SPAC1203F GLASS PASSIVATED SILICON RECTIFIER VOLTAGE 200 Volts CURRENT 12 Ampere FEATURES * Low leakage * Low forward voltage drop * High current capability * High surge capability * High reliability SlimPAQ MECHANICAL DATA * * * * Case: Slim PAQ Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any .138 (3.5) .098 (2.5) .245 (6.22) .220 (5.59) .280 (7.11) .260 (6.60) .037 (0.95) .043 (1.10) .010 (0.25) .006 (0.15) 1.25mm(Max.) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o .492 (12.5) .452 (11.5) C ambient temperature unless otherwise specified. .492 (12.5) .452 (11.5) resistive or inductive load. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL SPAC1203F UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 200 Volts Maximum RMS Voltage VRMS 140 Volts VDC 200 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T C = 125 o C IO 12 Amps Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) I FSM 125 Amps Typical Current Square Time I 2T 64.8 A 2S R q JC 4.1 R q JA 8.3 R q JL 1.6 Typical Thermal Resistance (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range CJ 40 T J, T STG -55 to + 175 0 C/ W pF 0 C ELECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) O CHARACTERISTICS Maximum Instantaneous Forward Voltage at 12 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 25 o C @T A = 100 o C SYMBOL SPAC1203F UNITS VF 1.1 Volts IR NOTES : 1. Thermal Resistance : Heat-sink case mounted or if PCB mounted. 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. "Fully ROHS compliant", "100% Sn plating (Pb-free)". 4. Suffix "R" for Reverse Polarity. 5. Available in Halogen-free epoxy by adding suffix -HF after the part nbr. 10 100 µAmps 2010-05 REV: B RATING AND CHARACTERISTICS CURVES ( SPAC1203F ) INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD CURRENT, (A) 25 20 D.C with heat sink 15 10 Single Phase Half Wave 60 Hz Inductive or Resistive Load 5 0 50 100 175 150 200 40 20 10 4 1.0 0.4 0.1 O 200 CT, JUNCTION CAPACITANCE, (pF) 1000 TA = 100 OC 100 10 TA = 25 C O 1.0 0.1 0 20 40 60 80 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 100 120 FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 60 40 20 10 6 4 2 0 140 T J = 25 OC 0.1 0.2 0.4 1.0 PERCENT RATED PEAK REVERSE VOLTAGE, (%) 2 8.3mS Single Half Sine-Wave JEDEC Method 125 100 75 50 25 2 10 20 40 100 FIG.4 TYPICAL JUNCTION CAPACITANCE 150 0 1 4 REVERSE VOLTAGE, (V) FIG.3 TYPICAL REVERSE CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (µA) CASE TEMPERATURE, ( C) T A = 25 OC Pulse Width = 300mS 1% Duty Cycle 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.