TI TPS2068IDGNRQ1

TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
CURRENT-LIMITED POWER-DISTRIBUTION SWITCH
Check for Samples: TPS2068-Q1
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
2
Qualified for Automotive Applications
70-mΩ High-Side MOSFET
1.5-A Continuous Current
Thermal and Short-Circuit Protection
Accurate Current Limit (1.6 A Min, 2.6 A Max)
Operating Range: 2.7 V to 5.5 V
0.6-ms Typical Rise Time
Undervoltage Lockout
Deglitched Fault Report (OC)
No OC Glitch During Power Up
1-μA Maximum Standby Supply Current
Reverse Current Blocking
UL Listed – File No. E169910
CB Certified
Heavy Capacitive Loads
Short-Circuit Protections
DGN PACKAGE
(TOP VIEW)
GND
IN
IN
EN
1
2
3
4
8
7
6
5
OUT
OUT
OUT
OC
DESCRIPTION
The TPS2068 power-distribution switches are intended for applications where heavy capacitive loads and
short-circuits are likely to be encountered. This device incorporates 70-mΩ N-channel MOSFET power switches
for power-distribution systems that require single or dual power switches in a single package. Each switch is
controlled by a logic enable input. Gate drive is provided by an internal charge pump designed to control the
power-switch rise times and fall times to minimize current surges during switching. The charge pump requires no
external components and allows operation from supplies as low as 2.7 V.
When the output load exceeds the current-limit threshold or a short is present, the device limits the output current
to a safe level by switching into a constant-current mode, pulling the overcurrent (OC) logic output low. When
continuous heavy overloads and short-circuits increase the power dissipation in the switch, causing the junction
temperature to rise, a thermal protection circuit shuts off the switch to prevent damage. Recovery from a thermal
shutdown is automatic once the device has cooled sufficiently. Internal circuitry ensures that the switch remains
off until valid input voltage is present. Current limit is typically 2.1 A.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPad is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION (1)
TA
–40°C to 85°C
(1)
(2)
PACKAGE
MSOP – DGN
(2)
ORDERABLE PART NUMBER
Reel of 2500
TPS2068IDGNRQ1
TOP-SIDE MARKING
PSQQ
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
VI
Input voltage range, VI(IN)
–0.3 V to 6 V
Input voltage range, VI(EN)
–0.3 V to 6 V
Voltage range, VI(OC)
–0.3 V to 6 V
VO
Output voltage range, VO(OUT)
IO
Continuous output current , IO(OUT)
Internally limited
Continuous total power dissipation
See Dissipation Rating Table
TJ
Operating virtual-junction temperature range
Tstg
Storage temperature range
–0.3 V to 6 V
–40°C to 105°C
–65°C to150°C
Human-body model (HBM)
ESD
Electrostatic discharge protection
1500 V
Machine model (MM)
50 V
Charged-device model (CDM)
(1)
1000 V
Stresses beyond those listed under absolute maximum ratingsmay cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATING RATING TABLE (1)
(1)
(2)
PACKAGE
TA < 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
DGN-8 (2)
1370 mW
17 mW/°C
600 mW
342 mW
Heatsink the PowerPad™per the recommendations of SLMA002. PCB used for recommendations per appendix A4.
See Recommended Operating Conditions Table for PowerPad connection guidelines to meet qualifying conditions for CB Certificate.
RECOMMENDED OPERATING CONDITIONS (1)
VI
MIN
MAX
Input voltage, VI(IN)
2.7
5.5
V
Input voltage, VI(EN)
0
5.5
V
IO
Continuous output current, IO(OUT)
TJ
Operating virtual-junction temperature
(1)
2
UNIT
0
1.5
A
–40
105
°C
The thermal pad must be connected externally to GND pin to meet qualifying conditions for CB Certificate (DGN package only).
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
ELECTRICAL CHARACTERISTICS
–40°C ≤ TJ ≤ 105° VI(IN) = 5.5 V, IO = 1 A, VI(EN) = 0 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
(1)
MIN
TYP
MAX
UNIT
POWER SWITCH
rDS(on)
Static drain-source on-state resistance,
5-V operation and 3.3-V operation
VI(IN) = 5 V or 3.3 V, IO = 1.5 A
70
150
mΩ
Static drain-source on-state resistance,
2.7-V operation
VI(IN) = 2.7 V, IO = 1.5 A
75
150
mΩ
0.6
1.5
Rise time, output (2)
tr
Fall time, output (2)
tf
VI(IN) = 5.5 V
VI(IN) = 2.7 V
VI(IN) = 5.5 V
CL = 1 μF,
RL = 5 Ω
TJ =25°C
VI(IN) = 2.7 V
0.4
1
0.05
0.5
0.05
0.5
ms
ENABLE INPUT EN
VIH
High-level input voltage
2.7 V < VI(IN) < 5.5 V
VIL
Low-level input voltage
2.7 V < VI(IN) < 5.5 V
2
II
Input current
VI(EN) = 0 V or 5.5 V
ton
Turn-on time (2)
CL = 100 μF, RL = 5 Ω
3
toff
Turn-off time (2)
CL = 100 μF, RL = 5 Ω
10
0.8
-0.5
0.5
V
μA
ms
CURRENT LIMIT
IOS
Short-circuit output current
VI(IN) = 5 V, OUT connected to GND,
Device enabled into short-circuit
1.6
2.1
2.6
A
IOC_TRIP
Overcurrent trip threshold (2)
VI(IN) = 5 V, Current ramp (≤ 100 A/s) on OUT
2.3
2.85
3.4
A
Short-circuit output current (2)
VI(IN) = 5 V, OUT connected to GND, Device enabled into
short-circuit, current measured at VI(IN)
3.2
4.2
5.2
A
IOL
Supply current, low-level output
No load on OUT, VI(EN) = 5.5 V
TJ = 25°C
0.5
1
Over TJ range
0.5
5
IOH
Supply current, high-level output
No load on OUT, VI(EN) = 0 V
TJ = 25°C
43
60
Over TJ range
43
70
Ilkg
Leakage current
OUT connected to ground, VI(EN) = 5.5 V
1
μA
Reverse leakage current
VI(OUT) = 5.5 V, IN = ground
TJ = 25°C
0.2
μA
IOS
(3)
μA
μA
UNDERVOLTAGE LOCKOUT
Low-level input voltage, IN
Hysteresis, IN
2
TJ = 25°C
2.5
75
V
mV
OVERCURRENT OC
VOL(OC)
Output low voltage
IO(OC) = 5 mA
Off-state current
VO(OC) = 5 V or 3.3 V
OC deglitch (2)
OC assertion or deassertion
4
8
0.4
V
1
μA
15
ms
THERMAL SHUTDOWN (4)
Thermal shutdown threshold (2)
135
Recovery from thermal shutdown (2)
125
Hysteresis
(1)
(2)
(3)
(4)
°C
°C
10
°C
Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account
separately.
Specified by design
This configuration has not been tested for UL certification.
The thermal shutdown only reacts under overcurrent conditions.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
3
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
DEVICE INFORMATION
Terminal Functions
NAME
NO.
I/O
EN
4
I
GND
1
DESCRIPTION
Enable input, logic low turns on power switch
Ground
IN
2,3
I
Input voltage
OC
5
O
Overcurrent, open-drain output, active-low
6, 7,8
O
Power-switch output
OUT
Connect to GND (1)
Thermal pad
(1)
See the Recommended Operating Conditions Table for PowerPad connection guidelines to meet qualifying conditions for CB Certificate
(DGN package only).
Functional Block Diagram
(See Note A)
CS
IN
OUT
Charge
Pump
EN
Driver
Current
Limit
OC
UVLO
GND
A.
4
Thermal
Sense
Deglitch
Current sense.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
PARAMETER MEASUREMENT INFORMATION
OUT
RL
tf
tr
CL
VO(OUT)
90%
10%
90%
10%
TEST CIRCUIT
50%
VI(EN)
50%
toff
ton
VO(OUT)
50%
VI(EN)
90%
50%
toff
ton
90%
VO(OUT)
10%
10%
VOLTAGE WAVEFORMS
Figure 1. Test Circuit and Voltage Waveforms
RL = 5 W,
CL = 1 mF,
TA = 25 °C
VI(EN)
5 V/div
VI(EN)
5 V/div
RL = 5 W,
CL = 1 mF,
TA = 25 °C
VO(OUT)
2 V/div
VO(OUT)
2 V/div
t - Time - 400 ms
t - Time - 400 ms
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
5
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
RL = 5 W,
CL = 100 mF,
TA = 25 °C
VI(EN)
5 V/div
VO(OUT)
2 V/div
VI(EN)
5 V/div
RL = 5 W,
CL = 100 mF,
TA = 25 °C
VO(OUT)
2 V/div
t - Time - 400 ms
t - Time - 400 ms
VIN = 5 V,
RL = 3 W,
TA = 255C
VI(EN)
5 V/div
VI(EN)
5 V/div
220 mF
470 mF
100 mF
IO(OUT)
500 mA/div
IO(OUT)
500 mA/div
t − Time − 500 ms/div
t − Time − 500 ms/div
6
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
PARAMETER MEASUREMENT INFORMATION (continued)
VO(OCx)
2 V/div
IO(OUT)
1 A/div
t - Time - 2 ms/div
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
7
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS
TURNON TIME
vs
INPUT VOLTAGE
TURNOFF TIME
vs
INPUT VOLTAGE
1.0
2
CL = 100 mF,
RL = 5 W,
TA = 255C
0.9
0.8
CL = 100 mF,
RL = 5 W,
TA = 255C
1.9
Turnoff Time − mS
Turnon Time − ms
0.7
0.6
0.5
0.4
1.8
1.7
0.3
0.2
1.6
0.1
0
2
3
4
5
VI − Input Voltage − V
1.5
6
2
4
5
VI − Input Voltage − V
Figure 9.
Figure 10.
RISE TIME
vs
INPUT VOLTAGE
FALL TIME
vs
INPUT VOLTAGE
6
0.25
0.6
CL = 1 mF,
RL = 5 W,
TA = 255C
CL = 1 mF,
RL = 5 W,
TA = 255C
0.5
0.2
0.4
Fall Time − ms
Rise Time − ms
3
0.3
0.15
0.1
0.2
0.05
0.1
0
2
3
4
5
VI − Input Voltage − V
6
0
2
Figure 11.
8
3
4
5
VI − Input Voltage − V
6
Figure 12.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
TYPICAL CHARACTERISTICS (continued)
SUPPLY CURRENT, OUTPUT ENABLED
vs
JUNCTION TEMPERATURE
SUPPLY CURRENT, OUTPUT DISABLED
vs
JUNCTION TEMPERATURE
I I (IN) − Supply Current, Output Disabled − µ A
II(IN) - Supply Current, Output Enabled - mA
60
VI = 5.5 V
50
VI = 5 V
40
30
VI = 2.7 V
20
VI = 3.3 V
10
0
-50
0
50
100
0.5
0.45
VI = 5.5 V
VI = 5 V
0.4
0.35
0.3
0.25
0.2
0.15
0.1
0.05
0
−50
150
0
50
100
TJ − Junction Temperature − 5C
TJ - Junction Temperature - °C
Figure 13.
Figure 14.
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
JUNCTION TEMPERATURE
SHORT-CIRCUIT OUTPUT CURRENT
vs
JUNCTION TEMPERATURE
120
2.5
Out1 = 5 V
IOS - Short-Circuit Current Limit - A
100
On-State Resistance − mΩ
150
2.6
IO = 0.5 A
r DS(on) − Static Drain-Source
VI = 3.3 V
VI = 2.7 V
Out1 = 3.3 V
80
Out1 = 2.7 V
60
40
20
2.4
VI = 2.7 V
2.3
VI = 3.3 V
2.2
2.1
VI = 5.5 V
VI = 5 V
2
1.9
1.8
1.7
1.6
0
−50
0
50
100
150
-50
TJ − Junction Temperature − 5C
Figure 15.
0
50
100
150
TJ - Junction Temperature - °C
Figure 16.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
9
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS (continued)
UNDERVOLTAGE LOCKOUT
vs
JUNCTION TEMPERATURE
CURRENT-LIMIT RESPONSE
vs
PEAK CURRENT
2.3
200
VI = 5 V,
TA = 25 °C
2.26
2.22
Current-Limit Response - ms
UVOL − Undervoltage Lockout − V
UVLO Rising
UVLO Falling
2.18
2.14
2.1
−50
0
50
100
150
150
100
50
0
0
TJ − Junction Temperature − 5C
Figure 17.
10
2.5
5
7.5
10
Peak Current - A
Figure 18.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
APPLICATION INFORMATION
Power-Supply Considerations
TPS2060
2
Power Supply
2.7 V to 5.5 V
IN
OUT1
0.1 µF
8
3
5
4
7
Load
0.1 µF
22 µF
0.1 µF
22 µF
OC1
EN1
OUT2
6
OC2
Load
EN2
GND
1
Figure 19. Typical Application
A 0.01-μF to 0.1-μF ceramic bypass capacitor between IN and GND, close to the device, is recommended.
Placing a high-value electrolytic capacitor on the output pin(s) is recommended when the output load is heavy.
This precaution reduces power-supply transients that may cause ringing on the input. Additionally, bypassing the
output with a 0.01-μF to 0.1-μF ceramic capacitor improves the immunity of the device to short-circuit transients.
Overcurrent
A sense FET is employed to check for overcurrent conditions. Unlike current-sense resistors, sense FETs do not
increase the series resistance of the current path. When an overcurrent condition is detected, the device
maintains a constant output current and reduces the output voltage accordingly. Complete shutdown occurs only
if the fault is present long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted before the
device is enabled or before VI(IN) has been applied (see Figure 6). The TPS2068 senses the short and
immediately switches into a constant-current output.
In the second condition, a short or an overload occurs while the device is enabled. At the instant the overload
occurs, high currents may flow for a short period of time before the current-limit circuit can react (see
Figure 8).After the current-limit circuit has tripped (reached the overcurrent trip threshold), the device switches
into constant-current mode.
In the third condition, the load has been gradually increased beyond the recommended operating current. The
current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is
exceeded. The TPS2068 is capable of delivering current up to the current-limit threshold without damaging the
device. Once the threshold has been reached, the device switches into its constant-current mode.
OC Response
The OC open-drain output is asserted (active low) when an overcurrent or overtemperature shutdown condition
is encountered after a 10-ms deglitch timeout. The output remains asserted until the overcurrent or
overtemperature condition is removed. Connecting a heavy capacitive load to an enabled device can cause a
momentary overcurrent condition; however, no false reporting on OC occurs due to the 10-ms deglitch circuit.
The TPS2068 is designed to eliminate false overcurrent reporting. The internal overcurrent deglitch eliminates
the need for external components to remove unwanted pulses. OC is not deglitched when the switch is turned off
due to an overtemperature shutdown.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
11
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
V+
TPS2060
GND
Rpullup
OC1
IN
OUT1
EN1
OUT2
EN2
OC2
Figure 20. Typical Circuit for theOC Pin
Power Dissipation and Junction Temperature
The low on-resistance on the N-channel MOSFET allows the small surface-mount packages to pass large
currents. The thermal resistance of these packages are high compared to those of power packages; it is good
design practice to check power dissipation and junction temperature. Begin by determining the rDS(on) of the
N-channel MOSFET relative to the input voltage and operating temperature. As an initial estimate, use the
highest operating ambient temperature of interest and read rDS(on) from Figure 15. Using this value, the power
dissipation per switch can be calculated by:
PD = rDS(on) × I2
Multiply this number by the number of switches being used. This step renders the total power dissipation from
the N-channel MOSFETs.
Finally, calculate the junction temperature:
TJ = PD × RθJA + TA
Where:
TA= Ambient temperature °C
RθJA = Thermal resistance
PD = Total power dissipation based on number of switches being used.
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,
repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally
sufficient to get a reasonable answer.
Thermal Protection
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for
extended periods of time. The TPS2068 implements a thermal sensing to monitor the operating junction
temperature of the power distribution switch. In an overcurrent or short-circuit condition, the junction temperature
rises due to excessive power dissipation. Once the die temperature rises to approximately 140°C due to
overcurrent conditions, the internal thermal sense circuitry turns the power switch off, thus preventing the power
switch from damage. Hysteresis is built into the thermal sense circuit, and after the device has cooled
approximately10°C, the switch turns back on. The switch continues to cycle in this manner until the load fault or
input power is removed. The OC open-drain output is asserted (active low) when an overtemperature shutdown
or overcurrent occurs.
Undervoltage Lockout (UVLO)
An undervoltage lockout ensures that the power switch is in the off state at power up. Whenever the input
voltage falls below approximately 2 V, the power switch is quickly turned off. This facilitates the design of
hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The
UVLO also keeps the switch from being turned on until the power supply has reached at least 2 V, even if the
switch is enabled. On reinsertion, the power switch is turned on, with a controlled rise time to reduce EMI and
voltage overshoots.
12
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
Universal Serial Bus (USB) Applications
The universal serial bus (USB) interface is a 12-Mb/s, or 1.5-Mb/s, multiplexed serial bus designed for lowto-medium bandwidth PC peripherals (e.g., keyboards, printers, scanners, and mice). The four-wire USB
interface is conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for
differential data, and two lines are provided for 5-V power distribution.
USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power
is distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 V
from the 5-V input or its own internal power supply.
The USB specification defines the following five classes of devices, each differentiated by power-consumption
requirements:
• Hosts/self-powered hubs (SPH)
• Bus-powered hubs (BPH)
• Low-power, bus-powered functions
• High-power, bus-powered functions
• Self-powered functions
SPHs and BPHs distribute data and power to downstream functions. The TPS2068 has higher current capability
than required by one USB port; so, it can be used on the host side and supplies power to multiple downstream
ports or functions.
Host/Self-Powered and Bus-Powered Hubs
Hosts and SPHs have a local power supply that powers the embedded functions and the downstream ports (see
Figure 21). This power supply must provide from 5.25 V to 4.75 V to the board side of the downstream
connection under full-load and no-load conditions. Hosts and SPHs are required to have current-limit protection
and must report overcurrent conditions to the USB controller. Typical SPHs are desktop PCs, monitors, printers,
and stand-alone hubs.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
13
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
Downstream
USB Ports
D+
D−
VBUS
0.1 µF
22 µF
GND
D+
D−
VBUS
0.1 µF
22 µF
GND
Power Supply
3.3 V
5V
IN
OUT1
0.1 µF
D−
7
VBUS
0.1 µF
8
3
USB
Controller
D+
TPS2060
2
5
4
22 µF
GND
OC1
EN1
D+
OC2
EN2
OUT2
D−
6
GND
VBUS
0.1 µF
2 µF
GND
1
D+
D−
VBUS
0.1 µF
22 µF
GND
D+
D−
VBUS
0.1 µF
22 µF
GND
Figure 21. Typical Six-Port USB Host/Self-Powered Hub
BPHs obtain all power from upstream ports and often contain an embedded function. The hubs are required to
power up with less than one unit load. The BPH usually has one embedded function, and power is always
available to the controller of the hub. If the embedded function and hub require more than 100 mA on power up,
the power to the embedded function may need to be kept off until enumeration is completed. This can be
accomplished by removing power or by shutting off the clock to the embedded function. Power switching the
embedded function is not necessary if the aggregate power draw for the function and controller is less than one
unit load. The total current drawn by the bus-powered device is the sum of the current to the controller, the
embedded function, and the downstream ports, and it is limited to 500 mA from an upstream port.
14
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
Low-Power Bus-Powered and High-Power Bus-Powered Functions
Both low-power and high-power bus-powered functions obtain all power from upstream ports; low-power
functions always draw less than 100mA; high-power functions must draw less than 100 mA at power up and can
draw up to 500 mA after enumeration. If the load of the function is more than the parallel combination of 44 Ω
and 10 μF at power up, the device must implement inrush current limiting (see Figure 22). With TPS2068, the
internal functions could draw more than 500 mA, which fits the needs of some applications such as motor driving
circuits.
Power Supply
3.3 V
D+
D−
VBUS
TPS2060
2
10 µF
0.1 µF
IN
OUT1
GND
8
3
USB
Control
5
4
7
0.1 µF
10 µF
Internal
Function
0.1 µF
10 µF
Internal
Function
OC1
EN1
OC2
EN2
OUT2
GND
1
6
Figure 22. High-Power Bus-Powered Function
USB Power-Distribution Requirements
USB can be implemented in several ways, and, regardless of the type of USB device being developed, several
power-distribution features must be implemented.
• Hosts/SPHs must:
– Current-limit downstream ports
– Report overcurrent conditions on USB VBUS
• BPHs must:
– Enable/disable power to downstream ports
– Power up at <100 mA
– Limit inrush current (<44 Ω and 10 μF)
• Functions must:
– Limit inrush currents
– Power up at <100 mA
The feature set of the TPS2068 allows them to meet each of these requirements. The integrated current-limiting
and overcurrent reporting is required by hosts and self-powered hubs. The logic-level enable and controlled rise
times meet the need of both input and output ports on bus-powered hubs, as well as the input ports for
bus-powered functions (see Figure 23).
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
15
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
TUSB2040
Hub Controller
Upstream
Port
SN75240
BUSPWR
A C
B D
GANGED
D+
D−
DP0
DP1
DM0
DM1
Tie to TPS2041 EN Input
D+
A C
B D
GND
OC
5V
IN
DM2
5-V Power
Supply
EN
GND
5V
33 µF†
DM3
A C
B D
1 µF
TPS76333
4.7 µF
SN75240
D+
D−
Ferrite Beads
GND
DP4
IN
3.3 V
4.7 µF
DM4
VCC
5V
TPS2060
GND
PWRON1
GND
OVRCUR1
48-MHz
Crystal
XTAL1
33 µF†
EN1 OUT1
OC1 OUT2
PWRON2
EN2
OVRCUR2
OC2
D+
IN
0.1 µF
Tuning
Circuit
D−
DP3
OUT
0.1 µF
Ferrite Beads
SN75240
DP2
TPS2041B
Downstream
Ports
D−
Ferrite Beads
GND
XTAL2
5V
OCSOFF
33 µF†
GND
D+
Ferrite Beads
D−
GND
5V
†
33 µF†
USB rev 1.1 requires 120 µF per hub.
Figure 23. Hybrid Self / Bus-Powered Hub Implementation
Generic Hot-Plug Applications
In many applications it may be necessary to remove modules or PC boards while the main unit is still operating.
These are considered hot-plug applications. Such implementations require the control of current surges seen by
the main power supply and the card being inserted. The most effective way to control these surges is to limit and
slowly ramp the current and voltage being applied to the card, similar to the way in which a power supply
normally turns on. Due to the controlled rise times and fall times of the TPS2068, these devices can be used to
provide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature of the TPS2068
also ensures that the switch is off after the card has been removed, and that the switch is off during the next
insertion. The UVLO feature insures a soft start with a controlled rise time for every insertion of the card or
module.
16
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
TPS2068-Q1
www.ti.com ................................................................................................................................................................................................ SLVS999 – AUGUST 2009
PC Board
TPS2060
OC1
GND
Power
Supply
2.7 V to 5.5 V
1000 µF
Optimum
0.1 µF
IN
EN1
EN2
Block of
Circuitry
OUT1
OUT2
OC2
Block of
Circuitry
Overcurrent Response
Figure 24. Typical Hot-Plug Implementation
By placing the TPS2068 between the VCC input and the rest of the circuitry, the input power reaches these
devices first after insertion. The typical rise time of the switch is approximately 1 ms, providing a slow voltage
ramp at the output of the device. This implementation controls system surge currents and provides a
hot-plugging mechanism for any device.
DETAILED DESCRIPTION
Power Switch
The power switch is an N-channel MOSFET with a low on-state resistance. Configured as a high-side switch, the
power switch prevents current flow from OUT to IN and IN to OUT when disabled. The power switch supplies a
minimum current of 1.5 A.
Charge Pump
An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate
of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires
little supply current.
Driver
The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associated
electromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and fall
times of the output voltage.
Enable (EN)
The logic enable disables the power switch and the bias for the charge pump, driver, and other circuitry to reduce
the supply current. The supply current is reduced to less than 1 μA when a logic high is present on EN. A logic
zero input on EN restores bias to the drive and control circuits and turns the switch on. The enable input is
compatible with both TTL and CMOS logic levels.
Overcurrent (OC)
The OC open-drain output is asserted (active low) when an overcurrent or overtemperature condition is
encountered. The output remains asserted until the overcurrent or overtemperature condition is removed. A
10-ms deglitch circuit prevents the OC signal from oscillation or false triggering. If an overtemperature shutdown
occurs, the OC is asserted instantaneously.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
17
TPS2068-Q1
SLVS999 – AUGUST 2009 ................................................................................................................................................................................................ www.ti.com
Current Sense
A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently than
conventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitry
sends a control signal to the driver. The driver in turn reduces the gate voltage and drives the power FET into its
saturation region, which switches the output into a constant-current mode and holds the current constant while
varying the voltage on the load.
Thermal Sense
The TPS2068 implements a thermal sensing to monitor the operating temperature of the power distribution
switch. In an overcurrent or short-circuit condition the junction temperature rises. When the die temperature rises
to approximately 140°C due to overcurrent conditions, the internal thermal sense circuitry turns off the switch,
thus preventing the device from damage. Hysteresis is built into the thermal sense, and after the device has
cooled approximately 10 degrees, the switch turns back on. The switch continues to cycle off and on until the
fault is removed. The open-drain false reporting output (OC) is asserted (active low) when an overtemperature
shutdown or overcurrent occurs.
Undervoltage Lockout
A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a control
signal turns off the power switch.
18
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2068-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
9-Nov-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
TPS2068IDGNRQ1
ACTIVE
MSOPPower
PAD
DGN
Pins Package Eco Plan (2)
Qty
8
2500 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
CU NIPDAU
MSL Peak Temp (3)
Level-2-260C-1 YEAR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS2068-Q1 :
• Catalog: TPS2068
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jul-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TPS2068IDGNRQ1
Package Package Pins
Type Drawing
MSOPPower
PAD
DGN
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
5.3
B0
(mm)
K0
(mm)
P1
(mm)
3.3
1.3
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jul-2010
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS2068IDGNRQ1
MSOP-PowerPAD
DGN
8
2500
370.0
355.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated