Preliminary SF2143A • • • • Designed for SDARS IF Receiver SAW Diplexer 72.54 / 80.46 MHz 11.4 X 5.3 mm Surface-Mount Case Complies with Directive 2002/95/EC (RoHS) 72.54/80.46 MHz SAW Diplexer Pb Absolute Maximum Ratings Rating Maximum Incident Power in Passband Maximum DC Voltage between any Two Terminals Operating Temperature Range Value Units +10 dBm 0 VDC -40 to +105 °C SM11453-10 Electrical Characteristics TDM1 Filter Characteristic Sym Nominal Center Frequency 1 dB Bandwidth 15 dB Bandwidth 30 dB Bandwidth Passband Minimum Insertion Loss including the Matching Network Amplitude Ripple, FC ± 1.85 MHz Attenuation Relative to ILMIN 50.00 to 66.48 MHz 66.48 to 68.08 MHz 77.30 to 78.60 MHz 78.60 to 86.50 MHz 86.50 to 91.50 MHz 91.50 to 100.0 MHz Group Delay Ripple Source Impedance (Differential) Load Impedance (Differential) FC BW1 BW15 BW30 ILMIN TDM2 Filter Characteristic Sym Nominal Center Frequency 1 dB Bandwidth 15 dB Bandwidth 30 dB Bandwidth Passband Minimum Insertion Loss including the Matching Network Amplitude Ripple, FC ± 1.85 MHz Attenuation Relative to ILMIN 50.00 to 74.39 MHz 74.39 to 75.99 MHz 85.21 to 86.50 MHz 86.50 to 91.50 MHz 91.50 to 100.0 MHz Group Delay Ripple Source Impedance (Differential) Load Impedance (Differential) FC BW1 BW15 BW30 ILMIN Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Notes 1 Min 3.7 40 37 37 40 45 45 Notes 1 Min 3.7 34 30 40 43 45 6 Typ 72.54 4.3 5.5 6.0 15.3 0.7 49 42 40 45 61 66 83 27 ohms or 200 ohms 1K ohms or 1.5K ohms Typ 80.46 4.3 5.5 6.4 15.7 1.5 41 35 42 44 56 120 27 ohms or 200 ohms 1K ohms or 1.5K ohms Max 6.7 7.7 18 Max 6.7 7.7 19.5 Units MHz MHz MHz MHz dB dBP-P dB dB dB dB dB dB nsP-P Units MHz MHz MHz MHz dB dBP-P dB dB dB dB dB nsP-P SM11453 11.4 x 5.3 mm Nominal Footprint RFM SF2143A YYWWS CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Tape and Reel Standard ANSI / EIA 481. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. ©Copyright 2009, RF Monolithics Inc. www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 1 of 5 SF2143A - 2/2/09 SF2143A TDM1 Filter Response SF2143A TDM2 Filter Response www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 2 of 5 SF2143A - 2/2/09 Matching Circuit: T D M 1 _ O U T P o rt 2 P o rt 1 D IP L E X E R T D M 2 _ O U T P o rt 3 www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 3 of 5 SF2143A - 2/2/09 SM11453-10 Case 10-Terminal Ceramic Surface-Mount Case 11.4 x 5.3 mm Nominal Footprint Electrical Connections Connection Terminals Port 1 Input 9, 10 Port 2 TDM1 5, 6 Port 3 TDM2 3, 4 Gound All Others PLATING 15-40uINS GOLD TO MIL-G-45204, TYPE 3, GRADE A, OVER 80-200uINS NICKEL TO FED SPEC. QQ-N-290. 5.30 4 1.12 1.20 5 6 7 2 5.08 11.40 2.54 0.79 3 1.88 8 1 10 9 2.54 ALL DIMENSIONS IN MM www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 4 of 5 SF2143A - 2/2/09 Tape and Reel Specifications Quantity Per Reel millimeters 7 178 500 13 330 2000 "B" REF. 100 REF. “B “ Inches See Detail "A" 13. 0 12.0 16.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 5.5 mm Bo 7.5 mm Ko 2.0 mm Pitch 8.0 mm W 16.0 mm PIN #1 USER DIRECTION OF FEED www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 5 of 5 SF2143A - 2/2/09