NL74VCXH16374 Low-Voltage 1.8/2.5/3.3V 16-Bit D-Type Flip-Flop With 3.6V–Tolerant Inputs and Outputs (3–State, Non–Inverting) The NL74VCXH16374 is an advanced performance, non–inverting 16–bit D–type flip–flop. It is designed for very high–speed, very low–power operation in 1.8V, 2.5V or 3.3V systems. The VCX16374 is byte controlled, with each byte functioning identically, but independently. Each byte has separate Output Enable and Clock Pulse inputs. These control pins can be tied together for full 16–bit operation. When operating at 2.5V (or 1.8V) the part is designed to tolerate voltages it may encounter on either inputs or outputs when interfacing to 3.3V busses. It is guaranteed to be over–voltage tolerant to 3.6V. The NL74VCXH16374 consists of 16 edge–triggered flip–flops with individual D–type inputs and 3.6V–tolerant 3–state outputs. The clocks (CPn) and Output Enables (OEn) are common to all flip–flops within the respective byte. The flip–flops will store the state of individual D inputs that meet the setup and hold time requirements on the LOW–to–HIGH Clock (CP) transition. With the OE LOW, the contents of the flip–flops are available at the outputs. When the OE is HIGH, the outputs go to the high impedance state. The OE input level does not affect the operation of the flip–flops. The data inputs include active bushold circuitry, eliminating the need for external pull–up resistors to hold unused or floating inputs at a valid logic state. http://onsemi.com 48 1 TSSOP–48 DT SUFFIX CASE 1201 MARKING DIAGRAM 48 NL74VCXH16374DT AWLYYWW 1 A WL YY WW • Designed for Low Voltage Operation: VCC = 1.65–3.6V • 3.6V Tolerant Inputs and Outputs • High Speed Operation: 3.0ns max for 3.0 to 3.6V • • • 3.9ns max for 2.3 to 2.7V 7.8ns max for 1.65 to 1.95V Static Drive: ±24mA Drive at 3.0V ±18mA Drive at 2.3V ±6mA Drive at 1.65V Supports Live Insertion and Withdrawal Includes Active Bushold to Hold Unused or Floating Inputs at a Valid Logic State IOFF Specification Guarantees High Impedance When VCC = 0V† • • Near Zero Static Supply Current in All Three Logic States (20µA) • • Substantially Reduces System Power Requirements Latchup Performance Exceeds ±300mA @ 125°C ESD Performance: Human Body Model >2000V; Machine Model >200V = Assembly Location = Wafer Lot = Year = Work Week PIN NAMES Pins Function OEn CPn D0–D15 O0–O15 Output Enable Inputs Clock Pulse Inputs Inputs Outputs ORDERING INFORMATION Package Shipping NL74VCXH16374DT Device TSSOP 39 / Rail NL74VCXH16374DTR TSSOP 2500 / Reel †NOTE: To ensure the outputs activate in the 3–state condition, the output enable pins should be connected to VCC through a pull–up resistor. The value of the resistor is determined by the current sinking capability of the output connected to the OE pin. Semiconductor Components Industries, LLC, 2000 May, 2000 – Rev. 0 Powered by ICminer.com Electronic-Library Service CopyRight 2003 1 Publication Order Number: NL74VCXH16374/D NL74VCXH16374 OE1 1 48 CP1 OE1 O0 2 47 D0 CP1 O1 3 46 D1 GND 4 45 GND O2 5 44 D2 O3 6 43 D3 VCC 7 O4 8 42 VCC 41 D4 O5 9 1 48 39 GND O6 11 38 D6 O7 12 37 D7 O8 13 36 D8 O9 14 35 D9 GND 15 D1 D3 33 D10 O11 17 32 D11 VCC 18 O12 19 31 VCC 30 D12 O13 20 29 D13 GND 21 28 GND O14 22 27 D14 O15 23 26 D15 OE2 24 25 CP2 Figure 1. 48–Lead Pinout (Top View) D5 D6 D7 D nCP D nCP D nCP D nCP D nCP 26 D15 nCP D nCP D 13 Q 14 Q 16 Q 17 Q 19 Q 20 Q 22 Q 23 Q O8 O9 O10 O11 O12 O13 O14 O15 Figure 2. Logic Diagram 1 OE1 48 CP1 25 CP2 24 OE2 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 Inputs O7 Q D 27 D14 12 nCP 37 nCP D O6 Q D 29 D13 11 nCP 38 O5 Q D 30 D12 9 nCP 40 O4 Q D 32 D11 8 nCP 41 D4 O3 Q D 33 D10 6 nCP 43 O2 Q D 35 D9 5 nCP 36 O1 Q D 25 D8 3 nCP 24 O0 Q D 44 D2 2 nCP 46 34 GND O10 16 CP2 47 D0 40 D5 GND 10 OE2 47 46 44 43 41 40 38 37 36 35 33 32 30 29 27 26 EN1 EN2 EN3 EN4 1 1∇ 1 2∇ 1 3∇ 1 4∇ Outputs 2 3 5 6 8 9 11 12 13 14 16 17 19 20 22 23 O0 O1 O2 O3 O4 O5 O6 O7 O8 O9 O10 O11 O12 O13 O14 O15 Inputs Outputs CP1 OE1 D0:7 O0:7 CP2 OE2 D8:15 O8:15 ↑ L H H ↑ L H H ↑ L L L ↑ L L L X L X O0 X L X O0 X H X Z X H X Z H = High Voltage Level; L = Low Voltage Level; Z = High Impedance State; ↑ = Low–to–High Transition; X = High or Low Voltage Level and Transitions Are Acceptable, for ICC reasons, DO NOT FLOAT Inputs. O0 = No Change. http://onsemi.com 2 Powered by ICminer.com Electronic-Library Service CopyRight 2003 NL74VCXH16374 ABSOLUTE MAXIMUM RATINGS* Symbol Parameter VCC DC Supply Voltage VI VO Value Condition Unit –0.5 to +4.6 V DC Input Voltage –0.5 ≤ VI ≤ +4.6 V DC Output Voltage –0.5 ≤ VO ≤ +4.6 Output in 3–State V –0.5 ≤ VO ≤ VCC + 0.5 Note 1.; Outputs Active V IIK DC Input Diode Current –50 VI < GND mA IOK DC Output Diode Current –50 VO < GND mA +50 VO > VCC mA IO DC Output Source/Sink Current ±50 mA ICC DC Supply Current Per Supply Pin ±100 mA IGND DC Ground Current Per Ground Pin ±100 mA TSTG Storage Temperature Range –65 to +150 °C * Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions is not implied. 1. IO absolute maximum rating must be observed. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Operating Data Retention Only Min Typ Max Unit 1.65 1.2 3.3 3.3 3.6 3.6 V –0.3 3.6 V 0 0 VCC 3.6 V VCC Supply Voltage VI Input Voltage VO Output Voltage IOH HIGH Level Output Current, VCC = 3.0V – 3.6V –24 mA IOL LOW Level Output Current, VCC = 3.0V – 3.6V 24 mA IOH HIGH Level Output Current, VCC = 2.3V – 2.7V –18 mA IOL LOW Level Output Current, VCC = 2.3V – 2.7V 18 mA IOH HIGH Level Output Current, VCC = 1.65 – 1.95V –6 mA IOL LOW Level Output Current, VCC = 1.65 – 1.95V 6 mA TA Operating Free–Air Temperature –40 +85 °C ∆t/∆V Input Transition Rise or Fall Rate, VIN from 0.8V to 2.0V, VCC = 3.0V 0 10 ns/V (Active State) (3–State) http://onsemi.com 3 Powered by ICminer.com Electronic-Library Service CopyRight 2003 NL74VCXH16374 DC ELECTRICAL CHARACTERISTICS TA = –40°C to +85°C Symbol VIH VIL VOH VOL II II(HOLD) II (OD) 2. 3. 4. 5. Characteristic Condition Min HIGH Level Input Voltage (Note 2.) 1.65V ≤ VCC < 2.3V 0.65 x VCC 2.3V ≤ VCC ≤ 2.7V 1.6 2.7V < VCC ≤ 3.6V 2.0 LOW Level Input Voltage (Note 2.) HIGH Level Output Voltage LOW Level Output Voltage Input Leakage Current Minimum Bushold Input Current Minimum Bushold Over–Drive C rrent Needed to Change State Current IOZ 3–State Output Current IOFF ICC Power–Off Leakage Current Quiescent Supply Current (Note 5.) 0.35 x VCC 2.3V ≤ VCC ≤ 2.7V 0.7 2.7V < VCC ≤ 3.6V 0.8 1.65V ≤ VCC ≤ 3.6V; IOH = –100µA VCC – 0.2 VCC = 1.65V; IOH = –6mA 1.25 VCC = 2.3V; IOH = –6mA 2.0 VCC = 2.3V; IOH = –12mA 1.8 VCC = 2.3V; IOH = –18mA 1.7 VCC = 2.7V; IOH = –12mA 2.2 VCC = 3.0V; IOH = –18mA 2.4 VCC = 3.0V; IOH = –24mA 2.2 Unit V 1.65V ≤ VCC < 2.3V V V 1.65V ≤ VCC ≤ 3.6V; IOL = 100µA 0.2 VCC = 1.65V; IOL = 6mA 0.3 VCC = 2.3V; IOL = 12mA VCC = 2.3V; IOL = 18mA 0.4 VCC = 2.7V; IOL = 12mA 0.4 VCC = 3.0V; IOL = 18mA 0.4 VCC = 3.0V; IOL = 24mA 0.55 1.65V ≤ VCC ≤ 3.6V; 0V ≤ VI ≤ 3.6V ±5.0 V 0.6 VCC = 3.0V, VIN = 0.8V 75 VCC = 3.0V, VIN = 2.0V –75 VCC = 2.3V, VIN = 0.7V 45 VCC = 2.3V, VIN = 1.6V –45 VCC = 1.65V, VIN = 0.57V 25 VCC = 1.65V, VIN = 1.07V –25 VCC = 3.6V, (Note 3.) 450 VCC = 3.6V, (Note 4.) –450 VCC = 2.7V, (Note 3.) 300 VCC = 2.7V, (Note 4.) –300 VCC = 1.95V, (Note 3.) 200 VCC = 1.95V, (Note 4.) –200 µA µA µA 1.65V ≤ VCC ≤ 3.6V; 0V ≤ VO ≤ 3.6V; VI = VIH or VIL ±10 µA VCC = 0V; VI or VO = 3.6V 10 µA 1.65V ≤ VCC ≤ 3.6V; VI = GND or VCC 20 µA 1.65V ≤ VCC ≤ 3.6V; 3.6V ≤ VI, VO ≤ 3.6V ±20 µA 750 µA ∆ICC Increase in ICC per Input 2.7V < VCC ≤ 3.6V; VIH = VCC – 0.6V These values of VI are used to test DC electrical characteristics only. An external driver must source at least the specified current to switch from LOW–to–HIGH An external driver must source at least the specified current to switch from HIGH–to–LOW Outputs disabled or 3–state only. http://onsemi.com 4 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Max NL74VCXH16374 AC CHARACTERISTICS (Note 6.; tR = tF = 2.0ns; CL = 30pF; RL = 500Ω) Limits TA = –40°C to +85°C VCC = 3.0V to 3.6V Symbol Parameter Waveform Min Max VCC = 2.3V to 2.7V Min Max 200 VCC = 1.65 to 1.95V Min Max fmax Clock Pulse Frequency 1 250 tPLH tPHL Propagation Delay CP to On 1 0.8 0.8 3.0 3.0 1.0 1.0 3.9 3.9 1.5 1.5 7.8 7.8 ns tPZH tPZL Output Enable Time to High and Low Level 2 0.8 0.8 3.5 3.5 1.0 1.0 4.6 4.6 1.5 1.5 9.2 9.2 ns tPHZ tPLZ Output Disable Time From High and Low Level 2 0.8 0.8 3.5 3.5 1.0 1.0 3.8 3.8 1.5 1.5 6.8 6.8 ns ts Setup Time, High or Low Dn to CP 3 1.5 1.5 2.5 ns th Hold Time, High or Low Dn to CP 3 1.0 1.0 1.0 ns tw CP Pulse Width, High 3 1.5 1.5 4.0 ns tOSHL tOSLH Output–to–Output Skew (Note 7.) 0.5 0.5 100 Unit 0.5 0.5 MHz 0.75 0.75 ns 6. For CL = 50pF, add approximately 300ps to the AC maximum specification. 7. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter guaranteed by design. DYNAMIC SWITCHING CHARACTERISTICS TA = +25°C Symbol VOLP VOLV VOHV Characteristic Condition Typ Unit Dynamic LOW Peak Voltage VCC = 1.8V, CL = 30pF, VIH = VCC, VIL = 0V 0.25 V (Note 8.) VCC = 2.5V, CL = 30pF, VIH = VCC, VIL = 0V 0.6 VCC = 3.3V, CL = 30pF, VIH = VCC, VIL = 0V 0.8 Dynamic LOW Valley Voltage VCC = 1.8V, CL = 30pF, VIH = VCC, VIL = 0V –0.25 (Note 8.) VCC = 2.5V, CL = 30pF, VIH = VCC, VIL = 0V –0.6 VCC = 3.3V, CL = 30pF, VIH = VCC, VIL = 0V –0.8 Dynamic HIGH Valley Voltage VCC = 1.8V, CL = 30pF, VIH = VCC, VIL = 0V 1.5 (Note 9.) VCC = 2.5V, CL = 30pF, VIH = VCC, VIL = 0V 1.9 V V VCC = 3.3V, CL = 30pF, VIH = VCC, VIL = 0V 2.2 8. Number of outputs defined as “n”. Measured with “n–1” outputs switching from HIGH–to–LOW or LOW–to–HIGH. The remaining output is measured in the LOW state. 9. Number of outputs defined as “n”. Measured with “n–1” outputs switching from HIGH–to–LOW or LOW–to–HIGH. The remaining output is measured in the HIGH state. CAPACITIVE CHARACTERISTICS Symbol Parameter Condition Typical Unit CIN Input Capacitance Note 10. 6 pF COUT Output Capacitance Note 10. 7 pF CPD Power Dissipation Capacitance Note 10., 10MHz 20 pF 10. VCC = 1.8, 2.5 or 3.3V; VI = 0V or VCC. http://onsemi.com 5 Powered by ICminer.com Electronic-Library Service CopyRight 2003 NL74VCXH16374 VIH VIH Dn Vm Vm OEn Vm Vm 0V 0V tPZH th ts tPHZ VOH Vy VIH CPn Vm Vm On Vm ≈ 0V 0V fmax tPLH, tPHL tPZL VOH On tPLZ ≈ VCC Vm On Vm Vx VOL VOL WAVEFORM 1 – PROPAGATION DELAYS, SETUP AND HOLD TIMES tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns WAVEFORM 2 – OUTPUT ENABLE AND DISABLE TIMES tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns Figure 3. AC Waveforms VIH CPn Vm Vm tw 0V VIH tw Vm CPn Vm 0V WAVEFORM 3 – PULSE WIDTH tR = tF = 2.0ns (or fast as required) from 10% to 90% Figure 4. AC Waveforms VCC Symbol 3.3V ±0.3V 2.5V ±0.2V 1.8V ±0.15V VIH 2.7V VCC VCC Vm 1.5V VCC/2 VCC/2 Vx VOL + 0.3V VOL + 0.15V VOL + 0.15V Vy VOH – 0.3V VOH – 0.15V VOH – 0.15V VCC PULSE GENERATOR RL DUT RT CL TEST RL SWITCH tPLH, tPHL Open tPZL, tPLZ 6V at VCC = 3.3 ±0.3V; VCC× 2 at VCC = 2.5 ±0.2V; 1.8V ±0.15V tPZH, tPHZ GND CL = 30pF or equivalent (Includes jig and probe capacitance) RL = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) Figure 5. Test Circuit http://onsemi.com 6 Powered by ICminer.com Electronic-Library Service CopyRight 2003 6V or VCC × 2 OPEN GND NL74VCXH16374 VIH VIH Dn Vm Vm OEn Vm Vm 0V 0V tPZH th ts tPHZ VIH CPn Vm Vm On Vm ≈ 0V 0V fmax tPLH, tPHL tPZL VOH On tPLZ Vx VOL VOL WAVEFORM 4 – PROPAGATION DELAYS, SETUP AND HOLD TIMES tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns WAVEFORM 5 – OUTPUT ENABLE AND DISABLE TIMES tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns Figure 6. AC Waveforms VIH Vm Vm tw 0V VIH tw Vm CPn Vm 0V WAVEFORM 6 – PULSE WIDTH tR = tF = 2.0ns (or fast as required) from 10% to 90% Figure 7. AC Waveforms VCC Symbol 3.3V ±0.3V 2.7V VIH 2.7V 2.7V Vm 1.5V 1.5V Vx VOL + 0.3V VOL + 0.3V Vy VOH – 0.3V VOH – 0.3V http://onsemi.com 7 Powered by ICminer.com Electronic-Library Service CopyRight 2003 ≈ VCC Vm On Vm CPn VOH Vy NL74VCXH16374 AC CHARACTERISTICS (tR = tF = 2.0ns; CL = 50pF; RL = 500Ω) Limits TA = –40°C to +85°C VCC = 3.0V to 3.6V Symbol Parameter Max VCC = 2.7V Waveform Min fmax Clock Pulse Frequency 4 150 Min Max tPLH tPHL Propagation Delay CP to On 4 1.0 1.0 4.2 4.2 4.9 4.9 ns tPZH tPZL Output Enable Time to High and Low Level 5 1.0 1.0 4.8 4.8 5.9 5.9 ns tPHZ tPLZ Output Disable Time From High and Low Level 5 1.0 1.0 4.3 4.3 4.7 4.7 ns tOSHL tOSLH Output–to–Output Skew (Note 11.) 0.5 0.5 0.5 0.5 ns 150 Unit MHz 11. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter guaranteed by design. VCC PULSE GENERATOR RL DUT CL RT RL SWITCH TEST tPLH, tPHL Open tPZL, tPLZ 6V at VCC = 3.3 ±0.3V; VCC× 2 at VCC = 2.5 ±0.2V; 1.8V ±0.15V tPZH, tPHZ GND CL = 50pF or equivalent (Includes jig and probe capacitance) RL = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) Figure 8. Test Circuit http://onsemi.com 8 Powered by ICminer.com Electronic-Library Service CopyRight 2003 6V or VCC × 2 OPEN GND NL74VCXH16374 PACKAGE DIMENSIONS TSSOP DT SUFFIX CASE 1201–01 ISSUE A 48X ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ K K1 K REF 0.12 (0.005) M T U S V S T U S J J1 48 25 SECTION N–N M 0.254 (0.010) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSIONS A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. B –U– L N 1 24 A –V– PIN 1 IDENT. N F DETAIL E D C 0.25 (0.010) –W– 0.076 (0.003) –T– SEATING DETAIL E PLANE MILLIMETERS MIN MAX 12.40 12.60 6.00 6.20 ––– 1.10 0.05 0.15 0.50 0.75 0.50 BSC 0.37 ––– 0.09 0.20 0.09 0.16 0.17 0.27 0.17 0.23 7.95 8.25 0_ 8_ H G ÉÉ ÉÉ ÉÉ É ÉÉ É ÉÉ ÉÉ ÉÉ É ÉÉ É ÉÉ ÉÉÉÉÉÉÉÉ ÉÉ ÉÉ ÉÉ É ÉÉ É ÉÉ ÉÉÉÉÉÉÉÉ ÉÉ ÉÉ ÉÉ ÉÉ É ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ É ÉÉ ÉÉÉÉ ÉÉÉÉÉÉÉ ÉÉ ÉÉ ÉÉ ÉÉ É ÉÉ ÉÉÉÉ ÉÉÉÉÉÉÉ F K L M DIM A B C D F G H J J1 K K1 L M G 48 Leads Package Footprint http://onsemi.com 9 Powered by ICminer.com Electronic-Library Service CopyRight 2003 INCHES MIN MAX 0.488 0.496 0.236 0.244 ––– 0.043 0.002 0.006 0.020 0.030 0.0197 BSC 0.015 ––– 0.004 0.008 0.004 0.006 0.007 0.011 0.007 0.009 0.313 0.325 0_ 8_ NL74VCXH16374 10 PITCHES CUMULATIVE TOLERANCE ON TAPE ±0.2 mm (±0.008”) P0 K P2 D t TOP COVER TAPE E A0 + K0 SEE NOTE 2 B1 SEE NOTE 2 F + B0 W + D1 FOR COMPONENTS 2.0 mm × 1.2 mm AND LARGER P EMBOSSMENT FOR MACHINE REFERENCE ONLY INCLUDING DRAFT AND RADII CONCENTRIC AROUND B0 CENTER LINES OF CAVITY USER DIRECTION OF FEED *TOP COVER TAPE THICKNESS (t1) 0.10 mm (0.004”) MAX. R MIN. TAPE AND COMPONENTS SHALL PASS AROUND RADIUS “R” WITHOUT DAMAGE EMBOSSED CARRIER BENDING RADIUS 10° 100 mm (3.937”) MAXIMUM COMPONENT ROTATION EMBOSSMENT 1 mm MAX TYPICAL COMPONENT CAVITY CENTER LINE TAPE 1 mm (0.039”) MAX TYPICAL COMPONENT CENTER LINE 250 mm (9.843”) CAMBER (TOP VIEW) ALLOWABLE CAMBER TO BE 1 mm/100 mm NONACCUMULATIVE OVER 250 mm Figure 9. Carrier Tape Specifications EMBOSSED CARRIER DIMENSIONS (See Notes 1 and 2) Tape Size B1 Max 24mm 20.1mm (0.791”) D D1 E F K P P0 P2 R T W 1.5 + 0.1mm –0.0 (0.059 +0.004” –0.0) 1.5mm Min (0.060”) 1.75 ±0.1 mm (0.069 ±0.004”) 11.5 ±0.10 mm (0.453 ±0.004”) 11.9 mm Max (0.468”) 16.0 ±0.1 mm (0.63 ±0.004”) 4.0 ±0.1 mm (0.157 ±0.004”) 2.0 ±0.1 mm (0.079 ±0.004”) 30 mm (1.18”) 0.6 mm (0.024”) 24.3 mm (0.957”) 1. Metric Dimensions Govern–English are in parentheses for reference only. 2. A0, B0, and K0 are determined by component size. The clearance between the components and the cavity must be within 0.05 mm min to 0.50 mm max. The component cannot rotate more than 10° within the determined cavity http://onsemi.com 10 Powered by ICminer.com Electronic-Library Service CopyRight 2003 NL74VCXH16374 t MAX 13.0 mm ±0.2 mm (0.512” ±0.008”) 1.5 mm MIN (0.06”) A 20.2 mm MIN (0.795”) 50 mm MIN (1.969”) FULL RADIUS G Figure 10. Reel Dimensions REEL DIMENSIONS Tape Size A Max G t Max 24 mm 360 mm (14.173”) 24.4 mm + 2.0 mm, –0.0 (0.961” + 0.078”, –0.00) 30.4 mm (1.197”) DIRECTION OF FEED BARCODE LABEL POCKET Figure 11. Reel Winding Direction http://onsemi.com 11 Powered by ICminer.com Electronic-Library Service CopyRight 2003 HOLE NL74VCXH16374 CAVITY TAPE TOP TAPE TAPE TRAILER (Connected to Reel Hub) NO COMPONENTS 160 mm MIN COMPONENTS TAPE LEADER NO COMPONENTS 400 mm MIN DIRECTION OF FEED Figure 12. Tape Ends for Finished Goods User Direction of Feed Figure 13. Reel Configuration ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada N. American Technical Support: 800–282–9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor – European Support German Phone: (+1) 303–308–7140 (M–F 1:00pm to 5:00pm Munich Time) Email: ONlit–[email protected] French Phone: (+1) 303–308–7141 (M–F 1:00pm to 5:00pm Toulouse Time) Email: ONlit–[email protected] English Phone: (+1) 303–308–7142 (M–F 12:00pm to 5:00pm UK Time) Email: [email protected] EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781 *Available from Germany, France, Italy, England, Ireland CENTRAL/SOUTH AMERICA: Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST) Email: ONlit–[email protected] ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001–800–4422–3781 Email: ONlit–[email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549 Phone: 81–3–5740–2745 Email: [email protected] ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 12 Powered by ICminer.com Electronic-Library Service CopyRight 2003 NL74VCXH16374/D