UNSHIELDED RADIAL POWER INDUCTOR Industries P11R20875 SERIES • Low cost, high current • Inductance range from 10 - 10,000 µH • Open construction • Optional inductance tolerance: K = ±10% (add suffix letter for tolerance after the part number) • Operating temperature range: -40oC to +85oC • RoHS compliant product ELECTRICAL SPECIFICATION @ 25OC Part Number P11R20875- Inductance (µH) (±20%) DCR (Ω) (Max) RATED IDC (A) 100 10 0.05 2.90 120 12 0.06 2.50 150 15 0.07 2.20 180 18 0.08 1.90 220 22 0.09 1.80 270 27 0.11 1.70 330 33 0.13 1.50 390 39 0.14 1.30 470 47 0.15 1.30 560 56 0.18 1.20 680 68 0.20 1.10 820 82 0.24 1.00 101 100 0.35 0.89 121 120 0.36 0.81 151 150 0.42 0.72 181 180 0.57 0.66 221 220 0.63 0.57 271 270 0.88 0.51 331 330 1.05 0.46 391 390 1.17 0.44 471 470 1.34 0.41 561 560 1.72 0.36 681 680 1.96 0.33 821 820 2.56 0.30 102 1000 2.94 0.27 • Inductance measured: 1KHz, 0.30VRMS • IRATED: Max 10% inductance drop and ΔT=40°C Temp Rise Product performance is limited to specified parameters. Data is subject to change without prior notice. 13200 Estrella Ave., Bldg. B Gardena, CA 90248 Tel: 310-325-1043 Fax: 310-325-1044 Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 www.mpsind.com [email protected] UNSHIELDED RADIAL POWER INDUCTOR Industries P11R20875 SERIES ELECTRICAL SPECIFICATION @ 25OC Part Number P11R20875- Inductance (µH) (±20%) DCR (Ω) (Max) RATED IDC (A) 122 1200 4.04 0.24 152 1500 4.70 0.22 182 1800 5.05 0.20 222 2200 6.25 0.18 272 2700 8.72 0.16 332 3300 10.6 0.15 392 3900 14.2 0.14 472 4700 16.7 0.12 562 5600 18.7 0.11 682 6800 21.8 0.10 822 8200 28.7 0.093 103 10000 33.0 0.084 • Inductance measured: 1KHz, 0.30VRMS • IRATED: Max 10% inductance drop and ΔT=40°C Temp Rise DIMENSIONS Product performance is limited to specified parameters. Data is subject to change without prior notice. 13200 Estrella Ave., Bldg. B Gardena, CA 90248 Tel: 310-325-1043 Fax: 310-325-1044 A = 8.3 max mm B = 7.5 max mm C = 20.0 ± 2.0 mm E = 5.0 ± 0.5 mm F = 0.6 ± 0.1 mm Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 www.mpsind.com [email protected]