Preliminary XVT9003-1 • • • • Voltage Controlled Temperature Compensated Crystal Oscillator Excellent Frequency Stability & Low Phase Noise 3.2 x 2.5 x 1.2 mm Surface-mount Case Complies with Directive 2002/95/EC (RoHS) Pb 19.200000 MHz VCTCXO SM3225-4 Case Electrical Characteristics Characteristic Nominal Frequency Sym Notes Minimum fo Typical Maximum 19.200000 Units MHz Component Storage Temperature Range -55 +125 °C Storage Temperature Range in Tape and Reel -40 +85 °C 260 °C -40 +85 °C Soldering Profile, 10 seconds, up to 5 cycles Operating Temperature Range Power Supply Voltage Output Voltage with Load 10 pF||10 KΩ Vcc Vout 3.14 Control Voltage Control Voltage Input Impedance 3.46 V VP-P 0.8 Output Waveform Power Supply Current 3.30 clipped sinewave Icc 2.0 Vcon 1.5±1.0 V 100K Frequency Tolerance, Single Solder Reflow, Vcontrol = 1.50 V mA ohms ±2.0 ppm max @ 25 °C ±2 °C Frequency Stability versus: Temperature, -40 to 85 °C ±1.0 ppm Supply Voltage, 3.14 to 3.46 V ±0.2 ppm Load 10 pF||10 KΩ ±10% ±0.2 Control Voltage Frequency Range (1.5 ±1.0 V) ppm ±8 ppm/V Start Up Time, 90% of final RF level in VP-P Aging @ 25 °C 2.0 ±1 ms ppm/year Harmonics -5.0 dBc SSB Phase Noise @ 1 kHz Carrier Offset -130 dBc/Hz Stanard Shipping Quantity on 180 mm (7”) Reel Lid Symbolization 1000 units 9003-1/YWWS CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. The design, manufacturing process, and specifications of this device are subject to change without notice. www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 1 of 3 XVT9003-1 3/15/10 SM3225-4 Case 4-Terminal Surface-Mount Seam Weld Case 3.2 x 2.5 mm Nominal Footprint Pin Connection 1 Vcontrol 2 GND/CASE GND 3 Output 4 Vcc Application Circuit V C o n tro l V o lta g e In p u t 1 2 V C o T e m C o m www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. o lta g e n tr o lle p e ra tu p e n s a C ry s ta l O s c illa to C C 4 d 1 0 n F re te d r 3 O u tp u t Page 2 of 3 XVT9003-1 3/15/10 Reel Dimensions mm A B C D E F G H T1 T2 T3 Dimension 180 60 13.0 2.0 9.1 2.9 4.9 3.9 9.0 11.4 1.2 Tolerance ±1.0 +1.0/-0.0 ±0.2 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.3 ±1.0 ±0.1 Tape Dimensions mm A0 B0 W F E P0 P1 P2 D1 D K0 t Dimension 2.80 3.71 8.00 3.50 1.75 4.00 4.00 2.00 1.50 1.00 1.75 0.25 Tolerance ±0.10 ±0.10 +0.30/-0.10 ±0.05 ±0.10 ±0.10 ±0.10 ±0.05 +0.10/-0.00 +0.25/-0.00 ±0.10 ±0.02 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 3 of 3 XVT9003-1 3/15/10