Infrared detector modules with preamps Metal dewar type High sensitivity modules of easy-to-use These devices combine a dewar type detector with a compatible preamplifier, and easily operate to detect infrared radiation just by connecting to a DC power supply. InGaAs and InSb detectors are provided as standard devices (liquid nitrogen cooling). Customdesigned devices with different active areas, FOV or amplifier gain, etc. are also available to meet your specific needs. Features Applications Compact integral detector unit Infrared detection Optimum connections between the detector element and preamplifier allow amplified signals to be easily obtained. Accessories Required power supply specifications · · · · · G7754 series, P7751 series: ±15 V (±12.0 to ±17.5 V can also be used) Current capacity: 1.5 times or more of each module's maximum current consumption Ripple noise: 5 mVp-p or less Analog power supply only Recommended DC power supplies: E3620A, E3630A (Agilent Technologies) Cable (for DC power supply): 2 m (connector installed at one end) A4372-02 BNC-BNC coaxial cable (for signal output): 2 m Instruction manual Specifications / Absolute maximum ratings External power supply*1 Type No. Detector element Active area Supply voltage (V) Absolute maximum ratings Operating Storage Supply External input temperature temperature capacitance voltage Topr Tstg (mA) (V) (°C) (°C) (mm) Min. Typ. Max. G7754-01 φ1 InGaAs ±23 G7754-03 φ3 ±12.0 ±15.0 ±17.5 ±18 0 to +40 -20 to +50 P7751-01 InSb (P5968-060) φ0.6 ±30 P7751-02 InSb (P5968-200) φ2 *1: Use only an analog power supply. Note: Nitrogen hold time: 12 hours or more (at the time of shipment) Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. Electrical and optical characteristics (Typ.) Measurement Noise Photo Peak condition Cutoff Cut-off sensitivity equivalent sensitivity Output power frequency wavelength S Element wavelength impedance Type No. NEP fc λc λ=λp temperature λp *2 λ=λp T (Hz) (Ω) (°C) (μm) (μm) (V/W) (W/Hz1/2) 9 G7754-01 2 × 10 3 × 10-14 2 to 500 2.0 2.4 G7754-03 5 × 108 1.5 × 10-13 2 to 500 -196 50 4 P7751-01* 3 × 10-13 5 to 10000 3 × 108 5.3 5.5 4 8 -12 P7751-02* 1.5 × 10 1 × 10 5 to 12000 *2: f=100 Hz (G7754-01, G7754-03), f=1.2 kHz (P7751-01, P7751-02) *3: Vs=±15 V *4: FOV=60° www.hamamatsu.com Maximum Maximum output current voltage consumption*3 RL=1 kΩ (V) ±10 ±10 ±10 ±10 (mA) ±15 ±15 ±20 ±20 1 Infrared detector modules with preamps Metal dewar type Spectral response (Typ. T=-196 °C) 1013 D* (λ, 1200, 1) (cm · Hz1/2/W) G7754-01/-03 1012 11 10 P7751-01/-02 10 10 109 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Wavelength (µm) KIRDB0076EF Dimensional outline (unit: mm) 18 ± 1 DC input voltage ±15 V (4-pin connector) 32 ± 1 51 ± 1 11.5 ± 1 LN2 fill port Signal output (BNC) Foam polystyrene plug 6.5 ± 1 Amp 127.5 ± 1 10 ± 2 12 ± 2 11 ± 1 49.5 ± 1 172 ± 2 Pump-out pipe 90.5 ± 2 70.0 ± 1 63.5 ± 1 37 ± 1 Window InSb, MCT 12 ± 0.5 InGaAs 14.3 ± 0.5 Photosensitive surface KIRDA0010EE 2 Infrared detector modules with preamps Metal dewar type Cable (for DC power supply) A4372-02 2000 ± 100 70 ± 10 4.8 27 11 1.1 10 ± 3 Shielded wire (4 conductors) Solder processing Connector: HR10-7P-4P (made by Hirose Electric) Pin no. Pin connection -Vs GND GND +Vs Lead color Blue Black/white/blue stranded wire White KIRDA0196EB Precaution for use · The detector should not be placed horizontally during use. · Using these detectors in an environment subjected to vibration may cause microphonic noise. Take measures to prevent vibration as needed. The P7751-01 conforms to European EMC directives: EN 61326-1 Class B. Information described in this material is current as of November, 2012. Product specifications are subject to change without prior notice due to improvements or other reasons. Before assembly into final products, please contact us for the delivery specification sheet to check the latest information. Type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(X)" which means preliminary specifications or a suffix "(Z)" which means developmental specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Thorshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1 int. 6, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 China: Hamamatsu Photonics (China) Co., Ltd.: 1201 Tower B, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KIRD1024E09 Nov. 2012 DN 3