AFBR-59E4APZ Multimode Small Form Factor (SFF) Transceiver for Fast Ethernet with LC connector Data Sheet Description Features The AFBR-59E4APZ is a new power saving Small Form Factor transceiver that gives the system designer a product to implement a range of solutions for multimode fiber Fast Ethernet. • Multisourced 2 x 5 package style • Operates with 62.5/125 µm and 50/125 µm multimode fiber • Single +3.3 V power supply • Wave solder and aqueous wash process compatibility • Manufactured in an ISO 9001 certified facility • Compatible with the optical performance requirements of 100Base-FX version of IEEE 802.3u • RoHS compliant • LVPECL Signal Detect Output • Temperature range: -40 °C to +85 °C This transceiver is supplied in the industry standard 2 x 5 DIP style with an LC fiber connector interface. Transmitter The transmitter section of the AFBR-59E4APZ transceiver utilizes a 1310 nm LED. This LED is packaged in the optical subassembly portion of the transmitter section. It is driven by an integrated circuit that converts differential LVPECL logical signals into an analog LED drive current. Receiver The receiver utilizes an InGaAs PIN photodiode coupled to a trans-impedance pre-amplifier IC. It is packaged in the optical subassembly of the receiver. The PIN/preamplifier combination is connected to a quantizer IC, which provides the final pulse shaping for data output. The data output is differential LVPECL. The Signal Detect output is single-ended. Both Data and Signal Detect outputs are LVPECL compatible. Application • Fast Ethernet Package Pin Descriptions The package outline drawing and pinout are shown in Figure 1 and Figure 5. The details of this package outline and pinout are compliant with the multisource definition of the 2 x 5 DIP. The low profile of the Avago transceiver design complies with the maximum height allowed for the LC connector over the entire length of the package. Pin 1 Receiver Signal Ground VEE RX: The optical subassemblies utilize a high-volume assembly process together with low-cost lens elements, which result in a cost-effective building block. The electrical subassembly consists of a high volume multilayer printed circuit board on which the ICs and various surface-mounted passive circuit elements are attached. Directly connect this pin to the receiver ground plane. Pin 2 Receiver Power Supply VCC RX: Provide +3.3 V DC via the recommended receiver power supply filter circuit. Locate the power supply filter circuit as close as possible to the VCC RX pin. Pin 3 Signal Detect SD: Normal optical input levels to the receiver result in a logic “1” output. Low optical input levels to the receiver result in a logic “0” output. The receiver and transmitter sections include an internal shield for the electrical and optical subassemblies to ensure high immunity to external EMI fields. Pin 4 Receiver Data Out Bar RD-: The outer housing including the LC ports is molded of filled nonconductive plastic to provide mechanical strength. The solder posts of the Avago design are isolated from the internal circuit of the transceiver. Pin 5 Receiver Data Out RD+: The transceiver is attached to a printed circuit board with the ten signal pins and the two solder posts, which exit the bottom of the housing. The two solder posts provide the primary mechanical strength to withstand the loads imposed on the transceiver by mating with the LC connector fiber cables. Provide +3.3 V DC via the recommended transmitter power supply filter circuit. Locate the power supply filter circuit as close as possible to the VCC TX pin. RX Signal AC coupled LVPECL. See Figure 2. Signal AC coupled LVPECL. See Figure 2. Pin 6 Transmitter Power Supply VCC TX: Pin 7 Transmitter Signal Ground VEE TX: Directly connect this pin to the transmitter ground plane. Pin 8 NC: TX Mounting Studs/Solder Posts Not connected. Pin 9 Transmitter Data In TD+: Signal AC coupled LVPECL. See Figure 2. Pin 10 Transmitter Data In Bar TD-: Top View Signal AC coupled LVPECL. See Figure 2. Mounting Studs/Solder Posts RECEIVER SIGNAL GROUND RECEIVER POWER SUPPLY SIGNAL DETECT RECEIVER DATA OUT BAR RECEIVER DATA OUT Figure 1. Pin Out Diagram 2 o o o o o 1 2 3 4 5 10 9 8 7 6 o o o o o TRANSMITTER DATA IN BAR TRANSMITTER DATA IN NC TRANSMITTER SIGNAL GROUND TRANSMITTER POWER SUPPLY The mounting studs are provided for transceiver mechanical attachment to the circuit board. It is recommended that you connect the holes in the circuit board to chassis ground. Application Information Shipping Container The Applications Engineering group is available to assist you with the technical understanding and design trade-offs associated with these transceivers. You can contact them through your Avago sales representative. The transceiver is packaged in a shipping container designed to protect it from mechanical and ESD damage during shipment of storage. The following information is provided to answer some of the most common questions about the use of these parts. Transceiver Optical Power Budget versus Link Length Optical Power Budget (OPB) is the available optical power for a fiber optic link to accommodate fiber cable losses plus losses due to in-line connectors, splices, optical switches, and to provide margin for link aging and unplanned losses due to cable plant reconfiguration or repair. Avago LED technology has produced 1300 nm LED devices with lower aging characteristics than normally associated with these technologies in the industry. The industry convention is 1.5 dB aging for 1300 nm LEDs. The 1300 nm Avago LEDs are specified to experience less than 1 dB of aging over normal commercial equipment mission life periods. Contact your Avago sales representative for additional details. Recommended Handing Precautions Avago recommends that normal status precautions be taken in the handling and assembly of these transceivers to prevent damage, which may be induced by electrostatic discharge (ESD). The AFBR-59E4APZ transceiver meets Jedec JESD22-A114 Class 2 products. Care should be used to avoid shorting the receiver data or signal detect outputs directly to ground without proper current limiting impedance. Solder and Wash Process Compatibility The transceivers are delivered with protective process plugs inserted into the LC receptacle. This process plug protects the optical subassemblies during wave solder and aqueous wash processing, and acts as a dust cover during shipping. These transceivers are compatible with either industry standard wave or hand solder processes. 3 Board Layout - Decoupling Circuit, Ground Planes and Termination Circuits To achieve optimum performance from these transceivers, do take care in the layout of your circuit board. Figure 2 provides a schematic for a recommended termination circuit that works well with these parts, It is further recommended that a contiguous ground plane be provided in the circuit board directly under the transceiver to provide a low-inductance ground for signal return current. This recommendation is in keeping with good high frequency board layout practices. Figure 3 shows a recommended power supply filter. Board Layout - Hole Pattern The Avago transceiver complies with the circuit board “Common Transceiver Footprint” hole pattern defined in the original multisource announcement that defined the 2 x 5 package style. This drawing is reproduced in Figure 5 with the addition of ANSI Y14.5M compliant dimensioning to be used as a guide in the mechanical layout of your circuit board. Figure 5 illustrates the recommended panel opening and the position of the circuit board with respect to this panel. Regulatory Compliance These transceiver products are intended to enable commercial system designers to develop equipment that complies with the various international regulations governing certification of Information Technology Equipment. See the Regulatory Compliance Table for details. Additional information is available from your Avago sales representative. AFBR-59E4APZ SerDes IC (AC Coupling Data) 50 Ω TX+ 100 nF i 50 Ω TX- i 100 nF 100Ω LED Driver LED 3.3 V 2.7 kΩ 50 Ω 2.7 kΩ RX+ 100 nF i 50 Ω 100 Ω RX- i 4.3 kΩ 4.3 kΩ GND AMPLIFIER & QUANTIZER 100 nF 150 Ω Control Logic SD PECL input 150 Ω GND 10 kΩ GND Note: Refer to SerDes supplier's recommendation regarding the interface between AFBR-59E4APZ and SerDes. The proposed termination is recommended for LVPECL AC-coupled signals. Other terminations could also be applicable, depending on the SerDes interface. Figure 2. Recommended Termination Circuit AFBR-59E4APZ 1 µH Vcc TX Vcc RX 0.1 µF 1 µH 0.1 µF 10 µF 0.1 µF 10 µF 3.3V Note: Inductors should have less than 1 Ω series resistor per MSA. Figure 3. Recommended Power Supply Filter 4 PD All dimensions are in millimeters (inches). Figure 4. Package Outline Drawing 5 20 x Ø 0.81 ± .10 (.032 ± .004) SEE DETAIL B 13.34 (.525) SEE NOTE 3 25.75 (1.014) 4 x Ø 1.40 ± .10 (NOTE 5) (.055 ± .004) SEE DETAIL A 12.16 (.479) 15.24 MIN. PITCH (.600) 54321 2 x Ø 2.29 MAX. (AREA FOR EYELET'S) (.090) 7.59 10.16 (.299) (.400) 6 7 8 9 10 2 x Ø 1.40 ± .10 (NOTE 4) (.055 ± .004) 3 (.118) 4.57 (.180) 3 (.118) 7.11 (.280) 3.56 (.140) 6 (.236) 8.89 (.350) 9X DETAIL A (3 x) 1.78 (.070) 1.8 .071 1 .039 15.24 MIN. PITCH (.600) + 1.50 - 0 (+.059) (.039) (- .000) DETAIL B (4 x) 1.00 A 14.22 ± .10 (.560 ± .004) TOP OF PCB A 10.16 ± .10 (.400 ± .004) +0 - 0.75 (+.000) (.620) (- .030) 15.75 A SECTION A - A Notes: 1. This page describes the recommended circuit board footprint and front panel openings for SFF transceivers. 2. The hatched areas are keep-out areas reserved for housing stand-offs. No metal traces are allowed in keep-out areas. 3. The drawing shows extra pin holes for 2x6 pin and 2x10 pin transceivers. These extra holes are not required for AFBR-59E4APZ and other 2x5 pin SFF modules. 4. Holes for mounting studs must not be tied to signal ground; they should be tied to chassis ground. 5. Holes for housing leads are not required for AFBR-59E4APZ. 6. All dimensions are in millimeters (inches). Figure 5. Recommended Board Layout Hole Pattern 6 Electrostatic Discharge (ESD) Immunity There are two design cases in which immunity to ESD damage is important. Equipment utilizing these transceivers will be subject to radio-frequency electromagnetic fields in some environments. These transceivers have a high immunity to such fields. The first case is when the transceiver is handled before it is mounted on the circuit board. Note: Use normal ESD handling precautions for ESD-sensitive devices. These precautions include using grounded wrist straps, work benches, and floor mats in ESD-controlled areas. The second case to consider is static discharges to the exterior of the equipment chassis that contains the transceiver parts. To the extent that the LC connector is exposed to the outside of the equipment chassis, it may be subject to whatever ESD system-level test criteria that the equipment is intended to meet. Electromagnetic Interference (EMI) Most equipment designs utilizing this high speed transceiver from Avago will be required to meet the requirements of FCC in the United States, and CENELEC EN55022 (CISPR 22) in Europe. 7 For additional information regarding EMI, susceptibility, ESD and conducted noise testing procedures and results, refer to Application Note 1166, Minimizing Radiated Emissions of High-Speed Data Communications Systems. Transceiver Reliability and Performance Qualification Data The 2 x 5 transceivers have passed Avago reliability and performance qualification testing and are undergoing ongoing quality and reliability monitoring. Details are available from your Avago sales representative. Regulatory Compliance Table Feature Test Method Performance Electrostatic Discharge (ESD) to the Electrical Pins JEDEC JESD22-A114 Meets Class 2 (2000 to 3999 V).Withstand up to 2000 V applied between electrical pins. Electrostatic Discharge Variation of IEC 61000-4-2 (ESD) to the LC Receptacle Typically withstand at least 9 kV without damage when the LC connector receptacle is contacted by a Human Body Model probe. Typically withstand 15 kV air discharge on LC-connector receptacle. Electromagnetic Interference (EMI) FCC Class B CENELEC CEN55022 Class B Transceivers typically provide a 10 dB margin to the noted standard limits when tested at a certified test range with the transceiver mounted to a circuit card. Immunity Variation of IEC 61000-4-3 Typically show no measurable effect from a 10 V/m field swept from 80 MHz to 1 GHz applied to the transceiver when mounted to a circuit card withouta chassis enclosure. Eye Safety EN 60950-1:2006+A11+A1+A12 EN 60825-1:2007 EN 60825-2:2004+A1+A2 Compliant per Avago testing under single fault conditions. TUV Certification - R 50236535 0003 Component Recognition Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information Technology Equipment including Electrical Business Equipment UL File #: E173874 , Vol. 1 RoHS Compliance 8 Reference to RoHS Directive 2011/65EU Annex II Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not be assumed that limiting values of more than one parameter can be applied to the product at the same time. Exposure to the absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Minimum Storage Temperature TS -40 Lead Soldering Temperature Typical Maximum Unit +100 °C TSOLD +260 °C Lead Soldering Time tSOLD 10 sec Supply Voltage VCC -0.5 3.63 V Data Input Voltage VI -0.5 VCC V Differential Input Voltage (p-p) VD 1.9 V Maximum Unit +85 °C 3.6 V Notes 8 Recommended Operating Conditions Parameter Symbol Minimum Typical Case Operating Temperature TC -40 Supply Voltage VCC 3.0 Data Output Load RL 100 W Signaling Rate B 125 MBd 1 3.3 Notes Transmitter Electrical Characteristics Parameter Symbol Typical Maximum Unit Notes Supply Current ICC Minimum 80 120 mA 2 Power Dissipation PDISS 270 440 mW Differential Input Voltage VDIFF 1.0 1.6 V 3 Input Differential Impedance RIN W 4 Notes 0.8 100 Receiver Electrical Characteristics Parameter Symbol Typical Maximum Units Supply Current ICC 65 85 mA Power Dissipation PDISS 215 310 mW 2.0 V Data Output: Differential Output Voltage (RD+/-) |VOH - VOL| Minimum 0.4 5, 6 Data Output Rise Time (10%-90%) tr 2.2 ns Data Output Fall Time (10%-90%) tf 2.2 ns Signal Detect Output Voltage - Low SDVOL Vdd - 1.81 Vdd - 1.62 V 7 Signal Detect Output Voltage - High SDVOH Vdd - 1.02 Vdd - 0.88 V 7 Notes: 1. Fast Ethernet 4B/5B. 2. Typical Values are for room temperature at 3.3 V. 3. Peak to Peak. 4. Tx data inputs are AC coupled. 5. Differential output voltage is internally AC-coupled. The low and high voltages are measured using 100 Ω differential termination. 6. RD+ and RD- outputs are squelched at SD de-assert level. 7. Measured with an external 10 kΩ resistor to ground. 8. Moisture sensitivity level is MSL-1. 9 Transmitter Optical Characteristics Parameter Symbol Minimum Typical Maximum Units Notes Output Optical Power 62.5/125 µm, NA = 0.275 Fiber PO -20.0 -14.0 dBm 2, 5 Output Optical Power 50/125 µm, NA = 0.20 Fiber PO -23.5 -14.0 dBm 2, 5 Extinction Ratio ER 10 Center Wavelength lC 1270 Spectral Width - FWHM Dl Optical Rise Time (10%-90%) tr 0.6 1.0 3.0 ns Optical Fall Time (10%-90%) tf 0.6 1.0 3.0 ns Duty Cycle Distortion Contributed by the Transmitter DCD 0.6 ns 3 Data Dependent Jitter Contributed by the Transmitter DDJ 0.6 ns 3 Random Jitter Contributed by the Transmitter RJ 0.69 ns 1, 3 Maximum Units Notes 4, 5 -16.5 dB 1308 1380 147 nm nm Receiver Optical and Electrical Characteristics Parameter Symbol Minimum Typical Input Optical Power PIN -31 -14 dBm Operating Wavelength l 1270 1380 nm Duty Cycle Distortion Contributed by the Receiver DCD 0.4 ns 3, 6 Data Dependent Jitter Contributed by the Receiver DDJ 1.0 ns 3 Random Jitter Contributed by the Receiver RJ 2.14 ns 1, 3 Signal Detect - Assert SDA -33.0 dBm 5 Signal Detect - Deassert SDD -45.0 dBm 5 Signal Detect - Hysteresis SDD - SDA 0.5 Signal Detect Assert Time (off to on) SDon 0 100 µs 7 Signal Detect Deassert Time (on to off ) SDoff 0 350 µs 8 1.9 dB Notes: 1. Peak to Peak. 2. Optical values are measured over the specified operating voltage and temperature ranges. The average power can be converted to a peak value by adding 3 dB. 3. Characterized with 125 MBd, PRBS27-1 pattern. 4. This specification is intended to indicate the performance of the receiver section of the transceiver when Optical Input Power signal characteristics are present per the following definitions • Over the specified operating temperature and voltage ranges • Bit Error Rate (BER) is better than or equal to 1x10-10 • Transmitter is operating to simulate any cross-talk present between the transmitter and receiver sections of the transceiver. 5.Average 6. Duty Cycle Distortion contributed by the receiver is measured at 50% threshold of the electrical signal. The input optical power level is -20 dBm average. 7. Signal Detect output shall be asserted within the specified time after a step increase of the Optical Input Power. 8. Signal Detect output shall be de-asserted within the specified time after a step decrease of the Optical Input Power. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. AV02-4197EN - July 16, 2013