CY7C335 Universal Synchronous EPLD Features — 2-ns input set-up and 9-ns output register clock to output • 100-MHz output registered operation • Twelve I/O macrocells, each having: — Registered, three-state I/O pins — 10-ns input register clock to state register clock • 28-pin, 300-mil DIP, LCC, PLCC • Erasable and reprogrammable • Programmable security bit — Input and output register clock select multiplexer — Feed back multiplexer • • • • • • • • • • Functional Description — Output enable (OE) multiplexer Bypass on input and output registers All twelve macrocell state registers can be hidden User configurable I/O macrocells to implement JK or RS flip-flops and T or D registers Input multiplexer per pair of I/O macrocells allows I/O pin associated with a hidden macrocell state register to be saved for use as an input Four dedicated hidden registers Twelve dedicated registered inputs with individually programmable bypass option Three separate clocks—two input clocks, two output clocks Common (pin 14-controlled) or product term-controlled output enable for each I/O pin 256 product terms—32 per pair of macrocells, variable distribution Global, synchronous, product term-controlled, state register set and reset—inputs to product term are clocked by input clock The CY7C335 is a high-performance, erasable, programmable logic device (EPLD) whose architecture has been optimized to enable the user to easily and efficiently construct very high performance state machines. The architecture of the CY7C335, consisting of the user-configurable output macrocell, bidirectional I/O capability, input registers, and three separate clocks, enables the user to design high-performance state machines that can communicate either with each other or with microprocessors over bidirectional parallel buses of user-definable widths. The four clocks permit independent, synchronous state machines to be synchronized to each other. The user-configurable macrocells enable the designer to designate JK-, RS-, T-, or D-type devices so that the number of product terms required to implement the logic is minimized. The CY7C335 is available in a wide variety of packages including 28-pin, 300-mil plastic and ceramic DIPs, PLCCs, and LCCs. Logic Block Diagram OE/I11 I10 I9 I8 I7 I6 VSS I5 14 13 12 11 10 9 8 7 I4 I3 6 5 I2 I1/CLK3 4 I0/CLK2 3 CLK1 2 1 NODE 41 NODE 42 NODE 43 PROGRAMMABLE AND ARRAY (258x68) 9 19 11 17 13 15 13 17 11 19 15 13 17 11 19 9 15 16 17 18 19 20 21 22 23 24 25 26 27 28 I/O11 I/O10 I/O9 I/O8 I/O7 I/O6 VSS VCC I/O5 I/O4 I/O3 I/O2 I/O1 I/O0 San Jose • Cypress Semiconductor Corporation Document #: 38-03017 Rev. ** • 3901 North First Street • C335–1 CA 95134 • 408-943-2600 Revised March 26, 1997 CY7C335 Pin Configurations PLCC Top View I2 I1 /CLK3 I0 /CLK2 CLk1 I/O0 I/O1 I/O 2 I2 I1 /CLK3 I0 /CLK2 CLK1 I/O0 I/O1 I/O 2 LCC Top View 4 3 2 1 2827 26 VSS I6 I7 I8 5 6 7 8 9 10 11 25 24 23 22 21 20 19 I/O3 I/O4 I/O5 VCC VSS I/O6 I/O7 I3 I4 I5 VSS I6 I7 I8 121314 1516 1718 9 10 OE/I11 I/O11 I/O10 I/O9 I 9 10 OE/I11 I/O11 I/O10 I/O9 I/O8 12131415161718 5 6 7 8 9 10 11 I I I C335–2 25 24 23 22 21 20 19 I/O8 4 3 2 1 282726 I3 I4 I5 I/O3 I/O4 I/O5 VCC VSS I/O6 I/O7 C335–3 Selection Guide Maximum Operating Frequency (MHz) Commercial ICC1 (mA) Commercial CY7C335–100 CY7C335–83 CY7C335–66 CY7C335–50 100 83.3 66.6 50 83.3 66.6 50 140 140 140 160 160 160 Military 140 Military Architecture Configuration Bits The architecture configuration bits are used to program the multiplexers. The function of the architecture bits is outlined in Table 1. Table 1. Architecture Configuration Bits Architecture Configuration Bit Number of Bits Value Function C0 Output Enable Select MUX 12 Bits, 1 Per I/O Macrocell 0—Virgin State Output Enable Controlled by Product Term 1—Programmed Output Enable Controlled by Pin 14 C1 State Register Feed Back MUX 12 Bits, 1 Per I/O Macrocell 0—Virgin State State Register Output is Fed Back to Input Array 1—Programmed I/O Macrocell is Configured as an Input and Output of Input Path is Fed to Array I/O Macrocell Input Register Clock Select MUX 12 Bits, 1 Per I/O Macrocell 0—Virgin State ICLK1 Controls the Input Register I/O Macrocell Input Register Clock Input 1—Programmed ICLK2 Controls the Input Register I/O Macrocell Input Register Clock Input C3 Input Register Bypass MUX— I/O Macrocell 12 Bits, 1 Per I/O Macrocell 0—Virgin State Selects Input to Feedback MUX from Input Register 1—Programmed Selects Input to Feedback MUX from I/O pin C4 Output Register Bypass MUX 12 Bits, 1 Per I/O Macrocell 0—Virgin State Selects Output from the State Register 1—Programmed Selects Output from the Array, Bypassing the State Register State Clock MUX 16 Bits, 1 Per I/O Macrocell and 1 Per Hidden Macrocell 0—Virgin State State Clock 1 Controls the State Register 1—Programmed State Clock 2 Controls the State Register C2 C5 Document #: 38-03017 Rev. ** Page 2 of 18 CY7C335 Table 1. Architecture Configuration Bits (continued) Architecture Configuration Bit C6 C7 C8 C9 C10 CX (11–16) Number of Bits Value Function Dedicated Input Register Clock Select MUX 12 Bits, 1 Per Dedicated Input Cell 0—Virgin State ICLK1 Controls the Input Register I/O Macrocell Dedicated Input Register Clock Input 1—Programmed ICLK2 Controls the Input Register I/O Macrocell Dedicated Input Register Clock Input Input Register Bypass MUX— Input Cell 12 Bits, 1 Per Dedicated Input Cell 0—Virgin State Selects Input to Array from Input Register 1—Programmed Selects Input to Array from Input Pin ICLK2 Select MUX 1 Bit 0—Virgin State Input Clock 2 Controlled by Pin 2 1—Programmed Input Clock 2 Controlled by Pin 3 ICLK1 Select MUX 1 Bit 0—Virgin State Input Clock 1 Controlled by Pin 2 1—Programmed Input Clock 1 Controlled by Pin 1 SCLK2 Select MUX 1 Bit 0—Virgin State State Clock 2 Grounded 1—Programmed State Clock 2 Controlled by Pin 3 I/O Macrocell Pair Input Select MUX 6 Bits, 1 Per I/O Macrocell Pair 0—Virgin State Selects Data from I/O Macrocell Input Path of Macrocell A of Macrocell Pair 1—Programmed Selects Data from I/O Macrocell Input Path of Macrocell B of Macrocell Pair 1 INPUTREGISTER 0 INPUT PIN ICLK1 ICLK2 D Q INPUT REG BYPASS MUX TO ARRAY C7 0 INPUT CLOCK 1 MUX C6 C335–4 Figure 1. CY7C335 Input Macrocell Document #: 38-03017 Rev. ** Page 3 of 18 CY7C335 C0 PIN 14: OE OUTPUT ENABLE PRODUCT TERM OUTPUT REG BYPASS MUX 1 OUTPUT ENABLE 0 MUX C4 SET PRODUCT TERM 1 EX OR PRODUCT TERM I/O PIN S Q D 0 0 SCLK1 STATE CLK 1 MUX SCLK2 R Q C5 RESET PRODUCT TERM TO ARRAY 0 FEED BACK MUX 1 C2 C1 INPUT REG BYPASS MUX 1 INPUT REGISTER 0 D 0 ICLK1 INPUT CLOCK 1 MUX ICLK2 C3 C335–5 0 TO ARRAY Q SHARED INPUT MUX CX (11 – 16) 1 FROM ADJACENT MACROCELL Figure 2. CY7C335 Input/Output Macrocell Document #: 38-03017 Rev. ** Page 4 of 18 CY7C335 SET PRODUCT TERM S Q D SCLK1 SCLK2 0 1 STATE CLK MUX R Q C5 RESET PRODUCT TERM TO ARRAY C335–6 Figure 3. CY7C335 Hidden Macrocell SCLK2 TO OUTPUT MACROCELLS AND HIDDEN MACROCELLS PIN 1 1 0 SCLK1 TO OUTPUT MACROCELLS AND HIDDEN MACROCELLS ICLK1 ICLK2 MUX 1 0 C9 PIN 2 TO ARRAY MUX 1 0 MUX 0 1 MUX C8 1 0 PIN 3 TO ARRAY MUX 1 0 MUX 1 0 MUX C10 C335–7 Figure 4. CY7C335 Input Clocking Scheme Document #: 38-03017 Rev. ** Page 5 of 18 CY7C335 Maximum Ratings Static Discharge Voltage ........................................... >2001V (per MIL-STD-883, Method 3015) (Above which the useful life may be impaired. For user guidelines, not tested.) Latch-Up Current..................................................... >200 mA Storage Temperature ...................................–65°C to +150°C DC Programming Voltage............................................. 13.0V Ambient Temperature with Power Applied...............................................–55°C to +125°C Operating Range Range Ambient Temperature VCC Commercial 0°C to +75°C 5V ± 10% Industrial –40°C to +85°C 5V ± 10% Military[1] –55°C to +125°C 5V ± 10% Supply Voltage to Ground Potential (Pin 22 to Pins 8 and 21) ............................... –0.5V to +7.0V DC Voltage Applied to Outputs in High Z State ............................................... –0.5V to +7.0V DC Input Voltage............................................ –3.0V to +7.0V Output Current into Outputs (Low)...............................12 mA Electrical Characteristics Over the Operating Range[2] Parameter VOH Description Output HIGH Voltage Test Conditions VCC = Min., VIN = VIH or VIL IOH = –3.2 mA IOL = 12 mA Min. Com’l Max. Unit 2.4 V Mil/Ind VOL Output LOW Voltage VCC = Min., VIN = VIH or VIL VIH Input HIGH Level Guaranteed Input Logical HIGH Voltage for All Inputs[3] VIL Input LOW Level [3] Guaranteed Input Logical LOW Voltage for All Inputs IIX Input Leakage Current VSS ≤ VIN ≤ VCC, VCC = Max. –10 IOZ Output Leakage Current VCC = Max., VSS ≤ VOUT ≤ VCC –40 40 µA ISC Output Short Circuit Current VCC = Max., VOUT = 0.5V[4, 5] –30 –90 mA ICC1 Standby Power Supply Current VCC = Max., VIN = GND Outputs Open Com’l 140 mA Mil/Ind 160 mA Power Supply Current at Frequency[5] VCC = Max., Outputs Disabled (in High Z State), Device Operating at fMAX External (fMAX5) Com’l 180 mA Mil/Ind 200 mA ICC2 Com’l 0.5 V Mil/Ind 2.2 V 0.8 V 10 µA Capacitance[5] Parameter Description Test Conditions Min. Max. Unit CIN Input Capacitance VIN = 2.0V @ f = 1 MHz 10 pF COUT Output Capacitance VOUT = 2.0V @ f = 1 MHz 10 pF Notes: 1. tA is the “instant on” case temperature. 2. See the last page of this specification for Group A subgroup testing information. 3. These are absolute values with respect to device ground and all overshoots due to system or tester noise are included. 4. Not more than one output should be tested at a time. Duration of the short circuit should not be more than one second. VOUT = 0.5V has been chosen to avoid test problems caused by ground degradation. 5. Tested initially and after any design or process changes that may affect these parameters. Document #: 38-03017 Rev. ** Page 6 of 18 CY7C335 AC Test Loads and Waveforms (Commercial) R1 313 Ω (470Ω MIL/IND) 5V ALL INPUT PULSES 3.0V OUTPUT 90% R2 208 Ω (319Ω Mil/Ind) 50pF GND INCLUDING JIG AND SCOPE ≤ 3 ns C335–8 R=125 Ω (190Ω MIL) R=125 Ω (190Ω MIL) OUTPUT VTH =2.00V (2.02VMIL) C = 50 pF 0V 0V C = 5 pF Parameter VX t PXZ (–) 1.5V t CER (–) t CER (+) t CEA (+) t CEA (–) 2.6V V th V th 1.5V 2.6V V th V th VX 0V C335–9 (c) Thévenin Equivalent (Load 1) t PZX (–) C335–11 (b) OUTPUT t PZX (+) 10% ≤ 3 ns (a) t PXZ (+) 90% 10% 0V C335–10 (d) Three-state Delay Load (Load2) Output Waveform Measurement Level V OH 0.5V V OL V OH 0.5V VX V OH C335–14 0.5V V OL C335–15 0.5V VX C335–16 0.5V V OL VX C335–17 0.5V VX VX C335–12 C335–13 VX VX VX 0.5V V OH C335–18 0.5V V OL C335–19 Figure 5. Test Waveforms Document #: 38-03017 Rev. ** Page 7 of 18 CY7C335 Commercial AC Characteristics 7C335–100 Parameter Description 7C335–83 7C335–66 7C335–50 Min. Max. Min. Max. Min. Max. Min. Max. Unit Combinatorial Mode Parameters tPD Input to Output Propagation Delay 15 15 20 25 ns tEA Input to Output Enable 15 15 20 25 ns tER Input to Output Disable 15 15 20 25 ns Input Registered Mode Parameters tWH Input and Output Clock Width HIGH[5] 4 5 6 8 ns tWL Input and Output Clock Width LOW [5] 4 5 6 8 ns tIS Input or Feedback Set-Up Time to Input Clock 2 2 2 3 ns tIH Input Register Hold Time from Input Clock 2 tICO Input Register Clock to Output Delay tIOH Output Data Stable Time from Input Clock 3 3 3 3 ns tIOH – tIH 33x Output Data Stable from Input Clock Minus Input Register Hold Time for 7C335[6] 0 0 0 0 ns tPZX Pin 14 Enable to Output Enabled tPXZ Pin 14 Disable to Output Disabled fMAX1 Maximum Frequency of (2) CY7C335s in Input Registered Mode (Lowest of 1/(tICO +tIS) & 1/(tWL +tWH))[5] 50 50 45.4 35.7 MHz fMAX2 Maximum Frequency Data Path in Input Registered Mode (Lowest of (1/(tICO), 1/(tWH +tWL), 1/(tIS +tIH))[5] 55.5 55.5 50 40 MHz tICEA Input Clock to Output Enabled 17 17 20 25 ns tICER Input Clock to Output Disabled 15 15 20 25 ns 2 18 2 18 12 12 12 3 20 15 12 ns 25 20 15 20 ns ns ns Output Registered Mode Parameters tCEA Output Clock to Output Enabled[5] 17 17 20 25 ns tCER Output Clock to Output Disabled[5] 15 15 20 25 ns tS Output Register Input Set-Up Time from Output Clock 8 tH Output Register Input Hold Time from Output Clock 0 tCO Output Register Clock to Output Delay 9 10 12 15 ns tCO2 Input Output Register Clock or Latch Enable to Combinatorial Output Delay (Through Logic Array)[5] 17 18 23 30 ns tOH Output Data Stable Time from Output Clock 2 2 2 2 ns tOH2 Output Data Stable Time From Output Clock (Through Memory Array)[5] 3 3 3 3 ns tOH2–tIH Output Data Clock Stable Time From Output Clock Minus Input Register Hold Time[5] 0 0 0 0 ns fMAX3 Maximum Frequency with Internal Feedback in Output Registered Mode[5] 100 83.3 66.6 50 MHz fMAX4 Maximum Frequency of (2) CY7C335s in Output Registered Mode (Lowest of 1/(tCO + tS) & 1/(tWL + tWH))[5] 58.8 50 41.6 33.3 MHz fMAX5 Maximum Frequency Data Path in Output Registered Mode (Lowest of 1/(tCO), 1/(tWL + tWH), 1/(tS + tH))[5] 111 100 83.3 62.5 MHz tOH – tIH 33x Output Data Stable from Output Clock Minus Input Register Hold Time for 7C335[6] 0 0 0 0 ns Document #: 38-03017 Rev. ** 9 12 0 15 0 ns 0 ns Page 8 of 18 CY7C335 Commercial AC Characteristics (continued) 7C335–100 Parameter Description 7C335–83 7C335–66 7C335–50 Min. Max. Min. Max. Min. Max. Min. Max. Unit Pipelined Mode Parameters tCOS Input Clock to Output Clock 10 12 15 20 ns fMAX6 Maximum Frequency Pipelined Mode (Lowest of 1/(tCOS), 1/(tCO), 1/(tWL + tWH)), 1/(tIS + tIH)[5] 100 83.3 66.6 50 MHz fMAX7 Maximum Frequency of (2) CY7C335s in Pipelined Mode (Lowest of 1/(tCO + tIS) or 1/tCOS) 90.9 83.3 66.6 50 MHz Power-Up Reset Parameters tPOR Power-Up Reset Time[5, 7] 1 1 1 1 µs Military/Industrial AC Characteristics 7C335–83 Parameter Description Min. Max. 7C335–66 Min. Max. Unit Combinatorial Mode Parameters tPD Input to Output Propagation Delay 20 20 ns tEA Input to Output Enable 20 20 ns tER Input to Output Disable 20 20 ns Input Registered Mode Parameters tWH Input and Output Clock Width HIGH[5] 5 6 ns tWL Input and Output Clock Width LOW[5] 5 6 ns tIS Input or Feedback Set-Up Time to Input Clock 3 3 ns tIH Input Register Hold Time from Input Clock 3 3 ns tICO Input Register Clock to Output Delay tIOH Output Data Stable Time from Input Clock 3 3 ns tIOH – tIH 33x Output Data Stable from Input Clock Minus Input Register Hold Time for 7C335[6] 0 0 ns tPZX Pin 14 Enable to Output Enabled 15 15 ns tPXZ Pin 14 Disable to Output Disabled 15 15 ns fMAX1 Maximum Frequency of (2) CY7C335s in Input Registered Mode (Lowest of 1/(tICO +tIS) & 1/(tWL +tWH))[5] 38.4 38.4 MHz fMAX2 Maximum Frequency Data Path in Input Registered Mode (Lowest of (1/(tICO), 1/(tWH +tWL), 1/(tIS +tIH))[5] 43.4 43.4 MHz tICEA Input Clock to Output Enabled 20 20 ns tICER Input Clock to Output Disabled 20 20 ns 20 20 ns 20 ns 23 23 ns Output Registered Mode Parameters tCEA Output Clock to Output Enabled [5] tCER Output Clock to Output Disabled [5] tS Output Register Input Set-Up Time to Output Clock 10 tH Output Register Input Hold Time from Output Clock 0 tCO Output Register Clock to Output Delay 11 12 ns tCO2 Output Register Clock or Latch Enable to Combinatorial Output Delay (Through Logic Array)[5] 22 23 ns 20 12 ns 0 ns Notes: 6. This specification is intended to guarantee interface compatibility of the other members of the CY7C330 family with the CY7C335. This specification is met for the devices operating at the same ambient temperature and at the same power supply voltage. 7. This part has been designed with the capability to reset during system power-up. Following power-up, the input and output registers will be reset to a logic LOW state. The output state will depend on how the array is programmed. Document #: 38-03017 Rev. ** Page 9 of 18 CY7C335 Military/Industrial AC Characteristics (continued) 7C335–83 Parameter Description Min. tOH Output Data Stable Time from Output Clock tOH2 Output Data Stable Time From Output Clock Memory Array)[5] tOH2–tIH Output Data Clock Stable Time From Output Clock Minus Input Register Hold Time[5] fMAX3 Max. 7C335–66 Min. Max. Unit 2 2 ns 3 3 ns 0 0 ns Maximum Frequency with Internal Feedback in Output Registered Mode[5] 83.3 66.6 MHz fMAX4 Maximum Frequency of (2) CY7C335s in Output Registered Mode (Lower of 1/(tCO + tS) & 1/(tWL + tWH))[5] 47.6 41.6 MHz fMAX5 Maximum Frequency Data Path in Output Registered Mode (Lowest of 1/(tCO), 1/(tWL + tWH), 1/(tS + tH))[5] 90.9 83.3 MHz tOH – tIH 33x Output Data Stable from Output Clock Minus Input Register Hold Time for 7C335[6] 0 0 ns 12 15 ns (Through Pipelined Mode Parameters tCOS Input Clock to Output Clock fMAX6 Maximum Frequency Pipelined Mode (Lowest of 1/(tCOS), 1/(tIS), or 1/(tCO)), 1/(tIS + tIH)[5] 83.3 66.6 MHz fMAX7 Maximum Frequency of (2) CY7C335s in Pipelined Mode (Lowest of 1/(tCO + tIS) or 1/tCOS) 71.4 66.6 MHz Power-Up Reset Parameters tPOR Power-Up Reset Time[5, 7] Document #: 38-03017 Rev. ** 1 1 µs Page 10 of 18 CY7C335 Switching Waveform INPUTOR I/O PIN tIS tIH tS tH INPUT REG. CLOCK tWH tWL tCOS tWH tWL tICO OUTPUT REG. CLOCK tCO tOH tIOH OUTPUT tPD tEA tICER tICEA tER tPXZ tPZX PIN 14 AS OE C335–20 Power-Up Reset Waveform[7] 90% VCC tPOR OUTPUT tCOS CLOCK tWL C335–21 Document #: 38-03017 Rev. ** Page 11 of 18 CY7C335 Block Diagram (Page 1 of 2) 1 (C9) SCLK2 SCLK1 0 8 16 24 32 40 48 56 64 RESET node=29 2 (C6,7) (C8) 9 (C10) 3 (C6,7) 28 node=40 ICLK2 ICLK1 19 11 4 (C6,7) 27 26 node=39 17 13 5 (C6,7) 25 24 node=38 15 19 6 (C6,7) 11 23 node=34 node=33 7 (C6,7) TO LOWER SECTION Document #: 38-03017 Rev. ** Page 12 of 18 CY7C335 Block Diagram (Page 2 of 2) TO UPPER SECTION 15 20 9 node=37 (C4,5) 13 19 17 node=32 10 (C4,5) 13 node=31 11 (C4,5) 17 18 12 node=36 (C4,5) 11 17 13 (C4,5) 19 16 14 node=35 (C4,5) 9 OE 0 8 16 24 32 40 48 56 64 SET 15 node=30 OE C335–23 Document #: 38-03017 Rev. ** Page 13 of 18 CY7C335 Ordering Information fMAX (MHz) ICC1 (mA) 100 140 CY7C335–100WC 83.3 160 Ordering Code 50 Package Type Operating Range W22 28-Lead (300-Mil) Windowed CerDIP Commercial CY7C335–83LMB L64 28-Square Leadless Chip Carrier Military CY7C335–83QMB Q64 28-Pin Windowed Leadless Chip Carrier CY7C335–83WMB W22 28-Lead (300-Mil) Windowed CerDIP CY7C335–83HC H64 28-Pin Windowed Leaded Chip Carrier CY7C335–83JC J64 28-Lead Plastic Leaded Chip Carrier CY7C335–83WC W22 28-Lead (300-Mil) Windowed CerDIP 160 CY7C335–66QMB Q64 28-Pin Windowed Leadless Chip Carrier Military 140 CY7C335–66HC H64 28-Pin Windowed Leaded Chip Carrier Commercial CY7C335–66JC J64 28-Lead Plastic Leaded Chip Carrier CY7C335–66PC P21 28-Lead (300-Mil) Molded DIP CY7C335–66WC W22 28-Lead (300-Mil) Windowed CerDIP CY7C335–50JC J64 28-Lead Plastic Leaded Chip Carrier CY7C335–50PC P21 28-Lead (300-Mil) Molded DIP 140 66.6 Package Name 140 Commercial MILITARY SPECIFICATIONS Group A Subgroup Testing DC Characteristics Parameter Switching Characteristics Subgroups Parameter Subgroups VOH 1, 2, 3 tPD 9, 10, 11 VOL 1, 2, 3 tICO 9, 10, 11 VIH 1, 2, 3 tIS 9, 10, 11 VIL 1, 2, 3 tCO 9, 10, 11 IIX 1, 2, 3 tS 9, 10, 11 IOZ 1, 2, 3 tH 9, 10, 11 ICC 1, 2, 3 tCOS 9, 10, 11 Document #: 38-03017 Rev. ** Page 14 of 18 CY7C335 Package Diagrams 28-Lead (300-Mil) CerDIP D22 MIL-STD-1835 28-Square Leadless Chip Carrier L64 MIL-STD-1835 C–4 Document #: 38-03017 Rev. ** 28-Lead Plastic Leaded Chip Carrier J64 D–15 Config.A 28-Pin Windowed Leadless Chip Carrier Q64 MIL-STD-1835 C–4 Page 15 of 18 CY7C335 Package Diagrams (continued) 28-Pin Windowed Leaded Chip Carrier H64 Document #: 38-03017 Rev. ** Page 16 of 18 CY7C335 Package Diagrams (continued) 28-Lead (300-Mil) Molded DIP P21 28-Lead (300-Mil) Windowed CerDIP W22 MIL-STD-1835 Document #: 38-03017 Rev. ** D– 15Config.A Page 17 of 18 © Cypress Semiconductor Corporation, 1997. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C335 Document Title: CY7C335 Universal Synchronous EPLD Document Number: 38-03017 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 106317 04/30/01 SZV Change from Spec number: 38-00186 to 38-03017 Document #: 38-03017 Rev. ** Page 18 of 18