74ALVCH16373 Low-Voltage 16-Bit Transparent Latch with Bus Hold 1.8/2.5/3.3 V (3–State, Non–Inverting) The 74ALVCH16373 is an advanced performance, non–inverting 16–bit transparent latch. It is designed for very high–speed, very low–power operation in 1.8 V, 2.5 V or 3.3 V systems. The VCXH16373 is byte controlled, with each byte functioning identically, but independently. Each byte has separate Output Enable and Latch Enable inputs. These control pins can be tied together for full 16–bit operation. The 74ALVCH16373 contains 16 D–type latches with 3–state 3.6 V–tolerant outputs. When the Latch Enable (LEn) inputs are HIGH, data on the Dn inputs enters the latches. In this condition, the latches are transparent, (a latch output will change state each time its D input changes). When LE is LOW, the latch stores the information that was present on the D inputs a setup time preceding the HIGH–to–LOW transition of LE. The 3–state outputs are controlled by the Output Enable (OEn) inputs. When OE is LOW, the outputs are enabled. When OE is HIGH, the standard outputs are in the high impedance state, but this does not interfere with new data entering into the latches. The data inputs include active bushold circuitry, eliminating the need for external pull–up resistors to hold unused or floating inputs at a valid logic state. • Designed for Low Voltage Operation: VCC = 1.65 – 3.6 V • 3.6 V Tolerant Inputs and Outputs • High Speed Operation: 3.0 ns max for 3.0 to 3.6 V • • • 3.9 ns max for 2.3 to 2.7 V 6.8 ns max for 1.65 to 1.95 V Static Drive: ±24 mA Drive at 3.0 V ±18 mA Drive at 2.3 V ±6 mA Drive at 1.65 V Supports Live Insertion and Withdrawal Includes Active Bushold to Hold Unused or Floating Inputs at a Valid Logic State IOFF Specification Guarantees High Impedance When VCC = 0 V† http://onsemi.com MARKING DIAGRAM 48 48 74ALVCH16373DT 1 AWLYYWW TSSOP–48 DT SUFFIX CASE 1201 A WL YY WW 1 = Assembly Location = Wafer Lot = Year = Work Week PIN NAMES Pins Function OEn LEn D0–D15 O0–O15 Output Enable Inputs Latch Enable Inputs Inputs Outputs ORDERING INFORMATION Device Package Shipping 74ALVCH16373DT TSSOP 39 Units/Rail 74ALVCH16373DTR TSSOP 2500/Tape & Reel • • Near Zero Static Supply Current in All Three Logic States (20 µA) Substantially Reduces System Power Requirements • Latchup Performance Exceeds ±250 mA @ 125°C • ESD Performance: Human Body Model >2000 V; Machine Model >200 V • Second Source to Industry Standard 74ALVCH16373 †To ensure the outputs activate in the 3–state condition, the output enable pins should be connected to VCC through a pull–up resistor. The value of the resistor is determined by the current sinking capability of the output connected to the OE pin. Semiconductor Components Industries, LLC, 2001 November, 2001 – Rev. 0 1 Publication Order Number: 74ALVCH16373/D 74ALVCH16373 OE1 1 O0 2 48 LE1 47 D0 O1 3 GND 4 O2 5 46 D1 45 GND OE1 LE1 D0 44 D2 43 D3 O3 6 VCC 7 42 VCC 41 D4 O4 8 O5 9 40 D5 39 GND GND 10 O6 11 38 D6 37 D7 O7 12 O8 13 36 D8 35 D9 O9 14 GND 15 O10 16 34 GND 33 D10 O11 17 VCC 18 32 D11 31 VCC GND 21 O14 22 28 GND 27 D14 O15 23 OE2 24 26 D15 25 LE2 O12 19 O13 20 30 D12 29 D13 Figure 1. 48–Lead Pinout (Top View) D1 D2 D3 D4 D5 D6 D7 1 OE2 48 LE2 nLE 47 D nLE 46 D nLE 44 D nLE 43 D nLE 41 D nLE 40 D nLE 38 D nLE 37 D 2 Q 3 Q 5 Q 6 Q 8 Q 9 Q 11 Q 12 Q O0 24 25 36 D8 O1 35 D9 O2 33 D10 O3 32 D11 O4 30 D12 O5 29 D13 O6 27 D14 O7 26 D15 nLE D nLE D nLE D nLE D nLE D nLE D nLE D nLE D 13 Q 14 Q 16 Q 17 Q 19 Q 20 Q 22 Q 23 Q O8 O9 O10 O11 O12 O13 O14 O15 Figure 2. Logic Diagram 1 OE1 LE1 48 25 LE2 24 OE2 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 EN1 EN2 EN3 EN4 47 46 44 43 41 40 38 37 36 35 33 32 30 29 27 26 1 1∇ 1 2∇ 1 3∇ 1 4∇ 2 3 5 6 8 9 11 12 13 14 16 17 19 20 22 23 O0 O1 O2 O3 O4 O5 O6 O7 O8 O9 O10 O11 O12 O13 O14 O15 Figure 3. IEC Logic Diagram Inputs Outputs Inputs Outputs LE1 OE1 D0:7 O0:7 LE2 OE2 D8:15 O8:15 X H X Z X H X Z H L L L H L L L H L H H H L H H L L X O0 L L X O0 H = High Voltage Level; L = Low Voltage Level; Z = High Impedance State; X = High or Low Voltage Level and Transitions Are Acceptable, for ICC reasons, DO NOT FLOAT Inputs. O0 = No Change. http://onsemi.com 2 74ALVCH16373 MAXIMUM RATINGS (Note 1) Symbol Parameter Value Unit VCC DC Supply Voltage 0.5 to 4.6 V VI DC Input Voltage 0.5 to 4.6 V VO DC Output Voltage 0.5 to 4.6 V IIK DC Input Diode Current VI < GND 50 mA IOK DC Output Diode Current VO < GND 50 mA IO DC Output Sink Current 50 mA ICC DC Supply Current per Supply Pin 100 mA IGND DC Ground Current per Ground Pin 100 mA TSTG Storage Temperature Range 65 to 150 C TL Lead Temperature, 1 mm from Case for 10 Seconds TJ Junction Temperature Under Bias JA Thermal Resistance (Note 2) MSL Moisture Sensitivity FR Flammability Rating VESD ESD Withstand Voltage 260 C 150 C 90 C/W Level 1 Oxygen Index: 30% – 35% UL–94–VO (0.125 in) 2000 200 N/A Human Body Model (Note 3) Machine Model (Note 4) Charged Device Model (Note 5) V ILATCH–UP Latch–Up Performance Above VCC and Below GND at 85C (Note 6) 250 mA Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum–rated conditions is not implied. Functional operation should be restricted to the Recommended Operating Conditions. 1. IO absolute maximum rating must be observed. 2. Measured with minimum pad spacing on an FR4 board, using 10 mm–by–1 inch, 2–ounce copper trace with no air flow. 3. Tested to EIA/JESD22–A114–A. 4. Tested to EIA/JESD22–A115–A. 5. Tested to JESD22–C101–A. 6. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage VI Input Voltage VO Output Voltage TA Operating Free–Air Temperature t/V Input Transition Rise or Fall Rate Operating Data Retention Only (Note 7) (HIGH or LOW State) VCC = 2.5 V 0.2 V VCC = 3.0 V 0.3 V VCC = 5.0 V 0.5 V Min Max Unit 2.3 1.5 3.6 3.6 V 0 3.6 V 0 3.6 V 40 85 C 0 0 0 20 10 5 ns/V 7. Unused inputs may not be left open. All inputs must be tied to a high–logic voltage level or a low–logic input voltage level. http://onsemi.com 3 74ALVCH16373 DC ELECTRICAL CHARACTERISTICS TA = 40C to 85C Symbol VIH VIL VOH VOL Parameter HIGH Level Input Voltage ( (Note 8)) LOW Level Input Voltage ( (Note 8)) HIGH Level Output Voltage LOW Level Output Voltage Condition Min 1.65 V VCC 2.3 V 0.65 VCC 2.3 V VCC 2.7 V 1.7 2.7 V VCC 3.6 V 2.0 Max V 1.65 V VCC 2.3 V 0.35 VCC 2.3 V VCC 2.7 V 0.7 2.7 V VCC 3.6 V 0.8 1.65 V VCC 3.6 V; IOH = 100 A VCC 0.2 VCC = 1.65 V; IOH = 4 mA 1.20 VCC = 2.3 V; IOH = 6 mA 2.0 VCC = 2.3 V; IOH = 12 mA 1.7 VCC = 2.7 V; IOH = 12 mA 2.2 VCC = 3.0 V; IOH = 12 mA 2.4 VCC = 3.0 V; IOH = 24 mA 2.0 0.2 VCC = 1.65 V; IOL = 4 mA 0.45 VCC = 2.3 V; IOL = 6 mA 0.4 VCC = 2.3 V; IOL = 12 mA 0.7 VCC = 2.7 V; IOL = 12 mA 0.4 VCC = 3.0 V; IOL = 24 mA 0.55 LOW Level Output Voltage VCC = 3.6 V; VI = 0 to 3.6 V II Input Leakage Current 1.65 V VCC 3.6 V; 0 V VI 3.6 V II(HOLD) Minimum Bus–hold Input Current VCC = 3.0 V, VIN = 0.8 V 75 VCC = 3.0 V, VIN = 2.0 V 75 VCC = 2.3 V, VIN = 0.7 V 45 VCC = 2.3 V, VIN = 1.7 V 45 VCC = 1.65 V, VIN = 0.58 V 25 VCC = 1.65 V, VIN = 1.07 V 25 IOZ 3–State Output Current 1.65 V VCC 3.6 V; 0 V VO 3.6 V; VI = VIH or VIL IOFF Power–Off Leakage Current ICC Quiescent Supply Current (N (Note 9)) V V 1.65 V VCC 3.6 V; IOL = 100 A VOL Unit V 500 A 5.0 A A 10 A VCC = 0 V; VI or VO = 3.6 V 10 A 1.65 V VCC 3.6 V; VI = GND or VCC 40 A 1.65 V VCC 3.6 V; 3.6 V VI, VO 3.6 V ICC Increase in ICC per Input 2.7 V VCC ≤ 3.6 V; VIH = VCC 0.6 V 8. These values of VI are used to test DC electrical characteristics only. 9. Outputs disabled or 3–state only. http://onsemi.com 4 40 750 A 74ALVCH16373 AC CHARACTERISTICS (Note 10; tR = tF = 2.0 ns; CL = 30 pF; RL = 500 Ω) Limits TA = –40°C to +85°C VCC = 3.0 V t o 3.6 V Symbol Parameter VCC = 2.3 V to 2.7 V VCC = 1.65 V to 1.95 V Waveform Min Max Min Max Min Max Unit tPLH tPHL Propagation Delay Dn to On 1 0.5 0.5 3.0 3.0 0.5 0.5 3.4 3.4 0.5 0.5 6.8 6.8 ns tPLH tPHL Propagation Delay LE to On 1 0.5 0.5 3.0 3.0 0.5 0.5 3.9 3.9 0.5 0.5 7.8 7.8 ns tPZH tPZL Output Enable Time to High and Low Level 2 0.5 0.5 3.5 3.5 0.5 0.5 4.6 4.6 0.5 0.5 9.2 9.2 ns tPHZ tPLZ Output Disable Time From High and Low Level 2 0.5 0.5 3.5 3.5 0.5 0.5 3.8 3.8 0.5 0.5 6.8 6.8 ns ts Setup Time, High or Low Dn to LE 3 1.5 1.5 2.5 ns th Hold Time, High or Low Dn to LE 3 1.0 1.0 1.0 ns tw LE Pulse Width, High 3 1.5 1.5 4.0 ns tOSHL tOSLH Output–to–Output Skew (Note 11) 0.5 0.5 0.5 0.5 0.75 0.75 ns 10. For CL = 50 pF, add approximately 300 ps to the AC maximum specification. 11. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter guaranteed by design. CAPACITIVE CHARACTERISTICS Symbol Parameter Condition Typical Unit CIN Input Capacitance Note 12 6 pF COUT Output Capacitance Note 12 7 pF Note 12, 10 MHz 20 pF CPD Power Dissipation Capacitance 12. VCC = 1.8, 2.5 or 3.3 V; VI = 0V or VCC. VIH Dn Vm Vm 0V tPLH On tPHL Vm VOH Vm VOL WAVEFORM 1 - PROPAGATION DELAYS tR = tF = 2.0 ns, 10% to 90%; f = 1MHz; tW = 500 ns Figure 4. AC Waveforms http://onsemi.com 5 74ALVCH16373 VIH Vm OEn VIH Dn Vm Vm Vm 0V tPZH tPHZ VOH Vy Vm On 0V ts LEn tw Vm On tPLZ ≈ VCC tPLH, tPHL On VOH Vm Vm VOL Vx VOL WAVEFORM 3 - LE to On PROPAGATION DELAYS, LE MINIMUM PULSE WIDTH, Dn to LE SETUP AND HOLD TIMES tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns except when noted WAVEFORM 2 - OUTPUT ENABLE AND DISABLE TIMES tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns Figure 5. AC Waveforms VCC Symbol 3.3 V ±0.3 V 2.5 V ±0.2 V 1.8 V ±0.15 V VIH 2.7 V VCC VCC Vm 1.5 V VCC/2 VCC/2 Vx VOL + 0.3 V VOL + 0.15 V VOL + 0.15 V Vy VOH – 0.3 V VOH – 0.15 V VOH – 0.15 V VCC PULSE GENERATOR VIH Vm 0V ≈0V tPZL th RL DUT RT CL RL SWITCH TEST tPLH, tPHL Open tPZL, tPLZ 6 V at VCC = 3.3 ±0.3 V; VCC× 2 at VCC = 2.5 ±0.2 V; 1.8 V ±0.15 V tPZH, tPHZ GND CL = 50 pF for VCC = 3.0 ± 0.3 V RL = 500 Ω or equivalent RT = ZOUT of pulse generator (typically 50 Ω) Figure 6. Test Circuit http://onsemi.com 6 6 V or VCC × 2 OPEN GND 74ALVCH16373 AC CHARACTERISTICS (tR = tF = 2.0 ns; CL = 50 pF; RL = 500 Ω) Limits TA = –40°C to +85°C VCC = 3.0 V to 3.6 V Symbol Parameter VCC = 2.7 V Waveform Min Max Max Unit tPLH tPHL Propagation Delay Dn to On 4 1.0 1.0 3.6 3.6 Min 4.3 4.3 ns tPLH tPHL Propagation Delay LE to On 4 1.0 1.0 3.9 3.9 4.6 4.6 ns tPZH tPZL Output Enable Time to High and Low Level 5 1.0 1.0 4.7 4.7 5.7 5.7 ns tPHZ tPLZ Output Disable Time From High and Low Level 5 1.0 1.0 4.1 4.1 4.5 4.5 ns tOSHL tOSLH Output–to–Output Skew (Note 13) 0.5 0.5 0.5 0.5 ns 13. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter guaranteed by design. VCC PULSE GENERATOR RL DUT RT CL TEST RL SWITCH tPLH, tPHL Open tPZL, tPLZ 6 V at VCC = 3.3 ±0.3 V; VCC× 2 at VCC = 2.5 ±0.2 V; 1.8 V ±0.15 V tPZH, tPHZ GND CL = 50 pF or equivalent (Includes jig and probe capacitance) RL = 500 Ω or equivalent RT = ZOUT of pulse generator (typically 50 Ω) Figure 7. Test Circuit http://onsemi.com 7 6 V or VCC × 2 OPEN GND 74ALVCH16373 P0 K t P2 D TOP COVER TAPE E A0 + K0 SEE NOTE 2 B1 10 PITCHES CUMULATIVE TOLERANCE ON TAPE ±0.2 mm (±0.008") SEE NOTE 2 F + B0 W + D1 FOR COMPONENTS 2.0 mm × 1.2 mm AND LARGER P EMBOSSMENT FOR MACHINE REFERENCE ONLY INCLUDING DRAFT AND RADII CONCENTRIC AROUND B0 CENTER LINES OF CAVITY USER DIRECTION OF FEED *TOP COVER TAPE THICKNESS (t1) 0.10 mm (0.004") MAX R MIN BENDING RADIUS 10° TAPE AND COMPONENTS SHALL PASS AROUND RADIUS R" WITHOUT DAMAGE EMBOSSED CARRIER 100 mm (3.937") MAXIMUM COMPONENT ROTATION EMBOSSMENT 1 mm MAX TYPICAL COMPONENT CAVITY CENTER LINE TAPE 1 mm (0.039") MAX TYPICAL COMPONENT CENTER LINE 250 mm (9.843") CAMBER (TOP VIEW) ALLOWABLE CAMBER TO BE 1 mm/100 mm NONACCUMULATIVE OVER 250 mm Figure 8. Carrier Tape Specifications EMBOSSED CARRIER DIMENSIONS (See Notes 14 and 15) Tape Size B1 Max 24mm 20.1mm (0.791") D D1 E F K P P0 P2 R T W 1.5 + 0.1mm -0.0 (0.059 +0.004" -0.0) 1.5mm Min (0.060") 1.75 ±0.1 mm (0.069 ±0.004") 11.5 ±0.10 mm (0.453 ±0.004") 11.9 mm Max (0.468") 16.0 ±0.1 mm (0.63 ±0.004") 4.0 ±0.1 mm (0.157 ±0.004") 2.0 ±0.1 mm (0.079 ±0.004") 30 mm (1.18") 0.6 mm (0.024") 24.3 mm (0.957") 14. Metric Dimensions Govern–English are in parentheses for reference only. 15. A0, B0, and K0 are determined by component size. The clearance between the components and the cavity must be within 0.05 mm min to 0.50 mm max. The component cannot rotate more than 10° within the determined cavity. http://onsemi.com 8 74ALVCH16373 t MAX 13.0 mm ±0.2 mm (0.512" ±0.008") 1.5 mm MIN (0.06") A 20.2 mm MIN (0.795") 50 mm MIN (1.969") FULL RADIUS G Figure 9. Reel Dimensions REEL DIMENSIONS Tape Size A Max G t Max 24 mm 360 mm (14.173") 24.4 mm + 2.0 mm, -0.0 (0.961" + 0.078", -0.00) 30.4 mm (1.197") DIRECTION OF FEED BARCODE LABEL POCKET Figure 10. Reel Winding Direction http://onsemi.com 9 HOLE 74ALVCH16373 CAVITY TAPE TOP TAPE TAPE TRAILER (Connected to Reel Hub) NO COMPONENTS 160 mm MIN TAPE LEADER NO COMPONENTS 400 mm MIN COMPONENTS DIRECTION OF FEED Figure 11. Tape Ends for Finished Goods User Direction of Feed Figure 12. Reel Configuration ÉÉ ÉÉ ÉÉ ÉÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ É ÉÉ ÉÉ ÉÉ É ÉÉ É ÉÉ ÉÉ ÉÉ É ÉÉ É ÉÉ ÉÉÉÉÉÉÉÉ ÉÉ ÉÉ ÉÉÉÉ ÉÉ ÉÉÉÉ ÉÉÉ ÉÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ É ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ É ÉÉ ÉÉÉÉ ÉÉÉÉÉÉÉ K L G 48 Leads Figure 13. Package Footprint http://onsemi.com 10 F 74ALVCH16373 PACKAGE DIMENSIONS TSSOP DT SUFFIX CASE 1201–01 ISSUE A 48X ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ K K1 K REF 0.12 (0.005) M T U S V S T U S J J1 48 25 0.254 (0.010) M SECTION N–N B –U– L N 1 24 A –V– PIN 1 IDENT. N F DETAIL E D 0.076 (0.003) –T– SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSIONS A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. C M 0.25 (0.010) –W– DETAIL E G H http://onsemi.com 11 DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 12.40 12.60 6.00 6.20 --1.10 0.05 0.15 0.50 0.75 0.50 BSC 0.37 --0.09 0.20 0.09 0.16 0.17 0.27 0.17 0.23 7.95 8.25 0 8 INCHES MIN MAX 0.488 0.496 0.236 0.244 --0.043 0.002 0.006 0.020 0.030 0.0197 BSC 0.015 --0.004 0.008 0.004 0.006 0.007 0.011 0.007 0.009 0.313 0.325 0 8 74ALVCH16373 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800–282–9855 Toll Free USA/Canada http://onsemi.com 12 74ALVCH16373/D