ETC CX42053

CX42053
700 – 1000 MHz High Dynamic Range, Diversity Receiver Front End
Skyworks’ CX42053 is an integrated, high-dynamic range, low-noise receiver down
converter for two-channel diversity systems. It includes a Low Noise Amplifier
(LNA) followed by a double-balanced active mixer. The CX42053 has dual Local
Oscillator (LO) inputs, selected using an external switch interface. The internal
attenuator is integrated with the LNA. The attenuator function is also controlled
using an externally controlled CMOS-compatible interface.
Figure 1 shows a functional block diagram for the CX42053. The 24-pin Plastic
Quad Flat Pack (PQFP) device package and pinout are shown in Figure 2.
Distinguishing Features
• High 3rd Order Input Intercept Point (IIP3) mixer
and LNA
• Wideband RF input frequency range
(700 to 1000 MHz)
• Single or two-channel applications
• Use with LNA-mixer cascaded or mixer-only
• Bias-selectable LNA/mixer functions
• Integrated solid state attenuator
• CMOS-compatible control interfaces
• ±5 V supply operation
• –20 °C to +85 °C operating range
• Supports frequency hopping applications
Applications
•
•
•
•
Cellular and GSM communications
Mobile radio systems
Paging
Industrial, Scientific, Medical (ISM) band
Applications
IR FILTER
L_GNDA
L_OUTA
MGNDA
M_INPA
M_INNA
IF A
RF A
LNA_INA
RF
Balun
24
23
22
21
20
19
LNA
Attenuator
ATTN CONTROL
LO 1
LO 2
LO SELECT
Amp
Attenuator
GND
1
LO_1
2
ATTN
3
LO_SEL
4
LO_2
5
VSS
6
7
8
9
10
11
12
L_OUTB
MGNDB
M_INPB
M_INNB
RF
Balun
L_GNDB
LNA
LNA_INB
IF B
RF B
18
IFNA
17
IFPA
16
LO_GND
15
VDD
14
IFPB
13
IFNB
IR FILTER
C1249
Figure 1. CX42053 Functional Block Diagram
Data Sheet
C1250
Figure 2. CX42053 Pinout – 24-Pin PQFP Package
Skyworks
Proprietary Information and Specifications Are Subject to Change
Doc. No. 101431B
March 12, 2002
CX42053
Diversity Receiver Front End
Technical Description
The CX42053 consists of two identical channels, A and B, that
were specifically designed for the purpose of diversity in base
station applications.
Each channel consists of a single-ended LNA and a doublebalanced differential mixer. The LNAs share a common CMOScompatible attenuator control switch, which bypasses the LNA,
providing 20 dB of attenuation.
Each channel shares two independent LO signals, LO1 and
LO2, that are selected using a common CMOS-compatible
control signal. With this ability, the device can be used in
applications where frequency hopping is required.
The LNAs and mixers are independently biased. This allows
design flexibility with power management functions in base
station receivers.
Electrical and Mechanical Specifications
The signal pin assignments and functions are described in
Table 1. The absolute maximum ratings of the CX42053 are
provided in Table 2. The recommended operating conditions are
specified in Table 3 and electrical specifications are provided in
Table 4. Table 5 provides additional electrical specifications for
full channel performance.
Typical performance characteristics of the CX42053 are
illustrated in Figures 3 through 9.
Table 1. CX42053 Signal Descriptions
Pin #
2
Name
Description
Pin #
Name
Description
1
GND
Ground
13
IFNB
Channel B negative differential mixer IF output
2
LO_1
Local oscillator 1 input for channels A and B
14
IFPB
Channel B positive differential mixer IF output
3
ATTN
Channels A and B attenuator control
15
VDD
Positive supply voltage
4
LO_SEL
LO_1/LO_2 select control
16
LO_GND
Local oscillator ground
5
LO_2
Local oscillator 2 input for channels A and B
17
IFPA
Channel A positive differential mixer IF output
6
VSS
Negative supply voltage
18
IFNA
Channel A negative differential mixer IF output
7
LNA_INB
Channel B LNA input
19
M_INNA
Channel A negative differential mixer input
8
L_GNDB
Channel B LNA ground
20
M_INPA
Channel A positive differential mixer input
9
L_OUTB
Channel B LNA output
21
MGNDA
Channel A mixer ground
10
MGNDB
Channel B mixer ground
22
L_OUTA
Channel A LNA output
11
M_INPB
Channel B positive differential mixer input
23
L_GNDA
Channel A LNA ground
12
M_INNB
Channel B negative differential mixer input
24
LNA_INA
Channel A LNA input
Skyworks
Proprietary Information and Specifications Are Subject to Change
101431B
March 12, 2002
Diversity Receiver Front End
CX42053
Table 2. CX42053 Absolute Maximum Ratings
Parameter
Symbol
Min
Typical
Max
Units
+5.5
V
Positive DC power supply
VDD
Negative DC power supply
VSS
–6.0
V
PD
2.25
W
Power dissipation
Input power
PIN
Thermal resistance
RTH
+15
Operating temperature
TOPR
–20
+85
°C
Storage temperature
TSTG
–40
+125
°C
+25
dBm
°C/W
Note: No damage to device if only one parameter is applied at a time with other parameters at nominal conditions.
Table 3. CX42053 Recommended Operating Conditions
Parameter
Symbol
Min
Typical
Max
Units
VDD
+4.75
+5.0
+5.25
V
Negative DC supply voltage
VSS
–4.75
–5.0
–5.25
V
Operating temperature
TOPR
0
+50
°C
Positive DC supply voltage
101431B
March 12, 2002
Skyworks
Proprietary Information and Specifications Are Subject to Change
3
CX42053
Diversity Receiver Front End
Table 4. CX42053 Electrical Characteristics
(+25°° C, Voltage Supply = ±5 V, LO = 0 dBm, RF Frequency = 900 MHz, IF Frequency = 110 MHz, Mixer Bias = 55 mA)
Parameter
Test Condition
Min
Typical
12
14
Max
Units
Low Noise Amplifier
Gain
Noise Figure (NF)
1.8
Input IP3
–1 dB compression point
dB
3.0
dB
16
18
dBm
3
5
dBm
RF
RF input frequency
700
1000
MHz
2.0:1
VSWR
RF input (Note 1)
RF = 700 MHz to 1000 MHz
1.5:1
RF = 900 MHz, 50 Ω
1.5:1
2.0:1
VSWR
RF output (Note 1)
RF = 700 MHz to 1000 MHz
1.5:1
2.0:1
VSWR
Conversion gain
RF = 800 to 900 MHz, LO = 750 MHz
–0.5
+1.0
dB
RF = 800 to 900 MHz, LO = 950 MHz
Mixer (Note 2)
SSB NF
Input IP3
–0.5
+1.0
dB
RF = 900 MHz, LO = 790 MHz
0
+2.0
dB
RF = 900 MHz, LO = 1010 MHz
0
+1.5
dB
RF = 800 MHz to 1000 MHz, LO = 690 MHz
10
13
dB
RF = 700 MHz to 1000 MHz, LO = 1010 MHz
10
13
dB
RF = 900 MHz, LO= 790 MHz (mixer bias = 80 mA)
+23
+27
dBm
RF = 900 MHz, LO = 790 MHz
+19
+23
dBm
RF = 900 MHz, LO = 1010 MHz
+18
+22
dBm
RF to IF leakage
RF = 900 MHz, LO = 790 MHz
–50
dBm
RF = 900 MHz, LO = 1010 MHz
–50
dBm
LO to IF leakage
LO = 790 MHz
–45
dBm
LO = 1010 MHz
–50
dBm
dBm
–1dB compression point
(mixer bias = 80 mA)
+14
+18
–1 dB compression point
+10
+14
dBm
–70
dBc
1000
MHz
1.5:1
2.0:1
VSWR
0
+5
dBm
250
MHz
2.0:1
2.0:1
VSWR
VSWR
–75
1/2 IF product suppression
Local Oscillator
LO input frequency
LO input (Note 1)
700
50 Ω
LO level input
–5
Intermediate Frequency
IF output frequency
IF output (Note 1)
50
50 Ω, IF = 50 MHz to 150 MHz
50 Ω, IF = 110 MHz
1.5:1
1.5:1
Note 1: In a 50 Ω system obtained with external matching components on input/output ports. See Figure 10 and Table 6 for matching network configuration and
element values.
Note 2: Include RF balun and IF transformer losses.
4
Skyworks
Proprietary Information and Specifications Are Subject to Change
101431B
March 12, 2002
Diversity Receiver Front End
CX42053
Table 5. Full Channel Performance
(+ 25°° C, Voltage Supply = ±5 V, LO = 0 dBm, RF Frequency = 900 MHz, IF Frequency = 110 MHz)
Parameter
Test Condition
Min
RF input (Note 1)
NF (Note 2)
Gain (Note 3)
Input IP3 (Note 4)
1 dB compression point (Note 5)
Typical
Max
Units
1.5:1
2.0:1
VSWR
3.0
5.5
dB
11
15
dB
mixer bias = 80 mA
9
13
dBm
mixer bias = 55 mA
5.5
9.5
dBm
mixer bias = 80 mA
+1
+5
dBm
mixer bias = 55 mA
–3
+1
dBm
1/2 IF product suppression
–70
Channel A to B isolation
35
LO leakage at RF input
–40
LO1 to LO2 isolation
35
Supply current @ +5.0 V, both channels
Supply current @ –5.0 V, both channels
–60
40
dB
–35
dBm
360
15
mA
mA
40
340
10
dBc
dB
Note 1: In a 50 Ω system obtained with external matching network on LNA and mixer input ports. See Figure 10 and Table 6 for network elements and
frequency ranges.
Note 2: Calculated using the following equation: NFCascaded
æ æ NFLNA ö æ æçç NFMixer + Loss IRfilter ö÷÷ ö ö
ç ç
÷÷
÷ ç ç
÷
10
ø
ç è 10 ø ç 10 è
− 1 ÷÷
= 10 × Log ç 10
+ç
÷÷
æ
ö
ç GLNA ÷
ç
ç
÷
÷÷
ç
ç 10 ÷
ø
÷÷
ç
ç
10 è
øø
è
è
Note 3: Calculated using the following equation: ConversionGainCascaded = GLNA − LossIRfilter + GMixer
−1
æé
ù ö÷
ç
ú ÷
çê
ú ÷
ê
1
1
Note 4: Calculated using the following equation: IIP3 = 10 × Log ç ê
+
ú
ç ê æ IIP3Mixer − (GLNA − Loss IRfilter ) ö
æ IIP 3LNA ö ú ÷
÷
ç
ç
÷
çê ç
ç
÷ú ÷
÷
10
ç êë 10 è
ø 10 è 10 ø úû ÷
è
ø
Note 5: Calculated using the following equation: P1dB , system = ( P1dB , Mixer − (GLNA − Loss IRfilter )) or ( P1dB , LNA ), whichever is less
101431B
March 12, 2002
Skyworks
Proprietary Information and Specifications Are Subject to Change
5
CX42053
Diversity Receiver Front End
Figure 3. LNA
(IIP3 = +17 dBm, Input Power = –20 dBm)
Figure 4. Mixer With High Side LO
(IIP3 = +26 dBm, Input Power = –10 dBm)
6
Skyworks
Proprietary Information and Specifications Are Subject to Change
101431B
March 12, 2002
Diversity Receiver Front End
CX42053
Figure 5. Mixer With Low Side LO
(IIP3 = +25 dBm, Input Power = –10 dBm)
25
4.5
4
3.5
15
3
2.5
10
NF (dB)
Gain (dB )/ IIP3(dBm)
20
Gain
IIP3
NF
2
5
1.5
0
1
700
800
900
1000
Frequency (MHz)
Figure 6. LNA Gain, NF, and IIP3 vs Frequency
(Values Obtained With a 900 MHz Input Match)
101431B
March 12, 2002
Skyworks
Proprietary Information and Specifications Are Subject to Change
7
CX42053
Diversity Receiver Front End
85
Mixer Bias Current (mA)
80
75
70
65
60
55
50
45
40
35
5
10
15
20
Bias Resistor (Ohms)
3
10
2.8
9.8
2.6
9.6
2.4
9.4
2.2
9.2
2
9
1.8
8.8
1.6
8.6
1.4
8.4
1.2
8.2
1
NF (dB)
Conv. Gain (dB)
Figure 7. Mixer Bias Current vs. Bias Resistor (RA2, RB2)
Conv. Gain
NF
8
35
55
75
Mixer Bias Current (mA)
27
20
25
18
23
16
21
14
19
12
17
P1dB (dBm)
IIP3 (dBm)
Figure 8. Mixer Conversion Gain and Noise Figure vs. Bias Current
IIP3
P1dB
10
35 40 45 50 55 60 65 70 75 80 85
Mixer Bias Current (mA)
Figure 9. Mixer IIP3 and –1 dB Compression Point vs. Mixer Bias Current
8
Skyworks
Proprietary Information and Specifications Are Subject to Change
101431B
March 12, 2002
Diversity Receiver Front End
CX42053
Evaluation Board Description
LNA Testing Procedure_______________________________
The CX42053 Evaluation Board is used to test the CX42053
mixer and LNA performance. The CX42053 Evaluation Board
schematic diagram is shown in Figure 10. Table 6 contains I/O
matching network components used in the schematic. The
schematic shows the basic design of the Evaluation Board for
the RF range of 800 to 1000 MHz. The IF matching circuitry has
been optimized for 60 to 130 MHz. Figure 11 displays the
Evaluation Board layout.
Use the following procedure to set up the CX42053 Evaluation
Board for LNA testing. Refer to Figure 12 for guidance:
1.
Set all the DIP switches to OFF. For information on the
switch settings, refer to Table 7.
2.
Connect the CX42053 Evaluation Board to ±5 VDC power
supplies using insulated supply cables. VDD should be set
to +5.0 V and VSS to –5.0 V. If available, enable the
current limiting function of the power supplies as follows:
Circuit Design Configurations ________________________
+ 5 VDC supply current limit = 200 mA
–5 VDC supply current limit = 50 mA
The following design considerations are general in nature and
must be followed regardless of final use or configuration:
1.
Paths to ground should be made as short as possible.
2.
The downset paddle of the PQFP provides necessary
electrical grounding and is the main thermal conduit for
heat dissipation. Any printed circuit board using the
CX42053 must have sufficient solder mask clearance
beneath the IC (i.e., approximately 110 percent of the
downset paddle). This provides adequate solder coverage
for the downset paddle and minimizes excessive lead
standoff. Multiple vias to the grounding layer beneath the
device are required for maximum thermal relief.
3.
4.
5.
Connect red and yellow banana plugs to VDD, a purple
plug to VSS, and a black plug to ground. Connect a threeslot plug to the side (JP1) and a two-slot plug to the top
(JP2).
The inclusion of external bypass capacitors on the VSS
and VDD voltage inputs of the LNAs and mixers is
recommended. The application schematic in Figure 10
shows these capacitors (1000 pF and 12 pF) in shunt with
each control switch, as well as the VSS supply. The
1000 pF capacitor serves as a low frequency bypass, while
the 12 pF capacitor prevents any RF signals from coupling
on to the DC supply voltages. It is recommended that the
bypass capacitors be placed as close as possible to the
CX42053 for best results.
The LNA receives its bias voltage via the LNA output pin.
The use of a blocking capacitor (RF short) on the LNA
input/output and mixer input is required.
Ceramic or wire-wound balanced transformers (baluns)
may be used to provide the differential input to the active
mixer. The secondary center tap of these baluns provides
the DC return path for the mixer bias current. Balun
selection criterion should include DC current handling
capability, differential phase/amplitude balance, insertion
loss, and temperature performance.
6.
The application of an image-reject filter between the LNA
and mixer is recommended.
7.
For proper switching of the control interface circuits, the
following conditions must be met:
OFF: 0 VDC ≤ VIN ≤ 0.5 VDC @ 30 µA
ON: 3.0 VDC ≤ VIN ≤ VDD @ 120 µA
101431B
March 12, 2002
3.
Connect a signal generator to the LNA A input port (J1).
Set the generator to the desired RF frequency at a power
level of –20 dBm, but do not enable.
4.
Connect a spectrum analyzer to the output port of LNA A
(J2).
5.
Enable the power supply by turning switches #2 and #4
ON.
6.
Enable the RF signal and take measurements.
7.
Repeat steps 3 through 6 for LNA B, but use switches #4
and #5 to enable the power supply.
Mixer Testing Procedure______________________________
Use the following procedure to set up the CX42053 Evaluation
Board for mixer testing. Refer to Figure 13 for guidance:
1.
Set all the DIP switches to OFF. For information on the
switch settings, refer to Table 7.
2.
Connect the CX42053 Evaluation Board to ±5 VDC power
supplies using insulated supply cables. VDD should be set
to +5.0 V and VSS to –5.0 V. If available, enable the
current limiting function of the power supplies as follows:
+ 5 VDC supply current limit = 200 mA
–5 VDC supply current limit = 50 mA
Connect red and yellow banana plugs to VDD, a purple
plug to VSS, and a black plug to ground. Connect a threeslot plug to the side (JP1) and a two-slot plug to the top
(JP2).
3.
Connect a signal generator to the LO1 input port (J9). Set
the generator to the desired LO frequency at a power level
of 0 dBm, but do not enable.
Skyworks
Proprietary Information and Specifications Are Subject to Change
9
CX42053
Diversity Receiver Front End
MIXER_IN_A
SMA
1 2
CA11
8.2 pF
LA5
10 nH
SW1
J2
LNA_OUT_A
CA16
DNI
CA5
39 pF
CA9
3.9 pF
CA2
39 pF
+5 V
LDB20C500A0800
1
CA10
1000 pF
Switch 1-7
3
4
18
1
ATTEN_CTL
LO_SELECT
C3
39 pF
L2
12 nH
J10
LA4
100 nH
16
4
15
5
14
SMA
6
C1
1000 pF
D2
1N4736A-010
1
SMA
4
Switch 1-4
C8
39 pF
3
T4
13
C7
39 pF
1
C4
1000 pF
6
2
–5V
CA4
10 pF
TC4-1W
3
C6
22 pF
LO2_IN
IF_OUT_A
6
1
17
2
pin 25
Switch 1-6
T2
2
C2
39 pF
4
LB4
100 nH
J8
IF_OUT_B
CB4
10 pF
TC4-1W
25
1
SMA
Switch 1-3
CB10
1000 pF
12
11
10
9
8
7
CB8
39 pF
2
CB6
1000 pF
LDB20C500A0800
T3
LB2
5.6 nH
Switch 1-5
4
CB15
DNI
6
CB1
33 pF
CB3
1.0 pF
3
LNA_IN_B
SMA
1
LB1
6.8 nH
J5
CB2
39 pF
CB9
39 pF
J6
1
–5 V
19
20
21
24
22
CA8
39 pF
J4
L1
12 nH
1
1
2
3
LO1_IN
SMA
1
JP1
Header 3
Switch 1-1
C5
22 pF
J9
D1
1N4736A-010
CA15
DNI
CA3
1.0 pF
23
LNA_IN_A
LA1
6.8 nH
6
CA1
33 pF
1
T1
1
Monitor
SW DIP-7
3
CA6
1000 pF
SMA
RA1
10
LA2
5.6 nH
Switch 1-2
J1
CA7
1000 pF
14
13
12
11
10
9
8
2
1
SMA
1
2
3
4
5
6
7
sw 1-1
sw 1-2
sw 1-3
sw 1-4
sw 1-5
sw 1-6
sw 1-7
1
1
JP2
Header 2
LA3
4.7 nH
J3
LNA_OUT_B
CB5
39 pF
CB16
DNI
SMA
CB11
8.2 pF
CB7
1000 pF
RB1
10
LB3
4.7 nH
J7
1
MIXER_IN_B
LB5
10 nH
SMA
C1254
Figure 10. CX42053 Application Schematic
Table 6. Input/Output Matching Network Components for Application Schematic
RF Frequency
LA1, LB1
CA3, CB3
CA9, CB9
CA16, CB16
T1, T2
CA11, CB11
LA5, LB5
LA3, LB3
800-1000 MHz
6.8 nH
1.0 pF
3.9 pF
DNI
LDB20C500A800
4.7 pF
15 nH
33 nH
700-800 MHz
(Note 1)
6.8 nH
1.0 pF
3.9 pF
DNI
LDB20C500A800
8.2 pF
10 nH
4.7 pF
LA4, LB4
CA4, CB4
40-80 MHz (Note 2)
IF Frequency
150 nH
10 pF
70-200 MHz
100 nH
10 pF
Note 1: Standard Evaluation Kit TW11-D222 is optimized for the 850 to 1000 MHz frequency range. The schematic diagram shown in Figure 10 applies to Evaluation
Kit TW11-D222.
Note 2: For the stated values, CA4 and CB4 need to be moved to the side of LA4 and LB4 closest to the CX42053.
Data Sheet
Skyworks
Proprietary Information and Specifications Are Subject to Change
Doc. No. 101431B
March 12, 2002
Diversity Receiver Front End
CX42053
J1
J2
J3
J4
C
A1
LA3
CA10
LA4
C8
C4
T2
CB10
T1
D1
SW1
CA8
CA7
CA5
CA4
RA1
CB8
CA2
CA6
LA2
LA1
CA15
CA16
C5
L1
J9
LA5
CONEXANT SYS, INC
CX42053 EVAL FIXTURE
CA11
A3
CA9
C
C2
U1
LB4
CB4
CB5
JP2
CB7
JP1
RB1
CB11
LB3
CB16
LB5
C
T4
T3
CB9
CB2
CB6
LB2
LB1
CB15
L2
J10
C6
C7
C3
D2
C
B3
B1
J5
TW11–D220–
J6
J7
J8
C1270
Figure 11. CX42053 Evaluation Board Layout
RF Signal
Generator
Spectrum
Analyzer
ON
J1
J2
J3
J4
1
2
3
4
5
6
7
DIP switch settings for LNA A
CONEXANT SYS, INC
CX42053 EVAL FIXTURE
ON
1
J9
2
3
4
5
6
7
DIP switch settings for LNA B
J10
JP2
JP1
J5
J6
J7
+5 VDC
GND
–5 VDC
Power
Supply
J8
C1316
Figure 12. CX42053 Evaluation Board LNA Testing Configuration
101431B
March 12, 2002
Skyworks
Proprietary Information and Specifications Are Subject to Change
11
CX42053
Diversity Receiver Front End
Table 7. CX42053 Switch Pack Description
Switch
Name
Description
#1
VMIX_A
ON enables mixer A
#2
VLNA_A
ON enables LNA A
#3
VMIX_B
ON enables mixer B
#4
VDD
ON enables VDD
#5
VLNA_B
ON enables LNA B
#6
VLOSELECT
ON selects LO1, OFF selects LO2
#7
VATTENUATOR
ON enables attenuation
RF Signal
Generator
Spectrum
Analyzer
ON
J1
J2
J3
J4
1
2
3
4
5
6
7
DIP switch settings for mixer A
CONEXANT SYS, INC
CX42053 EVAL FIXTURE
RF Signal
Generator
ON
1
J9
2
3
4
5
6
7
DIP switch settings for mixer B
J10
JP2
JP1
J5
J6
J7
+5 VDC
GND
–5 VDC
Power
Supply
J8
C1317
Figure 13. CX42053 Evaluation Board Mixer Testing Configuration
12
Skyworks
Proprietary Information and Specifications Are Subject to Change
101431B
March 12, 2002
Diversity Receiver Front End
CX42053
4.
Connect a signal generator to the Mixer A input port (J3).
Set the generator to the desired RF frequency at a power
level of 0 dBm, but do not enable.
after the container seal is broken must be followed. Otherwise,
problems related to moisture absorption may occur when the
part is subjected to high temperature during solder assembly.
5.
Connect a spectrum analyzer to the output port of Mixer A
(J4).
6.
Enable the power supply by turning switches #1 and #4
ON.
7.
Enable LO1 by turning switch #6 ON.
If the part is attached in a reflow oven, the temperature ramp
rate should not exceed 10 °C per second. Maximum
temperature should not exceed 225 °C and the time spent at a
temperature that exceeds 210 °C should be limited to less than
10 seconds. If the part is manually attached, precaution should
be taken to ensure that the part is not subjected to a
temperature that exceeds 300 °C for more than 10 seconds.
8.
Enable the LO signal, then enable the RF signal and take
measurements.
9.
Repeat steps 4 through 8 for mixer B, but use switches #3
and #4 to enable the power supply. If LO2 is desired, turn
switch #6 OFF and connect the LO signal generator to the
LO2 input port (J10).
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment. For
additional details on both attachment techniques, precautions,
and recommended handling procedures, refer to the Skyworks’
document Solder Reflow Application Note, document number
101536.
Caution: If any of the input signals exceed the rated maximum
values, the CX42053 Evaluation Board can be
permanently damaged.
Package Dimensions
Production quantities of this product are shipped in a standard
tape and reel format. For packaging details, refer to the
Skyworks’ document Tape and Reel Information Application
Note, document number 101568.
Electro-Static Discharge (ESD) Sensitivity
Figure 14 shows the package dimensions for the 24-pin
CX42053 PQFP and Figure 15 provides the tape and reel
dimensions.
The CX42053 is a static-sensitive electronic device. Do not
operate or store near strong electrostatic fields. Take proper
ESD precautions.
Package and Handling Information
Since the device package is sensitive to moisture absorption, it
is baked and vacuum packed before shipping. Instructions on
the shipping container label regarding exposure to moisture
11.07 ± 0.15
8.05 ± 0.05
2.125 ± 0.075
8.05 ± 0.05
0.505 ± 0.025
Pin #1
0.05 typical
8.05 ± 0.05
11.07 ± 0.15
0.25 typical
1.27 ± 0.25 typical
6.35 ± 0.25
5 Equal Spaces
All measurements are in millimeters
C1251
Figure 14. CX42053 24-Pin PQFP Package Dimension Drawing
101431B
March 12, 2002
Skyworks
Proprietary Information and Specifications Are Subject to Change
13
CX42053
Diversity Receiver Front End
1.50 ± 0.10
B
A
2.00 ± 0.10
1.75 ± 0.10
11.50 ± 0.10
4.00 ± 0.10
A
24.00 +0.30/-0.10
16.00 ± 0.10
1.50 ± 0.25
B
0.330 ± 0.013
5o max
5o max
NOTE:
1. Carrier tape: black conductive polycarbonate.
2. Cover tape material: transparent conductive PSA.
3. Cover tape size: 21.3 mm width.
4. All dimensions are in millimeters.
2.29 ± 0.10
11.43± 0.10
A
11.35 ± 0.10
B
C1271
Figure 15. CX42053 24-Pin PQFP Tape and Reel Dimensions
14
Skyworks
Proprietary Information and Specifications Are Subject to Change
101431B
March 12, 2002
Diversity Receiver Front End
CX42053
Ordering Information
Model Name
Ordering Part Number
Evaluation Kit Part
Number
CX42053 700-1000 MHz
Receiver Front End/Downconverter
CX42053-11
TW11-D222
© 2002, Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products. These materials are provided by Skyworks as a service to its
customers and may be used for informational purposes only. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to
its products, specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility
whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its products and product descriptions.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as may be provided in Skyworks’ Terms and
Conditions of Sale for such products, Skyworks assumes no liability whatsoever.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF
SKYWORKS™ PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY
OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE
ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL
NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST
PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS.
Skyworks™ products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks’ customers using or selling Skyworks™ products for use in such
applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
The following are trademarks of Skyworks Solutions, Inc.: Skyworks™, the Skyworks symbol, and “Breakthrough Simplicity”™. Product names or services listed in this
publication are for identification purposes only, and may be trademarks of third parties. Third-party brands and names are the property of their respective owners.
Additional information, posted at www.skyworksinc.com, is incorporated by reference.
101431B
March 12, 2002
Skyworks
Proprietary Information and Specifications Are Subject to Change
15
General Information:
Skyworks Solutions, Inc.
4311 Jamboree Rd.
Newport Beach, CA 92660-3007
www.skyworksinc.com