SLVS401 − AUGUST 2001
FEATURES
D Complete Power Management Solution for
D
D
D
D
D
D
D
D
D
DESCRIPTION
The TPS2149 incorporates two power distribution
switches and an LDO in one small package, providing
a USB bus-powered hub power management solution
that saves up to 60% in board space over typical
implementations.
USB Bus-Powered Hubs
3.3-V 200 mA Low-Dropout Voltage Regulator
Two 5-V 340-mΩ (Typ) High-Side MOSFETs
Independent Thermal- and Short-Circuit
Protection for LDO and Each Switch
Overcurrent Indicator With Transient Filter
2.9-V to 5.5-V Operating Range
CMOS- and TTL-Compatible Enable Inputs
75-µA (Typ) Supply Current
Available in 8-Pin MSOP (PowerPAD)
−40°C to 85°C Ambient Temperature Range
The TPS2149 meets USB 2.0 bus-powered hub
requirements. An integrated LDO regulates the 5-V bus
power down to 3.3 V for the USB controller. The two
MOSFET switches provide power to the downstream
ports. With independent enables, the downstream ports
remain unpowered until the hub completes
enumeration.
Each power-distribution switch is capable of supplying
200 mA of continuous current, and the independent
logic enables are compatible with 5-V logic and 3-V
logic. The switches and the LDO are designed with
controlled rise times and fall times to minimize current
surges.
APPLICATIONS
D USB Bus-Powered Hubs
− Keyboards
− Monitors
− Hub Boxes
The TPS2149 has active-low enables while the
TPS2159 has active-high enables.
LDO and dual switch family selection guide and schematics
TPS2145/55
TSSOP−14
VIN/SW1
LDO_EN
EN1
SW2
EN2
GND
LDO
TPS2147/57
MSOP−10
LDO_OUT
VIN/SW1
LDO_ADJ
LDO
VIN/SW1
OC1
OC1
OUT1
OUT1
OUT2
OC2
EN1
SW2
EN2
GND
LDO
LDO_OUT
OUT2
OC2
LDO_EN
EN2
EN1
GND
TPS2149/59
MSOP−8
TPS2148/58
MSOP−8
LDO_OUT
VIN
LDO
LDO_OUT
OUT2
OUT1
EN1
OUT1
OC
OUT2
EN2
GND
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
!"#$%! & '("")% $& ! *(+,'$%! -$%)
"!-('%& '!!"# %! &*)''$%!& *)" %.) %)"#& ! )/$& &%"(#)%&
&%$-$"- 0$""$%1
"!-('%! *"!')&&2 -!)& !% )')&&$",1 ',(-)
%)&%2 ! $,, *$"$#)%)"&
Copyright 2001, Texas Instruments Incorporated
www.ti.com
1
SLVS401 − AUGUST 2001
AVAILABLE OPTIONS
TA
PACKAGE
AND PIN
COUNT
DESCRIPTION
−40°C to 85°C
PACKAGED DEVICES
ACTIVE LOW
(SWITCH)
ACTIVE HIGH
(SWITCH)
Adjustable LDO with LDO enable
TSSOP-14
TPS2145IPWP
TPS2155IPWP
3.3-V fixed LDO
MSOP-10
TPS2147IDGQ
TPS2157IDGQ
3.3-V Fixed LDO with LDO enable and LDO output
switch
MSOP-8
TPS2148IDGN
TPS2158IDGN
3.3-V Fixed LDO, shared input with switches
MSOP-8
TPS2149IDGN
TPS2159IDGN
NOTE: All options available taped and reeled. Add an R suffix (e.g. TPS2145IPWPR)
TPS2149, TPS2159
MSOP (DGN) PACKAGE
(TOP VIEW)
OUT1
VIN
LDO_OUT
OUT2
1
8
2
7
3
6
4
5
EN1†
EN2†
OC
GND
† Pins 7 and 8 are active high for TPS2159.
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Input voltage range: VI(VIN),VI(ENx), . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Output voltage range: VO(OUTx), VO(LDO_OUT), VO(OC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Maximum output current, IO(OC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA
Continuous output current, IO(OUT), IO(LDO_OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating virtual-junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 110°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Electrostatic discharge (ESD) protection: Human body model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
Charged device model (CDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 kV
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡ All voltages are with respect to GND.
DISSIPATION RATING TABLE
2
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
MSOP8
1455.5 mW
17.1 mW/°C
684.9 mW
428.08 mW
www.ti.com
SLVS401 − AUGUST 2001
recommended operating conditions
VI(VIN)
VI(ENx)
Input voltage
Continuous output current, IO
Output current limit, IO(LMT)
MIN
MAX
2.9
5.5
0
5.5
LDO_OUT
200
OUT1, OUT2
150
UNIT
V
mA
LDO_OUT
250
450
OUT1, OUT2
200
400
−40
100
°C
MAX
UNIT
VI(ENx) = 5 V (inactive),
VO(LDO_OUT) = no load,
VO(OUTx) = no load
100
µA
VI(ENx) = 5 V (inactive),
VO(LDO_OUT) = no load,
VO(OUTx) = 0 V
(measured from outputs to
ground)
1
µA
ENx = on (active)
150
µA
ENx = off (inactive)
100
µA
MAX
UNIT
Operating virtual-junction temperature range, TJ
mA
electrical characteristics over recommended operating junction-temperature range,
2.9 V ≤ VI(VIN) ≤ 5.5 V, TJ = −40°C to 100°C (unless otherwise noted)
general
PARAMETER
TEST CONDITIONS
Off-state supply current
VI(VIN) = 5 V
Forward leakage current (power
switches only)
II
Total input current at VIN
VI(VIN) = 5 V,
No load on OUTx,
No load on LDO_OUT
MIN
TYP
power switches
PARAMETER
rDS(on)
Ilkg(R)
IOS
Static drain-source
on-state resistance,
VIN to OUTx
Reverse leakage current at OUTx
TEST CONDITIONS
MIN
TYP
IO(LDO_OUT) = 200 mA,
IOUT1 and IOUT2 = 150 mA, TJ = −40°C to 100°C
680
mΩ
IO(LDO_OUT) = 200 mA,
IOUT1 and IOUT2 = 150 mA, TJ = 25°C
VO(OUTx) = 5 V
340
VI(ENx) = 5 V, VI(ENx) = 0 V,
VI(VIN) = 5 V
10
VI(ENx) = 5 V, VI(ENx) = 0 V,
VI(VIN) = 2.9 V
10
VI(ENx) = 5 V, VI(ENx) = 0 V,
VI(VIN) = 0 V
10
µA
Short circuit output current
OUTx connected to GND, device enabled into short
circuit
Delay time for asserting OC flag
From IOUTx at 95% of current limit level to 50% OC.
5.5
ms
Delay time for deasserting OC flag
From IOUTx at 95% of current limit level to 50% OC.
10.5
ms
0.2
0.4
A
NOTE 1: Specified by design, not tested in production.
www.ti.com
3
SLVS401 − AUGUST 2001
electrical characteristics over recommended operating junction-temperature range,
2.9 V ≤ VI(VIN) ≤ 5.5 V, TJ = −40°C to 100°C (unless otherwise noted)
timing parameters, power switches
PARAMETER
TEST CONDITIONS
ton
Turnon time, OUTx switch, (see Note 1)
CL = 100 µF
CL = 1 µF
RL = 33 Ω
toff
Turnoff time, OUTx switch (see Note 1)
CL = 100 µF
CL = 1 µF
RL = 33 Ω
tr
Rise time, OUTx switch (see Note 1)
tf
CL = 100 µF
CL = 1 µF
CL = 100 µF
Fall time, OUTx switch (see Note 1)
CL = 1 µF
RL = 33 Ω
RL = 33 Ω
MIN
TYP
MAX
0.5
6
0.1
3
5.5
10
0.05
2
0.5
5
0.1
2
5.5
9
0.05
1.2
UNIT
ms
NOTE 1. Specified by design, not tested in production.
undervoltage lockout at VIN
PARAMETER
TEST CONDITIONS
UVLO Threshold
MIN
TYP
2.2
Hysteresis (see Note 1)
MAX
2.85
260
Deglitch (see Note 1)
UNIT
V
mV
µs
50
NOTE 1. Specified by design, not tested in production.
electrical characteristics over recommended operating junction-temperature range,
2.9 V ≤ VI(VIN) ≤ 5.5 V, VI(ENx) = 0 V, VI(LDO_EN) = 5 V, CL(LDO_OUT) = 10 µF, TJ = −40°C to 100°C
(unless otherwise noted)
3.3 V LDO
PARAMETER
VO
TEST CONDITIONS†
Output voltage, dc
VI(VIN) = 4.25 V to 5.25 V,
IO(LDO_OUT) = 0.5 mA to 200 mA
Dropout voltage
VI(VIN) = 3.2 V, IO(OUT1) = 150 mA,
IO(LDO_OUT) = 200 mA
Line regulation voltage (see Note 1)
Load regulation voltage (see Note 1)
IOS
Short-circuit current limit
Ilkg(R)
Reverse leakage current into
LDO_OUT
MIN
TYP
MAX
UNIT
3.20
3.3
3.40
V
0.35
V
0.1
%/V
VI(VIN) = 4.25 V to 5.25 V, IO(LDO_OUT) = 5 mA
VI(VIN) = 4.25 V, IO(LDO_OUT) = 5 mA to 200 mA
VI(VIN) = 4.25 V, LDO_OUT connected to GND
VO(LDO_OUT) = 3.3 V, VI(IN) = 0 V
0.275
0.4
1%
0.33
0.55
A
10
µA
VO(LDO_OUT) = 5.5 V, VI(IN) = 0 V
10
µA
Power supply rejection
f = 1 kHz, CL(LDO_OUT) = 4.7 µF, ESR = 0.25 Ω,
IO = 5 mA, VINp−p = 100 mV
50
dB
Ramp-up time, LDO_OUT (0% to 90%)
VIN ramping up from 10% to 90% in 0.1 ms,
RL = 16 Ω, CL(LDO_OUT) = 10 µF
0.1
1
ms
† Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately.
NOTES: 1. Specified by design, not tested in production.
4
www.ti.com
SLVS401 − AUGUST 2001
electrical characteristics over recommended operating junction-temperature range,
2.9 V ≤ VI(VIN) ≤ 5.5 V, VI(ENx) = 0 V, TJ = −40°C to 100°C (unless otherwise noted)
enable input, ENx (active low)
PARAMETER
VIH
VIL
High-level input voltage
II
Input current, pullup (source)
TEST CONDITIONS
MIN
TYP
MAX
2
UNIT
V
Low-level input voltage
VI(ENx) = 0 V
0.8
V
5
µA
enable input, ENx (active high)
PARAMETER
VIH
VIL
High-level input voltage
II
Input current, pulldown (sink)
TEST CONDITIONS
MIN
TYP
MAX
2
UNIT
V
Low-level input voltage
VI(ENx) = 5 V
0.8
V
5
µA
logic output, OC
PARAMETER
TEST CONDITIONS
Current sinking at VO = 0.4 V
MIN
TYP
MAX
1
UNIT
mA
thermal shutdown characteristics
PARAMETER
First thermal shutdown (shuts down switch or regulator
in overcurrent)
TEST CONDITIONS
Occurs at or above specified temperature
when overcurrent is present.
Recovery from thermal shutdown
Second thermal shutdown (shuts down all switches and
regulator)
MIN
TYP
Second thermal shutdown hysteresis
UNIT
120
110
Occurs on rising temperature, irrespective of
overcurrent.
MAX
°C
155
10
www.ti.com
5
SLVS401 − AUGUST 2001
TPS2149 functional block diagram
3.3 V / 200 mA
LDO
VIN
LDO_OUT
CS
Charge
Pump
OUT1
Current
Limit
Driver
OC
EN1
Thermal
Sense
OUT2
CS
Current
Limit
Driver
EN2
Thermal
Sense
GND
Terminal Functions
TERMINAL
NAME
NO.
TPS2149
EN1
EN1
I/O
DESCRIPTION
TPS2159
8
I
Logic level enable to transfer power to OUT1
7
I
Logic level enable to transfer power to OUT2
8
EN2
EN2
7
GND
5
5
LDO_OUT
3
3
O
LDO output
OC
6
6
O
Overcurrent status flag for OUT1 and OUT2. Open drain output.
OUT1
1
1
O
Switch 1 output
OUT2
4
4
VIN
2
2
6
Ground
Switch 2 output
I
Input for LDO switch 1 and switch 2; device supply voltage
www.ti.com
SLVS401 − AUGUST 2001
detailed description
VIN
The VIN serves as the input to the internal LDO and as the input to both N-channel MOSFETs. The 3.3-V LDO
has a dropout voltage of 0.35 V and is rated for 200 mA of continuous current. The power switches are N-channel
MOSFETs with a maximum on-state resistance of 580 mΩ per switch. Configured as high-side switches, the
power switches prevent current flow from OUT to IN and IN to OUT when disabled. The power switches are rated
at 150 mA, continuous current.
OUTx
OUT1 and OUT2 are the outputs from the internal power-distribution switches.
LDO_OUT
LDO_OUT is the output of the internal 200-mA LDO.
enable (ENx, ENx)
The logic enable disables the power switch. Both switches have independent enables and are compatible with
both TTL and CMOS logic.
overcurrent (OC)
The OC open drain output is asserted (active low) when an overcurrent or overtemperature condition is
encountered. The output will remain asserted until the overcurrent or overtemperature condition is removed.
current sense
A sense FET monitors the current supplied to the load. Current is measured more efficiently by the sense FET
than by conventional resistance methods. When an overload or short circuit is encountered, the current-sense
circuitry sends a control signal to the driver. The driver in turn reduces the gate voltage and drives the power
FET into its saturation region, which switches the output into a constant-current mode and holds the current
constant while varying the voltage on the load.
thermal sense
A dual-threshold thermal trip is implemented to allow fully independent operation of the power distribution
switches. In an overcurrent or short-circuit condition, the junction temperature rises. When the die temperature
rises to approximately 120°C, the internal thermal sense circuitry determines which power switch is in an
overcurrent condition and turns off that switch, thus isolating the fault without interrupting operation of the
adjacent power switch. Because hysteresis is built into the thermal sense, the switch turns back on after the
device has cooled approximately 10 degrees. The switch continues to cycle off and on until the fault is removed.
undervoltage lockout
A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2.5 V, a control
signal turns off the power switch.
www.ti.com
7
SLVS401 − AUGUST 2001
PARAMETER MEASUREMENT INFORMATION
50%
VI(ENx)
50%
tpd(off)
ton
toff
tpd(on)
90%
VO(OUTx)
90%
10%
10%
tr
tf
90%
VO(OUTx)
90%
10%
10%
TIMING
Figure 1. Timing and Internal Voltage Regulator Transition Waveforms
TYPICAL CHARACTERISTICS
SWITCH TURNON DELAY AND RISE TIME
WITH 1-µF LOAD
SWITCH TURNOFF DELAY AND FALL TIME
WITH 1-µF LOAD
VI(EN)
(5 V/div)
VI(EN)
(5 V/div)
VO(OUT)
(2 V/div)
VO(OUT)
(2 V/div)
VI = 5 V
TA = 25°C
CL = 1 µF
RL = 25 Ω
VI = 5 V
TA = 25°C
CL = 1 µF
RL = 25 Ω
0
0.4
0.8 1.2
1.6 2 2.4 2.8
t − Time − ms
3.2
3.6
4.2
Figure 2
8
0
0.4
0.8 1.2
1.6 2 2.4 2.8
t − Time − ms
Figure 3
www.ti.com
3.2
3.6
4.2
SLVS401 − AUGUST 2001
TYPICAL CHARACTERISTICS
SWITCH TURNOFF DELAY AND FALL TIME
WITH 120-µF LOAD
SWITCH TURNON DELAY AND RISE TIME
WITH 120-µF LOAD
VI(EN)
(5 V/div)
VI(EN)
(5 V/div)
VO(OUT)
(2 V/div)
VO(OUT)
(2 V/div)
VI = 5 V
TA = 25°C
CL = 120 µF
RL = 25 Ω
VI = 5 V
TA = 25°C
CL = 120 µF
RL = 25 Ω
0
2
4
6
8 10 12 14
t − Time − ms
16
18
0
20
4
Figure 4
8
12
16 20 24 28
t − Time − ms
32
36
40
Figure 5
SHORT-CIRCUIT CURRENT, SWITCH
ENABLED INTO A SHORT
LDO TURNON DELAY AND RISE TIME
WITH 4.7-µF LOAD
VI(EN)
(5 V/div)
VI = 5 V
TA = 25°C
CL = 4.7 µF
RL = 13.2 Ω
VI(LDO_EN)
(5 V/div)
VO(LDO_OUT)
(1 V/div
IO(OUT)
(100 mA/div)
0
1
2
3
4
5
6
t − Time − ms
7
8
9
10
Figure 6
0
0.4
0.8 1.2
1.6 2 2.4 2.8
t − Time − ms
3.2
3.6 4.2
Figure 7
www.ti.com
9
SLVS401 − AUGUST 2001
TYPICAL CHARACTERISTICS
LOAD TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
IO(LDO_OUT)
5.25 V
VI(VIN)
4.25 V
(200 mA/div)
∆VO(LDO_OUT)
(100 mV/div)
∆VO(LDO_OUT)
(0.05 V/div)
TA = 25°C
CL(LDO_OUT) = 4.7 µF
ESR = 1 Ω
IO(LDO_OUT) = 200 mA
0
TA = 25°C
CL(LDO_OUT) = 4.7 µF
ESR = 1 Ω
0
100 200 300 400 500 600 700 800 900 1000
t − Time − µs
100 200 300 400 500 600 700 800 900 1000
t − Time − µs
Figure 9
Figure 8
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
140
140
120
120
I DD − Supply Current − µ A
I DD − Supply Current − µ A
SUPPLY CURRENT
vs
JUNCTION TEMPERATURE
100
80
60
40
−20
0
20
40
60
80
100
TJ − Temperature − °C
Figure 10
10
80
60
40
20
20
0
−40
100
0
2.5
3
3.5
4
4.5
VCC − Supply Voltage − V
Figure 11
www.ti.com
5
5.5
SLVS401 − AUGUST 2001
rDS(on) − Static Drain-Source On-State Resistance − Ω
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
JUNCTION TEMPERATURE
0.6
0.55
0.5
0.45
SW1
0.4
SW2
0.35
0.3
0.25
0.2
0.15
0.1
−40
−20
0
20
40
60
80
TJ − Junction Temperature − °C
100
rDS(on) − Static Drain-Source On-State Resistance − Ω
TYPICAL CHARACTERISTICS
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
SUPPLY VOLTAGE
0.38
0.37
0.36
0.35
SW1
0.34
SW2
0.33
0.32
0.31
0.3
2.5
3
Figure 12
380
380
360
360
Short Circuit Current − mA
Short Circuit Current − mA
400
340
320
SW1
280
SW2
260
5
5.5
340
320
SW1
300
280
240
220
220
0
20
40
60
80
TJ − Free-Air Temperature − °C
100
Figure 14
SW2
260
240
−20
5.5
SHORT CIRCUIT CURRENT
vs
SUPPLY VOLTAGE
400
200
−40
5
Figure 13
SHORT CIRCUIT CURRENT
vs
JUNCTION TEMPERATURE
300
3.5
4
4.5
VCC − Supply Voltage
200
2.5
3
3.5
4
4.5
VCC − Supply Voltage
Figure 15
www.ti.com
11
SLVS401 − AUGUST 2001
TYPICAL CHARACTERISTICS
UNDERVOLTAGE LOCKOUT
vs
JUNCTION TEMPERATURE
2.9
UVLO − Undervoltage Lockout − V
2.8
Rising
2.7
2.6
2.5
Falling
2.4
2.3
2.2
2.1
−40 −25 −10
5 20 35 50 65 80
TJ − Junction Temperature − °C
95 110
Figure 16
APPLICATION INFORMATION
external capacitor requirements on power lines
A ceramic bypass capacitor (0.01-µF to 0.1-µF) between VIN and GND, close to the device, is recommended
to improve load transient response and noise rejection.
A bulk capacitor (4.7-µF ) between VIN and GND is also recommended, especially if load transients in the
hundreds of milliamps with fast rise times are anticipated.
A 66-µF bulk capacitor is recommended from OUTx to ground, especially when the output load is heavy. This
precaution helps reduce transients seen on the power rails. Additionally, bypassing the outputs with a 0.1-µF
ceramic capacitor improves the immunity of the device to short-circuit transients.
LDO output capacitor requirements
Stabilizing the internal control loop requires an output capacitor connected between LDO_OUT and GND. The
minimum recommended capacitance is a 4.7 µF with an ESR value between 200 mΩ and 10 Ω. Solid tantalum
electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided they meet the
ESR requirements.
overcurrent
A sense FET is used to measure current through the device. Unlike current-sense resistors, sense FETs do not
increase the series resistance of the current path. When an overcurrent condition is detected, the device
maintains a constant output current. Complete shut down occurs only if the fault is present long enough to
activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output is shorted before the device is
enabled or before VIN has been applied. The TPS2149 and TPS2159 sense the short and immediately switches
to a constant-current output.
12
www.ti.com
SLVS401 − AUGUST 2001
APPLICATION INFORMATION
overcurrent (continued)
In the second condition, the short occurs while the device is enabled. At the instant the short occurs, very high
currents may flow for a very short time before the current-limit circuit can react. After the current-limit circuit has
tripped (reached the overcurrent trip threshold), the device switches into constant-current mode.
In the third condition, the load has been gradually increased beyond the recommended operating current. The
current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is
exceeded. The TPS2149 and TPS2159 are capable of delivering current up to the current-limit threshold without
damaging the device. Once the threshold has been reached, the device switches into its constant-current mode.
OC response
The OC open-drain output is asserted (active low) when an overcurrent condition is encountered. The output
will remain asserted until the overcurrent condition is removed. Connecting a heavy capacitive load to an
enabled device can cause momentary false overcurrent reporting from the inrush current flowing through the
device, charging the downstream capacitor. The TPS2149 and TPS2159 are designed to reduce false
overcurrent reporting. An internal overcurrent transient filter eliminates the need for external components to
remove unwanted pulses. Using low-ESR electrolytic capacitors on OUTx lowers the inrush current flow through
the device during hot-plug events by providing a low-impedance energy source, also reducing erroneous
overcurrent reporting.
power dissipation and junction temperature
The main source of power dissipation for the TPS2149 and TPS2159 comes from the internal voltage regulator
and the N-channel MOSFETs. Checking the power dissipation and junction temperature is always a good
design practice and it starts with determining the rDS(on) of the N-channel MOSFET according to the input voltage
and operating temperature. As an initial estimate, use the highest operating ambient temperature of interest and
read rDS(on) from the graphs shown in the Typical Characteristics section of this data sheet. Using this value,
the power dissipation per switch can be calculated using:
P D + r DS(on)
I2
(1)
Multiply this number by two to get the total power dissipation coming from the N-channel MOSFETs.
The power dissipation for the internal voltage regulator is calculated using:
ǒ
P D + V –V
I O(min)
Ǔ
I
O
(2)
The total power dissipation for the device becomes:
P D(total) + P
D(voltage regulator)
ǒ
) 2
P
D(switch)
Ǔ
(3)
Finally, calculate the junction temperature:
TJ + PD
R qJA ) T A
(4)
Where:
TA = Ambient temperature °C
RθJA = Thermal resistance °C/W, equal to inverting the derating factor found on the power dissipation
table in this datasheet.
www.ti.com
13
SLVS401 − AUGUST 2001
APPLICATION INFORMATION
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,
repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally
sufficient to get a reasonable answer.
thermal protection
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for
extended periods of time. The faults force the TPS2149 and TPS2159 into constant-current mode at first, which
causes the voltage across the high-side switch to increase; under short-circuit conditions, the voltage across
the switch is equal to the input voltage. The increased dissipation causes the junction temperature to rise to high
levels.
The protection circuit senses the junction temperature of the switch and shuts it off. Hysteresis is built into the
thermal sense circuit, and after the device has cooled approximately 10 degrees, the switch turns back on. The
switch continues to cycle in this manner until the load fault or input power is removed.
The TPS2149 and TPS2159 implement a dual thermal trip to allow fully independent operation of the power
distribution switches. In an overcurrent or short-circuit condition the junction temperature will rise. Once the die
temperature rises to approximately 120°C, the internal thermal sense circuitry checks which power switch is
in an overcurrent condition and turns that power switch off, thus isolating the fault without interrupting operation
of the adjacent power switch. Should the die temperature exceed the first thermal trip point of 120°C and reach
155°C, the device will turn off.
undervoltage lockout (UVLO)
An undervoltage lockout ensures that the device (LDO and switches) is in the off state at power up. The UVLO
will also keep the device from being turned on until the power supply has reached the start threshold (see
undervoltage lockout table), even if the switches are enabled. The UVLO will also be activated whenever the
input voltage falls below the stop threshold as defined in the undervoltage lockout table. This facilitates the
design of hot-insertion systems where it is not possible to turn off the power switches before input power is
removed. Upon reinsertion, the power switches will be turned on with a controlled rise time to reduce EMI and
voltage overshoots.
universal serial bus (USB) applications
The universal serial bus (USB) interface is a multiplexed serial bus operating at either 12 Mb/s, or 1.5 Mb/s for
USB 1.1, or 480 Mb/s for USB 2.0. The USB interface is designed to accommodate the bandwidth required by
PC peripherals such as keyboards, printers, scanners, and mice. The four-wire USB interface was conceived
for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for differential data, and two
lines are provided for 5-V power distribution.
USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power
is distributed through more than one hub or across long cables. Each function must provide its own regulated
3.3 V from the 5-V input or its own internal power supply.
The USB specification defines the following five classes of devices, each differentiated by power-consumption
requirements:
•
•
•
•
•
14
Hosts/self-powered hubs (SPH)
Bus-powered hubs (BPH)
Low-power, bus-powered functions
High-power, bus-powered functions
Self-powered functions
www.ti.com
SLVS401 − AUGUST 2001
APPLICATION INFORMATION
universal serial bus (USB) applications (continued)
The TPS2149 and TPS2159 are well suited for USB bus-powered hub applications. The internal LDO can be
used to provide the 3.3 V power needed by the controller while the dual switches distribute power to the
downstream functions.
USB power distribution requirements
USB can be implemented in several ways, and, regardless of the type of USB device being developed, several
power-distribution features must be implemented.
•
Hosts/self-powered hubs must:
−
−
Current-limit downstream ports
Report overcurrent conditions on USB VBUS
D Bus-powered hubs must:
−
−
−
Enable/disable power to downstream ports
Power up at <100 mA
Limit inrush current (<44 Ω and 10 µF)
D Functions must:
−
−
Limit inrush currents
Power up at <100 mA
The feature set of the TPS2149 and TPS2159 is designed to help USB bus-powered hubs meet the
requirements. The integrated current-limiting and overcurrent reporting is required by hosts and self-powered
hubs. The logic-level enable and controlled rise times meet the need of both input and output ports on
bus-powered hubs, as well as the input ports for bus-powered functions.
USB applications
Figure 17 shows the TPS2149 being used in a USB bus-powered two-port hub design. The internal 3.3-V LDO
is used to provide power for the USB function controller as well as to the 1.5-kΩ pullup resistor.
Switches 1 and 2 provide power to the downstream ports. Both are separately enabled to control power being
sent downstream. They are also disabled during enumeration to satisfy the 100 mA requirement.
Figure 18 shows the TPS2149 being used in a USB bus-powered four-port hub design. The internal 3.3-V LDO
is used to provide power for the USB function controller as well as to the 1.5 kΩ pullup resistor.
www.ti.com
15
SLVS401 − AUGUST 2001
APPLICATION INFORMATION
Upstream Port
USB Hub Controller
D+
D−
DP0
DM0
GND
D+
D−
DP1
DM1
C
D
A
B
A
B
VCC_3.3 V
0.1 µF
0.1 µF
DP3
DM3
GND
SN75240
A
B
33 pF
1.5 kΩ
XTAL2
5V
C
D
68 µF
DP4
DM4
D+
D−
TPS2149
GND
GND
5V
68 µF
D+
D−
6 MHz
1.5 kΩ
C
D
DP2
DM2
XTAL1
33 pF
10 µF
GND
SN75240
SN75240
5V
Downstream Port
PWRON1
EN1
OUT1
PWRON2
OVRCUR
EN2
OUT2
OC
GND
5V
68 µF
D+
D−
3.3 V_OUT
10 µF
0.1 µF
GND
VIN
5V
68 µF
Figure 17. Example of a Two Port Hub Design With TPS2149
16
www.ti.com
SLVS401 − AUGUST 2001
APPLICATION INFORMATION
Upstream Port
USB Hub Controller
D+
D−
DP0
DP1
DM0
DM1
5V
D+
D−
SN75240
SN75240
GND
Downstream Port
A
C
A
C
B
D
B
D
GND
5V
68 µF
VCC_3.3 V
0.1 µF
0.1 µF
DP1
D+
DM1
D−
XTAL1
33 pF
GND
6 MHz
10 µF
33 pF
1.5 kΩ
TPS2149
GND
GND
1.5 kΩ
5V
XTAL2
PWRON1
EN1
OUT1
PWRON2
OVRCUR
EN2
OUT2
68 µF
OC
3.3 V_OUT
10 µF
0.1 µF
VIN
Figure 18. Example of a 4 Port Hub Design With TPS2149
www.ti.com
17
PACKAGE OPTION ADDENDUM
www.ti.com
21-Mar-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPS2149IDGN
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AXD
TPS2149IDGNG4
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AXD
TPS2149IDGNR
OBSOLETE
MSOPPowerPAD
DGN
8
TBD
Call TI
Call TI
-40 to 85
AXD
TPS2149IDGNRG4
OBSOLETE
MSOPPowerPAD
DGN
8
TBD
Call TI
Call TI
-40 to 85
TPS2159IDGN
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AXE
TPS2159IDGNG4
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
AXE
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
21-Mar-2013
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated