TI TS3A5018DBQR

W www.ti.com
SCDS189 – JANUARY 2005
Description
The TS3A5018 is a quad single-pole double-throw
(SPDT) analog switch that is designed to operate from
2.3 V to 3.6 V. This device can handle both digital and
analog signals, and signals up to V+ can be transmitted
in either direction.
Applications
D
D
D
D
Features
D Low ON-State Resistance (10 W)
D Low Charge Injection
D Excellent ON-State Resistance Matching
D Low Total Harmonic Distortion (THD)
D 2.3-V to 3.6-V Single-Supply Operation
D Control Inputs are 5-V Tolerant
D Latch-Up Performance Exceeds 100 mA Per
Sample-and-Hold Circuit
D
Battery-Powered Equipment
Audio and Video Signal Routing
Communication Circuits
Summary of Characteristics
SOIC, SSOP, TSSOP, OR TVSOP PACKAGE
(TOP VIEW)
Logic
Control
IN 1
JESD 78, Class II
ESD Performance Tested Per JESD 22
− 2000-V Human-Body Model
(A114-B, Class II)
− 1000-V Charged-Device Model (C101)
V+ = 3.3 V, TA = 25°C
16 V+
Quad Single Pole
Double Throw
(4
SPDT)
Configuration
NC1 2
15 EN
NO1
3
14 NC4
Number of channels
COM1 4
13 NO4
ON-state resistance (ron)
4
12 COM4
ON-state resistance match (∆ron)
6
11 NC3
ON-state resistance flatness (ron(flat))
COM2 7
10 NO3
Turn-on/turn-off time (tON/tOFF)
NC2 5
NO2
Charge injection (QC)
9 COM3
GND 8
Bandwidth (BW)
FUNCTION TABLE
EN
IN
NO TO COM,
COM TO NO
NC TO COM,
COM TO NC
L
L
OFF
ON
L
H
ON
OFF
H
X
OFF
OFF
7Ω
0.3 Ω
5Ω
3.5 ns/2 ns
2 pC
300 MHz
OFF isolation (OISO)
−48 dB at 10 MHz
Crosstalk (XTALK)
−48 dB at 10 MHz
Total harmonic distortion (THD)
0.2%
Leakage current (ICOM(OFF))
±5 µA
Power-supply current (I+)
2.5 µA
Package option
16-pin SOIC, SSOP,
TSSOP, or TVSOP
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
!"# $"%&! '#( '"!
! $#!! $# )# # #* "# '' +,(
'"! $!#- '# #!#&, !&"'# #- && $##(
Copyright  2005, Texas Instruments Incorporated
W www.ti.com
SCDS189 – JANUARY 2005
ORDERING INFORMATION
PACKAGE(1)
TA
SOIC - D
SSOP (QSOP) - DBQ
−40°C to 85°C
TSSOP - PW
TVSOP - DGV
ORDERABLE PART NUMBER
Tube
TS3A5018D
Tape and reel
TS3A5018DR
Tape and reel
TS3A5018DBQR
Tube
TS3A5018PW
Tape and reel
TS3A5018PWR
Tape and reel
TS3A5018DGVR
TOP-SIDE MARKING
TS3A5018
YA018
YA018
YA018
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.
Absolute Minimum and Maximum Ratings(1)(2)
over operating free-air temperature range (unless otherwise noted)
V+
VNC,
VNO,
VCOM
IK
INC,
INO,
ICOM
VI
MIN
MAX
Supply voltage range(3)
−0.5
4.6
V
Analog voltage range(3)(4)
−0.5
7
V
Analog port diode current
VNC, VNO, VCOM < 0
−50
On-state switch current
VNC, VNO, VCOM = 0 to 7 V
−64
64
−0.5
7
Digital input voltage range(3)(4)
VI < 0
UNIT
mA
V
IIK
I+
Digital input clamp current
Continuous current through V+
−100
100
mA
IGND
Continuous current through GND
−100
100
mA
D package
θJA
Package thermal impedance(5)
−50
mA
mA
73
DBQ package
90
DGV package
120
PW package
108
°C/W
Tstg
Storage temperature range
−65
150
°C
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade
device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified
is not implied.
(2) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
(3) All voltages are with respect to ground, unless otherwise specified.
(4) The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
(5) The package thermal impedance is calculated in accordance with JESD 51-7.
2
W www.ti.com
SCDS189 – JANUARY 2005
Electrical Characteristics for 3.3-V Supply(1)
V+ = 3 V to 3.6 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal
range
VCOM,
VNC, VNO
0
25°C
0 ≤ (VNC or VNO) ≤ V+,
ICOM = −32 mA,
Switch ON,
See Figure 13
VNC or VNO = 2.1 V,
ICOM = −32 mA,
Switch ON,
See Figure 13
0 ≤ (VNC or VNO) ≤ V+,
ICOM = −32 mA,
Switch ON,
See Figure 13
25°C
VNC or VNO = 1 V, VCOM = 3 V,
or
VNC or VNO = 3 V, VCOM = 1 V,
Switch OFF,
See Figure 14
25°C
VNC or VNO = 0 to 3.6 V,
VCOM = 3.6 V to 0,
or
VNC or VNO = 3.6 V to 0,
VCOM = 0 to 3.6 V,
Switch OFF,
See Figure 14
VCOM = 1 V, VNC or VNO = 3 V,
or
VCOM = 3 V, VNC or VNO = 3 V,
Switch OFF,
See Figure 14
VCOM = 0 to 3.6 V, VNC or
VNO = 3.6 V to 0,
or
VCOM = 3.6 V to 0, VNC or
VNO = 0 to 3.6 V,
Switch OFF,
See Figure 14
VNC or VNO = 1 V, VCOM = Open,
or
VNC or VNO = 3 V, VCOM = Open,
Switch ON,
See Figure 15
25°C
VCOM = 1 V, VNC or VNO = Open,
or
VCOM = 3 V, VNC or VNO = Open,
Digital Control Inputs (IN, EN)(2)
Switch ON,
See Figure 15
25°C
ON-state
resistance
ON-state
resistance match
between
channels
ON-state
resistance
flatness
NC, NO
OFF leakage
current
COM
OFF leakage
current
ron
∆ron
ron(flat)
INC(OFF)
INO(OFF)
ICOM(OFF)
NC, NO
ON leakage
current
INC(ON)
INO(ON)
COM
ON leakage
current
ICOM(ON)
Input logic high
Input logic low
VIH
VIL
Input leakage
current
IIH, IIL
Full
7
3V
10
12
25°C
0.3
Ω
Ω
1
Full
5
7
3V
Full
Full
V
0.8
3V
8
−0.1
3.6 V
25°C
0.05
−0.2
−2
Ω
0.1
0.2
0.05
2
µA
0V
Full
−10
25°C
Full
−0.1
3.6 V
25°C
10
0.05
−0.2
−2
0.1
0.2
0.05
2
µA
0V
Full
−10
−0.1
10
0.05
0.1
3.6 V
−0.2
Full
−0.1
0.2
0.05
Full
−0.2
0.2
Full
2
Full
0
V+
0.8
Full
−1
3.6 V
−1
0.05
µA
A
0.1
3.6 V
25°C
VI = 5.5 V or 0
V+
1
1
µA
A
V
V
µA
A
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
(2) All unused digital inputs of the device must be held at V+ or GND to ensure proper device operation. Refer to the TI application report, Implications
of Slow or Floating CMOS Inputs, literature number SCBA004.
3
W www.ti.com
SCDS189 – JANUARY 2005
Electrical Characteristics for 3.3-V Supply(1) (continued)
V+ = 3 V to 3.6 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
3.5
8
UNIT
Dynamic
Turn-on time
VCOM = 2 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
3.3 V
2.5
tON
Full
3 V to 3.6 V
2.5
Turn-off time
VCOM = 2 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
3.3 V
0.5
tOFF
Full
3 V to 3.6 V
0.5
VGEN = 0, RGEN = 0
CL = 0.1 nF,
See Figure 22
25°C
3.3 V
2
pC
9
2
ns
6.5
7
ns
Charge injection
QC
NC, NO
OFF capacitance
CNC(OFF)
CNO(ON)
VNC or VNO = V+ or GND,
Switch OFF,
See Figure 16
25°C
3.3 V
4.5
pF
COM
OFF capacitance
CCOM(OFF)
VCOM = V+ or GND,
Switch OFF,
See Figure 16
25°C
3.3 V
9
pF
NC, NO
ON capacitance
CNC(ON)
CNO(ON)
VNC or VNO = V+ or GND,
Switch ON,
See Figure 16
25°C
3.3 V
16
pF
COM
ON capacitance
CCOM(ON)
VCOM = V+ or GND,
Switch ON,
See Figure 16
25°C
3.3 V
16
pF
VI = V+ or GND,
See Figure 16
25°C
3.3 V
3
pF
BW
RL = 50 Ω,
Switch ON,
See Figure 18
25°C
3.3 V
300
MHz
OISO
RL = 50 Ω,
f = 10 MHz,
Switch OFF,
See Figure 19
25°C
3.3 V
−48
dB
Crosstalk
XTALK
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 20
25°C
3.3 V
−48
dB
Crosstalk
Adjacent
XTALK(ADJ)
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 21
25°C
3.3 V
−81
dB
THD
RL = 600 Ω,
CL = 50 pF,
f = 20 Hz to 20 kHz,
See Figure 23
25°C
3.3 V
0.21
%
Digital input
capacitance
Bandwidth
OFF isolation
Total harmonic
distortion
CI
Supply
25°C
Positive supply
I+
VI = V+ or GND,
Switch ON or OFF
3.6 V
current
Full
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
4
2.5
7
10
µA
A
W www.ti.com
SCDS189 – JANUARY 2005
Electrical Characteristics for 2.5-V Supply(1)
V+ = 2.3 V to 2.7 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal
range
ON-state
resistance
ON-state
resistance match
between
channels
ON-state
resistance
flatness
NC, NO
OFF leakage
current
VCOM,
VNC, VNO
ron
∆ron
ron(flat)
INC(OFF),
INO(OFF)
0
25°C
0 ≤ (VNC or VNO) ≤ V+,
ICOM = −24 mA,
Switch ON,
See Figure 13
VNC or VNO = 1.6 V,
ICOM = −24 mA,
Switch ON,
See Figure 13
0 ≤ (VNC or VNO) ≤ V+,
ICOM = −24 mA,
Switch ON,
See Figure 13
25°C
VNC or VNO = 0.5 V, VCOM = 2.2 V, Switch OFF,
or
See Figure 14
VNC or VNO = 2.2 V, VCOM = 0.5 V,
25°C
VNC or VNO = 0 to 3.6 V, VCOM = 3.6
V to 0,
Switch OFF,
or
See Figure 14
VNC or VNO = 3.6 V to 0, VCOM = 0
to 3.6 V,
Full
V+
12
2.3 V
20
22
25°C
0.3
Ω
2
Full
14
18
2.3 V
Full
20
−0.1
2.7 V
25°C
0.05
−0.2
−2
0.2
0.05
2
−10
10
VCOM = 0 to 3.6 V, VNC = 3.6 V to 0, Switch OFF,
or
See Figure 14
VCOM = 3.6 V to 0, VNC = 0 to 3.6 V,
25°C
VNC or VNO = 0.5 V, VCOM = Open, Switch ON,
or
See Figure 15
VNC or VNO = 2.2 V, VCOM = Open,
25°C
VCOM = 0.5 V, VNC or VNO = Open, Switch ON,
or
See Figure 15
VCOM = 2.2 V, VNC or VNO = Open,
Digital Control Inputs (IN, EN)(2)
25°C
Full
−0.2
0.2
Input logic high
Full
1.7
V+
0.7
NC, NO
ON leakage
current
INC(ON)
INO(ON)
COM
ON leakage
current
ICOM(ON)
Input logic low
Input leakage
current
VIH
VIL
IIH, IIL
VI = 5.5 V or 0
µA
0V
Full
25°C
ICOM(OFF)
Ω
0.1
VCOM = 0.5 V, VNC or VNO = 2.2 V, Switch OFF,
or
See Figure 14
VCOM = 2.2 V, VNC or VNO = 0.5 V,
COM
OFF leakage
current
Ω
1
2.3 V
Full
V
Full
Full
−0.1
2.7 V
−0.2
−2
0V
0.05
0.2
0.05
−10
−0.1
0.1
2
10
0.05
0.1
2.7 V
Full
−0.2
−0.1
0.2
0.05
Full
0
−0.1
Full
2.7 V
−1
0.05
µA
A
0.1
2.7 V
25°C
µA
A
0.1
1
µA
A
V
V
µA
A
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
(2) All unused digital inputs of the device must be held at V+ or GND to ensure proper device operation. Refer to the TI application report, Implications
of Slow or Floating CMOS Inputs, literature number SCBA004.
5
W www.ti.com
SCDS189 – JANUARY 2005
Electrical Characteristics for 2.5-V Supply(1) (continued)
V+ = 2.3 V to 2.7 V, TA = −40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SYMBOL
TA
V+
MIN
TYP
5
MAX
UNIT
Dynamic
Turn-on time
VCOM = 1.5 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
2.5 V
2.5
tON
Full
2.3 V to 2.7 V
2.5
9.5
Turn-off time
VCOM = 1.5 V,
RL = 300 Ω,
CL = 35 pF,
See Figure 17
25°C
2.5 V
0.5
tOFF
Full
2.3 V to 2.7 V
0.5
VGEN = 0, RGEN = 0
CL = 0.1 nF,
See Figure 22
25°C
2.5 V
1
pC
10.5
3
ns
7.5
9
ns
Charge injection
QC
NC, NO
OFF capacitance
CNC(OFF)
CNO(OFF)
VNC or VNO = V+ or GND,
Switch OFF,
See Figure 16
25°C
2.5 V
3
pF
COM
OFF capacitance
CCOM(OFF)
VCOM = V+ or GND,
Switch OFF,
See Figure 16
25°C
2.5 V
9
pF
NC, NO
ON capacitance
CNC(ON)
CNO(ON)
VNC or VNO = V+ or GND,
Switch ON,
See Figure 16
25°C
2.5 V
16
pF
COM
ON capacitance
CCOM(ON)
VCOM = V+ or GND,
Switch ON,
See Figure 16
25°C
2.5 V
16
pF
VI = V+ or GND,
See Figure 16
25°C
2.5 V
3
pF
BW
RL = 50 Ω,
Switch ON,
See Figure 18
25°C
2.5 V
300
MHz
OISO
RL = 50 Ω,
f = 10 MHz,
Switch OFF,
See Figure 19
25°C
2.5 V
−48
dB
Crosstalk
XTALK
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 20
25°C
2.5 V
−48
dB
Crosstalk
Adjacent
XTALK(ADJ)
RL = 50 Ω,
f = 10 MHz,
Switch ON,
See Figure 21
25°C
3.3 V
−81
dB
THD
RL = 600 Ω,
CL = 50 pF,
f = 20 Hz to 20 kHz,
See Figure 23
25°C
2.5 V
0.33
%
Digital input
capacitance
Bandwidth
OFF isolation
Total harmonic
distortion
CI
Supply
25°C
Positive supply
I+
VI = V+ or GND,
Switch ON or OFF
2.7 V
current
Full
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
6
2.5
7
10
µA
A
W www.ti.com
SCDS189 – JANUARY 2005
TYPICAL PERFORMANCE
10
18
TA = 25_C
16
8
14
ron (W)
12
ron (Ω)
855C
VCC = 2.5 V
10
8
255C
6
4
6
–405C
VCC = 3.3 V
4
2
2
0
0.0
0.5
1.0
1.5
2.0
2.5
VCOM (V)
3.0
0
0.0
3.5
Figure 1. ron vs VCOM
0.5
1.0
1.5
2.0
VCOM (V)
2.5
3.0
3.5
Figure 2. ron vs VCOM (V+ = 3.3 V)
18
40
16
14
Leakage Current (nA)
ron (W)
12
855C
10
8
255C
6
4
2
–405C
0
0.0
30
0.5
1.0
1.5
2.0
2.5
INC(ON)
ICOM(ON)
20
INC(OFF)
ICOM(OFF)
INO(ON)
10
INO(OFF)
0
−60
3.0
−40
−20
0
20
40
60
80
100
TA (°C)
VCOM (V)
Figure 4. Leakage Current vs Temperature
(V+ = 3.6 V)
Figure 3. ron vs VCOM (V+ = 3.3 V)
5
7
tON
6
5
V+ = 3.3 V
3
tON/tOFF (ns)
Charge Injection (pC)
4
2
V+ = 2.5 V
1
tOFF
4
3
2
1
0
0
1
2
3
4
VCOM (V)
Figure 5. Charge-Injection (QC) vs VCOM
0
2.0
2.5
3.0
3.5
4.0
V+ (V)
Figure 6. tON and tOFF vs Supply Voltage
7
W www.ti.com
SCDS189 – JANUARY 2005
TYPICAL PERFORMANCE
8
2.0
tON
7
1.8
5
Logic Level Threshold (V)
tON/tOFF (ns)
6
tOFF
4
3
2
1
0
−40
25
TA = 25_C
1.6
1.4
VIH
1.2
VIL
1.0
0.8
0.6
0.4
0.2
0.0
2.0 2.2
85
2.4 2.6
TA (5C)
2.8 3.0 3.2
V+ (V)
3.4 3.6
3.8 4.0
Figure 8. Logic-Level Threshold vs V+
Figure 7. tON and tOFF vs Temperature (V+ = 5 V)
0
0
−10
−1
−20
−30
−3
Gain (dB)
Gain (dB)
−2
−4
−5
−6
−40
−50
−60
−70
−80
−7
−90
1
10
100
1K
1
10
Frequency (MHz)
1k
Figure 10. OFF Isolation vs Frequency (V+ = 3.3 V)
0.45
4.0
0.40
3.5
0.35
3.0
0.30
2.5
0.25
2.0
I+ (µA)
THD (%)
Figure 9. Gain vs Frequency Bandwidth
(V+ = 3.3 V)
0.20
0.15
1.5
1.0
0.10
0.5
0.05
0.0
0.00
10
100
1000
Frequency (MHz)
10 K
100 K
Figure 11. Total Harmonic Distortion vs
Frequency
8
100
Frequency (MHz)
−40
25
85
TA (5C)
Figure 12. Power-Supply Current vs
Temperature (V+ = 3.3 V)
W www.ti.com
SCDS189 – JANUARY 2005
PIN DESCRIPTION
PIN
NUMBER
NAME
1
IN
DESCRIPTION
Digital control pin to select between NC and NO
2
NC1
Normally closed
3
NO1
Normally open
4
COM1
5
NC2
Normally closed
6
NO2
Normally open
7
COM2
8
GND
Common
Common
Digital ground
9
COM3
10
NO3
Common
Normally open
11
NC3
Normally closed
12
COM4
13
NO4
Normally open
14
NC4
Normally closed
15
EN
Chip Enable (active low)
16
V+
Power supply
Common
9
W www.ti.com
SCDS189 – JANUARY 2005
PARAMETER DESCRIPTION
SYMBOL
DESCRIPTION
VCOM
Voltage at COM
VNC
Voltage at NC
VNO
Voltage at NO
ron
Resistance between COM and NC or NO ports when the channel is ON
∆ron
Difference of ron between channels in a specific device
ron(flat)
Difference between the maximum and minimum value of ron in a channel over the specified range of conditions
INC(OFF)
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the OFF state
INC(ON)
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the ON state and the output (COM)
open
INO(OFF)
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state
INO(ON)
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output (COM)
open
ICOM(OFF)
Leakage current measured at the COM port, with the corresponding channel (COM to NC or NO) in the OFF state
ICOM(ON)
Leakage current measured at the COM port, with the corresponding channel (COM to NC or NO) in the ON state and the
output (NC or NO) open
VIH
Minimum input voltage for logic high for the control input (IN, EN)
VIL
Maximum input voltage for logic low for the control input (IN, EN)
VI
Voltage at the control input (IN, EN)
IIH, IIL
Leakage current measured at the control input (IN, EN)
tON
Turn-on time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay
between the digital control (IN) signal and analog output (NC or NO) signal when the switch is turning ON.
tOFF
Turn-off time for the switch. This parameter is measured under the specified range of conditions and by the propagation delay
between the digital control (IN) signal and analog output (NC or NO) signal when the switch is turning OFF.
QC
Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NC or NO) output.
This is measured in coulomb (C) and measured by the total charge induced due to switching of the control input.
Charge injection, QC = CL × ∆VCOM, CL is the load capacitance, and ∆VCOM is the change in analog output voltage.
CNC(OFF)
CNC(ON)
Capacitance at the NC port when the corresponding channel (NC to COM) is OFF
CNO(OFF)
CNO(ON)
Capacitance at the NC port when the corresponding channel (NO to COM) is OFF
CCOM(OFF)
CCOM(ON)
Capacitance at the COM port when the corresponding channel (COM to NC) is OFF
CI
Capacitance of control input (IN, EN)
OISO
OFF isolation of the switch is a measurement of OFF-state switch impedance. This is measured in dB in a specific frequency,
with the corresponding channel (NC to COM) in the OFF state.
XTALK
Crosstalk is a measurement of unwanted signal coupling from an ON channel to an OFF channel (NC1 to NO1). Adjacent
crosstalk is a measure of unwanted signal coupling from an ON channel to an adjacent ON channel (NC1 to NC2) .This is
measured in a specific frequency and in dB.
BW
Bandwidth of the switch. This is the frequency in which the gain of an ON channel is −3 dB below the DC gain.
THD
Total harmonic distortion describes the signal distortion caused by the analog switch. This is defined as the ratio of root mean
square (RMS) value of the second, third, and higher harmonic to the absolute magnitude of the fundamental harmonic.
I+
Static power-supply current with the control (IN) pin at V+ or GND
10
Capacitance at the NC port when the corresponding channel (NC to COM) is ON
Capacitance at the NC port when the corresponding channel (NO to COM) is ON
Capacitance at the COM port when the corresponding channel (COM to NC) is ON
W www.ti.com
SCDS189 – JANUARY 2005
PARAMETER MEASUREMENT INFORMATION
V+
VNC NC
COM
+
VCOM
Channel ON
VNO NO
r on +
IN or EN
VI
ICOM
VCOM * VNO or VNC
W
I COM
VI = VIH or VIL
+
GND
Figure 13. ON-State Resistance (ron)
V+
VNC NC
COM
+
VNO NO
VCOM
+
OFF-State Leakage Current
Channel OFF
VI = VIH or VIL
VNC or VNO = 0 to V+
and
VCOM =V+ to 0
IN or EN
VI
+
GND
Figure 14. OFF-State Leakage Current (ICOM(OFF), INC(OFF), INO(OFF)
V+
VNC NC
COM
+
VNO NO
VCOM
ON-State Leakage Current
Channel ON
VI = VIH or VIL
IN or EN
VI
+
GND
Figure 15. ON-State Leakage Current (ICOM(ON), INC(ON))
11
W www.ti.com
SCDS189 – JANUARY 2005
V+
Capacitance
Meter
VNC
NC
VNO
NO
VBIAS = V+ or GND
VI = VIH or VIL
VCOM COM
VBIAS
Capacitance is measured at NC,
NO, COM, and IN inputs during
ON and OFF conditions.
VI
IN or EN
GND
Figure 16. Capacitance (CI, CCOM(OFF), CCOM(ON), CNC(OFF), CNC(ON))
V+
NC or NO
VCOM(3)
VNCor VNO
TEST
RL
CL
tON
300 Ω
35 pF
tOFF
300 Ω
35 pF
COM
NC or NO
CL(2)
CL(2)
RL
RL
VI
Logic
Input(1)
V+
Logic
Input
(VI)
IN or EN
GND
50%
50%
0
tON
tOFF
Switch
Output
(VNC)
90%
90%
(1) All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
(2) CL includes probe and jig capacitance.
(3) See Electrical Characteristics for VCOM.
Figure 17. Turn-On (tON) and Turn-Off Time (tOFF)
V+
Network Analyzer
50 W
VNC
NC
Channel ON: NC to COM
COM
Source
Signal
VNO
VCOM
VI = V+ or GND
NO
Network Analyzer Setup
IN or EN
50 W
VI
+
Source Power = 0 dBm
(632-mV P-P at 50-W load)
GND
Figure 18. Bandwidth (BW)
12
DC Bias = 350 mV
W www.ti.com
SCDS189 – JANUARY 2005
V+
Network Analyzer
Channel OFF: NC to COM
50 W
VNC NC
VI = V+ or GND
COM
Source
Signal
50 W
VCOM
VNO NO
Network Analyzer Setup
IN or EN
Source Power = 0 dBm
(632-mV P-P at 50-W load)
VI
50 W
+
GND
DC Bias = 350 mV
Figure 19. OFF Isolation (OISO)
V+
Network Analyzer
50 W
Channel ON: NC to COM
VNC
NC
Channel OFF: NO to COM
VCOM
Source
Signal
VNO
VI
+
Network Analyzer Setup
50 W
IN or EN
50 W
VI = V+ or GND
NO
Source Power = 0 dBm
(632-mV P-P at 50-W load)
GND
DC Bias = 350 mV
Figure 20. Crosstalk (XTALK)
V+
Network Analyzer
50 W
VNC1
NC1
Source
Signal
VNC2 NC2
COM2
IN or EN
50 W
Channel ON: NC to COM
COM1
50 W
Network Analyzer Setup
Source Power = 0 dBm
(632 mV P-P at 50 W load)
VI
+
GND
DC Bias = 350 mV
Figure 21. Crosstalk Adjacent
13
W www.ti.com
SCDS189 – JANUARY 2005
V+
RGEN
VGEN
OFF
ON
OFF V
IL
NC or NO
COM
+
VIH
Logic
Input
(VI)
VCOM
∆VCOM
VCOM
NC or NO
CL(1)
VI
IN or EN
Logic
Input(2)
VGEN = 0 to V+
RGEN = 0
CL = 0.1 nF
QC = CL × ∆VCOM
VI = VIH or VIL
GND
(1) CL includes probe and jig capacitance.
(2) All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
Figure 22. Charge Injection (QC)
Channel ON: COM to NC
VSOURCE = V+ P-P
VI = VIH or VIL
fSOURCE = 20 Hz to 20 kHz
V+/2
V+
Audio Analyzer
RL
Source
Signal
COM
600 W
600 W
NO
IN or EN
VI
+
600 W
GND
(1) CL includes probe and jig capacitance.
Figure 23. Total Harmonic Distortion (THD)
14
10 mF
NC
10 mF
CL(1)
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated