Preliminary SF2203E • Surface-mount 3.0 x 3.0 x 1.3 mm Package • Complies with Directive 2002/95/EC (RoHS) Pb 834 MHz SAW Filter Absolute Maximum Ratings Rating Value Units 15 dBm Input Power Level DC Voltage on any Non-ground Terminal 3 V Operating Temperature Range -30 to +85 °C Storage Temperature Range in Tape and Reel -40 to +95 °C 260 °C Solder Reflow Temperature, 10 seconds, 5 cycles maximum SM3030-6 Electrical Characteristics Characteristic Sym Notes Min FC Center Frequency Typ 834 ILMAX Maximum Insertion Loss, 819 to 849 MHz Amplitude Ripple, 819 to 849 MHz Return Loss, 819 to 849 MHz Max Units MHz 4 dB 2 dBP-P 10 dB Attenuation Referenced to 0 dB 10 to 660 MHz 30 660 to 710 MHz 25 710 to 760 MHz 20 864 to 869 MHz 15 894 to 934 MHz 20 934 to 990 MHz 25 990 to 2600 MHz dB 25 Source Impedance ZS 50 Load Impedance ZL 50 Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity Ω 933, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Input Terminals 5 Output 2 Ground All Others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 1 of 6 SF2203E - 7/16/10 Filter Passband Response 834 MHz filter 0 -2 -4 -6 Att.(dB) -8 S21 -10 spec. -12 -14 -16 -18 -20 784 794 804 814 824 834 844 Freq.(MHz) 854 864 874 884 Filter Test Circuit 5 0 o h m 5 SF2203E 2 5 0 o h m 1 , 3 , 4 , 6 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 2 of 6 SF2203E - 7/16/10 Filter Broadband Response, 0 to 2600 MHz 834 MHz filter 0 -10 Att.(dB) -20 -30 -40 -50 S21 spec . -60 -70 0 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. 260 520 780 1040 1300 1560 1820 2080 2340 2600 Freq.(MHz) Page 3 of 6 SF2203E - 7/16/10 Filter S11 Plot 834 MHz filter 0 -5 Att.(dB) -10 S11 -15 spec. -20 -25 -30 784 794 804 814 824 834 844 Freq.(MHz) 854 864 874 884 Filter S22 Plot 834 MHz filter 0 -5 Att.(dB) -10 S22 -15 spec. -20 -25 -30 784 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. 794 804 814 824 834 844 Freq.(MHz) 854 864 874 884 Page 4 of 6 SF2203E - 7/16/10 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 1 3 6 933 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 5 of 6 SF2203E - 7/16/10 Tape and Reel Specifications Quantity Per Reel millimeters 7 178 500 13 330 3000 "B" REF. 100 REF. “B” Inches See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions 2.0 3.35 mm Bo 3.35 mm Ko 1.40 mm Pitch 8.0 mm W 12.0 mm 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 Ao Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 6 of 6 SF2203E - 7/16/10