NCP1215 Product Preview Low Cost Variable OFF Time Switched Mode Power Supply Controller The NCP1215 is a controller for low power off-line flyback Switched Mode Power Supplies (SMPS) featuring low size, weight and cost constraints together with a good low standby power performance. The operating principle uses switching frequency reduction at light load by increasing the OFF Time. Also, when OFF Time expands, the peak current is gradually reduced down to approximately 1/4 of the maximum peak current to prevent from exciting the transformer mechanical resonances. The risk of acoustic noise is thus greatly diminished while keeping good standby power performance. A low power internal supply block also ensures very low current consumption at start-up without hampering the standby power performance. A special primary current sensing technique minimizes the impact of SMPS switching on control IC operation. The choice of peak voltage across the current sense resistor allows dissipation to be further reduced. The negative current sensing technique offers advantages over a traditional approach by avoiding the voltage drop incurred by traditional MOSFET source sensing. Thus, the IC drive capability is greatly improved. Finally, the bulk input ripple ensures a natural frequency dithering which smooths the EMI signature. http://onsemi.com MARKING DIAGRAMS 8 SO-8 D SUFFIX CASE 751 8 1 1 6 TSOP-6 (SOT23-6, SC59-6) SN SUFFIX CASE 318G 1 6 1 FAA A L Y W = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week SO-8 Variable OFF Time Control Method Very Low Current Consumption at Start-up Natural Frequency Dithering for Improved EMI Signature Current Mode Control Operation Peak Current Compression Reduces Transformer Noise Programmable Current Sense Resistor Peak Voltage Undervoltage Lockout FB 1 8 NC CT 2 7 NC CS 3 6 VCC 5 Gate GND 4 (Top View) TSOP-6 Typical Applications • • • • FAAYW PIN CONNECTIONS Features • • • • • • • P1215 ALYW CS 1 6 Gate GND 2 5 VCC CT 3 4 FB Auxiliary Power Supply Stand-by Power Supply AC/DC Adapter Off-line Battery Charger (Top View) ORDERING INFORMATION Device Package Shipping NCP1215DR2 SO-8 2500 Tape & Reel NCP1215SNT1 TSOP-6 3000 Tape & Reel This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice. Semiconductor Components Industries, LLC, 2003 May, 2003 - Rev. 0 1 Publication Order Number: NCP1215/D NCP1215 Line + + + - + FB NC CT NC CS Vcc GND Gate N Figure 1. Typical Application FB Feedback Loop Control VDD Iref Voffset + 0-7 V Ct − + Reference Regulator + − VCC 12/8.5 V Undervoltage Lockout Off-T ime Comparator 10 A Gate Driver Set CS Q 12.5-50 A Current Sense Comparator GND + − Reset Q Figure 2. Representative Block Diagram http://onsemi.com 2 Gate NCP1215 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PIN FUNCTION DESCRIPTION TSOP-6 SO-8 Symbol Description 4 1 FB The FB pin provides voltage feedback loop. The current injected into the pin determines the primary switch OFF time interval. It also influences the peak value of the primary current. 3 2 CT Connection for an external timing programming capacitor. 1 3 CS The CS pin senses the power switch current. 2 4 GND Primary and internal ground. 6 5 Gate Output drive for an external power MOSFET. 5 6 Vcc Power supply voltage and Undervoltage Lockout. 7 7 NC Unconnected pin. 8 8 NC Unconnected pin. ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁ MAXIMUM RATINGS Rating Symbol Value Unit Power Supply Voltage Vcc 18 V FB Pins Voltage Range VFB -0.3 to 18 V CS and CT Pin Voltage Range Vin -0.3 to 10 V RθJA 178 °C/W Tj 150 °C Tstg -60 to +150 °C VESD- HBM 2.0 kV Thermal Resistance, Junction-to-Air (SO-8 Version) Junction Temperature Storage Temperature Range ESD Voltage Protection, Human Body Model (Except Ct Pin) ESD Voltage Protection, Human Body Model for Ct Pin VESD- HBM- Ct 1.5 kV ESD Voltage Protection, Machine Model (Except Ct Pin) VESD- MM 200 V VESD- MM- Ct 150 V ESD Voltage Protection, Machine Model for Ct Pin http://onsemi.com 3 NCP1215 ELECTRICAL CHARACTERISTICS (VCC = 12 V, for typical values Tj = 25°C, for min/max values Tj = 0°C to +105°C, unless otherwise noted.) Characteristic Symbol Min Typ Max Unit Voffset 1.05 1.19 1.34 V Maximum CT Pin Voltage at FB Current = 25 A (Including Voffset) VCT- 25A 2.4 3.1 4.3 V Maximum CT Pin Voltage at FB Current = 50 A (Including Voffset) VCT- 50A 3.6 4.6 6.2 V ICT 8.0 9.8 11.5 A Source Current Maximum Voltage Capability VCT- max - 6.5 - V Minimum CT Pin Voltage (Pin Unloaded, Discharge Switch Turned On) VCT- min - - 20 mV Minimum Source Current (IFB = 180 A, CT Pin Grounded) ICS- min 8.0 12.5 16 A Maximum Source Current (IFB = 0 A, CT Pin Grounded) ICS- max 40 49 58 A Vth 15 42 80 mV tdelay - 215 310 ns Sink Resistance (Isink = 30 mA) ROL 25 40 90 Source Resistance (Isource = 30 mA) ROH 60 80 130 Vstart- up - 12.5 14.2 V VUVLO 7.2 9.0 - V Vhys 2.2 3.5 - V VCC Start-up Current Consumption (VCC = 8.0 V) ICC- start - 2.8 6.5 A VCC Steady State Current Consumption (CGATE = 1.0 nF, fSW = 100 kHz, FB open) ICC- SW 0.55 0.9 1.75 mA VOLTAGE FEEDBACK Offset Voltage CT PIN - OFF TIME CONTROL Source Current (CT Pin Grounded) CURRENT SENSE Comparator Threshold Voltage Propagation Delay (CS Falling Edge to Gate Output) GATE DRIVE POWER SUPPLY VCC Start-up Voltage Undervoltage Lockout Threshold Voltage Hysteresis (Vstart- up - VUVLO) http://onsemi.com 4 NCP1215 11.6 8.8 11.5 8.7 11.4 8.6 VUVLO, (V) Vstartup, (V) TYPICAL CHARACTERISTICS 11.3 8.5 11.2 8.4 11.1 8.3 11.0 -25 0 25 50 75 8.2 -25 125 100 0 25 50 75 100 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) Figure 3. Vstartup Threshold vs. Junction Temperature Figure 4. VUVLO Threshold vs. Junction Temperature 0.990 125 1.20 1.18 0.985 1.16 1.14 Voffset, (V) ICC- SW, (mA) 0.980 0.975 0.970 1.12 1.10 1.08 1.06 1.04 0.965 1.02 0.960 -25 0 25 50 75 100 1.00 -25 125 0 TJ, JUNCTION TEMPERATURE (°C) 48.5 60 48.0 55 VCS- th, (mV) ICS- max, (µA) 65 47.5 47.0 46.0 35 75 125 45 40 50 100 50 46.5 25 75 Figure 6. Offset Voltage vs. Junction Temperature 49.0 0 50 TJ, JUNCTION TEMPERATURE (°C) Figure 5. Operating Current Consumption vs. Junction Temperature 45.5 -25 25 100 30 -25 125 0 25 50 75 100 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) Figure 7. Current Sense Source Current vs. Junction Temperature Figure 8. Current Sense Threshold vs. Junction Temperature http://onsemi.com 5 125 NCP1215 16 10.0 9.9 14 VCT- min, (mV) ICT, (µA) 9.8 9.7 9.6 12 10 8 9.5 9.4 -25 0 25 50 75 100 6 -25 125 0 25 50 75 100 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) Figure 9. CT pin Source Current vs. Junction Temperature Figure 10. CT pin Threshold vs. Junction Temperature 120 60.0 100 50.0 125 Rsource 80 40.0 60 ICS, (µA) Rsource-R sink, () TJ = 25°C Rsink 30.0 40 20.0 20 10.0 0 -25 0 25 50 75 100 0.0 125 0 TJ, JUNCTION TEMPERATURE (°C) 25 50 75 100 Ifb, FEEDBACK CURRENT (µA) Figure 11. Drive Sink and Source Resistance vs. Junction Temperature Figure 12. Current Sense Source Current vs. Feedback Current http://onsemi.com 6 125 NCP1215 APPLICATION INFORMATION Feedback Loop Control The NCP1215 implements a current mode SMPS with a variable OFF-time dependant upon output power demand. It can be seen from the typical application that NCP1215 is designed to operate with a minimum number of external component. The NCP1215 incorporates the following features: • Frequency Foldback: Since the switch-off time increases when power demand decreases, the switching frequency naturally diminishes in light load conditions. This helps to minimize switching losses and offers excellent standby power performance. • Very Low Start-up Current: The patented internal supply block is specially designed to offer a very low current consumption during start-up. It allows the use of a very high value external start-up resistor, greatly reducing dissipation, improving efficiency and minimizing standby power consumption. • Natural Frequency Dithering: The quasi-fixed Ton mode of operation improves the EMI signature since the switching frequency varies with the natural bulk ripple voltage. • Peak Current Compression: As the load becomes lighter, the frequency decreases and can enter the audible range. To avoid exciting transformer mechanical resonances, hence generating acoustic noise, the NCP1215 includes a patented technique, which reduces the peak current as power goes down. As such, inexpensive transformer can be used without having noise problems. • Negative Primary Current Sensing: By sensing the total current, this technique does not modify the MOSFET driving voltage (Vgs) while switching. Furthermore, the programming resistor together with the pin capacitance, forms a residual noise filter which blanks spurious spikes. Also fixing primary current level to a maximum value sets the maximum power limit. • Programmable Primary Current Sense: It offers a second peak current adjustment variable which improves the design flexibility. • Secondary or Primary Regulation: The feedback loop arrangement allows simple secondary or primary side regulation without significant additional external components. A detailed description of each internal block within the IC is given below. The main task of the Feedback Loop Block is to control the SMPS output voltage through the change of primary switch OFF time interval. It sets the peak voltage of the timing capacitor, which varies upon the output power demand. Figure 13 shows the simplified internal schematic: VCC Current Mirror 1:1 Voffset + - 17 k FB Current Mirror 1:1 To OFF Time Comparator 45 k Figure 13. Feedback Loop - OFF Time Control OFF-T ime Comparator Input Voltage The voltage feedback signal is sensed as a current injected through the FB pin. VDD Voffset 0 A FB Pin Sink Current Figure 14. FB Loop Transfer Characteristic The transfer characteristic (output voltage to input current) of the feedback loop control block can be seen in Figure 14. VDD refers to the internal stabilized supply whereas the offset value sets the maximum switching frequency in lack of optocoupler current (e.g. an output short-circuit). To keep the switching frequency above the audio range in light load condition the FB pin also regulates in certain range the peak primary current. The corresponding block diagram can be seen from Figure 15. http://onsemi.com 7 NCP1215 To Current Sense Comparator From Feedback Loop Block 17 k FB - CS Voffset Current Mirror 4:3 37.5 A 12.5 A + Voffset to VDD − + Ct To Latch’s Set Input Figure 15. Feedback Loop - Current Sense Control 10 A The resulting current sense regulation characteristic can be seen from Figure 16. To Latch’s Output Ct 50 A CS Pin Source Current GND Figure 17. OFF Time Control During the switch-ON time, the Ct capacitor is kept discharged by a MOSFET switch. As soon as the latch output changes to a low state, the voltage across Ct created by the internal current source, starts to ramp-up until its value reaches the threshold given by the feedback loop demand. 12.5 A 0 A 50 A 100 A 140 A V FB Pin Sink Current Figure 16. Current Sense Regulation Characteristic VDD When the load goes light, the compression circuitry decreases the peak current. This has the effect of slightly increasing the switching frequency but the compression ratio is selected to not hamper the standby power. POUT Goes Down Ct Pin Voltage POUT Goes Up P3 OFF Time Control P2 Voffset The loop signal together with the internal current source, via an external capacitor, controls the switch-off time. This is portrayed in Figure 17. P1 toff- min t Figure 18. Ct Pin Voltage (Pout1 Pout2 Pout3) The voltage that can be observed on Ct pin is shown in Figure 18. The bold waveform shows the maximum output power when the OFF time is at its minimum. The IC allows an OFF time of several seconds. http://onsemi.com 8 NCP1215 Primary Current Sensing The primary current sensing method we described, brings the following benefits compared to the traditional approach: • Maximum peak voltage across the current sense resistor is determined and can be optimized by the value of the shift resistor. • CS pin is not exposed to negative voltage, which could induce a parasitic substrate current within the IC and distort the surrounding internal circuitry. • The gate drive capability is improved because the current sense resistor is located out of the gate driver loop and does not deteriorate the turn-on and also turn-of f gate drive amplitude. The primary current sensing circuit is shown in Figure 19. FB Feedback Loop Control 12.5 A 50 A CS + − Vshift Rshift To Latch Gate Driver GND The Gate Driver consists of a CMOS buffer designed to directly drive a power MOSFET. It features an unbalanced source and sink capabilities to optimize turn ON and OFF performance without additional external components. Since the power MOSFET turns-off at high drain current, to minimize its turn-off losses the sink capability of the gate driver is increased for a faster turn-off. To the opposite, the source capability is lower to slow-down power MOSFET at turn-on in order to reduce the EMI noise. Whenever the IC supply voltage is lower than the undervoltage threshold, the Gate Driver is low, pulling down the gate to ground. It eliminates the need for an external resistor. RCS VCS Iprimary Figure 19. Primary Current Sensing When the primary switch is ON, the transformer current flows through the sense resistor Rcs. The current creates a voltage, Vcs which is negative with respect to GND. Since the comparator connected to CS pin requires a positive voltage, the voltage Vshift is developed across the resistor Rshift by a current source which level-shifts the negative voltage Vcs. The level-shift current is in range from 12.5 to 50 A depending on the Feedback Loop Control block signal (see more details in the Feedback Loop Control section). The peak primary current is thus equal to: R Ipk shift · ICS RCS Start-Up Circuit An external start-up resistor is connected between high voltage potential of the input bulk capacitor and Vcc supply capacitor. The value of the resistor can be calculated as follows: (eq. 1) Rstart- up A typical CS pin voltage waveform is shown in Figure 20. Vbulk Vstart- up Istart- up (eq. 2) Where: Vstart- up Vcc voltage at which IC starts operation (see spec.) Istart- up Start-up current Vbulk Input bulk capacitor’s voltage Since the Vbulk voltage has obviously much higher value than Vstart- up the equation can be simplified in the following way: V Ishift = 50 A Rstart- up Ishift = 12.5 A Vbulk Istart- up (eq. 3) The start-up current can be calculated as follows: Vstart- up Istart- up CVcc ICC- start (eq. 4) tstart- up 0 Switch Turn-on t Where: CVcc tstart- up ICC- start Figure 20. CS Pin Voltage Figure 20 also shows the effect of the inductor current of differing output power demand. http://onsemi.com 9 Vcc capacitor value Start-up time IC current consumption (see spec.) NCP1215 Application Design Example If the IC current consumption is assumed constant during the start-up phase, one can obtain resulting equation for start-up resistor calculation: Rstart- up Vbulk CVcc Vstart- up tstart- up An example of the typical wall adapter application is described hereafter. As a wall adapter it should be able to operate properly with wide range of the input voltage from 90 VAC up to 265 VAC. The bulk capacitor voltage then can be calculated: (eq. 5) ICC- start Vbulk- min VAC- min 2 90 · 2 127 VDC Switching Frequency (eq. 11) The switching frequency varies with the output load and input voltage. The highest frequency appears at highest input voltage and maximum output power. Since the peak primary current is fixed, the on time portion of the switching period can be calculated: Ipk ton Lp Vbulk Vbulk- max VAC- max 2 265 · 2 375 VDC (eq. 12) The requested output power is 5.2 Watts. Assuming 80% efficiency the input power is equal to: (eq. 6) P 5.2 Pin out 0.8 6.5 W Where: Lp Transformer primary inductance Ipk Peak primary current Using equation for peak primary current estimation the switch-on time is: Rshift ton Lp 50 · 10- 6 Rcs · Vbulk The average value of input current at minimum input voltage is: Iin- avg V Pin 6.5 51.2 mA (eq. 14) 127 bulk- min The suitable reflected primary winding voltage for 600 V rated MOSFET switch is: (eq. 7) Vflbk 600 V Vbulk- max Vspike (eq. 15) 600 375 100 125 V Minimum switch-on time occurs at maximum input voltage: Using calculated flyback voltage the maximum duty cycle can be calculated: Rshift ton- min Lp 50 · 10- 6 (eq. 8) Rcs · Vbulk- max Vflbk Vflbk Vbulk- min 125 0.496 0.5 125 127 As it can be seen from the above equation, the switch-on time linearly depends on the input bulk capacitor voltage. Since this voltage has ripple due to AC input voltage and input rectifier, it allows natural frequency dithering to improve EMI signature of the SMPS. The switch-off time is determined by the charge of an external capacitor connected to the CT pin. The minimum Toff value can be computed by: V toff- min CT offset CT 1.2 ICt 10- 5 0.12 · 106 CT (eq. 13) max (eq. 16) Following equation determines peak primary current: Ippk 2 · Iin- avg max -3 2 · 51.2 · 10 0.5 (eq. 17) 204.7 mA The desired maximum switching frequency at minimum input voltage is 75 kHz. The highest switching frequency occurs at the highest input voltage and its value can be estimated as follows: (eq. 9) Where: Voffset Offset voltage (see spec.) ICt CT pin source current (see spec.) The maximum switching frequency then can be evaluated by: f max - high f max - low Vbulk- max Vbulk- min max(eq. 18) 75 · 103 375 0.5 110.7 kHz 127 This frequency is much below 150 kHz, so that the desired operating frequency can be exploited for further calculation of the primary inductance: 1 fsw- max ton- min toff- min (eq. 10) 1 Lp · Rshift 6 6 · 50 · 10 0.12 · 10 · CT V · max Lp bulk- min Ippk · fsw- max Vbulk · Rcs As output power diminishes, the switching frequency decreases because the switch-off time prolongs upon feedback loop. The range of the frequency change is sufficient to keep output voltage regulation in any light load condition. 127 · 0.5 4.14 mH 0.2047 · 75 · 103 http://onsemi.com 10 (eq. 19) NCP1215 The EF16 core for transformer was selected. It has cross-section area Ae = 20.1 mm2. The N67 magnetic allows to use maximum operating flux density Bmax = 0.28 Tesla. The number of turns of the primary winding is: Lp · Ippk np B max · Ae V RCS CS 0.5 2.442 2.7 0.2047 Ippk The voltage drop across the sense resistor needs to be recalculated: VCS RCS · Ippk 2.7 · 0.2047 0.553 V (eq. 25) Using the above results the value of the shift resistor is: (eq. 20) V Rshift CS 0.553 11.06 k 11 k ICS 50 · 10- 6 (eq. 26) -3 4.14 · 10 · 0.2047 150 turns 0.28 · 20.1 · 10- 6 The value of timing capacitor for the off time control has to be calculated for minimum bulk capacitor voltage since at these conditions the converter should be able to deliver specified maximum output power. The value of the timing capacitor is then given by the following equation: The AL factor of the transformer’s core can be calculated: AL Lp (np)2 -3 4.14 · 10 · 184 nH 2 (150) (eq. 21) For an adapter output voltage of 6.5 V, the number of turns of the secondary winding can be calculated accounting Schottky diode for output rectifier as follows: ns CT (Vs Vfwd)(1 max)np max · Vbulk- min (eq. 22) (6.5 0.7)(1 0.5)150 8.5 9 turns 0.5 · 127 Lp · Ippk V bulk- min 1.2 · 106 1 75 · 103 (eq. 27) 3 4.14 · 10127 · 0.2047 55.5 pF 56 pF 0.12 · 106 Rstart- up (Vs Vfwd)(1 max)np max · Vbulk- min 1 fsw The value of the start-up resistor for start-up time of 200 ms and Vcc capacitor of 200 nF is following: The number of turns for auxiliary winding can be calculated similarly: ns (eq. 24) (eq. 23) Vbulk- min CVcc tstart- up ICC- start MAX (12 1)(1 0.5)150 15.35 15 turns 0.5 · 127 Vstart- up 200 · 10- 9 127 12 10 · 10- 6 0.2 5.77 M 5.6 M The peak primary current is known from initial calculations. The current sense method allows choosing the voltage drop across the current sense resistor. Let’s use a value of 0.5 V. The value of the current sense resistor can then be evaluated as follows: (eq. 28) The result of all the calculations is the application schematic depicted in Figure 21. http://onsemi.com 11 NCP1215 3 J1 Line 1 J2 Neutral 1 L1 + 1 S250 T1 2.2 mH C1 + C2 4 2 - 1 nF/Y C8 D1 2.2 F/ 400 V 2.2 F/ 400 V 4 + R3 2M7 100 nF D5 3 R7 LL4448 C3 1 FB 2M7 NC1 8 R6 47 k X 10 nF C4 2 CT 56 pF 3 11 k R2 R1 2.7 4 CS GND NC2 7 X VCC Gate R5 220 C6 100 nF 5 5 1 47 k 1 nF/ 500 V 470 F/ 16 V + L2 4.7 H J3 +6.5 V@ 1 800 mA R8 220 10 F/ 16 V + R9 1k C7 D8 6 D9 MBRS360T3 C9 C5 R4 IC1 8 C10 2 MURA160T3 Q1 MTD1N60 BZX84C5V6 D7 NCP1215 J4 1 GND ISO1 PC817 Figure 21. Adaptor Application Schematic The following oscilloscope snapshots illustrate the operation of the working adapter. The Channel 3 in Figure 22 shows Ct pin voltage at full output load. The Channel 1 is a gate driver output. The Ct voltage at no load condition is depicted in Figure 23. Figure 22. Ct Voltage at Full Load Condition Figure 23. Ct Voltage at No Load Condition http://onsemi.com 12 NCP1215 Figure 24 shows Ct voltage and also by Channel 2 the switch’s drain voltage at light load conditions. Figure 26 demonstrates the reduction of the peak primary current at light load conditions. Figure 24. Ct and Drain at Light Load Figure 26. CS Pin at Light Load Condition The waveform on the current sense pin at full load conditions can be observed from Channel 3 in Figure 25. Figure 25. CS Pin at Full Load Condition http://onsemi.com 13 NCP1215 PACKAGE DIMENSIONS SO-8 CASE 751-07 ISSUE AA NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDAARD IS 751−07 -XA 8 5 0.25 (0.010) S B 1 M Y M 4 K -YG C N X 45 SEATING PLANE -Z- 0.10 (0.004) H M D 0.25 (0.010) M Z Y S X S http://onsemi.com 14 J DIM A B C D G H J K M N S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0 8 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 8 0.010 0.020 0.228 0.244 NCP1215 PACKAGE DIMENSIONS TSOP-6 CASE 318G-02 ISSUE H A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. L 6 S 1 5 4 2 3 B D G M J C 0.05 (0.002) H K http://onsemi.com 15 DIM A B C D G H J K L M S MILLIMETERS MIN MAX 2.90 3.10 1.30 1.70 0.90 1.10 0.25 0.50 0.85 1.05 0.013 0.100 0.10 0.26 0.20 0.60 1.25 1.55 0 10 2.50 3.00 INCHES MIN MAX 0.1142 0.1220 0.0512 0.0669 0.0354 0.0433 0.0098 0.0197 0.0335 0.0413 0.0005 0.0040 0.0040 0.0102 0.0079 0.0236 0.0493 0.0610 0 10 0.0985 0.1181 NCP1215 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 16 NCP1215/D