HMC-C012 v03.1007 AMPLIFIERS 1 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz D E U N I T N O T C C S U I D D O PR Features P1dB Output Power: 10 Watts Gain: 40 dB Output IP3: +54 dBm Single Positive Supply: +12V Thermally Compensated and Protected TTL DC Power Enable Unconditionally Stable Heat Sink/Fan Accessories Available Typical Applications The HMC-C012 is ideal for: • Cellular/3G Infrastructure ew N r fo d e end m com e R Not ns g i s De • Automated Test Equipment (ATE) • Laboratory Use Functional Diagram General Description The HMC-C012 is a 10 Watt Power Amplifier Module suitable for Cellular/3G repeaters, wireless data, laboratory use and ATE applications. This extremely robust PA module is DC blocked, internally regulated and over voltage protected. Thermal protection/fault circuitry automatically turns off DC power if base temperature exceeds +75 °C and restores power at < +55 °C. Electrical Specifi cations, TA = +25° C, VIN = +12V Parameter Min. Frequency Range Max. Units GHz dB Gain 38 40 Input Return Loss 9.5 12 dB Output Return Loss 7.5 12 dB Output Power for 1 dB Compression (P1dB) 1-1 Typ. 0.4 - 1.0 10 W Saturated Output Power (Psat) 9 42 dBm Output Third Order Intercept (IP3) (Two-tone Input Power = -28 dBm each tone) 54 dBm Channel Output Power for -60 dBc ACPR (CDMA-2000, 1.98 MHz offset) 36 dBm Channel Output Power for -50 dBc ACPR (CDMA-2000, 885 kHz offset) 34 dBm Second Harmonic at Output P1dB -20 dBc Third Harmonic at Output P1dB -30 dBc Spurious at Output P1dB -65 Supply Current 6.5 dBc 7.0 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com A HMC-C012 v03.1007 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz D E U N I T N O T C C S U I D D O PR Gain vs. Temperature 44 1 Output IP3 vs. Temperature 42 AMPLIFIERS 60 GAIN (dB) 38 36 IP3 (dBm) 56 40 +25 C +50 C 0C 34 52 48 ew N r fo d e end m com e R Not ns g i s De +25 C +50 C 0C 44 32 30 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 40 0.3 1.1 0.4 0.5 44 42 42 40 40 38 +25 C +50 C 0C 32 32 0.5 0.6 0.7 0.8 0.9 1 30 0.3 1.1 0.4 FREQUENCY (GHz) 1 1.1 0.5 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) ACPR, CDMA-2000, 1.98 MHz Offset ACPR, CDMA-2000, 885 kHz Offset -40 -30 400 MHz 800 MHz 900 MHz 1000 MHz -60 CDMA2000 Rev. 8 Adjacent Channel Offset: 1.98 MHz Integration BW: 1.228 MHz Forward Link, SRI, 9 Channels -70 400 MHz 800 MHz 900 MHz 1000 MHz -40 ACPR (dBc) -50 ACPR (dBc) 0.9 +25 C +50 C 0C 36 34 0.4 0.8 38 34 30 0.3 0.7 Psat vs. Temperature 44 Psat (dBm) P1dB (dBm) P1dB vs. Temperature 36 0.6 FREQUENCY (GHz) FREQUENCY (GHz) -80 -50 CDMA2000 Rev. 8 Adjacent Channel Offset: 885 kHz Integration BW: 1.228 MHz Forward Link, SRI, 9 Channels -60 -70 -90 -80 24 26 28 30 32 CHANNEL OUTPUT POWER (dBm) 34 36 24 26 28 30 32 34 36 CHANNEL OUTPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 1-2 HMC-C012 v03.1007 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz Input Return Loss vs. Temperature +25 C +50 C 0C -10 -15 +25 C +50 C 0C -5 RETURN LOSS (dB) -5 -10 -15 ew N r fo d e end m com e R Not 0.4 0.5 0.6 0.7 0.8 0.9 1 -25 0.3 1.1 0.4 0.5 0.6 0.7 0.8 0.9 1 0.9 1 1.1 FREQUENCY (GHz) FREQUENCY (GHz) Noise Figure vs. Temperature Reverse Isolation vs. Temperature 20 0 -10 16 +25 C +50 C 0C -20 NOISE FIGURE (dB) ISOLATION (dB) ns g i s De -20 -20 -25 0.3 Output Return Loss vs. Temperature 0 0 RETURN LOSS (dB) AMPLIFIERS 1 D E U N I T N O T C C S U I D D O PR -30 -40 -50 12 8 +25 C +50 C 0C 4 -60 -70 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 0 0.3 1.1 0.4 0.5 Absolute Maximum Ratings 0.6 0.7 0.8 1.1 FREQUENCY (GHz) FREQUENCY (GHz) Thermal Fault Indicator Characteristics Supply Voltage (VIN) +13 Vdc RF Input Power (RFIN) +10 dBm IOUT (VOUT > 2V) Storage Temperature -40 to +85 °C RON (I OUT = 50 mA) Operating Temperature 0 to +50 °C ROFF (VOUT = 30 V) Thermal Fault Indicator Max Pdiss (derate 1.8 mW/°C above 50 °C) 180 mW Enable -0.5 to +6.0 Vdc Parameter Min. Typ. Max. Units 7.5 Ohms 350 mA 1 MOhm Enable Input Characteristics Parameter ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS VIH VIL IIL @ VIN = 0V IIH @ 5V 1-3 Min. Typ. Max. Units 1.6 V 3.5 V -0.5 mA < ± 50 μA For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C012 v03.1007 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz Recommended Biasing Procedure TURN-ON 1. Connect RF input and output 2. Apply Supply Voltage VIN (+12 Vdc) 3. Set Enable low 4. Apply RF input signal TURN-OFF 1. Remove RF input signal 2. Remove Supply Voltage VIN Pin Descriptions ew N r fo d e end m com e R Not Pin Number Function Description 1 RFIN & RF Ground RF input connector, SMA female. This pin is AC coupled and matched to 50 Ohms. 2 VIN Power supply voltage for the amplifier. 3 GND Power supply ground. 4 RFOUT & RF Ground RF output connector, SMA female. This pin is AC coupled and matched to 50 Ohms. 5 GND Ground for thermal fault indicator and enable circuit. 6 Thermal Fault Indicator Open drain output. High impedance for base plate temperatures less than 55 °C. Low impedance for base plate temperatures exceeding 75 °C. ns g i s De 1 AMPLIFIERS D E U N I T N O T C C S U I D D O PR Interface Schematic TTL compatible supply voltage (VIN) shutdown. If enable feature is not required, short this pin to DC ground. 7 Enable TTL “High” Disable TTL “Low” Enable For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 1-4 HMC-C012 v03.1007 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz AMPLIFIERS 1 D E U N I T N O T C C S U I D D O PR Outline Drawing ew N r fo d e end m com e R Not ns g i s De Package Information Package Type C-7 Package Weight [1] 740 gms [2] Spacer Weight N/A [1] Includes the connectors [2] ±10% Tolerance NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH a. COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 b. BASE, TIN 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X±.1 (2.54mm) .XX±.02 (0.50mm) 6. DRAWING TO CHANGE AS REQUIRED. 7. BASE MUST BE GROUNDED AND MOUNTED TO HEAT SINK CAPABLE OF DISSIPATING 100W (65 °C) 1-5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C012 v03.1007 10 WATT POWER AMPLIFIER MODULE, 400 - 1000 MHz HMC-C012 Heatsink/Fan Outline Drawing ew N r fo d e end m com e R Not ns g i s De 1 AMPLIFIERS D E U N I T N O T C C S U I D D O PR NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH: COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X±.1 (2.54mm) .XX±.02 (0.50mm) HMC-C008 Ordering Information Part Number Description HMC-C012 10 Watt Power Amplifier Module, 400 - 1000 MHz HMC-C012HV115 10 Watt Power Amplifier Module with heat sink, 115 Vac fan and power cord. HMC-C012HV230 10 Watt Power Amplifier Module with heat sink, 230 Vac fan and power cord. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 1-6