Datasheet

Amplifiers for infrared detector
C4159 series, C5185-02
Low noise amplifiers for infrared detector
(InSb, InAs, InAsSb, InGaAs)
Accessories
Required power supply specifications
Instruction manual
Power cable (one end with 4-pin connector for connection to
amplifier and the other end unterminated, 2 m) A4372-02
· C4159 series: ±15 V ± 0.5
· C5185-02: ±15 V ± 0.5
· Current-carrying capacity: 1.5 times or more of amplifier's
maximum current consumption
· Ripple noise: 5 mVp-p or less
· Analog power supply only
Recommended DC power supply: E3620A, E3630A (Agilent
Technologies)
Absolute maximum ratings (Ta=25 °C)
Parameter
Supply voltage
Operating temperature
Storage temperature
Value
18.0 max.
0 to +40
-20 to +70
Unit
V
°C
°C
Note: Absolute maximum ratings are the values that must not be exceeded at any time. If even one of the absolute maximum ratings
is exceeded even for a moment, the product quality may be impaired. Always be sure to use the product within the absolute
maximum ratings.
Amplifiers for photovoltaic detectors (Typ.)
Parameter
C4159-01
C4159-04
C4159-05
C4159-06
C4159-07
Unit
Dewar type InSb
Non-cooled type InAs
TE-cooled type
(P5968-060, P5968-100) Dewar type InSb
(P10090-01)
Dewar type InAs
Applicable detector*1 *2 *3
InAs
Dewar type InAsSb
TE-cooled type InAsSb
(P5968-200)
(P7163)
(P10090-11/-21)
(P11120-201, P12691-201)
(P11120-901)
2 × 107, 2 × 106, 2 × 105
108, 107, 106
106, 105, 104
106, 105, 104
108, 107, 106
V/A
Conversion impedance
(3 ranges switchable) (3 ranges switchable) (3 ranges switchable) (3 ranges switchable) (3 ranges switchable)
Frequency response
DC to 45 kHz
DC to 15 kHz
DC to 100 kHz
DC to 100 kHz
DC to 100 kHz*4
(amp only, -3 dB)
Output impedance
50
50
50
50
50
Ω
Maximum output voltage
+10
+10
+10
+10
+10
V
(1 kΩ load)
Output offset voltage
±5
±5
±10
±5
±5
mV
0.15 (108, 107 range)
0.15 (108, 107 range)
Equivalent input noise
pA/Hz1/2
0.55
6
10
0.65 (106 range)
0.65 (106 range)
current*5 (f=1 kHz)
Reverse voltage
Limited to 0 V operation
External power supply*6
±15
V
Current consumption
+30, -10 max.
+30, -22 max.
mA
These amplifiers cannot operate multiple detectors.
Consult us before purchasing if you want to use with a detector other than listed here.
Consult us before purchasing if you want to use with a multi-element detector.
When connected to a detector, frequency response becomes 60 kHz or less depending on the detector active area. (ϕ0.6 mm: 60
kHz or less, ϕ1 mm: 25 kHz or less) Ringing occurs in the output if the rise time tr (0 to 90%) of incident light is approximately 100
μs or less. The ringing becomes larger as the rise time becomes shorter. No ringing occurs when detecting sine-wave light. (For
information on the ringing specifications, see page 2.)
*5: Input resistance: 1 MΩ (C4159-01/-04/-05), 500 Ω (C4159-06/-07)
*6: Recommended DC power supply (analog power supply): ±15 V
Current capacity: More than 1.5 times the maximum current consumption
Ripple noise: 5 mVp-p or less
Note: Output noise voltage = Equivalent input noise current × Conversion impedance
For information about accessories except for the amplifiers, refer to our datasheet “Accessories for infrared detector”.
1
*1:
*2:
*3:
*4:
www.hamamatsu.com
Amplifiers for infrared detector
C4159 series, C5185-02
Ringing Vri
Ringing specifications
5V
90%
10%
tr
Incident light
Output waveform when tr=40 μs and photosensitive area is ϕ0.6 mm
Ringing Vri ≤ 1.5 V
Oscillating cycle ≤ 3 cycles
KIRDC0090EA
Amplifier for InGaAs PIN photodiodes (Typ.)
Parameter
Applicable detector*7 *8
Conversion impedance
Frequency response
(amp only, -3 dB)
Output impedance
Maximum output voltage
(1 kΩ load)
Output offset voltage
Equivalent input noise current
(f=1 kHz)
Reverse voltage
External power supply*9
Current consumption
C4159-03
InGaAs
107, 106, 105
(3 ranges switchable)
Unit
-
DC to 15 kHz
-
50
Ω
+10
V
±5
mV
2.5
pA/Hz1/2
Can be applied from external unit
±15
±15 max.
V
mA
V/A
Amplifiers for photoconductive detectors (Typ.)*10
Parameter
Applicable detector*7 *8 *11
Input impedance
Voltage gain
Frequency response
(amp only, -3 dB)
Detector bias current
Output impedance
Maximum output voltage
(1 kΩ load)
Equivalent input noise voltage
(f=1 kHz)
External power supply*9
Current consumption
C5185-02
InSb (P6606 series)
5
66 (× 2000)
Unit
kΩ
dB
5 Hz to 250 kHz
-
5 mA, 10 mA, 15 mA (3 ranges switchable)
50
Ω
±10
V
2.6*12
nV/Hz1/2
±15
+100, -30 max.
V
mA
*7: These amplifiers cannot operate multiple detectors.
*8: Consult us before purchasing if you want to use with a detector other than listed here.
*9: Recommended DC power supply (analog power supply): ±15 V
Current capacity: More than 1.5 times the maximum current consumption
Ripple noise: 5 mVp-p or less
*10: Before purchasing, make sure the bias current to the detector matches the detector bias current specified in the above table.
*11: Consult us before purchasing if you want to use with a multi-element detector.
*12: At detector bias current max.
Note: Output noise voltage = Equivalent input noise voltage × Voltage gain
2
Amplifiers for infrared detector
C4159 series, C5185-02
Dimensional outlines (unit: mm, tolerance unless otherwise noted: ±1)
IN
OUT
11.5
24.5
30
PREAMPLIFIER
POWER
60
HIGH
MID
LOW
39.5
24.5
12.5
25
PREAMPLIFIER
POWER
60
37
4-pin connector
11.5
4-pin connector
C5185-02
HIGH
MID
LOW
IN
39.5
C4159-01/-03/-04/-05/-06/-07
OUT
BNC
Bias adjusting screw
Gain adjusting screw
Offset voltage
adjusting screw
BNC connector
BNC connector
85
18
30
18
26.2
23
KIRDA0048EB
Solder leads to these terminals.
PIN connections
GND
Cathode
Anode
Note: Socket for lead attachment is not provided.
KIRDA0046EC
A4372-02
2000 ± 100
70 ± 10
27
ϕ11
ϕ4.8
10 ± 3
ϕ1.1
23
15
35
21.2
85
Shielded wire (4 conductors)
Solder processing
Connector: HR10-7P-4P
(made by Hirose Electric)
Pin no.
Pin connection
Lead color
-Vs
GND
GND
+Vs
Black/white/blue
stranded wire
Blue
White
As viewed from connector side
KIRDA0196EB
3
Amplifiers for infrared detector
C4159 series, C5185-02
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Disclaimer
Information described in this material is current as of November, 2015.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866
Cat. No. KIRD1011E16 Nov. 2015 DN
4