FERRITE SHIELDED RADIAL POWER INDUCTORS P11RS2875 SERIES • Ferrite shielded radial power inductor • Ideal for power line filtering in switching power supply and other low to medium current applications • Compact size: 8.3mm diameter x 7.5mm height • Inductance tolerance: M = ±20% • Operating temperature range: -40°C to +85°C • RoHS compliant product ELECTRICAL PARAMETERS @ 25°C Part Number DCR (Ω MAX) P11RS2875- Inductance (μH) (±20%) Rated Idc (A) Rated Irms (A) 100M 10 0.047 3.60 2.95 120M 12 0.055 3.20 2.70 150M 15 0.068 2.96 2.25 180M 18 0.083 2.72 2.10 220M 22 0.097 2.48 2.00 270M 27 0.130 2.08 1.75 330M 33 0.140 2.00 1.70 390M 39 0.170 1.68 1.50 470M 47 0.210 1.60 1.32 560M 56 0.230 1.44 1.11 680M 68 0.280 1.36 1.00 820M 82 0.400 1.28 0.92 101M 100 0.450 1.12 0.84 121M 120 0.50 1.04 0.80 151M 150 0.63 0.96 0.72 181M 180 0.68 0.88 0.70 221M 220 0.91 0.75 0.53 271M 270 1.00 0.70 0.51 331M 330 1.20 0.65 0.44 391M 390 1.30 0.56 0.42 471M 470 1.70 0.53 0.37 561M 560 2.10 0.42 0.33 681M 680 2.30 0.41 0.31 821M 820 3.10 0.38 0.28 102M 1000 3.90 0.35 0.24 Note: 1. Inductance measured: 1KHz, 1.0Vrms 2. Idc: 10% inductance drop typical from initial value 3. Irms: ΔT ≤ 40°C Temp Rise at rated current Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 www.mpsind.com [email protected] FERRITE SHIELDED RADIAL POWER INDUCTORS P11RS2875 SERIES ELECTRICAL PARAMETERS @ 25°C Part Number DCR (Ω MAX) P11RS2875- Inductance (μH) (±20%) Rated Idc (A) Rated Irms (A) 122M 1200 4.30 0.33 0.22 152M 1500 5.80 0.27 0.18 182M 1800 7.10 0.26 0.17 222M 2200 7.9 0.24 0.16 272M 2700 11.0 0.20 0.14 332M 3300 12.0 0.18 0.13 392M 3900 16.1 0.17 0.12 472M 4700 18.1 0.16 0.11 562M 5600 25.4 0.14 0.10 682M 6800 28.8 0.13 0.09 822M 8200 41.8 0.12 0.08 103M 10000 46.8 0.11 0.07 Note: 1. Inductance measured: 1KHz, 1.0Vrms 2. Idc: 10% inductance drop typical from initial value 3. Irms: ΔT ≤ 40°C Temp Rise at rated current DIMENSIONS (mm) A = 8.3 Max B = 7.5 Max C = 5.0±1.0 Min E = 5,0±0,5 F = 0,60 Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.010 .XXX : ±0.003 mm: X,X : ±0,254 X,XX : ±0,076 www.mpsind.com [email protected]