 72 dB COMP Sink Current VCOMP = 250mV mA COMP Short Circuit Current VFB = 0, VCOMP = 0 0.9 1.2 1.5 COMP Open Circuit Voltage VFB = 0 4.5 5.15 5.95 2 mA V COMP to SW Delay 50 ns Unity Gain Bandwidth 4 MHz SOFT START Soft-start Current Source 8 11 14 µA Soft-start to COMP Offset 0.3 0.5 0.7 V THERMAL SHUTDOWN TSD Thermal Shutdown Threshold 165 °C Thermal Shutdown Hysteresis 25 °C THERMAL RESISTANCE θJC Junction to Case 6.6 °C/W θJA Junction to Ambient 40 °C/W Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The human body model is a 100pF capacitor discharged through a 1.5 kΩ resistor into each pin. Test Method is per JESD-22-A114. Note 3: Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate National’s Average Outgoing Quality Level (AOQL). 5 www.national.com LM5015 Symbol LM5015 Typical Performance Characteristics Demo-board Efficiency vs IOUT and VIN VFB vs Temperature 30034603 30034604 IQ (non-switching) vs VIN VCC vs VIN 30034605 30034606 RDS(ON) vs VCC vs Temperature IEN vs VIN vs Temperature 30034607 www.national.com 30034608 6 LM5015 ILIM vs VCC ILIM vs VCC vs Temperature 30034609 30034610 Fsw vs RRT Fsw vs Temperature 30034612 30034611 Fsw vs VCC Error Amplifier Gain/Phase 30034614 30034613 7 www.national.com LM5015 30034615 FIGURE 1. Block Diagram www.national.com 8 The LM5015 high voltage switching regulator features all the functions necessary to implement an efficient power converter using a Two-Switch Forward or Two-Switch Flyback topology. The voltage across the MOSFETs employed in the twoswitch topology is clamped to the input voltage, allowing the input voltage range to approach the rating of the MOSFETs. The regulator control method is based upon current mode control providing cycle-by-cycle current limit, inherent input voltage feed-forward and simple feedback loop compensation. Referring to the functional block diagram shown in Figure1, the operating principle of the LM5015 regulator is as follows: At the beginning of each switching cycle, the oscillator sets the driver logic and turns on both the high and low side power MOSFETs to conduct current through the inductor or power transformer. The peak current in the MOSFET is controlled by the voltage at the COMP pin. The COMP voltage, which is determined by the feedback circuit, is compared with the sensed current signal of the internal low side power MOSFET. When the current signal exceeds the COMP voltage, the PWM comparator resets the driver logic, turning off both power MOSFETs. At the end of the switching cycle the driver logic is set again by the oscillator to initiate the next switching period. The LM5015 also contains dedicated circuitry to protect the IC from abnormal operating conditions. Cycle-by-cycle current limiting prevents the power MOSFET current from exceeding 1 Amp. Thermal Shutdown circuitry holds the driver logic in reset when the die temperature reaches 165°C, and returns to normal operation when the die temperature drops by approximately 25°C. The EN pin can be used as an input voltage under-voltage lockout (UVLO) during start-up to pre- Bias Input (VIN) and Power Input (PVIN) The LM5015 provides two separate input power pins, VIN and PVIN, allowing for flexible decoupling options. The VIN pin provides power to the low drop-out VCC bias regulator which powers all internal control blocks. The PVIN connects directly to the high side MOSFET drain. If used with a single input source, the recommended configuration is shown in Figure 2a. Separate input pins allow the bias input (VIN) to be de-coupled from the main power input as shown. It is possible to directly connect the VIN and PVIN pins for applications with localized de-coupling capacitors. For applications where a lower voltage auxiliary source is available, the configuration shown in Figure 2b can be used. Powering the VIN pin with a relatively low voltage auxiliary source reduces the IC power dissipation and increases the conversion efficiency, especially when the main power source for PVIN is relatively large. The VIN and PVIN pins are independent and can be separately biased at any voltages within the 4.25V to 75V recommended operating range. In high voltage applications extra care should be taken to ensure that the VIN and PVIN pins do not exceed the Absolute Maximum Voltage Ratings of 76V. Voltage ringing on the input line during line transients that exceeds the Absolute Maximum Ratings can damage the IC. Both careful PC board layout and the use of quality bypass capacitors located close to the VIN and AGND pins, and to the PVIN to PGND pins, are essential. 30034616 FIGURE 2. Analog and Power Input Ports 9 www.national.com LM5015 vent operation with less than the minimum desired input voltage. Functional Description LM5015 The PVIN and PGND pins are internally connected to the high and low side power MOSFETs, respectively. When designing the PC board, the input filter capacitor should connect directly to these pins with short connection traces. The VIN operating range is 4.25V to 75V. The current drawn into the VIN pin depends primarily on the gate charge of the internal power MOSFETs, the switching frequency, and any external load on the VCC pin. It is recommended that a small filter shown in Figure 2 be used for the VIN input to suppress transients which may occur at the input supply. This is particularly important when VIN is operated close to the maximum operating rating of the LM5015. External Synchronization The LM5015 can be synchronized to the rising edge of an external clock. Because the oscillator uses a divide-by-two circuit, the switching frequency FSW in the above equation is actually half the native oscillator frequency. Therefore, in order to synchronize, the external clock must have a frequency higher than twice the free running FSW set by the RT resistor. The clock signal should be coupled through a 100 pF capacitor into the RT pin. A peak voltage level greater than 3.2V at the RT pin is required for detection of the sync pulse. The DC voltage across the RT resistor is internally regulated at 1.5 volts. The negative portion of the AC voltage of the synchronizing clock is clamped to 1.5V by an amplifier inside the LM5015 with approximately 100Ω output impedance. Therefore, the AC pulse superimposed on the RT resistor must have positive pulse amplitude of 1.7V or greater to successfully synchronize the oscillator. The sync pulse width measured at the RT pin should have a duration greater than 15 ns and less than 5% of the switching period. The RT resistor is always required, whether the oscillator is free running or externally synchronized. The RT resistor should be located very close to the device and connected directly to the RT and AGND pins of the LM5015. High Voltage VCC Regulator The LM5015 VCC Low Drop Out (LDO) regulator allows the LM5015 to operate at the lowest possible input voltage. When power is applied to the VIN pin and the EN pin voltage is greater than 0.45V, the VCC regulator is enabled, supplying current into the external capacitor connected to the VCC pin. When the VIN voltage is between 4.25V and 6.9V, the VCC voltage is approximately equal to the VIN voltage. When the voltage on the VIN pin exceeds 6.9V, the VCC pin voltage is regulated at 6.9V. The total input operating range of the VCC LDO regulator is 4.25V to 75V. The output of the VCC regulator is current limited to 20mA. During power-up, the VCC regulator supplies current into the required decoupling capacitor (0.47 µF or greater ceramic capacitor) at the VCC pin. When the voltage at the VCC pin exceeds the VCC UVLO threshold of 3.75V and the EN pin is greater than 1.26V the PWM controller is enabled and switching begins. The controller remains enabled until VCC falls below 3.60V or the EN pin falls below 1.16V. An auxiliary supply voltage can be applied to the VCC pin to reduce the IC power dissipation. If the auxiliary voltage is greater than 6.9V, the internal regulator will essentially shutoff, and internal power dissipation will be decreased by the VIN-VCC voltage difference times the operating current. The externally applied VCC voltage should not exceed 14V. The VCC regulator series pass MOSFET includes a body diode (see Figure 1) between VCC and VIN that should not be forward biased in normal operation. Therefore, the auxiliary VCC voltage should never exceed the VIN voltage. Enable / Standby The LM5015 contains a dual level Enable circuit. When the EN pin voltage is below 0.45V, the IC is in a low current shutdown mode with the VCC LDO disabled. When the EN pin voltage is raised above the 0.45V shutdown threshold but below the 1.26V standby threshold, the VCC LDO regulator is enabled, while the remainder of the IC is disabled. When the EN pin voltage is raised above the 1.26V standby threshold, all functions are enabled and normal operation begins. An internal 6 µA current source pulls up the EN pin to activate the IC when the EN pin is left disconnected. An external set-point resistor divider from VIN to AGND can be used to determine the minimum operating input voltage of the regulator. The divider must be designed such that the EN pin exceeds the 1.26V standby threshold when VIN is in the desired operating range. The internal 6 µA current source should be included when determining the resistor values. The shutdown and standby thresholds have 100 mV hysteresis to prevent noise from toggling between modes. The EN pin is internally protected by a 6V Zener diode through a 1 kΩ resistor. The enabling voltage may exceed the Zener voltage, however the Zener current should be limited to less than 4 mA. High Side Bootstrap Bias The high side bootstrap bias provides power to drive the high side power MOSFET. An external capacitor is required between the BST and the HO pins. A minimum capacitor value of 0.022 µF is recommended. The capacitor is charged from VCC via an internal diode during each power MOSFET offtime. Error Amplifier and PWM Comparator Oscillator An internal high gain error amplifier generates an error signal proportional to the difference between the regulated output voltage and an internal precision reference. The output of the error amplifier is connected to the COMP pin allowing the user to add loop compensation, typically a Type II network, as illustrated in Figure 3. This network creates a pole at the origin that rolls off the high DC gain of the amplifier, which is necessary to accurately regulate the output voltage. A zero provides phase boost near the open loop unity gain frequency, and a high frequency pole attenuates switching noise. The PWM comparator compares the current sense signal from the current sense amplifier to the error amplifier output voltage at the COMP pin. A single external resistor connected between RT and AGND pins sets the LM5015 oscillator frequency. To set a desired oscillator frequency (FSW), the necessary value for the RT resistor can be calculated from the following equation: The tolerance of the external resistor and the frequency tolerance indicated in the Electrical Characteristics table must be taken into account when determining the total variation of the switching frequency. www.national.com 10 LM5015 30034618 FIGURE 3. Type II Compensator When isolation between primary and secondary circuits is required, the Error Amplifier is usually disabled by connecting the FB pin to AGND. This allows the COMP pin to be driven directly by the collector of an opto-coupler. In isolated designs the error amplifier is located on the secondary circuit and drives the opto-coupler LED. The compensation network is connected to the secondary side error amplifier. An example of an isolated regulator with an opto-coupler is shown in Figure 13. Thermal Protection Current Sense Amplifier Power MOSFETs The LM5015 employs peak current mode control which also provides a cycle-by-cycle over current protection feature. An internal 42 milli-Ohm current sense resistor measures the current in the low side power MOSFET source. The sense resistor voltage is amplified 30 times to provide a 1.25V/A signal into the current limit comparator. Current limiting is initiated if the internal current limit comparator input exceeds the 1.5V threshold, corresponding to 1.2A. When the current limit comparator is triggered, the HO and LO output pins immediately switches to the high impedance state. The current sense signal provides the PWM comparator with a control signal that reaches 1.5V when the MOSFET current is 1.2A. To prevent erratic operation at low duty cycle, a leading edge blanking circuit attenuates the current sense signal for 100 ns when the power MOSFET is turned on. When the MOSFET is initially turned on, current spikes from the power MOSFET drain-source and gate-source capacitances flow through the current sense resistor. These transient currents normally cease within 50 ns with proper selection of rectifier diodes and proper PC board layout. The LM5015 switching regulator includes two N-Channel MOSFETs each with 450 mΩ nominal on-resistance. The drain of the high side MOSFET is the PVIN pin, and the source the HO pin. The drain of the low side MOSFET is the LO pin, and the source is internally connected to the PGND pin via the 42 mΩ internal current sense resistor. The on-resistance of the LM5015 MOSFETs varies with temperature as shown in the Typical Performance Characteristics graph. The typical gate charge for each MOSFETs is 4.5 nC which is supplied from the VCC and BST pins, respectively, when the MOSFETs are turned on. The maximum duty cycle of the power MOSFETs is limited less than 50%. This is achieved by an oscillator divide-by-two circuit with an additional 50 ns of forced off-time introduced between the CLK and RS Flip-Flop. Consequently, the maximum duty cycle is limited by the following equation: Internal Thermal Shutdown circuitry is provided to protect the IC in the event the maximum junction temperature is exceeded. When the 165°C junction temperature threshold is reached, the regulator is forced into a low power standby state, disabling all functions except the VCC regulator. Thermal hysteresis allows the IC to cool down by 25°C before it is re-enabled. DutyMax_Limit=(0.5 - 50 ns x FSW) x 100% Where FSW is the switching frequency in Hertz (Hz). The purpose of limiting the maximum duty cycle less than 50% is to guarantee successful reset of the power transformer in the Two-Switch Forward converter topology. See applications information below for more detail. 11 www.national.com LM5015 rating of the MOSFETs. Whereas, the maximum operating voltage of a Single-Switch Forward converter is typically limited to half the MOSFET voltage rating. 2. The power transformer of a Two-Switch Forward converter is simpler, and hence costs less, than that of a Single-Switch Forward converter, because the TwoSwitch converter transformer eliminates the tertiary reset winding that is normally required in the Single-Switch converter. Figure 4 illustrates the Two-Switch Forward converter topology. The power circuit consists of an input capacitor CIN, two MOSFET switches QH and QL, two clamp diodes DH and DL, a power transformer T1, two rectifier diodes D1 and D2, an output inductor LO, and an output capacitor Co. Since the LM5015 integrates both QH and QL, a low cost Two-Switch Forward converter can be realized without a need for discrete power MOSFETs. With a slightly higher cost, the two rectifier diodes D1 and D2 on the secondary side of the power transformer can be replaced with synchronous rectifier MOSFETs to improve efficiency in applications with relatively low output voltage. Application Information The following information is intended to provide guidelines for the power supply designer using the LM5015. TWO-SWITCH FORWARD TOPOLOGY Two-Switch Forward converter, like the conventional SingleSwitch Forward converter, is derived from the Buck converter topology. The main difference between a Forward converter and a Buck is that a power transformer is introduced in the forward converter. The transformer realizes the input-output isolation, and the turns ratio provides a means to optimize the duty cycle for the particular input and output voltage requirements of the application. The Two-Switch Forward converter employs two power MOSFET switches instead of the one switch of the Single-Switch Forward converter. However the two-switch approach offers two major advantages over its single-switch counterpart: 1. The voltage across the power MOSFET switches in a Two-Switch Forward converter is clamped to the input voltage, allowing the input voltage range to approach the 30034619 FIGURE 4. Two-Switch Forward Converter Topology www.national.com 12 The power transformer is magnetized by the application of the input voltage, and power flows to the secondary side circuit via transformer coupling. When the MOSFETS are turned OFF, as shown in Figure 5(b), the power flow to the primary is cut off. The residual magnetizing inductance of the power transformer reverses the voltage across the primary winding and forces the two clamp diodes DH and DL to conduct. This effectively clamps the MOSFETs voltage to the input voltage, and applies the input voltage in reversed polarity to the power transformer primary winding to demagnetize and reset the transformer. When the MOSFETS are turned ON, as shown in Figure 5(a), the input voltage is applied to the power transformer primary. 30034621 FIGURE 5. Operating Modes of Two-Switch Forward Converter 13 www.national.com LM5015 Figure 5 shows the two operating modes of the Two-Switch Forward converter. During operation, the two MOSFETS are turned ON and OFF simultaneously. The output voltage is regulated by modulating the duty cycle of the MOSFETs. The relationship between the input voltage VIN, output voltage VOUT, duty cycle D, rectifier diode forward drop VF, and transformer turns ratio k is defined by the following equation. LM5015 Note that the power transformer primary receives the voltage of the nearly equal magnitude but opposite polarities during the ON and OFF period of the power MOSFETs. In order to guarantee the volt-second balance between the magnetizing and demagnetizing intervals, the LM5015 limits the maximum duty cycle less than 50%. Therefore, an LM5015 Two-Switch Forward regulator always achieves a complete reset of the power transformer during each switching cycle. The LM5015 can also be used to implement a Two-Switch Flyback regulator (Figure 14). The voltage across the MOS- www.national.com FETs employed in the Two-Switch Flyback converter is also clamped to the input voltage, allowing the input voltage range to approach the rating of the MOSFETs. Generally the Flyback converter is simpler and costs less than the Forward converter. However, the Flyback converter will have higher ripple current and voltages, and the conversion efficiency is typically lower. 14 For example, if the LM5015 is to be enabled when VPWR reaches 16V, IDIVIDER could be chosen as 500 µA which would set R1 to 29.4 kΩ and R2 to 2.49 kΩ. If the voltage at the EN pin can exceed 6V, then the current into the 6V protection Zener must be limited below 4 mA by the external resistors. Be sure to check both the power and voltage rating for the selected R1 resistor (some 0603 resistors are rated as low as 50V maximum operating voltage). 30034623 FIGURE 6. Basic EN (UVLO) Configuration A remote enable function can be accomplished with open drain device(s) connected to the EN pin as shown in Figure 7. A MOSFET or an NPN transistor connected to the EN pin will force the regulator into the low power ‘off’ state. Adding a PN diode in the drain (or collector) provides the offset to achieve the standby state. The advantage of standby is that the VCC LDO is not disabled and external circuitry powered by VCC remains functional. 30034624 FIGURE 7. Remote Standby and Disable Control 15 www.national.com LM5015 where VPWR is the desired turn-on voltage and IDIVIDER is the user-defined current through R1 and R2. EN / UVLO VOLTAGE DIVIDER SELECTION Two dedicated comparators connected to the EN pin are used to implement input under-voltage lockout and a shutdown condition. When the EN pin voltage is below 0.45V, the controller is in a low current shutdown mode where the VIN current is reduced to 110 µA. For an EN pin voltage greater than 0.45V but less than 1.26V the controller is in standby mode, with all internal circuits operational, but with the power MOSFETs disabled. Once the EN pin voltage is greater than 1.26V, the controller is fully enabled and the HO and LO outputs commence switching. Two external resistors can be used to program the minimum operational voltage for the power converter as shown in Figure 6. When the EN pin voltage falls below the 1.26V threshold, an internal 100 mV threshold hysteresis prevents noise from toggling the state. Therefore, the voltage at the EN pin must be reduced to 1.16V to transition to the standby state. Resistance values for R1 and R2 can be determined from the following equations, LM5015 follow the SS voltage under the control of the open-drain SS buffer amplifier. The CSS capacitor will cause the COMP voltage to gradually increase, until the output voltage achieves regulation, and the error amplifier assumes control of the COMP and the PWM duty cycle. The CSS capacitor continues charging by the internal 11 µA current source, preventing the SS voltage from interfering with the normal error amplifier function. During shutdown, the SS discharge MOSFET conducts to discharge the CSS capacitor. SOFT-START Soft-start is implemented with an external capacitor CSS connected to the SS pin as shown in Figure 8. The SS discharge MOSFET conducts during Shutdown and Standby modes. When the SS pin is low, the COMP voltage is held below the PWM offset voltage (1.3V) by the SS buffer amplifier, thus inhibiting PWM pulses. When the EN pin exceeds the 1.26V standby threshold, the ENABLE signal will turn-off the SS discharge MOSFET and allow the internal 11 µA current source to charge the SS capacitor. The COMP voltage will 30034625 FIGURE 8. Soft-Start www.national.com 16 30034626 FIGURE 9. Conventional Isolated Feedback protect the CFB pin by limiting the opto-coupler current to less than 10 mA. The 1 kΩ resistor from the opto-coupler collector to ground is introduced to protect the opto-coupler from excess voltage by limiting its VCE to less than 50% of Vcc max. When the output voltage is below regulation, no current flows into the CFB pin and the PWM of the LM5015 operates at maximum duty cycle. HIGH BANDWIDTH ISOLATED FEEDBACK DESIGN USING THE CFB PIN The LM5015 also includes a current mirror circuit for optional high bandwidth feedback loop design. As shown in Figure 10, the emitter of the opto-coupler transistor can be connected to the CFB pin, and the collector connected to VCC through an external 1 kΩ resistor. The 1 kΩ resistor to VCC is used to 17 www.national.com LM5015 signal across the isolation boundary, as shown in Figure 9. The LM5015 provides built-in pull-up for the collector of the opto-coupler at the COMP pin through a 5 kΩ internal resistor. Similar compensation network used in Figure 3 is applicable to the external, secondary-side error amplifier. The LM431A shown in Figure 9 provides both the voltage reference and error amplifier required to regulate the isolated output voltage. CONVENTIONAL ISOLATED OUTPUT FEEDBACK DESIGNS When isolation between the primary and secondary circuits is required, the internal error amplifier is usually disabled by connecting the FB pin to AGND, and an external error amplifier is employed on the secondary side of the isolation boundary. An opto-coupler is normally used to send the feedback LM5015 30034627 FIGURE 10. High bandwidth Isolated Feedback Using CFB Pin The two external pull-up and pull-down resistors are effectively connected in parallel for ac signal, yielding a collector resistance on the opto-coupler of 0.5 kΩ. This resistance is 10 times smaller than the internal pull up resistor and the pole associated with the collector-base capacitance of the optocoupler transistor is pushed out to a decade higher frequency. Moving the opto-coupler pole to a higher frequency allows higher loop bandwidth capability than conventional isolated feedback designs (see Figure 9). by above equation is 0.330. Selecting 24.3 kΩ for RO1, then RO2 should be 8.06 kΩ. In a similar non-isolated converter design using the internal error amplifier, the divider’s resistors ratio is 0.337, therefore if 24.3 kΩ is selected for RO1, then RO2 should be 8.20 kΩ. Multiple resistors in series or parallel combinations for either RO1, or RO2, or both, may be necessary to set a required output voltage. Note that the accuracy of the output voltage setting is determined by the tolerance of the divider resistors as well as the accuracy of VREF. The accuracy of the LM5015 internal VREF is 1.5%, and the most popular chip resistors have a tolerance of 1%, therefore the achievable output accuracy with the internal error amplifier and 1% resistors is about 2.5%. To achieve better output voltage accuracy, use an external voltage reference with higher precision and resistors of tighter tolerance, such as the 0.1%, resistors for RO1 and RO2. OUTPUT VOLTAGE Output voltage is normally set with a resistor divider shown in Figure 11. To set the regulator’s output voltage to VO, the two resistors must satisfy the following equation: PRINTED CIRCUIT BOARD LAYOUT The LM5015 Current Sense and PWM comparators are very fast and may respond to short duration noise pulses. The components at the HO, LO, COMP, EN, VCC and the RT pins should be as physically close as possible to the IC, thereby minimizing noise pickup on the PC board tracks. The HO and LO output pins of the LM5015 should have short, wide conductors to the power path inductors, transformers and capacitors in order to minimize parasitic inductance that reduces efficiency and increases conducted and radiated noise. Ceramic decoupling capacitors are recommended between the VIN pin to the AGND pin, between the PVIN pin and PGND pin, and between the VCC pin to the AGND pin. Use short, direct connections to avoid clock jitter due to ground voltage differentials. Small package surface mount X7R or X5R capacitors are preferred for high frequency performance and limited variation over temperature and applied voltage. If an application using the LM5015 produces high junction temperatures during normal operation, multiple vias from the exposed metal pad on the underside of the IC package to a PC board ground plane will help conduct heat away from the where VREF is the reference voltage of the error amplifier, which is 1.26V for the LM5015’s internal error amplifier. 30034629 FIGURE 11. Output Voltage Setting In isolated designs, the reference and error amplifier are located on the secondary side. To obtain a 5V output in an isolated feedback design using LMV431A (whose nominal VREF is1.24V), the feedback divider resistors ratio specified www.national.com 18 A 1:1 dc-dc transformer with the input/output operating range of 5V to 15V 48V NON-ISOLATED TWO-SWITCH FORWARD The Non-Isolated Two-Switch Forward converter shown in Figure 12 utilizes the internal voltage reference for the regulation set-point. The output is +5V at 2.5A while the input voltage can vary from 36V to 72V. The switching frequency is 300 kHz. An auxiliary winding on transformer (T1) provides 10V to power the LM5015 when the output is in regulation. This disables the internal high voltage VCC LDO regulator and improves efficiency. The converter can be shut down by driving the EN input below 1.26V with an open-collector or open-drain transistor. An external synchronizing frequency can be applied to the SYNC input. Application Examples The following schematics present four examples dc-dc converters utilizing the LM5015 switching regulator IC: 1. Non-Isolated Two-Switch Forward for 48V input and 5V 2.5A output, 2. Isolated Two-Switch Forward for 48V input and 5V 2.5A output 3. Isolated Two-Switch Flyback converter for 48V input and 5V 2.5A output, 30034630 FIGURE 12. Non-Isolated Two-Switch Forward 19 www.national.com LM5015 4. IC. Judicious positioning of the PC board within the end product, along with use of any available air flow will help reduce the junction temperature. If using forced air cooling, avoid placing the LM5015 in the airflow shadow of large components, such as input or output capacitors, inductors or transformers. LM5015 coupler LED, which sets the COMP pin voltage. The output is +5V at 2.5A and the input voltage ranges from 36V to 72V. The switching frequency is 300 kHz. The functions of the EN and SYNC inputs are the same as in the previous example circuit. 48V ISOLATED TWO-SWITCH FORWARD The Isolated Two-Switch Forward converter shown in Figure 13 utilizes a 1.24V voltage reference (LMV431A) located on the isolated secondary side for the regulation set-point. The LM5015 internal error amplifier is disabled by grounding the FB pin. The LMV431A controls the current through the opto- 30034631 FIGURE 13. Isolated Two-Switch Forward is less complex than the previous Forward converter example in Figure 13. However, the Flyback converter produces higher input and output ripples of voltage and currents, and lower conversion efficiency by about 2%. The functions of the EN and SYNC inputs are the same as in the previous example circuits. This circuit can be used with the LM5073 for a low cost isolated Power over Ethernet (PoE) Power Device (PD) application that does not require a discrete power MOSFET. ISOLATED TWO-SWITCH FLYBACK The Isolated Two-Switch Flyback converter shown in Figure 14 utilizes a 1.24V voltage reference (LMV431A) located on the isolated secondary side for the regulation set-point. The LM5015 internal error amplifier is disabled by grounding the FB pin. The LMV431A controls the current through the optocoupler LED, which sets the COMP pin voltage. The output is +5V at 2.5A and the input voltage ranges from 36V to 72V. The switching frequency is 300 kHz. The Flyback converter 30034632 FIGURE 14. Isolated Two-Switch Flyback www.national.com 20 30034633 FIGURE 15. DC-DC Transformer 21 www.national.com LM5015 output voltage will be approximately equal to the input voltage. A Zener diode Z1 is used at the output rail as a simple means to protect the output against over-voltage under light and no load conditions. The maximum load of this example circuit is 0.3A, and the operating voltage range is from 5V to 15V. DC-DC TRANSFORMER The DC-DC transformer shown in Figure 15 provides a 1:1 input voltage to output voltage conversion with ground isolation. The circuit operates in open loop manner operating at the maximum duty cycle limit of the LM5015. The power transformer primary-secondary turns ratio is 1:2 (primary to secondary). Therefore, at the maximum duty cycle of 0.5, the LM5015 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Exposed Pad Package NS Package Number MXA14A www.national.com 22 LM5015 Notes 23 www.national.com LM5015 High Voltage Monolithic Two-Switch Forward DC-DC Regulator Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560