AD ADCMP608

Rail-to-Rail, Fast, Low Power, 2.5 V to 5.5 V,
Single-Supply TTL/CMOS Comparators
Preliminary Technical Data
ADCMP608/ACMP609
FUNCTIONAL BLOCK DIAGRAMS
FEATURES
10 mV sensitivity rail to rail at VCC = 2.5 V
Input common-mode voltage from −0.2 V to VCC + 0.2 V
Low glitch CMOS-/TTL-compatible output stage
30 ns propagation delay
1 mW at 2.5 V
Shutdown pin
Single-pin control for programmable hysteresis and latch
Power supply rejection >60 dB
−40C° to +125C° operation
NONINVERTING
INPUT
+
ADCMP608
INVERTING
INPUT
Q OUTPUT
–
SDN
NONINVERTING
INPUT
APPLICATIONS
+
Q OUTPUT
ADCMP609
INVERTING
INPUT
Q OUTPUT
–
LE/HYS
SDN
05918-001
High speed instrumentation
Clock and data signal restoration
Logic level shifting or translation
High speed line receivers
Threshold detection
Peak and zero-crossing detectors
High speed trigger circuitry
Pulse-width modulators
Current-/voltage-controlled oscillators
Figure 1.
GENERAL DESCRIPTION
The ADCMP608 and ADCMP609 are fast comparators
fabricated on Analog Devices’ proprietary XFCB2 process.
These comparators are exceptionally versatile and easy to use.
Features include an input range from VEE − 0.5 V to VCC + 0.5 V,
low noise, TTL-/CMOS-compatible output drivers, and latch
inputs with adjustable hysteresis and/or shutdown inputs.
The TTL-/CMOS-compatible output stage is designed to drive
up to 15 pF with full rated timing specs and to degrade in a
graceful and linear fashion as additional capacitance is added.
The comparator input stage offers robust protection against
large input overdrive, and the outputs do not phase reverse
when the valid input signal range is exceeded. High speed latch
and programmable hysteresis features are also provided in a
unique single-pin control option.
The devices offer 30 ns propagation delays driving a 15 pF load
with 5 mV overdrive on 350/400 μA typical supply current. A
flexible power supply scheme allows the devices to operate with
a single +2.5 V positive supply and a −0.5 V to +3.0 V input
signal range up to a +5.5 V positive supply with a −0.5 V to +6V
input signal range. Split input/output supplies, with no
sequencing restrictions on the ADCMP609, support a wide
input signal range while allowing independent output swing
control.
The ADCMP608 is available in a tiny 6-lead SC70 package with
single-ended output and a shutdown pin.
The ADCMP609, available in an 8-lead MSOP package, features
a shutdown pin, single pin latch, and hysteresis control.
+
Rev. PrA
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADCMP608/ADCMP609
Preliminary Technical Data
TABLE OF CONTENTS
Features .............................................................................................. 1
Application Information...................................................................9
Applications....................................................................................... 1
Power/Ground Layout and Bypassing........................................9
Functional Block Diagrams............................................................. 1
TTL-/CMOS-Compatible Output Stage.........................................9
General Description ......................................................................... 1
Using/Disabling the Latch Feature..............................................9
Revision History ............................................................................... 2
Optimizing Performance..............................................................9
Specifications..................................................................................... 3
Comparator Propagation Delay Dispersion ........................... 10
Electrical Characteristics............................................................. 3
Comparator Hysteresis .............................................................. 10
Absolute Maximum Ratings............................................................ 5
Crossover Bias Point .................................................................. 11
Thermal Resistance ...................................................................... 5
Minimum Input Slew Rate Requirement ................................ 11
ESD Caution.................................................................................. 5
Typical Application Circuits ......................................................... 12
Pin Configuration and Function Descriptions............................. 6
Timing Information ....................................................................... 13
Typical Performance Characteristics ............................................. 7
REVISION HISTORY
2/06—Revision PrA: Preliminary Version
Rev. PrA | Page 2 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VCCI = VCCO = 3.3 V, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
DC INPUT CHARACTERISTICS
Voltage Range
Common-Mode Range
Differential Voltage
Offset Voltage
Bias Current
Offset Current
Capacitance
Resistance, Differential Mode
Resistance, Common Mode
Active Gain
Common-Mode Rejection
Hysteresis
LATCH ENABLE PIN CHARACTERISTICS
ADCMP609 only
VIH
VIL
LIH
IOL
HYSTERESIS MODE AND TIMING
Hysteresis Mode Bias Voltage
Minimum Resistor Value
Latch Setup Time
Latch Hold Time
Latch to Output Delay
Latch Minimum Pulse Width
SHUTDOWN PIN CHARACTERISTICS
VIH
VIL
IIH
IOL
Sleep Time
Wake-Up Time
DC OUTPUT CHARACTERISTICS
Output Voltage High Level
Output Voltage Low Level
Symbol
Conditions
Min
VP, VN
VCC = 2.5 V to 5.5 V
VCC = 2.5 V to 5.5 V
VCC = 2.5 V to 5.5 V
−0.5
−0.2
VOS
IP, IN
−5.0
−2.0
−0.5
CP, CN
0.1 V to VCC
−0.5 V to VCC + 0.5 V
AV
CMRR
tS
tH
tPLOH, tPLOL
tPL
tSD
tH
VOH
VOL
VCCI = 2.5 V, VCCO = 2.5 V,
VCM = −0.2 V to 2.7 V
VCCI = 5.5 V, VCCO = 5.5 V,
VCM = −0.2 V to 5.7 V
RHYS = ∞
Hysteresis is shut off
Latch mode guaranteed
VIH = VCCO + 0.2 V
VIL = 0.4 V
2.0
−0.2
Current sink 0 μA
Hysteresis = 60 mV
VOD = 100 mV
VOD = 100 mV
VOD = 100 mV
VOD = 100 mV
1.08
60
Comparator is operating
Shutdown guaranteed
VIH = VCC
VIL = 0 V
ICC < 100 μA
VOD = 10 mV, output valid
VCCO = 2.5 V to 6 V
IOH = 1.6 mA VCCO = 2.5 V
IOL = 1.6 mA VCCO = 2.5 V
2.0
−0.2
Rev. PrA | Page 3 of 16
Typ
Max
Unit
VCC + 0.5 V
VCC + 0.2 V
VCC
+5.0
+2.0
+0.5
TBD
150
100
80
50
V
V
V
mV
μA
μA
pF
kΩ
kΩ
dB
dB
60
dB
0.1
mV
±1
0.4
1.25
VCCO + 0.2
0.8
0.1
−0.1
V
V
mA
mA
1.35
V
kΩ
ns
ns
ns
ns
VCC
0.6
0.05
−0.05
V
V
mA
mA
ns
ns
15
20
20
20
0.4
0.6
3
VCC − 0.4
0.4
V
V
ADCMP608/ADCMP609
Parameter
AC PERFORMANCE
Propagation Delay, CL = 15 pF
Symbol
tPD
Propagation Delay Skew—Rising to
Falling Transition
Overdrive Dispersion
Slew Rate Dispersion
Small Signal
10% − 90% Duty Cycle Dispersion
Common-Mode Dispersion
Toggle Rate
RMS Random Jitter
Minimum Pulse Width
Rise Time
RJ
PWMIN
tR
Fall Time
tF
POWER SUPPLY
Input Supply Voltage Range
Output Supply Voltage Range
Positive Supply Differential
(ADCMP609)
Positive Supply Differential
(ADCMP609)
Positive Supply Current
Positive Supply Current
Input Section Supply Current
(ADCMP609)
Output Stage Supply Current
(ADCMP609)
Power Dissipation
Shutdown Current
Power Supply Rejection
Preliminary Technical Data
Conditions
VCCI = VCCO = 2.5 V to 5.5 V
VCCO = 5.5 V to 2.5 V,
VOD = 10 mV
VCCO = 2.5 V/5.5 V,
VOD = 200 mV
VOD = 10 mV
Min
Typ
Max
Unit
30
ns
25/30
ns
2
ns
10 mV < VOD < 500 mV
10 V/μs to 0.1 V/ns
200 mV p-p single ended
VOD 1.25 V, 50 V/μs,
VCM = 1.25 V
VCM = 0 V to VCC
200 m p-p single ended
>50% output swing
CL = 15 pF VCCI = 5 V
VOD = 200 mV, 5 V/ns
ΔtPD/ΔPW < 500 ps
10% to 90% CLOAD = 15 pF,
VCCI = 2.5 V to 5 V
4
1
ns
ns
1
ns
0.5
ns
TBD
Mbps
TBD
35
25 to 40
ns
ns
ns
10% to 90% CLOAD = 15 pF,
VCCI = 2.5 V to 5 V
25 to 40
ns
VCCI
VCCO
VCCI − VCCO Operating
2.5
2.5
−3
5.5
5.5
+3
V
V
V
VCCI − VCCO Nonoperating
−5.5
+5.5
V
IVCC
IVCC
IVCCi
VCC = 2.5 V
VCC = 5.5 V
VCCI = 2.5 V
400
500
270
μA
μA
mA
IVCCO
VCCO= 2.5 V
130
mA
PD
ISD
PSRR
VCC = 2.5 V
VCC =2.5 V to 5.5 V
VCCI = 2.5 V to 5 V
1
50
>50 dB
mW
μA
dB
Rev. PrA | Page 4 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Supply Voltages
Input Supply Voltage (VCCI to GND)
Output Supply Voltage
(VCCO to GND)
Positive Supply Differential
(VCCI − VCCO)
Input Voltages
Input Voltage
Differential Input Voltage
Maximum Input/Output Current
Shutdown Control Pin
Applied Voltage (HYS to GND)
Maximum Input/Output Current
Latch/Hysteresis Control Pin
Applied Voltage (HYS to GND)
Maximum Input/Output Current
Output Current
Temperature
Operating Temperature, Ambient
Operating Temperature, Junction
Storage Temperature Range
Stress above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rating
−0.5 V to +6.0 V
−0.5 V to +6.0 V
−6.0 V to +6.0 V
THERMAL RESISTANCE
−0.5 V to VCCI + 0.5 V
±(VCCI + 0.5 V)
±50mA
−0.5 V to Vcco + 0.5 V
±50 mA
−0.5 V to VCCO + 0.5 V
±50 mA
±50 mA
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type
ADCMP608 SC70 6-lead
ADCMP609 MSOP 8-lead
1
Measurement in still air.
−40°C to +125°C
150°C
−65°C to +150°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrA | Page 5 of 16
θJA 1
426
130
Unit
°C/W
°C/W
ADCMP608/ADCMP609
Preliminary Technical Data
Q 1
6
VCC
VCC 1
ADCMP608
VP 3
TOP VIEW
(Not to Scale)
5
4
SDN
VN
VN 3
05918-002
VEE 2
VP 2
SDN 4
Figure 2. ADCMP608 Pin Configuration
8
Q
ADCMP609
7
TOP VIEW
(Not to Scale)
Q
6
VEE
5
LE/HYS
05918-003
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. ADCMP609 Pin Configuration
Table 4. ADCMP608 Pin Function Descriptions
Pin No.
1
Mnemonic
Q
2
3
4
5
6
VEE
VP
Vn
SDN
VCC
Description
Noninverting Output. Q is at logic high if the analog voltage at the noninverting input, VP, is greater than the
analog voltage at the inverting input, VN.
Negative Supply Voltage.
Noninverting Analog Input.
Inverting Analog Input.
Shutdown. Drive this pin low to shutdown the device.
VCC Supply.
Table 5. ADCMP609 Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
Mnemonic
VCCI/VCCO
VP
Vn
SDN
LE/HYS
VEE
Q
8
Q
Description
Vcc Supply.
Noninverting Analog Input.
Inverting Analog Input.
Shutdown. Drive this pin low to shutdown the device.
Latch/Hysteresis Control. Bias with resistor or current source for hysteresis; drive TTL low to latch.
Negative Supply Voltage.
Noninverting Output. Q is at logic low if the analog voltage at the noninverting input, VP, is greater than the
analog voltage at the inverting input, VN, provided the comparator is in compare mode.
Inverting Output. Q is at logic high if the analog voltage at the noninverting input VP is greater than the analog
voltage at the inverting input, VN, provided the comparator is in compare mode.
Rev. PrA | Page 6 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
TYPICAL PERFORMANCE CHARACTERISTICS
VCCI = VCCO = 3.3 V, TA = 25°C, unless otherwise noted.
Figure 4. Propagation Delay vs. Input Overdrive
Figure 7. Hysteresis vs. Vcc
Figure 5. Propagation Delay vs. Input Common Mode
Figure 8. Hysteresis vs. RHYS Control Resistor
Figure 6. Propagation Delay vs. Temperature
Figure 9. Input Bias Current vs. Input Common Mode
Rev. PrA | Page 7 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
Figure 10. Input Bias Current vs. Temperature
Figure 12 Latch/Hysteresis Control Pin I/V Characteristic.
Figure 11. Input Offset Voltage vs. Temperature
Rev. PrA | Page 8 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
APPLICATION INFORMATION
POWER/GROUND LAYOUT AND BYPASSING
VLOGIC
It is also important to adequately bypass the input and output
supplies. A 0.1 μF bypass capacitor should be placed as close as
possible to each VCC supply pin. The capacitor should be
connected to the GND plane with redundant vias placed to
provide a physically short return path for output currents
flowing back from ground to the VCC pin. High frequency
bypass capacitors should be carefully selected for minimum
inductance and ESR. Parasitic layout inductance should also be
strictly controlled to maximize the effectiveness of the bypass at
high frequencies.
TTL-/CMOS-COMPATIBLE OUTPUT STAGE
Specified propagation delay performance can be achieved only
by keeping the capacitive load at or below the specified minimums. The outputs of the ADCMP608 and ADCMP609 are
designed to directly drive one Schottky TTL or three low power
Schottky TTL loads or equivalent. For large fan outs, buses, or
transmission lines, an appropriate buffer should be used to
maintain the excellent speed and stability of the part.
With the rated 15 pF load capacitance applied, even at 2.5 V
VCC, more than half of the total device propagation delay is
output stage slew time. Because of this, the total prop delay will
decrease as VCCO decreases and instability in the power supply
may show up as excess delay dispersion.
This delay is measured to the 50% point for whatever supply is
in use, so the fastest times will be observed with the VCC supply
at 2.5 V, and larger values will be observed when driving loads,
that switch at other levels. Overdrive and input slew rate
dispersions are not significantly affected by output loading and
VCC variations.
A1
Q1
+IN
–IN
OUTPUT
AV
A2
GAIN STAGE
Q2
OUTPUT STAGE
05918-012
The ADCMP608 and ADCMP609 comparators are high speed
devices. Despite the low noise output stage, it is essential to use
proper high speed design techniques to achieve the specified
performance. Because comparators are uncompensated
amplifiers, feedback in any phase relationship is likely to cause
oscillations or undesired hysteresis. Of critical importance is the
use of low impedance supply planes, particularly the output
supply plane (VCCO) and the ground plane (GND). Individual
supply planes are recommended as part of a multilayer board.
Providing the lowest inductance return path for switching
currents ensures the best possible performance in the target
application.
Figure 13. Simplified Schematic Diagram
of TTL/CMOS-COMPATIBLE Output Stage
USING/DISABLING THE LATCH FEATURE
The latch input of the ADCMP609 is designed for maximum
versatility. It can safely be left floating or pulled to TTL high for
normal comparator operation with no hysteresis, or it can be
driven low by any standard TTL/CMOS device as a high speed
latch.
In addition, the pin can be operated as a hysteresis control pin
with a bias voltage of 1.25 V nominal and an input resistance of
approximately 7000 Ω. This allows the comparator hysteresis to
be easily and accurately controlled by either a resistor or an
inexpensive CMOS DAC.
Hysteresis control and latch mode can be used together if an
open drain, a collector, or a three-state driver is connected in
parallel to the hysteresis control resistor or current source.
Due to the programmable hysteresis feature,the logic threshold
of the latch pin is approximately 1.1 V regardless of VCC.
OPTIMIZING PERFORMANCE
As with any high speed comparator, proper design and layout
techniques are essential for obtaining the specified
performance. Stray capacitance, inductance, common power
and ground impedances, or other layout issues can severely limit
performance and often cause oscillation. The source impedance
should be minimized as much as is practicable. High source
impedance, in combination with the parasitic input capacitance
of the comparator, will cause an undesirable degradation in
bandwidth at the input, thus degrading the overall response.
Higher impedances encourage undesired coupling.
The TTL/CMOS-compatible output stage is shown in the
simplified schematic diagram of Figure 12. Because of its
inherent symmetry and generally good behavior, this output
stage is readily adaptable for driving various filters and other
unusual loads.
Rev. PrA | Page 9 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
COMPARATOR HYSTERESIS
The ADCMP608 and ADCMP609 comparator is designed to
reduce propagation delay dispersion over a wide input overdrive
range of 5 mV to VCCI − 1 V. Propagation delay dispersion is the
variation in propagation delay that results from a change in the
degree of overdrive or slew rate (how far or how fast the input
signal exceeds the switching threshold).
Propagation delay dispersion is a specification that becomes
important in high speed, time-critical applications, such as data
communication, automatic test and measurement, and instrumentation. It is also important in event-driven applications,
such as pulse spectroscopy, nuclear instrumentation, and
medical imaging. Dispersion is defined as the variation in
propagation delay as the input overdrive conditions are changed
(see Figure 14 and Figure 15).
The addition of hysteresis to a comparator is often desirable in a
noisy environment, or when the differential input amplitudes
are relatively small or slow moving. The transfer function for a
comparator with hysteresis is shown in Figure 16. As the input
voltage approaches the threshold (0.0 V, in this example) from
below the threshold region in a positive direction, the
comparator switches from a low to a high when the input crosses
+VH/2. The new switching threshold becomes −VH/2. The
comparator remains in the high state until the threshold −VH/2
is crossed from below the threshold region in a negative
direction. In this manner, noise or feedback output signals
centered on 0.0 V input cannot cause the comparator to switch
states unless it exceeds the region bounded by ±VH/2.
OUTPUT
VOH
ADCMP608 and ADCMP609 dispersion is typically <5 ns as
the overdrive varies from 5 mV to 500 mV, and the input slew
rate varies from 2 V/ns to 10 V/ns. This specification applies to
both positive and negative signals because the device has very
closely matched delays for both positive-going and negativegoing inputs, and very low output skews. Remember to add the
actual device offset to the overdrive for repeatable dispersion
measurements.
VOL
–VH
2
500mV OVERDRIVE
0
+VH
2
INPUT
05918-015
COMPARATOR PROPAGATION
DELAY DISPERSION
Figure 16. Comparator Hysteresis Transfer Function
INPUT VOLTAGE
10mV OVERDRIVE
DISPERSION
Q/Q OUTPUT
05918-013
VN ± VOS
Figure 14. Propagation Delay—Overdrive Dispersion
INPUT VOLTAGE
1V/ns
VN ± VOS
DISPERSION
Q/Q OUTPUT
05918-014
10V/ns
The customary technique for introducing hysteresis into a
comparator uses positive feedback from the output back to the
input. One limitation of this approach is that the amount of
hysteresis varies with the output logic levels, resulting in
hysteresis that is not symmetric about the threshold. The
external feedback network can also introduce significant
parasitics that reduce high speed performance, and can even
induce oscillation in some cases.
The ADCMP609 comparator offers a programmable hysteresis
feature that significantly improves accuracy and stability.
Connecting an external pull-down resistor or a current source
from the LE/HYS pin to GND, varies the amount of hysteresis
in a predictable and stable manner. Leaving the LE/HYS pin
disconnected or driving it high removes the hysteresis. The
maximum hysteresis that can be applied using this pin is
approximately 160 mV. Figure 17 illustrates the amount of
hysteresis applied as a function of external resistor value.
Figure TBD illustrates hysteresis as a function of current.
Figure 15. Propagation Delay—Slew Rate Dispersion
Rev. PrA | Page 10 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
The hysteresis control pin appears as a 1.25 V bias voltage seen
through a series resistance of 7k ± 20% throughout the
hysterisis control range. The advantages of applying hysteresis
in this manner are improved accuracy, improved stability,
reduced component count, and maximum versatility. An
external bypass capacitor is not recommended on the HYS pin
because it would likely degrade the jitter performance of the
device and impair the latch function. As described in
Using/Disabling the Latch Feature, hysteresis control need not
compromise the latch function.
CROSSOVER BIAS POINT
Rail-to-rail inputs of this type, in both op amps and comparators have a dual front-end design. Certain devices are active
near the VCC rail and others are active near the VEE rail. At some
predetermined point in the common-mode range, a crossover
occurs. At this point, normally VCC/2, the direction of the bias
current reverses and there are changes in measured offset
voltages and currents.
With VCC less than 4 V, this crossover is at the expected VCC/2,
but with VCC greater than 4 V, the crossover point instead
follows VCC 1:1, bringing it to approximately 3 V with VCC at
5 V. This means that the comparator input characteristics will
more closely resemble the inputs of non rail-to rail ground
sensing comparators such as the AD8611.
MINIMUM INPUT SLEW RATE REQUIREMENT
(Remove if device is stable.)
Figure 17. Hysteresis vs. RHYS Control Resistor
As with most high speed comparators, without hysteresis a
minimum slew rate must be met to ensure that the device does
not oscillate as the input signal crosses the threshold. This
oscillation is due to the high gain bandwidth of the comparator
in combination with feedback parasitics inherent in the package
and PC board. A minimum slew rate of TBD. V/μs ensures
clean output transitions from the ADCMP608/ADCMP609
comparators without hysteresis. In many applications,
chattering is not harmful.
Rev. PrA | Page 11 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
TYPICAL APPLICATION CIRCUITS
2.5V
ADCMP608
INPUT
1.25V
±50mV
INPUT
1.25V
REF
2.5V TO 5V
CMOS
PWM
OUTPUT
10kΩ
10kΩ
0.1µF
ADCMP609
ADCMP608
OUTPUT
10kΩ
LE/HYS
220pF
0.1µF
100kΩ
Figure 18. Self-Biased 50% Slicer
05918-020
2kΩ
2kΩ
05918-017
INPUT
Figure 21. Oscillator and Pulse Width Modulator
5V
10kΩ
INPUT
CMOS
VDD
2.5V TO 5V
ADCMP609
VREF
10kΩ
0.1µF
ADCMP608
–
LE/HYS
OUTPUT
05918-021
100Ω
+
OUTPUT
05918-018
LVDS
0.02µF
Figure 19. LVDS to CMOS Receiver
Figure 22. Duty Cycle to Differential Voltage
5V
2.5V TO 5V
20kΩ
39kΩ
ADCMP609
CONTROL
VOLTAGE
0V TO 2.5V
470pF
150kΩ
LE/HYS
150kΩ
DIGITAL
INPUT
05918-019
39kΩ
OUTPUT
HYSTERESIS
CURRENT
74AHC
1G07
LE/HYS
10kΩ
Figure 23. DAC Hysteresis Adjustment with Latch
Figure 20. Voltage Controlled Oscillator
Rev. PrA | Page 12 of 16
05918-022
ADCMP609
ADCMP608/ADCMP609
Preliminary Technical Data
TIMING INFORMATION
Figure 24 illustrates the ADCMP608/ADCMP609 latch timing relationships. Table 6 provides definitions of the terms found in the figure.
1.1V
LATCH ENABLE
tS
tPL
tH
DIFFERENTIAL
INPUT VOLTAGE
VIN
VN ± VOS
VOD
tPDL
tPLOH
Q OUTPUT
50%
tF
tPDH
tPLOL
tR
05918-023
50%
Q OUTPUT
Figure 24. System Timing Diagram
Table 6. Timing Descriptions
Symbol
tPDH
tPDL
tPLOH
tPLOL
tH
tPL
Timing
Input to output high
delay
Input to output low
delay
Latch enable to output
high delay
Latch enable to output
low delay
Minimum hold time
tS
Minimum latch enable
pulse width
Minimum setup time
tR
Output rise time
tF
Output fall time
VOD
Voltage overdrive
Description
Propagation delay measured from the time the input signal crosses the reference (± the input offset
voltage) to the 50% point of an output low-to-high transition.
Propagation delay measured from the time the input signal crosses the reference (± the input offset
voltage) to the 50% point of an output high-to-low transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high transition to
the 50% point of an output low-to-high transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high transition to
the 50% point of an output high-to-low transition.
Minimum time after the negative transition of the latch enable signal that the input signal must
remain unchanged to be acquired and held at the outputs.
Minimum time that the latch enable signal must be high to acquire an input signal change.
Minimum time before the negative transition of the latch enable signal occurs that an input signal
change must be present to be acquired and held at the outputs.
Amount of time required to transition from a low to a high output as measured at the 20% and 80%
points.
Amount of time required to transition from a high to a low output as measured at the 20% and 80%
points.
Difference between the input voltages VA and VB.
Rev. PrA | Page 13 of 16
ADCMP608/ACMP609
Preliminary Technical Data
NOTES
Rev. PrA | Page 14 of 16
ADCMP608/ADCMP609
Preliminary Technical Data
NOTES
Rev. PrA | Page 15 of 16
ADCMP608/ACMP609
Preliminary Technical Data
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR05918-0-2/06(PrA)
Rev. PrA | Page 16 of 16