TI TS5A2053YEPR

W www.ti.com
SCDS183 – JANUARY 2005
Description
Features
The TS5A2053 is a single-pole double-throw (SPDT)
analog switch that is designed to operate from 1.65 V
to 5.5 V. This device can handle both digital and analog
signals, and signals up to V+ can be transmitted in either
direction.
Applications
D Cell Phones
D Portable Audio Video Equipment
D Battery-Powered Equipment
D Low-Voltage Data Acquisition Systems
D Test Equipment
D Communication Circuits
D Low ON-State Resistance (10 W)
D Control Inputs Are 5-V Tolerant
D Low Charge Injection
D Excellent ON-Resistance Matching
D Low Total Harmonic Distortion (THD)
D 1.65-V to 5.5-V Single-Supply Operation
D Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
D ESD Performance Tested Per JESD 22
− 2000-V Human-Body Model
(A114-B, Class II)
− 1000-V Charged-Device Model (C101)
SSOP OR VSSOP PACKAGE
(TOP VIEW)
8 V
+
COM 1
EN 2
7
NC
GND 3
6
NO
5
IN
Logic Control
GND 4
Summary of Characteristics
V+ = 5 V and TA = 25 °C
Single Pole
Double Throw
(SPDT)
Configuration
YEP OR YZP PACKAGE
(BOTTOM VIEW)
GND 4
GND
Logic Control
3
5
6
EN 2
7
Number of channels
7.5 Ω
IN
ON-state resistance match (∆ron)
0.8 Ω
NO
ON-state resistance flatness (ron(flat))
NC
Turn-on/turn-off time (tON/tOFF)
Charge injection (QC)
8 V
+
COM 1
1
ON-state resistance (ron)
Bandwidth (BW)
FUNCTION TABLE
EN
IN
NC TO COM,
COM TO NC
NO TO COM,
COM TO NO
L
L
ON
OFF
L
H
OFF
ON
H
X
OFF
OFF
1.7 Ω
6.8 ns/4.1 ns
3 pC
330 MHz
OFF isolation (OISO)
−64 dB at 10 MHz
Crosstalk (XTALK)
−68 dB at 10 MHz
Total harmonic distortion (THD)
0.01%
Leakage current (ICOM(OFF))
±10 nA
Power-supply current (I+)
Package option
0.1 µA
8-pin DSBGA, SSOP, or
VSSOP
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
! "#$ ! %#&'" ($) (#"!
" !%$""! %$ *$ $! $+! !#$! !(( ,-)
(#" %"$!!. ($! $"$!!'- "'#($ $!. '' %$$!)
Copyright  2005, Texas Instruments Incorporated
W www.ti.com
SCDS183 – JANUARY 2005
ORDERING INFORMATION
PACKAGE(1)
TA
ORDERABLE PART NUMBER
NanoStar − WCSP (DSBGA)
0.23-mm Large Bump − YEP
−40°C to 85°C
NanoFree − WCSP (DSBGA)
0.23-mm Large Bump − YZP (Pb-free)
TOP-SIDE MARKING(2)
TS5A2053YEPR
Tape and reel
TS5A2053YZPR
SSOP − DCT
Tape and reel
TS5A2053DCTR
JAF_ _ _
VSSOP − DCU
Tape and reel
TS5A2053DCUR
JAF_
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.
(2) DCT: The actual top-side marking has three additional characters that designate the year, month, and assembly/test site.
DCU: The actual top-side marking has one additional character that designates the assembly/test site.
YEP/YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following character
to designate the assembly/test site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free).
Absolute Minimum and Maximum Ratings(1)(2)
over operating free-air temperature range (unless otherwise noted)
V+
VNO
VNC
VCOM
IK
INO
INC
ICOM
VI
MIN
MAX
Supply voltage range(3)
UNIT
−0.5
6.5
V
Analog voltage range(3)(4)(5)
−0.5
V+ + 0.5
V
Analog port diode current
VNC, VNO, VCOM < 0 or VNO, VNC, VCOM > V+
−50
50
mA
On-state switch current
VNC, VNO, VCOM = 0 to V+
−50
50
mA
−0.5
6.5
V
Digital input voltage range(3)(4)
IIK
I+
Digital input clamp current
IGND
Continuous current through GND
θJA
Package thermal impedance(6)
VI < 0
−50
Continuous current through V+
mA
100
−100
mA
mA
DCT package
220
DCU package
227
YEP/YZP package
102
°C/W
C/W
Tstg
Storage temperature range
−65
150
°C
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade
device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified
is not implied.
(2) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
(3) All voltages are with respect to ground, unless otherwise specified.
(4) The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
(5) This value is limited to 5.5 V maximum.
(6) The package thermal impedance is calculated in accordance with JESD 51-7.
2
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 5-V Supply(1)
V+ = 4.5 V to 5.5 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
TA
V+
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal range
VCOM,
VNO, VNC
ON-state resistance
ron
ON-state resistance
match between
channels
∆ron
ON-state resistance
flatness
ron(flat)
NO, NC
OFF leakage current
COM
OFF leakage current
NO, NC
ON leakage current
COM
ON leakage current
0
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −32 mA,
Switch ON,
See Figure 13
25°C
VNO or VNC = 3.15 V,
ICOM = −32 mA,
Switch ON,
See Figure 13
25°C
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −32 mA,
Switch ON,
See Figure 13
25°C
INO(OFF),
INC(OFF)
VNO or VNC = 1 V,
VCOM = 4.5 V,
or
VNO or VNC = 4.5 V,
VCOM = 1 V,
Switch OFF,
See Figure 14
ICOM(OFF)
VCOM = 1 V,
VNO or VNC = 4.5 V,
or
VCOM = 4.5 V,
VNO or VNC = 1 V,
Switch OFF,
See Figure 14
INO(ON),
INC(ON)
VNO = 1 V, VCOM = Open,
or
VNO = 4.5 V, VCOM = Open,
Switch ON,
See Figure 15
ICOM(ON)
VCOM = 1 V,
VNO or VNC = Open,
or
VCOM = 4.5 V,
VNO or VNC = Open,
Switch ON,
See Figure 15
Full
V+
7.5
4.5 V
13.8
16
0.8
Full
4.5
1.7
4.5 V
25°C
2
4.5
−20
5
25°C
−10
20
−1
10
5.5 V
Full
nA
−10
10
−10
5.5 V
25°C
Ω
nA
−20
25°C
Ω
20
5.5 V
Full
Full
Ω
3
4.5 V
Full
V
5.5
−20
10
20
−5
−1
nA
5
5.5 V
nA
Full
−10
10
Full
5.5
V
Full
V+ × 0.7
0
−0.1
V+ × 0.3
0.1
V
25°C
Digital Control Inputs (IN, EN)
Input logic high
Input logic low
Input leakage
current
VIH
VIL
IIH, IIL
VI = 5.5 V or 0
Full
5.5 V
0.05
−1
1
µA
A
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
3
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 5-V Supply(1) (continued)
V+ = 4.5 V to 5.5 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
3.8
5.3
6.8
UNIT
Dynamic
Turn-on time
VCOM = 3 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
5V
tON
Full
4.5 V to 5.5 V
Turn-off time
VCOM = 3 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
5V
0.8
tOFF
Full
4.5 V to 5.5 V
0.4
25°C
5V
3
pC
25°C
5V
6
pF
See Figure 16
25°C
5V
9.5
pF
VNO or VNC = V+ or GND,
See Figure 16
Switch ON,
25°C
5V
18
pF
See Figure 16
25°C
5V
18
pF
NO, NC
OFF capacitance
VGEN = 0,
CL = 0.1 nF,
RGEN = 0,
See Figure 21
CNO(OFF), VNO or VNC = V+ or GND,
See Figure 16
CNC(OFF) Switch OFF,
COM
OFF capacitance
VCOM = V+ or GND,
CCOM(OFF)
Switch OFF,
NO, NC
ON capacitance
CNO(ON),
CNC(ON)
COM
ON capacitance
VCOM = V+ or GND,
CCOM(ON)
Switch ON,
Charge injection
QC
3
7.1
1.9
ns
4.1
4.5
ns
Digital input
capacitance
CI
VI = V+ or GND,
See Figure 16
25°C
5V
2.5
pF
Bandwidth
BW
RL = 50 Ω,
Switch ON,
See Figure 18
25°C
5V
330
MHz
OFF isolation
OISO
RL = 50 Ω,
f = 10 MHz,
Switch OFF,
See Figure 19
25°C
5V
−64
dB
Crosstalk
XTALK
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 20
25°C
5V
−68
dB
THD
RL = 600 Ω,
CL = 50 pF,
f = 20 Hz to 20 kHz,
See Figure 22
25°C
5V
0.01
%
Total harmonic
distortion
Supply
25°C
Positive supply
I+
VI = V+ or GND,
Switch ON or OFF
5.5 V
current
Full
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
4
0.1
1
5
µA
A
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 3.3-V Supply(1)
V+ = 3 V to 3.6 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal range
ON-state
resistance
VCOM,
VNO,
VNC
ron
ON-state
resistance match
between channels
∆ron
ON-state
resistance flatness
ron(flat)
0
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −24 mA,
Switch ON,
See Figure 13
25°C
VNO or VNC = 2.1 V,
ICOM = −24 mA,
Switch ON,
See Figure 13
25°C
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −24 mA,
Switch ON,
See Figure 13
25°C
Full
V+
13.2
3V
13.8
16
1
5.5
Full
NO, NC
OFF leakage
current
INO(OFF),
INC(OFF)
VNO or VNC = 1 V, VCOM = 3 V,
or
VNO or VNC = 3 V, VCOM = 1 V,
Switch OFF,
See Figure 14
25°C
COM
OFF leakage
current
VCOM = 1 V, VNO or VNC = 3 V,
or
VCOM = 3 V, VNO or VNC = 1 V,
Switch OFF,
See Figure 14
25°C
ICOM(OFF)
NO, NC
ON leakage current
INO(ON),
INC(ON)
VNO or VNC = 1 V, VCOM = Open,
or
VNO or VNC = 3 V, VCOM = Open,
Switch ON,
See Figure 15
25°C
COM
ON leakage current
VCOM = 1 V, VNO or VNC = Open,
or
VCOM = 3 V, VNO or VNC = Open,
Switch ON,
See Figure 15
25°C
ICOM(ON)
5.3
3V
7
11
−20
4
20
−10
−1
10
3.6 V
Full
Full
nA
−10
10
−10
3.6 V
4.5
−20
10
20
−5
3.6 V
Ω
nA
−20
Full
Ω
20
3.6 V
Full
Ω
3
3V
Full
V
−1
nA
5
nA
−10
10
5.5
V
Full
V+ × 0.7
0
−0.1
V+ × 0.3
0.1
V
25°C
Digital Control Inputs (IN, EN)
Input logic high
Input logic low
Input leakage
current
VIH
VIL
IIH, IIL
Full
VI = 5.5 V or 0
Full
3.6 V
0.05
−1
1
µA
A
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
5
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 3.3-V Supply(1) (continued)
V+ = 3 V to 3.6 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
5
6.4
7.9
UNIT
Dynamic
Turn-on time
VCOM = 2 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
3.3 V
tON
Full
3 V to 3.6 V
4.5
Turn-off time
VCOM = 2 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
3.3 V
1.1
tOFF
Full
3 V to 3.6 V
0.3
CL = 0.1 nF,
See Figure 21
25°C
3.3 V
1
pC
See Figure 16
25°C
3.3 V
6
pF
8.2
2.4
ns
4.7
5
ns
Charge injection
QC
NO, NC
OFF capacitance
CNO(OFF)
VGEN = 0,
RGEN = 0,
VNO or VNC = V+ or GND,
Switch OFF,
COM
OFF capacitance
CCOM(OFF)
VCOM = V+ or GND,
Switch OFF,
See Figure 16
25°C
3.3 V
9.5
pF
NO, NC
ON capacitance
CNO(ON)
VNO or VNC = V+ or GND,
Switch ON,
See Figure 16
25°C
3.3 V
18.5
pF
COM
ON capacitance
CCOM(ON)
VCOM = V+ or GND,
Switch ON,
See Figure 16
25°C
3.3 V
18.5
pF
VI = V+ or GND,
See Figure 16
25°C
3.3 V
3
pF
BW
RL = 50 Ω,
Switch ON,
See Figure 18
25°C
3.3 V
320
MHz
OISO
RL = 50 Ω,
f = 10 MHz,
Switch OFF,
See Figure 19
25°C
3.3 V
−64
dB
XTALK
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 20
25 °C
3.3 V
−68
dB
THD
RL = 600 Ω,
CL = 50 pF,
f = 20 Hz to 20 kHz,
See Figure 22
25°C
3.3 V
0.035
%
Digital input
capacitance
Bandwidth
OFF isolation
Crosstalk
Total harmonic
distortion
CI
Supply
25°C
Positive supply
I+
VI = V+ or GND,
Switch ON or OFF
3.6 V
current
Full
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
6
0.1
1
5
µA
A
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 2.5-V Supply(1)
V+ = 2.3 V to 2.7 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
TA
V+
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal range
VCOM,
VNO,
VNC
ON-state resistance
ron
ON-state resistance
match between
channels
∆ron
ON-state resistance
flatness
ron(flat)
NO, NC
OFF leakage current
COM
OFF leakage current
NO, NC
ON leakage current
COM
ON leakage current
0
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −8 mA,
Switch ON,
See Figure 13
25°C
VNO or VNC = 1.6 V,
ICOM = −8 mA,
Switch ON,
See Figure 13
25°C
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −8 mA,
Switch ON,
See Figure 13
25°C
INO(OFF),
INC(OFF)
VNO or VNC = 0.5 V,
VCOM = 2.2 V,
or
VNO or VNC = 2.2 V,
VCOM = 0.5 V,
Switch OFF,
See Figure 14
ICOM(OFF)
VCOM = 0.5 V,
VNO or VNC = 2.2 V,
or
VCOM = 2.2 V,
VNO or VNC = 0.5 V,
Switch OFF,
See Figure 14
INO(ON),
INC(ON)
VNO or VNC = 0.5 V,
VCOM = Open,
or
VNO or VNC = 2.2 V,
VCOM = Open,
Switch ON,
See Figure 15
ICOM(ON)
VCOM = 0.5 V,
VNO or VNC = Open,
or
VCOM = 2.2 V,
VNO or VNC = Open,
Switch ON,
See Figure 15
Full
V+
20
2.3 V
28
30
1.1
6
Full
15
2.3 V
25°C
16
20
−20
3.5
20
−10
−2
10
2.7 V
Full
nA
−10
25°C
10
−10
4
10
2.7 V
nA
−20
Full
25°C
Ω
nA
−20
25°C
Ω
20
2.7 V
Full
Ω
3
2.3 V
Full
V
20
−5
−2
5
2.7 V
nA
Full
−10
10
Full
5.5
V
Full
V+ × 0.7
0
−0.1
V+ × 0.3
0.1
V
25°C
Digital Control Inputs (IN, EN)
Input logic high
Input logic low
Input leakage
current
VIH
VIL
IIH, IIL
VI = 5.5 V or 0
Full
2.7 V
0.05
−1
1
µA
A
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
7
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 2.5-V Supply(1) (continued)
V+ = 2.3 V to 2.7 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
7.1
9.3
UNIT
Dynamic
Turn-on time
VCOM = 1.5 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
2.5 V
5.9
tON
Full
2.3 V to 2.7 V
5.1
Turn-off time
VCOM = 1.5 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
2.5 V
2.1
tOFF
Full
2.3 V to 2.7 V
1.2
CL = 0.1 nF,
See Figure 21
25°C
2.5 V
0.5
pC
See Figure 16
25°C
2.5 V
6.5
pF
10
3.2
ns
5.1
5.2
ns
Charge injection
QC
NO, NC
OFF capacitance
CNO(OFF)
CNC(OFF)
VGEN = 0,
RGEN = 0
VNO or VNC = V+ or GND,
Switch OFF,
COM
OFF capacitance
CCOM(OFF)
VCOM = V+ or GND,
Switch OFF,
See Figure 16
25°C
2.5 V
10
pF
NO, NC
ON capacitance
CNO(ON)
CNC(ON)
VNO or VNC = V+ or GND,
Switch ON,
See Figure 16
25°C
2.5 V
18.5
pF
COM
ON capacitance
CCOM(ON)
VCOM = V+ or GND,
Switch ON,
See Figure 16
25°C
2.5 V
18.5
pF
VI = V+ or GND,
See Figure 16
25°C
2.5 V
3
pF
BW
RL = 50 Ω,
Switch ON,
See Figure 18
25°C
2.5 V
320
MHz
OISO
RL = 50 Ω,
f = 10 MHz,
Switch OFF,
See Figure 19
25°C
2.5 V
−64
dB
XTALK
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 20
25 °C
2.5 V
−68
dB
THD
RL = 600 Ω,
CL = 50 pF,
f = 20 Hz to 20 kHz,
See Figure 22
25°C
2.5 V
0.26
%
Digital input
capacitance
Bandwidth
OFF isolation
Crosstalk
Total harmonic
distortion
CI
Supply
25°C
Positive supply
I+
VI = V+ or GND,
Switch ON or OFF
2.7 V
current
Full
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
8
0.1
1
5
µA
A
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 1.8-V Supply(1)
V+ = 1.65 V to 1.95 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
TA
V+
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal range
ON-state
resistance
VCOM,
VNO, VNC
ron
ON-state
resistance match
between channels
∆ron
ON-state
resistance flatness
ron(flat)
0
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −4 mA,
Switch ON,
See Figure 13
25°C
VNO or VNC = 1.15 V,
ICOM = −4 mA,
Switch ON,
See Figure 13
25°C
0 ≤ (VNO or VNC) ≤ V+,
ICOM = −4 mA,
Switch ON,
See Figure 13
25°C
Switch OFF,
See Figure 14
NO, NC
OFF leakage
current
INO(OFF),
INC(OFF)
VNO or VNC = 0.3 V,
VCOM = 1.65 V,
or
VNO or VNC = 1.65 V,
VCOM = 0.3 V,
COM
OFF leakage
current
ICOM(OFF)
VCOM = 0.3 V, VNO = 1.65 V, Switch OFF,
or
See Figure 14
VCOM = 1.65 V, VNO = 0.3 V,
NO, NC
ON leakage current
INO(ON),
INC(ON)
VNO or VNC = 0.3 V,
VCOM = Open,
or
VNO or VNC = 1.65 V,
VCOM = Open,
Switch ON,
See Figure 15
ICOM(ON)
VCOM = 0.3 V,
VNO or VNC = Open,
or
VCOM = 1.65 V,
VNO or VNC = Open,
Switch ON,
See Figure 15
COM
ON leakage current
Full
V+
85
1.65 V
90
105
2
Full
7.5
76
1.65 V
25°C
85
100
−20
3.5
20
−10
1
10
1.95 V
Full
−1
25°C
1
−10
4
µA
A
20
25°C
µA
A
10
1.95 V
Full
Ω
µA
A
−20
25°C
Ω
20
1.95 V
Full
Ω
4
1.65 V
Full
V
20
−5
1
5
µA
A
1.95 V
Full
−10
Full
Full
V+ × 0.65
0
25°C
10
Digital Control Inputs (IN, EN)
Input logic high
Input logic low
Input leakage
current
VIH
VIL
IIH, IIL
VI = 5.5 V or 0
Full
1.95 V
5.5
V
V
−0.1
V+ × 0.35
0.05
0.1
−1
1
µA
A
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
9
W www.ti.com
SCDS183 – JANUARY 2005
Electrical Characteristics for 1.8-V Supply(1) (continued)
V+ = 1.65 V to 1.95 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
11.8
14.5
UNIT
Dynamic
Turn-on time
VCOM = 1.3 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
1.8 V
10.2
tON
Full
1.65 V to 1.95 V
8.4
Turn-off time
VCOM = 1.3 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
1.8 V
2.9
tOFF
Full
1.65 V to 1.95 V
2.2
CL = 0.1 nF,
See Figure 21
25°C
1.8 V
0.5
pC
See Figure 16
25°C
1.8 V
6.5
pF
15.5
4.3
ns
6.5
7
ns
NO, NC
OFF capacitance
VGEN = 0,
RGEN = 0
CNO(OFF), VNO or VNC = V+ or GND,
CNC(OFF) Switch OFF,
COM
OFF capacitance
VCOM = V+ or GND,
CCOM(OFF)
Switch OFF,
See Figure 16
25°C
1.8 V
10
pF
NO, NC
ON capacitance
CNO(ON),
CNC(ON)
See Figure 16
25°C
1.8 V
19
pF
COM
ON capacitance
VCOM = V+ or GND,
CCOM(ON)
Switch ON,
See Figure 16
25°C
1.8 V
14
pF
VI = V+ or GND,
See Figure 16
25°C
1.8 V
3
pF
BW
RL = 50 Ω,
Switch ON,
See Figure 18
25°C
1.8 V
320
MHz
OISO
RL = 50 Ω,
f = 10 MHz,
Switch OFF,
See Figure 19
25°C
1.8 V
−64
dB
XTALK
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 20
25 °C
1.8 V
−68
dB
THD
RL = 10 kΩ,
CL = 50 pF,
f = 20 Hz to 20 kHz,
See Figure 22
25°C
1.8 V
2.6
%
Charge injection
Digital input
capacitance
Bandwidth
OFF isolation
Crosstalk
Total harmonic
distortion
QC
CI
VNO or VNC = V+ or GND,
Switch ON,
Supply
25°C
Positive supply
I+
VI = V+ or GND,
Switch ON or OFF
1.95 V
current
Full
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
10
0.1
1
5
µA
A
W www.ti.com
SCDS183 – JANUARY 2005
100
90
80
70
60
50
40
30
20
10
0
0
Figure 1
TA = 25°C
25
TA = 25°C
20
NO > COM
ron (W)
ron (Ω)
TYPICAL PERFORMANCE
NO > COM
15
10
NC > COM
5
NC > COM
0
0.25
0.5
0.75
1
1.25
VCOM (V)
1.5
1.75
0.6
0.9
1.2
1.5
1.8
2.1
2.4
Figure 1B. ron vs VCOM (V+ = 2.3 V)
14
12
0.3
VCOM (V)
Figure 1A. ron vs VCOM (V+ = 1.65 V)
TA = 25°C
0
10
TA = 25°C
9
NO > COM
NO > COM
8
10
7
ron (W)
ron (W)
NC > COM
8
6
6
5
NC > COM
4
3
4
2
2
NO > COM
1
NC > COM
0
0
0
0.5
1
1.5
2
VCOM (V)
2.5
0
3
12
TA = −40°C
TA = 25°C
TA = 85°C
2
2.5
3
3.5
4
4.5
TA = −40°C
TA = 25°C
TA = 85°C
10
ron (W)
12
ron (W)
1.5
Figure 1D. ron vs VCOM (V+ = 4.5 V)
18
14
1
VCOM (V)
Figure 1C. ron vs VCOM (V+ = 3 V)
16
0.5
10
8
6
8
6
4
4
NO > COM
2
NO > COM
2
NC > COM
NC > COM
0
0
0.5
1
1.5
2
2.5
VCOM (V)
Figure 2. ron vs VCOM (V+ = 3 V)
3
0
0
0.5
1
1.5
2
2.5
3
VCOM (V)
3.5
4
4.5
Figure 3. ron vs VCOM (V+ = 4.5 V)
11
W www.ti.com
SCDS183 – JANUARY 2005
0.5
18
16
12
10
8
0.0
6
4
−0.5
−1.0
−1.5
−2.5
VCC = 5 V
−3.0
2
−3.5
0
−40°C
25°C
TA (5C)
0
85°C
Figure 4. Leakage Current vs Temperature
(V+ = 5.5 V)
6
12
5
tON/tOFF (ns)
10
8
tON
6
4
1
tOFF
0
1.65
6
tON
4
3
tOFF
2
0
2.3
2.95
3.6
4.25
4.9
5.55
−40°C
25°C
Supply Voltage (V)
Figure 7. tON and tOFF vs Temperature (V+ = 5 V)
3.5
3
85°C
TA (5C)
Figure 6. tON and tOFF vs V+
0
0
TA = 255C
Gain
−1
−10
−2
−20
2.5
Gain (dB)
Logic Threshold (V)
5
1
2
2
VIL
1.5
1
VIH
0.5
0
1.6
2.1
2.6
3.1
3.6
4.1
4.6
5.1
V+ (V)
Figure 8. Logic Threshold vs V+
12
2
3
4
Bias Voltage (V)
Figure 5. Charge Injection (QC) vs VCOM
14
tON/tOFF (ns)
VCC = 3.3 V
−2.0
5.6
Phase
−3
−30
−4
−40
−5
−50
−6
−60
0.1
1
10
100
Frequency (MHz)
Figure 9. Bandwidth (V+ = 5 V)
1000
Phase
Leakage (nA)
14
Charge Injection (pC)
INO(OFF)/ICOM(OFF)
INO(OFF),COMHI/INC(OFF)
INC(OFF),COMHI
INC(ON)
ICOM(ON)
INO(ON)
ICOM(ON),com>NO
W www.ti.com
0.05
−50
−60
−70
−80
−90
−100
0.1
THD + Noise (%)
0
−10
−20
−30
−40
0.04
0.03
3.3 V
0.02
0.01
5V
0
1
10
100
Frequency (MHz)
Figure 10. OFF Isolation (V+ = 5 V)
100K
1000
1M
10M
100M
100M
Frequency (MHz)
Figure 11. Total Harmonic Distortion vs Frequency
7
6
5
ICC (nA)
Gain (dB)
SCDS183 – JANUARY 2005
ICCL
4
3
2
ICCH
1
0
−40°C
25°C
TA (5C)
85°C
Figure 12. Power-Supply Current vs Temperature
(V+ = 5 V)
13
W www.ti.com
SCDS183 – JANUARY 2005
PIN DESCRIPTION
PIN
NUMBER
NAME
1
COM
DESCRIPTION
Common
2
EN
3
GND
Chip enable (active low)
Digital ground
4
GND
Digital ground
5
IN
Digital control to connect COM to NC or NO
6
NO
Normally open
7
NC
Normally close
8
V+
Power supply
PARAMETER DESCRIPTION
SYMBOL
DESCRIPTION
VCOM
Voltage at COM
VNC
Voltage at NC
VNO
Voltage at NO
ron
Resistance between COM and NC or COM and NO ports when the channel is ON
∆ron
Difference of ron between channels in a specific device
ron(flat)
Difference between the maximum and minimum value of ron in a channel over the specified range of conditions
INC(OFF)
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the OFF state
INO(OFF)
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state
INC(ON)
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the ON state and the output (COM)
open
INO(ON)
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output (COM)
open
ICOM(OFF)
Leakage current measured at the COM port, with the corresponding channel (COM to NO or COM to NC) in the OFF state and
the output (NC or NO) open
ICOM(ON)
Leakage current measured at the COM port, with the corresponding channel (COM to NO or COM to NC) in the ON state and
the output (NC or NO) open
VIH
Minimum input voltage for logic high for the control input (IN, EN)
VIL
Maximum input voltage for logic low for the control input (IN, EN)
VI
Voltage at the control input (IN, EN)
IIH, IIL
Leakage current measured at the control input (IN, EN)
tON
Turn-on time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay
between the digital control (IN) signal and analog output (COM, NC, or NO) signal when the switch is turning ON.
tOFF
Turn-off time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay
between the digital control (IN) signal and analog output (COM, NC, or NO) signal when the switch is turning OFF.
QC
Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NC, NO, or COM)
output. This is measured in coulomb (C) and measured by the total charge induced due to switching of the control input.
Charge injection, QC = CL × ∆VCOM, CL is the load capacitance and ∆VCOM is the change in analog output voltage.
14
W www.ti.com
SCDS183 – JANUARY 2005
PARAMETER DESCRIPTION (continued)
SYMBOL
DESCRIPTION
CNC(OFF)
CNO(OFF)
Capacitance at the NC port when the corresponding channel (NC to COM) is OFF
CNC(ON)
CNO(ON)
Capacitance at the NC port when the corresponding channel (NC to COM) is ON
CCOM(OFF)
Capacitance at the COM port when the corresponding channel (COM to NC or COM to NO) is OFF
CCOM(ON)
CI
Capacitance at the COM port when the corresponding channel (COM to NC or COM to NO) is ON
Capacitance at the NO port when the corresponding channel (NO to COM) is OFF
Capacitance at the NO port when the corresponding channel (NO to COM) is ON
Capacitance of control input (IN, EN)
OISO
OFF isolation of the switch is a measurement of OFF-state switch impedance. This is measured in dB in a specific frequency,
with the corresponding channel (NC to COM or NO to COM) in the OFF state.
XTALK
Crosstalk is a measurement of unwanted signal coupling from an ON channel to an OFF channel (NC to NO or NO to NC). This
is measured in a specific frequency and in dB.
BW
Bandwidth of the switch. This is the frequency where the gain of an ON channel is −3 dB below the DC gain.
THD
Total harmonic distortion describes the signal distortion caused by the analog switch. This is defined as the ratio of root mean
square (RMS) value of the second, third, and higher harmonic to the absolute magnitude of fundamental harmonic.
I+
Static power-supply current with the control (IN, EN) pin at V+ or GND
15
W www.ti.com
SCDS183 – JANUARY 2005
PARAMETER MEASUREMENT INFORMATION
V+
VNC NC
COM
+
VCOM
Channel ON
VNO NO
r on +
IN or EN
VI
ICOM
VCOM * VNO or VNC
W
I COM
VI = VIH or VIL
+
GND
Figure 13. ON-State Resistance (ron)
V+
VNC NC
COM
+
VNO NO
VCOM
+
IN or EN
OFF-State Leakage Current
Channel OFF
VI = VIH or VIL
VI
+
GND
Figure 14. OFF-State Leakage Current (INC(OFF), INO(OFF), ICOM(OFF))
V+
VNC NC
+
COM
VNO NO
VCOM
ON-State Leakage Current
Channel ON
VI = VIH or VIL
IN or EN
VI
+
GND
Figure 15. ON-State Leakage Current (ICOM(ON), INC(ON), INO(ON))
16
W www.ti.com
SCDS183 – JANUARY 2005
V+
Capacitance
Meter
VNC
NC
VNO
NO
VBIAS = V+ or GND
VI = VIH or VIL
VCOM COM
VBIAS
Capacitance is measured at NC,
NO, COM, EN and IN inputs
during ON and OFF conditions.
VI
IN or EN
GND
Figure 16. Capacitance (CI, CCOM(OFF), CCOM(ON), CNC(OFF), CNO(OFF), CNC(ON), CNO(ON))
V+
TEST
RL
CL
tON
300 Ω
35 pF
tOFF
300 Ω
35 pF
NC or NO VNC or VNO
VCOM
(3)
COM
CL(2)
NC or NO
RL
IN or EN
VI
CL(2)
Logic
Input(1)
RL
GND
V+
Logic
Input
(VI)
50%
50%
0
tON
tOFF
Switch
Output
(VNC or VNO)
90%
90%
(1) All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
(2) CL includes probe and jig capacitance.
(3) See Electrical Characteristics for VCOM.
Figure 17. Turn-On (tON) and Turn-Off Time (tOFF)
V+
Network Analyzer
50 W
VNC
NC
Channel ON: NC to COM
COM
Source
Signal
VCOM
VI = V+ or GND
NO
Network Analyzer Setup
IN or EN
50 W
VI
+
Source Power = 0 dBm
(632-mV P-P at 50-W load)
GND
DC Bias = 350 mV
Figure 18. Bandwidth (BW)
17
W www.ti.com
SCDS183 – JANUARY 2005
V+
Network Analyzer
Channel OFF: NC to COM
50 W
VNC NC
VI = V+ or GND
COM
Source
Signal
50 W
VCOM
NO
Network Analyzer Setup
IN or EN
Source Power = 0 dBm
(632-mV P-P at 50-W load)
VI
50 W
+
GND
DC Bias = 350 mV
Figure 19. OFF Isolation (OISO)
V+
Network Analyzer
50 W
Channel ON: NC to COM
VNC
Channel OFF: NO to COM
NC
VCOM
Source
Signal
VNO
NO
IN or EN
+
Network Analyzer Setup
50 W
VI
50 W
VI = V+ or GND
Source Power = 0 dBm
(632-mV P-P at 50-W load)
GND
DC Bias = 350 mV
Figure 20. Crosstalk (XTALK)
V+
RGEN
VGEN
Logic
Input
(VI)
OFF
ON
OFF V
IL
NC or NO
COM
+
VIH
VCOM
∆VCOM
VCOM
NC or NO
CL(2)
VI
Logic
Input(1)
IN or EN
VGEN = 0 to V+
RGEN = 0
CL = 0.1 nF
QC = CL × ∆VCOM
VI = VIH or VIL
GND
(1) All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
(2) CL includes probe and jig capacitance.
Figure 21. Charge Injection (QC)
18
W www.ti.com
SCDS183 – JANUARY 2005
VI = VIH or VIL
RL = 600 Ω
fSOURCE = 20 Hz to 20 kHz CL = 50 pF
Channel ON: COM to NC
VSOURCE = V+ P-P
V+/2
V+
Audio Analyzer
RL
Source
Signal
10 mF
NC
10 mF
COM
600 W
600 W
NO
IN or EN
CL(1)
VI
+
600 W
GND
(1) CL includes probe and jig capacitance.
Figure 22. Total Harmonic Distortion (THD)
19
PACKAGE OPTION ADDENDUM
www.ti.com
6-Jun-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TS5A2053DCTR
ACTIVE
SM8
DCT
8
3000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-260C-UNLIM
TS5A2053DCUR
ACTIVE
US8
DCU
8
3000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-260C-UNLIM
TS5A2053DCURE4
ACTIVE
US8
DCU
8
3000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MPDS049B – MAY 1999 – REVISED OCTOBER 2002
DCT (R-PDSO-G8)
PLASTIC SMALL-OUTLINE PACKAGE
0,30
0,15
0,65
8
0,13 M
5
0,15 NOM
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
2,90
2,70
4,25
3,75
Gage Plane
PIN 1
INDEX AREA
1
0,25
4
0° – 8°
3,15
2,75
0,60
0,20
1,30 MAX
Seating Plane
0,10
0,10
0,00
NOTES: A.
B.
C.
D.
4188781/C 09/02
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion
Falls within JEDEC MO-187 variation DA.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated