WM8740 w 24-bit, High Performance 192kHz Stereo DAC DESCRIPTION FEATURES The WM8740 is a very high performance stereo DAC designed for audio applications such as CD, DVD, home theatre systems, set top boxes and digital TV. The WM8740 supports data input word lengths from 16 to 24-bits and sampling rates up to 192kHz. The WM8740 consists of a serial interface port, digital interpolation filter, multi-bit sigma delta modulator and stereo DAC in a small 28-pin SSOP package. The WM8740 also includes a digitally controllable mute and attenuator function on each channel. • The internal digital filter has two selectable roll-off characteristics. A sharp or slow roll-off can be selected dependent on application requirements. Additionally, the internal digital filter can be by-passed and the WM8740 used with an external digital filter. The WM8740 supports two connection schemes for audio DAC control. The SPI-compatible serial control port provides access to a wide range of features including onchip mute, attenuation and phase reversal. A hardware controllable interface is also available. • • • • • • • • 120dB SNR (‘A’ weighted mono @48kHz), THD+N: -104dB @ FS 117dB SNR (‘A’ weighted stereo @48kHz), THD+N: -104dB @ FS Sampling frequency: 8kHz to 192kHz Selectable digital filter roll-off Optional interface to industry standard external filters Differential mono mode needing no glue logic Input data word: 16 to 24-bit Hardware or SPI compatible serial port control modes: Hardware mode: mute, de-emphasis, audio format control Serial mode: mute, de-emphasis, attenuation (256 steps), phase reversal Fully differential voltage outputs APPLICATIONS • • • CD, DVD audio Home theatre systems Professional audio systems BLOCK DIAGRAM WOLFSON MICROELECTRONICS plc To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews Production Data, April 2010, Rev 4.4 Copyright ©2010 Wolfson Microelectronics plc WM8740 Production Data TABLE OF CONTENTS DESCRIPTION ....................................................................................................... 1 FEATURES............................................................................................................. 1 APPLICATIONS ..................................................................................................... 1 BLOCK DIAGRAM ................................................................................................. 1 TABLE OF CONTENTS ......................................................................................... 2 PIN CONFIGURATION ........................................................................................... 3 ORDERING INFORMATION .................................................................................. 3 PIN DESCRIPTION ................................................................................................ 4 ABSOLUTE MAXIMUM RATINGS ......................................................................... 5 RECOMMENDED OPERATING CONDITIONS ..................................................... 6 ELECTRICAL CHARACTERISTICS ...................................................................... 6 INTERNAL POWER ON RESET CIRCUIT ............................................................ 9 DEVICE DESCRIPTION ....................................................................................... 12 SYSTEM CLOCK ........................................................................................................ 12 AUDIO DATA INTERFACE ......................................................................................... 12 NORMAL SAMPLE RATE ........................................................................................... 13 8 X FS INPUT SAMPLE RATE .................................................................................... 14 MODES OF OPERATION ........................................................................................... 14 HARDWARE CONTROL MODES ............................................................................... 14 SOFTWARE CONTROL INTERFACE......................................................................... 15 REGISTER MAP ......................................................................................................... 16 MUTE MODES ............................................................................................................ 20 FILTER RESPONSES ................................................................................................. 21 APPLICATIONS INFORMATION ......................................................................... 24 RECOMMENDED EXTERNAL COMPONENTS .......................................................... 24 RECOMMENDED EXTERNAL COMPONENTS VALUES ........................................... 24 SUGGESTED DIFFERENTIAL OUTPUT FILTER CIRCUIT ........................................ 25 RECOMMENDED DUAL DIFFERENTIAL HARDWARE SETUP ................................. 25 PACKAGE DIMENSIONS .................................................................................... 26 ADDRESS: .................................................................................................................. 27 w PD, Rev 4.4, April 2010 2 WM8740 Production Data PIN CONFIGURATION LRCIN 1 28 ML/I2S DIN 2 27 MC/DM1 BCKIN 3 26 MD/DM0 MODE8X 4 25 MUTEB SCLK 5 24 MODE DIFFHW 6 23 CSBIWO DGND 7 22 RSTB DVDD 8 21 ZERO AVDDR 9 20 AVDDL AGNDR 10 19 AGNDL VMIDR 11 18 VMIDL VOUTLP VOUTRP 12 17 VOUTRN 13 16 VOUTLN 15 AVDD AGND 14 ORDERING INFORMATION DEVICE TEMPERATURE RANGE PACKAGE MOISTURE SENSITIVITY LEVEL PEAK SOLDERING TEMPERATURE WM8740SEDS/V -40° to +85°C 28-pin SSOP MSL2 260°C WM8740SEDS/RV -40° to +85°C 28-pin SSOP MSL2 260°C Note: Reel Quantity: 2,000 w PD, Rev 4.4, April 2010 3 WM8740 Production Data PIN DESCRIPTION PIN NAME TYPE 1 LRCIN Digital input Sample rate clock input. 2 DIN Digital input Audio data serial input (except in 8XMODE when it is DINL). 3 BCKIN Digital input Audio data bit clock input . 4 MODE8X Digital input Internal pull-down, active high, 8 x fs mode. 5 SCLK Digital input System clock input. 6 DIFFHW Digital input Internal pull-down, active high, differential mono mode. 7 DGND Supply Digital ground supply. 8 DVDD Supply Digital positive supply. 9 AVDDR Supply Analogue positive supply. 10 AGNDR Supply Analogue ground supply. 11 VMIDR Analogue output Mid rail right channel. 12 VOUTRP Analogue output Right channel DAC output positive. 13 VOUTRN Analogue output Right channel DAC output negative. 14 AGND Supply Analogue ground supply. 15 AVDD Supply Analogue positive supply. 16 VOUTLN Analogue output Left channel DAC output negative. 17 VOUTLP Analogue output Left channel DAC output positive. 18 VMIDL Analogue output Mid rail left channel. 19 AGNDL Supply Analogue ground supply. 20 AVDDL Supply Analogue positive supply. 21 ZERO Digital output Infinite zero detect – active low. Open drain type output with active pull-down. 22 RSTB Digital input Reset input – active low. Internal pull-up. w DESCRIPTION PD, Rev 4.4, April 2010 4 WM8740 PIN NAME Production Data TYPE DESCRIPTION Hardware Mode Normal Mode Wordlength: Low for 16-bit data. High for 20-bit (normal) or 24-bit 2 I S data. Low for hardware mode. Differential Mode Wordlength: Low for 16-bit data. High for 20-bit (normal) or 24-bit 2 I S data. Low for left mono mode. High for right mono mode 23 CSBIWO Digital input Internal pull-down 24 MODE Digital input Internal pull-up 25 MUTEB Digital input Internal pull-up Low to soft mute. High for normal operation. 26 MD/DM0 Digital input Internal pull-up 27 MC/DM1 28 ML/I2S Software Mode Low for serial interface operation. 8X Mode Wordlength: Low for 20-bit data. High for 24-bit data. DINR High for software mode. Low to soft mute. High for normal operation. Low to soft mute. High for normal operation. Low to soft mute. High for normal operation. De-emphasis mode select bit 0. Low for no de-emphasis. High for 44.1kHz de-emphasis. LRP – LRCLK polarity select. Control serial interface data signal. Digital input Internal pull-up De-emphasis mode select bit 1. Low for normal filter operation. High for filter slow roll-off. Unused. Leave unconnected. Control serial interface clock signal. Digital input Internal pull-up Audio serial format: Low – right justified. High – I2S. Audio serial format: Low – right justified. High – I2S. Input data format: Low – right justified. High – left justified. Control serial interface load signal. Note: Digital input pins have Schmitt trigger input buffers. ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30°C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag. CONDITION Supply voltage Input Operating temperature range, TA Storage temperature prior to soldering Storage temperature after soldering MIN MAX -0.3V +7.0V GND -0.3V VDD + 0.3V -40°C +85°C 30°C max / 85% RH max -65°C +150°C Note: It is strongly recommended that AVDD, AVDDL and AVDDR are tied together. AGND, AGNDL and AGND right must also be tied together. w PD, Rev 4.4, April 2010 5 WM8740 Production Data RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Digital supply range DVDD -10% 3.3 to 5 +10% V Analogue supply range AVDD -10% 3.3 to 5 +10% V +0.3 V Ground AGND, DGND 0 Difference DGND to AGND -0.3 0 V Analogue supply current AVDD = 5V 13 Digital supply current DVDD = 5V 19 mA Analogue supply current AVDD = 3.3V 12 mA Digital supply current DVDD = 3.3V 12 mA mA Note: DVDD must be equal to, or less than the AVDD supply (i.e. DVDD = AVDD = +5V; DVDD = AVDD = +3.3V; DVDD = +3.3V AVDD = +5V). ELECTRICAL CHARACTERISTICS Test Conditions o AVDD, DVDD = 5V, AGND, DGND = 0V, TA = +25 C, fs = 48kHz, SCKI = 256fs unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT 120 dB 110 117 dB DAC Circuit Specifications SNR (See Note 1) Mono fs @ 48kHz Stereo fs @ 48kHz THD (full-scale) (See Note 2) Stereo fs @ 96kHz 116 dB Mono 0dB -104 dB -104 dB 117 dB Stereo 0dB THD+N (Dynamic range) (See Note 2) -95 -60dB Filter Characteristics (Sharp Roll-off) Passband ±0.0012 dB Stopband -3dB 0.4535fs dB 0.491fs ±0.0012 Passband ripple Stopband attenuation f > 0.5465fs -82 Delay time dB dB 30/fs s Filter Characteristics (Slow Roll-off) Passband ±0.001dB 0.274fs Stopband -3dB 0.459fs f > 0.732fs -82 ±0.001 Passband ripple Stopband attenuation Delay time dB dB 9/fs s -3dB 195 kHz 20kHz -0.043 dB Internal Analogue Filter Bandwidth Passband edge response Digital Logic Levels Input LOW level VIL Input HIGH level VIH Output LOW level VOL IOL = 2mA Output HIGH level VOH IOH = 2mA w 0.8 2.0 V DGND + 0.3V V DVDD - 0.3V PD, Rev 4.4, April 2010 6 WM8740 Production Data Test Conditions AVDD, DVDD = 5V, AGND, DGND = 0V, TA = +25oC, fs = 48kHz, SCKI = 256fs unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Analogue Output Levels Output level differential Minimum resistance load Into 10kΩ, full scale 0dB, (5V supply) 2 VRMS Into 10kΩ, full scale 0dB, (3.3V supply) 1.32 VRMS To midrail or AC coupled (5V supply) 1 kΩ To midrail or AC coupled (3.3V supply) 600 Ω Maximum capacitance load 5V or 3.3V Output DC level 100 pF AVDD/2 V 10 kΩ Reference Levels Potential divider resistance AVDD to VMIDL/VMIDR and VMIDL/VMIDR to AGND Voltage at VMIDL/VMIDR Notes: 1. 2. AVDD/2 Ratio of output level with 1kHz full scale input, to the output level with all zeros into the digital input, measured ‘A’ weighted over a 20Hz to 20kHz bandwidth. All performance measurements done with 20kHz low pass filter. Failure to use such a filter will result in higher THD+N and lower SNR and Dynamic Range readings than are found in the Electrical Characteristics. The low pass filter removes out of band noise; although it is not audible it may affect dynamic specification values. LRCIN tBCH tBCL tLB BCKIN tBCY tBL DIN tDS tDH Figure 1 Audio Data Input Timing Test Conditions AVDD, DVDD = 5V, AGND, DGND = 0V, TA = +25oC, fs = 48kHz, SCKI = 256fs unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Audio Data Input Timing Information BCKIN pulse cycle time tBCY 100 ns BCKIN pulse width high tBCH 40 ns BCKIN pulse width low tBCL 40 ns BCKIN rising edge to LRCIN edge tBL 20 ns LRCIN rising edge to BCKIN rising edge tLB 20 ns DIN setup time tDS 20 ns DIN hold time tDH 20 ns w PD, Rev 4.4, April 2010 7 WM8740 Production Data tSCKIL SCKI tSCKIH tSCKY Figure 2 System Clock Timing Requirements Test Conditions AVDD, DVDD = 5V, AGND, DGND = 0V, TA = +25oC, fs = 48kHz, SCKI = 256fs unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT System Clock Timing Information System clock pulse width high tSCKIH 10 ns System clock pulse width low tSCKIL 10 ns System clock cycle time tSCKY 27 ns tMLL tMHH ML/I2S tMCY tMCH tMCL tMLD tMLS MC/DM1 tMDS tMDH MD/DM0 LSB Figure 3 Program Register Input Timing – SPI Compatible Serial Control Mode Test Conditions AVDD, DVDD = 5V, AGND, DGND = 0V, TA = +25oC, fs = 48kHz, SCKI = 256fs unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Program Register Input Information MC/DM1 pulse cycle time tMCY 80 ns MC/DM1 pulse width low tMCL 32 ns MD/DM0 pulse width high tMCH 32 ns MD/DM0 set-up time tMDS 10 ns MC/DM1 hold time tMDH 10 ns ML/I2S pulse width low tMLL 10 ns ML/I2S pulse width high tMHH 10 ns ML/I2S set-up time tMLS 10 ns ML/I2S delay from MC tMLD 10 ns w PD, Rev 4.4, April 2010 8 WM8740 Production Data INTERNAL POWER ON RESET CIRCUIT 10K Power On Reset Circuit 10K Figure 4 Internal Power On Reset Circuit Schematic The WM8740 includes an internal Power On Reset Circuit which is used reset the digital logic into a default state after power up. Figure 4 shows a schematic of the internal POR circuit. The POR circuit is powered from AVDD. The circuit monitors DVDD and VMIDL and asserts PORB low if DVDD or VMIDL are below the minimum threshold Vpor_off. On power up, the POR circuit requires AVDD to be present to operate. PORB is asserted low until AVDD and DVDD and VMIDL are established. When AVDD, DVDD, and VMIDL have been established, PORB is released high, all registers are in their default state and writes to the digital interface may take place. On power down, PORB is asserted low whenever DVDD or VMIDLL drop below the minimum threshold Vpor_off. If AVDD is removed at any time, the internal Power On Reset circuit is powered down and PORB will follow AVDD. In most applications the time required for the device to release PORB high will be determined by the charge time of the VMIDLL node. Figure 5 Typical Power Up Sequence where DVDD is Powered before AVDD w PD, Rev 4.4, April 2010 9 WM8740 Production Data Figure 6 Typical Power Up Sequence where AVDD is Powered before DVDD Figure 7 Typical Power Up Sequence where AVDD is Powered and VMIDLL has Charged before DVDD Typical POR Operation (typical values, not tested) w SYMBOL TYP Vpora 0.35 UNIT V Vpord 0.8 V Vporr 0.85 V Vpora_off 2.6 V Vpord_off 0.8 V PD, Rev 4.4, April 2010 10 WM8740 Production Data In a real application the designer is unlikely to have control of the relative power up sequence of AVDD and DVDD. Using the POR circuit to monitor VMIDLL ensures a reasonable delay between applying power to the device and Device Ready. Figure 5 and Figure 6 show typical power up scenarios in a real system. Both AVDD and DVDD must be established and VMIDL must have reached the threshold Vporr before the device is ready and can be written to. Any writes to the device before Device Ready will be ignored. Figure 5 shows DVDD powering up before AVDD. Figure 6 shows AVDD powering up before DVDD. In both cases, the time from applying power to Device Ready is dominated by the charge time of VMIDLL. In the case where AVDD is powered long before DVDD, thus allowing VMIDL to charge above Vporr, the PORB will not release until DVDD passes the Vpord threshold. This situation is shown in Figure 7. w PD, Rev 4.4, April 2010 11 WM8740 Production Data DEVICE DESCRIPTION The WM8740 is a high performance 128fs oversampling rate stereo DAC employing a novel 64 level sigma delta DAC design which provides optimised signal-to-noise performance and clock jitter tolerance. It is ideally suited to high quality audio applications such as CD, DVD-audio, home theatre receivers and professional mixing consoles. The WM8740 supports sample rates from 8ks/s to 192ks/s. The control functions of the WM8740 are either pin selected (hardware mode) or programmed via the serial interface (software mode). Control functions that are available include: data input word length and format selection (16-24 bits: I2S, left justified or right justified): de-emphasis sample rate selection (48kHz, 44.1kHz and 32kHz); differential output modes; a software or hardware mute and independently digitally controllable attenuation on both channels. The digital filtering may be bypassed entirely by selecting MODE8X. Data is then input directly to the DAC, bypassing the digital filters. Left and right channels are input separately, using the MODE pin as the right channel input. This mode allows the use of alternative digital filters, such as the Pacific Microsonics PMD100 HDCD filter. In addition to the normal stereo operating mode the WM8740 may also be used in dual differential mode with either the left or right channel (selectable) being output dual differentially. Two WM8740s can then be used in parallel to implement a stereo channel, each supporting a single channel differentially. Note that this mode uses 2 pairs of differential outputs for each channel – the benefit is SNR improved by 3dB. This mode is available in both software and hardware modes and may also be used in conjunction with MODE8X. SYSTEM CLOCK Sample rates from 8ks/s up to 96ks/s are available, and automatically selected, with a system clock of 256fs or 384fs. In addition a system clock of 128fs or 192fs may be used, with sample rates up to 192ks/s. With a 128fs or 192fs system clock 64x oversampling mode operation is automatically selected and the first stage of the digital filter is bypassed. WM8740 has an asynchronous monitor circuit, which in the event of removal of the master system clock, resets the digital filters and analogue circuits, muting the output. Re-application of the system clock re-starts the filters from an intitialised state. Control registers are not reset under this condition. The WM8740 is tolerant of asynchronous bit clock jitter. The internal signal processing resynchronises to the external LRCIN once the phase difference between bit clock and the system clock exceeds half an LRCIN period. During this re-synch period the interpolating filters will either miss or repeat an audio sample, minimising the audible effects of the operation. Table 1 shows the typical system clock frequency inputs for the WM8740. SAMPLING RATE (LRCIN) SYSTEM CLOCK FREQUENCY (MHZ) 128fs 192fs 256fs 384fs 512fs 768fs 32kHz 4.096 6.144 8.192 12.288 16.384 24.576 44.1kHz 5.6448 8.467 11.2896 16.9340 22.5792 33.8688 48kHz 6.114 9.216 12.288 18.432 24.576 36.864 96kHz 12.288 18.432 24.576 36.864 Unavailable Unavailable 192kHz 24.576 36.864 Unavailable Unavailable Unavailable Unavailable Table 1 System Clock Frequencies Versus Sampling Rate AUDIO DATA INTERFACE Data may be input at a rate corresponding to the system clock having a rate of 256fs or 384fs, in which case an oversampling ratio of 128x is selected. Alternatively a rate of 128fs or 192fs may be used, in which case the first filter stage is bypassed and an oversampling ratio of 64x results. Finally, in MODE8X, data may be input at 8x the normal rate, in which case separate input pins are used to input the two stereo channels of data (unless DIFFHW mode and MODE8X are both selected, in which case only a mono channel is converted differentially). In MODE8X all filter stages are bypassed, prior to the sigma delta modulator, MODE8X is not supported at 192kHz sampling rate. Data is input MSB first in all modes. w PD, Rev 4.4, April 2010 12 WM8740 Production Data NORMAL SAMPLE RATE In normal mode, the data is input serially on one pin for both left and right channels. Data can be “right justified” meaning that the last 16, 20 or 24 bits (depending on chosen PCM word length) that were clocked in prior to the transition on LRCIN are valid. Alternatively data can be “left justified” (20 and 24-bit PCM data only), where the bits are clocked in as the first 20 or 24 bits after a transition on LRCIN. For the three I2S modes supported (16-bit, 20-bit and 24-bit PCM data), data is clocked “left justified” except with one additional preceding clock cycle. 1/fs LEFT RIGHT LRCIN (PIN 1) BCKIN (PIN 3) 16-BIT RIGHT JUSTIFIED DIN (PIN 2) B2 B1 B0 20-BIT RIGHT JUSTIFIED DIN (PIN 2) B2 B1 24-BIT RIGHT JUSTIFIED DIN (PIN 2) B2 B1 B15 B2 B1 B0 B15 B2 B1 B0 B0 B19 B18 B17 B2 B1 B0 B19 B18 B17 B2 B1 B0 B0 B23 B22 B21 B20 B19 B2 B1 B0 B23 B22 B21 B20 B19 B2 B1 B0 24-BIT LEFT JUSTIFIED DIN (PIN 2) B0 B23 B22 B21 B4 B3 20-BIT LEFT JUSTIFIED DIN (PIN 2) B0 B19 B18 B17 B0 B2 B1 B0 B23 B22 B21 B4 B19 B18 B17 B0 LEFT B3 B2 B1 B0 RIGHT LRCIN (PIN 1) BCKIN (PIN 3) 16-BIT I2S DIN (PIN 2) B15 B2 B1 B0 24-BIT I2S DIN (PIN 2) B23 B6 B5 B4 B3 20-BIT I2S DIN (PIN 2) B19 B2 B1 B0 B2 B1 B0 B15 B2 B1 B0 B23 B6 B5 B4 B19 B2 B1 B0 B15 B3 B2 B1 B0 B23 B19 Figure 8 Audio Data Input Format w PD, Rev 4.4, April 2010 13 WM8740 Production Data 8 X FS INPUT SAMPLE RATE Due to the higher speed of the interface in 8 x fs mode, audio data is input on two pins. The MODE pin (pin 24) is used as the second input for the right channel data and left data is input on DIN (pin2). In this mode, software control of the device is not available. The data can be input in two formats, left or right justified, selectable by ML/I2S and two word lengths (20 or 24 bit), selectable by CSBIWO. In both modes the data is always clocked in MSB first. For left justified data the word start is marked by the falling edge of LRCIN. The data is clocked in on the next 20/24 BCKIN rising edges. This format is compatible with devices such as the PMD100. For right justified the data is justified to the rising edge of LRCIN and the data is clocked in on the preceding 20/24 BCKIN rising edges before the LRCIN rising edge. This format is compatible with devices such as the DF1704 or SM5842. In both modes the polarity of LRCIN can be switched using MD/DM0. Differential hardware mode can be used in conjunction with 8fs mode by setting the DIFFHW pin high. In differential 8fs mode the data is input on DIN and output differentially. MODE is unused and must be tied low. 1/8fs LRCIN (PIN 1) BCKIN (PIN 3) LEFT AUDIO DATA DIN (PIN 2) B23 B22 B21 B20 B19 B2 B1 B0 B23 B22 B21 B20 RIGHT AUDIO DATA MODE (PIN 24) B23 B22 B21 B20 B19 B2 B1 B0 B23 B22 B21 B20 1/8fs LRCIN (PIN 1) BCKIN (PIN 3) LEFT AUDIO DATA DIN (PIN 2) B23 B22 B21 B20 B19 B2 B1 B0 RIGHT AUDIO DATA MODE (PIN 24) B23 B22 B21 B20 B19 B2 B1 B0 Figure 9 Audio Data Input Format (8 x fs Operation) MODES OF OPERATION Control of the various modes of operation is either by software control over the serial interface, or by hard-wired pin control. Selection of software or hardware mode is via MODE pin. The following functions may be controlled either via the serial control interface or by hard wiring of the appropriate pins. HARDWARE CONTROL MODES When the MODE pin is held ‘low’ the following hardware modes of operation are available. In Hardware differential mode or 8X mode some of these modes/control words are altered or unavailable. w PD, Rev 4.4, April 2010 14 WM8740 Production Data DE-EMPHASIS CONTROL MDDM1 PIN 27 MCDMO PIN 26 DE-EMPHASIS L L Off L H 48kHz H L 44.1kHz H H 32kHz Table 2 De-Emphasis Control AUDIO INPUT FORMAT ML/I2S PIN 28 CSBIWO PIN 23 DATA FORMAT L L 16 bit normal right justified L H 20 bit normal right justified H L 16 bit I2S H H 24 bit I2S Table 3 Audio Input Format SOFT MUTE MUTEB PIN 25 FUNCTION L Mute On (no output) H Mute Off (normal operation) Table 4 Soft Mute A logic low on the MUTEB pin will cause the attenuation to ramp to infinite attenuation at a rate of 128/fs seconds per 0.5dB step. Setting MUTEB high will cause the attenuation to ramp back to its previous value. SOFTWARE CONTROL INTERFACE The WM8740 can be controlled using a 3-wire serial interface. MD/DM0 (pin 26) is used for the program data, MC/DM1 (pin 22) is used to clock in the program data and ML/I2S (pin 28) is use to latch in the program data. The 3-wire interface protocol is shown in Figure 6. CSB/IWO (pin 23) must be low when writing. ML/I2S (PIN 28) MC/DM1 (PIN 27) MD/DM0 (PIN 26) B15 B14 B13 B2 B1 B0 Figure 10 Three-Wire Serial Interface w PD, Rev 4.4, April 2010 15 WM8740 Production Data REGISTER MAP WM8740 controls the special functions using 4 program registers, which are 16-bits long. These registers are all loaded through input pin MD/DM0. After the 16 data bits are clocked in, ML/I2S is used to latch in the data to the appropriate register. Table 5 shows the complete mapping of the 4 registers. Note that in hardware differential mode and 8X modes, software control is not available. The hardware differential mode (Diff[1:0]) clock loss detector disable (CDD) can only be accessed by writing to M2[8:5] with the pattern 1111. Register M4 is then accessible by setting A[2:0] to 110. B15 B14 B13 B12 M0 - - - - M1 - - - M2 - - M3 - - M4 - - B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 A2 (0) A1(0) A0(0) LDL AL7 AL6 AL5 AL4 AL3 AL2 AL1 AL0 - A2(0) A1(0) A0(1) LDR AR7 AR6 AR5 AR4 AR3 AR2 AR1 AR0 - - A2(0) A1(1) A0(0) - - - - IW1 IW0 OPE DEM MUT - - A2(0) A1(1) A0(1) IZD SF1 SF0 - REV SR0 ATC LRP IS - - A2(1) A1(1) A0(0) - - - - - - CDD DIFF1 DIFF0 2 Table 5 Mapping of Program Registers REGISTER BITS NAME DEFAULT 0 [7:0] AL[7:0] FF 8 LDL 0 1 [7:0] AR[7:0] FF 8 LDR 0 Attenuation data load control for right channel. 2 0 MUT 0 Left and right DACs soft mute control. 1 DEM 0 De-emphasis control. 2 OPE 0 Left and right DACs operation control. [4:3] IW[1:0] 0 Input audio data bit select. 3 4 DESCRIPTION Attenuation data for left channel. Attenuation data load control for left channel. Attenuation data for right channel. 0 I2S 0 Audio data format select. 1 LRP 0 Polarity of LRCIN select. 2 ATC 0 Attenuator control. 3 SR0 0 Digital filter slow roll-off select. 4 REV 0 Output phase reverse. [7:6] SF[1:0] 0 Sampling rate select. 8 IZD 0 Infinite zero detection circuit control. [5:4] DIFF 0 Differential output mode. 6 CDD 0 Clock loss detector disable. Table 6 Register Bit Descriptions DAC OUTPUT ATTENUATION The level of attenuation for eight bit code X, is given by: 0.5 ∗ (X - 255) dB, 1 ≤ X ≤ 255 - ∞dB (mute), X=0 Bit 8 in register 0 (LDL) is used to control the loading of attenuation data in B[7:0]. When LDL is set to 0, attenuation data will be loaded into AL[7:0], but it will not affect the filter attenuation. LDR in register 1 has the same function for right channel attenuation. Only when LDL or LDR is set to '1' will the filter attenuation be updated. This permits left and right channel attenuation to be updated simultaneously. Attenuation level is controlled by AL[7:0] (left channel) or AR[7:0] (right channel). Attenuation levels are given in Table 7. w PD, Rev 4.4, April 2010 16 WM8740 Production Data X[7:0] ATTENUATION LEVEL 00(hex) - ∞dB (mute) 01(hex) -127.0dB : : : : FD(hex) -1.0dB FE(hex) -0.5dB FF(hex) 0.0dB Table 7 Attenuation Control Level Bit 2 in Reg3 is used to control the attenuator (ATC). When ATC is “high”, the attenuation data loaded in program register 0 is used for both the left and the right channels. When ATC is low, the attenuation data for each register is applied separately to left and right channels. SOFT MUTE MUT (REG2, B0) L Soft Mute off (normal operation) H Soft Mute on (no output) Table 8 Soft Mute Setting MUT causes the attenuation to ramp from the current value down to 00. The values held in the attenuation registers are unchanged. When MUT is reset the attenuation will ramp back up to the previous value. The ramp rate is 128/fs s/0.5dB step. DIGITAL DE-EMPHASIS DEM (REG2, B1) L De-emphasis off H De-emphasis on Table 9 Digital De-Emphasis DAC OPERATION ENABLE OPE (REG2,B2) L Normal operation H DAC output forced to bipolar zero, irrespective of input data. Table 10 DAC Operation Enable AUDIO DATA INPUT FORMAT I2S (REG3, B0) IW1 (REG2, B4) IW0 (REG2, B3) AUDIO INTERFACE 0 0 0 16-bit standard right justified 0 0 1 20-bit standard right justified 0 1 0 24-bit standard right justified 0 1 1 24-bit left justified (MSB first) 1 0 0 16-bit I2S 1 0 1 24-bit I2S 1 1 0 20-bit I2S 1 1 1 20-bit left justified (MSB first) Table 11 Audio Data Input Format w PD, Rev 4.4, April 2010 17 WM8740 Production Data POLARITY OF LR INPUT CLOCK The left channel data for a particular sample instant is always input first, then the right channel data. LRP (REG3, B1) L LR High – left channel LR Low – right channel H LR Low – left channel LR High – right channel Table 12 Polarity of LR Input Clock INDIVIDUAL OR COMMON ATTENUTATION CONTROL ATC (REG3, B2) L Individual control H Common control from Reg0 Table 13 Individual or Common Attenuation Control DIGITAL FILTER ROLL-OFF SELECTION SRO (REG3, B3) L Sharp H Slow Table 14 Digital Filter Roll-Off Selection ANALOGUE OUTPUT POLARITY REVERSAL REV (REG3, B4) L Normal H Inverted Table 15 Analogue Output Polarity Reversal DE-EMPHASIS SAMPLE RATE SF1 (REG3, B7) SF0 (REG3, B6) SAMPLE RATE 0 0 No de-emphasis 0 1 48kHz 1 0 44.1kHz 1 1 32kHz Table 16 De-Emphasis Sample Rate INFINITE ZERO DETECT IZD (REG3, B8) L Zero detect mute off H Zero detect mute on Table 17 Infinite Zero Detect w PD, Rev 4.4, April 2010 18 WM8740 Production Data SOFTWARE DIFFERENTIAL MONO MODE To control the WM8740 in software differential mode register M4 must be written to. A ‘key’ register write must be made to register M2 to allow access to register M4 which is ‘locked’ as default. Bits B5 to B8 of register M2 must be set to ‘1’ (0x01e0). With register M4 ‘unlocked’, bits B4 and B5 may be used to set the required differential output mode; normal stereo, reversed stereo, mono left or mono right, as shown in Table 18. DIFF[1:0] B[5:4]) DIFFERENTIAL OUTPUT MODE 00 Stereo 10 Stereo reverse. 01 Mono left – differential outputs. VOUTLP (17) is left channel. VOUTLN (16) is left channel inverted. VOUTRP (12) is left channel inverted. VOUTRN (13) is left channel. 11 Mono right – differential outputs. VOUTLP (17) is right channel inverted. VOUTLN (16) is right channel. VOUTRP (12) is right channel. VOUTRN (13) is right channel inverted. Table 18 Differential Output Modes Using these controls a pair of WM8740 devices may be used to build a dual differential stereo implementation with higher performance and differential output. Note: DIFFHW mode pin may be used to achieve the same result by hardware means. CLOCK LOSS DETECTOR DISABLE CDD (REG4, B6) L Clock loss detector on R Clock loss detector off Table 19 Clock Loss Detector Disable When the system clock is inactive for approximately 100μs, the clock loss detector circuit detects the loss of clock and the analogue circuitry is forced into a mute condition and the digital filters reset. Setting the CDD bit disables this behaviour. w PD, Rev 4.4, April 2010 19 WM8740 Production Data MUTE MODES The device has various mute modes. DIGITAL FILTER ANALOGUE ANRES ANMUTE Reg bit OPE = ‘1’ Unaffected Asserted MUTEB pin Gain ramped to zero On release volume ramps to previous value Asserted when gain = 0 AUTOMUTE (detect 1024 zero input samples) Automute has no effect on digital filters Asserted after 1024 zero input samples if IZD = 1 Reg bit MUT As MUTEB pin As MUTEB pin Gain = 00 (left and right) Gain = -∞dB Asserted RAM initialise Gain initialised to 0dB Loss of system clock Not running (no clock). On clock restart, filters initialised, RAM initialised. Registers unchanged Asserted Asserted No LRCLK or invalid SCLK/LRCLK ratio Filters initialised, RAM initialised. Registers unchanged Asserted Asserted RB Reset – gain initialised to 0dB Asserted Asserted Power-on reset Reset Asserted Asserted Asserted Table 20 Mute Modes • 1. 2. 3. ANRES is the reset to the switched capacitor filter. ANMUTE is an analogue muting signal gating the analogue signal at the output (after the SC filter) AUTOMUTE is asserted when both the IZD register bit is asserted and the input audio data has been zero on both left and right channels for 1024 input samples. The first non-zero sample de-asserts. Applying a logic low to MUTEB or setting MUT in Reg2 causes the gain registers to ramp to zero. When a logic high is applied, the gain ramps slowly back up to the value held in the appropriate attenuation register (AL or AR). The ramp rate = 128/fs s/0.5dB step. If SOFTMUTE is set or MUTEB=0 then GAINL and GAINR are overridden to 00 GAINL[0:7] SOFTMUTE Signal Processing GAINR[0:7] MUTEB gain ramps between previous and new gain setting Automute: Detect 1024 zero input samples IZD OPE FREQ_INVALID INIT ANMUTE ZERO Figure 11 Mute Modes w PD, Rev 4.4, April 2010 20 WM8740 Production Data FILTER RESPONSES Figure 12 Digital Filter Response (Sharp Roll-off Mode) Figure 13 Digital Filter Response (Sharp Roll-off Mode) Figure 14 Digital Filter Response (Slow Roll-off Mode) Figure 15 Digital Filter Response (Slow Roll-off Mode) 0 Response (dB) -20 -40 -60 -80 -100 -120 0 0.2 0.4 0.6 0.8 1 1.2 Frequency (Fs) 1.4 1.6 1.8 2 Figure 16 Digital Filter Response 128fs Mode (192kHz Sample Rate) Normal Mode – Solid, Slow Mode – Dashed w PD, Rev 4.4, April 2010 21 Production Data 1 1 0.8 0.8 Impulse Response Impulse Response WM8740 0.6 0.4 0.2 0 0.6 0.4 0.2 0 -0.2 -0.2 -0.4 -0.4 0 10 20 30 40 Time (input samples) 50 0 60 Figure 17 Impulse Response (Normal Roll-off, 0.0 -1.0 -2.0 -2.0 -3.0 -3.0 Response (dB) Response (dB) 0.0 -4.0 -5.0 -6.0 50 60 -4.0 -5.0 -6.0 -7.0 -7.0 -8.0 -8.0 -9.0 -9.0 -10.0 -10.0 4000 30 40 Time (input samples) no De-emphasis) -1.0 2000 20 Figure 18 Impulse Response (Slow Roll-off, no De-emphasis) 0 10 6000 8000 10000 12000 14000 16000 0 5000 10000 Frequency (Fs) 15000 20000 Frequency (Fs) Figure 19 De-emphasis Frequency Response (fs=32kHz) Figure 20 De-emphasis Frequency Response (fs=44.1kHz) 0.0 0.4 -1.0 0.3 -2.0 0.2 Response (dB) Response (dB) -3.0 -4.0 -5.0 -6.0 0.1 0.0 -0.1 -7.0 -0.2 -8.0 -0.3 -9.0 -10.0 -0.4 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 20000 0 Frequency (Fs) Figure 21 De-emphasis Frequency Response (fs=48kHz) 2000 4000 6000 8000 10000 12000 14000 16000 Frequency (Fs) Figure 22 De-emphasis Frequency Response Error (fs=32kHz) w PD, Rev 4.4, April 2010 22 Production Data 0.4 0.4 0.3 0.3 0.2 0.2 0.1 0.1 Response (dB) Response (dB) WM8740 0.0 -0.1 0.0 -0.1 -0.2 -0.2 -0.3 -0.3 -0.4 -0.4 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 Frequency (Fs) Figure 23 De-emphasis Frequency Response Error (fs=44.1kHz) w 20000 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 20000 Frequency (Fs) Figure 24 De-emphasis Frequency Response Error (fs=48kHz) PD, Rev 4.4, April 2010 23 WM8740 Production Data APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS DVDD C1 + 8 DVDD AVDD 9 AVDDR C2 7 DGND AVDDL DGND AGND AGNDR AGNDL 28 27 Software I/F or Hardware Control 26 23 22 4 6 ML/I2S VOUTLN MC/DM1 MD/DM0 CSB/IWO VOUTLP VOUTRN VOUTRP AVDD 15 20 + 14 C3 C4 C5 C6 10 AGND 19 16 - 17 LEFT OUTPUT DATA + 13 - 12 RIGHT OUTPUT DATA + RSTB MODE8X WM8740 AVDD DIFFHW R1 24 25 MODE MUTEB ZERO VMIDR VMIDL 1 2 Audio Serial Data I/F 3 21 11 18 LRCIN + C9 System Clock Input Notes: 1. C1 2 0 DIN BCKIN R2 5 C1 + C 11 AGND SCLK R2 AGND and DGND should be connected as close to the WM8740 as possible. to C , and C 1 should be positioned as close to the WM8740 as possible. C9 1 2. C2 3. Capacitor type used can have a big effect on device performance. It is recommended that capacitors with very low ESR are used and that ceramics are either NPO or COG type material to achieve best performance from the WM8740. 5 Figure 25 External Components Diagram RECOMMENDED EXTERNAL COMPONENTS VALUES COMPONENT REFERENCE SUGGESTED VALUE DESCRIPTION C1 and C6 10μF De-coupling for DVDD and AVDD. C2 to C5 0.1μF De-coupling for DVDD and AVDD. C7 and C8 10μF Output AC coupling caps to remove VMID DC level from outputs. C9 and C11 0.1μF Reference de-coupling capacitors for VMIDR and VMIDL. C10 and C12 10μF R1 10kΩ Resistor to AVDD for open drain output operation. R2 51Ω Source termination resistors. Table 21 External Components Description w PD, Rev 4.4, April 2010 24 WM8740 Production Data SUGGESTED DIFFERENTIAL OUTPUT FILTER CIRCUIT Figure 26 Suggested Differential Output Filter Circuit RECOMMENDED DUAL DIFFERENTIAL HARDWARE SETUP Figure 27 Recommended Dual Differential Hardware Setup w PD, Rev 4.4, April 2010 25 WM8740 Production Data PACKAGE DIMENSIONS DS: 28 PIN SSOP (10.2 x 5.3 x 1.75 mm) b DM007.E e 28 15 E1 1 D E GAUGE PLANE 14 c A A2 A1 Θ L 0.25 L1 -C0.10 C Symbols A A1 A2 b c D e E E1 L L1 θ MIN ----0.05 1.65 0.22 0.09 9.90 7.40 5.00 0.55 o 0 REF: Dimensions (mm) NOM --------1.75 0.30 ----10.20 0.65 BSC 7.80 5.30 0.75 1.25 REF o 4 SEATING PLANE MAX 2.0 0.25 1.85 0.38 0.25 10.50 8.20 5.60 0.95 o 8 JEDEC.95, MO-150 NOTES: A. ALL LINEAR DIMENSIONS ARE IN MILLIMETERS. B. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. C. BODY DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSION, NOT TO EXCEED 0.20MM. D. MEETS JEDEC.95 MO-150, VARIATION = AH. REFER TO THIS SPECIFICATION FOR FURTHER DETAILS. w PD, Rev 4.4, April 2010 26 WM8740 Production Data IMPORTANT NOTICE Wolfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current. Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty. Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. In order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product. Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. Any use of products by the customer for such purposes is at the customer’s own risk. Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. Any provision or publication of any third party’s products or services does not constitute Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document belong to the respective third party owner. Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. ADDRESS: Wolfson Microelectronics plc 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: [email protected] w PD, Rev 4.4, April 2010 27