DATA SHEET UF1000~UF1008 SEMICONDUCTOR ULTRAFAST SWITCHING RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes FEATURES ‧Plastic package has Underwriters Laboratory Flammability Classification 94V-O Utilizing Flame Retardant Epoxy Molding Compound TO-220AC Unit:inch(mm) ‧Exceeds environmental standards of MIL-S-19500/228 .196(5.0) .163(4.16) ‧Low power loss, high efficiency .419(10.66) MAX ‧Low forward voltage, high current capability ‧High surge capacity ‧Ultra Fast recovery times, high voltage .054(1.39) .045(1.15) DIA .139(3.55) .MIN .269(6.85) .226(5.75) ‧High temperature soldering : 260OC / 10 seconds at terminals .624(15.87) .548(13.93) ‧ Pb free product at available : 99% Sn above meet RoHS environment substance directive request PIN1 MECHANCALDATA 2 3 .177(4.5) .MAX .114(2.9) .098(2.5) ‧Case: TO-220AC molded plastic .50(12.7) MAX ‧Terminals: Lead solderable per MIL-STD-202, Method 208 .038(0.96) .019(.5) ‧Polarity: As marked ‧Mounting Position: Any ‧Weight: 0.08 ounce, 2.24 gram .100(2.54) .025(0.65) MAX MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 O C J ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20% SYMBOL TYPE NUMBER UF1000 UF1001 UF1002 UF1003 UF1004 UF1006 UF1008 UNITS Maximum Recurrent Peak Reverse Voltage 50 100 200 300 400 600 800 V Maximum RMS Voltage 35 70 140 210 280 420 560 V Maximum DC Blocking Voltage 50 100 200 300 400 600 800 V Maximum Average Forward Rectified Current .375”(9.5mm) lead length @ TC=100 °C Peak Forward Surge Current, 8.3ms single half sine wave superimposed on rated load(JECEC method) Maximum Instantaneous Forward Voltage at 10.0A Maximum DC Reverse Current @T A=25 °C at Rated DC Blocking Voltage @TA=125°C VF 10 A 150 A 1.0 1.3 1.7 IR V μA 10.0 μA 500 Maximum Reverse Recovery Time(Note 1) 50 75 ns Typical Junctioncap acitance (Note 2) 80 50 pF Typical Junction Resi stance (Note 2) RөJA Operating and Storage Temperature Range TJ ,TSTG TSTG 15 °C/W -55 to +150 °C NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1A, Irr=0.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 3. Thermal resistance from junction to ambient and from junction to lead length 0.375"(9.5mm) P.C.B. mounted http://www.yeashin.com 1 REV.02 20110725 RATING AND CHARACTERISTIC CURVES UF1000~UF1008 RATING AND CHARACTERISTIC CURVES UF1000 THRU UF1008 trr +0.5A 0 -0.25 -1.0 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. 1cm SET TIME BASE FOR 50 ns/cm Source Impedance = 50 Ohms 20 12 8 4 0 0 50 100 150 CASE TEMPERATURE, °C PEAK FORWARD CURRENT AMPERES Fig. 1-TYPICAL FORWARD CURRENT DERATING CURVE TJ = 125 °C 100 10 TJ = 25 °C 1.0 150 0.1 TJ = 125 °C 8.3ms SINGLE HALF SINCEWAVE JEDEC METHOD 120 90 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE 60 Fig. 2-TYPICAL REVERSE CHARACTERISTICS 30 80 40 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz Fig. 3-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 210 CAPACITANCE, (pF) INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1000 16 200 160 120 80 40 UF1000 UF1008 2 5 20 50 100 200 500 REVERSE VOLTAGE, VOLTS UF1000 10 3 .0 UF1008 1 .0 0 .3 0 .1 0.0 3 0.6 0.8 1.0 1.2 1.4 1.8 FORWARD VOLTAGE, VOLTS Fig. 5-TYPICAL FORWARD CHARACTERISTICS Fig. 4-TYPICAL JUNCTION CAPACITANCE http://www.yeashin.com 20 0.0 1 0.4 0 1 INSTANTANEOUS FORWARD CURRENT, (A) PEAK FORWARD CURRENT, AMPERES Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 2 REV.02 20110725