SLPOWER GPMP900

GPMP900 SERIES
SINGLE OUTPUT MEDICAL POWER SUPPLY
SUMMARY
High Power Supplies 900 Watt AC/DC Universal Input Power Supply
g
• 90 -264 Vac nominal input range
• Overvoltage, over temp. and short circuit protection
• Approved to UL, CSA and EN Standards
• Power Good LED
• Low Leakage
• 12 V Auxiliary output
• Medical and commercial approvals
The GPMP Series are universal input AC/DC power supplies with power
factor correction (PFC) with up to 900 Watts ouput power. The GPMP
product incorporates true inhibit, power fail alarm, power good signal and
fan control. The series is approved to EN60601-1 and EN60950-1 to reduce
design-in time and end system compliance costs
SPECIFICATIONS
All specifications are typical at nominal input, full load at 25 OC unless otherwise stated
OUPUT SPECIFICATIONS
Output Power
Integral forced air
Total Regulation
INPUT SPECIFICATIONS
900 Watts max.
See table
Input Voltage range
Universal input
100-240 nom (90 - 264 max)
Vac
Rise time
At turn-on
3.0 s max.
Input frequency
47 Hz to 63 Hz
Transient response
Main output 25%
0.2 A/ms
3.5% max. dev. 350 ms recovery
to 1%
Input surge current
40 A max.
Ground Leakage current
264 Vac 60 Hz
160 mA
Temperature Coefficient
+/-0.03%/oC
Input current
115 Vac
12.0 A max
Overvoltage protection
125% +/-10%
Input current
230 Vac
6.0 A max
Input fuse
F1
15.0 A
Short Circuit protection
block wall
Yes
EMC INFORMATION
ENVIRONMENTAL SPECIFICATIONS
Conducted emissions
EN55011
Level B
Radiated emissions
EN55011
Level A
Line freq. harmonics
EN61000-3-2
Class A
Voltage fluctuations
EN61000-3-3
Complies (clause 5b)
ESD Air
EN61000-4-2
8 kV contact
ESD Contact
EN61000-4-2
6 kV air
Radiated immunity
EN61000-4-3
operating ambient
(see ratings chart)
-20 oC to +70 oC
non-operating
-40 to +85 oC
0 - 50 oC
Fan cooled
900 Watts
Maximum Altitude
operating / non-operating
10,000 ft. / 40,000
ft. max.
3 V/m
Relative Humidity
non-condensing
5% - 90% RH
Vibration (operating)
0.003 g /Hz
1.5 grms 3 axes 10
min/axis
Vibration (non-operating)
0.026 g2/Hz
5.0 grms 3 axes, 1
hr/axis
Shock
half-sine 20 gpk
10 ms, 3 axes, 6
shocks total
Shock
half-sine 40 gpk
10 ms, 3 axes, 6
shocks total
Fast Transients (EFT)
EN61000-4-4
2 kV 5 kHz
Line surge immunity
EN61000-4-5
1 kV diff /2 kV cm
Conducted immunity
EN61000-4-6
3 Vrms
Power freq. mag. field
EN61000-4-8
3 A/m
Voltage dip immunity
EN61000-4-11
Unit will ride through without loss of
output at 75% of rated load with AC
power fail warning.
Page 1 of 3
Thermal Performance
2
GENERAL SPECIFICATIONS
Hold-up time
Efficiency
isolation voltage
Switching frequency
Safety Approvals
Maximum weight
MODEL NUMBER
GPMP900-24
GPMP900-28
GPMP900-36
GPMP900-48
All Models Aux. output
120 Vac, 60 Hz
120 Vac 900 W output
input to ouput
input to ground
fixed
Output
24 V 37.5 A
28 V 32.1 A
36 V 25.0 A
48 V 18.8 A
12.25 V 0.25 A
>35 ms at 900 Watts output
>84 % 4000 Vac
1800 Vac
70 KHz, +/- 10 KHz
UL/EN/IEC 60601-1 CSA22.2 No.60601-1
2 kg (4.4 lbs)
Peak Output
24 V 39.5 A
28 V 34.1 A
36 V 27.0 A
48 V 20.8 A
N/A
Features
+/-5% adjust
+/-5% adjust
+/-5% adjust
+/-5% adjust
N/A
Ripple (3)
<240 mV
<240 mV
<240 mV
<240 mV
<120 mV
Regulation
+/- 0.5%
+/- 0.5%
+/- 0.5%
+/- 0.5%
11.9 - 12.7 V
NOTES
1. Integral forced air cooling
2. Peak rating is for 1 minute maximum 10% duty cycle
3. Noise measurent 20 MHz Bandwidth, differential mode. Measured with scope probe directly across output terminals of the power supply.
4. 12 V Auxiliary output does not shutdown with inhibit
MECHANICAL NOTES
The GPMP series is factory configured with standard connectors. Options B and T are available, Please contact factory for other connector arrangements
Page 2 of 3
OUTLINE AND MOUNTING DRAWING
Other drawings and SolidWorks™ 3D Models are available on request.
MOUNTING SCREW MAX DEPTH .200 FROM OUTSIDE OF CHASSIS
Condor DC Power Supplies Inc. 2311 Statham Parkway, Oxnard CA, 93033, USA. Phone:(805) 486 4565 Fax:(805) 487 8911 Email: [email protected]
GPMP900 Rev A 10/17/05.
Data Sheet © 2005 Condor DC Power Supplies Inc. The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Condor accepts
no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.
SolidWorks is a trademark of SolidWorks Corp.
Page 3 of 3