AD ADCMP553BRM

FEATURES
Single power supply
750 ps propagation delay input to output
100 ps propagation delay dispersion
Differential PECL compatible outputs
Differential latch control
Internal latch pull-up resistors
Power supply rejection greater than 70 dB
750 ps minimum pulse width
Equivalent input rise time bandwidth > 750 MHz
Typical output rise/fall of 500 ps
Programmable Hysteresis
APPLICATIONS
Automatic test equipment
High speed instrumentation
Scope and logic analyzer front ends
Window comparators
High speed line receivers
Threshold detection
Peak detection
High speed triggers
Patient diagnostics
Disk drive read channel detection
Hand-held test instruments
Zero crossing detectors
Line receivers and signal restoration
Clock drivers
FUNCTIONAL BLOCK DIAGRAM
NONINVERTING
INPUT
INVERTING
INPUT
Q OUTPUT
ADCMP551/
ADCMP552/
ADCMP553
Q OUTPUT
LATCH ENABLE
INPUT
LATCH ENABLE
INPUT
04722-0-001
Preliminary Technical Data
Single Supply High Speed PECL Comparators
ADCMP551/ADCMP552/ADCMP553
Figure 1.
GENERAL DESCRIPTION
The ADCMP551/ADCMP552/ADCMP553 are single supply,
high speed comparators fabricated on Analog Devices’
proprietary XFCB process. The devices feature a 750 ps
propagation delay with less than 150 ps overdrive dispersion.
Dispersion, a measure of the difference in propagation delay
under differing overdrive conditions, is a particularly important
characteristic of high speed comparators. A separate
programmable hysteresis pin is available on the ADCMP552.
A differential input stage permits consistent propagation delay
with a common-mode range from –0.2 V to VCCI – 2.0 V.
Outputs are complementary digital signals are fully compatible
with PECL 10 K and 10 KH logic families. The outputs provide
sufficient drive current to directly drive transmission lines
terminated in 50 Ω to VCCO − 2 V. A latch input is included
and permits tracking, track-and-hold, or sample-and-hold
modes of operation. The latch input pins contain internal pullups that set the latch in tracking mode when left open.
The ADCMP551/ADCMP552/ADCMP553 are specified over
the –40°C to +85°C industrial temperature range. The
ADCMP551 is available in a 16-lead QSOP package; the
ADCMP552 is available in a 20-lead QSOP package; and the
ADCMP553 is available in an 8-lead MSOP package.
Rev. PrB
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
ADCMP551/ADCMP552/ADCMP553
Preliminary Technical Data
TABLE OF CONTENTS
Specifications..................................................................................... 3
Clock Timing Recovery............................................................. 11
Absolute Maximum Ratings............................................................ 5
Optimizing High Speed Performance ..................................... 11
Thermal Considerations.............................................................. 5
Comparator Propagation Delay Dispersion ........................... 11
ESD Caution.................................................................................. 5
Comparator Hysteresis .............................................................. 12
Pin Configuration and Function Descriptions............................. 6
Minimum Input Slew Rate Requirement ................................ 12
Typical Performance Characteristics ............................................. 8
Typical Application Circuits ......................................................... 13
Timing Information ....................................................................... 10
Outline Dimensions ....................................................................... 14
Application Information................................................................ 11
Ordering Guide .......................................................................... 14
REVISION HISTORY
Revision PrA: Preliminary Version
Rev. PrB | Page 2 of 14
Preliminary Technical Data
ADCMP551/ADCMP552/ADCMP553
SPECIFICATIONS
VCCI = 3.3 V, VCCO = 3.3 V, TA = 25°C, unless otherwise noted.
Table 1. ADCMP551/ADCMP552/ADCMP553 Electrical Characteristics
Parameter
DC INPUT CHARACTERISTICS
Input Voltage Range
Input Differential Voltage Range
Input Offset Voltage
Input Offset Voltage Channel Matching
Offset Voltage Tempco
Input Bias Current
Input Bias Current Tempco
Input Offset Current
Input Capacitance
Input Resistance, Differential Mode
Input Resistance, Common Mode
Active Gain
Common-Mode Rejection Ratio
Hysteresis
LATCH ENABLE CHARACTERISTICS
Latch Enable Voltage Range
Latch Enable Differential Voltage Range
Latch Enable Input High Current
Latch Enable Input Low Current
LE Voltage, Open
LE Voltage, Open
Latch Setup Time
Latch Hold Time
Latch to Output Delay
Latch Minimum Pulse Width
DC OUTPUT CHARACTERISTICS
Output Voltage—High Level
Output Voltage—Low Level
Rise Time
Fall Time
AC PERFORMANCE
Propagation Delay
Propagation Delay Tempco
Prop Delay Skew—Rising Transition to
Falling Transition
Within Device Propagation Delay
Skew—Channel-to-Channel
Overdrive Dispersion
Overdrive Dispersion
Slew Rate Dispersion
Pulse Width Dispersion
Duty Cycle Dispersion
Common-Mode Voltage Dispersion
Symbol
Conditions
Min
VOS
−IN = 0 V, +IN = 0 V
−0.2
−3
−10.0
∆VOS/dT
IIN
−IN = −0.2 V, +IN = +1.3 V
−10.0
−3.0
CIN
AV
CMRR
VCM = −0.2 V to +1.3 V
RHYS = ∞
Typ
±3.0
±3.0
10.0
±7
0.5
±1.0
1.0
100
600
60
70
±0.5
VCCI – 1.8
0.4
−150
−150
VCCI – 0.15
VCCI/2 – 0.075
Max
Unit
VCCI – 2.0
+3
+10.0
V
V
mV
mV
µV/°C
µA
nA/°C
µA
pF
kΩ
kΩ
dB
dB
mV
+10.0
+3.0
VCCI – 0.8
1.0
+150
+150
VCCI
VCCI/2 + 0.075
V
V
µA
µA
V
V
ps
ps
ps
ps
VCCO − 0.81
VCCO − 1.54
500
500
V
V
ps
ps
tS
tH
tPLOH, tPLOL
tPL
@ VCCI – 0.8 V
@ VCCI – 1.8 V
Latch inputs not connected
Latch inputs not connected
VOD = 250 mV
VOD = 250 mV
VOD = 250 mV
VOD = 250 mV
VOH
VOL
tR
tF
PECL 50 Ω to VDD − 2.0 V
PECL 50 Ω to VDD − 2.0 V
10% to 90%
10% to 90%
tPD
VOD = 1 V
VOD = 20 mV
VOD = 1 V
VOD = 1 V
750
850
0.5
100
ps
ps
ps/°C
ps
VOD = 1 V
100
ps
50 mV ≤ VOD ≤ 100 mV
100 mV ≤ VOD ≤ 1.5 V
0.4 V/ns ≤ SR ≤ 1.33 V/ns
750 ps ≤ PW ≤ 10 ns
33 MHz, 1 V/ns, VCM = 0.5 V
1 V swing, 0.3 V ≤ VCM ≤ 0.8 V
100
100
100
50
50
100
ps
ps
ps
ps
ps
ps
∆tPD/dT
Rev. PrB | Page 3 of 14
500
500
750
750
VCCO − 1.05
VCCO − 1.95
ADCMP551/ADCMP552/ADCMP553
Parameter
AC PERFORMANCE (continued)
Equivalent Input Rise Time Bandwidth1
Maximum Toggle Rate
Minimum Pulse Width
Unit-to-Unit Propagation Delay Skew
POWER SUPPLY (ADCMP551/ADCMP552)
Input Supply Current
Output Supply Current
Output Supply Current
Input Supply Voltage
Output Supply Voltage
Positive Supply Differential
Power Dissipation
Power Dissipation
DC Power Supply Rejection Ratio—VCCI
DC Power Supply Rejection Ratio—VCCO
POWER SUPPLY (ADCMP553)
Positive Supply Current
Positive Supply Current
Positive Supply Voltage
Power Dissipation
Power Dissipation
DC Power Supply Rejection Ratio — VCC
HYSTERESIS (ADCMP552 Only)
Programmable Hysteresis
1
Preliminary Technical Data
Symbol
Conditions
BWEQ
0 V to 1 V swing, 2 V/ns
>50% output swing
∆tPD < 50 ps
750
650
750
100
@ 3.3 V
@ 3.3 V without load
@ 3.3 V with load
Dual
Dual
12.5
6
62
3.3
3.3
PWMIN
IVCCI
IVCCO
VCCI
VCCO
VCCO − VCCI
PD
Min
3.135
3.135
–0.2
Dual, without load
Dual, with load
55
115
70
70
@ 3.3 V without load
@ 3.3 V with load
Dual
Dual, without load
Dual, with load
9
35
3.3
30
60
70
PSRRVCCI
PSRRVCCO
IVCC
VCC
PD
Typ
3.135
PSRRVCC
0
Max
Unit
MHz
MHz
ps
ps
16
9
70
5.25
5.25
+2.3
70
140
mA
mA
mA
V
V
V
mW
mW
dB
dB
11
42
5.25
40
75
mA
mA
V
mW
mW
dB
40
mV
Equivalent input rise time bandwidth assumes a first order input response and is calculated by the following formula: BWEQ = .22/√(trCOMP2-trIN2), where trIN is the 20/80
input transition time applied to the comparator and trCOMP is the effective transition time as digitized by the comparator input.
Rev. PrB | Page 4 of 14
Preliminary Technical Data
ADCMP551/ADCMP552/ADCMP553
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Supply Voltages
Input Supply Voltage (VCCI to GND)
Output Supply Voltage (VCCO to GND)
Ground Voltage Differential
Input Voltages
Input Common-Mode Voltage
Differential Input Voltage
Input Voltage, Latch Controls
Output
Output Current
Temperature
Operating Temperature, Ambient
Operating Temperature, Junction
Storage Temperature Range
Rating
−0.5 V to +6.0 V
−0.5 V to +6.0 V
−0.5 V to +0.5 V
−0.5 V to +3.5 V
−4.0 V to +4.0 V
−0.5 V to +5.5 V
30 mA
−40°C to +85°C
125°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may
affect device reliability.
THERMAL CONSIDERATIONS
The ADCMP551 16-lead QSOP package has a θJA (junction-toambient thermal resistance) of TBD°C/W in still air.
The ADCMP552 20-lead QSOP package has a θJA (junction-toambient thermal resistance) of TBD°C/W in still air.
The ADCMP553 8-lead MSOP package has a θJA (junction-toambient thermal resistance) of TBD°C/W in still air.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrB | Page 5 of 14
ADCMP551/ADCMP552/ADCMP553
Preliminary Technical Data
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
20 VCCO
VCCO 1
VCCO 3
LEA 4
LEA 5
ADCMP551
TOP VIEW
(Not to Scale)
QB
14
VCCO
13
LEB
12
LEB
VCCI 6
11
AGND
–INA 7
10
–INB
+INA 8
9
+INB
19 QB
QA 3
Figure 2. ADCMP551 16-Lead QSOP Pin
Configuration
18 QB
VCCO 4
ADCMP552
LEA 5
TOP VIEW
(Not to Scale)
LEA 1
17 VCCO
16 LEB
LEA 6
15 LEB
VCCI 7
14 AGND
–INA 8
13 –INB
+INA 9
12 +INB
HYSA 10
11 HYSB
LEA 2
ADCMP553
+INA 3
TOP VIEW
(Not to Scale)
–INA 4
8
AGND
7
VCC
6 QA
5
QA
04722-0-004
15
QA 2
QB
04722-0-003
16
04722-0-002
QA 1
QA 2
Figure 3. ADCMP552 20-Lead QSOP Pin
Configuration
Figure 4. ADCMP553 8-Lead MSOP Pin Configuration
Table 3. ADCMP551/ADCMP552/ADCMP553 Pin Function Descriptions
ADCMP551
3, 14
1
Pin No.
ADCMP552
1, 4, 17, 20
2
2
6
Mnemonic
VCCO
QA
3
5
QA
4
5
2
LEA
5
6
1
LEA
6
7
7
8
4
VCCI
−INA
8
9
3
+INA
9
10
11
12
HYSA
HYSB
+INB
10
13
−INB
11
14
ADCMP553
8
AGND
Function
Logic Supply Terminal.
One of Two Complementary Outputs for Channel A. QA is logic high if the
analog voltage at the noninverting input is greater than the analog voltage at
the inverting input (provided the comparator is in the compare mode). See the
description of Pin LEA for more information.
One of Two Complementary Outputs for Channel A. QA is logic low if the analog
voltage at the noninverting input is greater than the analog voltage at the
inverting input (provided the comparator is in the compare mode). See the
description of Pin LEA for more information.
One of Two Complementary Outputs for Channel A Latch Enable. In the
compare mode (logic high), the output tracks changes at the input of the
comparator. In the latch mode (logic low), the output reflects the input state just
prior to the comparator’s being placed in the latch mode. LEA must be driven in
conjunction with LEA.
One of Two Complementary Outputs for Channel A Latch Enable. In the
compare mode (logic high), the output tracks changes at the input of the
comparator. In the latch mode (logic low), the output reflects the input state just
prior to the comparator’s being placed in the latch mode. LEA must be driven in
conjunction with LEA.
Input Supply Terminal.
Inverting Analog Input of the Differential Input Stage for Channel A. The
inverting A input must be driven in conjunction with the noninverting A input.
Noninverting Analog Input of the Differential Input Stage for Channel A. The
noninverting A input must be driven in conjunction with the inverting A input.
Programmable Hysteresis.
Programmable Hysteresis.
Noninverting Analog Input of the Differential Input Stage for Channel B. The
noninverting B input must be driven in conjunction with the inverting B input.
Inverting Analog Input of the Differential Input Stage for Channel B. The
inverting B input must be driven in conjunction with the noninverting B input.
Analog Ground.
Rev. PrB | Page 6 of 14
Preliminary Technical Data
ADCMP551/ADCMP552/ADCMP553
ADCMP551
12
Pin No.
ADCMP552
15
13
16
LEB
15
18
QB
16
19
QB
ADCMP553
7
Mnemonic
LEB
VCC
Function
One of Two Complementary Inputs for Channel B Latch Enable. In the compare
mode (logic low), the output tracks changes at the input of the comparator. In
the latch mode (logic high), the output reflects the input state just prior to the
comparator’s being placed in the latch mode. LEB must be driven in conjunction
with LEB.
One of Two Complementary Inputs for Channel B Latch Enable. In the compare
mode (logic low), the output tracks changes at the input of the comparator. In
the latch mode (logic high), the output reflects the input state just prior to the
comparator’s being placed in the latch mode. LEB must be driven in conjunction
with LEB.
One of Two Complementary Outputs for Channel B. QB is logic low if the analog
voltage at the noninverting input is greater than the analog voltage at the
inverting input (provided the comparator is in the compare mode). See the
description of Pin LEB for more information.
One of Two Complementary Outputs for Channel B. QB is logic low if the analog
voltage at the noninverting input is greater than the analog voltage at the
inverting input (provided the comparator is in the compare mode). See the
description of Pin LEB for more information.
Positive Supply Terminal.
Rev. PrB | Page 7 of 14
ADCMP551/ADCMP552/ADCMP553
Preliminary Technical Data
TYPICAL PERFORMANCE CHARACTERISTICS
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
ALL CAPS (Initial caps)
VCCI = 3.3 V, VCCO = 3.3 V, TA = 25°C, unless otherwise noted.
TBD
–000
–000
–000
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
–000
–000
–000
–000
–000
–000
–000
TBD
–000
–000
–000
–000
ALL CAPS (Initial caps)
–000
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
ALL CAPS (Initial caps)
–000
TBD
TBD
–000
–000
–000
ALL CAPS (Initial caps)
–000
–000
TBD
–000
–000
–000
–000
–000
Figure 9. Hysteresis vs. ∆Latch
Figure 6. Input Offset Voltage vs. Temperature
–000
–000
–000
ALL CAPS (Initial caps)
–000
–000
–000
–000
–000
Figure 8. Input Bias Current vs. Temperature
ALL CAPS (Initial caps)
ALL CAPS (Initial caps)
Figure 5. Input Bias Current vs. Input Voltage
–000
TBD
–000
–000
–000
ALL CAPS (Initial caps)
–000
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
Figure 10. Fall Time vs. Temperature
Figure 7. Rise Time vs. Temperature
Rev. PrB | Page 8 of 14
–000
ADCMP551/ADCMP552/ADCMP553
–000
–000
–000
–000
ALL CAPS (Initial caps)
ALL CAPS (Initial caps)
Preliminary Technical Data
TBD
–000
–000
–000
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
–000
–000
–000
–000
–000
–000
–000
TBD
–000
–000
–000
–000
ALL CAPS (Initial caps)
–000
Figure 14. Propagation Delay vs. Common-Mode Voltage
ALL CAPS (Initial caps)
ALL CAPS (Initial caps)
Figure 11. Propagation Delay vs. Temperature
–000
TBD
–000
–000
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
–000
Figure 12. Propagation Delay vs. Overdrive Voltage
–000
–000
TBD
–000
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
Figure 15. Propagation Delay Error vs. Pulse Width
–000
ALL CAPS (Initial caps)
TBD
–000
–000
Figure 13. Rise and Fall of Outputs vs. Time
Rev. PrB | Page 9 of 14
–000
ADCMP551/ADCMP552/ADCMP553
Preliminary Technical Data
TIMING INFORMATION
LATCH ENABLE
50%
LATCH ENABLE
tS
tPL
tH
DIFFERENTIAL
INPUT VOLTAGE
VIN
VREF ± VOS
VOD
tPDL
tPLOH
Q OUTPUT
50%
tF
tPDH
tPLOL
tR
04687-0-004
50%
Q OUTPUT
Figure 16. System Timing Diagram
Figure 16 shows the compare and latch features of the ADCMP55x family. Table 4 describes the terms in the diagram.
Table 4. Timing Descriptions
Symbol
tPDH
Timing
Input to Output High Delay
tPDL
Input to Output Low Delay
tPLOH
Latch Enable to Output High Delay
tPLOL
Latch Enable to Output Low Delay
tH
Minimum Hold Time
tPL
tS
Minimum Latch Enable Pulse Width
Minimum Setup Time
tR
Output Rise Time
tF
Output Fall Time
VOD
Voltage Overdrive
Description
Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output low-to-high transition
Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output high-to-low transition
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output low-to-high transition
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output high-to-low transition
Minimum time after the negative transition of the latch enable signal that the input signal
must remain unchanged to be acquired and held at the outputs
Minimum time the latch enable signal must be high to acquire an input signal change
Minimum time before the negative transition of the latch enable signal that an input
signal change must be present to be acquired and held at the outputs
Amount of time required to transition from a low to a high output as measured at the
20% and 80% points
Amount of time required to transition from a high to a low output as measured at the
20% and 80% points
Difference between the differential input and reference input voltages
Rev. PrB | Page 10 of 14
Preliminary Technical Data
ADCMP551/ADCMP552/ADCMP553
APPLICATION INFORMATION
The ADCMP55x series of comparators are very high speed
devices. Consequently, high speed design techniques must be
employed to achieve the best performance. The most critical
aspect of any ADCMP55x design is the use of a low impedance
ground plane. A ground plane, as part of a multilayer board, is
recommended for proper high speed performance. Using a
continuous conductive plane over the surface of the circuit
board can create this, allowing breaks in the plane only for
necessary signal paths. The ground plane provides a low
inductance ground, eliminating any potential differences at
different ground points throughout the circuit board caused by
ground bounce. A proper ground plane also minimizes the
effects of stray capacitance on the circuit board.
It is also important to provide bypass capacitors for the power
supply in a high speed application. A 1 µF electrolytic bypass
capacitor should be placed within 0.5 inches of each power
supply pin to ground. These capacitors reduce any potential
voltage ripples from the power supply. In addition, a 10 nF
ceramic capacitor should be placed as close to the power supply
pins as possible on the ADCMP55x to ground. These capacitors
act as a charge reservoir for the device during high frequency
switching.
The LATCH ENABLE input is active low (latched). If the
latching function is not used, the LATCH ENABLE input pins
may be left open. The internal pull-ups on the latch pins set the
latch to transparent mode. If the latch is to be used, valid PECL
voltages are required on the inputs for proper operation. The
PECL voltages should be referenced to VCCI.
Occasionally, one of the two comparator stages within the
ADCMP551/ADCMP552 is not used. The inputs of the unused
comparator should not be allowed to float. The high internal
gain may cause the output to oscillate (possibly affecting the
comparator that is being used) unless the output is forced into a
fixed state. This is easily accomplished by ensuring that the two
inputs are at least one diode drop apart, while also appropriately
connecting the LATCH ENABLE and LATCH ENABLE inputs
as described previously.
The best performance is achieved with the use of proper PECL
terminations. The open-emitter outputs of the ADCMP55x are
designed to be terminated through 50 Ω resistors to
VCCO − 2.0 V or any other equivalent PECL termination. If high
speed PECL signals must be routed more than a centimeter,
microstrip or stripline techniques may be required to ensure
proper transition times and prevent output ringing.
CLOCK TIMING RECOVERY
Comparators are often used in digital systems to recover clock
timing signals. High speed square waves transmitted over a
distance, even tens of centimeters, can become distorted due to
stray capacitance and inductance. Poor layout or improper
termination can also cause reflections on the transmission line,
further distorting the signal waveform. A high speed
comparator can be used to recover the distorted waveform
while maintaining a minimum of delay.
OPTIMIZING HIGH SPEED PERFORMANCE
As with any high speed comparator amplifier, proper design
and layout techniques should be used to ensure optimal
performance from the ADCMP55x. The performance limits of
high speed circuitry can easily be a result of stray capacitance,
improper ground impedance, or other layout issues.
Minimizing resistance from source to the input is an important
consideration in maximizing the high speed operation of the
ADCMP55x. Source resistance in combination with equivalent
input capacitance can cause a lagged response at the input, thus
delaying the output. The input capacitance of the ADCMP55x,
in combination with stray capacitance from an input pin to
ground, could result in several picofarads of equivalent
capacitance. A combination of 3 kΩ source resistance and 5 pF
input capacitance yields a time constant of 15 ns, which is
significantly slower than the 750 ps capability of the
ADCMP55x. Source impedances should be significantly less
than 100 Ω for best performance.
Sockets should be avoided due to stray capacitance and inductance. If proper high speed techniques are used, the
ADCMP55x should be free from oscillation when the
comparator input signal passes through the switching threshold.
COMPARATOR PROPAGATION DELAY
DISPERSION
The ADCMP55x has been specifically designed to reduce
propagation delay dispersion over an input overdrive range of
100 mV to 1 V. Propagation delay overdrive dispersion is the
change in propagation delay that results from a change in the
degree of overdrive (how far the switching point is exceeded by
the input). The overall result is a higher degree of timing
accuracy since the ADCMP55x is far less sensitive to input
variations than most comparator designs.
Rev. PrB | Page 11 of 14
ADCMP551/ADCMP552/ADCMP553
Preliminary Technical Data
Propagation delay dispersion is an important specification in
critical timing applications such as ATE, bench instruments,
and nuclear instrumentation. Overdrive dispersion is defined as
the variation in propagation delay as the input overdrive conditions are changed (Figure 17). For the ADCMP55x, overdrive
dispersion is typically 100 ps as the overdrive is changed from
100 mV to 1 V. This specification applies for both positive and
negative overdrive since the ADCMP55x has equal delays for
positive- and negative-going inputs.
introducing a differential voltage between the LATCH ENABLE
and LATCH ENABLE. inputs (Figure 23).
+VH
2
–VH
2
0V
INPUT
1
1.5V OVERDRIVE
INPUT VOLTAGE
0
VREF ± VOS
OUTPUT
Q OUTPUT
Figure 18. Comparator Hysteresis Transfer Function
04687-0-005
DISPERSION
04687-0-006
20mV OVERDRIVE
–000
COMPARATOR HYSTERESIS
The addition of hysteresis to a comparator is often useful in a
noisy environment, or where it is not desirable for the
comparator to toggle between states when the input signal is at
the switching threshold. The transfer function for a comparator
with hysteresis is shown in Figure 18. If the input voltage
approaches the threshold from the negative direction, the
comparator switches from a 0 to a 1 when the input crosses
+VH/2. The new switching threshold becomes −VH/2. The
comparator remains in a 1 state until the −VH/2 threshold is
crossed coming from the positive direction. In this manner,
noise centered on 0 V input does not cause the comparator to
switch states unless it exceeds the region bounded by ±VH/2.
Positive feedback from the output to the input is often used to
produce hysteresis in a comparator (Figure 22). The major
problem with this approach is that the amount of hysteresis
varies with the output logic levels, resulting in a hysteresis that
is not symmetrical around zero.
In the ADCMP552, hysteresis is generated through the
programmable hysteresis pin. A resistor from the HYS pin to
VCCI creates a current into the part that is used to generate
hysteresis. Hysteresis generated in this manner is independent
of output swing and is symmetrical around the trip point. The
hysteresis versus resistance curve is shown in Figure 19.
ALL CAPS (Initial caps)
Figure 17. Propagation Delay Dispersion
–000
TBD
–000
–000
–000
–000
–000
–000
–000
ALL CAPS (Initial caps)
–000
Figure 19. Comparator Hysteresis Transfer Function
MINIMUM INPUT SLEW RATE REQUIREMENT
As for all high speed comparators, a minimum slew rate must
be met to ensure that the device does not oscillate when the
input crosses the threshold. This oscillation is due in part to the
high input bandwidth of the comparator and the parasitics of
the package. Analog Devices recommends a slew rate of 1 V/µs
or faster to ensure a clean output transition. If slew rates less
than 1 V/µs are used, hysteresis should be added to reduce the
oscillation.
Another method to implement hysteresis is generated by
Rev. PrB | Page 12 of 14
Preliminary Technical Data
ADCMP551/ADCMP552/ADCMP553
TYPICAL APPLICATION CIRCUITS
ALL RESISTORS 50Ω
VIN
+
ADCMP551/
ADCMP552/
ADCMP553
–
–VREF
+
ADCMP551/
ADCMP552/
ADCMP553
–
R2
VCCO – 2V
ALL RESISTORS 50Ω
Figure 20. High Speed Sampling Circuits
Figure 22. Hysteresis Using Positive Feedback
+
ADCMP551/
ADCMP552/
ADCMP553
–
VIN
OUTPUTS
HYSTERESIS
VOLTAGE
OUTPUTS
VCCO – 2V
450Ω
ALL RESISTORS 50Ω UNLESS OTHERWISE NOTED
Figure 23. Hysteresis Using Latch Enable Input
LATCH
ENABLE
INPUTS
VCCO – 2V
ALL RESISTORS 50Ω
04722-0-010
+VREF
R1
04722-0-009
VCCO – 2V
OUTPUTS
04722-0-011
VREF
LATCH
ENABLE
INPUTS
+
ADCMP551/
ADCMP552/
ADCMP553
–
VIN
OUTPUTS
04722-0-012
VREF
+
ADCMP551/
ADCMP552/
ADCMP553
–
VIN
Figure 21. High Speed Window Comparator
+
ADCMP551/
ADCMP552/
ADCMP553
–
100Ω
50Ω
50Ω
50Ω
50Ω
100Ω
(VCCO – 2V) × 2
Figure 24. How to Interface a PECL Output to an
Instrument with a 50 Ω to Ground Input
Rev. PrB | Page 13 of 14
04722-0-013
VIN
ADCMP551/ADCMP552/ADCMP553
Preliminary Technical Data
OUTLINE DIMENSIONS
0.341
BSC
20
11
0.154
BSC
1
0.236
BSC
10
PIN 1
0.065
0.049
0.010
0.004
0.069
0.053
0.025
BSC
0.012
0.008
COPLANARITY
0.004
SEATING
PLANE
8°
0°
0.010
0.006
0.050
0.016
COMPLIANT TO JEDEC STANDARDS MO-137AD
Figure 25. 20-Lead Shrink Small Outline Package [QSOP]
(RQ-20)
Dimensions shown in inches
0.193
BSC
3.00
BSC
8
9
16
0.154
BSC
1
4.90
BSC
4
0.236
BSC
8
5
3.00
BSC
PIN 1
0.65 BSC
PIN 1
0.069
0.053
0.065
0.049
0.010
0.025
0.004
BSC
COPLANARITY
0.004
0.012
0.008
SEATING
PLANE
1.10 MAX
0.15
0.00
0.010
0.006
8°
0°
0.38
0.22
COPLANARITY
0.10
0.050
0.016
0.23
0.08
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187AA
COMPLIANT TO JEDEC STANDARDS MO-137AB
Figure 27. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
Figure 26. 16-Lead Shrink Small Outline Package[QSOP]
(RQ-16)
Dimensions shown in inches
ORDERING GUIDE
Model
ADCMP551BRQ
ADCMP552BRQ
ADCMP553BRM
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead QSOP
20-Lead QSOP
8-Lead MSOP
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR04687–0–7/04(PrB)
Rev. PrB | Page 14 of 14
Package Option
RQ-16
RQ-20
RM-8
0.80
0.60
0.40