Pneumatic Function Fittings Metric & Inch Pressure Sensor Fitting ● Very compact units ● Easy tube insertion for rapid assembly of pneumatic circuits ● Positive tube anchorage ● Simpler pneumatic systems ● Eliminates need for electrical reed switches Technical Data Ordering Information To order, quote appropriate product number from the tables on the following pages. Medium: Compressed air Operating Pressure: Cylinder pressure (Pc) 10 bar max Sensor supply pressure 3 - 10 bar Sensor switch pressure 1.0 bar typ. Operating Temperature: –20°C to +80°C Product numbering system is designed to make identification and selection simple: 1 Body Ports 4mm Push-in Fittings 5⁄ 32’’ Push-in Fittings 1⁄ 8, 1⁄ 4 BSPP Banjo Bolt 1⁄ 8, 1⁄ 4 NPTF Banjo Bolt 0 Shape Series Number Type Thread Size/ Tube Size Tube Size/ Thread Size Tube Sizes 4mm O/D 5⁄ 32’’ O/D Tubing Types: Nylon 11 or 12, polyurethane and other plasticised or unplasticised tubing which conforms to the tolerances specified in BS 5409, Part 1, 1976, light and normal duty, DIN 73378, DIN 74234, NFE 49-100 102GD 124GD Materials Delrin 100 and plastic parts Glass filled nylon Nickel plated brass collet Nitrile and polyurethane elastomeric parts Nickel plated brass banjo bolt 06/97 Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. N/AL 9.11.001.01 Pneumatic Function Fittings Pressure Sensor Fitting- 102GD PIF x BSPP Banjo Bolt Product number A O/D tube 102GD0418 4 102GD0428 4 D J A 1 I F H 2 A E B thread BSPP C D 1⁄8" 8,5 10,5 45,2 47,2 1⁄4" E F thread BSPP 1⁄8" 9,5 1⁄4" 9,5 G H I J A/F 5,6 6,5 21,0 21,0 24,9 29,0 15 19 This sensor fitting produces an end of stroke signal when exhaust back pressure in a cylinder decays below a set value. It should be mounted directly on the cylinder and can be used with a flow control device mounted into the top port. G It is recommended that the sensor supply pressure to port 1 be the same as the nominal working pressure of the cylinder. B C Pressure Sensor Fitting- 124GD PIF x NPTF Banjo Bolt D J A 1 I F H 2 A E Product number A O/D tube B thread NPTF C D E thread NPTF F G H I J A/F 124GD0218 124GD0228 5⁄32" 1⁄8" 45,2 47,2 9,5 9,5 9,5 14,3 21,0 21,0 28,5 33,7 9⁄16" 1⁄4" 8,5 10,5 1⁄8" 5⁄32" 1⁄4" 3⁄4" This sensor fitting produces an end of stroke signal when exhaust back pressure in a cylinder decays below a set value. It should be mounted directly on the cylinder and can be used with a flow control device mounted into the top port. G It is recommended that the sensor supply pressure to port 1 be the same as the nominal working pressure of the cylinder. B C Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable. N/AL 9.11.001.02 Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. 06/97