Technical Data Sheet

Ultralow Distortion
Differential ADC Driver
ADA4938-1/ADA4938-2
13 –VS
16 –VS
15 –VS
06592-001
+VS 7
9 VOCM
+VS 8
10 +OUT
+FB 4
+VS 5
11 –OUT
–IN 3
24
23
22
21
20
19
+IN1
–FB1
–VS1
–VS1
PD1
–OUT1
Figure 1. ADA4938-1 Functional Block Diagram
1
2
3
4
5
6
ADA4938-2
18
17
16
15
14
13
+OUT1
VOCM1
–VS2
–VS2
PD2
–OUT2
–IN2
+FB2
+VS2
+VS2
VOCM2
+OUT2
06592-202
7
8
9
10
11
12
–IN1
+FB1
+VS1
+VS1
–FB2
+IN2
ADC drivers
Single-ended-to-differential converters
IF and baseband gain blocks
Differential buffers
Line drivers
Figure 2. ADA4938-2 Functional Block Diagram
–50
G
G
G
G
–60
–70
The ADA4938-x is a low noise, ultralow distortion, high speed
differential amplifier. It is an ideal choice for driving high performance ADCs with resolutions up to 16 bits from dc to 27 MHz,
or up to 12 bits from dc to 74 MHz. The output common-mode
voltage is adjustable over a wide range, allowing the ADA4938 to
match the input of the ADC. The internal common-mode
feedback loop also provides exceptional output balance as well
as suppression of even-order harmonic distortion products.
–80
SFDR (dBc)
GENERAL DESCRIPTION
The ADA4938-x is fabricated using the Analog Devices, Inc.,
proprietary third generation, high voltage XFCB process, enabling
it to achieve very low levels of distortion with an input voltage
noise of only 2.6 nV/√Hz. The low dc offset and excellent dynamic
performance of the ADA4938-x make it well-suited for a wide
variety of data acquisition and signal processing applications.
12 PD
+IN 2
APPLICATIONS
= +2,
= +2,
= +2,
= +2,
VO, dm = 5V p-p
VO, dm = 3.2V p-p
VO, dm = 2V p-p
VO, dm = 1V p-p
–90
–100
–110
–120
–130
1
10
FREQUENCY (MHz)
100
06592-002
Full differential and single-ended-to-differential gain configurations
are easily realized with the ADA4938-x. A simple external feedback
network of four resistors determines the closed-loop gain of the
amplifier.
ADA4938-1
–FB 1
+VS 6
Extremely low harmonic distortion (HD)
−106 dBc HD2 @ 10 MHz
−82 dBc HD2 @ 50 MHz
−109 dBc HD3 @ 10 MHz
−82 dBc HD3 @ 50 MHz
Low input voltage noise: 2.6 nV/√Hz
High speed
−3 dB bandwidth of 1000 MHz, G = +1
Slew rate: 4700 V/μs
0.1 dB gain flatness to 150 MHz
Fast overdrive recovery of 4 ns
1 mV typical offset voltage
Externally adjustable gain
Differential-to-differential or single-ended-to-differential
operation
Adjustable output common-mode voltage
Wide supply voltage range: +5 V to ±5 V
Single or dual amplifier configuration available
14 –VS
FUNCTIONAL BLOCK DIAGRAMS
FEATURES
Figure 3. SFDR vs. Frequency and Output Voltage
The ADA4938-1 (single amplifier) is available in a Pb-free,
3 mm × 3 mm, 16-lead LFCSP. The ADA4938-2 (dual
amplifier) is available in a Pb-free, 4 mm × 4 mm, 24-lead
LFCSP. The pinouts have been optimized to facilitate layout and
minimize distortion. The parts are specified to operate over the
extended industrial temperature range of −40°C to +85°C.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2007–2009 Analog Devices, Inc. All rights reserved.
ADA4938-1/ADA4938-2
TABLE OF CONTENTS
Features .............................................................................................. 1 Theory of Operation ...................................................................... 19 Applications ....................................................................................... 1 Analyzing an Application Circuit ............................................ 19 General Description ......................................................................... 1 Setting the Closed-Loop Gain .................................................. 19 Functional Block Diagrams ............................................................. 1 Estimating the Output Noise Voltage ...................................... 19 Revision History ............................................................................... 2 The Impact of Mismatches in the Feedback Networks ......... 20 Specifications..................................................................................... 3 Calculating the Input Impedance of an Application Circuit 20 Dual-Supply Operation ............................................................... 3 Single-Supply Operation ............................................................. 5 Input Common-Mode Voltage Range in Single-Supply
Applications ................................................................................ 20 Absolute Maximum Ratings............................................................ 7 Terminating a Single-Ended Input .......................................... 21 Thermal Resistance ...................................................................... 7 Setting the Output Common-Mode Voltage .......................... 21 ESD Caution .................................................................................. 7 Layout, Grounding, and Bypassing .............................................. 23 Pin Configurations and Function Descriptions ........................... 8 High Performance ADC Driving ................................................. 24 Typical Performance Characteristics ............................................. 9 Outline Dimensions ....................................................................... 25 Test Circuts ...................................................................................... 17 Ordering Guide .......................................................................... 25 Terminology .................................................................................... 18 REVISION HISTORY
10/09—Rev. 0 to Rev. A
Added Settling Time Parameter, Table 1 ....................................... 3
Changes to Linear Output Current Parameter, Table 1 ............... 3
Added Settling Time Parameter, Table 3 ....................................... 5
Changes to Linear Output Current Parameter, Table 3 ............... 5
Changes to Figure 5 and Figure 6 ................................................... 8
Added EP Row to Table 7 and EP Row to Table 8........................ 8
Changes to Figure 41 ...................................................................... 14
Added New Figure 53, Renumbered Sequentially ..................... 16
Changes to Table 9 .......................................................................... 19
Added Exposed Pad Notation to Outline Dimensions ............. 25
Changes to Ordering Guide .......................................................... 25
11/07—Revision 0: Initial Version
Rev. A | Page 2 of 28
ADA4938-1/ADA4938-2
SPECIFICATIONS
DUAL-SUPPLY OPERATION
TA = 25°C, +VS = 5 V, −VS = −5 V, VOCM = 0 V, RT = 61.9 Ω, RG = RF = 200 Ω, G = +1, RL, dm = 1 kΩ, unless otherwise noted.
All specifications refer to single-ended input and differential output, unless otherwise noted. For gains other than G = +1, values for RF
and RG are shown in Table 11.
±DIN to ±OUT Performance
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
IP3
Input Voltage Noise
Noise Figure
Input Current Noise
Crosstalk (ADA4938-2)
INPUT CHARACTERISTICS
Offset Voltage
Conditions
Min
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Output Balance Error
Max
Unit
VOUT = 0.1 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p
VIN = 5 V to 0 V step, G = +2
1000
150
800
4700
6.5
4
MHz
MHz
MHz
V/μs
ns
ns
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
f1 = 30.0 MHz, f2 = 30.1 MHz
f = 30 MHz, RL, dm = 100 Ω
f = 10 MHz
G = +4, f = 10 MHz
f = 10 MHz
f = 100 MHz
−106
−82
−109
−82
89
45
2.6
15.8
4.8
−85
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
dB
pA/√Hz
dB
VOS, dm = VOUT, dm/2; VDIN+ = VDIN− = 0 V
TMIN to TMAX variation
∆VOUT, dm/∆VIN, cm; ∆VIN, cm = ±1 V, f = 1 MHz
1
±4
−13
−0.01
6
3
1
−VS + 0.3 to +VS − 1.6
−75
Maximum ∆VOUT; single-ended output
Per amplifier, RL, dm = 20 Ω, f = 10 MHz
∆VOUT, cm/∆VOUT, dm; ∆VOUT, dm = 1 V; f = 10 MHz
−VS + 1.2 to +VS − 1.2
±75
−60
Input Bias Current
Input Resistance
Typ
−18
TMIN to TMAX variation
Differential
Common mode
Rev. A | Page 3 of 28
4
mV
μV/°C
μA
μA/°C
MΩ
MΩ
pF
V
dB
V
mA
dB
ADA4938-1/ADA4938-2
VOCM to ±OUT Performance
Table 2.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
Input Voltage Noise (RTI)
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
POWER DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Bias Current
Enabled
Disabled
Conditions
Min
VIN = −3.4 V to +3.4 V, 25% to 75%
VOS, cm = VOUT, cm; VDIN+ = VDIN− = 0 V
∆VOUT, dm/∆VOCM; ∆VOCM = ±1 V
∆VOUT, cm/∆VOCM; ∆VOCM = ±1 V
0.95
Typ
Max
Unit
230
1700
7.5
MHz
V/μs
nV/√Hz
−VS + 1.3 to +VS − 1.3
10
3
0.5
−81
1.00
V
kΩ
mV
μA
dB
V/V
4.5
1.05
11
40
V
mA
μA/°C
mA
dB
Per amplifier
TMIN to TMAX variation
Powered down
∆VOUT, dm/∆VS; ∆VS = ±1 V
37
40
2.0
−80
Powered down
Enabled
≤2.5
≥3
1
200
V
V
μs
ns
PD = 5 V
PD = −5 V
1
−760
μA
μA
OPERATING TEMPERATURE RANGE
−40
Rev. A | Page 4 of 28
3.0
+85
°C
ADA4938-1/ADA4938-2
SINGLE-SUPPLY OPERATION
TA = 25°C, +VS = 5 V, −VS = 0 V, VOCM = +VS/2, RT = 61.9 Ω, RG = RF = 200 Ω, G = +1, RL, dm = 1 kΩ, unless otherwise noted.
All specifications refer to single-ended input and differential output, unless otherwise noted. For gains other than G = 1, values for RF and
RG are shown in Table 11.
±DIN to ±OUT Performance
Table 3.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
Input Voltage Noise
Noise Figure
Input Current Noise
Crosstalk (ADA4938-2)
INPUT CHARACTERISTICS
Offset Voltage
Conditions
Min
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Output Balance Error
Max
Unit
VOUT = 0.1 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p
VIN = 2.5 V to 0 V step, G = +2
1000
150
750
3900
6.5
4
MHz
MHz
MHz
V/μs
ns
ns
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
f = 10 MHz
G = +4, f = 10 MHz
f = 10 MHz
f = 100 MHz
−110
−79
−100
−79
2.6
15.8
4.8
−85
dBc
dBc
dBc
dBc
nV/√Hz
dB
pA/√Hz
dB
VOS, dm = VOUT, dm/2; VDIN+ = VDIN− = VOCM = 2.5 V
TMIN to TMAX variation
∆VOUT, dm/∆VIN, cm; ∆VIN, cm = ±1 V
1
±4
−13
−0.01
6
3
1
−VS + 0.3 to +VS − 1.6
−80
Maximum ∆VOUT; single-ended output
Per amplifier, RL, dm = 20 Ω, f = 10 MHz
∆VOUT, cm/∆VOUT, dm; ∆VOUT, dm = 1 V
−VS + 1.2 to +VS − 1.2
±65
−60
Input Bias Current
Input Resistance
Typ
−18
TMIN to TMAX variation
Differential
Common mode
Rev. A | Page 5 of 28
4
mV
μV/°C
μA
μA/°C
MΩ
MΩ
pF
V
dB
V
mA
dB
ADA4938-1/ADA4938-2
VOCM to ±OUT Performance
Table 4.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
Input Voltage Noise (RTI)
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
POWER DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Bias Current
Enabled
Disabled
Conditions
Min
VIN = 1.6 V to 3.4 V, 25% to 75%
VOS, cm = VOUT, cm; VDIN+ = VDIN– = VOCM = 2.5 V
∆VOUT, dm/∆VOCM; ∆VOCM = ±1 V
∆VOUT, cm/∆VOCM; ∆VOCM = ±1 V
0.95
Typ
Unit
400
1700
7.5
MHz
V/μs
nV/√Hz
−VS + 1.3 to +VS − 1.3
10
3
0.5
−89
1.00
V
kΩ
mV
μA
dB
V/V
4.5
34
40
1.0
−80
TMIN to TMAX variation
Powered down
∆VOUT, dm/∆VS; ∆VS = ±1 V
Max
1.05
11
36.5
1.7
V
mA
μA/°C
mA
dB
Powered down
Enabled
≤2.5
≥3
1
200
V
V
μs
ns
PD = 5 V
PD = 0 V
1
−260
μA
μA
OPERATING TEMPERATURE RANGE
−40
Rev. A | Page 6 of 28
+85
°C
ADA4938-1/ADA4938-2
ABSOLUTE MAXIMUM RATINGS
Parameter
Supply Voltage
Power Dissipation
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
Rating
12 V
See Figure 4
−65°C to +125°C
−40°C to +85°C
300°C
150°C
Stresses above those listed under Absolute Maximum Rating
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for the device (including exposed pad) soldered
to a high thermal conductivity 4-layer circuit board, as described in
EIA/JESD 51-7. The exposed pad is not electrically connected to
the device. It is typically soldered to a pad on the PCB that is
thermally and electrically connected to an internal ground plane.
Table 6. Thermal Resistance
Package Type
16-Lead LFCSP (Exposed Pad)
24-Lead LFCSP (Exposed Pad)
θJA
95
65
Unit
°C/W
°C/W
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive. The quiescent power is the voltage
between the supply pins (VS) times the quiescent current (IS).
The power dissipated due to the load drive depends upon the
particular application. The power due to load drive is calculated
by multiplying the load current by the associated voltage drop
across the device. RMS voltages and currents must be used in
these calculations.
Airflow increases heat dissipation, which effectively reducing
θJA. In addition, more metal directly in contact with the package
leads/exposed pad from metal traces, through-holes, ground,
and power planes reduces the θJA.
Figure 4 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the ADA4938-1,
16-lead LFCSP (95°C/W) and the ADA4938-2, 24-lead LFCSP
(65°C/W) on a JEDEC standard 4-layer board.
3.5
MAXIMUM POWER DISSIPATION (W)
Table 5.
3.0
2.5
ADA4938-2
2.0
1.5
ADA4938-1
1.0
0.5
The maximum safe power dissipation in the ADA4938-x
packages is limited by the associated rise in junction temperature (TJ) on the die. At approximately 150°C, which is the glass
transition temperature, the plastic changes its properties. Even
temporarily exceeding this temperature limit can change the
stresses that the package exerts on the die, permanently shifting
the parametric performance of the ADA4938. Exceeding a junction
temperature of 150°C for an extended period can result in changes
in the silicon devices, potentially causing failure.
0
–40 –30 –20 –10
0
10
20
30
40
50
AMBIENT TEMPERATURE (°C)
60
70
80
90
06592-103
Maximum Power Dissipation
Figure 4. Maximum Power Dissipation vs. Temperature, 4-Layer Board
ESD CAUTION
Rev. A | Page 7 of 28
ADA4938-1/ADA4938-2
+IN1
–FB1
–VS1
–VS1
PD1
–OUT1
24
23
22
21
20
19
13 –VS
15 –VS
14 –VS
16 –VS
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
12 PD
11 –OUT
–IN 3
TOP VIEW
(Not to Scale)
10 +OUT
9 VOCM
1
2
3
4
5
6
ADA4938-2
TOP VIEW
(Not to Scale)
18
17
16
15
14
13
+OUT1
VOCM1
–VS2
–VS2
PD2
–OUT2
–IN2
+FB2
+VS2
+VS2
VOCM2
+OUT2
NOTES
1. THE EXPOSED PAD IS NOT ELECTRICALLY CONNECTED
TOTHE DEVICE. IT IS TYPICALLY SOLDERED TO GROUND
OR A POWER PLANE ON THE PCB THAT IS THERMALLY
CONDUCTIVE.
PIN 1
INDICATOR
7
8
9
10
11
12
+VS 8
+VS 5
+FB 4
+VS 7
ADA4938-1
+VS 6
+IN 2
–IN1
+FB1
+VS1
+VS1
–FB2
+IN2
NOTES
1. THE EXPOSED PAD IS NOT ELECTRICALLY CONNECTED
TOTHE DEVICE. IT IS TYPICALLY SOLDERED TO GROUND
OR A POWER PLANE ON THE PCB THAT IS THERMALLY
CONDUCTIVE.
Figure 6. ADA4938-2 Pin Configuration
Figure 5. ADA4938-1 Pin Configuration
Table 7. ADA4938-1 Pin Function Descriptions
Table 8. ADA4938-2 Pin Function Descriptions
Pin No.
1
2
3
4
5 to 8
9
10
11
12
13 to 16
EP
Pin No.
1
2
3, 4
5
6
7
8
9, 10
11
12
13
14
15, 16
17
18
19
20
21, 22
23
24
EP
Mnemonic
−FB
+IN
−IN
+FB
+VS
VOCM
+OUT
−OUT
PD
−VS
06592-206
PIN 1
INDICATOR
06592-003
–FB 1
Description
Negative Output Feedback Pin.
Positive Input Summing Node.
Negative Input Summing Node.
Positive Output Feedback Pin.
Positive Supply Voltage.
Output Common-Mode Voltage.
Positive Output for Load Connection.
Negative Output for Load Connection.
Power-Down Pin.
Negative Supply Voltage.
Exposed Paddle. The exposed pad is not
electrically connected to the device. It is
typically soldered to ground or a
power plane on the PCB that is
thermally conductive.
Rev. A | Page 8 of 28
Mnemonic
−IN1
+FB1
+VS1
−FB2
+IN2
−IN2
+FB2
+VS2
VOCM2
+OUT2
−OUT2
PD2
−VS2
VOCM1
+OUT1
−OUT1
PD1
−VS1
−FB1
+IN1
Description
Negative Input Summing Node 1.
Positive Output Feedback Pin 1.
Positive Supply Voltage 1.
Negative Output Feedback Pin 2.
Positive Input Summing Node 2.
Negative Input Summing Node 2.
Positive Output Feedback Pin 2.
Positive Supply Voltage 2.
Output Common-Mode Voltage 2.
Positive Output 2.
Negative Output 2.
Power-Down Pin 2.
Negative Supply Voltage 2.
Output Common-Mode Voltage 1.
Positive Output 1.
Negative Output 1.
Power-Down Pin 1.
Negative Supply Voltage 1.
Negative Output Feedback Pin 1.
Positive Input Summing Node 1.
Exposed Paddle. The exposed pad is
not electrically connected to the
device. It is typically soldered to
ground or a power plane on the PCB
that is thermally conductive.
ADA4938-1/ADA4938-2
TYPICAL PERFORMANCE CHARACTERISTICS
3
0
0
–3
–6
–9
G
G
G
G
–12
10
100
1000
FREQUENCY (MHz)
= +1
= +2
= +3.16
= +5
1
10
100
1000
FREQUENCY (MHz)
Figure 10. Large Signal Frequency Response for Various Gains
3
0
0
–3
–3
GAIN (dB)
3
–6
–6
–9
VS = +5V
VS = ±5V
1
10
100
1000
FREQUENCY (MHz)
–12
06592-106
–12
VS = +5V
VS = ±5V
1
10
100
1000
FREQUENCY (MHz)
Figure 8. Small Signal Response for Various Supplies, VOUT = 0.1 V p-p
06592-109
–9
Figure 11. Large Signal Response for Various Supplies
3
0
0
NORMALIZED GAIN (dB)
3
–3
–6
–3
–6
–9
–40°C
+25°C
+85°C
–12
1
10
100
FREQUENCY (MHz)
Figure 9. Small Signal Frequency Response for
Various Temperatures, VOUT = 0.1 V p-p
1000
–40°C
+25°C
+85°C
–12
1
10
100
FREQUENCY (MHz)
1000
06592-110
–9
06592-107
NORMALIZED GAIN (dB)
G
G
G
G
–12
Figure 7. Small Signal Frequency Response for Various Gains, VOUT = 0.1 V p-p
GAIN (dB)
–6
–9
= +1
= +2
= +3.16
= +5
1
–3
06592-108
NORMALIZED GAIN (dB)
3
06592-105
NORMALIZED GAIN (dB)
TA = 25°C, +VS = 5 V, −VS = −5 V, VOCM = 0 V, RT = 61.9 Ω, RG = RF = 200 Ω, G = +1, RL, dm = 1 kΩ, unless otherwise noted.
All measurements were performed with single-ended input and differential output, unless otherwise noted. For gains other than G = +1,
values for RF and RG are shown in Table 11.
Figure 12. Large Signal Frequency Response for Various Temperatures
Rev. A | Page 9 of 28
3
0
0
–3
–3
–6
–9
–12
–15
RL = 1kΩ
RL = 100Ω
RL = 200Ω
1
10
100
1000
1
0
NORMALIZED GAIN (dB)
0
–3
–6
1
10
100
1000
FREQUENCY (MHz)
Figure 14. Small Signal Frequency Response for
Various Gains, VS = 5 V, VOUT = 0.1 V p-p
–6
NORMALIZED GAIN (dB)
0
–3
–6
= +1
= +2
= +3.16
= +5
FREQUENCY (MHz)
1000
–3
–6
G
G
G
G
–12
06592-113
100
1000
0
–9
10
100
Figure 17. Large Signal Frequency Response for Various Gains, VS = 5 V
3
1
10
FREQUENCY (MHz)
3
–12
= +1
= +2
= +3.16
= +5
1
6
G
G
G
G
G
G
G
G
–12
6
–9
1000
–3
–9
= +1
= +2
= +3.16
= +5
06592-112
–12
100
Figure 16. Large Signal Frequency Response for Various Loads
3
G
G
G
G
10
FREQUENCY (MHz)
3
–9
RL = 1kΩ
RL = 100Ω
RL = 200Ω
–21
Figure 13. Small Signal Frequency Response for
Various Loads, VOUT = 0.1 V p-p
NORMALIZED GAIN (dB)
–15
–18
FREQUENCY (MHz)
NORMALIZED GAIN (dB)
–12
06592-115
–21
–9
1
= +1
= +2
= +3.16
= +5
10
100
1000
FREQUENCY (MHz)
Figure 15. Small Signal Response for Various Gains, RF = 402 Ω, VOUT = 0.1 V p-p
Rev. A | Page 10 of 28
Figure 18. Large Signal Response for Various Gains, RF = 402 Ω
06592-116
–18
–6
06592-114
NORMALIZED GAIN (dB)
3
06592-111
NORMALIZED GAIN (dB)
ADA4938-1/ADA4938-2
6
3
3
0
–3
–6
G
G
G
G
–9
–12
= +1
= +2
= +3.16
= +5
1
–3
–6
G
G
G
G
–9
10
100
1000
FREQUENCY (MHz)
–12
10
100
1000
FREQUENCY (MHz)
Figure 22. Large Signal Frequency Response for Various Gains, RF = 402 Ω,
VS = 5 V
3
0
0
–3
–3
GAIN (dB)
3
–6
–6
–9
VS = +5V
VS = ±5V
10
100
1000
FREQUENCY (MHz)
1
GAIN (dB)
100
1000
FREQUENCY (MHz)
06592-119
10
1000
Figure 23. VOUT, cm Large Signal Frequency Response
RL, dm = 1kΩ
RL, dm = 100Ω
RL, dm = 200Ω
1
100
FREQUENCY (MHz)
Figure 20. VOUT, cm Small Signal Frequency Response, VOUT = 0.1 V p-p
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
–0.1
–0.2
–0.3
–0.4
–0.5
–0.6
–0.7
–0.8
–0.9
–1.0
10
Figure 21. 0.1 dB Flatness Response for Various Loads, ADA4938-1,
VOUT = 0.1 V p-p
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
–0.1
–0.2
–0.3
–0.4
–0.5
RL, dm = 1kΩ
RL, dm = 100Ω
RL, dm = 200Ω
1
10
100
1000
FREQUENCY (MHz)
Figure 24. 0.1 dB Flatness Response for Various Loads, ADA4938-2,
VOUT = 0.1 V p-p
Rev. A | Page 11 of 28
06592-122
1
VS = +5V
VS = ±5V
–12
06592-118
–12
06592-121
–9
NORMALIZED GAIN (dB)
= +1
= +2
= +3.16
= +5
1
Figure 19. Small Signal Frequency Response for Various Gains, RF = 402 Ω,
VS = 5 V, VOUT = 0.1 V p-p
GAIN (dB)
0
06592-120
NORMALIZED GAIN (dB)
6
06592-117
NORMALIZED GAIN (dB)
ADA4938-1/ADA4938-2
ADA4938-1/ADA4938-2
–40
–40
–50
–60
–70
–80
–90
–90
–110
–110
–120
06592-123
10
100
FREQUENCY (MHz)
0
–60
–70
–60
–90
–100
4
5
6
7
8
9
RL
RL
RL
RL
RL
RL
= 1kΩ
= 1kΩ
= 200Ω
= 200Ω
= 100Ω
= 100Ω
–70
–80
–90
–100
–110
–110
–120
10
100
–120
FREQUENCY (MHz)
1
100
FREQUENCY (MHz)
Figure 26. Harmonic Distortion vs. Frequency and Gain
Figure 29. Harmonic Distortion vs. Frequency for Various Loads
–40
HD2,
HD3,
HD2,
HD3,
10
06592-127
1
06592-124
–130
–40
10MHz
10MHz
70MHz
70MHz
HD2,
HD3,
HD2,
HD3,
–50
10MHz
10MHz
70MHz
70MHz
–60
DISTORTION (dBc)
–70
–80
–90
–100
–70
–80
–90
–100
–110
–110
–130
–3.3 –2.7 –2.1 –1.5 –0.9 –0.3
0.3
0.9
1.5
2.1
2.7
VOCM (V)
3.3
06592-128
–120
–120
1.7
1.9
2.1
2.3
2.5
2.7
2.9
3.1
3.3
VOCM (V)
Figure 30. Harmonic Distortion vs. VOCM and Frequency, VS = 5 V
Figure 27. Harmonic Distortion vs. VOCM and Frequency
Rev. A | Page 12 of 28
06592-125
–60
HD2,
HD3,
HD2,
HD3,
HD2,
HD3,
–50
–80
–50
3
–40
= +1
= +1
= +2
= +2
= +5
= +5
DISTORTION (dBc)
–50
G
G
G
G
G
G
2
Figure 28. Harmonic Distortion vs. VOUT and Supply Voltage
–40
HD2,
HD3,
HD2,
HD3,
HD2,
HD3,
1
VOUT, dm (V)
Figure 25. Harmonic Distortion vs. Frequency and Supply Voltage
DISTORTION (dBc)
–80
–100
–120
DISTORTION (dBc)
–70
–100
1
HD2, +5V
HD3, +5V
HD2, ±5V
HD3, ±5V
–50
DISTORTION (dBc)
DISTORTION (dBc)
–60
VS = +5V
VS = +5V
VS = ±5V
VS = ±5V
06592-126
HD2,
HD3,
HD2,
HD3,
ADA4938-1/ADA4938-2
0
–10
–30
PSRR (dB)
DISTORTION (dBc)
–20
–40
–50
–60
–70
–80
–90
–110
29.5
29.6
29.7
29.8
29.9
30.0
30.1
30.2
30.3
30.4
30.5
FREQUENCY (MHz)
06592-129
–100
0
–5
–10
–15
–20
–25
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
0.1
–PSRR
+PSRR
1
10
100
1000
FREQUENCY (MHz)
Figure 31. Intermodulation Distortion
06592-132
10
Figure 34. PSRR vs. Frequency
–20
0
–25
–5
–30
–10
–35
–15
RETURN LOSS (dB)
–45
–50
–55
VS = ±5V
–60
–65
–25
S22
–30
–35
–40
VS = +5V
–70
–20
S11
–45
–75
1
10
100
1000
FREQUENCY (MHz)
–55
06592-130
–85
0.1
1
100
1000
FREQUENCY (MHz)
Figure 32. VIN CMRR vs. Frequency
Figure 35. Return Loss (S11, S22) vs. Frequency
–15
–40
RL = 1kΩ
RL = 200Ω
RL = 100Ω
RL = 200Ω
–20
–50
–25
–60
–30
SFDR (dBc)
–35
–40
–45
–70
–80
–90
–50
–100
–55
–110
–60
–65
1
10
100
FREQUENCY (MHz)
1000
06592-131
OUTPUT BALANCE (dB)
10
06592-134
–50
–80
Figure 33. Output Balance vs. Frequency
–120
1
10
100
FREQUENCY (MHz)
Figure 36. SFDR vs. Frequency for Various Loads
Rev. A | Page 13 of 28
06592-135
VIN CMRR (dB)
–40
ADA4938-1/ADA4938-2
26
100
24
INPUT VOLTAGE NOISE (nV/ Hz)
G = +1
NOISE FIGURE (dB)
22
20
G = +2
18
G = +4
16
14
10
100
500
FREQUENCY (MHz)
1
10
06592-136
10
10
10k
100k
1M
10M
100M
Figure 40. Input Voltage Noise vs. Frequency
10
4.0
8
3.5
6
3.0
4
PD INPUT
VOLTAGE (V)
2.5
2
0
–2
2.0
1.5
1.0
–4
NEGATIVE OUTPUT
0.5
–6
0
5
10
15
20
25
30
35
40
45
50
55
60
TIME (5ns/DIV)
–0.5
06592-137
–10
06592-140
0
VIN × 3.16
VOUT, dm
–8
TIME (200ns/DIV)
Figure 41. Power-Down Response Time
Figure 38. Overdrive Recovery Time (Pulse Input)
45
12
10
40
8
+85°C
+25°C
–40°C
35
6
CURRENT (mA)
4
VOLTAGE (V)
1k
FREQUENCY (Hz)
Figure 37. Noise Figure vs. Frequency
VOLTAGE (V)
100
06592-039
12
2
0
–2
–4
–6
30
25
20
15
10
–8
0
50
100
150
200
250
300
TIME (50ns/DIV)
350
400
450
500
0
2.0
06592-138
–12
Figure 39. Overdrive Amplitude Characteristics (Triangle Wave Input)
2.2
2.4
2.6
2.8
3.0
3.2
VOLTAGE (V)
3.4
3.6
3.8
4.0
06592-141
5
VIN × 3.16
VOUT, dm
–10
Figure 42. Supply Current vs. Power-Down Voltage and Temperature
Rev. A | Page 14 of 28
ADA4938-1/ADA4938-2
0.20
3.0
2.5
0.15
2.0
0.10
1.5
VOLTAGE (V)
VOLTAGE (V)
1.0
0.05
0
–0.05
0.5
0
–0.5
–1.0
–0.10
–1.5
–2.0
–0.15
–3.0
TIME (1ns/DIV)
Figure 46. Large Signal Transient Response
2.5
0.08
2.0
0.06
1.5
0.04
1.0
VOLTAGE (V)
0.10
0.02
0
–0.02
0.5
0
–0.5
–0.04
–1.0
–0.06
–1.5
–0.08
–2.0
06592-043
–0.10
TIME (2ns/DIV)
–2.5
TIME (2ns/DIV)
Figure 44. VOCM Small Signal Transient Response, VOUT = 0.1 V p-p
Figure 47. VOCM Large Signal Transient Response
60
40
30
20
–3
VOCM = –3.7V
VOCM = –3.5V
VOCM = –3V
VOCM = 0V
VOCM = +3V
VOCM = +3.5V
VOCM = +3.7V
–6
–9
10
2.2
2.4
2.6
2.8
3.0
3.2
VOLTAGE (V)
3.4
3.6
3.8
4.0
–12
06592-144
0
2.0
ALL CURVES ARE
NORMALIZED TO VOCM = 0V
0
CLOSED-LOOP GAIN (dB)
CURRENT (mA)
50
3
+85°C
+25°C
–40°C
Figure 45. Supply Current vs. Power-Down Voltage and Temperature, VS = 5 V
1
10
100
FREQUENCY (MHz)
1000
06592-048
VOLTAGE (V)
Figure 43. Small Signal Transient Response, VOUT = 0.1 V p-p
06592-046
TIME (1ns/DIV)
06592-145
06592-142
–2.5
–0.20
Figure 48. VOUT, dm Small Signal Frequency Response for Various VOCM,
VOUT = 0.1 V p-p
Rev. A | Page 15 of 28
ADA4938-1/ADA4938-2
–40
55
–50
–60
50
CROSSTALK (dB)
INPUT1, OUTPUT2
IP3 (dBm)
IP3 100Ω
45
40
–70
–80
–90
–100
INPUT2, OUTPUT1
–110
–120
06592-049
35
–140
0.3
100
FREQUENCY (MHz)
10
100
1000
FREQUENCY (MHz)
Figure 49. IP3 vs. Frequency
3
1
06592-888
30
10
–130
Figure 52. Crosstalk vs. Frequency for ADA4938-2
2
ALL CURVES ARE
NORMALIZED TO VOCM = 0V
1.0
VIN
0
0.1
0
–0.1
–12
1
–1
10
100
1000
FREQUENCY (MHz)
Figure 50. VOUT, dm Large Signal Frequency Response for Various VOCM
100
1
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
100M
06592-051
10
Figure 51. Input Current Noise vs. Frequency
Rev. A | Page 16 of 28
SETTLING ERROR
–2
–0.5
–1.0
TIME (1ns/DIV)
Figure 53. 0.1% Settling Time
06592-153
VIN (V)
VOCM = –3.7V
VOCM = –3.5V
VOCM = –3V
VOCM = 0V
VOCM = +3V
VOCM = +3.5V
VOCM = +3.7V
SETTLING ERROR (%)
0.5
–6
–9
INPUT CURRENT NOISE (pA/ Hz)
1
–3
06592-50
CLOSED-LOOP GAIN (dB)
0
ADA4938-1/ADA4938-2
TEST CIRCUTS
200Ω
+5V
50Ω
200Ω
VIN
VOCM
61.9Ω
ADA4938
1kΩ
200Ω
06592-246
27.5Ω
–5V
200Ω
Figure 54. Equivalent Basic Test Circuit
200Ω
+5V
50Ω
200Ω
VIN
50Ω
VOCM
61.9Ω
ADA4938
200Ω
50Ω
06592-247
27.5Ω
–5V
200Ω
Figure 55. Test Circuit for Output Balance
200Ω
+5V
50Ω
0.1µF
200Ω
412Ω
FILTER
61.9Ω
VOCM
ADA4938
0.1µF
200Ω
412Ω
27.5Ω
–5V
200Ω
Figure 56. Test Circuit for Distortion Measurements
Rev. A | Page 17 of 28
06592-248
VIN
FILTER
ADA4938-1/ADA4938-2
TERMINOLOGY
–FB
RG
RF
Common-Mode Voltage
The common-mode voltage is the average of two node voltages.
The output common-mode voltage is defined as
ADA4938
+IN
–OUT
VOCM
RL, dm VOUT, dm
RF
–IN
+OUT
+FB
VOUT, cm = (V+OUT + V−OUT)/2
06592-004
RG
Figure 57. Circuit Definitions
Differential Voltage
The differential voltage is the difference between two node
voltages. For example, the output differential voltage (or
equivalently, output differential-mode voltage) is defined as
VOUT, dm = (V+OUT − V−OUT)
where V+OUT and V−OUT refer to the voltages at the +OUT and
−OUT terminals with respect to a common reference.
Balance
Balance is a measure of how well differential signals are matched in
amplitude and are exactly 180° apart in phase. Balance is most
easily determined by placing a well-matched resistor divider
between the differential voltage nodes and comparing the
magnitude of the signal at the midpoint of the divider with
the magnitude of the differential signal. By this definition,
output balance is the magnitude of the output common-mode
voltage divided by the magnitude of the output differential
mode voltage.
Output Balance Error =
Rev. A | Page 18 of 28
VOUT , cm
VOUT , dm
ADA4938-1/ADA4938-2
THEORY OF OPERATION
The ADA4938-x differs from conventional op amps in that it
has two outputs whose voltages move in opposite directions.
Like an op amp, it relies on open-loop gain and negative
feedback to force these outputs to the desired voltages. The
ADA4938-x behaves much like a standard voltage feedback op
amp and makes it easier to perform single-ended-to-differential
conversions, common-mode level shifting, and amplifications of
differential signals. Also like an op amp, the ADA4938-x has
high input impedance and low output impedance.
Two feedback loops are employed to control the differential and
common-mode output voltages. The differential feedback, set
with external resistors, controls only the differential output
voltage. The common-mode feedback controls only the commonmode output voltage. This architecture makes it easy to set the
output common-mode level to any arbitrary value. It is forced,
by internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
The ADA4938-x architecture results in outputs that are highly
balanced over a wide frequency range without requiring tightly
matched external components. The common-mode feedback
loop forces the signal component of the output commonmode voltage to zero, which results in nearly perfectly balanced
differential outputs that are identical in amplitude and are
exactly 180° apart in phase.
SETTING THE CLOSED-LOOP GAIN
The differential-mode gain of the circuit in Figure 57 can be
determined by
VOUT , dm
VIN , dm
=
RF
RG
This assumes the input resistors (RG) and feedback resistors (RF)
on each side are equal.
ESTIMATING THE OUTPUT NOISE VOLTAGE
The differential output noise of the ADA4938 can be estimated
using the noise model in Figure 58. The input-referred noise
voltage density, vnIN, is modeled as a differential input, and the
noise currents, inIN− and inIN+, appear between each input and
ground. The noise currents are assumed to be equal and produce a
voltage across the parallel combination of the gain and feedback
resistances. vn, cm is the noise voltage density at the VOCM pin.
Each of the four resistors contributes (4kTR)1/2. Table 9 summarizes
the input noise sources, the multiplication factors, and the outputreferred noise density terms.
VnRG1
RG1
VnRF1
RF1
inIN+
+
inIN–
VnIN
ADA4938
VnOD
ANALYZING AN APPLICATION CIRCUIT
VOCM
VnRG2
RG2
RF2
VnCM
VnRF2
06592-005
The ADA4938-x uses open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and −IN (see
Figure 57). For most purposes, this voltage can be assumed
to be zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
Figure 58. ADA4938 Noise Model
Table 9. Output Noise Voltage Density Calculations
Input Noise Contribution
Differential Input
Inverting Input
Noninverting Input
VOCM Input
Gain Resistor, RG1
Gain Resistor, RG2
Feedback Resistor, RF1
Feedback Resistor, RF2
Input Noise Term
vnIN
inIN−
inIN+
vn, cm
vnRG1
vnRG2
vnRF1
vnRF2
Input Noise
Voltage Density
vnIN
inIN− × (RG2||RF2)
inIN+ × (RG1||RF1)
vn, cm
(4kTRG1)1/2
(4kTRG2)1/2
(4kTRF1)1/2
(4kTRF2)1/2
Rev. A | Page 19 of 28
Output
Multiplication Factor
GN
GN
GN
GN(β1 − β2)
GN(1 − β1)
GN(1 − β2)
1
1
Output Noise
Voltage Density Term
vnO1 = GN(vnIN)
vnO2 = GN[inIN− × (RG2||RF2)]
vnO3 = GN[inIN+ × (RG1||RF1)]
vnO4 = GN(β1 − β2)(vnCM)
vnO5 = GN(1 − β1)(4kTRG1)1/2
vnO6 = GN(1 − β2)(4kTRG2)1/2
vnO7 = (4kTRF1)1/2
vnO8 = (4kTRF2)1/2
ADA4938-1/ADA4938-2
Similar to the case of a conventional op amp, the output noise
voltage densities can be estimated by multiplying the inputreferred terms at +IN and −IN by the appropriate output factor,
where:
2
GN =
is the circuit noise gain.
(β1 + β2 )
RG1
RG2
β1 =
and β2 =
are the feedback factors.
RF1 + RG1
RF2 + RG2
CALCULATING THE INPUT IMPEDANCE OF AN
APPLICATION CIRCUIT
The effective input impedance of a circuit depends on whether
the amplifier is being driven by a single-ended or differential
signal source. For balanced differential input signals, as shown
in Figure 59, the input impedance (RIN, dm) between the inputs
(+DIN and −DIN) is simply RIN, dm = 2 × RG.
RF
ADA4938
When RF1/RG1 = RF2/RG2, β1 = β2 = β, and the noise gain
becomes
+DIN
1
R
=1+ F
β
RG
VOCM
–DIN
RG
Note that the output noise from VOCM goes to zero in this case.
The total differential output noise density, vnOD, is the root-sumsquare of the individual output noise terms.
VOUT, dm
–IN
RF
Figure 59. ADA4938 Configured for Balanced (Differential) Inputs
For an unbalanced, single-ended input signal (see Figure 60),
the input impedance is
8
2
∑ vnOi
i =1
THE IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
RIN , cm
As previously mentioned, even if the external feedback networks
(RF/RG) are mismatched, the internal common-mode feedback
loop still forces the outputs to remain balanced. The amplitudes
of the signals at each output remain equal and 180° out of phase.
The input-to-output, differential mode gain varies proportionately
to the feedback mismatch, but the output balance is unaffected.
As well as causing a noise contribution from VOCM, ratio matching
errors in the external resistors result in a degradation of the
ability of the circuit to reject input common-mode signals, much
the same as for a four-resistor difference amplifier made from a
conventional op amp.
In addition, if the dc levels of the input and output commonmode voltages are different, matching errors result in a small
differential-mode output offset voltage. When G = +1, with a
ground referenced input signal and the output common-mode
level set to 2.5 V, an output offset of as much as 25 mV (1% of
the difference in common-mode levels) can result if 1% tolerance
resistors are used. Resistors of 1% tolerance result in a worst-case
input CMRR of about 40 dB, a worst-case differential-mode
output offset of 25 mV due to 2.5 V level-shift, and no significant
degradation in output balance error.
⎛
⎞
⎜
⎟
R
G
⎟
=⎜
RF
⎜1−
⎟
⎜
⎟
(
)
2
R
R
×
+
F ⎠
G
⎝
RF
+VS
RG
RS
VOCM
RT
ADA4938
VOUT, dm
RG
RS
RT
RF
06592-007
v nOD =
+IN
06592-006
GN =
+VS
RG
Figure 60. ADA4938-x Configured for Unbalanced (Single-Ended) Input
The input impedance of the circuit is effectively higher than it
would be for a conventional op amp connected as an inverter
because a fraction of the differential output voltage appears at
the inputs as a common-mode signal, partially bootstrapping
the voltage across the Input Gain Resistor RG.
INPUT COMMON-MODE VOLTAGE RANGE IN
SINGLE-SUPPLY APPLICATIONS
The ADA4938 is optimized for level-shifting, ground-referenced
input signals. As such, the center of the input common-mode
range is shifted approximately 1 V down from midsupply. The
input common-mode range at the summing nodes of the amplifier
is from 0.3 V above −VS to 1.6 V below +VS. To avoid clipping at
the outputs, the voltage swing at the +IN and −IN terminals must
be confined to these ranges.
Rev. A | Page 20 of 28
ADA4938-1/ADA4938-2
RF
TERMINATING A SINGLE-ENDED INPUT
200Ω
+VS
Using an example with an input source of 2 V, a source
resistance of 50 Ω, and an overall gain of 1 V/V, four simple
steps must be followed to terminate a single-ended input to the
ADA4938-x.
RTH
RG
27.4Ω
200Ω
VTH
1.1V
VOCM
1. The input impedance is calculated using the formula
RF
RTS
27.4Ω
+VS
50Ω
200Ω
VOCM
ADA4938
RL
VO
To make the output voltage VO = 1 V, RF is calculated
using
⎛ V × (RG + RTS ) ⎞ ⎛ 1× (200 + 27.4) ⎞
⎟=⎜
RF = ⎜⎜ O
⎟ = 207 Ω
⎟ ⎝
VTH
1.1
⎠
⎝
⎠
RG
200Ω
200Ω
To return the overall gain to 1 V/V (VO = VS = 2 V), RF
should be
b.
06592-081
–VS
RF
⎛ V × (RG + RTS ) ⎞ ⎛ 2 × (200 + 27.4) ⎞
⎟=⎜
RF = ⎜⎜ O
⎟ = 414 Ω
⎟ ⎝
VTH
1.1
⎠
⎝
⎠
Figure 61. Single-Ended Input Impedance
2. To provide a 50 Ω termination for the source, the Resistor RT
is calculated such that RT || RIN = 50 Ω, or RT = 61.9 Ω.
RF
RF
+VS
200Ω
+VS
50Ω
RS
RS
50Ω
RG
50Ω
RT
61.9Ω
VS
2V
VS
2V
200Ω
VOCM
ADA4938
RL
RTS
27.4Ω
VOCM
ADA4938
RL
–VS
06592-082
RF
200Ω
3. To compensate for the imbalance of the gain resistors, a correction resistor (RTS) is added in series with the inverting Input
Gain Resistor RG. RTS is equal to the Thevenin equivalent of
the source resistance (RS||RT).
RTH
The VOCM pin of the ADA4938-x is internally biased at a voltage
approximately equal to the midsupply point (average value of
the voltages on V+ and V−). Relying on this internal bias results
in an output common-mode voltage that is within about 100 mV of
the expected value.
In cases where more accurate control of the output commonmode level is required, it is recommended that an external
source or resistor divider (10 kΩ or greater resistors) be used.
06592-083
27.4Ω
VTH
1.1V
Figure 65. Complete Single-Ended-to-Differential System
SETTING THE OUTPUT COMMON-MODE VOLTAGE
Figure 62. Adding Termination Resistor RT
RS
VO
200Ω
RF
–VS
VS
2V
200Ω
RG
200Ω
RT
61.9Ω
RG
RT
61.9Ω
VO
RG
50Ω
06592-084
200Ω
Figure 64. Balancing Gain Resistor RG
a.
RG
VS
2V
–VS
RF
4. Finally, the feedback resistor is recalculated to adjust the
output voltage to the desired level.
200Ω
RS
200Ω
06592-085
RIN
267Ω
VO
RL 0.97V
RG
⎛
⎞ ⎛
⎞
⎜
⎟ ⎜
⎟
R
200
G
⎜
⎟
⎟ = 267 Ω
⎜
=
=
200
RF
⎜
⎟ ⎜
⎟
⎜ 1 − 2 × (R + R ) ⎟ ⎜ 1 − 2 × (200 + 200) ⎟
⎠
F ⎠ ⎝
G
⎝
R IN
ADA4938
Figure 63. Calculating Thevenin Equivalent
RTS = RTH = RS || RT = 27.4 Ω. Note that VTH is not equal to
VS/2, which would be the case if the amplifier circuit did
not affect the termination.
It is also possible to connect the VOCM input to a common-mode
level (CML) output of an ADC. However, care must be taken to
ensure that the output has sufficient drive capability. The input
impedance of the VOCM pin is approximately 10 kΩ. If multiple
ADA4938-x devices share one reference output, it is recommended
that a buffer be used.
Rev. A | Page 21 of 28
ADA4938-1/ADA4938-2
Table 10 and Table 11 list several common gain settings, associated
resistor values, input impedances, and output noise densities for
both balanced and unbalanced input configurations. Also shown
are the input common-mode voltages under the given conditions
for different VOCM settings for both a 10 V single supply and
±5 V dual supplies.
Table 10. Differential Ground-Referenced Input, DC-Coupled; See Figure 59
Nominal
Gain (V/V)
1
2
3.16
5
RF (Ω)
200
402
402
402
RG (Ω)
200
200
127
80.6
RIN, dm (Ω)
400
400
254
161
Differential
Output
Noise Density
(nV/√Hz)
6.5
10.4
13.4
18.2
Common-Mode Level at +IN, −IN (V)
+VS = 5 V, −VS = −5 V
+VS = 10 V, −VS = 0 V
VOUT, dm = 2.0 V p-p
VOUT, dm = 2.0 V p-p
VOCM = 2.5 V
VOCM = 3.5 V
VOCM = 1.0 V
VOCM = 3.2 V
1.25
1.75
0.50
1.60
0.83
1.16
0.33
1.06
0.60
0.84
0.24
0.77
0.42
0.58
0.17
0.53
Table 11. Single-Ended Ground-Referenced Input, DC-Coupled, RS = 50 Ω; See Figure 60
Nominal
Gain (V/V)
1
2
3.16
5
1
2
RF (Ω)
200
402
402
402
RG1 (Ω)
200
200
127
80.6
RT (Ω)
60.4
60.4
66.5
76.8
RIN,se (Ω)
267
300
205
138
RG2 (Ω) 1
226
226
158
110
Overall
Gain (V/V) 2
0.9
1.8
2.5
3.6
Differential
Output
Noise
Density
(nV/√Hz)
6.2
9.8
11.8
14.7
RG2 = RG1 + RTS.
Includes effects of termination match.
Rev. A | Page 22 of 28
Common-Mode Swing at +IN, −IN (V)
+VS = 10 V, −VS = 0 V
VOUT, dm = 2.0 V p-p
VOCM = 2.5 V
VOCM = 3.5 V
1.00 to 1.50
1.50 to 2.00
0.66 to 1.00
1.00 to 1.33
0.48 to 0.72
0.72 to 0.96
0.33 to 0.50
0.50 to 0.67
+VS = 5 V, −VS = −5 V
VOUT, dm = 2.0 V p-p
VOCM = 0 V
VOCM = 2.0 V
−0.25 to +0.25
0.75 to 1.25
−0.17 to +0.17
0.50 to 0.83
−0.12 to +0.12
0.36 to 0.60
−0.08 to +0.08
0.25 to 0.42
ADA4938-1/ADA4938-2
LAYOUT, GROUNDING, AND BYPASSING
As a high speed device, the ADA4938-x is sensitive to the
PCB environment in which it operates. Realizing its superior
performance requires attention to the details of high speed
PCB design.
Bypass the power supply pins as close to the device as possible
and directly to a nearby ground plane. Use high frequency ceramic
chip capacitors. It is recommended that two parallel bypass capacitors (1000 pF and 0.1 μF) be used for each supply with the
1000 pF capacitor placed closer to the device; if further away,
provide low frequency bypassing using 10 μF tantalum capacitors
from each supply to ground.
The first requirement is a solid ground plane that covers as much of
the board area around the ADA4938-x as possible. However, the
area near the feedback resistors (RF), input gain resistors (RG),
and the input summing nodes should be cleared of all ground
and power planes (see Figure 66). Clearing the ground and
power planes minimizes any stray capacitance at these nodes
and prevents peaking of the response of the amplifier at high
frequencies.
Signal routing should be short and direct to avoid parasitic
effects. Wherever complementary signals exist, provide a
symmetrical layout to maximize balanced performance.
When routing differential signals over a long distance, keep
PCB traces close together and twist any differential wiring to
minimize loop area. Doing this reduces radiated energy and
makes the circuit less susceptible to interference.
The thermal resistance, θJA, is specified for the device, including
the exposed pad, soldered to a high thermal conductivity 4-layer
circuit board, as described in EIA/JESD 51-7. The exposed pad
is electrically isolated from the device; therefore, it can be connected to a ground plane using vias. Examples of the thermal
attach pad and via structure for the ADA4938-1 are shown in
Figure 67 and Figure 68.
1.30
0.80
06592-060
1.30 0.80
06592-008
Figure 67. Recommended PCB Thermal Attach Pad (ADA4938-1)
(Dimensions in mm)
Figure 66. Ground and Power Plane Voiding in Vicinity of RF and RG
1.30
TOP METAL
GROUND PLANE
0.30
PLATED
VIA HOLE
06592-061
POWER PLANE
BOTTOM METAL
Figure 68. Cross-Section of a 4-Layer PCB (ADA4938-1) Showing a Thermal Via Connection to the Buried Ground Plane (Dimensions in mm)
Rev. A | Page 23 of 28
ADA4938-1/ADA4938-2
HIGH PERFORMANCE ADC DRIVING
The circuit in Figure 70 shows a simplified front-end connection
for an ADA4938-x driving an AD9246, 14-bit, 125 MSPS ADC.
The AD9246 achieves its optimum performance when it is
driven differentially. The ADA4938-x eliminates the need for a
transformer to drive the ADC, performs a single-ended-todifferential conversion, buffers the driving signal, and provides
appropriate level shifting for dc coupling.
The ADA4938-x is ideally suited for dc-coupled baseband
applications. The circuit in Figure 69 shows a front-end connection
for an ADA4938-x driving an AD9446, 16-bit, 80 MSPS ADC.
The AD9446 achieves its optimum performance when it is
driven differentially. The ADA4938-x eliminates the need for a
transformer to drive the ADC, performs a single-ended-todifferential conversion, buffers the driving signal, and provides
appropriate level shifting for dc coupling.
The ADA4938-x is configured with dual ±5 V supplies and a
gain of ~2 V/V for a single-ended input to differential output.
The 76.8 Ω termination resistor, in parallel with the singleended input impedance of 137 Ω, provides a 50 Ω dc termination
for the source. The additional 30.1 Ω (120 Ω total) at the inverting
input balances the parallel dc impedance of the 50 Ω source and
the termination resistor driving the noninverting input.
The ADA4938-x is configured with a single 10 V supply and
unity gain for a single-ended input to differential output. The
61.9 Ω termination resistor, in parallel with the single-ended
input impedance of 267 Ω, provides a 50 Ω termination for the
source. The additional 26 Ω (226 Ω total) at the inverting input
balances the parallel impedance of the 50 Ω source and the
termination resistor driving the noninverting input.
The signal generator has a symmetric, ground-referenced
bipolar output. The VOCM pin of the ADA4938-x is connected to
the CML pin of the AD9246 to set the output common-mode
level at the appropriate point. A portion of this is fed back to the
summing nodes, biasing −IN and +IN at 0.55 V. For a commonmode voltage of 0.9 V, each ADA4938 output swings between
0.4 V and 1.4 V, providing a 2 V p-p differential output.
The signal generator has a symmetric, ground-referenced bipolar
output. The VOCM pin of the ADA4938-x is biased with an external
resistor divider to obtain the desired 3.5 V output common-mode.
One-half of the common-mode voltage is fed back to the summing
nodes, biasing −IN and +IN at 1.75 V. For a common-mode voltage of 3.5 V, each ADA4938-x output swings between 2.7 V
and 4.3 V, providing a 3.2 V p-p differential output.
The output is dc-coupled to a single-pole, low-pass filter. The filter
reduces the noise bandwidth of the amplifier and provides some
level of isolation from the switched capacitor inputs of the ADC.
The AD9246 is set for a 2 V p-p full-scale input by connecting the
SENSE pin to AGND. The inputs of the AD9246 are biased at
1 V by connecting the CML output, as shown in Figure 70.
The output of the amplifier is dc-coupled to the ADC through a
second-order, low-pass filter with a −3 dB frequency of 50 MHz.
The filter reduces the noise bandwidth of the amplifier and
isolates the driver outputs from the ADC inputs.
The AD9446 is configured for a 4.0 V p-p full-scale input by
setting R1 = R2 = 1 kΩ between the VREF pin and SENSE pin
in Figure 69.
10V
200Ω
5V (A) 3.3V (A) 3.3V (D)
10V
VOCM
61.9Ω
30nH
+
AVDD2 AVDD1 DRVDD
VIN+
BUFFER T/H
24.3Ω
ADA4938
47pF
ADC
24.3Ω
SIGNAL
GENERATOR
30nH
226Ω
AD9446
16
VIN–
CLOCK/
TIMING
200Ω
AGND
REF
SENSE
R1
VREF
06592-054
200Ω
50Ω
R2
Figure 69. ADA4938 Driving an AD9446, 16-Bit, 80 MSPS ADC
200Ω
50Ω
VIN
1.8V
+5V
76.8Ω
90Ω
VOCM
33Ω
+
ADA4938
DRVDD
AD9246
10pF
90Ω
VIN+
33Ω
D13 TO
D0
AGND SENSE CML
30.1Ω
–5V
06592-056
0.1µF
AVDD
VIN–
200Ω
Figure 70. ADA4938 Driving an AD9246, a 14-Bit, 125 MSPS ADC
Rev. A | Page 24 of 28
ADA4938-1/ADA4938-2
OUTLINE DIMENSIONS
3.00
BSC SQ
0.60 MAX
0.45
13
16
12 (BOTTOM VIEW) 1
2.75
BSC SQ
TOP
VIEW
EXPOSED
PAD
9
0.50
BSC
12° MAX
0.30
0.23
0.18
4
5
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
0.05 MAX
0.02 NOM
SEATING
PLANE
8
1.50 REF
0.80 MAX
0.65 TYP
1.00
0.85
0.80
PIN 1
INDICATOR
*1.45
1.30 SQ
1.15
0.20 REF
072208-A
PIN 1
INDICATOR
0.50
0.40
0.30
*COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2
EXCEPT FOR EXPOSED PAD DIMENSION.
Figure 71. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
3 mm × 3 mm Body
(CP-16-2)
Dimensions shown in millimeters
0.60 MAX
4.00
BSC SQ
TOP
VIEW
3.75
BSC SQ
0.50
BSC
1.00
0.85
0.80
12° MAX
0.30
0.23
0.18
SEATING
PLANE
24 1
19
18
2.25
2.10 SQ
1.95
EXPOSED
PAD
0.50
0.40
0.30
0.80 MAX
0.65 TYP
PIN 1
INDICATOR
(BOTTOM VIEW)
13
12
7
6
0.25 MIN
2.50 REF
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-2
072208-A
PIN 1
INDICATOR
0.60 MAX
Figure 72. 24-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad
(CP-24-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADA4938-1ACPZ-R2 1
ADA4938-1ACPZ-RL1
ADA4938-1ACPZ-R71
ADA4938-2ACPZ-R21
ADA4938-2ACPZ-RL1
ADA4938-2ACPZ-R71
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
24-Lead LFCSP_VQ
24-Lead LFCSP_VQ
24-Lead LFCSP_VQ
Z = RoHS Compliant Part.
Rev. A | Page 25 of 28
Package Option
CP-16-2
CP-16-2
CP-16-2
CP-24-1
CP-24-1
CP-24-1
Ordering Quantity
250
5,000
1,500
250
5,000
1,500
Branding
H11
H11
H11
ADA4938-1/ADA4938-2
NOTES
Rev. A | Page 26 of 28
ADA4938-1/ADA4938-2
NOTES
Rev. A | Page 27 of 28
ADA4938-1/ADA4938-2
NOTES
©2007–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06592-0-10/09(A)
Rev. A | Page 28 of 28