6,20 MAXIMUM CONDITION 17,16 BY T. 10 mA22 OUTPUT VOLTAGE (OPERATED) (ON) 0.2 0. VOLTS V OUTPUT LEAKAGE CURRENT 2 (RELEASED) (OFF) 0.2 10 A #0,15 . 25 $ C +0,40 -0,20 DRAWING NUMBER 8 ISSUE CHECK 4 S 1 S 2 S 1 S 10% TO 90% 90% TO 10%# VOLTAGE EXTERNALLY APPLIED TO OUTPUT +40 VDC MAX IN "OFF" CO -0.8 VDC M IN "ON" O LOAD ON OUTPUT 40 mA TEMPERATURE -40 TRANSIENT SUPPLY VOLTAGE +80V FOR 25 TRANSIENT SUPPLY CURRENT -.5 A TO + FOR 15 SEC .5 A MAX TRANSIENT OUTPUT CURRENT -.5 A TO + FOR 15 SEC .5 A MAX 6,50 #0,05 9 8 6 #1 0,10 MAX 6 WITH SWITCH NDITION ONLY IN WITH SWITCH R "OFF" CONDITION 5 MI N, MAX $C TO +160 $C 2 HR MAX 0 mSEC MAX Vs (+) (RED) OUTPUT (0) (GREEN) 4,85 #0,10 LEFT RELEASE C Bo RS 12,00 4,5 #0,1 9,49 12 VDC 25 $C 12V, 25 C$ 4.5V, -40 12V, 25 C$ 24V, -40 #0,01 10,48 SAV LEFT OR RIGHT OPERATING RANGE TO $C TO $C 12V, 25 C$ TO 4.5V, 150 $C 12V, 25 C$ TO 24V, 150 $C 11 7,1 #0,2 #0,02 MIN OPERATE RELEASE DIFF. 1,19 -1,04 0,38 #0,30 #0,33 #0,33 -0,03 0,03 #0,25 #0,20 4 12 DIFFERENTIAL L TO R, R TO L 2,21 #0,64 0,03 #0,25 -0,03 #0,15 0,03 #0,46 -0,03 #0,48 -0,03 #0,23 -0,03 #0,53 0,03 #0,51 -0,03 #0,51 -0,03 #0,53 ELECTROSTATIC SENSITIVE DEVICES 2 : 1 SCALE DO NOT OPEN OR HANDLE EXCEPT AT A STATIC FREE WORKSTATION DO NOT SCALE PRINT TOLERANCES APPLY TO DESIGN UNITS. CONVERSIONS A THIS DRAWING COVERS A PROPRIETARY ITEM HONEYWELL. THIS DRAWING IS NOT TO BE C AND IS THE PROPERTY OF MICRO SWITCH. OPIED OR USED WITHOUT THE APPROVAL OF BLACK 13 A DIVISION OF MICRO SWITCH. CATALOG LISTING Honeywell Division FED. MFG. CODE 91929 SOLID STATE VANE SWITCH 2AV54 RE ONLY FOR REFERENCE. UNLESS NOTED, TOLERANCE DIM. ANSI Y14.5M-1982 APPLIES 3 THIRD ANGLE PROJECTION 4 RED 13 1 0,05 #0,18 ESD SENSITIVITY: CLASS 3 GREEN 13 G OUTPUT MECHANICAL CHARACTERISTICS 22,55 #0,15 134 #3 MIN GROUND (-) (BLACK) BLOCK DIAGRAM SHOWING CURRENT SINKIN 5 17,78 TRIGGER CIRCUIT AND AMPLIFIER 10 LEFT OPERATE D RIGHT RELEASE B 11JUN10 2X R 5,00 CHECK 3 FEB 00 6.2 0.2 -40 TO +30 CHECK 3 FEB 00 TSM DRAWN 40 mA LOAD VOLTAGE REGULATOR 16,60 2D OUTPUT TRANSISTOR LEAKAGE A SUPPLY VOLTAGE (Vs) 8 PRS 11JUN10 PTC/CAD 20 mA MAX LOAD 14,85 RIGHT OPERATE A 0066220 4 OLTS +0,0 -0,1 -A- TSM 3 FEB 00 CURRENT ABSOLUTE MAXIMUM RATINGS Bo. HALL SENSOR CO95751 PLUS LOAD mA INE 3,5 2,30 1 CURRENT SINK MAX REMARKS $C SUPPLY CURRENT OUTPUT SWITCHING 7 TIME RISE TIME (REL. POINT) FALL TIME (OPER. POINT) UTE, 30 $ PAGE 1 OF 1 PR-18516 MINIMUM CONDITION REVISIONS B TYP 25 ICS. 2,80 RELEASE NO. 2AV54 4,57 2AV54 C$ ELECTRICAL CHARACTERISTICS 16,27 5,30 #0,05 CENTER A C$ TO +150 #0,10 REPLACES X92982-AV NOTES 1 OVER VOLTAGE RANGE OF 4.5 TO 24 VDC AND TEMPERATURE RANGE OF -40 2 SWITCH IS OFF (RELEASED) WHEN VA NE IS IN GAP 3 CHARACTERISTICS MEASURED WITH TH E VANE AT NOMINAL DIMENSION AND A 20mA LOAD 4 A 0,79 #0,01 THICK CRS (ANNEALED 1010-1018 O R LOWER CARBON) VANE OF SHOWN DIMENSIONS IS TO BE USED W HEN CHECKING MECHANICAL CHARACTERIST VANE CENTER TO BE HELD 5,30 # 0,05 FROM RIVET CENTERLINE 5 Bo = (MECHANICAL CHARACTERISTICS CENTER REFERENCE POINT), DETERMINED THE EQUATION: (A+B+C+D)/4=Bo. OPERATE = TRAILING EDGE TRIGGER POIN RELEASE = LEADING EDGE TRIGGER P OINT. DIFFERENTIAL = OPERATE MINUS RELEASE (A - C) 6 ABSOLUTE MAXIMUM RATINGS ARE THE EXTREME LIMITS THE DEVICE WILL WITHSTAND WITHOUT PERMANENT DAMA GE TO THE DEVICE. HOWEVER, DEVICE OPERATION IS NOT GUARANTEED AS M AXIMUM LIMITS ARE APPROACHED 7 MAX RISE TIME IS BASED ON 4700 p F +20% -10% CAPACITOR FROM OUTPUT TO COMMON (GROUND) 8 THIS DIMENSION TO BE MEASURED FR OM BASE OF IC TOWER TO MAGNET FACE. STEADY STATE DEFLECTION AT TOP O F IC TOWER MAY NOT EXCEED 0,10 ABSOL RELATIVE TO DATUM A 9 THIS DIMENSION TO BE MEASURED FR OM BASE OF IC TOWER TO RIVET CENTERL 10 EPOXY IN THIS AREA MAX. 0,3 HEIG HT PERMISSIBLE 11 CATALOG LISTING AND DATE CODE MA RKED THIS SURFACE 12 A POSITIVE DELTA OPERATE MEANS T HE OPERATE POINT IS MOVING AWAY FROM A POSITIVE DELTA RELEASE MEANS T HE RELEASE POINT IS MOVING TOWARD Bo DELTAS ARE REFERENCED FROM CHARA CTERISTIC MEASUREMENT AT 12 VDC AND 13- WIRES ARE 24 AWG CROSS-LINKED PO LYETHYLENE mm NO PLACES ONE PLACE TWO PLACES THREE PLACES ANGLES X X,X X,XX TOL mm/in 1/.04 0.4/.01 6 0.15/.0 06 SI METRIC DESIGN UNITS WEIGHT S ARE + - DIM. TOL in mm/in X.X X.XX X.XXX 0.8/.03 0.38/.015 0.13/.005 US CUSTOMARY