Frontier Electronics Corp. 667 E. COCHRAN STREET, SIMI VALLEY, CA 93065 TEL: (805) 522-9998 FAX: (805) 522-9989 E-mail: [email protected] Web: http://www.frontierusa.com 1A SURFACE MOUNT SUPER FAST RECOVERY RECTIFIERS SFS1A THRU SFS1J SOLDERING PAD FEATURES z FOR SURFACE MOUNTED APPLICATIONS z LOW PROFILE PACKAGE z BUILT-IN STRAIN RELIEF z EASY PICK AND PLACE z PLASTIC MATERIAL USED CARRIES UNDERWRITERS LABORATORY CLASSIFICATION 94 V-0 z SUPER FAST SWITCHING z GLASS PASSIVATED CHIP JUNCTION z HIGH TEMPERATURE SOLDERING:250°C /10 SECONDS AT TERMINALS MECHANICAL DATA z CASE: MOLDED PLASTIC, DO-214AC (SMA), DIMENSIONS IN INCHES AND (MILLIMETERS) z TERMINALS: SOLDER PLATED z POLARITY: INDICATED BY CATHODE BAND z WEIGHT: 0.064 GRAMS CATHODE .087(2.2) .065(1.65) .040(1.25) .071(1.8) .177(4.5) .220(5.6) .192(4.9) .110(2.8) .090(2.3) .190(4.8) .157(4.0) .100(2.6) .080(2.0) .071(1.8) .035(0.9) .080(2.0) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS RATINGS AT 25°C AMBIENT TEMPERATURE UNLESS OTHERWISE SPECIFIED SINGLE PHASE, HALF WAVE, 60 HZ, RESISTIVE OR INDUCTIVE LOAD. FOR CAPACITIVE LOAD, DERATE CURRENT BY 20% RATINGS MAXIMUM RECURRENT PEAK REVERSE VOLTAGE MAXIMUM RMS VOLTAGE MAXIMUM DC BLOCKING VOLTAGE MAXIMUM AVERAGE FORWARD RECTIFIED CURRENT AT TL=90°C MAXIMUM OVERLOAD SURGE 8.3ms SINGLE HALF SINE-WAVE TYPICAL JUNCTION CAPACITANCE (NOTE 1) TYPICAL THERMAL RESISTANCE (NOTE 2) STORAGE TEMPERATURE RANGE OPERATING TEMPERATURE RANGE SYMBOL SFS1A VRRM VRMS VDC 50 35 50 SFS1B SFS1D SFS1E SFS1G SFS1H SFS1J UNITS 100 70 100 200 140 200 300 210 300 400 280 400 500 350 500 600 420 600 V V V IO 1.0 A IFSM 30 A CJ θJL TSTG TOP 15 10 PF °C /W °C °C 30 -55 TO + 150 -55 TO + 125 ELECTRICAL CHARACTERISTICS (AT TA =25°C UNLESS OTHERWISE NOTED) CHARACTERISTICS SYMBOL SFS1A MAXIMUM FORWARD VOLTAGE AT 1.0A AND 25℃ VF MAXIMUM REVERSE CURRENT AT 25℃ IR SFS1B SFS1D SFS1E 0.95 SFS1H 1.25 SFS1J 1.85 UNITS V μA 10 MAXIMUM REVERSE RECOVERY TIME (NOTE 3) TRR 35 MARKING SF1A SF1B SF1D SF1E NOTE: 1. MEASURED AT 1.0 MHZ AND APPLIED REVERSE VOLTAGE OF 4.0 V 2. THERMAL RESISTANCE FROM JUNCTION TO TERMINAL 5.0mm2 (.013 mm THICK) LAND AREAS 3. REVERSE RECOVERY TEST CONDITIONS: IF=0.5A, IR=1.0A, IRR=0.25A SFS1A THRU SFS1J SFS1G nS SF1G SF1H SF1J Page: 1 RATINGS AND CHARACTERISTIC CURVE SFS1A THRU SFS1J FIG. 1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 100Ω NO INDUCTIVE FIG. 2-TYPICAL FORWARD Trr 2.0 +0.5A PULSE GENERATOR ( NOTE 2 ) (+) 25 Vdc (approx) (-) 0 1Ω NON INDUCTIVE OSCILLOSCOPE (+) -0.25A ( NOTE 1 ) NOTE: 1. RISE TIME=7ns MAX. INPUT IMPEDANCE=1 MOhms 22PF 2. RISE TIME =10ns MAX. SOURCE IMPEDANCE=50 OHMS 25 50 75 100 125 150 175 LEAD TEMPERATURE (oC) FIG. 4-TYPICAL INSTANTANEOUS INSTANTANEOUS FORWARD CURRENT (A) TJ=100oC 10 o TJ=80 C 1.0 TJ=25oC 0.1 0.01 FORWARD CHARACTERISTICS 100 120 140 SFS1A~SFS1D 1.0 SFS1E~SFS1G .1 .01 SFS1J .001 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE (V) PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG. 6-TYPICAL JUNCTION CAPACITANCE FIG. 5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 200 40 8.3 ms Single Half Sine Wave (JEDEC Method) 30 100 JUNCTION CAPACITANCE (pF) PEAK FORWARD SURGE CURRENT (A) INSTANTANEOUS REVERSE CURRENT (uA) 0 FOR 10/20 ns/cm 10 40 60 80 Single Phase Half Wave 60 Hz Resistive or Inductive Load SET TIME BASE 100 20 P.C.B MOUNTED ON 0.3×0.3”(8.0×8.0mm) COPPER PAD AREAS 1.0 1cm FIG. 3-TYPICAL REVERSE CHARACTERISTICS 0 CURRENT (A) (-) D.U.T. CURRENT DERATING CURVE AVERAGE FORWARD 50Ω NO INDUCTIVE 25 20 15 10 5 0 1 5 10 20 50 NUMBER OF CYCLES AT 60 Hz 100 40 TJ=25oC SFS1A~SFS1D 20 10 6 4 SFS1E~SFS1J 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE (V) SFS1A THRU SFS1J Page: 2