R07 Miniature Series 07 General Purpose Regulator 1/8" and 1/4" Port Sizes ● Compact design ● Full flow gauge ports ● Low torque, non-rising adjusting knob ● Snap action knob locks pressure setting when pushed in ● Standard relieving models allow reduction of outlet pressure even when the system is dead-ended ● Can be disassembled without the use of tools or removal from the air line Technical Data Ordering Information Fluid: Compressed air Maximum pressure: 20 bar (300 psig) Operating temperature: -20° to +65°C (0° to +150°F) * See Ordering Information on the following pages. * Air supply must be dry enough to avoid ice formation at temperatures below +2°C (+35°F). Typical flow at 10 bar (145 psig) inlet pressure, 6,3 bar (90 psig) set pressure and a droop of 1 bar (14.5 psig) from set: 1/8" ports: 6,5 dm3/s (14 scfm) 1/4" ports: 7 dm3/s (15 scfm) Gauge ports: 1/8" PTF with PTF main ports 1/8" ISO Rc with ISO Rc main ports 1/8" ISO Rc with ISO G main ports Materials: Body: Zinc Bonnet: Acetal Valve: Brass/nitrile Valve seat: Acetal Elastomers: Nitrile 1/97 ISO Symbols Relieving Our policy is one of continuous research and development. We reserve the right to amend, without notice, the specifications given in this document. Relieving N/AL.8.300.200.01 R07 Typical Performance Characteristics PORT SIZE: 1/4" RANGE: 0,3 to 7 bar (5 to 100 psi) psig bar g FLOW CHARACTERISTICS INLET PRESSURE: 10 bar g (145 psig) 8 OUTLET PRESSURE 100 6 80 60 4 40 2 20 0 0 0 0 2 4 4 8 6 12 8 10 16 20 dm3/s 24 scfm AIR FLOW Ordering Information. Models listed are include ISO G threads, relieving diaphragm, 0,3 to 7 bar (5 to 100 psig) outlet pressure adjustment range* without gauge. Port Size G1/8 G1/4 Model Number R07-100-RNKG R07-200-RNKG Flow† dm3/s (scfm) 6,5 (14) 7 (15) Weight kg (lbs) 0,19 (0.31) 0,19 (0.31) † Approximate flow at 7 bar (100 psig) inlet pressure, 6.3 bar (90 psig) set pressure and a droop of 1 bar (14.5 psig) from set. Alternative Models R 0 7 - ★★ ★ - ★★★★ Port Size 1/8" 1/4" Substitute 1 2 Option Not applicable Substitute 0 Option Standard Low flow seat H.P. unit, 10 bar (145 psig) Substitute 0 2 5** Threads PTF ISO Rc taper ISO G parallel Substitute A B G Outlet Pressure Adjustment Ranges* Substitute 0,1 to 0,7 bar (1 to 10 psig) A 0,3 to 3,5 bar (5 to 50 psig) E 0,3 to 7 bar (5 to 100 psig) K 0,3 to 10 bar (5 to 145 psig) M** * Outlet pressure can be adjusted to pressures in excess of, and less than, those specified. Do not use these units to control pressures outside of the specified ranges. ** When specifying 10 bar (145 psig) unit, eg. R07-205-RNMG, also note correct code at 6th digit. Gauges With Without Substitute G N Diaphragm Relieving Non relieving Substitute R N Accessories Wall Mounting Bracket and Panel Nut for P1H Unit Plastic: 18-025-003 N/AL.8.300.200.02 Panel Nut Tamper Resistant Field Modification Ø 40 mm Pressure Gauge Plastic: 2962-89 Metal: 2962-04 Knob and screw: 18-001-092 Screw only: 6097-08 2 bar (30 psig): 4 bar (60 psig): 10 bar (150 psig): 25 bar (350 psig): R1/8 Connection 1/8" PTF Connection Our policy is one of continuous research and development. We reserve the right to amend, without notice, the specifications given in this document. — 18-013-990 18-013-989 18-013-908 18-013-214 18-013-211 18-013-212 — 1/97 R07 Dimensions mm (inches) Panel mounting hole diameter 30 mm (1.19") Maximum panel thickness 0 to 6 mm (0 to 0.25") 41 (1.63) 54 (2.13) 38 (1.50) 23 19 (0.73) (0.91) 40 (1.57) 75 (2.91) 64 (2.52) 24 (0.95) 28 (1.1) Bracket Mounting Bracket Kit Reference Use 3 mm (1/8") screws to mount bracket to wall. Part Number 18-025-003 63 (2.47) 28 to 44 (1.09 to 1.73) Item All models 38 (1.50) 24 (0.93) 42 (1.65) 6 (0.22) 34 (1.34) 7 (0.29) Service Kits Item Service kit Type Relieving Non-relieving Part number 3407-02 3407-01 Service kit includes slip ring, diaphragm, standard valve seat with o-ring, valve, valve spring. 1/97 Our policy is one of continuous research and development. We reserve the right to amend, without notice, the specifications given in this document. N/AL.8.300.200.03 R07 Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NORGREN. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. Water vapor will pass through these units and will condense into liquid if air temperature drops in the downstream system. Install an air dryer if water condensation could have a detrimental effect on the application. N/AL.8.300.200.04 Our policy is one of continuous research and development. We reserve the right to amend, without notice, the specifications given in this document. 1/97