M PIC16C62B/72A 28-Pin 8-Bit CMOS Microcontrollers Pin Diagram • High-performance RISC CPU • Only 35 single word instructions to learn • All single cycle instructions except for program branches which are two cycle • Operating speed: DC - 20 MHz clock input DC - 200 ns instruction cycle • 2K x 14 words of Program Memory, 128 x 8 bytes of Data Memory (RAM) • Interrupt capability (up to 7 internal/external interrupt sources) • Eight level deep hardware stack • Direct, indirect, and relative addressing modes • Power-on Reset (POR) • Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) • Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation • Brown-out detection circuitry for Brown-out Reset (BOR) • Programmable code-protection • Power saving SLEEP mode • Selectable oscillator options • Low-power, high-speed CMOS EPROM technology • Fully static design • In-Circuit Serial Programming • Wide operating voltage range: 2.5V to 5.5V • High Sink/Source Current 25/25 mA • Commercial, Industrial and Extended temperature ranges • Low-power consumption: - < 2 mA @ 5V, 4 MHz - 22.5 µA typical @ 3V, 32 kHz - < 1 µA typical standby current 1998 Microchip Technology Inc. SDIP, SOIC, SSOP, Windowed CERDIP •1 28 RB7 RA0/AN0 2 27 RB6 RA1/AN1 3 26 RB5 RA2/AN2 4 25 RB4 RA3/AN3/VREF 5 24 RB3 RA4/T0CKI 6 23 RB2 RA5/SS/AN4 VSS 7 8 22 21 RB1 RB0/INT OSC1/CLKIN 9 20 VDD 19 VSS 18 RC7 MCLR/VPP PIC16C72A Microcontroller Core Features: OSC2/CLKOUT 10 RC0/T1OSO/T1CKI 11 RC1/T1OSI 12 17 RC6 RC2/CCP1 13 16 RC5/SDO RC3/SCK/SCL 14 15 RC4/SDI/SDA Peripheral Features: • Timer0: 8-bit timer/counter with 8-bit prescaler • Timer1: 16-bit timer/counter with prescaler, can be incremented during sleep via external crystal/clock • Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler • Capture, Compare, PWM module • Capture is 16-bit, max. resolution is 12.5 ns, Compare is 16-bit, max. resolution is 200 ns, PWM maximum resolution is 10-bit • 8-bit multi-channel Analog-to-Digital converter • Synchronous Serial Port (SSP) with Enhanced SPI and I2C Preliminary DS35008A-page 1 PIC16C62B/72A Pin Diagrams SDIP, SOIC, SSOP, Windowed CERDIP 28 RB7 2 27 RB6 RA1 3 26 RB5 RA2 4 25 RB4 RA3 5 24 RB3 RA4/T0CKI 6 23 RB2 RA5/SS VSS 7 8 22 21 RB1 RB0/INT OSC1/CLKIN 9 PIC16C62B •1 RA0 MCLR/VPP 20 VDD 19 VSS 18 RC7 17 RC6 13 16 RC5/SDO 14 15 RC4/SDI/SDA OSC2/CLKOUT 10 RC0/T1OSO/T1CKI 11 RC1/T1OSI 12 RC2/CCP1 RC3/SCK/SCL Key Features PICmicro™ Mid-Range Reference Manual (DS33023) PIC16C62B PIC16C72A Operating Frequency DC - 20 MHz DC - 20 MHz Resets (and Delays) POR, BOR (PWRT, OST) POR, BOR (PWRT, OST) Program Memory (14-bit words) 2K 2K Data Memory (bytes) 128 128 Interrupts 6 7 I/O Ports Ports A,B,C Ports A,B,C Timers 3 3 Capture/Compare/PWM modules 1 1 Serial Communications SSP 8-bit Analog-to-Digital Module DS35008A-page 2 SSP — Preliminary 5 input channels 1998 Microchip Technology Inc. PIC16C62B/72A Table of Contents 1.0 Device Overview.................................................................................................................................................... 5 2.0 Memory Organization ............................................................................................................................................ 7 3.0 I/O Ports .............................................................................................................................................................. 19 4.0 Timer0 Module..................................................................................................................................................... 25 5.0 Timer1 Module..................................................................................................................................................... 27 6.0 Timer2 Module..................................................................................................................................................... 31 7.0 Capture/Compare/PWM (CCP) Module(s) .......................................................................................................... 33 8.0 Synchronous Serial Port (SSP) Module .............................................................................................................. 39 9.0 Analog-to-Digital Converter (A/D) Module ........................................................................................................... 49 10.0 Special Features of the CPU ............................................................................................................................... 55 11.0 Instruction Set Summary ..................................................................................................................................... 69 12.0 Development Support.......................................................................................................................................... 71 13.0 Electrical Characteristics ..................................................................................................................................... 75 14.0 DC and AC Characteristics Graphs and Tables .................................................................................................. 95 15.0 Packaging Information......................................................................................................................................... 97 Appendix A: Revision History..................................................................................................................................... 103 Appendix B: Conversion Considerations ................................................................................................................... 103 Appendix C: Migration from Base-line to Mid-Range Devices ................................................................................... 104 Index ........................................................................................................................................................................... 105 On-Line Support.......................................................................................................................................................... 109 Reader Response ....................................................................................................................................................... 110 PIC16C62B/72A Product Identification System .......................................................................................................... 111 To Our Valued Customers Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please check our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number. e.g., DS30000A is version A of document DS30000. Errata An errata sheet may exist for current devices, describing minor operational differences (from the data sheet) and recommended workarounds. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) • The Microchip Corporate Literature Center; U.S. FAX: (602) 786-7277 When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include literature number) you are using. Corrections to this Data Sheet We constantly strive to improve the quality of all our products and documentation. We have spent a great deal of time to ensure that this document is correct. However, we realize that we may have missed a few things. If you find any information that is missing or appears in error, please: • Fill out and mail in the reader response form in the back of this data sheet. • E-mail us at [email protected]. We appreciate your assistance in making this a better document. 1998 Microchip Technology Inc. Preliminary DS35008A-page 3 PIC16C62B/72A NOTES: DS35008A-page 4 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 1.0 DEVICE OVERVIEW ommended reading for a better understanding of the device architecture and operation of the peripheral modules. This document contains device-specific information. Additional information may be found in the PICmicro™ Mid-Range Reference Manual, (DS33023), which may be obtained from your local Microchip Sales Representative or downloaded from the Microchip website. The Reference Manual should be considered a complementary document to this data sheet, and is highly rec- FIGURE 1-1: There are two devices (PIC16C62B, PIC16C72A) covered by this datasheet. The PIC16C62B does not have the A/D module implemented. Figure 1-1 is the block diagram for both devices. The pinouts are listed in Table 1-1. PIC16C62B/PIC16C72A BLOCK DIAGRAM 13 8 Data Bus Program Counter PORTA RA0/AN0(2) RA1/AN1(2) RA2/AN2(2) RA3/AN3/VREF(2) RA4/T0CKI RA5/SS/AN4(2) EPROM 2K x 14 Program Memory Program Bus RAM 128 x 8 File Registers 8 Level Stack (13-bit) 14 RAM Addr(1) PORTB 9 Addr MUX Instruction reg Direct Addr 7 8 RB0/INT Indirect Addr RB7:RB1 FSR reg STATUS reg 8 3 MUX Power-up Timer Instruction Decode & Control Timing Generation OSC1/CLKIN OSC2/CLKOUT Oscillator Start-up Timer ALU Power-on Reset RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6 RC7 8 Watchdog Timer Brown-out Reset MCLR PORTC W reg VDD, VSS Timer0 Timer1 Timer2 CCP1 Synchronous Serial Port A/D(2) Note 1: Higher order bits are from the STATUS register. 2: The A/D module is not available on the PIC16C62B. 1998 Microchip Technology Inc. Preliminary DS35008A-page 5 PIC16C62B/72A TABLE 1-1 PIC16C62B/PIC16C72A PINOUT DESCRIPTION DIP Pin# SOIC Pin# I/O/P Type OSC1/CLKIN 9 9 I OSC2/CLKOUT 10 10 O MCLR/VPP 1 1 I/P RA0/AN0(4) 2 2 I/O RA1/AN1(4) 3 3 I/O TTL RA1 can also be analog input1 RA2/AN2(4) 4 4 I/O TTL RA2 can also be analog input2 RA3/AN3/VREF(4) 5 5 I/O TTL RA3 can also be analog input3 or analog reference voltage RA4/T0CKI 6 6 I/O ST RA4 can also be the clock input to the Timer0 module. Output is open drain type. RA5/SS/AN4(4) 7 7 I/O TTL RB0/INT RB1 RB2 RB3 RB4 RB5 RB6 RB7 21 22 23 24 25 26 27 28 21 22 23 24 25 26 27 28 I/O I/O I/O I/O I/O I/O I/O I/O TTL/ST(1) TTL TTL TTL TTL TTL TTL/ST(2) TTL/ST(2) RA5 can also be analog input4 or the slave select for the synchronous serial port. PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-up on all inputs. RB0 can also be the external interrupt pin. RC0/T1OSO/T1CKI 11 11 I/O ST RC1/T1OSI RC2/CCP1 12 13 12 13 I/O I/O ST ST RC3/SCK/SCL 14 14 I/O ST RC4/SDI/SDA 15 15 I/O ST Pin Name RC5/SDO RC6 RC7 VSS VDD Legend: I = input Note 1: 2: 3: 4: Buffer Type Description ST/CMOS(3) Oscillator crystal input/external clock source input. — Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, the OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. ST Master clear (reset) input or programming voltage input. This pin is an active low reset to the device. PORTA is a bi-directional I/O port. TTL RA0 can also be analog input0 Interrupt on change pin. Interrupt on change pin. Interrupt on change pin. Serial programming clock. Interrupt on change pin. Serial programming data. PORTC is a bi-directional I/O port. RC0 can also be the Timer1 oscillator output or Timer1 clock input. RC1 can also be the Timer1 oscillator input. RC2 can also be the Capture1 input/Compare1 output/PWM1 output. RC3 can also be the synchronous serial clock input/output for both SPI and I2C modes. RC4 can also be the SPI Data In (SPI mode) or data I/O (I2C mode). RC5 can also be the SPI Data Out (SPI mode). 16 16 I/O ST 17 17 I/O ST 18 18 I/O ST 8, 19 8, 19 P — Ground reference for logic and I/O pins. 20 20 P — Positive supply for logic and I/O pins. O = output I/O = input/output P = power — = Not used TTL = TTL input ST = Schmitt Trigger input This buffer is a Schmitt Trigger input when configured as the external interrupt. This buffer is a Schmitt Trigger input when used in serial programming mode. This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. The A/D module is not available on the PIC16C62B. DS35008A-page 6 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 2.0 MEMORY ORGANIZATION FIGURE 2-1: There are two memory blocks in each of these PICmicros. Each block (Program Memory and Data Memory) has its own bus so that concurrent access can occur. PC<12:0> CALL, RETURN RETFIE, RETLW Additional information on device memory may be found in the PICmicro Mid-Range Reference Manual, (DS33023). 2.1 PROGRAM MEMORY MAP AND STACK 13 Stack Level 1 Program Memory Organization Stack Level 8 The reset vector is at 0000h and the interrupt vector is at 0004h. User Memory Space The PIC16C62B/72A PICmicros have a 13-bit program counter capable of addressing an 8K x 14 program memory space. Each device has 2K x 14 words of program memory. Accessing a location above the physically implemented address will cause a wraparound. Reset Vector 0000h Interrupt Vector 0004h 0005h On-chip Program Memory 07FFh 0800h 1FFFh 1998 Microchip Technology Inc. Preliminary DS35008A-page 7 PIC16C62B/72A 2.2 Data Memory Organization FIGURE 2-2: The data memory is partitioned into multiple banks which contain the General Purpose Registers and the Special Function Registers. Bits RP1 and RP0 are the bank select bits. RP1(1) RP0 = 00 → = 01 → = 10 → = 11 → Bank0 Bank1 Bank2 (not implemented) Bank3 (not implemented) REGISTER FILE MAP File Address (STATUS<6:5>) File Address 00h INDF(1) INDF(1) 01h TMR0 OPTION_REG 81h 02h PCL PCL 82h 03h STATUS STATUS 83h 84h 80h 04h FSR FSR 05h PORTA TRISA 85h 06h PORTB TRISB 86h Note 1: Maintain this bit clear to ensure upward compatibility with future products. 07h PORTC TRISC 87h Each bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the Special Function Registers. Above the Special Function Registers are General Purpose Registers, implemented as static RAM. All implemented banks contain special function registers. Some “high use” special function registers from one bank may be mirrored in another bank for code reduction and quicker access. 09h 2.2.1 08h 88h 89h 0Ah PCLATH PCLATH 8Ah 0Bh INTCON INTCON 8Bh 0Ch PIR1 PIE1 8Ch 0Eh TMR1L PCON 8Eh 0Fh TRM1H 8Fh 10h T1CON 90h 11h TRM2 12h T2CON PR2 92h 13h SSPBUF SSPADD 93h 14h SSPCON SSPSTAT 94h 15h CCPR1L 95h 16h CCPR1H 96h 17h CCP1CON 97h 8Dh 0Dh GENERAL PURPOSE REGISTER FILE The register file can be accessed either directly, or indirectly through the File Select Register FSR (Section 2.5). 91h 18h 98h 19h 99h 1Ah 9Ah 1Bh 9Bh 1Ch 9Ch 1Dh 9Dh 1Eh ADRES(2) 1Fh ADCON0(2) 20h General Purpose Registers 9Eh ADCON1(2) 9Fh General Purpose Registers A0h BFh C0h 7Fh FFh Bank 0 Bank 1 Unimplemented data memory locations, read as '0'. Note 1: Not a physical register. 2: These registers are not implemented on the PIC16C62B, read as '0'. DS35008A-page 8 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 2.2.2 SPECIAL FUNCTION REGISTERS The Special Function Registers are registers used by the CPU and Peripheral Modules for controlling the desired operation of the device. These registers are implemented as static RAM. A list of these registers is give in Table 2-1. TABLE 2-1 Addr The special function registers can be classified into two sets; core (CPU) and peripheral. Those registers associated with the core functions are described in detail in this section. Those related to the operation of the peripheral features are described in detail in that peripheral feature section. SPECIAL FUNCTION REGISTER SUMMARY Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets (4) Bank 0 00h INDF(1) Addressing this location uses contents of FSR to address data memory (not a physical register) 0000 0000 0000 0000 01h TMR0 Timer0 module’s register xxxx xxxx uuuu uuuu (1) 02h PCL 03h STATUS(1) 04h FSR(1) 05h PORTA(6) 06h PORTB(7) PORTB Data Latch when written: PORTB pins when read xxxx xxxx uuuu uuuu 07h PORTC(7) PORTC Data Latch when written: PORTC pins when read xxxx xxxx uuuu uuuu 08h-09h Program Counter's (PC) Least Significant Byte — IRP(5) RP1(5) RP0 TO 0000 0000 0000 0000 PD Z DC C Indirect data memory address pointer xxxx xxxx uuuu uuuu — --0x 0000 --0u 0000 — PORTA Data Latch when written: PORTA pins when read Unimplemented 0Ah PCLATH(1,2) 0Bh INTCON(1) 0Ch PIR1 rr01 1xxx rr0q quuu — — Write Buffer for the upper 5 bits of the Program Counter — — — GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u — ADIF(3) — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 0Dh — 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register 10h T1CON 11h TMR2 12h T2CON 13h SSPBUF 14h SSPCON 15h CCPR1L Capture/Compare/PWM Register1 (LSB) xxxx xxxx uuuu uuuu 16h CCPR1H Capture/Compare/PWM Register1 (MSB) xxxx xxxx uuuu uuuu 17h CCP1CON 18h-1Dh Unimplemented ---0 0000 ---0 0000 — — — xxxx xxxx uuuu uuuu T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 SSPM2 SSPM1 Timer2 module’s register — — SSPOV — — SSPEN CCP1X CKP CCP1Y SSPM3 CCP1M3 xxxx xxxx uuuu uuuu CCP1M2 CCP1M1 SSPM0 CCP1M0 Unimplemented (3) 1Eh ADRES 1Fh ADCON0(3) ADCS0 0000 0000 0000 0000 --00 0000 --00 0000 — A/D Result Register ADCS1 --00 0000 --uu uuuu 0000 0000 0000 0000 Synchronous Serial Port Receive Buffer/Transmit Register WCOL — xxxx xxxx uuuu uuuu — xxxx xxxx uuuu uuuu CHS2 CHS1 CHS0 GO/DONE — ADON 0000 00-0 0000 00-0 Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as '0', Shaded locations are unimplemented, read as '0'. Note 1: These registers can be addressed from either bank. 2: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8> whose contents are transferred to the upper byte of the program counter. 3: A/D not implemented on the PIC16C62B, maintain as ’0’. 4: Other (non power-up) resets include: external reset through MCLR and the Watchdog Timer Reset. 5: The IRP and RP1 bits are reserved. Always maintain these bits clear. 6: On any device reset, these pins are configured as inputs. 7: This is the value that will be in the port output latch. 1998 Microchip Technology Inc. Preliminary DS35008A-page 9 PIC16C62B/72A TABLE 2-1 Addr SPECIAL FUNCTION REGISTER SUMMARY (Cont.’d) Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets (4) Bank 1 80h INDF(1) 81h OPTION_ REG 82h PCL(1) Addressing this location uses contents of FSR to address data memory (not a physical register) 83h STATUS 84h FSR(1) 85h TRISA TRISB 87h TRISC 88h-89h 8Bh INTCON(1) 8Ch PIE1 8Eh PCON T0SE PSA PS2 PS1 PS0 IRP RP1 (5) RP0 TO — PD Z DC C rr01 1xxx rr0q quuu xxxx xxxx uuuu uuuu PORTA Data Direction Register --11 1111 --11 1111 PORTB Data Direction Register 1111 1111 1111 1111 PORTC Data Direction Register 1111 1111 1111 1111 — Write Buffer for the upper 5 bits of the Program Counter — — — — GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u — ADIE(3) — — SSPIE CCP1IE TMR2IE TMR1IE -0-- 0000 -0-- 0000 ---0 0000 ---0 0000 Unimplemented — — 1111 1111 1111 1111 0000 0000 0000 0000 Unimplemented 8Ah 8Fh-91h (5) — PCLATH(1,2) — T0CS Indirect data memory address pointer — 8Dh INTEDG Program Counter's (PC) Least Significant Byte (1) 86h RBPU 0000 0000 0000 0000 — — — — — — POR BOR Unimplemented — ---- --qq ---- --uu — — 92h PR2 Timer2 Period Register 1111 1111 1111 1111 93h SSPADD Synchronous Serial Port (I2C mode) Address Register 0000 0000 0000 0000 94h SSPSTAT 95h-9Eh 9Fh — ADCON1 SMP CKE D/A P S R/W UA BF Unimplemented (3) — — — — — PCFG2 PCFG1 PCFG0 0000 0000 0000 0000 — — ---- -000 ---- -000 Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as '0', Shaded locations are unimplemented, read as '0'. Note 1: These registers can be addressed from either bank. 2: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8> whose contents are transferred to the upper byte of the program counter. 3: A/D not implemented on the PIC16C62B, maintain as ’0’. 4: Other (non power-up) resets include: external reset through MCLR and the Watchdog Timer Reset. 5: The IRP and RP1 bits are reserved. Always maintain these bits clear. 6: On any device reset, these pins are configured as inputs. 7: This is the value that will be in the port output latch. DS35008A-page 10 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 2.2.2.1 It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the STATUS register because these instructions do not affect the Z, C or DC bits from the STATUS register. For other instructions, not affecting any status bits, see the "Instruction Set Summary." STATUS REGISTER The STATUS register, shown in Figure 2-3, contains the arithmetic status of the ALU, the RESET status and the bank select bits for data memory. The STATUS register can be the destination for any instruction, as with any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. Note 1: These devices do not use bits IRP and RP1 (STATUS<7:6>). Maintain these bits clear to ensure upward compatibility with future products. Note 2: The C and DC bits operate as a borrow and digit borrow bit, respectively, in subtraction. See the SUBLW and SUBWF instructions for examples. For example, CLRF STATUS will clear the upper-three bits and set the Z bit. This leaves the STATUS register as 000u u1uu (where u = unchanged). FIGURE 2-3: R/W-0 IRP bit7 bit 7: STATUS REGISTER (ADDRESS 03h, 83h) R/W-0 RP1 R/W-0 RP0 R-1 TO R-1 PD R/W-x Z R/W-x DC R/W-x C bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset IRP: Register Bank Select bit (used for indirect addressing) 1 = Bank 2, 3 (100h - 1FFh) - not implemented, maintain clear 0 = Bank 0, 1 (00h - FFh) - not implemented, maintain clear bit 6-5: RP1:RP0: Register Bank Select bits (used for direct addressing) 01 = Bank 1 (80h - FFh) 00 = Bank 0 (00h - 7Fh) Each bank is 128 bytes Note: RP1 = not implemented, maintain clear bit 4: TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3: PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit 2: Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1: DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result bit 0: C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) 1 = A carry-out from the most significant bit of the result occurred 0 = No carry-out from the most significant bit of the result occurred Note: For borrow the polarity is reversed. A subtraction is executed by adding the two’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register. 1998 Microchip Technology Inc. Preliminary DS35008A-page 11 PIC16C62B/72A 2.2.2.2 OPTION_REG REGISTER The OPTION_REG register is a readable and writable register which contains various control bits to configure the TMR0 prescaler/WDT postscaler (single assignable register known also as the prescaler), the External INT Interrupt, TMR0, and the weak pull-ups on PORTB. FIGURE 2-4: R/W-1 RBPU bit7 Note: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. OPTION_REG REGISTER (ADDRESS 81h) R/W-1 INTEDG R/W-1 T0CS R/W-1 T0SE R/W-1 PSA R/W-1 PS2 R/W-1 PS1 bit 7: RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values bit 6: INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin bit 5: T0CS: TMR0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4: T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin bit 3: PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module R/W-1 PS0 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 2-0: PS2:PS0: Prescaler Rate Select bits Bit Value TMR0 Rate WDT Rate 000 001 010 011 100 101 110 111 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 DS35008A-page 12 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 2.2.2.3 INTCON REGISTER The INTCON Register is a readable and writable register which contains various enable and flag bits for the TMR0 register overflow, RB Port change and External RB0/INT pin interrupts. FIGURE 2-5: R/W-0 GIE bit7 Note: Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. INTCON REGISTER (ADDRESS 0Bh, 8Bh) R/W-0 PEIE R/W-0 T0IE R/W-0 INTE R/W-0 RBIE R/W-0 T0IF R/W-0 INTF R/W-x RBIF bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7: GIE: Global Interrupt Enable bit 1 = Enables all un-masked interrupts 0 = Disables all interrupts bit 6: PEIE: Peripheral Interrupt Enable bit 1 = Enables all un-masked peripheral interrupts 0 = Disables all peripheral interrupts bit 5: T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 interrupt 0 = Disables the TMR0 interrupt bit 4: IINTE: RB0/INT External Interrupt Enable bit 1 = Enables the RB0/INT external interrupt 0 = Disables the RB0/INT external interrupt bit 3: RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2: T0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow bit 1: INTF: RB0/INT External Interrupt Flag bit 1 = The RB0/INT external interrupt occurred (must be cleared in software) 0 = The RB0/INT external interrupt did not occur bit 0: RBIF: RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state 1998 Microchip Technology Inc. Preliminary DS35008A-page 13 PIC16C62B/72A 2.2.2.4 PIE1 REGISTER This register contains the individual enable bits for the peripheral interrupts. FIGURE 2-6: U-0 — Note: Bit PEIE (INTCON<6>) must be set to enable any peripheral interrupt. PIE1 REGISTER (ADDRESS 8Ch) R/W-0 ADIE(1) U-0 U-0 — — R/W-0 SSPIE R/W-0 CCP1IE R/W-0 TMR2IE bit7 bit 7: Unimplemented: Read as ‘0’ bit 6: ADIE(1): A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt R/W-0 TMR1IE bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 5-4: Unimplemented: Read as ‘0’ bit 3: SSPIE: Synchronous Serial Port Interrupt Enable bit 1 = Enables the SSP interrupt 0 = Disables the SSP interrupt bit 2: CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt bit 1: TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt bit 0: TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt Note 1: The PIC16C62B does not have an A/D module. This bit location is reserved on these devices. Always maintain this bit clear. DS35008A-page 14 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 2.2.2.5 PIR1 REGISTER Note: This register contains the individual flag bits for the Peripheral interrupts. FIGURE 2-7: U-0 — Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. PIR1 REGISTER (ADDRESS 0Ch) R/W-0 ADIF(1) U-0 U-0 — — R/W-0 SSPIF R/W-0 CCP1IF R/W-0 TMR2IF bit7 R/W-0 TMR1IF bit0 bit 7: Unimplemented: Read as ‘0’ bit 6: ADIF(1): A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 5-4: Unimplemented: Read as ‘0’ bit 3: SSPIF: Synchronous Serial Port Interrupt Flag bit 1 = The transmission/reception is complete (must be cleared in software) 0 = Waiting to transmit/receive bit 2: CCP1IF: CCP1 Interrupt Flag bit Capture Mode 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare Mode 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM Mode Unused in this mode bit 1: TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred bit 0: TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow Note 1: The PIC16C62B does not have an A/D module. This bit location is reserved on these devices. Always maintain this bit clear. 1998 Microchip Technology Inc. Preliminary DS35008A-page 15 PIC16C62B/72A 2.2.2.6 PCON REGISTER Note: The Power Control (PCON) register contains a flag bit to allow differentiation between a Power-on Reset (POR) to an external MCLR Reset or WDT Reset. Those devices with brown-out detection circuitry contain an additional bit to differentiate a Brown-out Reset condition from a Power-on Reset condition. FIGURE 2-8: U-0 — bit7 If the BODEN configuration bit is set, BOR is ’1’ on Power-on Reset. If the BODEN configuration bit is clear, BOR is unknown on Power-on Reset. The BOR status bit is a "don't care" and is not necessarily predictable if the brown-out circuit is disabled (the BODEN configuration bit is clear). BOR must then be set by the user and checked on subsequent resets to see if it is clear, indicating a brown-out has occurred. PCON REGISTER (ADDRESS 8Eh) U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0 POR R/W-q BOR bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7-2: Unimplemented: Read as '0' bit 1: POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0: BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) DS35008A-page 16 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 2.3 PCL and PCLATH 2.4 The program counter (PC) specifies the address of the instruction to fetch for execution. The PC is 13 bits wide. The low byte is called the PCL register. This register is readable and writable. The high byte is called the PCH register. This register contains the PC<12:8> bits and is not directly readable or writable. All updates to the PCH register go through the PCLATH register. 2.3.1 STACK The stack allows a combination of up to 8 program calls and interrupts to occur. The stack contains the return address from this branch in program execution. Program Memory Paging The CALL and GOTO instructions provide 11 bits of address to allow branching within any 2K program memory page. When doing a CALL or GOTO instruction the upper bit of the address is provided by PCLATH<3>. When doing a CALL or GOTO instruction, the user must ensure that the page select bit is programmed so that the desired program memory page is addressed. If a return from a CALL instruction (or interrupt) is executed, the entire 13-bit PC is pushed onto the stack. Therefore, manipulation of the PCLATH<3> bit is not required for the return instructions (which POPs the address from the stack). Midrange devices have an 8 level deep x 13-bit wide hardware stack. The stack space is not part of either program or data space and the stack pointer is not readable or writable. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN, RETLW or a RETFIE instruction execution. PCLATH is not modified when the stack is PUSHed or POPed. After the stack has been PUSHed eight times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on). 1998 Microchip Technology Inc. Preliminary DS35008A-page 17 PIC16C62B/72A 2.5 Indirect Addressing, INDF and FSR Registers A simple program to clear RAM locations 20h-2Fh using indirect addressing is shown in Example 2-2. The INDF register is not a physical register. Addressing INDF actually addresses the register whose address is contained in the FSR register (FSR is a pointer). This is indirect addressing. EXAMPLE 2-1: EXAMPLE 2-2: INDIRECT ADDRESSING movlw movwf clrf incf btfss goto NEXT • • • • Register file 05 contains the value 10h Register file 06 contains the value 0Ah Load the value 05 into the FSR register A read of the INDF register will return the value of 10h • Increment the value of the FSR register by one (FSR = 06) • A read of the INDR register now will return the value of 0Ah. HOW TO CLEAR RAM USING INDIRECT ADDRESSING 0x20 FSR INDF FSR FSR,4 NEXT ;initialize pointer ; to RAM ;clear INDF register ;inc pointer ;all done? ;NO, clear next CONTINUE : ;YES, continue An effective 9-bit address is obtained by concatenating the 8-bit FSR register and the IRP bit (STATUS<7>), as shown in Figure 2-9. However, IRP is not used in the PIC16C62B/72A. Reading INDF itself indirectly (FSR = 0) will produce 00h. Writing to the INDF register indirectly results in a no-operation (although STATUS bits may be affected). FIGURE 2-9: DIRECT/INDIRECT ADDRESSING Direct Addressing RP1:RP0 6 Indirect Addressing from opcode 0 IRP 7 FSR register 0 (2) (2) bank select bank select location select 00 00h 01 80h 10 100h location select 11 180h not used (3) (3) Data Memory(1) 7Fh Bank 0 FFh 17Fh Bank 1 1FFh Bank 2 Bank 3 Note 1: For register file map detail see Figure 2-2. 2: Maintain clear for upward compatibility with future products. 3: Not implemented. DS35008A-page 18 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 3.0 I/O PORTS FIGURE 3-1: Some pins for these I/O ports are multiplexed with an alternate function for the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Additional information on I/O ports may be found in the PICmicro™ Mid-Range Reference Manual, (DS33023). Data bus BLOCK DIAGRAM OF RA3:RA0 AND RA5 PINS D Q VDD WR Port Q CK P Data Latch 3.1 PORTA and the TRISA Register D PORTA is a 6-bit wide bi-directional port. The corresponding data direction register is TRISA. Setting a TRISA bit (=1) will make the corresponding PORTA pin an input, i.e., put the corresponding output driver in a hi-impedance mode. Clearing a TRISA bit (=0) will make the corresponding PORTA pin an output, i.e., put the contents of the output latch on the selected pin. WR TRIS On the PIC16C72A device, other PORTA pins are multiplexed with analog inputs and analog VREF input. The operation of each pin is selected by clearing/setting the control bits in the ADCON1 register (A/D Control Register1). Note: Q BSF MOVLW STATUS, RP0 0xCF MOVWF TRISA ; ; ; ; ; ; ; ; ; ; ; ; D EN RD PORT To A/D Converter (72A only) Note 1: I/O pins have protection diodes to VDD and VSS. FIGURE 3-2: Data bus WR PORT BLOCK DIAGRAM OF RA4/T0CKI PIN D Q CK Q N I/O pin(1) Data Latch WR TRIS INITIALIZING PORTA STATUS, RP0 PORTA TTL input buffer RD TRIS The TRISA register controls the direction of the RA pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA register are maintained set when using them as analog inputs. BCF CLRF Analog input mode (72B only) TRIS Latch On a Power-on Reset, these pins are configured as analog inputs and read as '0'. EXAMPLE 3-1: I/O pin(1) VSS Q CK Reading the PORTA register reads the status of the pins whereas writing to it will write to the port latch. All write operations are read-modify-write operations. Therefore a write to a port implies that the port pins are read, this value is modified, and then written to the port data latch. Pin RA4 is multiplexed with the Timer0 module clock input to become the RA4/T0CKI pin. The RA4/T0CKI pin is a Schmitt Trigger input and an open drain output. All other RA port pins have TTL input levels and full CMOS output drivers. N Q D Q CK Q VSS Schmitt Trigger input buffer TRIS Latch Initialize PORTA by clearing output data latches Select Bank 1 Value used to initialize data direction Set RA<3:0> as inputs RA<5:4> as outputs TRISA<7:6> are always read as '0'. RD TRIS Q D EN EN RD PORT TMR0 clock input Note 1: Note 1: I/O pin has protection diodes to VSS only. 1998 Microchip Technology Inc. Preliminary DS35008A-page 19 PIC16C62B/72A TABLE 3-1 PORTA FUNCTIONS Name Bit# Buffer Function RA0/AN0 bit0 TTL Input/output or analog input(1) RA1/AN1 bit1 TTL Input/output or analog input(1) RA2/AN2 bit2 TTL Input/output or analog input(1) RA3/AN3/VREF bit3 TTL RA4/T0CKI bit4 ST Input/output or analog input(1) or VREF(1) Input/output or external clock input for Timer0 Output is open drain type bit5 TTL Input/output or slave select input for synchronous serial port or analog input(1) RA5/SS/AN4 Legend: TTL = TTL input, ST = Schmitt Trigger input Note 1: On PIC16C72A only. TABLE 3-2 SUMMARY OF REGISTERS ASSOCIATED WITH PORTA Address Name 05h Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other resets — — RA5 RA4 RA3 RA2 RA1 RA0 --0x 0000 --0u 0000 — — RA5 RA4 RA3 RA2 RA1 RA0 --xx xxxx --uu uuuu --11 1111 --11 1111 ---- -000 ---- -000 PORTA (for PIC16C72A only) 05h PORTA (for PIC16C62B only) 85h TRISA — — 9Fh ADCON1(1) — — PORTA Data Direction Register — — — PCFG2 PCFG1 PCFG0 Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by PORTA. Note 1: On PIC16C72A only. DS35008A-page 20 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 3.2 PORTB and the TRISB Register PORTB is an 8-bit wide bi-directional port. The corresponding data direction register is TRISB. Setting a TRISB bit (=1) will make the corresponding PORTB pin an input, i.e., put the corresponding output driver in a hi-impedance mode. Clearing a TRISB bit (=0) will make the corresponding PORTB pin an output, i.e., put the contents of the output latch on the selected pin. EXAMPLE 3-1: BCF CLRF BSF MOVLW MOVWF INITIALIZING PORTB STATUS, RP0 PORTB STATUS, RP0 0xCF TRISB ; ; ; ; ; ; ; ; ; ; ; Initialize PORTB by clearing output data latches Select Bank 1 Value used to initialize data direction Set RB<3:0> as inputs RB<5:4> as outputs RB<7:6> as inputs Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION_REG<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. FIGURE 3-3: WR Port Any read or write of PORTB. This will end the mismatch condition. Clear flag bit RBIF. b) A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition, and allow flag bit RBIF to be cleared. The interrupt on change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt on change feature. Polling of PORTB is not recommended while using the interrupt on change feature. FIGURE 3-4: Data bus weak P pull-up WR Port Data Latch D Q CK BLOCK DIAGRAM OF RB7:RB4 PINS weak P pull-up Data Latch D Q I/O pin(1) CK TRIS Latch D Q I/O pin(1) WR TRIS TRIS Latch D Q WR TRIS a) RBPU(2) VDD Data bus This interrupt can wake the device from SLEEP. The user, in the interrupt service routine, can clear the interrupt in the following manner: VDD BLOCK DIAGRAM OF RB3:RB0 PINS RBPU(2) Four of PORTB’s pins, RB7:RB4, have an interrupt on change feature. Only pins configured as inputs can cause this interrupt to occur (i.e. any RB7:RB4 pin configured as an output is excluded from the interrupt on change comparison). The input pins (of RB7:RB4) are compared with the old value latched on the last read of PORTB. The “mismatch” outputs of RB7:RB4 are OR’ed together to generate the RB Port Change Interrupt with flag bit RBIF (INTCON<0>). TTL Input Buffer CK TTL Input Buffer CK RD TRIS Q RD TRIS RD Port Latch D EN RD Port Q EN Q D RD Port EN RB0/INT RD Port Note 1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). 1998 Microchip Technology Inc. Q1 Set RBIF D From other RB7:RB4 pins Schmitt Trigger Buffer ST Buffer Q3 RB7:RB6 in serial programming mode Note 1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). Preliminary DS35008A-page 21 PIC16C62B/72A TABLE 3-3 Name PORTB FUNCTIONS Bit# Buffer Function TTL/ST(1) Input/output pin or external interrupt input. Internal software programmable weak pull-up. RB1 bit1 TTL Input/output pin. Internal software programmable weak pull-up. RB2 bit2 TTL Input/output pin. Internal software programmable weak pull-up. RB3 bit3 TTL Input/output pin. Internal software programmable weak pull-up. RB4 bit4 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. RB5 bit5 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. RB6 bit6 TTL/ST(2) Input/output pin (with interrupt on change). Internal software programmable weak pull-up. Serial programming clock. RB7 bit7 TTL/ST(2) Input/output pin (with interrupt on change). Internal software programmable weak pull-up. Serial programming data. Legend: TTL = TTL input, ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in serial programming mode. RB0/INT TABLE 3-4 bit0 SUMMARY OF REGISTERS ASSOCIATED WITH PORTB Address Name 06h PORTB 86h TRISB 81h OPTION_ REG Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx xxxx uuuu uuuu 1111 1111 1111 1111 1111 1111 1111 1111 PORTB Data Direction Register RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB. DS35008A-page 22 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 3.3 PORTC and the TRISC Register FIGURE 3-5: PORTC is an 8-bit wide bi-directional port. The corresponding data direction register is TRISC. Setting a TRISC bit (=1) will make the corresponding PORTC pin an input, i.e., put the corresponding output driver in a hi-impedance mode. Clearing a TRISC bit (=0) will make the corresponding PORTC pin an output, i.e., put the contents of the output latch on the selected pin. PORTC is multiplexed with several peripheral functions (Table 3-5). PORTC pins have Schmitt Trigger input buffers. When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTC pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. Since the TRIS bit override is in effect while the peripheral is enabled, read-modifywrite instructions (BSF, BCF, XORWF) with TRISC as destination should be avoided. The user should refer to the corresponding peripheral section for the correct TRIS bit settings. EXAMPLE 3-1: INITIALIZING PORTC BCF CLRF STATUS, RP0 PORTC BSF MOVLW STATUS, RP0 0xCF MOVWF TRISC ; ; ; ; ; ; ; ; ; ; ; Select Bank 0 Initialize PORTC by clearing output data latches Select Bank 1 Value used to initialize data direction Set RC<3:0> as inputs RC<5:4> as outputs RC<7:6> as inputs 1998 Microchip Technology Inc. PORTC BLOCK DIAGRAM (PERIPHERAL OUTPUT OVERRIDE) PORT/PERIPHERAL Select(2) Peripheral Data Out Data bus WR PORT D VDD 0 Q P 1 CK Q Data Latch WR TRIS D CK I/O pin(1) Q Q N TRIS Latch VSS Schmitt Trigger RD TRIS Peripheral OE(3) RD PORT Peripheral input Q D EN Note 1: I/O pins have diode protection to VDD and VSS. 2: Port/Peripheral select signal selects between port data and peripheral output. 3: Peripheral OE (output enable) is only activated if peripheral select is active. Preliminary DS35008A-page 23 PIC16C62B/72A TABLE 3-5 PORTC FUNCTIONS Name Bit# Buffer Type Function RC0/T1OSO/T1CKI bit0 ST Input/output port pin or Timer1 oscillator output/Timer1 clock input RC1/T1OSI bit1 ST Input/output port pin or Timer1 oscillator input RC2/CCP1 bit2 ST Input/output port pin or Capture1 input/Compare1 output/PWM1 output RC3/SCK/SCL bit3 ST RC3 can also be the synchronous serial clock for both SPI and I2C modes. RC4/SDI/SDA bit4 ST RC4 can also be the SPI Data In (SPI mode) or data I/O (I2C mode). RC5/SDO bit5 ST Input/output port pin or Synchronous Serial Port data output RC6 bit6 ST Input/output port pin RC7 bit7 ST Input/output port pin Legend: ST = Schmitt Trigger input TABLE 3-6 SUMMARY OF REGISTERS ASSOCIATED WITH PORTC Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets 07h PORTC RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 xxxx xxxx uuuu uuuu 87h TRISC 1111 1111 1111 1111 PORTC Data Direction Register Legend: x = unknown, u = unchanged. DS35008A-page 24 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 4.0 TIMER0 MODULE Additional information on external clock requirements is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). The Timer0 module timer/counter has the following features: • • • • • • 4.2 8-bit timer/counter Readable and writable Internal or external clock select Edge select for external clock 8-bit software programmable prescaler Interrupt on overflow from FFh to 00h An 8-bit counter is available as a prescaler for the Timer0 module, or as a postscaler for the Watchdog Timer, respectively (Figure 4-2). For simplicity, this counter is being referred to as “prescaler” throughout this data sheet. Note that there is only one prescaler available which is mutually exclusively shared between the Timer0 module and the Watchdog Timer. Thus, a prescaler assignment for the Timer0 module means that there is no prescaler for the Watchdog Timer, and vice-versa. Figure 4-1 is a simplified block diagram of the Timer0 module. Additional information on timer modules is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). 4.1 The prescaler is not readable or writable. The PSA and PS2:PS0 bits (OPTION_REG<3:0>) determine the prescaler assignment and prescale ratio. Timer0 Operation Timer0 can operate as a timer or as a counter. Clearing bit PSA will assign the prescaler to the Timer0 module. When the prescaler is assigned to the Timer0 module, prescale values of 1:2, 1:4, ..., 1:256 are selectable. Timer mode is selected by clearing bit T0CS (OPTION_REG<5>). In timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If the TMR0 register is written, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register. Setting bit PSA will assign the prescaler to the Watchdog Timer (WDT). When the prescaler is assigned to the WDT, prescale values of 1:1, 1:2, ..., 1:128 are selectable. Counter mode is selected by setting bit T0CS (OPTION_REG<5>). In counter mode, Timer0 will increment either on every rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit T0SE (OPTION_REG<4>). Clearing bit T0SE selects the rising edge. Restrictions on the external clock input are discussed below. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g. CLRF 1, MOVWF 1, BSF 1,x....etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the WDT. Note: When an external clock input is used for Timer0, it must meet certain requirements. The requirements ensure the external clock can be synchronized with the internal phase clock (TOSC). Also, there is a delay in the actual incrementing of Timer0 after synchronization. FIGURE 4-1: Prescaler Writing to TMR0 when the prescaler is assigned to Timer0 will clear the prescaler count, but will not change the prescaler assignment. TIMER0 BLOCK DIAGRAM Data bus FOSC/4 0 PSout 1 1 Programmable Prescaler RA4/T0CKI pin 0 8 Sync with Internal clocks TMR0 PSout (2 cycle delay) T0SE 3 PS2, PS1, PS0 PSA T0CS Set interrupt flag bit T0IF on overflow Note 1: T0CS, T0SE, PSA, PS2:PS0 (OPTION_REG<5:0>). 2: The prescaler is shared with Watchdog Timer (refer to Figure 4-2 for detailed block diagram). 1998 Microchip Technology Inc. Preliminary DS35008A-page 25 PIC16C62B/72A 4.2.1 4.3 SWITCHING PRESCALER ASSIGNMENT The prescaler assignment is fully under software control, i.e., it can be changed “on the fly” during program execution. Note: The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit T0IF (INTCON<2>). The interrupt can be masked by clearing bit T0IE (INTCON<5>). Bit T0IF must be cleared in software by the Timer0 module interrupt service routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor from SLEEP since the timer is shut off during SLEEP. To avoid an unintended device RESET, a specific instruction sequence (shown in the PICmicro Mid-Range Reference Manual, DS33023) must be executed when changing the prescaler assignment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled. FIGURE 4-2: Timer0 Interrupt BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER Data Bus CLKOUT (=Fosc/4) 0 RA4/T0CKI pin 8 M U X 1 M U X 0 1 SYNC 2 Cycles TMR0 reg T0SE T0CS 0 1 Watchdog Timer Set flag bit T0IF on Overflow PSA 8-bit Prescaler M U X 8 8 - to - 1MUX PS2:PS0 PSA 1 0 WDT Enable bit MUX PSA WDT Time-out Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION_REG<5:0>). TABLE 4-1 REGISTERS ASSOCIATED WITH TIMER0 Address Name 01h TMR0 0Bh,8Bh INTCON 81h OPTION_REG 85h TRISA Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Timer0 module’s register GIE PEIE RBPU INTEDG — — T0IE INTE RBIE T0IF INTF RBIF T0CS T0SE PSA PS2 PS1 PS0 PORTA Data Direction Register Value on: POR, BOR Value on all other resets xxxx xxxx uuuu uuuu 0000 000x 0000 000u 1111 1111 1111 1111 --11 1111 --11 1111 Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by Timer0. DS35008A-page 26 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 5.0 TIMER1 MODULE 5.1 The Timer1 module timer/counter has the following features: • 16-bit timer/counter (Two 8-bit registers; TMR1H and TMR1L) • Readable and writable (Both registers) • Internal or external clock select • Interrupt on overflow from FFFFh to 0000h • Reset from CCP module trigger Timer1 can operate in one of these modes: • As a timer • As a synchronous counter • As an asynchronous counter The operating mode is determined by the clock select bit, TMR1CS (T1CON<1>). Timer1 has a control register, shown in Figure 5-1. Timer1 can be enabled/disabled by setting/clearing control bit TMR1ON (T1CON<0>). Figure 5-2 is a simplified block diagram of the Timer1 module. Additional information on timer modules is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). FIGURE 5-1: Timer1 Operation In timer mode, Timer1 increments every instruction cycle. In counter mode, it increments on every rising edge of the external clock input. When the Timer1 oscillator is enabled (T1OSCEN is set), the RC1/T1OSI and RC0/T1OSO/T1CKI pins become inputs. That is, the TRISC<1:0> value is ignored. Timer1 also has an internal “reset input”. This reset can be generated by the CCP module (Section 7.0). T1CON: TIMER1 CONTROL REGISTER (ADDRESS 10h) U-0 U-0 — — R/W-0 R/W-0 R/W-0 R/W-0 T1CKPS1 T1CKPS0 T1OSCEN T1SYNC bit7 R/W-0 R/W-0 TMR1CS TMR1ON bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7-6: Unimplemented: Read as '0' bit 5-4: T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 3: T1OSCEN: Timer1 Oscillator Enable Control bit 1 = Oscillator is enabled 0 = Oscillator is shut off Note: The oscillator inverter and feedback resistor are turned off to eliminate power drain bit 2: T1SYNC: Timer1 External Clock Input Synchronization Control bit TMR1CS = 1 1 = Do not synchronize external clock input 0 = Synchronize external clock input TMR1CS = 0 This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0. bit 1: TMR1CS: Timer1 Clock Source Select bit 1 = External clock from pin RC0/T1OSO/T1CKI (on the rising edge) 0 = Internal clock (FOSC/4) bit 0: TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 1998 Microchip Technology Inc. Preliminary DS35008A-page 27 PIC16C62B/72A FIGURE 5-2: TIMER1 BLOCK DIAGRAM Set flag bit TMR1IF on Overflow 0 TMR1 TMR1H Synchronized clock input TMR1L 1 TMR1ON on/off T1SYNC T1OSC RC0/T1OSO/T1CKI RC1/T1OSI 1 T1OSCEN FOSC/4 Enable Internal Oscillator(1) Clock Prescaler 1, 2, 4, 8 Synchronize det 0 2 T1CKPS1:T1CKPS0 TMR1CS SLEEP input Note 1: When the T1OSCEN bit is cleared, the inverter and feedback resistor are turned off. This eliminates power drain. DS35008A-page 28 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 5.2 Timer1 Oscillator 5.3 A crystal oscillator circuit is built in between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting control bit T1OSCEN (T1CON<3>). The oscillator is a low power oscillator rated up to 200 kHz. It will continue to run during SLEEP. It is primarily intended for a 32 kHz crystal. Table 5-1 shows the capacitor selection for the Timer1 oscillator. The TMR1 Register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The TMR1 Interrupt, if enabled, is generated on overflow which is latched in interrupt flag bit TMR1IF (PIR1<0>). This interrupt can be enabled/disabled by setting/clearing TMR1 interrupt enable bit TMR1IE (PIE1<0>). 5.4 The Timer1 oscillator is identical to the LP oscillator. The user must provide a software time delay to ensure proper oscillator start-up. TABLE 5-1 Timer1 Interrupt Resetting Timer1 using a CCP Trigger Output If the CCP module is configured in compare mode to generate a “special event trigger" (CCP1M3:CCP1M0 = 1011), this signal will reset Timer1 and start an A/D conversion (if the A/D module is enabled). CAPACITOR SELECTION FOR THE TIMER1 OSCILLATOR Note: Osc Type Freq C1 C2 LP 32 kHz 100 kHz 200 kHz 33 pF 15 pF 15 pF 33 pF 15 pF 15 pF Timer1 must be configured for either timer or synchronized counter mode to take advantage of this feature. If Timer1 is running in asynchronous counter mode, this reset operation may not work. These values are for design guidance only. Crystals Tested: In the event that a write to Timer1 coincides with a special event trigger from CCP1, the write will take precedence. 32.768 kHz Epson C-001R32.768K-A ± 20 PPM 100 kHz Epson C-2 100.00 KC-P ± 20 PPM 200 kHz STD XTL 200.000 kHz ± 20 PPM Note 1: Higher capacitance increases the stability of oscillator but also increases the start-up time. 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. TABLE 5-2 The special event triggers from the CCP1 module will not set interrupt flag bit TMR1IF (PIR1<0>). In this mode of operation, the CCPR1H:CCPR1L registers pair effectively becomes the period register for Timer1. REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER Value on POR, BOR Value on all other resets Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0Ch PIR1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 TMR1IE -0-- 0000 -0-- 0000 — 8Ch PIE1 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 10h T1CON Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer1 module. — ADIE — 1998 Microchip Technology Inc. — — SSPIE CCP1IE TMR2IE 0000 000x 0000 000u T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu Preliminary DS35008A-page 29 PIC16C62B/72A NOTES: DS35008A-page 30 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 6.0 TIMER2 MODULE The Timer2 module timer has the following features: • • • • • • • 8-bit timer (TMR2 register) 8-bit period register (PR2) Readable and writable (Both registers) Software programmable prescaler (1:1, 1:4, 1:16) Software programmable postscaler (1:1 to 1:16) Interrupt on TMR2 match of PR2 SSP module optional use of TMR2 output to generate clock shift FIGURE 6-1: Timer2 has a control register, shown in Figure 6-1. Timer2 can be shut off by clearing control bit TMR2ON (T2CON<2>) to minimize power consumption. Figure 6-2 is a simplified block diagram of the Timer2 module. Additional information on timer modules is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). T2CON: TIMER2 CONTROL REGISTER (ADDRESS 12h) U-0 — bit7 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 bit0 bit 7: Unimplemented: Read as '0' bit 6-3: TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale • • • 1111 = 1:16 Postscale bit 2: TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off bit 1-0: T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 FIGURE 6-2: Sets flag bit TMR2IF R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset TIMER2 BLOCK DIAGRAM TMR2 output (1) Reset Postscaler 1:1 to 1:16 4 EQ TMR2 reg Comparator Prescaler 1:1, 1:4, 1:16 FOSC/4 2 PR2 reg Note 1: TMR2 register output can be software selected by the SSP Module as a baud clock. 1998 Microchip Technology Inc. Preliminary DS35008A-page 31 PIC16C62B/72A 6.1 Timer2 Operation 6.2 Timer2 can be used as the PWM time-base for PWM mode of the CCP module. The TMR2 register is readable and writable, and is cleared on any device reset. The input clock (FOSC/4) has a prescale option of 1:1, 1:4 or 1:16, selected by control bits T2CKPS1:T2CKPS0 (T2CON<1:0>). The match output of TMR2 goes through a 4-bit postscaler (which gives a 1:1 to 1:16 scaling inclusive) to generate a TMR2 interrupt (latched in flag bit TMR2IF, (PIR1<1>)). Timer2 Interrupt The Timer2 module has an 8-bit period register PR2. Timer2 increments from 00h until it matches PR2 and then resets to 00h on the next increment cycle. PR2 is a readable and writable register. The PR2 register is initialized to FFh upon reset. 6.3 Output of TMR2 The output of TMR2 (before the postscaler) is fed to the Synchronous Serial Port module which optionally uses it to generate shift clock. The prescaler and postscaler counters are cleared when any of the following occurs: • a write to the TMR2 register • a write to the T2CON register • any device reset (Power-on Reset, MCLR reset, Watchdog Timer reset, or Brown-out Reset) TMR2 is not cleared when T2CON is written. TABLE 6-1 REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER Value on POR, BOR Value on all other resets Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0Ch PIR1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -00- 0000 0000 0000 TMR1IE -0-- 0000 0000 0000 8Ch PIE1 11h TMR2 12h T2CON 92h PR2 Legend: — ADIE — — SSPIE CCP1IE TMR2IE 0000 0000 0000 0000 Timer2 module’s register — 0000 000x 0000 000u TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 1111 1111 1111 1111 Timer2 Period Register x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer2 module. DS35008A-page 32 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 7.0 CAPTURE/COMPARE/PWM (CCP) MODULE(S) Additional information on the CCP module is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). Each CCP (Capture/Compare/PWM) module contains a 16-bit register which can operate as a 16-bit capture register, as a 16-bit compare register or as a PWM master/slave Duty Cycle register. Table 7-1 shows the timer resources of the CCP module modes. TABLE 7-1 Capture/Compare/PWM Register 1 (CCPR1) is comprised of two 8-bit registers: CCPR1L (low byte) and CCPR1H (high byte). The CCP1CON register controls the operation of CCP1. All are readable and writable. FIGURE 7-1: U-0 — bit7 U-0 — CCP MODE - TIMER RESOURCE CCP Mode Timer Resource Capture Compare PWM Timer1 Timer1 Timer2 CCP1CON REGISTER (ADDRESS 17h) R/W-0 CCP1X R/W-0 R/W-0 CCP1Y CCP1M3 R/W-0 CCP1M2 R/W-0 R/W-0 CCP1M1 CCP1M0 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n =Value at POR reset bit 7-6: Unimplemented: Read as '0' bit 5-4: CCP1X:CCP1Y: PWM Least Significant bits Capture Mode: Unused Compare Mode: Unused PWM Mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L. bit 3-0: CCP1M3:CCP1M0: CCP1 Mode Select bits 0000 = Capture/Compare/PWM off (resets CCP1 module) 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, set output on match (CCP1IF bit is set) 1001 = Compare mode, clear output on match (CCP1IF bit is set) 1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is unaffected) 1011 = Compare mode, trigger special event (CCP1IF bit is set; CCP1 resets TMR1 and starts an A/D conversion (if A/D module is enabled)) 11xx = PWM mode 1998 Microchip Technology Inc. Preliminary DS35008A-page 33 PIC16C62B/72A 7.1 Capture Mode 7.1.4 In Capture mode, CCPR1H:CCPR1L captures the 16-bit value of the TMR1 register when an event occurs on pin RC2/CCP1. An event is defined as: • • • • every falling edge every rising edge every 4th rising edge every 16th rising edge An event is selected by control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). When a capture is made, the interrupt request flag bit CCP1IF (PIR1<2>) is set. It must be cleared in software. If another capture occurs before the value in register CCPR1 is read, the old captured value will be lost. FIGURE 7-2: CAPTURE MODE OPERATION BLOCK DIAGRAM Prescaler ÷ 1, 4, 16 Set flag bit CCP1IF (PIR1<2>) RC2/CCP1 Pin CCPR1H and edge detect CCP PRESCALER There are four prescaler settings, specified by bits CCP1M3:CCP1M0. Whenever the CCP module is turned off, or the CCP module is not in capture mode, the prescaler counter is cleared. This means that any reset will clear the prescaler counter. Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared, therefore the first capture may be from a non-zero prescaler. Example 7-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the “false” interrupt. EXAMPLE 7-1: CHANGING BETWEEN CAPTURE PRESCALERS CLRF MOVLW CCP1CON NEW_CAPT_PS MOVWF CCP1CON ;Turn CCP module off ;Load the W reg with ; the new prescaler ; mode value and CCP ON ;Load CCP1CON with this ; value CCPR1L Capture Enable TMR1H TMR1L CCP1CON<3:0> Q’s 7.1.1 CCP PIN CONFIGURATION In Capture mode, the RC2/CCP1 pin should be configured as an input by setting the TRISC<2> bit. Note: 7.1.2 If the RC2/CCP1 is configured as an output, a write to the port can cause a capture condition. TIMER1 MODE SELECTION Timer1 must be running in timer mode or synchronized counter mode for the CCP module to use the capture feature. In asynchronous counter mode, the capture operation may not work. 7.1.3 SOFTWARE INTERRUPT When the Capture mode is changed, a false capture interrupt may be generated. The user should keep bit CCP1IE (PIE1<2>) clear to avoid false interrupts and should clear the flag bit CCP1IF following any such change in operating mode. DS35008A-page 34 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 7.2 Compare Mode 7.2.1 In Compare mode, the 16-bit CCPR1 register value is constantly compared against the TMR1 register pair value. When a match occurs, the RC2/CCP1 pin is: • driven High • driven Low • remains Unchanged The user must configure the RC2/CCP1 pin as an output by clearing the TRISC<2> bit. Note: 7.2.2 The action on the pin is based on the value of control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). At the same time, interrupt flag bit CCP1IF is set. FIGURE 7-3: CCP PIN CONFIGURATION COMPARE MODE OPERATION BLOCK DIAGRAM TIMER1 MODE SELECTION Timer1 must be running in Timer mode or Synchronized Counter mode if the CCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work. 7.2.3 SOFTWARE INTERRUPT MODE When generate software interrupt is chosen the CCP1 pin is not affected. Only a CCP interrupt is generated (if enabled). Special event trigger will: reset Timer1, but not set interrupt flag bit TMR1IF (PIR1<0>), and set bit GO/DONE (ADCON0<2>) which starts an A/D conversion 7.2.4 SPECIAL EVENT TRIGGER In this mode, an internal hardware trigger is generated which may be used to initiate an action. Special Event Trigger Set flag bit CCP1IF (PIR1<2>) CCPR1H CCPR1L Q S Output Logic match RC2/CCP1 R Pin TRISC<2> Output Enable CCP1CON<3:0> Mode Select Clearing the CCP1CON register will force the RC2/CCP1 compare output latch to the default low level. This is not the data latch. Comparator TMR1H TMR1L The special event trigger output of CCP1 resets the TMR1 register pair. This allows the CCPR1 register to effectively be a 16-bit programmable period register for Timer1. The special trigger output of CCP2 resets the TMR1 register pair, and starts an A/D conversion (if the A/D module is enabled). Note: TABLE 7-2 Address The special event trigger from the CCP2 module will not set interrupt flag bit TMR1IF (PIR1<0>). REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, AND TIMER1 Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on all other resets 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF 0Ch PIR1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 8Ch PIE1 — ADIE — — SSPIE CCP1IE TMR2IE TMR1IE -0-- 0000 -0-- 0000 87h TRISC PORTC Data Direction Register 1111 1111 1111 1111 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1register xxxx xxxx uuuu uuuu 10h T1CON 15h CCPR1L Capture/Compare/PWM register1 (LSB) xxxx xxxx uuuu uuuu 16h CCPR1H Capture/Compare/PWM register1 (MSB) xxxx xxxx uuuu uuuu 17h Legend: CCP1CON — — — — RBIF Value on POR, BOR 0000 000x 0000 000u T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000 x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by Capture and Timer1. 1998 Microchip Technology Inc. Preliminary DS35008A-page 35 PIC16C62B/72A 7.3 PWM Mode 7.3.1 In Pulse Width Modulation (PWM) mode, the CCP1 pin produces up to a 10-bit resolution PWM output. Since the CCP1 pin is multiplexed with the PORTC data latch, the TRISC<2> bit must be cleared to make the CCP1 pin an output. Note: Clearing the CCP1CON register will force the CCP1 PWM output latch to the default low level. This is not the PORTC I/O data latch. Figure 7-4 shows a simplified block diagram of the CCP module in PWM mode. For a step by step procedure on how to set up the CCP module for PWM operation, see Section 7.3.3. FIGURE 7-4: SIMPLIFIED PWM BLOCK DIAGRAM The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: PWM period = [(PR2) + 1] • 4 • TOSC • (TMR2 prescale value) PWM frequency is defined as 1 / [PWM period]. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: • TMR2 is cleared • The CCP1 pin is set (exception: if PWM duty cycle = 0%, the CCP1 pin will not be set) • The PWM duty cycle is latched from CCPR1L into CCPR1H Note: CCP1CON<5:4> Duty cycle registers CCPR1L 7.3.2 CCPR1H (Slave) R Comparator Q RC2/CCP1 TMR2 (Note 1) S Clear Timer, CCP1 pin and latch D.C. PR2 Note 1: 8-bit timer is concatenated with 2-bit internal Q clock or 2 bits of the prescaler to create 10-bit time-base. A PWM output (Figure 7-5) has a time base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/period). FIGURE 7-5: PWM OUTPUT The Timer2 postscaler (see Section 6.0) is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. PWM DUTY CYCLE The PWM duty cycle is specified by writing to the CCPR1L register and to the CCP1CON<5:4> bits. Up to 10-bit resolution is available: the CCPR1L contains the eight MSbs and the CCP1CON<5:4> contains the two LSbs. This 10-bit value is represented by CCPR1L:CCP1CON<5:4>. The following equation is used to calculate the PWM duty cycle in time: PWM duty cycle = (CCPR1L:CCP1CON<5:4>) • Tosc • (TMR2 prescale value) TRISC<2> Comparator PWM PERIOD CCPR1L and CCP1CON<5:4> can be written to at any time, but the duty cycle value is not latched into CCPR1H until after a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPR1H is a read-only register. The CCPR1H register and a 2-bit internal latch are used to double buffer the PWM duty cycle. This double buffering is essential for glitchless PWM operation. When the CCPR1H and 2-bit latch match TMR2 concatenated with an internal 2-bit Q clock or 2 bits of the TMR2 prescaler, the CCP1 pin is cleared. Maximum PWM resolution (bits) for a given PWM frequency: Period ( log = Duty Cycle FOSC FPWM ) bits log(2) TMR2 = PR2 Note: TMR2 = Duty Cycle TMR2 = PR2 If the PWM duty cycle value is longer than the PWM period the CCP1 pin will not be cleared. For an example PWM period and duty cycle calculation, see the PICmicro™ Mid-Range Reference Manual, (DS33023). DS35008A-page 36 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 7.3.3 SET-UP FOR PWM OPERATION The following steps should be taken when configuring the CCP module for PWM operation: 1. 2. 3. 4. 5. Set the PWM period by writing to the PR2 register. Set the PWM duty cycle by writing to the CCPR1L register and CCP1CON<5:4> bits. Make the CCP1 pin an output by clearing the TRISC<2> bit. Set the TMR2 prescale value and enable Timer2 by writing to T2CON. Configure the CCP1 module for PWM operation. TABLE 7-3 EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 20 MHz PWM Frequency 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits) TABLE 7-4 16 0xFF 10 4 0xFF 10 1 0xFF 10 1 0x3F 8 1 0x1F 7 1 0x17 5.5 REGISTERS ASSOCIATED WITH PWM AND TIMER2 Value on POR, BOR Value on all other resets Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0Ch PIR1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 8Ch PIE1 — ADIE — — SSPIE CCP1IE TMR2IE TMR1IE -0-- 0000 -0-- 0000 0000 000x 0000 000u 87h TRISC PORTC Data Direction Register 1111 1111 1111 1111 11h TMR2 Timer2 module’s register 0000 0000 0000 0000 92h PR2 Timer2 module’s period register 1111 1111 1111 1111 12h T2CON 15h CCPR1L Capture/Compare/PWM register1 (LSB) xxxx xxxx uuuu uuuu 16h CCPR1H Capture/Compare/PWM register1 (MSB) xxxx xxxx uuuu uuuu 17h Legend: CCP1CON — — TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 — CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000 x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by PWM and Timer2. 1998 Microchip Technology Inc. Preliminary DS35008A-page 37 PIC16C62B/72A NOTES: DS35008A-page 38 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 8.0 SYNCHRONOUS SERIAL PORT (SSP) MODULE 8.1 SSP Module Overview The Synchronous Serial Port (SSP) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be Serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SSP module can operate in one of two modes: • Serial Peripheral Interface (SPI) • Inter-Integrated Circuit (I2C) For more information on SSP operation (including an I2C Overview), refer to the PICmicro™ Mid-Range Reference Manual, (DS33023). Also, refer to Application Note AN578, “Use of the SSP Module in the I 2C MultiMaster Environment.” 1998 Microchip Technology Inc. Preliminary DS35008A-page 39 PIC16C62B/72A FIGURE 8-1: SSPSTAT: SYNC SERIAL PORT STATUS REGISTER (ADDRESS 94h) R/W-0 R/W-0 SMP CKE R-0 R-0 R-0 R-0 R-0 R-0 D/A P S R/W UA BF bit7 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n =Value at POR reset bit 7: SMP: SPI data input sample phase SPI Master Operation 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time SPI Slave Mode SMP must be cleared when SPI is used in slave mode bit 6: CKE: SPI Clock Edge Select CKP = 0 1 = Data transmitted on rising edge of SCK 0 = Data transmitted on falling edge of SCK CKP = 1 1 = Data transmitted on falling edge of SCK 0 = Data transmitted on rising edge of SCK bit 5: D/A: Data/Address bit (I2C mode only) 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address bit 4: P: Stop bit (I2C mode only. This bit is cleared when the SSP module is disabled, or when the Start bit is detected last, SSPEN is cleared) 1 = Indicates that a stop bit has been detected last (this bit is '0' on RESET) 0 = Stop bit was not detected last bit 3: S: Start bit (I2C mode only. This bit is cleared when the SSP module is disabled, or when the Stop bit is detected last, SSPEN is cleared) 1 = Indicates that a start bit has been detected last (this bit is '0' on RESET) 0 = Start bit was not detected last bit 2: R/W: Read/Write bit information (I2C mode only) This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next start bit, stop bit, or ACK bit. 1 = Read 0 = Write bit 1: UA: Update Address (10-bit I2C mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated bit 0: BF: Buffer Full Status bit Receive (SPI and I2C modes) 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Transmit (I2C mode only) 1 = Transmit in progress, SSPBUF is full 0 = Transmit complete, SSPBUF is empty DS35008A-page 40 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A FIGURE 8-2: SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 bit7 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n =Value at POR reset bit 7: WCOL: Write Collision Detect bit 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision bit 6: SSPOV: Receive Overflow Indicator bit In SPI mode 1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in slave mode. The user must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In master operation, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. 0 = No overflow In I2C mode 1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don’t care" in transmit mode. SSPOV must be cleared in software in either mode. 0 = No overflow bit 5: SSPEN: Synchronous Serial Port Enable bit In SPI mode 1 = Enables serial port and configures SCK, SDO, and SDI as serial port pins 0 = Disables serial port and configures these pins as I/O port pins In I2C mode 1 = Enables the serial port and configures the SDA and SCL pins as serial port pins 0 = Disables serial port and configures these pins as I/O port pins In both modes, when enabled, these pins must be properly configured as input or output. bit 4: CKP: Clock Polarity Select bit In SPI mode 1 = Idle state for clock is a high level 0 = Idle state for clock is a low level In I2C mode SCK release control 1 = Enable clock 0 = Holds clock low (clock stretch) (Used to ensure data setup time) bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits 0000 = SPI master operation, clock = FOSC/4 0001 = SPI master operation, clock = FOSC/16 0010 = SPI master operation, clock = FOSC/64 0011 = SPI master operation, clock = TMR2 output/2 0100 = SPI slave mode, clock = SCK pin. SS pin control enabled. 0101 = SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin 0110 = I2C slave mode, 7-bit address 0111 = I2C slave mode, 10-bit address 1011 = I2C firmware controlled master operation (slave idle) 1110 = I2C slave mode, 7-bit address with start and stop bit interrupts enabled 1111 = I2C slave mode, 10-bit address with start and stop bit interrupts enabled 1998 Microchip Technology Inc. Preliminary DS35008A-page 41 PIC16C62B/72A 8.2 SPI Mode This section contains register definitions and operational characteristics of the SPI module. Additional information on SPI operation may be found in the PICmicro™ Mid-Range Reference Manual, (DS33023). 8.2.1 OPERATION OF SSP MODULE IN SPI MODE Note: When the SPI is in Slave Mode with SS pin control enabled, (SSPCON<3:0> = 0100) the SPI module will reset if the SS pin is set to VDD. Note: If the SPI is used in Slave Mode with CKE = '1', then the SS pin control must be enabled. FIGURE 8-3: A block diagram of the SSP Module in SPI Mode is shown in Figure 8-3. SSP BLOCK DIAGRAM (SPI MODE) Internal data bus The SPI mode allows 8-bits of data to be synchronously transmitted and received simultaneously. To accomplish communication, typically three pins are used: Read Write SSPBUF reg • Serial Data Out (SDO)RC5/SDO • Serial Data In (SDI)RC4/SDI/SDA • Serial Clock (SCK)RC3/SCK/SCL Additionally a fourth pin may be used when in a slave mode of operation: • Slave Select (SS)RA5/SS/AN4 SSPSR reg RC4/SDI/SDA shift clock bit0 RC5/SDO When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits in the SSPCON register (SSPCON<5:0>) and SSPSTAT<7:6>. These control bits allow the following to be specified: SS Control Enable RA5/SS/AN4 • • • • Master Operation (SCK is the clock output) Slave Mode (SCK is the clock input) Clock Polarity (Idle state of SCK) Clock Edge (Output data on rising/falling edge of SCK) • Clock Rate (master operation only) • Slave Select Mode (Slave mode only) To enable the serial port, SSP Enable bit, SSPEN (SSPCON<5>) must be set. To reset or reconfigure SPI mode, clear bit SSPEN, re-initialize the SSPCON register, and then set bit SSPEN. This configures the SDI, SDO, SCK, and SS pins as serial port pins. For the pins to behave as the serial port function, they must have their data direction bits (in the TRISC register) appropriately programmed. That is: Edge Select 2 Clock Select SSPM3:SSPM0 4 Edge Select RC3/SCK/ SCL TMR2 output 2 Prescaler TCY 4, 16, 64 TRISC<3> • SDI must have TRISC<4> set • SDO must have TRISC<5> cleared • SCK (master operation) must have TRISC<3> cleared • SCK (Slave mode) must have TRISC<3> set • SS must have TRISA<5> set DS35008A-page 42 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A TABLE 8-1 REGISTERS ASSOCIATED WITH SPI OPERATION Value on POR, BOR Value on all other resets Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF PIR1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 — ADIE — — SSPIE CCP1IE TMR2IE TMR1IE -0-- 0000 -0-- 0000 0Ch 8Ch PIE1 87h TRISC PORTC Data Direction Register 13h SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register 14h SSPCON WCOL 85h TRISA 94h SSPSTAT SSPOV SSPEN — — SMP CKE 1111 1111 1111 1111 CKP SSPM3 SSPM2 xxxx xxxx uuuu uuuu SSPM1 SSPM0 0000 0000 0000 0000 PORTA Data Direction Register D/A 0000 000x 0000 000u P S R/W --11 1111 --11 1111 UA BF 0000 0000 0000 0000 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the SSP in SPI mode. 1998 Microchip Technology Inc. Preliminary DS35008A-page 43 PIC16C62B/72A 8.3 SSP I 2C Operation The SSP module in I 2C mode fully implements all slave functions, except general call support, and provides interrupts on start and stop bits in hardware to facilitate firmware implementations of the master functions. The SSP module implements the standard mode specifications as well as 7-bit and 10-bit addressing. Two pins are used for data transfer. These are the RC3/SCK/SCL pin, which is the clock (SCL), and the RC4/SDI/SDA pin, which is the data (SDA). The user must configure these pins as inputs or outputs through the TRISC<4:3> bits. The SSP module functions are enabled by setting SSP Enable bit SSPEN (SSPCON<5>). FIGURE 8-4: When an address is matched or the data transfer after an address match is received, the hardware automatically will generate the acknowledge (ACK) pulse, and then load the SSPBUF register with the received value currently in the SSPSR register. shift clock SSPSR reg MSb LSb Match detect Addr Match SSPADD reg Start and Stop bit detect Set, Reset S, P bits (SSPSTAT reg) SSP Control Register (SSPCON) SSP Status Register (SSPSTAT) Serial Receive/Transmit Buffer (SSPBUF) SSP Shift Register (SSPSR) - Not directly accessible • SSP Address Register (SSPADD) DS35008A-page 44 There are certain conditions that will cause the SSP module not to give this ACK pulse. These are if either (or both): a) The SSP module has five registers for I2C operation. These are the: • • • • SLAVE MODE In slave mode, the SCL and SDA pins must be configured as inputs (TRISC<4:3> set). The SSP module will override the input state with the output data when required (slave-transmitter). Write SSPBUF reg RC4/ SDI/ SDA Selection of any I 2C mode, with the SSPEN bit set, forces the SCL and SDA pins to be open drain, provided these pins are programmed to inputs by setting the appropriate TRISC bits. 8.3.1 Internal data bus RC3/SCK/SCL • I 2C Slave mode (7-bit address) • I 2C Slave mode (10-bit address) • I 2C Slave mode (7-bit address), with start and stop bit interrupts enabled • I 2C Slave mode (10-bit address), with start and stop bit interrupts enabled • I 2C Firmware controlled master operation, slave is idle Additional information on SSP I2C operation may be found in the PICmicro™ Mid-Range Reference Manual, (DS33023). SSP BLOCK DIAGRAM (I2C MODE) Read The SSPCON register allows control of the I 2C operation. Four mode selection bits (SSPCON<3:0>) allow one of the following I 2C modes to be selected: b) The buffer full bit BF (SSPSTAT<0>) was set before the transfer was received. The overflow bit SSPOV (SSPCON<6>) was set before the transfer was received. In this case, the SSPSR register value is not loaded into the SSPBUF, but bit SSPIF (PIR1<3>) is set. Table 8-2 shows what happens when a data transfer byte is received, given the status of bits BF and SSPOV. The shaded cells show the condition where user software did not properly clear the overflow condition. Flag bit BF is cleared by reading the SSPBUF register while bit SSPOV is cleared through software. The SCL clock input must have a minimum high and low for proper operation. The high and low times of the I2C specification as well as the requirement of the SSP module is shown in timing parameter #100 and parameter #101. Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 8.3.1.1 ADDRESSING Once the SSP module has been enabled, it waits for a START condition to occur. Following the START condition, the 8-bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock (SCL) line. The value of register SSPSR<7:1> is compared to the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match, and the BF and SSPOV bits are clear, the following events occur: a) b) c) d) The SSPSR register value is loaded into the SSPBUF register. The buffer full bit, BF is set. An ACK pulse is generated. SSP interrupt flag bit, SSPIF (PIR1<3>) is set (interrupt is generated if enabled) - on the falling edge of the ninth SCL pulse. In 10-bit address mode, two address bytes need to be received by the slave. The five Most Significant bits (MSbs) of the first address byte specify if this is a 10-bit address. Bit R/W (SSPSTAT<2>) must specify a write so the slave device will receive the second address byte. For a 10-bit address the first byte would equal TABLE 8-2 ‘1111 0 A9 A8 0’, where A9 and A8 are the two MSbs of the address. The sequence of events for 10-bit address is as follows, with steps 7- 9 for slave-transmitter: 1. 2. 3. 4. 5. 6. 7. 8. 9. Receive first (high) byte of Address (bits SSPIF, BF, and bit UA (SSPSTAT<1>) are set). Update the SSPADD register with second (low) byte of Address (clears bit UA and releases the SCL line). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive second (low) byte of Address (bits SSPIF, BF, and UA are set). Update the SSPADD register with the first (high) byte of Address, if match releases SCL line, this will clear bit UA. Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive repeated START condition. Receive first (high) byte of Address (bits SSPIF and BF are set). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. DATA TRANSFER RECEIVED BYTE ACTIONS Status Bits as Data Transfer is Received Set bit SSPIF (SSP Interrupt occurs if enabled) BF SSPOV SSPSR → SSPBUF Generate ACK Pulse 0 0 Yes Yes Yes 1 0 No No Yes 1 1 No No Yes 0 1 Yes No Yes Note:Shaded cells show the conditions where the user software did not properly clear the overflow condition. 1998 Microchip Technology Inc. Preliminary DS35008A-page 45 PIC16C62B/72A 8.3.1.2 When the address byte overflow condition exists, then no acknowledge (ACK) pulse is given. An overflow condition is defined as either bit BF (SSPSTAT<0>) is set or bit SSPOV (SSPCON<6>) is set. RECEPTION When the R/W bit of the address byte is clear and an address match occurs, the R/W bit of the SSPSTAT register is cleared. The received address is loaded into the SSPBUF register. I 2C WAVEFORMS FOR RECEPTION (7-BIT ADDRESS) FIGURE 8-5: Receiving Address Receiving Data R/W=0 Receiving Data ACK ACK ACK A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 SDA SCL An SSP interrupt is generated for each data transfer byte. Flag bit SSPIF (PIR1<3>) must be cleared in software. The SSPSTAT register is used to determine the status of the byte. S 1 2 3 SSPIF (PIR1<3>) BF (SSPSTAT<0>) 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 Cleared in software 9 P Bus Master terminates transfer SSPBUF register is read SSPOV (SSPCON<6>) Bit SSPOV is set because the SSPBUF register is still full. ACK is not sent. DS35008A-page 46 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 8.3.1.3 An SSP interrupt is generated for each data transfer byte. Flag bit SSPIF must be cleared in software, and the SSPSTAT register is used to determine the status of the byte. Flag bit SSPIF is set on the falling edge of the ninth clock pulse. TRANSMISSION When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The ACK pulse will be sent on the ninth bit, and pin RC3/SCK/SCL is held low. The transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then pin RC3/SCK/SCL should be enabled by setting bit CKP (SSPCON<4>). The master must monitor the SCL pin prior to asserting another clock pulse. The slave devices may be holding off the master by stretching the clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time (Figure 8-6). I 2C WAVEFORMS FOR TRANSMISSION (7-BIT ADDRESS) FIGURE 8-6: Receiving Address SDA SCL A7 S As a slave-transmitter, the ACK pulse from the masterreceiver is latched on the rising edge of the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete. When the ACK is latched by the slave, the slave logic is reset (resets SSPSTAT register) and the slave then monitors for another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then pin RC3/SCK/SCL should be enabled by setting bit CKP. A6 1 2 Data in sampled R/W = 1 A5 A4 A3 A2 A1 3 4 5 6 7 8 9 ACK Transmitting Data ACK D7 1 SCL held low while CPU responds to SSPIF D6 D5 D4 D3 D2 D1 D0 2 3 4 5 6 7 8 9 P cleared in software SSPIF (PIR1<3>) BF (SSPSTAT<0>) SSPBUF is written in software From SSP interrupt service routine CKP (SSPCON<4>) Set bit after writing to SSPBUF (the SSPBUF must be written-to before the CKP bit can be set) 1998 Microchip Technology Inc. Preliminary DS35008A-page 47 PIC16C62B/72A 8.3.2 8.3.3 MASTER OPERATION In multi-master operation, the interrupt generation on the detection of the START and STOP conditions allows the determination of when the bus is free. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. The STOP (P) and START (S) bits will toggle based on the START and STOP conditions. Control of the I 2C bus may be taken when bit P (SSPSTAT<4>) is set, or the bus is idle and both the S and P bits clear. When the bus is busy, enabling the SSP Interrupt will generate the interrupt when the STOP condition occurs. Master operation is supported in firmware using interrupt generation on the detection of the START and STOP conditions. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. The STOP (P) and START (S) bits will toggle based on the START and STOP conditions. Control of the I 2C bus may be taken when the P bit is set, or the bus is idle and both the S and P bits are clear. In master operation, the SCL and SDA lines are manipulated in firmware by clearing the corresponding TRISC<4:3> bit(s). The output level is always low, irrespective of the value(s) in PORTC<4:3>. So when transmitting data, a '1' data bit must have the TRISC<4> bit set (input) and a '0' data bit must have the TRISC<4> bit cleared (output). The same scenario is true for the SCL line with the TRISC<3> bit. In multi-master operation, the SDA line must be monitored to see if the signal level is the expected output level. This check only needs to be done when a high level is output. If a high level is expected and a low level is present, the device needs to release the SDA and SCL lines (set TRISC<4:3>). There are two stages where this arbitration can be lost, these are: The following events will cause SSP Interrupt Flag bit, SSPIF, to be set (SSP Interrupt if enabled): • Address Transfer • Data Transfer • START condition • STOP condition • Data transfer byte transmitted/received When the slave logic is enabled, the slave continues to receive. If arbitration was lost during the address transfer stage, communication to the device may be in progress. If addressed an ACK pulse will be generated. If arbitration was lost during the data transfer stage, the device will need to re-transfer the data at a later time. Master operation can be done with either the slave mode idle (SSPM3:SSPM0 = 1011) or with the slave active. When both master operation and slave modes are used, the software needs to differentiate the source(s) of the interrupt. For more information on master operation, see AN578 - Use of the SSP Module in the of I2C Multi-Master Environment. For more information on master operation, see AN554 - Software Implementation of I2C Bus Master. TABLE 8-3 MULTI-MASTER OPERATION REGISTERS ASSOCIATED WITH I2C OPERATION Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other resets 0Bh, 8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u 0Ch PIR1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 8Ch PIE1 — ADIE — — SSPIE CCP1IE TMR2IE TMR1IE -0-- 0000 -0-- 0000 13h SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register xxxx xxxx uuuu uuuu 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 1111 1111 1111 1111 93h SSPADD Synchronous Serial Port 14h SSPCON WCOL 94h SSPSTAT SMP 87h TRISC (I2C mode) Address Register SSPOV SSPEN CKE D/A CKP P SSPM3 SSPM2 SSPM1 SSPM0 S R/W PORTC Data Direction register UA BF Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by SSP module in SPI mode. DS35008A-page 48 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 9.0 ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE Additional information on the A/D module is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). This section applies to the PIC16C72A only. The analog-to-digital (A/D) converter module has five inputs. The A/D allows conversion of an analog input signal to a corresponding 8-bit digital number (refer to Application Note AN546 for use of A/D Converter). The output of the sample and hold is the input into the converter, which generates the result via successive approximation. The analog reference voltage is software selectable to either the device’s positive supply voltage (VDD) or the voltage level on the RA3/AN3/VREF pin. The A/D converter has a unique feature of being able to operate while the device is in SLEEP mode. To operate in sleep, the A/D conversion clock must be derived from the A/D’s internal RC oscillator. FIGURE 9-1: The A/D module has three registers. These registers are: • A/D Result Register (ADRES) • A/D Control Register 0 (ADCON0) • A/D Control Register 1 (ADCON1) A device reset forces all registers to their reset state. This forces the A/D module to be turned off, and any conversion is aborted. The ADCON0 register, shown in Figure 9-1, controls the operation of the A/D module. The ADCON1 register, shown in Figure 9-2, configures the functions of the port pins. The port pins can be configured as analog inputs (RA3 can also be a voltage reference) or as digital I/O. ADCON0 REGISTER (ADDRESS 1Fh) R/W-0 R/W-0 ADCS1 ADCS0 bit7 R/W-0 CHS2 R/W-0 CHS1 R/W-0 CHS0 R/W-0 GO/DONE U-0 — R/W-0 ADON bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7-6: ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (clock derived from an internal RC oscillator) bit 5-3: CHS2:CHS0: Analog Channel Select bits 000 = channel 0, (RA0/AN0) 001 = channel 1, (RA1/AN1) 010 = channel 2, (RA2/AN2) 011 = channel 3, (RA3/AN3) 100 = channel 4, (RA5/AN4) bit 2: GO/DONE: A/D Conversion Status bit If ADON = 1 1 = A/D conversion in progress (setting this bit starts the A/D conversion) 0 = A/D conversion not in progress (This bit is automatically cleared by hardware when the A/D conversion is complete) bit 1: Unimplemented: Read as '0' bit 0: ADON: A/D On bit 1 = A/D converter module is operating 0 = A/D converter module is shutoff and consumes no operating current 1998 Microchip Technology Inc. Preliminary DS35008A-page 49 PIC16C62B/72A FIGURE 9-2: U-0 — bit7 ADCON1 REGISTER (ADDRESS 9Fh) U-0 — U-0 — U-0 — U-0 — R/W-0 PCFG2 R/W-0 PCFG1 R/W-0 PCFG0 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7-3: Unimplemented: Read as '0' bit 2-0: PCFG2:PCFG0: A/D Port Configuration Control bits PCFG2:PCFG0 000 001 010 011 100 101 11x RA0 A A A A A A D RA1 A A A A A A D RA2 A A A A D D D RA5 A A A A D D D RA3 A VREF A VREF A VREF D VREF VDD RA3 VDD RA3 VDD RA3 VDD A = Analog input D = Digital I/O DS35008A-page 50 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 1. The ADRES register contains the result of the A/D conversion. When the A/D conversion is complete, the result is loaded into the ADRES register, the GO/DONE bit (ADCON0<2>) is cleared, and A/D interrupt flag bit ADIF is set. The block diagram of the A/D module is shown in Figure 9-3. The value that is in the ADRES register is not modified for a Power-on Reset. The ADRES register will contain unknown data after a Power-on Reset. 2. After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as an input. To determine acquisition time, see Section 9.1. After this acquisition time has elapsed the A/D conversion can be started. The following steps should be followed for doing an A/D conversion: 3. 4. 5. Configure the A/D module: • Configure analog pins / voltage reference / and digital I/O (ADCON1) • Select A/D input channel (ADCON0) • Select A/D conversion clock (ADCON0) • Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): • Clear ADIF bit • Set ADIE bit • Set GIE bit Wait the required acquisition time. Start conversion: • Set GO/DONE bit (ADCON0) Wait for A/D conversion to complete, by either: • Polling for the GO/DONE bit to be cleared OR 6. 7. FIGURE 9-3: • Waiting for the A/D interrupt Read A/D Result register (ADRES), clear bit ADIF if required. For next conversion, go to step 1 or step 2 as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2TAD is required before next acquisition starts. A/D BLOCK DIAGRAM CHS2:CHS0 100 RA5/AN4 VIN 011 (Input voltage) RA3/AN3/VREF 010 RA2/AN2 A/D Converter 001 RA1/AN1 VDD 000 RA0/AN0 000 or 010 or 100 VREF (Reference voltage) 001 or 011 or 101 PCFG2:PCFG0 1998 Microchip Technology Inc. Preliminary DS35008A-page 51 PIC16C62B/72A 9.1 A/D Acquisition Requirements For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 9-4. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD). The source impedance affects the offset voltage at the analog input (due to pin leakage current). The maximum recommended impedance for analog sources is 10 kΩ. After the analog input channel is selected (changed) this acquisition must be done before the conversion can be started. FIGURE 9-4: To calculate the minimum acquisition time, TACQ, see the PICmicro™ Mid-Range Reference Manual, (DS33023). This equation calculates the acquisition time to within 1/2 LSb error (512 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified accuracy. Note: When the conversion is started, the holding capacitor is disconnected from the input pin. ANALOG INPUT MODEL VDD Rs ANx CPIN 5 pF VA Sampling Switch VT = 0.6V VT = 0.6V RIC ≤ 1k SS RSS CHOLD = DAC capacitance = 51.2 pF I leakage ± 500 nA VSS Legend CPIN = input capacitance VT = threshold voltage I leakage = leakage current at the pin due to various junctions RIC SS CHOLD DS35008A-page 52 = interconnect resistance = sampling switch = sample/hold capacitance (from DAC) Preliminary 6V 5V VDD 4V 3V 2V 5 6 7 8 9 10 11 Sampling Switch (kΩ) 1998 Microchip Technology Inc. PIC16C62B/72A 9.2 Selecting the A/D Conversion Clock The A/D conversion time per bit is defined as TAD. The A/D conversion requires 9.5TAD per 8-bit conversion. The source of the A/D conversion clock is software selectable. The four possible options for TAD are: • • • • 2TOSC 8TOSC 32TOSC Internal RC oscillator Table 9-1 shows the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. The ADCON1 and TRISA registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. Note 1: When reading the port register, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs, will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. Note 2: Analog levels on any pin that is defined as a digital input (including the AN4:AN0 pins), may cause the input buffer to consume current that is out of the devices specification. TAD vs. DEVICE OPERATING FREQUENCIES AD Clock Source (TAD) Operation ADCS1:ADCS0 2TOSC 00 8TOSC 01 32TOSC Configuring Analog Port Pins The A/D operation is independent of the state of the CHS2:CHS0 bits and the TRIS bits. For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time of 1.6 µs. TABLE 9-1 9.3 10 Device Frequency 20 MHz 100 ns(2) ns(2) 400 1.6 µs 5 MHz ns(2) 400 1.6 µs 6.4 µs 1.25 MHz 333.33 kHz 1.6 µs 6 µs 6.4 µs 24 µs(3) 25.6 µs(3) 96 µs(3) 2 - 6 µs(1,4) 2 - 6 µs(1,4) 2 - 6 µs(1) 2 - 6 µs(1,4) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 4 µs. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. When device frequency is greater than 1 MHz, the RC A/D conversion clock source is recommended for sleep operation only. 5: For extended voltage devices (LC), please refer to Electrical Specifications section. RC(5) Legend: Note 1: 2: 3: 4: 11 1998 Microchip Technology Inc. Preliminary DS35008A-page 53 PIC16C62B/72A 9.4 Note: 9.5 A/D Conversions The GO/DONE bit should NOT be set in the same instruction that turns on the A/D. Use of the CCP Trigger An A/D conversion can be started by the “special event trigger” of the CCP2 module. This requires that the CCP2M3:CCP2M0 bits (CCP2CON<3:0>) be programmed as 1011 and that the A/D module is enabled (ADON bit is set). When the trigger occurs, the TABLE 9-2 GO/DONE bit will be set, starting the A/D conversion, and the Timer1 counter will be reset to zero. Timer1 is reset to automatically repeat the A/D acquisition period with minimal software overhead (moving the ADRES to the desired location). The appropriate analog input channel must be selected and the minimum acquisition done before the “special event trigger” sets the GO/DONE bit (starts a conversion). If the A/D module is not enabled (ADON is cleared), then the “special event trigger” will be ignored by the A/D module, but will still reset the Timer1 counter. SUMMARY OF A/D REGISTERS Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other Resets 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u 0Ch PIR1 8Ch PIE1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 ADIE — — SSPIE CCP1IE TMR2IE TMR1IE -0-- 0000 -0-- 0000 1Eh ADRES — A/D Result Register 1Fh ADCON0 ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE — ADON 9Fh ADCON1 — — — — — PCFG2 PCFG1 PCFG0 xxxx xxxx uuuu uuuu 0000 00-0 0000 00-0 ---- -000 ---- -000 --0x 0000 --0u 0000 05h PORTA — — RA5 RA4 RA3 RA2 RA1 RA0 --11 1111 85h TRISA — — PORTA Data Direction Register Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used for A/D conversion. DS35008A-page 54 Preliminary --11 1111 1998 Microchip Technology Inc. PIC16C62B/72A 10.0 SPECIAL FEATURES OF THE CPU other is the Power-up Timer (PWRT), which provides a fixed delay on power-up only, designed to keep the part in reset while the power supply stabilizes. With these two timers on-chip, most applications need no external reset circuitry. The PIC16C62B/72A devices have a host of features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving operating modes and offer code protection. These are: SLEEP mode is designed to offer a very low current power-down mode. The user can wake-up from SLEEP through external reset, Watchdog Timer Wake-up, or through an interrupt. Several oscillator options are also made available to allow the part to fit the application. The RC oscillator option saves system cost while the LP crystal option saves power. A set of configuration bits are used to select various options. • OSC Selection • Reset - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) - Brown-out Reset (BOR) • Interrupts • Watchdog Timer (WDT) • SLEEP • Code protection • ID locations • In-circuit serial programming™ Additional information on special features is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). 10.1 Configuration Bits The configuration bits can be programmed (read as '0') or left unprogrammed (read as '1') to select various device configurations. These bits are mapped in program memory location 2007h. These devices have a Watchdog Timer which can be shut off only through configuration bits. It runs off its own RC oscillator for added reliability. There are two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep the chip in reset until the crystal oscillator is stable. The The user will note that address 2007h is beyond the user program memory space. In fact, it belongs to the special test/configuration memory space (2000h 3FFFh), which can be accessed only during programming. FIGURE 10-1: CONFIGURATION WORD CP1 CP0 CP1 CP0 CP1 CP0 — BODEN CP1 CP0 PWRTE bit13 WDTE FOSC1 FOSC0 bit0 bit 13-8 5-4: CP1:CP0: Code Protection bits (2) 11 = Code protection off 10 = Upper half of program memory code protected 01 = Upper 3/4th of program memory code protected 00 = All memory is code protected bit 7: Unimplemented: Read as '1' bit 6: BODEN: Brown-out Reset Enable bit (1) 1 = BOR enabled 0 = BOR disabled bit 3: PWRTE: Power-up Timer Enable bit (1) 1 = PWRT disabled 0 = PWRT enabled bit 2: WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 1-0: FOSC1:FOSC0: Oscillator Selection bits 11 = RC oscillator 10 = HS oscillator 01 = XT oscillator 00 = LP oscillator Register:CONFIG Address2007h Note 1: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT) regardless of the value of bit PWRTE. Ensure the Power-up Timer is enabled anytime Brown-out Reset is enabled. 2: All of the CP1:CP0 pairs have to be given the same value to enable the code protection scheme listed. 1998 Microchip Technology Inc. Preliminary DS35008A-page 55 PIC16C62B/72A 10.2 Oscillator Configurations 10.2.1 OSCILLATOR TYPES TABLE 10-1 Ranges Tested: The PIC16CXXX can be operated in four different oscillator modes. The user can program two configuration bits (FOSC1 and FOSC0) to select one of these four modes: • • • • LP XT HS RC Low Power Crystal Crystal/Resonator High Speed Crystal/Resonator Resistor/Capacitor 10.2.2 Mode XT 455 kHz 2.0 MHz 4.0 MHz 8.0 MHz 16.0 MHz TABLE 10-2 Osc Type C2(1) Note1: 2: 3: LP XT To internal logic PIC16CXXX FIGURE 10-3: EXTERNAL CLOCK INPUT OPERATION (HS, XT OR LP OSC CONFIGURATION) OSC1 PIC16CXXX Open DS35008A-page 56 OSC2 ± 0.3% ± 0.5% ± 0.5% ± 0.5% ± 0.5% CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR Crystal Freq Cap. Range C1 Cap. Range C2 33 pF 32 kHz 33 pF 200 kHz 15 pF 15 pF 200 kHz 47-68 pF 47-68 pF 1 MHz 15 pF 15 pF 4 MHz 15 pF 15 pF 4 MHz 15 pF 15 pF 8 MHz 15-33 pF 15-33 pF 20 MHz 15-33 pF 15-33 pF These values are for design guidance only. See notes at bottom of page. See Table 10-1 and Table 10-2 for recommended values of C1 and C2. A series resistor (RS) may be required for AT strip cut crystals. RF varies with the crystal chosen. Clock from ext. system HS SLEEP RS(2) Panasonic EFO-A455K04B Murata Erie CSA2.00MG Murata Erie CSA4.00MG Murata Erie CSA8.00MT Murata Erie CSA16.00MX All resonators used did not have built-in capacitors. OSC1 OSC2 OSC2 68 - 100 pF 15 - 68 pF 15 - 68 pF 10 - 68 pF 10 - 22 pF Resonators Used: FIGURE 10-2: CRYSTAL/CERAMIC RESONATOR OPERATION (HS, XT OR LP OSC CONFIGURATION) RF(3) OSC1 68 - 100 pF 15 - 68 pF 15 - 68 pF 10 - 68 pF 10 - 22 pF These values are for design guidance only. See notes at bottom of page. In XT, LP or HS modes a crystal or ceramic resonator is connected to the OSC1/CLKIN and OSC2/CLKOUT pins to establish oscillation (Figure 10-2). The PIC16CXXX Oscillator design requires the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in XT, LP or HS modes, the device can have an external clock source to drive the OSC1/CLKIN pin (Figure 10-3). XTAL Freq 455 kHz 2.0 MHz 4.0 MHz 8.0 MHz 16.0 MHz HS CRYSTAL OSCILLATOR/CERAMIC RESONATORS C1(1) CERAMIC RESONATORS Crystals Used 32 kHz Epson C-001R32.768K-A ± 20 PPM 200 kHz STD XTL 200.000KHz ± 20 PPM 1 MHz ECS ECS-10-13-1 ± 50 PPM 4 MHz ECS ECS-40-20-1 ± 50 PPM 8 MHz EPSON CA-301 8.000M-C ± 30 PPM 20 MHz EPSON CA-301 20.000M-C ± 30 PPM Note 1: Recommended values of C1 and C2 are identical to the ranges tested (Table 10-1). 2: Higher capacitance increases the stability of oscillator but also increases the start-up time. 3: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 4: Rs may be required in HS mode as well as XT mode to avoid overdriving crystals with low drive level specification. Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 10.2.3 10.3 RC OSCILLATOR For timing insensitive applications the “RC” device option offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values, and the operating temperature. In addition to this, the oscillator frequency will vary from unit to unit due to normal process parameter variation. Furthermore, the difference in lead frame capacitance between package types will also affect the oscillation frequency, especially for low CEXT values. The user also needs to take into account variation due to tolerance of external R and C components used. Figure 10-4 shows how the R/C combination is connected to the PIC16CXXX. FIGURE 10-4: RC OSCILLATOR MODE VDD Rext OSC1 Cext Internal clock PIC16CXX VSS Fosc/4 Recommended values: OSC2/CLKOUT 3 kΩ ≤ Rext ≤ 100 kΩ Cext > 20pF 1998 Microchip Technology Inc. Reset The PIC16CXXX differentiates between various kinds of reset: • • • • • • Power-on Reset (POR) MCLR reset during normal operation MCLR reset during SLEEP WDT Reset (during normal operation) WDT Wake-up (during SLEEP) Brown-out Reset (BOR) Some registers are not affected in any reset condition; their status is unknown on POR and unchanged in any other reset. Most other registers are reset to a “reset state” on Power-on Reset (POR), on the MCLR and WDT Reset, on MCLR reset during SLEEP, and Brownout Reset (BOR). They are not affected by a WDT Wake-up, which is viewed as the resumption of normal operation. The TO and PD bits are set or cleared differently in different reset situations as indicated in Table 10-4. These bits are used in software to determine the nature of the reset. See Table 10-6 for a full description of reset states of all registers. A simplified block diagram of the on-chip reset circuit is shown in Figure 10-5. The PICmicros have a MCLR noise filter in the MCLR reset path. The filter will detect and ignore small pulses. It should be noted that a WDT Reset does not drive MCLR pin low. Preliminary DS35008A-page 57 PIC16C62B/72A FIGURE 10-5: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT External Reset MCLR WDT Module SLEEP WDT Time-out Reset VDD rise detect Power-on Reset VDD Brown-out Reset S BODEN OST/PWRT OST Chip_Reset R 10-bit Ripple counter Q OSC1 (1) On-chip RC OSC PWRT 10-bit Ripple counter Enable PWRT Enable OST Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin. DS35008A-page 58 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 10.4 10.5 Power-On Reset (POR) A Power-on Reset pulse is generated on-chip when VDD rise is detected (in the range of 1.5V - 2.1V). To take advantage of the POR, just tie the MCLR pin directly (or through a resistor) to VDD. This will eliminate external RC components usually needed to create a Power-on Reset. A maximum rise time for VDD is specified (parameter D004). For a slow rise time, see Figure 10-6. When the device starts normal operation (exits the reset condition), device operating parameters (voltage, frequency, temperature,...) must be met to ensure operation. If these conditions are not met, the device must be held in reset until the operating conditions are met. Brown-out Reset may be used to meet the start-up conditions. FIGURE 10-6: EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW VDD POWER-UP) VDD D The Power-up Timer provides a fixed nominal time-out (parameter #33), on power-up only, from the POR. The Power-up Timer operates on an internal RC oscillator. The chip is kept in reset as long as the PWRT is active. The PWRT’s time delay allows VDD to rise to an acceptable level. A configuration bit is provided to enable/disable the PWRT. The power-up time delay will vary from chip to chip due to VDD, temperature, and process variation. See DC parameters for details. 10.6 R1 MCLR C PIC16CXXX Note 1: External Power-on Reset circuit is required only if VDD power-up slope is too slow. The diode D helps discharge the capacitor quickly when VDD powers down. 2: R < 40 kΩ is recommended to make sure that voltage drop across R does not violate the device’s electrical specification. 3: R1 = 100Ω to 1 kΩ will limit any current flowing into MCLR from external capacitor C in the event of MCLR/VPP pin breakdown due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). 1998 Microchip Technology Inc. Oscillator Start-up Timer (OST) The Oscillator Start-up Timer (OST) provides 1024 oscillator cycle (from OSC1 input) delay after the PWRT delay is over (parameter #32). This ensures that the crystal oscillator or resonator has started and stabilized. The OST time-out is invoked only for XT, LP and HS modes and only on Power-on Reset or wake-up from SLEEP. 10.7 R Power-up Timer (PWRT) Brown-Out Reset (BOR) A configuration bit, BODEN, can disable (if clear/programmed) or enable (if set) the Brown-out Reset circuitry. If VDD falls below parameter D005 for greater than parameter #35, the brown-out situation will reset the chip. A reset may not occur if VDD falls below parameter D005 for less than parameter #35. The chip will remain in Brown-out Reset until VDD rises above BVDD. The Power-up Timer will then be invoked and will keep the chip in RESET an additional time delay (parameter #33). If VDD drops below BVDD while the Power-up Timer is running, the chip will go back into a Brown-out Reset and the Power-up Timer will be initialized. Once VDD rises above BVDD, the Power-up Timer will execute the additional time delay. The Power-up Timer should always be enabled when Brown-out Reset is enabled. Preliminary DS35008A-page 59 PIC16C62B/72A 10.8 Time-out Sequence 10.9 On power-up the time-out sequence is as follows: First PWRT time-out is invoked after the POR time delay has expired. Then OST is activated. The total time-out will vary based on oscillator configuration and the status of the PWRT. For example, in RC mode with the PWRT disabled, there will be no time-out at all. Figure 10-7, Figure 10-8, Figure 10-9 and Figure 10-10 depict timeout sequences on power-up. The Power Control/Status Register, PCON has up to two bits, depending upon the device. Bit0 is Brown-out Reset Status bit, BOR. If the BODEN configuration bit is set, BOR is ’1’ on Power-on Reset. If the BODEN configuration bit is clear, BOR is unknown on Power-on Reset. The BOR status bit is a "don't care" and is not necessarily predictable if the brown-out circuit is disabled (the BODEN configuration bit is clear). BOR must then be set by the user and checked on subsequent resets to see if it is clear, indicating a brown-out has occurred. Since the time-outs occur from the POR pulse, if MCLR is kept low long enough, the time-outs will expire. Then bringing MCLR high will begin execution immediately (Figure 10-9). This is useful for testing purposes or to synchronize more than one PIC16CXXX device operating in parallel. Bit1 is POR (Power-on Reset Status bit). It is cleared on a Power-on Reset and unaffected otherwise. The user must set this bit following a Power-on Reset. Table 10-5 shows the reset conditions for some special function registers, while Table 10-6 shows the reset conditions for all the registers. TABLE 10-3 Power Control/Status Register (PCON) TIME-OUT IN VARIOUS SITUATIONS Power-up Oscillator Configuration Brown-out Wake-up from SLEEP PWRTE = 0 PWRTE = 1 XT, HS, LP 72 ms + 1024TOSC 1024TOSC 72 ms + 1024TOSC 1024TOSC RC 72 ms — 72 ms — TABLE 10-4 STATUS BITS AND THEIR SIGNIFICANCE POR BOR TO PD 0 x 1 1 Power-on Reset 0 x 0 x Illegal, TO is set on POR 0 x x 0 Illegal, PD is set on POR 1 0 1 1 Brown-out Reset 1 1 0 1 WDT Reset 1 1 0 0 WDT Wake-up 1 1 u u MCLR Reset during normal operation 1 1 1 0 MCLR Reset during SLEEP or interrupt wake-up from SLEEP TABLE 10-5 RESET CONDITION FOR SPECIAL REGISTERS Program Counter STATUS Register PCON Register Power-on Reset 000h 0001 1xxx ---- --0x MCLR Reset during normal operation 000h 000u uuuu ---- --uu MCLR Reset during SLEEP 000h 0001 0uuu ---- --uu WDT Reset 000h 0000 1uuu ---- --uu PC + 1 uuu0 0uuu ---- --uu 000h 0001 1uuu ---- --u0 PC + 1(1) uuu1 0uuu ---- --uu Condition WDT Wake-up Brown-out Reset Interrupt wake-up from SLEEP Legend: u = unchanged, x = unknown, - = unimplemented bit read as '0'. Note 1: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). DS35008A-page 60 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A TABLE 10-6 Register INITIALIZATION CONDITIONS FOR ALL REGISTERS Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets WDT Reset Wake-up via WDT or Interrupt W 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu INDF 62B 72A N/A N/A N/A TMR0 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu PCL 62B 72A 0000h 0000h PC + 1(2) STATUS 62B 72A 0001 1xxx 000q quuu(3) uuuq quuu(3) FSR 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu PORTA(4) 62B 72A --0x 0000 --0u 0000 --uu uuuu PORTB(5) 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu PORTC(5) 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu PCLATH 62B 72A ---0 0000 ---0 0000 ---u uuuu INTCON 62B 72A 0000 000x 0000 000u uuuu uuuu(1) 62B 72A ---- 0000 ---- 0000 ---- uuuu(1) 62B 72A -0-- 0000 -0-- 0000 -u-- uuuu(1) TMR1L 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu TMR1H 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu T1CON 62B 72A --00 0000 --uu uuuu --uu uuuu TMR2 62B 72A 0000 0000 0000 0000 uuuu uuuu T2CON 62B 72A -000 0000 -000 0000 -uuu uuuu SSPBUF 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu SSPCON 62B 72A 0000 0000 0000 0000 uuuu uuuu CCPR1L 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu CCPR1H 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu PIR1 CCP1CON 62B 72A --00 0000 --00 0000 --uu uuuu ADRES 62B 72A xxxx xxxx uuuu uuuu uuuu uuuu ADCON0 62B 72A 0000 00-0 0000 00-0 uuuu uu-u OPTION_REG 62B 72A 1111 1111 1111 1111 uuuu uuuu TRISA 62B 72A --11 1111 --11 1111 --uu uuuu TRISB 62B 72A 1111 1111 1111 1111 uuuu uuuu TRISC 62B 72A 1111 1111 1111 1111 uuuu uuuu 62B 72A ---- 0000 ---- 0000 ---- uuuu PIE1 62B 72A -0-- 0000 -0-- 0000 -u-- uuuu PCON 62B 72A ---- --0q ---- --uq ---- --uq PR2 62B 72A 1111 1111 1111 1111 1111 1111 SSPADD 62B 72A 0000 0000 0000 0000 uuuu uuuu SSPSTAT 62B 72A 0000 0000 0000 0000 uuuu uuuu ADCON1 62B 72A ---- -000 ---- -000 ---- -uuu Legend: Note 1: 2: 3: 4: 5: u = unchanged, x = unknown, - = unimplemented bit, read as '0', q = value depends on condition One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). See Table 10-5 for reset value for specific condition. On any device reset, these pins are configured as inputs. This is the value that will be in the port output latch. 1998 Microchip Technology Inc. Preliminary DS35008A-page 61 PIC16C62B/72A FIGURE 10-7: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD) VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 10-8: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 10-9: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET DS35008A-page 62 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A FIGURE 10-10: SLOW RISE TIME (MCLR TIED TO VDD) 5V VDD 1V 0V MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET 1998 Microchip Technology Inc. Preliminary DS35008A-page 63 PIC16C62B/72A 10.10 Interrupts The RB0/INT pin interrupt, the RB port change interrupt and the TMR0 overflow interrupt flags are contained in the INTCON register. The PIC16C62B/72A devices have up to 7 sources of interrupt. The interrupt control register (INTCON) records individual interrupt requests in flag bits. It also has individual and global interrupt enable bits. Note: The peripheral interrupt flags are contained in the special function registers PIR1 and PIR2. The corresponding interrupt enable bits are contained in special function registers PIE1 and PIE2, and the peripheral interrupt enable bit is contained in special function register INTCON. Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit. When an interrupt is responded to, the GIE bit is cleared to disable any further interrupt, the return address is pushed onto the stack and the PC is loaded with 0004h. Once in the interrupt service routine the source(s) of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bit(s) must be cleared in software before re-enabling interrupts to avoid recursive interrupts. A global interrupt enable bit, GIE (INTCON<7>) enables (if set) all un-masked interrupts or disables (if cleared) all interrupts. When bit GIE is enabled, and an interrupt’s flag bit and mask bit are set, the interrupt will vector immediately. Individual interrupts can be disabled through their corresponding enable bits in various registers. Individual interrupt bits are set regardless of the status of the GIE bit. The GIE bit is cleared on reset. For external interrupt events, such as the INT pin or PORTB change interrupt, the interrupt latency will be three or four instruction cycles. The exact latency depends when the interrupt event occurs. The latency is the same for one or two cycle instructions. Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit The “return from interrupt” instruction, RETFIE, exits the interrupt routine as well as sets the GIE bit, which re-enables interrupts. FIGURE 10-11: INTERRUPT LOGIC T0IF T0IE INTF INTE ADIF(1) ADIE(1) SSPIF SSPIE CCP1IF CCP1IE Wake-up (If in SLEEP mode) Interrupt to CPU RBIF RBIE PEIE GIE TMR2IF TMR2IE TMR1IF TMR1IE Note 1: A/D not implemented on the PIC16C62B. DS35008A-page 64 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 10.10.1 INT INTERRUPT 10.11 External interrupt on RB0/INT pin is edge triggered: either rising if bit INTEDG (OPTION_REG<6>) is set, or falling, if the INTEDG bit is clear. When a valid edge appears on the RB0/INT pin, flag bit INTF (INTCON<1>) is set. This interrupt can be disabled by clearing enable bit INTE (INTCON<4>). Flag bit INTF must be cleared in software in the interrupt service routine before re-enabling this interrupt. The INT interrupt can wake-up the processor from SLEEP, if bit INTE was set prior to going into SLEEP. The status of global interrupt enable bit GIE decides whether or not the processor branches to the interrupt vector following wake-up. See Section 10.13 for details on SLEEP mode. During an interrupt, only the return PC value is saved on the stack. Typically, users may wish to save key registers during an interrupt, i.e., W register and STATUS register. This will have to be implemented in software. 10.10.2 TMR0 INTERRUPT An overflow (FFh → 00h) in the TMR0 register will set flag bit T0IF (INTCON<2>). The interrupt can be enabled/disabled by setting/clearing enable bit T0IE (INTCON<5>). (Section 4.0) Example 10-1 stores and restores the W and STATUS registers. The register, W_TEMP, must be defined in each bank and must be defined at the same offset from the bank base address (i.e., if W_TEMP is defined at 0x20 in bank 0, it must also be defined at 0xA0 in bank 1). The example: a) b) c) d) e) f) 10.10.3 PORTB INTCON CHANGE Context Saving During Interrupts Stores the W register. Stores the STATUS register in bank 0. Stores the PCLATH register. Executes the interrupt service routine code (User-generated). Restores the STATUS register (and bank select bit). Restores the W and PCLATH registers. An input change on PORTB<7:4> sets flag bit RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit RBIE (INTCON<4>). (Section 3.2) EXAMPLE 10-1: SAVING STATUS, W, AND PCLATH REGISTERS IN RAM MOVWF SWAPF CLRF MOVWF MOVF MOVWF CLRF BCF MOVF MOVWF : :(ISR) : MOVF MOVWF SWAPF W_TEMP STATUS,W STATUS STATUS_TEMP PCLATH, W PCLATH_TEMP PCLATH STATUS, IRP FSR, W FSR_TEMP ;Copy W to TEMP register, could be bank one or zero ;Swap status to be saved into W ;bank 0, regardless of current bank, Clears IRP,RP1,RP0 ;Save status to bank zero STATUS_TEMP register ;Only required if using pages 1, 2 and/or 3 ;Save PCLATH into W ;Page zero, regardless of current page ;Return to Bank 0 ;Copy FSR to W ;Copy FSR from W to FSR_TEMP PCLATH_TEMP, W PCLATH STATUS_TEMP,W MOVWF SWAPF SWAPF STATUS W_TEMP,F W_TEMP,W ;Restore PCLATH ;Move W into PCLATH ;Swap STATUS_TEMP register into W ;(sets bank to original state) ;Move W into STATUS register ;Swap W_TEMP ;Swap W_TEMP into W 1998 Microchip Technology Inc. Preliminary DS35008A-page 65 PIC16C62B/72A 10.12 Watchdog Timer (WDT) WDT time-out period values may be found in the Electrical Specifications section under parameter #31. Values for the WDT prescaler (actually a postscaler, but shared with the Timer0 prescaler) may be assigned using the OPTION_REG register. The Watchdog Timer is as a free running on-chip RC oscillator which does not require any external components. This RC oscillator is separate from the RC oscillator of the OSC1/CLKIN pin. That means that the WDT will run, even if the clock on the OSC1/CLKIN and OSC2/CLKOUT pins of the device has been stopped, for example, by execution of a SLEEP instruction. During normal operation, a WDT time-out generates a device RESET (Watchdog Timer Reset). If the device is in SLEEP mode, a WDT time-out causes the device to wake-up and continue with normal operation (Watchdog Timer Wake-up). The TO bit in the STATUS register will be cleared upon a Watchdog Timer time-out. Note: The CLRWDT and SLEEP instructions clear the WDT and the postscaler, if assigned to the WDT, and prevent it from timing out and generating a device RESET condition. Note: When a CLRWDT instruction is executed and the prescaler is assigned to the WDT, the prescaler count will be cleared, but the prescaler assignment is not changed. . The WDT can be permanently disabled by clearing configuration bit WDTE (Section 10.1). FIGURE 10-12: WATCHDOG TIMER BLOCK DIAGRAM From TMR0 Clock Source (Figure 4-2) 0 WDT Timer Postscaler M U X 1 8 8 - to - 1 MUX PS2:PS0 PSA WDT Enable Bit To TMR0 (Figure 4-2) 0 1 MUX PSA WDT Time-out Note: PSA and PS2:PS0 are bits in the OPTION_REG register. FIGURE 10-13: SUMMARY OF WATCHDOG TIMER REGISTERS Address Name 2007h Config. bits 81h OPTION_REG Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (1) BODEN(1) CP1 CP0 PWRTE(1) WDTE FOSC1 FOSC0 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 Legend: Shaded cells are not used by the Watchdog Timer. Note 1: See Figure 10-1 for operation of these bits. DS35008A-page 66 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 10.13 Power-down Mode (SLEEP) Other peripherals cannot generate interrupts since during SLEEP, no on-chip clocks are present. Power-down mode is entered by executing a SLEEP instruction. If enabled, the Watchdog Timer will be cleared but keeps running, the PD bit (STATUS<3>) is cleared, the TO (STATUS<4>) bit is set, and the oscillator driver is turned off. The I/O ports maintain the status they had, before the SLEEP instruction was executed (driving high, low, or hi-impedance). For lowest current consumption in this mode, place all I/O pins at either VDD, or VSS, ensure no external circuitry is drawing current from the I/O pin, power-down the A/D, disable external clocks. Pull all I/O pins, that are hi-impedance inputs, high or low externally to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS for lowest current consumption. The contribution from on-chip pull-ups on PORTB should be considered. The MCLR pin must be at a logic high level (VIHMC). 10.13.1 WAKE-UP FROM SLEEP The device can wake up from SLEEP through one of the following events: 1. 2. 3. External reset input on MCLR pin. Watchdog Timer Wake-up (if WDT was enabled). Interrupt from INT pin, RB port change, or some Peripheral Interrupts. External MCLR Reset will cause a device reset. All other events are considered a continuation of program execution and cause a "wake-up". The TO and PD bits in the STATUS register can be used to determine the cause of device reset. The PD bit, which is set on power-up, is cleared when SLEEP is invoked. The TO bit is cleared if a WDT time-out occurred (and caused wake-up). The following peripheral interrupts can wake the device from SLEEP: 1. 2. 3. 4. 5. 6. When the SLEEP instruction is being executed, the next instruction (PC + 1) is pre-fetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up is regardless of the state of the GIE bit. If the GIE bit is clear (disabled), the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEP instruction. 10.13.2 WAKE-UP USING INTERRUPTS When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: • If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT postscaler will not be cleared, the TO bit will not be set and PD bits will not be cleared. • If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake up from sleep. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT postscaler will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. To ensure that the WDT is cleared, a CLRWDT instruction should be executed before a SLEEP instruction. TMR1 interrupt. Timer1 must be operating as an asynchronous counter. CCP capture mode interrupt. Special event trigger (Timer1 in asynchronous mode using an external clock). SSP (Start/Stop) bit detect interrupt. SSP transmit or receive in slave mode (SPI/I2C). USART RX or TX (synchronous slave mode). 1998 Microchip Technology Inc. Preliminary DS35008A-page 67 PIC16C62B/72A FIGURE 10-14: WAKE-UP FROM SLEEP THROUGH INTERRUPT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 TOST(2) CLKOUT(4) INT pin INTF flag (INTCON<1>) Interrupt Latency (Note 2) GIE bit (INTCON<7>) Processor in SLEEP INSTRUCTION FLOW PC PC Instruction fetched Inst(PC) = SLEEP Instruction executed Inst(PC - 1) Note 1: 2: 3: 4: 10.14 PC+1 PC+2 PC+2 Inst(PC + 1) Inst(PC + 2) SLEEP Inst(PC + 1) PC + 2 Dummy cycle 0004h 0005h Inst(0004h) Inst(0005h) Dummy cycle Inst(0004h) XT, HS or LP oscillator mode assumed. TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode. GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line. CLKOUT is not available in these osc modes, but shown here for timing reference. Program Verification/Code Protection If the code protection bit(s) have not been programmed, the on-chip program memory can be read out for verification purposes. Note: 10.15 Microchip does not recommend code protecting windowed devices. ID Locations Four memory locations (2000h - 2003h) are designated as ID locations where the user can store checksum or other code-identification numbers. These locations are not accessible during normal execution but are readable and writable during program/verify. It is recommended that only the 4 least significant bits of the ID location are used. For ROM devices, these values are submitted along with the ROM code. 10.16 In-Circuit Serial Programming™ PIC16CXXX microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data, and three other lines for power, ground, and the programming voltage. This allows customers to manufacture boards with unprogrammed devices, and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. For complete details of serial programming, please refer to the In-Circuit Serial Programming (ICSP™) Guide, DS30277. DS35008A-page 68 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 11.0 INSTRUCTION SET SUMMARY Each PIC16CXXX instruction is a 14-bit word divided into an OPCODE which specifies the instruction type and one or more operands which further specify the operation of the instruction. The PIC16CXX instruction set summary in Table 11-2 lists byte-oriented, bit-oriented, and literal and control operations. Table 11-1 shows the opcode field descriptions. For byte-oriented instructions, 'f' represents a file register designator and 'd' represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If 'd' is zero, the result is placed in the W register. If 'd' is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, 'b' represents a bit field designator which selects the number of the bit affected by the operation, while 'f' represents the number of the file in which the bit is located. execution time is 1 µs. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 µs. Table 11-2 lists the instructions recognized by the MPASM assembler. Figure 11-1 shows the general formats that the instructions can have. Note: All examples use the following format to represent a hexadecimal number: 0xhh where h signifies a hexadecimal digit. FIGURE 11-1: GENERAL FORMAT FOR INSTRUCTIONS Byte-oriented file register operations 13 8 7 6 OPCODE d f (FILE #) For literal and control operations, 'k' represents an eight or eleven bit constant or literal value. TABLE 11-1 Field f W b k x d PC TO PD Z DC C Bit-oriented file register operations 13 10 9 7 6 OPCODE b (BIT #) f (FILE #) Description Register file address (0x00 to 0x7F) Working register (accumulator) Bit address within an 8-bit file register Literal field, constant data or label Don't care location (= 0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. Destination select; d = 0: store result in W, d = 1: store result in file register f. Default is d = 1 Program Counter Time-out bit Power-down bit Zero bit Digit Carry bit Carry bit • Byte-oriented operations • Bit-oriented operations • Literal and control operations 0 d = 0 for destination W d = 1 for destination f f = 7-bit file register address OPCODE FIELD DESCRIPTIONS The instruction set is highly orthogonal and is grouped into three basic categories: To maintain upward compatibility with future PIC16CXXX products, do not use the OPTION and TRIS instructions. 0 b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 8 7 OPCODE 0 k (literal) k = 8-bit immediate value CALL and GOTO instructions only 13 11 OPCODE 10 0 k (literal) k = 11-bit immediate value A description of each instruction is available in the PICmicro™ Mid-Range Reference Manual, (DS33023). All instructions are executed within one single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In this case, the execution takes two instruction cycles with the second cycle executed as a NOP. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction 1998 Microchip Technology Inc. Preliminary DS35008A-page 69 PIC16C62B/72A TABLE 11-2 PIC16CXXX INSTRUCTION SET Mnemonic, Operands Description Cycles 14-Bit Opcode MSb LSb Status Affected Notes BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF f, d f, d f f, d f, d f, d f, d f, d f, d f, d f f, d f, d f, d f, d f, d Add W and f AND W with f Clear f Clear W Complement f Decrement f Decrement f, Skip if 0 Increment f Increment f, Skip if 0 Inclusive OR W with f Move f Move W to f No Operation Rotate Left f through Carry Rotate Right f through Carry Subtract W from f Swap nibbles in f Exclusive OR W with f 1 1 1 1 1 1 1(2) 1 1(2) 1 1 1 1 1 1 1 1 1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0111 0101 0001 0001 1001 0011 1011 1010 1111 0100 1000 0000 0000 1101 1100 0010 1110 0110 dfff dfff lfff 0xxx dfff dfff dfff dfff dfff dfff dfff lfff 0xx0 dfff dfff dfff dfff dfff ffff ffff ffff xxxx ffff ffff ffff ffff ffff ffff ffff ffff 0000 ffff ffff ffff ffff ffff C,DC,Z Z Z Z Z Z Z Z Z C C C,DC,Z Z 1,2 1,2 2 1,2 1,2 1,2,3 1,2 1,2,3 1,2 1,2 1,2 1,2 1,2 1,2 1,2 BIT-ORIENTED FILE REGISTER OPERATIONS BCF BSF BTFSC BTFSS f, b f, b f, b f, b Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set 1 1 1 (2) 1 (2) 01 01 01 01 00bb 01bb 10bb 11bb bfff bfff bfff bfff ffff ffff ffff ffff 1 1 2 1 2 1 1 2 2 2 1 1 1 11 11 10 00 10 11 11 00 11 00 00 11 11 111x 1001 0kkk 0000 1kkk 1000 00xx 0000 01xx 0000 0000 110x 1010 kkkk kkkk kkkk 0110 kkkk kkkk kkkk 0000 kkkk 0000 0110 kkkk kkkk kkkk kkkk kkkk 0100 kkkk kkkk kkkk 1001 kkkk 1000 0011 kkkk kkkk 1,2 1,2 3 3 LITERAL AND CONTROL OPERATIONS ADDLW ANDLW CALL CLRWDT GOTO IORLW MOVLW RETFIE RETLW RETURN SLEEP SUBLW XORLW k k k k k k k k k Add literal and W AND literal with W Call subroutine Clear Watchdog Timer Go to address Inclusive OR literal with W Move literal to W Return from interrupt Return with literal in W Return from Subroutine Go into standby mode Subtract W from literal Exclusive OR literal with W C,DC,Z Z TO,PD Z TO,PD C,DC,Z Z Note 1: When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. DS35008A-page 70 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 12.0 DEVELOPMENT SUPPORT 12.1 Development Tools The PICmicrο microcontrollers are supported with a full range of hardware and software development tools: • MPLAB™-ICE Real-Time In-Circuit Emulator • ICEPIC Low-Cost PIC16C5X and PIC16CXXX In-Circuit Emulator • PRO MATE II Universal Programmer • PICSTART Plus Entry-Level Prototype Programmer • SIMICE • PICDEM-1 Low-Cost Demonstration Board • PICDEM-2 Low-Cost Demonstration Board • PICDEM-3 Low-Cost Demonstration Board • MPASM Assembler • MPLAB SIM Software Simulator • MPLAB-C17 (C Compiler) • Fuzzy Logic Development System (fuzzyTECH−MP) • KEELOQ® Evaluation Kits and Programmer 12.2 MPLAB-ICE: High Performance Universal In-Circuit Emulator with MPLAB IDE The MPLAB-ICE Universal In-Circuit Emulator is intended to provide the product development engineer with a complete microcontroller design tool set for PICmicro microcontrollers (MCUs). MPLAB-ICE is supplied with the MPLAB Integrated Development Environment (IDE), which allows editing, “make” and download, and source debugging from a single environment. Interchangeable processor modules allow the system to be easily reconfigured for emulation of different processors. The universal architecture of the MPLAB-ICE allows expansion to support all new Microchip microcontrollers. The MPLAB-ICE Emulator System has been designed as a real-time emulation system with advanced features that are generally found on more expensive development tools. The PC compatible 386 (and higher) machine platform and Microsoft Windows 3.x or Windows 95 environment were chosen to best make these features available to you, the end user. MPLAB-ICE is available in two versions. MPLAB-ICE 1000 is a basic, low-cost emulator system with simple trace capabilities. It shares processor modules with the MPLAB-ICE 2000. This is a full-featured emulator system with enhanced trace, trigger, and data monitoring features. Both systems will operate across the entire operating speed reange of the PICmicro MCU. 1998 Microchip Technology Inc. 12.3 ICEPIC: Low-Cost PICmicro™ In-Circuit Emulator ICEPIC is a low-cost in-circuit emulator solution for the Microchip PIC12CXXX, PIC16C5X and PIC16CXXX families of 8-bit OTP microcontrollers. ICEPIC is designed to operate on PC-compatible machines ranging from 386 through Pentium based machines under Windows 3.x, Windows 95, or Windows NT environment. ICEPIC features real time, nonintrusive emulation. 12.4 PRO MATE II: Universal Programmer The PRO MATE II Universal Programmer is a full-featured programmer capable of operating in stand-alone mode as well as PC-hosted mode. PRO MATE II is CE compliant. The PRO MATE II has programmable VDD and VPP supplies which allows it to verify programmed memory at VDD min and VDD max for maximum reliability. It has an LCD display for displaying error messages, keys to enter commands and a modular detachable socket assembly to support various package types. In standalone mode the PRO MATE II can read, verify or program PIC12CXXX, PIC14C000, PIC16C5X, PIC16CXXX and PIC17CXX devices. It can also set configuration and code-protect bits in this mode. 12.5 PICSTART Plus Entry Level Development System The PICSTART programmer is an easy-to-use, lowcost prototype programmer. It connects to the PC via one of the COM (RS-232) ports. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. PICSTART Plus is not recommended for production programming. PICSTART Plus supports all PIC12CXXX, PIC14C000, PIC16C5X, PIC16CXXX and PIC17CXX devices with up to 40 pins. Larger pin count devices such as the PIC16C923, PIC16C924 and PIC17C756 may be supported with an adapter socket. PICSTART Plus is CE compliant. 12.6 SIMICE Entry-Level Hardware Simulator SIMICE is an entry-level hardware development system designed to operate in a PC-based environment with Microchip’s simulator MPLAB™-SIM. Both SIMICE and MPLAB-SIM run under Microchip Technology’s MPLAB Integrated Development Environment (IDE) software. Specifically, SIMICE provides hardware simulation for Microchip’s PIC12C5XX, PIC12CE5XX, and PIC16C5X families of PICmicro™ 8-bit microcontrollers. SIMICE works in conjunction with MPLAB-SIM to provide non-real-time I/O port emulation. SIMICE enables a developer to run simulator code for driving the target system. In addition, the target system can DS35008A-page 71 PIC16C62B/72A provide input to the simulator code. This capability allows for simple and interactive debugging without having to manually generate MPLAB-SIM stimulus files. SIMICE is a valuable debugging tool for entrylevel system development. 12.9 PICDEM-3 Low-Cost PIC16CXXX Demonstration Board The PICDEM-1 is a simple board which demonstrates the capabilities of several of Microchip’s microcontrollers. The microcontrollers supported are: PIC16C5X (PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X, PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All necessary hardware and software is included to run basic demo programs. The users can program the sample microcontrollers provided with the PICDEM-1 board, on a PRO MATE II or PICSTART-Plus programmer, and easily test firmware. The user can also connect the PICDEM-1 board to the MPLAB-ICE emulator and download the firmware to the emulator for testing. Additional prototype area is available for the user to build some additional hardware and connect it to the microcontroller socket(s). Some of the features include an RS-232 interface, a potentiometer for simulated analog input, push-button switches and eight LEDs connected to PORTB. The PICDEM-3 is a simple demonstration board that supports the PIC16C923 and PIC16C924 in the PLCC package. It will also support future 44-pin PLCC microcontrollers with a LCD Module. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM-3 board, on a PRO MATE II programmer or PICSTART Plus with an adapter socket, and easily test firmware. The MPLAB-ICE emulator may also be used with the PICDEM-3 board to test firmware. Additional prototype area has been provided to the user for adding hardware and connecting it to the microcontroller socket(s). Some of the features include an RS-232 interface, push-button switches, a potentiometer for simulated analog input, a thermistor and separate headers for connection to an external LCD module and a keypad. Also provided on the PICDEM-3 board is an LCD panel, with 4 commons and 12 segments, that is capable of displaying time, temperature and day of the week. The PICDEM-3 provides an additional RS-232 interface and Windows 3.1 software for showing the demultiplexed LCD signals on a PC. A simple serial interface allows the user to construct a hardware demultiplexer for the LCD signals. 12.8 12.10 12.7 PICDEM-1 Low-Cost PICmicro Demonstration Board PICDEM-2 Low-Cost PIC16CXX Demonstration Board The PICDEM-2 is a simple demonstration board that supports the PIC16C62, PIC16C64, PIC16C65, PIC16C73 and PIC16C74 microcontrollers. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM-2 board, on a PRO MATE II programmer or PICSTART-Plus, and easily test firmware. The MPLAB-ICE emulator may also be used with the PICDEM-2 board to test firmware. Additional prototype area has been provided to the user for adding additional hardware and connecting it to the microcontroller socket(s). Some of the features include a RS-232 interface, push-button switches, a potentiometer for simulated analog input, a Serial EEPROM to demonstrate usage of the I2C bus and separate headers for connection to an LCD module and a keypad. MPLAB Integrated Development Environment Software The MPLAB IDE Software brings an ease of software development previously unseen in the 8-bit microcontroller market. MPLAB is a windows based application which contains: • A full featured editor • Three operating modes - editor - emulator - simulator • A project manager • Customizable tool bar and key mapping • A status bar with project information • Extensive on-line help MPLAB allows you to: • Edit your source files (either assembly or ‘C’) • One touch assemble (or compile) and download to PICmicro tools (automatically updates all project information) • Debug using: - source files - absolute listing file The ability to use MPLAB with Microchip’s simulator allows a consistent platform and the ability to easily switch from the low cost simulator to the full featured emulator with minimal retraining due to development tools. DS35008A-page 72 1998 Microchip Technology Inc. PIC16C62B/72A 12.11 Assembler (MPASM) The MPASM Universal Macro Assembler is a PChosted symbolic assembler. It supports all microcontroller series including the PIC12C5XX, PIC14000, PIC16C5X, PIC16CXXX, and PIC17CXX families. MPASM offers full featured Macro capabilities, conditional assembly, and several source and listing formats. It generates various object code formats to support Microchip's development tools as well as third party programmers. MPASM allows full symbolic debugging from MPLABICE, Microchip’s Universal Emulator System. MPASM has the following features to assist in developing software for specific use applications. • Provides translation of Assembler source code to object code for all Microchip microcontrollers. • Macro assembly capability. • Produces all the files (Object, Listing, Symbol, and special) required for symbolic debug with Microchip’s emulator systems. • Supports Hex (default), Decimal and Octal source and listing formats. MPASM provides a rich directive language to support programming of the PICmicro. Directives are helpful in making the development of your assemble source code shorter and more maintainable. 12.12 Software Simulator (MPLAB-SIM) The MPLAB-SIM Software Simulator allows code development in a PC host environment. It allows the user to simulate the PICmicro series microcontrollers on an instruction level. On any given instruction, the user may examine or modify any of the data areas or provide external stimulus to any of the pins. The input/ output radix can be set by the user and the execution can be performed in; single step, execute until break, or in a trace mode. MPLAB-SIM fully supports symbolic debugging using MPLAB-C17 and MPASM. The Software Simulator offers the low cost flexibility to develop and debug code outside of the laboratory environment making it an excellent multi-project software development tool. 1998 Microchip Technology Inc. 12.13 MPLAB-C17 Compiler The MPLAB-C17 Code Development System is a complete ANSI ‘C’ compiler and integrated development environment for Microchip’s PIC17CXXX family of microcontrollers. The compiler provides powerful integration capabilities and ease of use not found with other compilers. For easier source level debugging, the compiler provides symbol information that is compatible with the MPLAB IDE memory display. 12.14 Fuzzy Logic Development System (fuzzyTECH-MP) fuzzyTECH-MP fuzzy logic development tool is available in two versions - a low cost introductory version, MP Explorer, for designers to gain a comprehensive working knowledge of fuzzy logic system design; and a full-featured version, fuzzyTECH-MP, Edition for implementing more complex systems. Both versions include Microchip’s fuzzyLAB demonstration board for hands-on experience with fuzzy logic systems implementation. 12.15 SEEVAL Evaluation and Programming System The SEEVAL SEEPROM Designer’s Kit supports all Microchip 2-wire and 3-wire Serial EEPROMs. The kit includes everything necessary to read, write, erase or program special features of any Microchip SEEPROM product including Smart Serials and secure serials. The Total Endurance Disk is included to aid in tradeoff analysis and reliability calculations. The total kit can significantly reduce time-to-market and result in an optimized system. 12.16 KEELOQ Evaluation and Programming Tools KEELOQ evaluation and programming tools support Microchips HCS Secure Data Products. The HCS evaluation kit includes an LCD display to show changing codes, a decoder to decode transmissions, and a programming interface to program test transmitters. DS35008A-page 73 Emulator Products Software Tools DS35008A-page 74 Programmers ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü KEELOQ Transponder Kit ü ü ü ü ü ü ü HCS200 HCS300 HCS301 ü ü ü ü ü ü ü ü 24CXX 25CXX 93CXX KEELOQ® Evaluation Kit PICDEM-3 PICDEM-2 PICDEM-1 PICDEM-14A SIMICE Designers Kit SEEVAL KEELOQ Programmer PRO MATE II Universal Programmer Low-Cost Universal Dev. Kit PICSTARTPlus Total Endurance Software Model Explorer/Edition Fuzzy Logic Dev. Tool fuzzyTECH-MP MPLAB C17* Compiler ü ü ü MPLAB Integrated Development Environment ü ü ü ü PIC16C5X PIC16CXXX PIC16C6X PIC16C7XX PIC16C8X PIC16C9XX PIC17C4X PIC17C7XX ICEPIC Low-Cost In-Circuit Emulator MPLAB™-ICE PIC14000 TABLE 12-1: Demo Boards PIC12C5XX PIC16C62B/72A DEVELOPMENT TOOLS FROM MICROCHIP 1998 Microchip Technology Inc. PIC16C62B/72A 13.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings (†) Ambient temperature under bias............................................................................................................ .-55˚C to +125˚C Storage temperature .............................................................................................................................. -65˚C to +150˚C Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4).......................................... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +7.5V Voltage on MCLR with respect to VSS (Note 2).......................................................................................... 0V to +13.25V Voltage on RA4 with respect to Vss ............................................................................................................... 0V to +8.5V Total power dissipation (Note 1)................................................................................................................................1.0W Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD)......................................................................................................................±20 mA Output clamp current, IOK (VO < 0 or VO > VDD) ..............................................................................................................±20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk by PORTA and PORTB (combined) .................................................................................200 mA Maximum current sourced by PORTA and PORTB (combined)............................................................................200 mA Maximum current sunk by PORTC........................................................................................................................200 mA Maximum current sourced by PORTC ..................................................................................................................200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL) Note 2: Voltage spikes below VSS at the MCLR/VPP pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/VPP pin rather than pulling this pin directly to VSS. † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 13-1 OSC CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR MODES AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES) PIC16C62B-04 PIC16C72A-04 PIC16C62B-20 PIC16C72A-20 PIC16LC62B-04 PIC16LC72A-04 Windowed (JW) Devices RC VDD: 4.0V to 5.5V IDD: 5 mA max. at 5.5V IPD: 16 µA max. at 4V Freq: 4 MHz max. VDD: 4.5V to 5.5V IDD: 2.7 mA typ. at 5.5V IPD: 1.5 µA typ. at 4V Freq: 4 MHz max. VDD: 2.5V to 5.5V IDD: 3.8 mA max. at 3V IPD: 5 µA max. at 3V Freq: 4 MHz max. VDD: 2.5V to 5.5V IDD: 3.8 mA max. at 3V IPD: 5 µA max. at 3V Freq: 4 MHz max. XT VDD: 4.0V to 5.5V IDD: 5 mA max. at 5.5V IPD: 16 µA max. at 4V Freq: 4 MHz max. VDD: 4.5V to 5.5V IDD: 2.7 mA typ. at 5.5V IPD: 1.5 µA typ. at 4V Freq: 4 MHz max. VDD: 2.5V to 5.5V IDD: 3.8 mA max. at 3V IPD: 5 µA max. at 3V Freq: 4 MHz max. VDD: 2.5V to 5.5V IDD: 3.8 mA max. at 3V IPD: 5 µA max. at 3V Freq: 4 MHz max. HS VDD: 4.5V to 5.5V VDD: 4.5V to 5.5V IDD: 13.5 mA typ. at 5.5V IDD: 20 mA max. at 5.5V IPD: 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V Freq: 4 MHz max. Freq: 20 MHz max. VDD: 4.5V to 5.5V Not recommended for use in IDD: 20 mA max. at 5.5V HS mode IPD: 1.5 µA typ. at 4.5V Freq: 20 MHz max. LP VDD: 4.0V to 5.5V VDD: 2.5V to 5.5V VDD: 2.5V to 5.5V IDD: 52.5 µA typ. I DD: 48 µA max. at 32 kHz, I DD: 48 µA max. at 32 kHz, Not recommended for use in at 32 kHz, 4.0V 3.0V 3.0V LP mode IPD: 0.9 µA typ. at 4.0V IPD: 5 µA max. at 3.0V IPD: 5 µA max. at 3.0V Freq: 200 kHz max. Freq: 200 kHz max. Freq: 200 kHz max. The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recommended that the user select the device type that ensures the specifications required. 1998 Microchip Technology Inc. Preliminary DS35008A-page 75 PIC16C62B/72A 13.1 DC Characteristics: PIC16C62B/72A-04 (Commercial, Industrial, Extended) PIC16C62B/72A-20 (Commercial, Industrial, Extended) DC CHARACTERISTICS Param No. D001 D001A Sym VDD Characteristic Supply Voltage Standard Operating Conditions (unless otherwise stated) Operating temperature 0˚C ≤ TA ≤ +70˚C for commercial -40˚C ≤ TA ≤ +85˚C for industrial -40˚C ≤ TA ≤ +125˚C for extended Min Typ† Max Units 4.0 4.5 VBOR* - 5.5 5.5 5.5 V V V Conditions XT, RC and LP osc mode HS osc mode BOR enabled (Note 7) D002* VDR RAM Data Retention Voltage (Note 1) - 1.5 - V D003 VPOR VDD Start Voltage to ensure internal Power-on Reset signal - VSS - V D004* SVDD D004A* VDD Rise Rate to ensure internal Power-on Reset signal 0.05 TBD - - D005 VBOR Brown-out Reset voltage trip point 3.65 - 4.35 V D010 IDD Supply Current (Note 2, 5) - 2.7 5 mA XT, RC osc modes FOSC = 4 MHz, VDD = 5.5V (Note 4) - 10 20 mA HS osc mode FOSC = 20 MHz, VDD = 5.5V D021 D021B - 10.5 1.5 1.5 2.5 42 16 19 19 µA µA µA µA VDD = 4.0V, WDT enabled,-40°C to +85°C VDD = 4.0V, WDT disabled, 0°C to +70°C VDD = 4.0V, WDT disabled,-40°C to +85°C VDD = 4.0V, WDT disabled,-40°C to +125°C Module Differential Current (Note 6) D022* ∆IWDT Watchdog Timer D022A* ∆IBOR Brown-out Reset - 6.0 TBD 20 200 µA µA WDTE bit set, VDD = 4.0V BODEN bit set, VDD = 5.0V D013 IPD D020 * † Note1: 2: 3: 4: 5: 6: 7: Power-down Current (Note 3, 5) See section on Power-on Reset for details V/ms PWRT enabled (PWRTE bit clear) PWRT disabled (PWRTE bit set) See section on Power-on Reset for details BODEN bit set These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. This is the limit to which VDD can be lowered without losing RAM data. The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. For RC osc mode, current through Rext is not included. The current through the resistor can be estimated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm. Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from characterization and is for design guidance only. This is not tested. The ∆ current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. This is the voltage where the device enters the Brown-out Reset. When BOR is enabled, the device will operate correctly to this trip point. DS35008A-page 76 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 13.2 DC Characteristics: PIC16LC62B/72A-04 (Commercial, Industrial) DC CHARACTERISTICS Param No. Sym Characteristic D001 VDD Supply Voltage D002* VDR D003 VPOR RAM Data Retention Voltage (Note 1) VDD Start Voltage to ensure internal Power-on Reset signal VDD Rise Rate to ensure internal Power-on Reset signal Brown-out Reset voltage trip point Supply Current (Note 2, 5) D004* SVDD D004A* D005 VBOR D010 IDD D010A D020 D021 D021A IPD Power-down Current (Note 3, 5) Standard Operating Conditions (unless otherwise stated) Operating temperature 0˚C ≤ TA ≤ +70˚C for commercial -40˚C ≤ TA ≤ +85˚C for industrial Min Typ† Max Units Conditions 2.5 VBOR* - 1.5 5.5 5.5 - V V V LP, XT, RC osc modes (DC - 4 MHz) BOR enabled (Note 7) - VSS - V See section on Power-on Reset for details 0.05 TBD - - 3.65 - 4.35 - 2.0 3.8 mA XT, RC osc modes FOSC = 4 MHz, VDD = 3.0V (Note 4) - 22.5 48 µA - 7.5 0.9 0.9 30 5 5 µA µA µA LP osc mode FOSC = 32 kHz, VDD = 3.0V, WDT disabled VDD = 3.0V, WDT enabled, -40°C to +85°C VDD = 3.0V, WDT disabled, 0°C to +70°C VDD = 3.0V, WDT disabled, -40°C to +85°C V/ms PWRT enabled (PWRTE bit clear) PWRT disabled (PWRTE bit set) See section on Power-on Reset for details V BODEN bit set Module Differential Current (Note 6) 6.0 20 µA WDTE bit set, VDD = 4.0V D022* ∆IWDT Watchdog Timer TBD 200 µA BODEN bit set, VDD = 5.0V D022A* ∆IBOR Brown-out Reset * These parameters are characterized but not tested. † Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. Note1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through Rext is not included. The current through the resistor can be estimated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: This is the voltage where the device enters the Brown-out Reset. When BOR is enabled, the device will operate correctly to this trip point. 1998 Microchip Technology Inc. Preliminary DS35008A-page 77 PIC16C62B/72A 13.3 DC Characteristics: PIC16C62B/72A-04 (Commercial, Industrial, Extended) PIC16C62B/72A-20 (Commercial, Industrial, Extended) PIC16LC62B/72A-04 (Commercial, Industrial) DC CHARACTERISTICS Param No. Sym VIL D030 D030A D031 D032 D033 VIH D040 D040A D041 D042 D042A D043 D060 IIL D061 D063 D070 IPURB D080 VOL D083 Characteristic Input Low Voltage I/O ports with TTL buffer Standard Operating Conditions (unless otherwise stated) Operating temperature 0˚C ≤ TA ≤ +70˚C for commercial -40˚C ≤ TA ≤ +85˚C for industrial -40˚C ≤ TA ≤ +125˚C for extended Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2 Min Typ† Max Units Conditions VSS VSS VSS Vss Vss - 0.15VDD 0.8V 0.2VDD 0.2VDD 0.3VDD V V V V V For entire VDD range 4.5V ≤ VDD ≤ 5.5V - VDD VDD V V 4.5V ≤ VDD ≤ 5.5V For entire VDD range with Schmitt Trigger buffer 0.8VDD MCLR 0.8VDD OSC1 (XT, HS and LP modes) 0.7VDD OSC1 (in RC mode) 0.9VDD Input Leakage Current (Notes 2, 3) I/O ports - - VDD VDD VDD VDD V V V V For entire VDD range - ±1 µA MCLR, RA4/T0CKI OSC1 - - ±5 ±5 µA µA 50 250 400 µA Vss ≤ VPIN ≤ VDD, Pin at hi-impedance Vss ≤ VPIN ≤ VDD Vss ≤ VPIN ≤ VDD, XT, HS and LP osc modes VDD = 5V, VPIN = VSS - - 0.6 V - - 0.6 V - - 0.6 V - - 0.6 V with Schmitt Trigger buffer MCLR, OSC1 (in RC mode) OSC1 (in XT, HS and LP modes) Input High Voltage I/O ports with TTL buffer PORTB weak pull-up current Output Low Voltage I/O ports OSC2/CLKOUT (RC osc mode) 2.0 0.25VDD + 0.8V Note1 Note1 IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C IOL = 7.0 mA, VDD = 4.5V, -40°C to +125°C IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C IOL = 1.2 mA, VDD = 4.5V, -40°C to +125°C * † These parameters are characterized but not tested. Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note1: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with external clock in RC mode. 2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. DS35008A-page 78 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A DC CHARACTERISTICS Param No. D090 Sym VOH D092 Characteristic Output High Voltage I/O ports (Note 3) VDD-0.7 - - V VDD-0.7 - - V VDD-0.7 - - V VDD-0.7 - - V Open-Drain High Voltage Capacitive Loading Specs on Output Pins OSC2 pin - - 8.5 V - - 15 pF All I/O pins and OSC2 (in RC mode) - - 50 pF OSC2/CLKOUT (RC osc mode) D150* VOD D100 COSC2 D101 CIO Standard Operating Conditions (unless otherwise stated) Operating temperature 0˚C ≤ TA ≤ +70˚C for commercial -40˚C ≤ TA ≤ +85˚C for industrial -40˚C ≤ TA ≤ +125˚C for extended Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2 Min Typ† Max Units Conditions IOH = -3.0 mA, VDD = 4.5V, -40°C to +85°C IOH = -2.5 mA, VDD = 4.5V, -40°C to +125°C IOH = -1.3 mA, VDD = 4.5V, -40°C to +85°C IOH = -1.0 mA, VDD = 4.5V, -40°C to +125°C RA4 pin In XT, HS and LP modes when external clock is used to drive OSC1. 400 pF SCL, SDA in I2C mode * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note1: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with external clock in RC mode. 2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. D102 Cb 1998 Microchip Technology Inc. Preliminary DS35008A-page 79 PIC16C62B/72A 13.4 AC (Timing) Characteristics 13.4.1 TIMING PARAMETER SYMBOLOGY The timing parameter symbols have been created following one of the following formats: 1. TppS2ppS 3. TCC:ST (I2C specifications only) 2. TppS 4. Ts (I2C specifications only) T F Frequency Lowercase letters (pp) and their meanings: pp cc CCP1 ck CLKOUT cs CS di SDI do SDO dt Data in io I/O port mc MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (Hi-impedance) L Low I2C only AA BUF output access Bus free TCC:ST (I2C specifications only) CC HD Hold ST DAT DATA input hold STA START condition DS35008A-page 80 T Time osc rd rw sc ss t0 t1 wr OSC1 RD RD or WR SCK SS T0CKI T1CKI WR P R V Z Period Rise Valid Hi-impedance High Low High Low SU Setup STO STOP condition Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 13.4.2 TIMING CONDITIONS The temperature and voltages specified in Table 13-1 apply to all timing specifications unless otherwise noted. Figure 13-1 specifies the load conditions for the timing specifications. TABLE 13-1 TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC Standard Operating Conditions (unless otherwise stated) Operating temperature 0˚C ≤ TA ≤ +70˚C for commercial -40˚C ≤ TA ≤ +85˚C for industrial -40˚C ≤ TA ≤ +125˚C for extended Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2. LC parts operate for commercial/industrial temp’s only. AC CHARACTERISTICS FIGURE 13-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load condition 2 Load condition 1 VDD/2 RL CL Pin VSS CL Pin RL = 464Ω VSS CL = 50 pF 15 pF 1998 Microchip Technology Inc. Preliminary for all pins except OSC2/CLKOUT for OSC2 output DS35008A-page 81 PIC16C62B/72A 13.4.3 TIMING DIAGRAMS AND SPECIFICATIONS FIGURE 13-2: EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 OSC1 3 1 3 4 4 2 CLKOUT TABLE 13-2 Param No. 1A EXTERNAL CLOCK TIMING REQUIREMENTS Sym Fosc Characteristic Min Typ† Max External CLKIN Frequency (Note 1) DC DC DC DC DC 0.1 4 5 250 250 50 5 250 250 250 50 5 200 100 2.5 15 — — — — — — — — — — — — — — — — — — — — — — — — — — — 4 4 20 200 4 4 20 200 — — — — — 10,000 250 250 — DC — — — 25 50 15 Oscillator Frequency (Note 1) 1 Tosc External CLKIN Period (Note 1) Oscillator Period (Note 1) 2 3* TCY TosL, TosH Instruction Cycle Time (Note 1) External Clock in (OSC1) High or Low Time 4* TosR, TosF External Clock in (OSC1) Rise or Fall Time * † Note1: Units Conditions MHz MHz MHz kHz MHz MHz MHz kHz ns ns ns µs ns ns ns ns µs ns ns µs ns ns ns ns RC and XT osc modes HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode LP osc mode RC and XT osc modes HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode (-04) HS osc mode (-20) LP osc mode TCY = 4/FOSC XT oscillator LP oscillator HS oscillator XT oscillator LP oscillator HS oscillator These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. DS35008A-page 82 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A FIGURE 13-3: CLKOUT AND I/O TIMING Q1 Q4 Q2 Q3 OSC1 11 10 CLKOUT 13 19 14 12 18 16 I/O Pin (input) 15 17 I/O Pin (output) new value old value 20, 21 Note: Refer to Figure 13-1 for load conditions. TABLE 13-3 Param No. CLKOUT AND I/O TIMING REQUIREMENTS Sym Characteristic 10* TosH2ckL OSC1↑ to CLKOUT↓ 11* TosH2ckH OSC1↑ to CLKOUT↑ — 75 200 ns Note 1 12* TckR CLKOUT rise time — 35 100 ns Note 1 13* TckF CLKOUT fall time — 35 100 ns Note 1 14* TckL2ioV CLKOUT ↓ to Port out valid — — 0.5TCY + 20 ns Note 1 15* TioV2ckH Port in valid before CLKOUT ↑ Tosc + 200 — — ns Note 1 16* TckH2ioI Port in hold after CLKOUT ↑ 0 — — ns Note 1 17* TosH2ioV OSC1↑ (Q1 cycle) to Port out valid — 50 150 ns 18* TosH2ioI OSC1↑ (Q2 cycle) to Port input invalid (I/O in hold time) Standard 100 — — ns Extended (LC) 200 — — ns 18A* Min Typ† Max — 75 200 Units Conditions ns 19* TioV2osH Port input valid to OSC1↑ (I/O in setup time) 0 — — ns 20* TioR Port output rise time Standard — 10 40 ns Extended (LC) — — 80 ns TioF Port output fall time Standard — 10 40 ns — — 80 ns 22††* Tinp INT pin high or low time TCY — — ns 23††* Trbp RB7:RB4 change INT high or low time TCY — — ns 20A* 21* 21A* Extended (LC) Note 1 * † These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. †† These parameters are asynchronous events not related to any internal clock edge. Note1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC. 1998 Microchip Technology Inc. Preliminary DS35008A-page 83 PIC16C62B/72A FIGURE 13-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal RESET Watchdog Timer RESET 31 34 34 I/O Pins Note: Refer to Figure 13-1 for load conditions. FIGURE 13-5: BROWN-OUT RESET TIMING BVDD VDD TABLE 13-4 35 RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER, AND BROWN-OUT RESET REQUIREMENTS Parameter No. Sym Characteristic Min Typ† Max Units 30 TmcL 31* MCLR Pulse Width (low) 2 — — µs VDD = 5V, -40˚C to +125˚C Twdt Watchdog Timer Time-out Period (No Prescaler) 7 18 33 ms VDD = 5V, -40˚C to +125˚C 32 Tost Oscillation Start-up Timer Period — 1024 TOSC — — TOSC = OSC1 period 33* Tpwrt Power-up Timer Period 28 72 132 ms VDD = 5V, -40˚C to +125˚C 34 TIOZ I/O Hi-impedance from MCLR Low or WDT reset — — 2.1 µs 35 TBOR Brown-out Reset Pulse Width 100 — — µs * † Conditions VDD ≤ BVDD (D005) These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. DS35008A-page 84 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A FIGURE 13-6: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS T0CKI 41 40 42 T1OSO/T1CKI 46 45 47 48 TMR0 or TMR1 Note: Refer to Figure 13-1 for load conditions. TABLE 13-5 TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS Param No. Sym Characteristic 40* Tt0H T0CKI High Pulse Width No Prescaler T0CKI Low Pulse Width With Prescaler No Prescaler With Prescaler 41* 42* 45* 46* 47* 48 * † Tt0L Min Typ† Max 0.5TCY + 20 — — ns 10 — — — — — — — — — — ns ns ns ns ns — — — — — — ns ns ns — — — — — — — — — — ns ns ns ns ns — — — — — — ns ns ns 0.5TCY + 20 10 Tt0P T0CKI Period TCY + 40 No Prescaler With Prescaler Greater of: 20 or TCY + 40 N Tt1H T1CKI High Time Synchronous, Prescaler = 1 0.5TCY + 20 Synchronous, Standard 15 Prescaler = 25 Extended (LC) 2,4,8 Asynchronous Standard 30 50 Extended (LC) Tt1L T1CKI Low Time Synchronous, Prescaler = 1 0.5TCY + 20 Synchronous, Standard 15 Prescaler = 25 Extended (LC) 2,4,8 Asynchronous Standard 30 50 Extended (LC) Greater of: Tt1P T1CKI input period Synchronous Standard 30 OR TCY + 40 N Extended (LC) Greater of: 50 OR TCY + 40 N Asynchronous Standard 60 100 Extended (LC) Ft1 Timer1 oscillator input frequency range DC (oscillator enabled by setting bit T1OSCEN) TCKEZtmr1 Delay from external clock edge to timer increment 2Tosc Units Conditions Must also meet parameter 42 Must also meet parameter 42 N = prescale value (2, 4,..., 256) Must also meet parameter 47 Must also meet parameter 47 N = prescale value (1, 2, 4, 8) N = prescale value (1, 2, 4, 8) — — — — — 200 ns ns kHz — 7Tosc — These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. 1998 Microchip Technology Inc. Preliminary DS35008A-page 85 PIC16C62B/72A FIGURE 13-7: CAPTURE/COMPARE/PWM TIMINGS CCP1 (Capture Mode) 50 51 52 CCP1 (Compare or PWM Mode) 53 54 Note: Refer to Figure 13-1 for load conditions. TABLE 13-6 CAPTURE/COMPARE/PWM REQUIREMENTS Param No. Sym Characteristic Min 50* TccL CCP1 input low time No Prescaler TccH CCP1 input high time No Prescaler With Prescaler Standard Extended (LC) 51* With Prescaler 52* TccP CCP1 input period 53* TccR CCP1 output rise time 54* * † TccF CCP1 output fall time Typ† Max Units Conditions 0.5TCY + 20 — — ns 10 — — ns 20 — — ns 0.5TCY + 20 — — ns Standard 10 — — ns Extended (LC) 20 — — ns 3TCY + 40 N — — ns Standard — 10 25 ns Extended (LC) — 25 45 ns Standard — 10 25 ns Extended (LC) — 25 45 ns N = prescale value (1,4, or 16) These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. DS35008A-page 86 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A FIGURE 13-8: EXAMPLE SPI MASTER MODE TIMING (CKE = 0) SS 70 SCK (CKP = 0) 71 72 78 79 79 78 SCK (CKP = 1) 80 BIT6 - - - - - -1 MSb SDO LSb 75, 76 SDI MSb IN BIT6 - - - -1 LSb IN 74 73 Refer to Figure 13-1 for load conditions. TABLE 13-7 Param. No. 70 71 EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 0) Symbol Characteristic Min TssL2scH, SS↓ to SCK↓ or SCK↑ input TssL2scL TscH SCK input high time Continuous (slave mode) Single Byte Typ† Max Units TCY — — ns 1.25TCY + 30 40 1.25TCY + 30 40 100 — — — — — — — — — — ns ns ns ns ns Conditions Note 1 Continuous 72A Single Byte Note 1 73 TdiV2scH, Setup time of SDI data input to SCK edge TdiV2scL 73A TB2B Last clock edge of Byte1 to the 1st clock 1.5TCY + 40 — — ns Note 1 edge of Byte2 74 TscH2diL, Hold time of SDI data input to SCK edge 100 — — ns TscL2diL 75 TdoR SDO data output rise time Standard — 10 25 ns Extended (LC) — 20 45 ns 76 TdoF SDO data output fall time — 10 25 ns 78 TscR SCK output rise time Standard — 10 25 ns (master mode) Extended (LC) — 20 45 ns 79 TscF SCK output fall time (master mode) — 10 25 ns 80 TscH2doV, SDO data output valid Standard — — 50 ns TscL2doV after SCK edge Extended (LC) — — 100 ns † Data in “Typ” column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. Note1: Specification 73A is only required if specifications 71A and 72A are used. 71A 72 TscL SCK input low time (slave mode) 1998 Microchip Technology Inc. Preliminary DS35008A-page 87 PIC16C62B/72A FIGURE 13-9: EXAMPLE SPI MASTER MODE TIMING (CKE = 1) SS 81 SCK (CKP = 0) 71 72 79 73 SCK (CKP = 1) 80 78 LSb BIT6 - - - - - -1 MSb SDO 75, 76 SDI MSb IN BIT6 - - - -1 LSb IN 74 Refer to Figure 13-1 for load conditions. TABLE 13-8 Param. No. 71 EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 1) Symbol TscH 71A 72 TscL 72A 73 73A 74 75 TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR Characteristic Min SCK input high time (slave mode) Continuous Single Byte SCK input low time Continuous (slave mode) Single Byte Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time Typ† Max Units 1.25TCY + 30 40 1.25TCY + 30 40 100 — — — — — — — — — — ns ns ns ns ns 1.5TCY + 40 — — ns 100 — — ns — 10 20 10 10 20 10 — — — 25 45 25 25 45 25 50 100 — ns ns ns ns ns ns ns ns ns Standard Extended (LC) Note 1 Note 1 Note 1 SDO data output fall time — SCK output rise time Standard — (master mode) Extended (LC) 79 TscF SCK output fall time (master mode) — 80 TscH2doV, SDO data output valid Standard — TscL2doV after SCK edge Extended (LC) 81 TdoV2scH, SDO data output setup to SCK edge TCY TdoV2scL † Data in “Typ” column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. Note1: Specification 73A is only required if specifications 71A and 72A are used. 76 78 TdoF TscR Conditions DS35008A-page 88 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A FIGURE 13-10: EXAMPLE SPI SLAVE MODE TIMING (CKE = 0) SS 70 SCK (CKP = 0) 83 71 72 78 79 79 78 SCK (CKP = 1) 80 MSb SDO LSb BIT6 - - - - - -1 77 75, 76 SDI MSb IN BIT6 - - - -1 LSb IN 74 73 Refer to Figure 13-1 for load conditions. TABLE 13-9 Param. No. 70 71 71A 72 72A 73 73A 74 75 76 77 78 79 80 83 EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING (CKE = 0) Symbol Characteristic Min TssL2scH, SS↓ to SCK↓ or SCK↑ input TssL2scL TscH SCK input high time Continuous (slave mode) Single Byte TscL SCK input low time (slave mode) Continuous Single Byte TdiV2scH, Setup time of SDI data input to SCK edge TdiV2scL TB2B Last clock edge of Byte1 to the 1st clock edge of Byte2 TscH2diL, Hold time of SDI data input to SCK edge TscL2diL TdoR SDO data output rise time Standard Extended (LC) TdoF SDO data output fall time TssH2doZ SS↑ to SDO output hi-impedance TscR SCK output rise time Standard (master mode) Extended (LC) TscF SCK output fall time (master mode) TscH2doV, SDO data output valid Standard TscL2doV after SCK edge Extended (LC) TscH2ssH, SS ↑ after SCK edge TscL2ssH Typ† Max Units TCY — — ns 1.25TCY + 30 40 1.25TCY + 30 40 100 — — — — — — — — — — ns ns ns ns ns 1.5TCY + 40 — — ns 100 — — ns — 10 20 10 — 10 20 10 — — — 25 45 25 50 25 45 25 50 100 — ns ns ns ns ns ns ns ns ns ns — 10 — — — 1.5TCY + 40 Conditions Note 1 Note 1 Note 1 † Data in “Typ” column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. Note1: Specification 73A is only required if specifications 71A and 72A are used. 1998 Microchip Technology Inc. Preliminary DS35008A-page 89 PIC16C62B/72A FIGURE 13-11: EXAMPLE SPI SLAVE MODE TIMING (CKE = 1) 82 SS 70 SCK (CKP = 0) 83 71 72 SCK (CKP = 1) 80 MSb SDO BIT6 - - - - - -1 LSb 75, 76 SDI MSb IN 77 BIT6 - - - -1 LSb IN 74 Refer to Figure 13-1 for load conditions. TABLE 13-10 Param. No. 70 71 EXAMPLE SPI SLAVE MODE REQUIREMENTS (CKE = 1) Symbol Characteristic Min SS↓ to SCK↓ or SCK↑ input TCY — — ns 1.25TCY + 30 40 1.25TCY + 30 40 1.5TCY + 40 — — — — — — — — — — ns ns ns ns ns 100 — — ns Standard Extended (LC) — SDO data output fall time SS↑ to SDO output hi-impedance SCK output rise time Standard (master mode) Extended (LC) TscF SCK output fall time (master mode) TscH2doV, SDO data output valid Standard TscL2doV after SCK edge Extended (LC) TssL2doV SDO data output valid Standard after SS↓ edge Extended (LC) TscH2ssH, SS ↑ after SCK edge TscL2ssH — 10 — — — — — — — 10 20 10 — 10 20 10 — — — — — 25 45 25 50 25 45 25 50 100 50 100 — ns ns ns ns ns ns ns ns ns ns ns ns TssL2scH, TssL2scL TscH 71A 72 TscL 72A 73A 74 75 76 77 78 79 80 82 83 TB2B TscH2diL, TscL2diL TdoR SCK input high time (slave mode) Continuous Single Byte SCK input low time Continuous (slave mode) Single Byte Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time TdoF TssH2doZ TscR 1.5TCY + 40 Typ† Max Units Conditions Note 1 Note 1 Note 1 † Data in “Typ” column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not tested. Note1: Specification 73A is only required if specifications 71A and 72A are used. DS35008A-page 90 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A FIGURE 13-12: I2C BUS START/STOP BITS TIMING SCL 91 93 90 92 SDA STOP Condition START Condition Note: Refer to Figure 13-1 for load conditions. TABLE 13-11 I2C BUS START/STOP BITS REQUIREMENTS Parameter No. Sym 90* TSU:STA 91* 92* 93 * Characteristic Min START condition 100 kHz mode Setup time 400 kHz mode THD:STA START condition 100 kHz mode Hold time 400 kHz mode TSU:STO STOP condition 100 kHz mode Setup time 400 kHz mode THD:STO STOP condition 100 kHz mode Hold time 400 kHz mode These parameters are characterized but not tested. 1998 Microchip Technology Inc. 4700 600 4000 600 4700 600 4000 600 Preliminary Typ Max — — — — — — — — — — — — — — — — Units Conditions ns Only relevant for repeated START condition ns After this period the first clock pulse is generated ns ns DS35008A-page 91 PIC16C62B/72A FIGURE 13-13: I2C BUS DATA TIMING 103 102 100 101 SCL 90 106 107 91 92 SDA In 110 109 109 SDA Out Note: Refer to Figure 13-1 for load conditions. I2C BUS DATA REQUIREMENTS TABLE 13-12 Parameter No. Sym Characteristic 100* THIGH Clock high time 101* 102* 103* TLOW TR TF Min Max Units Conditions 100 kHz mode 4.0 — µs 400 kHz mode 0.6 — µs Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz SSP Module 100 kHz mode 1.5TCY 4.7 — — µs 400 kHz mode 1.3 — µs SSP Module 100 kHz mode 400 kHz mode 1.5TCY — 20 + 0.1Cb — 1000 300 ns ns SDA and SCL fall time 100 kHz mode 400 kHz mode — 20 + 0.1Cb 300 300 ns ns 4.7 0.6 4.0 0.6 0 0 250 100 4.7 0.6 — — 4.7 1.3 — — — — — 0.9 — — — — 3500 — — — µs µs µs µs ns µs ns ns µs µs ns ns µs µs Clock low time SDA and SCL rise time 90* TSU:STA 91* THD:STA 106* THD:DAT START condition setup time START condition hold time Data input hold time 107* TSU:DAT Data input setup time 92* TSU:STO 109* TAA 110* TBUF STOP condition setup time Output valid from clock Bus free time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz Cb is specified to be from 10-400 pF Cb is specified to be from 10-400 pF Only relevant for repeated START condition After this period the first clock pulse is generated Note 2 Note 1 Time the bus must be free before a new transmission can start Cb Bus capacitive loading — 400 pF These parameters are characterized but not tested. As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 2: A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the requirement Tsu:DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the SCL line is released. * Note 1: DS35008A-page 92 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A TABLE 13-13 A/D CONVERTER CHARACTERISTICS: PIC16C72A-04 (COMMERCIAL, INDUSTRIAL, EXTENDED) PIC16C72A-20 (COMMERCIAL, INDUSTRIAL, EXTENDED) PIC16LC72A-04 (COMMERCIAL, INDUSTRIAL) Param Sym Characteristic No. A01 NR A02 Resolution EABS Total Absolute error Typ† Max Units Conditions — — 8-bits bit — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF A03 EIL A04 EDL Differential linearity error — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF A05 EFS Full scale error — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF A06 EOFF Offset error — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF — guaranteed (Note 3) — — V A10 — Integral linearity error Min Monotonicity A20 VREF Reference voltage A25 VAIN Analog input voltage A30 ZAIN Recommended impedance of analog voltage source A40 IAD A/D conversion current (VDD) 2.5V — VDD + 0.3 VSS - 0.3 — VREF + 0.3 V — — 10.0 kΩ Standard — 180 — µA Extended (LC) — 90 — µA 10 — 1000 µA During VAIN acquisition. Based on differential of VHOLD to VAIN to charge CHOLD, see Section 9.1. — — 10 µA During A/D Conversion cycle IREF VREF input current (Note 2) A50 VSS ≤ VAIN ≤ VREF Average current consumption when A/D is on. (Note 1) * † These parameters are characterized but not tested. Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current spec includes any such leakage from the A/D module. 2: VREF current is from RA3 pin or VDD pin, whichever is selected as reference input. 3: The A/D conversion result never decreases with an increase in the Input Voltage, and has no missing codes. 1998 Microchip Technology Inc. Preliminary DS35008A-page 93 PIC16C62B/72A FIGURE 13-14: A/D CONVERSION TIMING BSF ADCON0, GO 134 1 Tcy (TOSC/2) (1) 131 Q4 130 132 A/D CLK 7 A/D DATA 6 5 4 3 2 1 NEW_DATA OLD_DATA ADRES 0 ADIF GO DONE SAMPLING STOPPED SAMPLE Note1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. TABLE 13-14 Param No. 130 A/D CONVERSION REQUIREMENTS Sym Characteristic TAD A/D clock period Min Typ† Max Units Conditions Standard 1.6 — — µs Extended (LC) 2.0 — — µs TOSC based, VREF ≥ 3.0V TOSC based, VREF full range Standard 2.0 4.0 6.0 µs A/D RC Mode A/D RC Mode Extended (LC) 3.0 6.0 9.0 µs 131 TCNV Conversion time (not including S/H time) (Note 1) 11 — 11 TAD 132 TACQ Acquisition time Note 2 20 — µs 5* — — µs The minimum time is the amplifier settling time. This may be used if the "new" input voltage has not changed by more than 1 LSb (i.e., 20.0 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). — TOSC/2 § — — If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 1.5 § — — TAD 134 TGO Q4 to A/D clock start TSWC Switching from convert → sample time 135 * † These parameters are characterized but not tested. Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. § This specification ensured by design. Note 1: ADRES register may be read on the following TCY cycle. 2: See Section 9.1 for min conditions. DS35008A-page 94 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 14.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES The graphs and tables provided in this section are for design guidance and are not tested. In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices are guaranteed to operate properly only within the specified range. The data presented in this section is a statistical summary of data collected on units from different lots over a period of time and matrix samples. 'Typical' represents the mean of the distribution at 25°C. 'Max' or 'min' represents (mean + 3σ) or (mean - 3σ) respectively, where σ is standard deviation, over the whole temperature range. Graphs and Tables not available at this time. Data is not available at this time but you may reference the PIC16C72 Series Data Sheet (DS39016) DC and AC characteristic section which contains data similar to what is expected. 1998 Microchip Technology Inc. Preliminary DS35008A-page 95 PIC16C62B/72A NOTES: DS35008A-page 96 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 15.0 PACKAGING INFORMATION 15.1 Package Marking Information 28-Lead PDIP (Skinny DIP) Example MMMMMMMMMMMM XXXXXXXXXXXXXXX AABBCDE 28-Lead CERDIP Windowed PIC16C72A-04/SP 9817HAT Example XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX AABBCDE PIC16C72A/JW 9817CAT Example 28-Lead SOIC MMMMMMMMMMMMMMMM XXXXXXXXXXXXXXXXXXXX AABBCDE 28-Lead SSOP PIC16C62B-20/SO 9810/SAA Example XXXXXXXXXXXX XXXXXXXXXXXX PIC16C62B 20I/SS025 AABBCDE 9817SBP Legend: MM...M XX...X AA BB C D E Note: * Microchip part number information Customer specific information* Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Facility code of the plant at which wafer is manufactured O = Outside Vendor C = 5” Line S = 6” Line H = 8” Line Mask revision number Assembly code of the plant or country of origin in which part was assembled In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. Standard OTP marking consists of Microchip part number, year code, week code, facility code, mask rev#, and assembly code. For OTP marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. 1998 Microchip Technology Inc. Preliminary DS35008A-page 97 PIC16C62B/72A 15.2 K04-070 28-Lead Skinny Plastic Dual In-line (SP) – 300 mil E D 2 n α 1 E1 A1 A R β L c B1 A2 eB Units Dimension Limits PCB Row Spacing Number of Pins Pitch Lower Lead Width Upper Lead Width Shoulder Radius Lead Thickness Top to Seating Plane Top of Lead to Seating Plane Base to Seating Plane Tip to Seating Plane Package Length Molded Package Width Radius to Radius Width Overall Row Spacing Mold Draft Angle Top Mold Draft Angle Bottom p B INCHES* NOM 0.300 28 0.100 0.016 0.019 0.040 0.053 0.000 0.005 0.008 0.010 0.140 0.150 0.070 0.090 0.015 0.020 0.125 0.130 1.345 1.365 0.280 0.288 0.270 0.283 0.320 0.350 5 10 5 10 MIN n p B B1† R c A A1 A2 L D‡ E‡ E1 eB α β MAX 0.022 0.065 0.010 0.012 0.160 0.110 0.025 0.135 1.385 0.295 0.295 0.380 15 15 MILLIMETERS MAX NOM 7.62 28 2.54 0.56 0.41 0.48 1.65 1.02 1.33 0.00 0.25 0.13 0.20 0.30 0.25 3.56 4.06 3.81 1.78 2.79 2.29 0.38 0.64 0.51 3.18 3.43 3.30 35.18 34.16 34.67 7.11 7.30 7.49 6.86 7.18 7.49 8.13 9.65 8.89 5 10 15 5 10 15 MIN * Controlling Parameter. † Dimension “B1” does not include dam-bar protrusions. Dam-bar protrusions shall not exceed 0.003” (0.076 mm) per side or 0.006” (0.152 mm) more than dimension “B1.” ‡ Dimensions “D” and “E” do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010” (0.254 mm) per side or 0.020” (0.508 mm) more than dimensions “D” or “E.” DS35008A-page 98 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 15.3 K04-080 28-Lead Ceramic Dual In-line with Window (JW) – 300 mil E D W2 2 n 1 W1 E1 A R A1 L c eB Units Dimension Limits PCB Row Spacing Number of Pins Pitch Lower Lead Width Upper Lead Width Shoulder Radius Lead Thickness Top to Seating Plane Top of Lead to Seating Plane Base to Seating Plane Tip to Seating Plane Package Length Package Width Radius to Radius Width Overall Row Spacing Window Width Window Length B1 B A2 MIN n p B B1 R c A A1 A2 L D E E1 eB W1 W2 0.098 0.016 0.050 0.010 0.008 0.170 0.107 0.015 0.135 1.430 0.285 0.255 0.345 0.130 0.290 INCHES* NOM 0.300 28 0.100 0.019 0.058 0.013 0.010 0.183 0.125 0.023 0.140 1.458 0.290 0.270 0.385 0.140 0.300 p MAX 0.102 0.021 0.065 0.015 0.012 0.195 0.143 0.030 0.145 1.485 0.295 0.285 0.425 0.150 0.310 MILLIMETERS MIN NOM MAX 7.62 28 2.49 2.54 2.59 0.41 0.47 0.53 1.27 1.46 1.65 0.25 0.32 0.38 0.20 0.25 0.30 4.32 4.64 4.95 2.72 3.63 3.18 0.76 0.00 0.57 3.68 3.43 3.56 37.72 36.32 37.02 7.49 7.24 7.37 7.24 6.48 6.86 10.80 8.76 9.78 0.15 0.13 0.14 0.31 0.29 0.3 * Controlling Parameter. 1998 Microchip Technology Inc. Preliminary DS35008A-page 99 PIC16C62B/72A 15.4 K04-052 28-Lead Plastic Small Outline (SO) – Wide, 300 mil E1 E p D B 2 1 n X α 45 ° L R2 c A β Units Dimension Limits Pitch Number of Pins Overall Pack. Height Shoulder Height Standoff Molded Package Length Molded Package Width Outside Dimension Chamfer Distance Shoulder Radius Gull Wing Radius Foot Length Foot Angle Radius Centerline Lead Thickness Lower Lead Width Mold Draft Angle Top Mold Draft Angle Bottom A1 φ R1 L1 A2 INCHES* NOM 0.050 28 0.099 0.093 0.058 0.048 0.008 0.004 0.706 0.700 0.296 0.292 0.407 0.394 0.020 0.010 0.005 0.005 0.005 0.005 0.016 0.011 0 4 0.015 0.010 0.011 0.009 0.014 0.017 0 12 0 12 MIN p n A A1 A2 D‡ E‡ E1 X R1 R2 L φ L1 c B† α β MAX 0.104 0.068 0.011 0.712 0.299 0.419 0.029 0.010 0.010 0.021 8 0.020 0.012 0.019 15 15 MILLIMETERS NOM MAX 1.27 28 2.36 2.50 2.64 1.22 1.47 1.73 0.10 0.19 0.28 17.78 17.93 18.08 7.51 7.59 7.42 10.01 10.33 10.64 0.50 0.74 0.25 0.13 0.25 0.13 0.13 0.25 0.13 0.41 0.53 0.28 8 4 0 0.38 0.51 0.25 0.27 0.30 0.23 0.36 0.42 0.48 0 12 15 0 12 15 MIN * Controlling Parameter. † Dimension “B” does not include dam-bar protrusions. Dam-bar protrusions shall not exceed 0.003” (0.076 mm) per side or 0.006” (0.152 mm) more than dimension “B.” ‡ Dimensions “D” and “E” do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010” (0.254 mm) per side or 0.020” (0.508 mm) more than dimensions “D” or “E.” DS35008A-page 100 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A 15.5 K04-073 28-Lead Plastic Shrink Small Outline (SS) – 5.30 mm E1 E p D B 2 1 n α L A R2 c A1 R1 A2 L1 β Units Dimension Limits Pitch Number of Pins Overall Pack. Height Shoulder Height Standoff Molded Package Length Molded Package Width Outside Dimension Shoulder Radius Gull Wing Radius Foot Length Foot Angle Radius Centerline Lead Thickness Lower Lead Width Mold Draft Angle Top Mold Draft Angle Bottom φ INCHES NOM 0.026 28 0.073 0.068 0.036 0.026 0.005 0.002 0.402 0.396 0.208 0.205 0.306 0.301 0.005 0.005 0.005 0.005 0.020 0.015 0 4 0.005 0.000 0.007 0.005 0.010 0.012 0 5 0 5 MIN p n A A1 A2 D‡ E‡ E1 R1 R2 L φ L1 c B† α β MAX 0.078 0.046 0.008 0.407 0.212 0.311 0.010 0.010 0.025 8 0.010 0.009 0.015 10 10 MILLIMETERS* NOM MAX 0.65 28 1.99 1.73 1.86 1.17 0.66 0.91 0.21 0.05 0.13 10.33 10.07 10.20 5.38 5.20 5.29 7.90 7.65 7.78 0.25 0.13 0.13 0.25 0.13 0.13 0.64 0.38 0.51 0 4 8 0.25 0.00 0.13 0.22 0.13 0.18 0.38 0.25 0.32 10 0 5 10 0 5 MIN * Controlling Parameter. † Dimension “B” does not include dam-bar protrusions. Dam-bar protrusions shall not exceed 0.003” (0.076 mm) per side or 0.006” (0.152 mm) more than dimension “B.” ‡ Dimensions “D” and “E” do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010” (0.254 mm) per side or 0.020” (0.508 mm) more than dimensions “D” or “E.” 1998 Microchip Technology Inc. Preliminary DS35008A-page 101 PIC16C62B/72A NOTES: DS35008A-page 102 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A APPENDIX A: REVISION HISTORY Version Date Revision Description A 7/98 This is a new data sheet. However, the devices described in this data sheet are the upgrades to the devices found in the PIC16C6X Data Sheet, DS30234, and the PIC16C7X Data Sheet, DS30390. APPENDIX B: CONVERSION CONSIDERATIONS Considerations for converting from previous versions of devices to the ones listed in this data sheet are listed in Table B-1. TABLE B-1: CONVERSION CONSIDERATIONS Difference PIC16C62A/72 PIC16C62B/72A Voltage Range 2.5V - 6.0V 2.5V - 5.5V SSP module Basic SSP (2 mode SPI) SSP (4 mode SPI) SSP module Can only transmit one word in SPI mode of enhanced SSP. N/A CCP module CCP does not reset TMR1 when in special event trigger mode. N/A Timer1 module Writing to TMR1L register can cause overflow in TMR1H register. N/A 1998 Microchip Technology Inc. Preliminary DS35008A-page 103 PIC16C62B/72A APPENDIX C: MIGRATION FROM BASE-LINE TO MID-RANGE DEVICES This section discusses how to migrate from a baseline device (i.e., PIC16C5X) to a mid-range device (i.e., PIC16CXXX). The following are the list of modifications over the PIC16C5X microcontroller family: 1. Instruction word length is increased to 14-bits. This allows larger page sizes both in program memory (2K now as opposed to 512 before) and register file (128 bytes now versus 32 bytes before). 2. A PC high latch register (PCLATH) is added to handle program memory paging. Bits PA2, PA1, PA0 are removed from STATUS register. 3. Data memory paging is redefined slightly. STATUS register is modified. 4. Four new instructions have been added: RETURN, RETFIE, ADDLW, and SUBLW. Two instructions TRIS and OPTION are being phased out although they are kept for compatibility with PIC16C5X. 5. OPTION_REG and TRIS registers are made addressable. 6. Interrupt capability is added. Interrupt vector is at 0004h. 7. Stack size is increased to 8 deep. 8. Reset vector is changed to 0000h. 9. Reset of all registers is revisited. Five different reset (and wake-up) types are recognized. Registers are reset differently. 10. Wake up from SLEEP through interrupt is added. DS35008A-page 104 11. Two separate timers, Oscillator Start-up Timer (OST) and Power-up Timer (PWRT) are included for more reliable power-up. These timers are invoked selectively to avoid unnecessary delays on power-up and wake-up. 12. PORTB has weak pull-ups and interrupt on change feature. 13. T0CKI pin is also a port pin (RA4) now. 14. FSR is made a full eight bit register. 15. “In-circuit serial programming” is made possible. The user can program PIC16CXX devices using only five pins: VDD, VSS, MCLR/VPP, RB6 (clock) and RB7 (data in/out). 16. PCON status register is added with a Power-on Reset status bit (POR). 17. Code protection scheme is enhanced such that portions of the program memory can be protected, while the remainder is unprotected. 18. Brown-out protection circuitry has been added. Controlled by configuration word bit BODEN. Brown-out reset ensures the device is placed in a reset condition if VDD dips below a fixed setpoint. To convert code written for PIC16C5X to PIC16CXXX, the user should take the following steps: 1. 2. 3. 4. 5. Preliminary Remove any program memory page select operations (PA2, PA1, PA0 bits) for CALL, GOTO. Revisit any computed jump operations (write to PC or add to PC, etc.) to make sure page bits are set properly under the new scheme. Eliminate any data memory page switching. Redefine data variables to reallocate them. Verify all writes to STATUS, OPTION, and FSR registers since these have changed. Change reset vector to 0000h. 1998 Microchip Technology Inc. PIC16C62B/72A INDEX A A/D ..................................................................................... 49 A/D Converter Enable (ADIE Bit) ............................... 14 A/D Converter Flag (ADIF Bit) ............................. 15, 51 A/D Converter Interrupt, Configuring ......................... 51 ADCON0 Register .................................................. 9, 49 ADCON1 Register .......................................... 10, 49, 50 ADRES Register .............................................. 9, 49, 51 Analog Port Pins .......................................................... 6 Analog Port Pins, Configuring .................................... 53 Block Diagram ............................................................ 51 Block Diagram, Analog Input Model ........................... 52 Channel Select (CHS2:CHS0 Bits) ............................ 49 Clock Select (ADCS1:ADCS0 Bits) ............................ 49 Configuring the Module .............................................. 51 Conversion Clock (TAD) ............................................. 53 Conversion Status (GO/DONE Bit) ...................... 49, 51 Conversions ............................................................... 54 Converter Characteristics .......................................... 93 Module On/Off (ADON Bit) ......................................... 49 Port Configuration Control (PCFG2:PCFG0 Bits) ...... 50 Sampling Requirements ............................................. 52 Special Event Trigger (CCP) ................................ 35, 54 Timing Diagram .......................................................... 94 Absolute Maximum Ratings ............................................... 75 ADCON0 Register .......................................................... 9, 49 ADCS1:ADCS0 Bits ................................................... 49 ADON Bit ................................................................... 49 CHS2:CHS0 Bits ........................................................ 49 GO/DONE Bit ....................................................... 49, 51 ADCON1 Register .................................................. 10, 49, 50 PCFG2:PCFG0 Bits ................................................... 50 ADRES Register ...................................................... 9, 49, 51 Analog Port Pins. See A/D Analog-to-Digital Converter. See A/D Architecture PIC16C62B/PIC16C72A Block Diagram ...................... 5 Assembler MPASM Assembler .................................................... 73 PWM Mode. See PWM RC2/CCP1 Pin ..............................................................6 Timer Resources ....................................................... 33 Timing Diagram ......................................................... 86 CCP1CON Register ........................................................... 33 CCP1M3:CCP1M0 Bits ............................................. 33 CCP1X:CCP1Y Bits ................................................... 33 Code Protection ........................................................... 55, 68 CP1:CP0 Bits ............................................................. 55 Compare (CCP Module) .................................................... 35 Block Diagram ........................................................... 35 CCP Pin Configuration .............................................. 35 CCPR1H:CCPR1L Registers .................................... 35 Software Interrupt ...................................................... 35 Special Event Trigger .................................... 29, 35, 54 Timer1 Mode Selection .............................................. 35 Configuration Bits .............................................................. 55 Conversion Considerations ............................................. 103 D Data Memory ........................................................................8 Bank Select (RP1:RP0 Bits) .................................. 8, 11 General Purpose Registers ..........................................8 Register File Map .........................................................8 Special Function Registers ...........................................9 DC Characteristics ....................................................... 76, 78 Development Support ........................................................ 71 Development Tools ............................................................ 71 Direct Addressing .............................................................. 18 E Electrical Characteristics ................................................... 75 Errata ....................................................................................3 External Clock Input (RA4/T0CKI). See Timer0 External Interrupt Input (RB0/INT). See Interrupt Sources External Power-on Reset Circuit ....................................... 59 F Firmware Instructions ........................................................ 69 ftp site .............................................................................. 109 Fuzzy Logic Dev. System (fuzzyTECH-MP) ................... 73 B I Banking, Data Memory .................................................. 8, 11 BOR. See Brown-out Reset Brown-out Reset (BOR) ............................. 55, 57, 59, 60, 61 BOR Enable (BODEN Bit) .......................................... 55 BOR Status (BOR Bit) ................................................ 16 Timing Diagram .......................................................... 84 I/O Ports ............................................................................ 19 I2C (SSP Module) .............................................................. 44 ACK Pulse ......................................... 44, 45, 46, 47, 48 Addressing ................................................................. 45 Block Diagram ........................................................... 44 Buffer Full Status (BF Bit) .......................................... 40 Clock Polarity Select (CKP Bit) .................................. 41 Data/Address (D/A Bit) .............................................. 40 Master Mode .............................................................. 48 Mode Select (SSPM3:SSPM0 Bits) ........................... 41 Multi-Master Mode ..................................................... 48 Read/Write Bit Information (R/W Bit) ....... 40, 45, 46, 47 Receive Overflow Indicator (SSPOV Bit) ................... 41 Reception .................................................................. 46 Reception Timing Diagram ........................................ 46 Serial Clock (RC3/SCK/SCL) .................................... 47 Slave Mode ................................................................ 44 Start (S Bit) .......................................................... 40, 48 Stop (P Bit) .......................................................... 40, 48 Synchronous Serial Port Enable (SSPEN Bit) ........... 41 Timing Diagram, Data ................................................ 92 Timing Diagram, Start/Stop Bits ................................ 91 Transmission ............................................................. 47 Update Address (UA Bit) ........................................... 40 C Capture (CCP Module) ...................................................... 34 Block Diagram ............................................................ 34 CCP Pin Configuration ............................................... 34 CCPR1H:CCPR1L Registers ..................................... 34 Changing Between Capture Prescalers ..................... 34 Software Interrupt ...................................................... 34 Timer1 Mode Selection .............................................. 34 Capture/Compare/PWM (CCP) .......................................... 33 Capture Mode. See Capture CCP1CON Register ............................................... 9, 33 CCPR1H Register .................................................. 9, 33 CCPR1L Register .................................................. 9, 33 Compare Mode. See Compare Enable (CCP1IE Bit) .................................................. 14 Flag (CCP1IF Bit) ....................................................... 15 1998 Microchip Technology Inc. Preliminary DS35008A-page 105 PIC16C62B/72A ICEPIC Low-Cost PIC16CXXX In-Circuit Emulator ........... 71 ID Locations ................................................................. 55, 68 In-Circuit Serial Programming (ICSP) .......................... 55, 68 Indirect Addressing ............................................................ 18 FSR Register ..................................................... 8, 9, 18 INDF Register .............................................................. 9 Instruction Format .............................................................. 69 Instruction Set .................................................................... 69 Summary Table .......................................................... 70 INT Interrupt (RB0/INT). See Interrupt Sources INTCON Register ........................................................... 9, 13 GIE Bit ........................................................................ 13 INTE Bit ...................................................................... 13 INTF Bit ...................................................................... 13 PEIE Bit ...................................................................... 13 RBIE Bit ..................................................................... 13 RBIF Bit ................................................................ 13, 21 T0IE Bit ...................................................................... 13 T0IF Bit ...................................................................... 13 Inter-Integrated Circuit. See I2C Interrupt Sources .......................................................... 55, 64 A/D Conversion Complete ......................................... 51 Block Diagram ............................................................ 64 Capture Complete (CCP) ........................................... 34 Compare Complete (CCP) ......................................... 35 Interrupt on Change (RB7:RB4 ) ................................ 21 RB0/INT Pin, External ............................................ 6, 65 SSP Receive/Transmit Complete .............................. 39 TMR0 Overflow .................................................... 26, 65 TMR1 Overflow .................................................... 27, 29 TMR2 to PR2 Match .................................................. 32 TMR2 to PR2 Match (PWM) ................................ 31, 36 Interrupts, Context Saving During ...................................... 65 Interrupts, Enable Bits A/D Converter Enable (ADIE Bit) ............................... 14 CCP1 Enable (CCP1IE Bit) .................................. 14, 34 Global Interrupt Enable (GIE Bit) ......................... 13, 64 Interrupt on Change (RB7:RB4) Enable (RBIE Bit) .. 13, 65 Peripheral Interrupt Enable (PEIE Bit) ....................... 13 RB0/INT Enable (INTE Bit) ........................................ 13 SSP Enable (SSPIE Bit) ............................................ 14 TMR0 Overflow Enable (T0IE Bit) .............................. 13 TMR1 Overflow Enable (TMR1IE Bit) ........................ 14 TMR2 to PR2 Match Enable (TMR2IE Bit) ................ 14 Interrupts, Flag Bits A/D Converter Flag (ADIF Bit) ............................. 15, 51 CCP1 Flag (CCP1IF Bit) ................................ 15, 34, 35 Interrupt on Change (RB7:RB4) Flag (RBIF Bit) . 13, 21, 65 RB0/INT Flag (INTF Bit) ............................................. 13 SSP Flag (SSPIF Bit) ................................................. 15 TMR0 Overflow Flag (T0IF Bit) ............................ 13, 65 TMR1 Overflow Flag (TMR1IF Bit) ............................ 15 TMR2 to PR2 Match Flag (TMR2IF Bit) ..................... 15 K KeeLoq Evaluation and Programming Tools ................... 73 M Master Clear (MCLR) ........................................................... 6 MCLR Reset, Normal Operation .................... 57, 60, 61 MCLR Reset, SLEEP ..................................... 57, 60, 61 Memory Organization Data Memory ............................................................... 8 Program Memory ......................................................... 7 MPLAB Integrated Development Environment Software ... 72 DS35008A-page 106 O On-Line Support .............................................................. 109 OPCODE Field Descriptions .............................................. 69 OPTION_REG Register ............................................... 10, 12 INTEDG Bit ................................................................ 12 PS2:PS0 Bits ....................................................... 12, 25 PSA Bit ................................................................ 12, 25 RBPU Bit ................................................................... 12 T0CS Bit .............................................................. 12, 25 T0SE Bit .............................................................. 12, 25 OSC1/CLKIN Pin ................................................................. 6 OSC2/CLKOUT Pin ............................................................. 6 Oscillator Configuration ............................................... 55, 56 HS ........................................................................ 56, 60 LP ........................................................................ 56, 60 RC ................................................................. 56, 57, 60 Selection (FOSC1:FOSC0 Bits) ................................ 55 XT ........................................................................ 56, 60 Oscillator, Timer1 ......................................................... 27, 29 Oscillator, WDT .................................................................. 66 P Packaging .......................................................................... 97 Paging, Program Memory .............................................. 7, 17 PCON Register ............................................................ 16, 60 BOR Bit ...................................................................... 16 POR Bit ...................................................................... 16 PICDEM-1 Low-Cost PICmicro Demo Board .................... 72 PICDEM-2 Low-Cost PIC16CXX Demo Board .................. 72 PICDEM-3 Low-Cost PIC16CXXX Demo Board ............... 72 PICSTART Plus Entry Level Development System ........ 71 PIE1 Register ............................................................... 10, 14 ADIE Bit ..................................................................... 14 CCP1IE Bit ................................................................ 14 SSPIE Bit ................................................................... 14 TMR1IE Bit ................................................................ 14 TMR2IE Bit ................................................................ 14 Pinout Descriptions PIC16C62B/PIC16C72A .............................................. 6 PIR1 Register ................................................................ 9, 15 ADIF Bit ..................................................................... 15 CCP1IF Bit ................................................................. 15 SSPIF Bit ................................................................... 15 TMR1IF Bit ................................................................ 15 TMR2IF Bit ................................................................ 15 Pointer, FSR ...................................................................... 18 POR. See Power-on Reset PORTA ................................................................................ 6 Analog Port Pins .......................................................... 6 Initialization ................................................................ 19 PORTA Register .................................................... 9, 19 RA3:RA0 and RA5 Port Pins ..................................... 19 RA4/T0CKI Pin ...................................................... 6, 19 RA5/SS/AN4 Pin .................................................... 6, 42 TRISA Register .................................................... 10, 19 PORTB ................................................................................ 6 Initialization ................................................................ 21 PORTB Register .................................................... 9, 21 Pull-up Enable (RBPU Bit) ......................................... 12 RB0/INT Edge Select (INTEDG Bit) .......................... 12 RB0/INT Pin, External ........................................... 6, 65 RB3:RB0 Port Pins .................................................... 21 RB7:RB4 Interrupt on Change ................................... 65 RB7:RB4 Interrupt on Change Enable (RBIE Bit) 13, 65 RB7:RB4 Interrupt on Change Flag (RBIF Bit) 13, 21, 65 RB7:RB4 Port Pins .................................................... 21 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A TRISB Register .................................................... 10, 21 PORTC ................................................................................ 6 Block Diagram ............................................................ 23 Initialization ................................................................ 23 PORTC Register .................................................... 9, 23 RC0/T1OSO/T1CKI Pin ............................................... 6 RC1/T1OSI Pin ............................................................ 6 RC2/CCP1 Pin ............................................................. 6 RC3/SCK/SCL Pin ........................................... 6, 42, 47 RC4/SDI/SDA Pin .................................................. 6, 42 RC5/SDO Pin ......................................................... 6, 42 RC6 Pin ........................................................................ 6 RC7 Pin ........................................................................ 6 TRISC Register .................................................... 10, 23 Postscaler, Timer2 Select (TOUTPS3:TOUTPS0 Bits) ............................ 31 Postscaler, WDT ................................................................ 25 Assignment (PSA Bit) .......................................... 12, 25 Block Diagram ............................................................ 26 Rate Select (PS2:PS0 Bits) ................................. 12, 25 Switching Between Timer0 and WDT ........................ 26 Power-down Mode. See SLEEP Power-on Reset (POR) .............................. 55, 57, 59, 60, 61 Oscillator Start-up Timer (OST) ........................... 55, 59 POR Status (POR Bit) ................................................ 16 Power Control (PCON) Register ................................ 60 Power-down (PD Bit) ........................................... 11, 57 Power-on Reset Circuit, External ............................... 59 Power-up Timer (PWRT) ..................................... 55, 59 PWRT Enable (PWRTE Bit) ....................................... 55 Time-out (TO Bit) ................................................. 11, 57 Time-out Sequence .................................................... 60 Time-out Sequence on Power-up ........................ 62, 63 Timing Diagram .......................................................... 84 Prescaler, Capture ............................................................. 34 Prescaler, Timer0 ............................................................... 25 Assignment (PSA Bit) .......................................... 12, 25 Block Diagram ............................................................ 26 Rate Select (PS2:PS0 Bits) ................................. 12, 25 Switching Between Timer0 and WDT ........................ 26 Prescaler, Timer1 ............................................................... 28 Select (T1CKPS1:T1CKPS0 Bits) .............................. 27 Prescaler, Timer2 ............................................................... 36 Select (T2CKPS1:T2CKPS0 Bits) .............................. 31 PRO MATE II Universal Programmer ............................. 71 Product Identification System .......................................... 111 Program Counter PCL Register .......................................................... 9, 17 PCLATH Register ............................................ 9, 17, 65 Reset Conditions ........................................................ 60 Program Memory ................................................................. 7 Interrupt Vector ............................................................ 7 Paging .................................................................... 7, 17 Program Memory Map ................................................. 7 Reset Vector ................................................................ 7 Program Verification .......................................................... 68 Programming Pin (Vpp) ....................................................... 6 Programming, Device Instructions ..................................... 69 PWM (CCP Module) .......................................................... 36 Block Diagram ............................................................ 36 CCPR1H:CCPR1L Registers ..................................... 36 Duty Cycle .................................................................. 36 Example Frequencies/Resolutions ............................ 37 Output Diagram .......................................................... 36 Period ......................................................................... 36 Set-Up for PWM Operation ........................................ 37 1998 Microchip Technology Inc. TMR2 to PR2 Match ............................................ 31, 36 TMR2 to PR2 Match Enable (TMR2IE Bit) ................ 14 TMR2 to PR2 Match Flag (TMR2IF Bit) .................... 15 Q Q-Clock .............................................................................. 36 R RAM. See Data Memory Reader Response ............................................................ 110 Register File .........................................................................8 Register File Map .................................................................8 Reset ........................................................................... 55, 57 Block Diagram ........................................................... 58 Brown-out Reset (BOR). See Brown-out Reset (BOR) MCLR Reset. See MCLR Power-on Reset (POR). See Power-on Reset (POR) Reset Conditions for All Registers ............................. 61 Reset Conditions for PCON Register ........................ 60 Reset Conditions for Program Counter ..................... 60 Reset Conditions for STATUS Register .................... 60 Timing Diagram ......................................................... 84 WDT Reset. See Watchdog Timer (WDT) Revision History ............................................................... 103 S SEEVAL Evaluation and Programming System ............. 73 Serial Peripheral Interface. See SPI SLEEP ................................................................... 55, 57, 67 Software Simulator (MPLAB-SIM) ..................................... 73 Special Event Trigger. See Compare Special Features of the CPU ............................................. 55 Special Function Registers ...................................................9 Speed, Operating .......................................................... 1, 75 SPI (SSP Module) Block Diagram ........................................................... 42 Buffer Full Status (BF Bit) .......................................... 40 Clock Edge Select (CKE Bit) ..................................... 40 Clock Polarity Select (CKP Bit) .................................. 41 Data Input Sample Phase (SMP Bit) ......................... 40 Mode Select (SSPM3:SSPM0 Bits) ........................... 41 Receive Overflow Indicator (SSPOV Bit) ................... 41 Serial Clock (RC3/SCK/SCL) .................................... 42 Serial Data In (RC4/SDI/SDA) ................................... 42 Serial Data Out (RC5/SDO) ....................................... 42 Slave Select (RA5/SS/AN4) ...................................... 42 Synchronous Serial Port Enable (SSPEN Bit) ........... 41 SSP ................................................................................... 39 Enable (SSPIE Bit) .................................................... 14 Flag (SSPIF Bit) ......................................................... 15 I2C Mode. See I2C RA5/SS/AN4 Pin ...........................................................6 RC3/SCK/SCL Pin ........................................................6 RC4/SDI/SDA Pin .........................................................6 RC5/SDO Pin ...............................................................6 SPI Mode. See SPI SSPADD Register ..................................................... 10 SSPBUF Register .........................................................9 SSPCON Register ................................................. 9, 41 SSPSTAT Register .............................................. 10, 40 TMR2 Output for Clock Shift ................................ 31, 32 Write Collision Detect (WCOL Bit) ............................. 41 SSPCON Register ............................................................. 41 CKP Bit ...................................................................... 41 SSPEN Bit ................................................................. 41 SSPM3:SSPM0 Bits .................................................. 41 SSPOV Bit ................................................................. 41 Preliminary DS35008A-page 107 PIC16C62B/72A WCOL Bit ................................................................... 41 SSPSTAT Register ............................................................ 40 BF Bit ......................................................................... 40 CKE Bit ...................................................................... 40 D/A Bit ........................................................................ 40 P bit ...................................................................... 40, 48 R/W Bit ..................................................... 40, 45, 46, 47 S Bit ..................................................................... 40, 48 SMP Bit ...................................................................... 40 UA Bit ......................................................................... 40 Stack .................................................................................. 17 STATUS Register ..................................................... 9, 11, 65 C Bit ........................................................................... 11 DC Bit ......................................................................... 11 IRP Bit ........................................................................ 11 PD Bit ................................................................... 11, 57 RP1:RP0 Bits ............................................................. 11 TO Bit ................................................................... 11, 57 Z Bit ............................................................................ 11 Synchronous Serial Port. See SSP T T1CON Register ............................................................. 9, 27 T1CKPS1:T1CKPS0 Bits ........................................... 27 T1OSCEN Bit ............................................................. 27 T1SYNC Bit ................................................................ 27 TMR1CS Bit ............................................................... 27 TMR1ON Bit ............................................................... 27 T2CON Register ............................................................. 9, 31 T2CKPS1:T2CKPS0 Bits ........................................... 31 TMR2ON Bit ............................................................... 31 TOUTPS3:TOUTPS0 Bits .......................................... 31 Timer0 ................................................................................ 25 Block Diagram ............................................................ 25 Clock Source Edge Select (T0SE Bit) .................. 12, 25 Clock Source Select (T0CS Bit) ........................... 12, 25 Overflow Enable (T0IE Bit) ........................................ 13 Overflow Flag (T0IF Bit) ....................................... 13, 65 Overflow Interrupt ................................................ 26, 65 Prescaler. See Prescaler, Timer0 RA4/T0CKI Pin, External Clock ................................... 6 Timing Diagram .......................................................... 85 TMR0 Register ............................................................. 9 Timer1 ................................................................................ 27 Block Diagram ............................................................ 28 Capacitor Selection .................................................... 29 Clock Source Select (TMR1CS Bit) ........................... 27 External Clock Input Sync (T1SYNC Bit) ................... 27 Module On/Off (TMR1ON Bit) .................................... 27 Oscillator .............................................................. 27, 29 Oscillator Enable (T1OSCEN Bit) .............................. 27 Overflow Enable (TMR1IE Bit) ................................... 14 Overflow Flag (TMR1IF Bit) ....................................... 15 Overflow Interrupt ................................................ 27, 29 Prescaler. See Prescaler, Timer1 RC0/T1OSO/T1CKI Pin ............................................... 6 RC1/T1OSI .................................................................. 6 Special Event Trigger (CCP) ................................ 29, 35 T1CON Register .................................................... 9, 27 Timing Diagram .......................................................... 85 TMR1H Register .................................................... 9, 27 TMR1L Register ..................................................... 9, 27 Timer2 Block Diagram ............................................................ 31 Postscaler. See Postscaler, Timer2 PR2 Register .................................................. 10, 31, 36 DS35008A-page 108 Prescaler. See Prescaler, Timer2 SSP Clock Shift ................................................... 31, 32 T2CON Register .................................................... 9, 31 TMR2 Register ...................................................... 9, 31 TMR2 to PR2 Match Enable (TMR2IE Bit) ................ 14 TMR2 to PR2 Match Flag (TMR2IF Bit) .................... 15 TMR2 to PR2 Match Interrupt ........................ 31, 32, 36 Timing Diagrams I2C Reception (7-bit Address) .................................... 46 Time-out Sequence on Power-up ........................ 62, 63 Wake-up from SLEEP via Interrupt ........................... 68 Timing Diagrams and Specifications ................................. 82 A/D Conversion ......................................................... 94 Brown-out Reset (BOR) ............................................. 84 Capture/Compare/PWM (CCP) ................................. 86 CLKOUT and I/O ....................................................... 83 External Clock ........................................................... 82 I2C Bus Data .............................................................. 92 I2C Bus Start/Stop Bits .............................................. 91 Oscillator Start-up Timer (OST) ................................. 84 Power-up Timer (PWRT) ........................................... 84 Reset ......................................................................... 84 Timer0 and Timer1 .................................................... 85 Watchdog Timer (WDT) ............................................. 84 W W Register ......................................................................... 65 Wake-up from SLEEP .................................................. 55, 67 Interrupts ............................................................. 60, 61 MCLR Reset .............................................................. 61 Timing Diagram ......................................................... 68 WDT Reset ................................................................ 61 Watchdog Timer (WDT) ............................................... 55, 66 Block Diagram ........................................................... 66 Enable (WDTE Bit) .............................................. 55, 66 Postscaler. See Postscaler, WDT Programming Considerations .................................... 66 RC Oscillator ............................................................. 66 Time-out Period ......................................................... 66 Timing Diagram ......................................................... 84 WDT Reset, Normal Operation ...................... 57, 60, 61 WDT Reset, SLEEP ...................................... 57, 60, 61 WWW, On-Line Support .............................................. 3, 109 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A ON-LINE SUPPORT Systems Information and Upgrade Hot Line Microchip provides on-line support on the Microchip World Wide Web (WWW) site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape or Microsoft Explorer. Files are also available for FTP download from our FTP site. The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products. Plus, this line provides information on how customers can receive any currently available upgrade kits.The Hot Line Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-602-786-7302 for the rest of the world. Connecting to the Microchip Internet Web Site 980106 The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP service to connect to: ftp://ftp.futureone.com/pub/microchip The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: • Latest Microchip Press Releases • Technical Support Section with Frequently Asked Questions • Design Tips • Device Errata • Job Postings • Microchip Consultant Program Member Listing • Links to other useful web sites related to Microchip Products • Conferences for products, Development Systems, technical information and more • Listing of seminars and events 1998 Microchip Technology Inc. Trademarks: The Microchip name, logo, PIC, PICSTART, PICMASTER and PRO MATE are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. PICmicro, FlexROM, MPLAB, in-circuit serial programming and fuzzyLAB are trademarks and SQTP is a service mark of Microchip in the U.S.A. All other trademarks mentioned herein are the property of their respective companies. Preliminary DS35008A-page 109 PIC16C62B/72A READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (602) 786-7578. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: Technical Publications Manager RE: Reader Response Total Pages Sent From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Device: PIC16C62B/72A Y N Literature Number: DS35008A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this data sheet easy to follow? If not, why? 4. What additions to the data sheet do you think would enhance the structure and subject? 5. What deletions from the data sheet could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? 8. How would you improve our software, systems, and silicon products? DS35008A-page 110 Preliminary 1998 Microchip Technology Inc. PIC16C62B/72A PIC16C62B/72A PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X -XX Frequency Temperature Range Range /XX XXX Package Pattern Examples: a) b) Device PIC16C62B(1), PIC16C62BT(2);VDD range 4.0V to 5.5V PIC16LC62B(1), PIC16LC62BT(2);VDD range 2.5V to 5.5V PIC16C72A(1), PIC16C72AT(2);VDD range 4.0V to 5.5V PIC16LC72A(1), PIC16LC72AT(2);VDD range 2.5V to 5.5V Frequency Range 04 20 c) PIC16C72A - 04/P 301 = Commercial temp., PDIP package, 4 MHz, normal VDD limits, QTP pattern #301. PIC16LC62B - 04I/SO = Industrial temp., SOIC package, 200 kHz, Extended VDD limits. PIC16C62B - 20I/P = Industrial temp., PDIP package, 20MHz, normal VDD limits. Note 1: = 4 MHz = 20 MHz 2: Temperature Range blank I E = 0°C to 70°C = -40°C to +85°C = -40°C to +125°C Package JW SO SP P SS = = = = = Pattern QTP, SQTP, Code or Special Requirements (blank otherwise) C LC T = CMOS = Low Power CMOS = in tape and reel - SOIC, SSOP packages only. (Commercial) (Industrial) (Extended) Windowed CERDIP SOIC Skinny plastic dip PDIP SSOP * JW Devices are UV erasable and can be programmed to any device configuration. JW Devices meet the electrical requirement of each oscillator type (including LC devices). 1998 Microchip Technology Inc. Preliminary DS35008A-page 111 M WORLDWIDE SALES AND SERVICE AMERICAS AMERICAS (continued) ASIA/PACIFIC (continued) Corporate Office Toronto Singapore Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 602-786-7200 Fax: 602-786-7277 Technical Support: 602 786-7627 Web: http://www.microchip.com Microchip Technology Inc. 5925 Airport Road, Suite 200 Mississauga, Ontario L4V 1W1, Canada Tel: 905-405-6279 Fax: 905-405-6253 Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore 188980 Tel: 65-334-8870 Fax: 65-334-8850 Atlanta Hong Kong Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Microchip Asia Pacific RM 3801B, Tower Two Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2-401-1200 Fax: 852-2-401-3431 Boston Microchip Technology Inc. 5 Mount Royal Avenue Marlborough, MA 01752 Tel: 508-480-9990 Fax: 508-480-8575 Chicago Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas Microchip Technology Inc. 14651 Dallas Parkway, Suite 816 Dallas, TX 75240-8809 Tel: 972-991-7177 Fax: 972-991-8588 Dayton Microchip Technology Inc. Two Prestige Place, Suite 150 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Detroit Microchip Technology Inc. 42705 Grand River, Suite 201 Novi, MI 48375-1727 Tel: 248-374-1888 Fax: 248-374-2874 Los Angeles ASIA/PACIFIC Taiwan, R.O.C Microchip Technology Taiwan 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE India United Kingdom Microchip Technology Inc. India Liaison Office No. 6, Legacy, Convent Road Bangalore 560 025, India Tel: 91-80-229-0061 Fax: 91-80-229-0062 Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-1189-21-5858 Fax: 44-1189-21-5835 Japan Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa 222-0033 Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 France Korea Germany Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934 Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 Müchen, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Shanghai Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-39-6899939 Fax: 39-39-6899883 Microchip Technology RM 406 Shanghai Golden Bridge Bldg. 2077 Yan’an Road West, Hong Qiao District Shanghai, PRC 200335 Tel: 86-21-6275-5700 Fax: 86 21-6275-5060 Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 714-263-1888 Fax: 714-263-1338 Arizona Microchip Technology SARL Zone Industrielle de la Bonde 2 Rue du Buisson aux Fraises 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Italy 7/7/98 Microchip received ISO 9001 Quality System certification for its worldwide headquarters, design, and wafer fabrication facilities in January, 1997. Our field-programmable PICmicro™ 8-bit MCUs, Serial EEPROMs, related specialty memory products and development systems conform to the stringent quality standards of the International Standard Organization (ISO). New York Microchip Technology Inc. 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 516-273-5305 Fax: 516-273-5335 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 All rights reserved. © 1998, Microchip Technology Incorporated, USA. 8/98 Printed on recycled paper. Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of MicrochipÕs products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. DS35008A-page 112 Preliminary 1998 Microchip Technology Inc.