FERF1601G-FERF1608G Isolated 16.0AMP.Glass Passivated High Efficient Rectifiers ITO-220AB Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability For use in low voltage, high frequency inventor, free wheeling, and polarity protection application. Mechanical Data Cases: ITO-220AB molded plastic Epoxy: UL 94V0 rate flame retardant Polarity: As marked High temperature soldering guaranteed: o 260 C/ 0.25” (6.35mm) from case for 10 seconds Mounting torque: 5 in – 1bs. max. Weight: 2.24 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current o @TC =100 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @8.0A Maximum DC Reverse Current o @T A=25 C at Rated DC Blocking Voltage @ T A=125 oC V RRM V RMS V DC 200 140 200 300 210 300 400 280 400 600 420 600 800 1000 560 700 800 1000 IFSM 125 A VF 1.0 1.3 IR Cj R θJC TJ 1.7 10 400 50 80 80 50 1.5 -65 to +150 -65 to +150 Storage Temperature Range TSTG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. 3. Mounted on Heatsink Size of 4 in x 6 in x 0.25 in Al-Plate. http://www.luguang.cn V V V A Trr Operating Temperature Range 100 70 100 16 Typical Junction Capacitance Typical Thermal Resistance (Note 3) 50 35 50 Units I(AV) Typical Reverse Recovery Time ( Note 1 ) ( Note 2 ) HERF HERF HERF HERF HERF HERF HERF HERF 1601G 1602G 1603G 1604G 1605G 1606G 1607G 1608G mail:[email protected] V uA uA nS pF o C/W o C o C FERF1601G-FERF1608G Isolated 16.0AMP.Glass Passivated High Efficient Rectifiers FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1000 20 12 8 4 0 0 50 100 150 o FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 150 Tj=25 0C 120 Tj=25 0C 1 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 60 FIG.5- TYPICAL FORWARD CHARACTERISTICS PER LEG 100 200 Tj=25 0C 160 HE RF 16 01 G~ HE 80 HE RF RF 16 160 05 6G G ~ HE 40 RF 160 8G 0 1 2 5 10 20 120 G 05 16 RF HE 3.0 1.0 8G 10 60 FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 240 30 F1 100 ER 50 ~H 20 6G 10 60 5 F1 2 ER 0 1 0.3 H 30 NUMBER OF CYCLES AT 60Hz CAPACITANCE.(pF) 10 0.1 0 8.3ms Single Half Sine Wave JEDEC Method 90 Tj=125 0C 100 HE RF 16 01 G~ HE RF 16 04 G PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) INSTANTANEOUS REVERSE CURRENT. ( A) 16 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) RATINGS AND CHARACTERISTIC CURVES (HERF1601G THRU HERF1608G) 0.1 0.03 50 100 200 500 1000 0 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.8