TI THMC45

SLIS101A − MAY 2001
D 5-V DC Fan Motor PWM Drive for Speed
D
D
D
D
D
Control With No External Power Drive
Stage Required
High Efficiency H-Bridge Topology With
Integrated Low RDSON MOS Output Drivers
to Drive Single Winding, Bipolar Wound,
Two-Phase BLMs
Digital PWM Input to Control Output PWM
Frequency and Duty Cycle—Suited for
Cooling Fan Applications Requiring
Variable RPM Control to Reduce
Noise/Increase MTBF
Single Wire RPM Control, Tachometer
Feedback Signal, and Locked Rotor Detect
Feedback Signal
Low Current Sleep State
Tachometer Signal Valid Over Entire RPM
Range
D Noise Immune Signal Conditioning to Allow
D
D
D
Use of Low Cost Hall Effect Position
Sensor
Locked Rotor Protection With Auto Retry
Thermal Shutdown Protection
8-Pin MSOP PowerPad Package Suited
for Small Fan Circuit Board and Rotor
Housing
DGN Package
(TOP VIEW)
VPWR
OUTA
OUTB
GND
1
8
2
7
3
6
4
5
PWM
H−
H+
TACH
description
The THMC45 is a dc brushless motor (BLM) driver and control device designed for use with low-voltage (5 V
or 3.3 V) dc cooling fans having two-phase motors with a single-winding stator. The device includes a
high-efficiency H-bridge pulse width modulation (PWM) drive topology with integrated MOS high-side and
low-side drivers, plus a PWM control input stage to provide the industry’s first efficient speed control solution
inside low-voltage dc cooling fans. This solution eliminates the need for any power drive components on the
main system board, reducing printed-circuit board (PCB) component count, PCB space, and assembly time.
The device also offers two advantages over the other commonly used fan speed control methods, adjustable
external dc supply voltage and adjustable external PWM drive duty cycle.
Unlike the external linear voltage regulation method, the THMC45 high-efficiency PWM drive method adjusts
the level of motor winding power while all other circuitry inside the fan obtains a fixed dc voltage from the fan
supply. This eliminates problems with loss of headroom to internal control circuitry at low fan supply voltage and
the resulting limitation of low-speed operation of 40% that is typically associated with external dc voltage
regulation. The high-efficiency PWM drive method employed by the THMC45 reduces fan supply power
consumption and maximizes full-scale RPM speed over the external linear voltage regulation method, which
has V × I power loss due to the voltage drop across the regulator.
The THMC45 includes a Hall sensor amplifier and signal conditioning, global thermal shutdown, and locked
rotor protection with automatic restart after a locked rotor condition. The device provides a sleep state to
eliminate the need for an external power component to disconnect the fan from the supply during a system sleep
state. The device also has internal reverse blocking capability to prevent excessive reverse leakage current due
to reversal of power line. The THMC45 is primarily designed for 5-V dc notebook PC cooling fan applications
that require single-wire RPM speed control and tachometer feedback. However, with an open-drain tachometer
output, the device is also suitable for applications that require two wires for RPM speed control and tachometer
signal.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
Copyright  2001, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&
*%$"# $ " #'&$$!"# '& "+& "&# &,!# #"%&"#
#"!*!* -!!". *%$" '$&##/ *&# " &$&##!). $)%*&
"&#"/ !)) '!!&"&#
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SLIS101A − MAY 2001
functional block diagram
VPWR
Sleep State
Detection
SLEEP
OSC
Oscillator
70 kΩ
PWM
8
SLEEP
OSC
Locked Rotor
Detection and
Auto-Restart
+5 V
OSC
1
VPWR
C1
1 µF
OSC
ITACH/RD
Signaling
H-Bridge
Drive
and
Control
2
OUTA
ITACH
700 µA
S N
N S
+5 V
Hall
Sensor
H−
7
H+
6
TACH
5
−
+
OUTB
4
GND
Signal
Conditioning
Hall
Sensor
Amplifier
TACH
TACH
2
3
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLIS101A − MAY 2001
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
GND
4
I
Ground
H+
6
I
Hall sensor positive input
H−
7
I
Hall sensor negative input
OUTA
2
O
Motor winding drive output A
OUTB
3
O
Motor winding drive output B
PWM
8
I/O
PWM duty cycle control input and tachometer/locked rotor detect current sink output
TACH
5
O
Open drain tachometer output signal
VPWR
1
I
5-V Supply voltage input
absolute maximum ratings over operating case temperature range (unless otherwise noted)†
Supply voltage input, VPWR (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Open-drain tachometer output voltage, VTACH (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
H-bridge output voltage, VOUTA, VOUTB (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Hall sensor amplifier input voltage, VH+, VH− (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Speed control voltage input and tachometer/locked rotor feedback, VPWM (see Note 1) . . . . . . . . . . . . . . 6 V
Continuous H-bridge output current source/sink, IOUTA, IOUTB (see Note 2) . . . . . . . . . . . . . . . . . . . . 350 mA
Continuous H-bridge output current source/sink, IOUTA, IOUTB (see Note 3) . . . . . . . . . . . . . . . . . . . . 260 mA
Continuous power dissipation, PD (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 W
Operating case temperature range, TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −30°C to 80°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature (soldering, 10 sec), TLEAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values are with respect to GND.
2. Assumed package plus PCB system thermal impedance = 170°C/W, TA = 25°C.
3. Assumed package plus PCB system thermal impedance = 170°C/W, TA = 80°C.
4. In free air at TA = 25°C, assumed 58.4°C/W and TJ = 150°C.
recommended operating conditions
Supply voltage, VPWR
PWM high-level input voltage, VIH
MIN
MAX
2.5
5
2
PWM low-level input voltage, VIL
PWM input frequency, fPWM
Operating case temperature, TC
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
V
V
0.8
V
18
50
kHz
−30
80
°C
3
SLIS101A − MAY 2001
dc electrical characteristics, VPWR = 5V, TA = −30°C to 80°C (unless otherwise noted)
supply current
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
5
5.5
Supply voltage normal operation
4.5
VPWR
Supply voltage functional with derated
performance
2.4
VPOR
Power-on reset voltage threshold
Increase VPWR until logic active
1.5
IVPWR
VPWR supply current
IL = 0 A
Idle condition, in locked rotor detect
0.5
1.5
0.5
1.5
IREV
Reverse leakage
ISLEEP
Sleep-state current
VPWR = −5 V at TA = 25°C
VPWM = 0 V for >2 ms
4.5
UNIT
V
V
5
mA
mA
75
300
µA
TYP
MAX
UNIT
Hall sensor signal conditioning
PARAMETER
IIB(HL)
VICR(HL)
TEST CONDITIONS
Input bias current
See Note 5
MIN
−1
ICR(HL) common mode input voltage range
VIO
Hall amplifier input offset voltage
NOTE 5: Design target only. Not tested in production.
1
1
µA
3.5
V
−20
0
20
mV
MIN
TYP
MAX
OUTA, OUTB phase winding driver outputs
PARAMETER
TEST CONDITIONS
ILEAK
OUTA, OUTB output leakage current
VPWM = 0 V for >2 ms,
VOUTx = 5 V
RDSON(Low)
OUTA, OUTB low-side output ON
resistance
IOUTx = 200 mA,
TA = 25°C
RDSON(High)
OUTA, OUTB high-side output ON
resistance
IOUTx = −200 mA,
TA = 25°C
OUTA, OUTB low-side output ON
resistance
IOUTx = 100 mA,
TA = 25°C,
IOUTx = −100 mA,
TA = 25°C,
RDSON
OUTA, OUTB high-side output ON
resistance
sleep state,
UNIT
1
µA
1.6
2.5
Ω
1.9
2.5
Ω
VPWR = 2.4 V
3
6
Ω
VPWR = 2.4 V
3.5
6
Ω
TYP
MAX
−1
PWM input/TACH pulse output
PARAMETER
TEST CONDITIONS
VIH
VIL
PWM high-level input voltage
IIH
IIL
PWM high-level input current
PWM low-level input current
VPWM = 5 V
VPWM = 0 V
VOL
PWM input tachometer pulse output low voltage
IPWM = 2 mA
MIN
2
UNIT
V
PWM low-level input voltage
−1
75
0.8
V
1
µA
200
µA
0.4
V
TACH open-drain output
PARAMETER
IIH
VOL
4
TEST CONDITIONS
VTACH = VPWR
ITACH = 5 mA
TACH output high leakage
TACH output low voltage
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
−1
TYP
MAX
UNIT
1
µA
400
mV
SLIS101A − MAY 2001
ac electrical characteristics, VPWR = 5 V, TA = −30°C to 80°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
18
30
50
UNIT
fPWM
PWM input frequency
t(SLEEP)
Time to enter sleep state after no transitions on PWM
terminal
See Figure 5
2
ms
t(PW)
td
Tachometer signal pulse width
See Figure 4
1
µs
Delay after rising edge of PWM input for TACH signal
See Figure 4
1
µs
tRD
tRETRY
Locked rotor detect delay time
See Figure 6
1
s
Auto-restart delay time
See Figure 6
8
s
t(de-glitch)
Hall transition valid time for commutation to occur
See Figures 1 and 4
25
µs
t(PWM_de-glitch)
De-glitch time for PWM input to prevent TACH current
pulses from falsely triggering PWM
See Figure 5
25
µs
OUTA, OUTB output fall time
See Note 5
200
ns
OUTA, OUTB output rise time
See Note 5
200
ns
TEST CONDITIONS
MIN
tf(OUT)
tr(OUT)
kHz
NOTE 5: Design target only. Not tested in production.
thermal resistance
PARAMETER
RθJ(SYS)
Thermal resistance, in system
2 oz. copper traces, JEDEC low K board, 0 LFPM airflow
RθJC
Thermal resistance, junction-to-case
Exposed back-side die mount
MAX
UNIT
58.4
°C/W
4.7
°C/W
PRINCIPLES OF OPERATION
general overview
The THMC45 is a dc BLM driver and control device designed for use with low-voltage (5 V or 3.3 V) dc cooling
fans having two-phase motors with a single winding, bipolar-wound stator. The device is intended primarily for
low-voltage cooling fan applications requiring speed control with a tachometer feedback signal to ensure normal
fan operation. The output drive PWM duty cycle and frequency are dependent on the input signal on the PWM
terminal. The device has an internal Hall sensor amplifier and signal conditioning with drive commutation logic,
a low power sleep-state mode, and locked rotor protection with automatic restart after a locked rotor condition.
The PWM terminal is used to input PWM frequency and duty cycle, to output a tachometer current pulse
feedback signal, and to provide a means for entering sleep and run states. The THMC45 provides a more
effective drive solution to fan RPM control than either external linear voltage regulation or external PWM drive.
The device is offered in an MSOP-8 miniature surface-mount package to meet the critical space constraints of
PCB designs of small low-voltage fans typically found in notebook PCs.
supply voltage input (VPWR)
The VPWR terminal serves as the voltage supply input to the THMC45. A 0.1-µF bypass capacitor should be
placed as close to this terminal as layout permits.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SLIS101A − MAY 2001
PRINCIPLES OF OPERATION
Hall sensor amplifier inputs (H+, H−)
The THMC45 has an internal Hall sensor amplifier with signal conditioning to allow the use of low-cost Hall
sensors requiring no external components for noise filtering. The Hall signal conditioning block receives a
low-level differential voltage from the Hall position sensor and implements a zero differential voltage crossing
detection with a de-glitch time of 25 µs (typical), t(de-glitch), to reject noise on the Hall signal inputs. Refer to
Figure 1, the OUTA output changes from sourcing current to sinking current after the 25-µs de-glitch time.
Likewise, the OUTB output changes from sinking current to sourcing current after the 25-µs de-glitch time. The
Hall amplifier circuit has an input offset voltage, VIO, not greater than ±13 mV when VPWR is between 4.5 V and
5.5 V. The common mode input voltage range is 1 V to 3.5 V when VPWR is between 4.5 V and 5.5 V.
Differential Hall
Signal (H+ − H−)
t(de-glitch)
t(de-glitch)
t(de-glitch)
Conditioned Hall
Amplifier Output
(Internal)
PWM Input
OUTA
OUTB
Figure 1. Hall Sensor Signal Conditioning Waveform and OUTA/OUTB Commutation
Illustrated in truth table format, Table 1 shows OUTA and OUTB commutation and PWM.
Table 1. OUTA and OUTB Low-Side Drive Commutation
H+
H−
OUTA
OUTB
H
L
H
PWM
L
H
PWM
H
H-bridge motor drive outputs (OUTA, OUTB)
Using an H-bridge to drive a bipolar wound, two-phase BLM provides several advantages for dc fans over the
unipolar-wound motor commonly driven by two commutated low-side switches. A bipolar-wound motor has only
two connections; hence, the H-bridge drive topology requires only two output terminals and two traces are
needed on the fan PCB. A bipolar-wound stator has a single-wire winding which is simpler to manufacture, and
thus increases reliability and reduces manufacturing time. All factors combine to allow a smaller diameter fan
center hub, and thus higher blade area for increased airflow on a given fan frame size. Generally, an H-bridge
drive method with bipolar-wound stator increases fan motor torque density over a typical unipolar drive method.
The H-bridge drive method also eliminates the need for snubbing inductive energy at commutation transitions
and allows for recirculation of winding current to maintain energy in the motor while PWM switching occurs.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLIS101A − MAY 2001
PRINCIPLES OF OPERATION
H-bridge motor drive outputs (OUTA, OUTB) (continued)
Figures 2a and 2b show THMC45 H-bridge motor drive states with stator winding current being driven from
OUTA to OUTB and from OUTB to OUTA, respectively, based on the Hall sensor commutation state. As shown
during tON, PWM signal is high and the drive current is from VPWR through the activated switches and motor
to GND. PWM occurs on the low side, and the stator winding inductive current recirculates on the high side
during tOFF and PWM signal is low (see Figure 3 for motor current waveform). Recirculation of inductive current
through the high-side switches during tOFF, known as synchronous rectification, improves power conversion
efficiency by maintaining energy in the stator winding and results in a continuous dc current level.
VPWR
ON
M1
PWM tON
OUTA
VPWR
PWM
M2
ON
M1
I(RECIRCULATE) M2
OUTB
Motor
Motor
OUTA
OFF
M3
PWM
I(DRIVE)
PWM
M4
OFF
OUTB
M3
GND
PWM tOFF
M4
PWM
GND
H+
H−
OUTA
OUTB
H
L
H
PWM
a) A to B Current Direction
VPWR
PWM
M1
PWM tON
OUTA
VPWR
M2
ON
PWM
M1
I(RECIRCULATE) M2
OUTB
Motor
Motor
OUTA
PWM
M3
ON
I(DRIVE)
OFF
M4
PWM
M3
GND
OUTB
PWM tOFF
M4
OFF
GND
H+
H−
OUTA
OUTB
L
H
PWM
H
b) B to A Current Direction
Figure 2. H-Bridge PWM Drive With Synchronous Rectification
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SLIS101A − MAY 2001
PRINCIPLES OF OPERATION
PWM input (PWM)
The PWM input provides several functions:
D Input for controlling H-bridge PWM drive frequency and duty cycle
D Output for a tachometer current sink pulse on the first rising edge of the PWM input signal after a
commutation
D Initiating a low-current sleep state when the voltage maintained a logic low level for 2 ms (typical) or longer,
and allowing the THMC45 to return to a normal run state on the next rising edge of the PWM input signal
The THMC45 requires a TTL level PWM input signal from another device, such as a Super I/O device. This
signal, along with the Hall sensor input, is used to PWM the OUTA and OUTB outputs according to truth table,
Table 1.
It is recommended that the frequency of the PWM input signal be between 18 kHz and 60 kHz. A PWM frequency
of 18 kHz or higher, being above the audible range, ensures quiet fan operation. Frequencies above 18 kHz
also promote efficient fan speed control by keeping the PWM period below the electrical L/R time constant of
the motor. This allows continuous current in the fan windings (see Figure 3). Keeping the PWM frequency below
60 kHz minimizes switching losses. Switching losses, typically observed at higher frequencies, decreases
overall efficiency.
The speed of the cooling fan can be varied by adjusting the duty cycle of the PWM input signal. The higher the
duty cycle of the PWM input signal, the higher the current in the fan windings, and thus results in faster fan speed.
I(DRIVE)
I(MOTOR)
I(RECIRCULATE)
PWM Period
tOFF
tON
PWM
Figure 3. Motor Current Waveform
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLIS101A − MAY 2001
PRINCIPLES OF OPERATION
tachometer signaling on PWM input (PWM)
The PWM terminal of the THMC45 provides a 1-µs (typical) current sink pulse, t(PW), following the next rising
edge of the PWM input signal after the Hall sensor amplifier changes states (see Figure 4). Note that the
THMC45 incorporates a blanking circuit that disregards transitions on the PWM terminal during the TACH
current pulses. This ensures that the TACH pulses do not corrupt the output PWM signal. This current signal
can be detected with external circuitry and can be sent to the TACH input of the hardware monitor portion of
a Super I/O device.
Differential Hall
Signal (H+ − H−)
t(de-glitch)
t(de-glitch)
t(de-glitch)
Conditioned Hall
Amplifier Output
(Internal)
PWM Input
td
t(PW)
TACH Current
Sink Pulses
TACH
Figure 4. Tachometer Current Pulse Timing on PWM Input Pin
sleep/run states using PWM input (PWM)
The THMC45 enters a low-current sleep state when the PWM input maintains a logic low level for more than
2 ms (typical), t(SLEEP). In sleep state, the OUTA and OUTB outputs are in a high-impedance state. The THMC45
transitions from sleep state to run state on the first rising edge on the PWM input. Figure 5 shows the timing
relationships between the PWM signal and sleep/run state.
PWM Input
t(SLEEP)
t(PWM_de-glitch)
OUTA, OUTB
Enable Signal
Figure 5. PWM Input Signal, Sleep State, and Run State Timing
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SLIS101A − MAY 2001
PRINCIPLES OF OPERATION
locked rotor protection
An internal digital timer is used to monitor the output of the Hall sensor amplifier. When change in commutation
state is not observed via the Hall amplifier inputs within 1 second (typical), t(RD), the OUTA and OUTB outputs
are disabled for 8 seconds (typical), t(RETRY). After this period, the THMC45 re-enables the OUTA and OUTB
outputs to automatically restart the motor after a locked rotor condition. When the locked rotor condition
continues to exist, the above process repeats itself until the locked condition is removed or the THMC45 is
powered down (see Figure 6).
Conditioned Hall
Amplifier Output
(Internal)
t(RD)
t(RD)
t(RETRY)
t(RETRY)
OUTA, OUTB
Enable
Figure 6. Typical Locked Rotor Protection Timing Waveforms
open-drain tachometer output (TACH)
The TACH output is an open-drain output that is activated by the output of the Hall sensor comparator output.
When the output of the Hall sensor comparator is high, the TACH output floats high. When the output of the Hall
sensor amplifier is low, the TACH output is pulled low. The resulting output signal has two pulses per revolution
on a four-pole motor.
The TACH output can be used to monitor and measure actual fan speed. It may also be used as part of a
closed-loop speed control system.
thermal shutdown
The THMC45 provides protection against excessive device temperature with a thermal sensor to monitor the
die temperature. In the event that operating or abnormal condition causes the die temperature to exceed t(SD),
the thermal shutdown threshold (175°C typical), all output drivers are turned off. When t(SD) has been exceeded,
the die temperature must fall below a hystersis temperature, t(SD_HYS) (15°C typical) before the output drivers
are re-enabled.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLIS101A − MAY 2001
THERMAL INFORMATION
POWER DISSIPATION
vs
AMBIENT TEMPERATURE
1.3
P D − Power Dissipation − W
1.2
1.1
RθJ(SYS) = 100°C/W
1.0
RθJ(SYS) = 125°C/W
0.9
0.8
RθJ(SYS) = 170°C/W
0.7
0.6
RθJ(SYS) = 225°C/W
0.5
0.4
0.3
0.2
RθJ(SYS) = 285°C/W
0.1
0.0
20
30
40
50
60
70
80
90
100
110
120
130
140
150
t − Ambient Temperature − °C
Note: RθJ(SYS) refers to composite thermal impedance provided by the IC package, PCB, and fan housing.
Figure 7
CONTINUOUS CURRENT
vs
AMBIENT TEMPERATURE
I VPWR − Continuous Current − A
0.5
RθJ(SYS) = 100°C/W
0.4
0.3
RθJ(SYS) = 125°C/W
0.2
RθJ(SYS) = 170°C/W
RθJ(SYS) = 225°C/W
0.1
RθJ(SYS) = 285°C/W
0.0
20
30
40
50
60
70
80
90
100
110
120
130
140
150
t − Ambient Temperature − °C
Note: RθJ(SYS) refers to composite thermal impedance provided by the IC package, PCB, and fan housing.
Analysis assumes combined high and low-side RDSon = 5.5 Ω.
Figure 8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SLIS101A − MAY 2001
APPLICATION INFORMATION
GND
PWM
INPUT
+ 5V
TACH
R1
1.3 kΩ
1
C1
1 µF
10 V
2
+
3
4
VPWR
PWM
H−
OUTA
THMC45
H+
OUTB
TACH
GND
8
7
6
5
Bipolar Wound
Motor
NOTES: A. Traces in bold are high current traces.
B. C1 should be placed as close as possible to terminals 1 and 4.
Figure 9. Application Schematic
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
A
D
Hall
Sensor
C
B
SLIS101A − MAY 2001
MECHANICAL DATA
DGN (S-PDSO-G8)
PowerPAD PLASTIC SMALL-OUTLINE PACKAGE
0,38
0,25
0,65
8
0,25 M
5
Thermal Pad
(See Note D)
0,15 NOM
3,05
2,95
4,98
4,78
Gage Plane
0,25
1
0°−ā 6°
4
3,05
2,95
0,69
0,41
Seating Plane
1,07 MAX
0,15
0,05
0,10
4073271/A 04/98
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions include mold flash or protrusions.
The package thermal performance may be enhanced by attaching an external heat sink to the thermal pad.
This pad is electrically and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MO-187
PowerPAD is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
PACKAGE OPTION ADDENDUM
www.ti.com
8-Apr-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
THMC45DGN
OBSOLETE
MSOPPower
PAD
DGN
8
TBD
Call TI
Call TI
THMC45DGNR
OBSOLETE
MSOPPower
PAD
DGN
8
TBD
Call TI
Call TI
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated