UC5180C Octal Line Receiver FEATURES DESCRIPTION • Meets EIA 232E/423A/422A and CCITT V.10,V.11, V.28, X.26, X.27 • Single +5V Supply--TTL Compatible Outputs • Differential Inputs Withstand ± 25V • Low Open Circuit Voltage for Improved Failsafe Characteristic The UC5180C is an octal line receiver designed to meet a wide range of digital communications requirements as outlined in EIA standards EIA232E, EIA423A, EIA422A, and CCITT V.10, V.11, V.28, X.26, and X.27. The UC5180C includes an input noise filter and is intended for applications employing data rates up to 200 KBPS. A failsafe function allows these devices to "fail" to a known state under a wide variety of fault conditions at the inputs. • Reduced Supply Current--35 mA Max • Input Noise Filter • Internal Hysteresis ABSOLUTE MAXIMUM RATINGS (Note 1) Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Output Sink Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Output Short Circuit Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Sec Common Mode Input Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V Differential Input Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V Failsafe Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to VCC PLCC Power Dissipation, TA = 25°C (Note 2). . . . . . . . . . . . . . . . . . . 1000 mW DIP Power Dissipation, TA = 25°C (Note 2) . . . . . . . . . . . . . . . . . . . . 1200 mW Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C Lead Temperature (Soldering, 10 Seconds) . . . . . . . . . . . . . . . . . . . . . . -300°C Note 1: All voltages are with respect to ground, pin 14. Currents are positive into, negative out of the specified terminal Note 2: Consult Packaging Section of Databook for thermal limitations and considerations of package. CONNECTION DIAGRAMS DIL-28 (TOP VIEW) 1/94 Powered by ICminer.com Electronic-Library Service CopyRight 2003 PLCC-28 (TOP VIEW) UC5180C DC ELECTRICAL CHARACTERISTICS: Unless otherwise stated these specifications apply for TA = 0°C to +70°C, VCC = 5V ± 5%, Input Common Mode Range ± 7V, TA =TJ PARAMETERS SYMBOL TEST CONDITIONS DC Input Resistance Failsafe Output Voltage RIN VOFS Differential Input High Threshold VTH Differential Input Low Threshold VTL Hysteresis Open Circuit Input Voltage Input Capacitance VH VICC CI High Level Output Voltage Low Level Output Voltage VCH VOL VID = 1V, IOUT = - 440µA VID = -1V (Note 3) Short Circuit Output Current Supply Current Input Current IOS Note 4 ICC IIN 4.75V ≤ VCC ≤ 5.25V Other Inputs Grounded UC5180C MIN MAX 3 7 0.45 2.7 3V ≤ | VIN | ≤ 25V Inputs Open or Shorted Together, or One Input Open and One Grounded 0 ≤ IOUT ≤ 8mA, VFAILSAFE = 0V 0 ≥ IOUT ≥ - 400 µA, VFAILSAFE = VCC VOUT = 2.7V, IOUT = 440 µA RS = 0 (Note 2) (See Figure 1) RS = 500 (Note 2) VOUT = 0.45V, IOUT = 440 mA RS = 0 (Note 2) (See Figure 1) RS = 500 (Note 2) FS = 0V or VCC (See Figure 1) 50 -200 -400 50 20 VIN = +10V VIN = -10V kΩ V 200 400 -50 mV 140 75 20 mV mV pF 2.7 IOUT = 4 mA IOUT = 8 mA UNITS mV V V 0.4 0.45 100 mA 35 3.25 mA mA -3.25 Note 2: RS is a resistor in series with each input. Note 3: Measured after 100ms warm up (at 0°C) Note 4: Only 1 output may be shorted at one time and then only for a maximum of 1 sec. Figure 1. VtL, VtH, VH Definition AC ELECTRICAL CHARACTERISTICS: VCC = 5V ± 5%, TA = 0°C to + 70°C, Figure 2, TA = TJ. PARAMETERS SYMBOL Propagation Delay - Low to High Propagation Delay - High to Low Acceptance Input Frequency Rejectable Input Frequency Powered by ICminer.com Electronic-Library Service CopyRight 2003 tPLH tPHL fA fR TEST CONDITIONS CL = 50pF, VIN = ± 500mV CL = 50pF, VIN = ± 500mV Unused Input Grounded, VIN = ± 200mV Unused Input Grounded, VIN = ± 500mV 2 UC5180C MIN MAX 550 550 0.1 5.5 UNITS ns ns MHz MHz UC5180C Figure 2. AC Test Circuit APPLICATIONS INFORMATION under fault conditions, while a connection to ground provides a logic "0". There are two failsafe pins (FS1 and FS2) on the UC5180C where each provides common failsafe control for four receivers. Failsafe Operation These devices provide a failsafe operating mode to guard against input fault conditions as defined in EIA422A and EIA423A standards. These fault conditions are (1) drive in power-off condition, (2) receiver not interconnected with driver, (3) open-circuited interconnecting cable, and (4) short-circuited interconnecting cable. If one of these four fault conditions occurs at the inputs of a receiver, then the output of that receiver is driven to a known logic level. The receiver is programmed by connecting the failsafe input to VCC or ground. A connection to VCC provides a logic "1" output Input Filtering (UC5180C) The UC5180C has input filtering for additional noise rejection. This filtering is a function of both signal level and frequency. For the specified input (5.5 MHz at ±500 mV) the input stage filter attenuates the signal such that the output stage threshold levels are not exceeded and no change of state occurs at the output. EIA232E/V.28 / EIA423A/V.10 DATA TRANSMISSION EIA422A/V.11 DATA TRANSMISSION UNITRODE INTEGRATED CIRCUITS 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 • FAX (603) 424-3410 Powered by ICminer.com Electronic-Library Service CopyRight 2003 3 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated Powered by ICminer.com Electronic-Library Service CopyRight 2003