AD AD7805CR

a
+3.3 V to +5 V Quad/Octal 10-Bit DACs
AD7804/AD7805/AD7808/AD7809*
FUNCTIONAL BLOCK DIAGRAMS
FEATURES
Four 10-Bit DACs in One Package
Serial and Parallel Loading Facilities Available
AD7804 Quad 10-Bit Serial Loading
AD7805 Quad 10-Bit Parallel Loading
AD7808 Octal 10-Bit Serial Loading
AD7809 Octal 10-Bit Parallel Loading
+3.3 V to +5 V Operation
Power-Down Mode
Power-On Reset
Standby Mode (All DACs/Individual DACs)
Low Power All CMOS Construction
10-Bit Resolution
Double Buffered DAC Registers
Dual External Reference Capability
AVDD DVDD
REFOUT
1.23V REF
AGND DGND
VOUTF*
POWER ON
RESET
AD7804/
AD7808
REFIN
AVDD
DIVIDER
MUX
VBIAS
DAC D
COMP
CHANNEL D
CONTROL REG
DATA
REGISTER
MUX
CHANNEL C
CONTROL REG
CHANNEL B
CONTROL REG
VBIAS
DAC C
DATA
REGISTER
PD**
CHANNEL A
CONTROL REG
DAC B
DATA
REGISTER
DAC
REGISTER
VBIAS
DAC A
The AD7804/AD7808 are quad/octal 10-bit digital-to-analog
converters, with serial load capabilities, while the AD7805/AD7809
are quad/octal 10-bit digital-to-analog converters with parallel
load capabilities. These parts operate from a +3.3 V to +5 V
(±10%) power supply and incorporates an on-chip reference.
These DACs provide output signals in the form of VBIAS ± VSWING.
VSWING is derived internally from VBIAS. On-chip control registers
include a system control register and channel control registers.
The system control register has control over all DACs in the
package. The channel control registers allow individual control
of DACs. The complete transfer function of each individual
DAC can be shifted around the VBIAS point using an on-chip
Sub DAC. All DACs contain double buffered data inputs,
which allow all analog outputs to be simultaneously updated
using the asynchronous LDAC input.
FSIN
CLKIN
SDIN
Channels Controlled
Main DAC
Sub DAC
Hardware Clear
System Control
Power Down1
System Standby2
System Clear
Input Coding
Channel Control
Channel Standby2
Channel Clear
VBIAS
All
兹
兹
All
All
All
All
兹
兹
兹
兹
兹
兹
Selective
Selective
Selective
兹
兹
兹
兹
兹
VOUTA
VOUTH*
VOUTG*
INPUT SHIFT
REGISTER &
CONTROL LOGIC
CLR LDAC
**ONLY AD7804 SHOWN FOR CLARITY
**SHOWS ADDITIONAL CHANNELS ON THE AD7808
**PIN ON THE AD7808 ONLY
AVDD DVDD
REFOUT
1.23V REF
AGND DGND
VOUTF*
POWER ON
RESET
AD7805/
AD7809
REFIN
AVDD
DIVIDER
MUX
VBIAS
DAC D
VOUTE*
VOUTD
COMP
CHANNEL D
CONTROL REG
DATA
REGISTER
MUX
CHANNEL C
CONTROL REG
DAC
REGISTER
VBIAS
DAC C
DATA
REGISTER
CHANNEL B
CONTROL REG
DAC B
DATA
REGISTER
VOUTC
DAC
REGISTER
VBIAS
MUX
Control Features
VOUTB
DAC
REGISTER
DATA
REGISTER
SYSTEM
CONTROL REG
GENERAL DESCRIPTION
VOUTC
DAC
REGISTER
MUX
MUX
VOUTD
DAC
REGISTER
VBIAS
APPLICATIONS
Optical Disk Drives
Instrumentation and Communication Systems
Process Control and Voltage Setpoint Control
Trim Potentiometer Replacement
Automatic Calibration
VOUTE*
VOUTB
DAC
REGISTER
VBIAS
PD**
CHANNEL A
CONTROL REG
MUX
DAC A
DATA
REGISTER
DAC
REGISTER
SYSTEM
CONTROL REG
CS
WR
CONTROL
LOGIC
VOUTA
VOUTH*
INPUT
REGISTER
VOUTG*
兹
NOTES
1
Power-down function powers down all internal circuitry including the reference.
2
Standby functions power down all circuitry except for the reference.
MODE A0 A1 A2**
DB9 DB2 DB1 DB0
CLR LDAC
**ONLY AD7805 SHOWN FOR CLARITY
**SHOWS ADDITIONAL CHANNELS ON THE AD7809
**PIN ON THE AD7809 ONLY
REV. A
*Patent pending.
Index on Page 26.
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1998
AD7804/AD7805/AD7808/AD7809
AD7804/AD7805–SPECIFICATIONS
(AVDD and DV DD = 3.3 V ⴞ 10% to 5 V ⴞ 10%; AGND = DGND = 0 V;
Reference = Internal Reference; CL = 100 pF; RL = 2 k⍀ to GND. Sub DAC at Midscale. All specifications TMIN to TMAX unless otherwise noted.)
B Grade1
C Grade1
Units
Comments
10
±3
±3
–80/+40
–V BIAS
/ +40
16
9
2
10
±3
±3
–80/+40
–V BIAS
/ +40
16
10
2
Bits
LSB max
% FSR max
mV max
mV max
DAC Code = 0.5 Full Scale
DAC Code = 000H for Offset Binary
8
± 0.125
± 0.5
8
± 0.125
± 0.5
Bits
LSB typ
LSB max
VBIAS ± 15/16 × VBIAS
VBIAS /16 to 31/16 × VBIAS
4
2.5
1
0.5
0.5
± 0.2
2
0.002
VBIAS ± 15/16 × VBIAS
VBIAS/16 to 31/16 × VBIAS
4
2.5
1
0.5
0.5
± 0.2
2
0.002
V
V
µs max
V/µs typ
nV-s typ
nV-s typ
nV-s typ
LSB typ
Ω typ
%/% typ
DAC REFERENCE INPUTS
REF IN Range
REF IN Input Leakage
1.0 to VDD/2
±1
1.0 to VDD/2
±1
V min to V max
µA max
DIGITAL INPUTS
Input High Voltage, VIH @ VDD = 5 V
Input High Voltage, VIH @ VDD = 3.3 V
Input Low Voltage, VIL @ VDD = 5 V
Input Low Voltage, VIL @ VDD = 3.3 V
Input Leakage Current
Input Capacitance
Input Coding
2.4
2.1
0.8
0.6
± 10
10
Twos Comp/Binary
2.4
2.1
0.8
0.6
µA max
10
Twos Comp/Binary
V min
V min
V max
V max
REFERENCE OUTPUT
REF OUT Output Voltage
REF OUT Error
REF OUT Temperature Coefficient
REF OUT Output Impedance
1.23
±8
–100
5
1.23
±8
–100
5
V nom
% max
ppm/°C typ
kΩ nom
3/5.5
3/5.5
V min to V max
12
250
12
250
mA max
µA
0.8
1.5
0.8
1.5
µA max
µA max
66
1.38
66
1.38
mW max
mW max
4.4
8.25
4.4
8.25
µW max
µW max
Parameter
STATIC PERFORMANCE
MAIN DAC
Resolution
Relative Accuracy
Gain Error
Bias Offset Error2
Zero-Scale Error3
Monotonicity
Minimum Load Resistance
SUB DAC
Resolution
Differential Nonlinearity
OUTPUT CHARACTERISTICS
Output Voltage Range3
Voltage Output Settling Time to 10 Bits
Slew Rate
Digital-to-Analog Glitch Impulse
Digital Feedthrough
Digital Crosstalk
Analog Crosstalk
DC Output Impedance
Power Supply Rejection Ratio
POWER REQUIREMENTS
VDD (AVDD and DVDD)
IDD (AIDD Plus DIDD)
Normal Mode
System Standby (SSTBY) Mode
Power-Down (PD) Mode
@ +25°C
TMIN–TMAX
Power Dissipation
Normal Mode
System Standby (SSTBY) Mode
Power-Down (PD) Mode
@ +25°C
TMIN–TMAX
Bits
kΩ min
and 200H for Twos Complement Coding
Refers to an LSB of the Main DAC
Twos Complement Coding
Offset Binary Coding
Typically 1.5 µs
1 LSB Change Around the Major Carry
∆VDD ± 10%
Typically ± 1 nA
pF max
Excluding Load Currents
VIH = V DD, V IL = DGND
VIH = V DD, V IL = DGND
VIH = V DD, V IL = DGND
Excluding Power Dissipated in Load
NOTES
1
Temperature range is – 40°C to +85°C.
2
Can be minimized using the Sub DAC.
3
VBIAS is the center of the output voltage swing and can be V DD/2, Internal Reference or REFIN as determined by MX1 and MX0 in the channel control register.
Specifications subject to change without notice.
–2–
REV. A
AD7804/AD7805/AD7808/AD7809
AD7808/AD7809–SPECIFICATIONS
(AVDD and DV DD = 3.3 V ⴞ 10% to 5 V ⴞ 10%; AGND = DGND = 0 V;
Reference = Internal Reference; CL = 100 pF; RL = 2 k⍀ to GND. Sub DAC at Midscale. All specifications TMIN to TMAX unless otherwise noted.)
B Grade1
Units
Comments
10
±4
±3
± 60
± 35
9
2
Bits
LSB max
% FSR max
mV max
mV max
Bits
kΩ min
DAC Code = 0.5 Full Scale
DAC Code = 000H for Offset Binary
and 200H for Twos Complement
Coding
8
± 0.125
± 0.5
Bits
LSB typ
LSB max
VBIAS ± 15/16 × VBIAS
VBIAS /16 to 31/16 × VBIAS
4
2.5
1
0.5
0.5
± 0.2
2
0.002
V
V
µs max
V/µs typ
nV-s typ
nV-s typ
nV-s typ
LSB typ
Ω typ
%/% typ
DAC REFERENCE INPUTS
REF IN Range
REF IN Input Leakage
1.0 to VDD/2
±1
V min to V max
µA max
DIGITAL INPUTS
Input High Voltage, VIH @ VDD = 5 V
Input High Voltage, VIH @ VDD = 3.3 V
Input Low Voltage, VIL @ VDD = 5 V
Input Low Voltage, VIL @ VDD = 3.3 V
Input Leakage Current
Input Capacitance
Input Coding
2.4
2.1
0.8
0.6
± 10
8
Twos Comp/Binary
V min
V min
V max
V max
µA max
pF max
REFERENCE OUTPUT
REF OUT Output Voltage
REF OUT Error
REF OUT Temperature Coefficient
REF OUT Output Impedance
1.23
±8
–100
5
V nom
% max
ppm/°C typ
kΩ nom
3/5.5
V min to V max
18
250
mA max
µA max
1
3
µA max
µA max
99
1.38
mW max
mW max
5.5
16.5
µW max
µW max
Parameter
STATIC PERFORMANCE
MAIN DAC
Resolution
Relative Accuracy
Gain Error
Bias Offset Error2
Zero-Scale Error
Monotonicity
Minimum Load Resistance
SUB DAC
Resolution
Differential Nonlinearity
OUTPUT CHARACTERISTICS
Output Voltage Range3
Voltage Output Settling Time to 10 Bits
Slew Rate
Digital-to-Analog Glitch Impulse
Digital Feedthrough
Digital Crosstalk
Analog Crosstalk
DC Output Impedance
Power Supply Rejection Ratio
POWER REQUIREMENTS
VDD (AVDD and DVDD)
IDD (AIDD Plus DIDD)
Normal Mode
System Standby (SSTBY) Mode
Power-Down (PD) Mode
@ +25°C
TMIN–TMAX
Power Dissipation
Normal Mode
System Standby (SSTBY) Mode
Power-Down (PD) Mode
@ +25°C
TMIN–TMAX
Refers to an LSB of the Main DAC
Twos Complement Coding
Offset Binary Coding
Typically 1.5 µs
1 LSB Change Around the Major Carry
∆VDD ± 10%
Typically ± 1 nA
Excluding Load Currents
VIH = V DD, V IL = DGND
VIH = VDD , VIL = DGND
VIH = V DD, V IL = DGND
Excluding Power Dissipated in Load
NOTES
1
Temperature range is – 40°C to +85°C.
2
Can be minimized using the Sub DAC.
3
VBIAS is the center of the output voltage swing and can be V DD/2, Internal Reference or REFIN as determined by MX1 and MX0 in the channel control register.
Specifications subject to change without notice.
REV. A
–3–
AD7804/AD7805/AD7808/AD7809
AD7804/AD7808 TIMING CHARACTERISTICS1(V
DD =
3.3 V ⴞ 10% to 5 V ⴞ 10%; AGND = DGND = 0 V; Reference =
Internal Reference. All specifications TMIN to TMAX unless otherwise noted.)
Parameter
t1
t2
t3
t4
t5
t6
t6A
t7
t8
t9
Limit at TMIN, T MAX
All Versions
Units
Description
100
40
40
30
30
5
6
90
20
40
100
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns max
ns min
ns min
ns min
CLKIN Cycle Time
CLKIN High Time
CLKIN Low Time
FSIN Setup Time
Data Setup Time
Data Hold Time
LDAC Hold Time
FSIN Hold Time
LDAC, CLR Pulsewidth
LDAC Setup Time
NOTES
1
Sample tested during initial release and after any redesign or process change that may affect this parameter. All input signals are specified with tr = tf = 5 ns and
timed from a voltage of (V IL + VIH)/2.
Specifications subject to change without notice.
t1
CLKIN(I)
t2
t3
t4
t7
FSIN(I)
t5
t6
SDIN(I)
DB15
DB0
t 6A
t5
LDAC1
t9
LDAC2
t8
t8
CLR
1TIMING
2TIMING
REQUIREMENTS FOR SYNCHRONOUS LDAC UPDATE OR LDAC MAY BE TIED PERMANENTLY LOW IF REQUIRED.
REQUIREMENTS FOR ASYNCHRONOUS LDAC UPDATE.
Figure 1. Timing Diagram for AD7804 and AD7808
–4–
REV. A
AD7804/AD7805/AD7808/AD7809
AD7805/AD7809 TIMING CHARACTERISTICS1
(VDD = 3.3 V ⴞ 10% to 5 V ⴞ 10%; AGND = DGND = 0 V; Reference
= Internal Reference. All specifications TMIN to TMAX unless otherwise noted.)
Parameter
Limit at TMIN, T MAX
All Versions
Unit
Description
t1
t2
t3
t4
t5
t6
t6A
t7
t8
t9
t10
t11
t12
25
4.5
25
4.5
25
4.5
6
40
0
40
100
40
100
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
Mode Valid to Write Setup Time
Mode Valid to Write Hold Time
Address Valid to Write Setup Time
Address Valid to Write Hold Time
Data Setup Time
Data Hold Time
LDAC Valid to Write Hold Time
Chip Select to Write Setup Time
Chip Select to Write Hold Time
Write Pulsewidth
Time Between Successive Writes
LDAC, CLR Pulsewidth
Write to LDAC Setup Time
NOTE
1
Sample tested during initial release and after any redesign or process change that may affect this parameter. All input signals are specified with tr = tf = 5 ns and
timed from a voltage of (V IL + VIH)/2.
Specifications subject to change without notice.
t1
t2
MODE
t3
t4
A0, A1, A2
t8
t7
CS
t10
t9
WR
t5
t6
DATA
t 6A
LDAC 1
t12
t11
LDAC 2
t11
CLR
1TIMING
2TIMING
REQUIREMENTS FOR SYNCHRONOUS LDAC UPDATE OR LDAC MAY BE TIED PERMANENTLY LOW IF REQUIRED.
REQUIREMENTS FOR ASYNCHRONOUS LDAC UPDATE.
Figure 2. Timing Diagram for AD7805/AD7809 Parallel Write
REV. A
–5–
AD7804/AD7805/AD7808/AD7809
ABSOLUTE MAXIMUM RATINGS 1
PDIP (N-24) Package, Power Dissipation . . . . . . . . . 670 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 105°C/W
Lead Temperature, Soldering (10 sec) . . . . . . . . . . . +260°C
SOIC (R-28) Package, Power Dissipation . . . . . . . . . 875 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 70°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
PDIP (N-28) Package, Power Dissipation . . . . . . . . . 875 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 75°C/W
Lead Temperature, Soldering (10 sec) . . . . . . . . . . . +260°C
SSOP (RS-28) Package, Power Dissipation . . . . . . . . 875 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 110°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
TQFP (ST-44B) Package, Power Dissipation . . . . . . 450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 116°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
(TA = +25°C unless otherwise noted)
DVDD to DGND . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
AVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V + 0.3 V
Digital Input Voltage to DGND . . . . . –0.3 V to DVDD + 0.3 V
Analog Input Voltage to AGND . . . . . –0.3 V to AVDD + 0.3 V
COMP to AGND . . . . . . . . . . . . . . . –0.3 V to AVDD + 0.3 V
REF OUT to AGND . . . . . . . . . . . . . . . . . . –0.3 V to + AVDD
REF IN to AGND . . . . . . . . . . . . . . . –0.3 V to AVDD + 0.3 V
VOUT to AGND2 . . . . . . . . . . . . . . . . –0.3 V to AVDD + 0.3 V
Input Current to Any Pin Except Supplies3 . . . . . . . . ± 10 mA
Operating Temperature Range
AD7804/AD7805 Commercial Plastic
(B, C Versions) . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
AD7808/AD7809 Commercial Plastic
(B, C Versions) . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
SOIC (R-16) Package, Power Dissipation . . . . . . . . . 450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 75°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
PDIP (N-16) Package, Power Dissipation . . . . . . . . . 670 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 116°C/W
Lead Temperature, Soldering (10 sec) . . . . . . . . . . . +260°C
SOIC (R-24) Package, Power Dissipation . . . . . . . . . 450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 75°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
The outputs may be shorted to voltages in this range provided the power dissipation
of the package is not exceeded.
3
Transient currents of up to 100 mA will not cause SCR latch-up.
ORDERING GUIDE
Model
AD7804BN
AD7804BR
AD7805BN
AD7805BR
AD7805BRS
AD7805CR
AD7808BN
AD7808BR
AD7809BST
Supply
Voltage
3.3 V to 5 V
3.3 V to 5 V
3.3 V to 5 V
3.3 V to 5 V
3.3 V to 5 V
3.3 V to 5 V
3.3 V to 5 V
3.3 V to 5 V
3.3 V to 5 V
Temperature
Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Relative
Accuracy
± 3 LSB
± 3 LSB
± 3 LSB
± 3 LSB
± 3 LSB
± 3 LSB
± 4 LSB
± 4 LSB
± 4 LSB
Package Descriptions
16-Lead Plastic DIP
16-Lead Small Outline IC
28-Lead Plastic DIP
28 Lead Small Outline IC
28-Lead Shrink Small Outline Package
28-Lead Small Outline IC
24-Lead Plastic DIP
24 Lead Small Outline IC
44-Lead Thin Plastic Quad Flatpack (TQFP)
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although these devices feature proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–6–
Package
Options
N-16
R-16
N-28
R-28
RS-28
R-28
N-24
R-24
ST-44B
WARNING!
ESD SENSITIVE DEVICE
REV. A
AD7804/AD7805/AD7808/AD7809
AD7804/AD7808 PIN FUNCTION DESCRIPTION
AD7804
Pin No.
AD7808
Pin No.
Mnemonic
Description
1
2, 3
4
1, 6
2, 3
4
5
AGND
VOUTB, VOUTA
REFOUT
PD
5
7, 8
9
VOUTF, VOUTE
FSIN
6
10
LDAC
7
11
SDIN
8
9
10
12
13
14
DGND
DVDD
CLKIN
11
15
CLR
12
16
17, 18
20
NC
VOUTH, VOUTG
REFIN
13
21
COMP
14, 15
16
22, 23
19, 24
VOUTD, V OUTC
AVDD
Ground reference point for analog circuitry.
Analog output voltage from the DACs.
Reference Output. This is a bandgap reference and is typically 1.23 V.
Active low input used to put the part into low power mode reducing current consumption
to 1 µA.
Analog output voltages from the DACs.
Level-triggered control input (active low). This is the frame synchronization signal for the
input data. When FSIN goes low, it enables the input shift register and data is transferred
on the falling edges of CLKIN.
LDAC Input. When this digital input is taken low, all DAC registers are simultaneously
updated with the contents of the data registers. If LDAC is tied permanently low, or is
low on the sixteenth falling clock edge with timing similar to that of SDIN, an automatic
update will take place.
Serial Data Input. These devices accept a 16-bit word. Data is clocked into the input shift
register on the falling edge of CLKIN.
Ground reference point for digital circuitry.
Digital Power Supply.
Clock Input. Data is clocked into the input shift register on the falling edges of CLKIN.
Duty Cycle should be between 40% and 60%.
Asynchronous CLR Input. When this input is taken low, all Main DAC outputs are
cleared either to VBIAS or to V BIAS/16 volts. All Sub DACs are also cleared and thus the
transfer function of the Main DAC will remain centered around the VBIAS point.
No Connect. This pin should be left open circuit.
Analog output voltages from the DACs.
This is an external reference input for the DACs. When this reference is selected for a
DAC in the control register, the analog output from the selected DAC swings around this
point.
Compensation Pin. This pin provides an output from the internal VDD/2 divider and is
provided for ac bypass purposes only. This pin should be decoupled with 1 nF capacitors
to both AVDD and AGND. This pin can be overdriven with an external reference, thus
giving the facility for two external references on the part.
Analog output voltage from the DACs.
Analog Power Supply. +3.3 V to +5 V.
AD7808 PIN CONFIGURATION
AD7804 PIN CONFIGURATION
AGND 1
VOUT B 2
VOUT A 3
16
15
14
AVDD
VOUT C
VOUT D
AD7804 13 COMP
TOP VIEW
FSIN 5 (Not to Scale) 12 REFIN
REFOUT 4
LDAC 6
11
CLR
SDIN 7
10
CLKIN
DGND 8
9
DVDD
AGND
1
24
AVDD
VOUT B
2
23
VOUT C
VOUT A
3
22
VOUT D
REFOUT
4
21
COMP
PD
5
AGND
6
VOUT F
7
VOUT E
8
17
VOUT H
FSIN
9
16
NC
LDAC 10
15
CLR
SDIN 11
14
CLKIN
DGND 12
13
DVDD
AD7808
20
REFIN
19
AVDD
TOP VIEW
(Not to Scale) 18 V
OUT G
NC = NO CONNECT
REV. A
–7–
AD7804/AD7805/AD7808/AD7809
AD7805/AD7809 PIN FUNCTION DESCRIPTIONS
AD7805
Pin No.
AD7809
Pin No.
1
2, 3
4
5–10,
12, 13
19, 20
1, 11, 13,
20, 33
2, 5, 39, 40
41, 42
43
3, 4, 6, 7, 9,
10, 15, 23
24, 26
11
8, 12
14
VOUTF, VOUTE
LDAC
14
15
16
16
17
18
DGND
DVDD
WR
17
18
21
19
CS
CLR
21, 22
22, 25
27, 29, 30
VOUTH, VOUTG
A2, A1, A0
23
31
MODE
24
32
REFIN
25
34
COMP
26, 27
28
35, 36
28, 37, 38
44
VOUTD, V OUTC
AVDD
PD
Mnemonic
Description
NC
No Connect. These pins should be left open circuit.
AGND
VOUTB, VOUTA
REFOUT
DB9–DB2
Ground reference point for analog circuitry.
Analog output voltages from the DACs.
Reference Output. This is a bandgap reference and is typically 1.23 V.
Data Inputs. DB9 to DB2 are the 8 MSBs of the data word.
DB1, DB0
DB1 and DB0 function as the 2 LSBs of the 10-bit word in 10-bit parallel mode but
have other functions when BYTE loading structure is used.
Analog output voltages from the DACs.
LDAC Input. When this digital input is taken low, all DAC registers are simultaneously
updated with the contents of the DAC data registers. If LDAC is permanently tied low, or is
low during the rising edge of WR similar to data inputs, an automatic update will take place.
Ground reference point for digital circuitry.
Digital Power Supply.
Write Input WR is an active low logic input which is used in conjunction with CS and
the address pins to write data to the relevant registers.
Chip Select. Active low logic input.
Asynchronous CLR Input. When this input is taken low, all Main DAC outputs are
cleared either to VBIAS or to V BIAS/16 volts. All Sub DACs are also cleared and thus the
transfer function of the MAIN DAC will remain centered around the VBIAS point.
Analog output voltages from the DACs.
DAC Address Inputs. These digital inputs are used in conjunction with CS and WR to
determine which DAC channel control register or DAC data register is loaded from the
input register. These address bits are don’t cares when writing to the system control register.
Logic Input. Logic high enables writing to the DAC data registers, a logic low enables
writing to the control registers.
This is an external reference input for the DAC. When this reference is selected for the DAC
in the control register, the analog output from the selected DAC swings around this point.
Compensation Pin. This pin provides an output from the internal VDD/2 divider and is
provided for ac bypass purposes only. This pin should be decoupled with 1 nF capacitors
to both AVDD and AGND. This pin can be overdriven with an external reference, thus
giving the facility for two external references on the part.
Analog output voltages from the DACs.
Analog Power Supply.
Active low input used to put the part into low power mode reducing current consumption to 1 µA.
VOUT C
VOUT A 3
26
VOUT D
REFOUT 4
25
COMP
DB9 5
24
REFIN
NC 1
AGND 2
23
MODE
22
A0
TOP VIEW
DB6 8 (Not to Scale) 21 A1
DB0
DB4 10
19
DB1
LDAC 11
18
CLR
DB3 12
17
CS
DB2 13
16
WR
DGND 14
15
DVDD
31
MODE
DB8 4
AGND 5
30
A0
A1
28 AVDD
29
AD7809
DB7 6
TOP VIEW
(Not to Scale)
DB6 7
VOUTF 8
27
26
A2
DB0
DB5 9
25
VOUTG
DB4 10
24
DB1
NC 11
23
DB2
12 13 14 15 16 17 18 19 20 21 22
NC = NO CONNECT
–8–
CS
VOUT H
20
DB9 3
WR
CLR
NC
DB5 9
NC
REFIN
DGND
DVDD
AD7805
32
33
PIN 1
IDENTIFIER
LDAC
DB3
DB7 7
44 43 42 41 40 39 38 37 36 35 34
VOUT E
NC
DB8 6
COMP
AVDD
27
AVDD
VOUT C
VOUT D
28
AGND
AVDD
AGND 1
VOUT B 2
VOUT A
VOUT B
AGND
AD7809 PIN CONFIGURATION
PD
REFOUT
AD7805 PIN CONFIGURATION
REV. A
AD7804/AD7805/AD7808/AD7809
TERMINOLOGY
Relative Accuracy
Digital-to-Analog Glitch Impulse
Digital-to-analog glitch impulse is the impulse injected into the
analog output when the digital inputs change state with the
DAC selected and the LDAC used to update the DAC. It is
normally specified as the area of the glitch in nV-s and is measured when the digital input code is changed by 1 LSB at the
major carry transition. Regardless of whether offset binary or twos
complement coding is used, the major carry transition occurs at
the analog output voltage change of VBIAS to VBIAS – 1 LSB
or vice versa.
For the DACs, relative accuracy or endpoint nonlinearity is a
measure of the maximum deviation, in LSBs, from a straight
line passing through the endpoints of the DAC transfer function. Figures 32 and 33 show the linearity at 3 V and 5 V
respectively.
Differential Nonlinearity
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of ±1 LSB maximum ensures monotonicity.
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into
the analog output of a DAC from the digital inputs of the same
DAC but is measured when the DAC is not updated. It is specified in nV secs and is measured with a full-scale code change on
the data bus, i.e., from all 0s to all 1s and vice versa.
Bias Offset Error
If the DACs are ideal, the output voltage of any DAC with
midscale code loaded will be equal to VBIAS where VBIAS is selected by MX1 and MX0 in the control register. The DAC bias
offset error is the difference between the actual output voltage
and VBIAS, expressed in mV.
Digital Crosstalk
Digital crosstalk is the glitch impulse transferred to the output
of one converter due to a digital code change to another DAC.
It is specified in nV-s.
Gain Error
The difference between the actual and ideal analog output
range, expressed as a percent of full-scale range. It is the deviation in slope of the DAC transfer characteristic from ideal.
Analog Crosstalk
Analog crosstalk is a change in output of any DAC in response
to a change in the output of one or more of the other DACs. It
is measured in LSBs.
Zero-Scale Error
The zero-scale error is the actual output minus the ideal output
from any DAC when zero code is loaded to the DAC. If offset
binary coding is used, the code loaded is 000Hex, and if twos
complement coding is used, a code of 200HEX is loaded to the
DAC to calculate the zero-scale error. Zero-scale error is expressed in mV.
Power Supply Rejection Ratio (PSRR)
This specification indicates how the output of the DAC is affected by changes in the power supply voltage. Power-supply
rejection ratio is quoted in terms of % change in output per %
change in VDD for full-scale output of the DAC. VDD is varied
± 10%.
AD7804/AD7808 INTERFACE SECTION
sequence for the channel control register write, and Figures 6
and 7 show the sequence for loading data to the Main and Sub
DAC data registers. Figure 3 shows the internal registers associated with the AD7804/AD7808 serial interface DACs. Only one
DAC structure is shown for clarity.
The AD7804 and AD7808 are serial input devices. Three lines
control the serial interface, FSIN, CLKIN and SDIN. The timing
diagram is shown in Figure 1.
Two mode bits (MD1 and MD0) which are DB13 and DB14 of
the serial word written to the AD7804/AD7808 are used to determine whether writing is to the DAC data registers or the control
registers of the device. These parts contain a system control
register for controlling the operation of all DACs in the package
as well as a channel control register for controlling the operation of
each individual DAC. Table I shows how to access these registers.
FSIN
CLKIN
SDIN
16-BIT
INPUT SHIFT REGISTER
DECODER
SYSTEM
CONTROL
REGISTER
Table I. Register Selection Table for the AD7804/AD7808
MD1
MD0
Function
0
0
1
0
1
X
Write enable to system control register.
Write enable to channel control register.
Write enable to DAC data registers.
TO ALL
CHANNELS
SINGLE
CHANNEL
INTERNAL VREF
VDD/2
DATA REGISTER
DATA REGISTER
10
8
DAC REGISTER
DAC REGISTER
10
10-BIT DAC
(MAIN DAC)
VOUT
When the FSIN input goes low, data appearing on the SDIN
line is clocked into the input register on each falling edge of
CLKIN. Data to be transferred to the AD7804/AD7808 is
loaded MSB first. Figure 4 shows the loading sequence for the
AD7804/AD7808 system control register, Figure 5 shows the
REV. A
CHANNEL
CONTROL
REGISTER
8
8-BIT DAC
(SUB DAC)
VBIAS
MUX
REFIN
Figure 3. AD7804/AD7808 Internal Registers
–9–
AD7804/AD7805/AD7808/AD7809
MSB
X
LSB
MD0 = 0
MD1 = 0
X
X
X
X
X
0
PD
BIN/COMP
SSTBY
SCLR
0
X
X
X = Don’t Care
Figure 4. AD7804/AD7808 System Control Register Loading Sequence
DB15 (MSB)
X
DB0 (LSB)
MD0 = 1
MD1 = 0
A2*
A1
A0
MX1
MX0
X
X
STBY
X
CLR
0
X
X
X = Don’t Care
*Applicable to the AD7808 Only, and Are Don’t Care Conditions when Operating the AD7804 .
Figure 5. AD7804/AD7808 Channel Control Register Loading Sequence
DB15 (MSB)
MAIN/SUB
DB0 (LSB)
MD0 = X MD1 = 1 A2* A1
A0
DB9 DB8
DB7
DB6 DB5 DB4
DB3 DB2
DB1 DB0
X = Don’t Care
*Applicable to the AD7808 Only, and Are Don’t Care Conditions when Operating the AD7804 .
Figure 6. AD7804/AD7808 Main DAC Data Register Loading Sequence (MAIN /SUB = 0)
DB15 (MSB)
MAIN/SUB
DB0 (LSB)
MD0 = X MD1 = 1 A2* A1
A0
DB7 DB6
DB5
DB4 DB3 DB2
DB1 DB0
X
X
X = Don’t Care
*Applicable to the AD7808 Only, and Are Don’t Care Conditions when Operating the AD7804.
Figure 7. AD7804/AD7808 Sub DAC Data Register Loading Sequence (MAIN /SUB = 1)
AD7804/AD7808 SYSTEM CONTROL REGISTER (MD1 = 0,
MD0 = 0)
When the system control register is selected by writing zeros to
the mode bits, MD1 and MD0 the address bits are ignored as
the system control register controls all DACs in the package.
When MD1 = 0 and MD0 = 1, writing is to the channel control
register. Only the DAC selected by the address bits will be affected by writing to this register. Each individual DAC has a
channel control register.
The bits in this register allow control over all DACs in the
package. The control bits include power down (PD), DAC input
coding select (BIN/COMP), system standby (SSTBY) and a
system clear (SCLR). The function of these bits is as follows:
Power Down (PD)
The DACs data registers are addressed by writing a one to
MD1 (DB13); the condition of MD0 (DB14) does not matter
when writing to the data registers. DB15 determines whether
writing is to the Main DAC data register or to the Sub DAC
data register. The Main DAC is 10 bits wide and the Sub DAC
is 8 bits wide. Thus when writing to the Sub DAC DB1 and
DB0 become don’t cares. The Sub DAC is used to offset the
complete transfer function of the Main DAC around its VBIAS
point. The Sub DAC has 1/8 LSB resolution and will enable the
transfer function of the Main DAC to be offset by ± VBIAS/32.
When the LDAC line goes low, all DAC registers in the device
are simultaneously loaded with the contents of their respective
DAC data registers, and the outputs change accordingly.
Bringing the CLR line low resets the DAC data and DAC registers. This hardware clear affects both the Main and Sub DACs.
This operation sets the analog output of the Main DAC to VBIAS/
16 when offset binary coding is selected and the output is set to
VBIAS when twos complement coding is used. VBIAS is the output
of the internal multiplexer as shown in Figure 3. The output of
the Sub DAC is used to shift the transfer function of the Main
DAC around the VBIAS point and the contribution from the Sub
DAC is zero following an external hardware clear. Software
clears affect the Main DACs only.
This bit in the control register is used to shut down the complete
device. With a 0 in this position, the reference and all DACs are
put into low power mode. Writing a 1 to this bit puts the part in
the normal operating mode. When in power-down mode, the
contents of all registers are retained and are valid when the
device is put back into normal operation.
Coding (BIN/COMP)
This bit in the system control register allows the user to select
one of two input coding schemes. The available schemes are
Twos complement coding and offset binary coding. All DACs
will be configured with the same input coding scheme. Writing
a zero to the control register selects twos complement coding,
while writing a 1 to this bit in the control register selects offset
binary coding.
With twos complement coding selected the output voltage from
the Main DAC is of the form :
VOUT = VBIAS ± VSWING
where
VSWING is 15 × VBIAS
16
With Offset Binary coding selected the output voltage from the
Main DAC ranges from:
VOUT =
–10–
VBIAS
to VOUT = 31 × VBIAS
16
16
REV. A
AD7804/AD7805/AD7808/AD7809
VBIAS can be the internal bandgap reference, the internal VDD/2
reference or the external REFIN as determined by MX1 and
MX0 in the channel control register. A second external reference can be used if required by overdriving the VDD/2 reference
which appears at the COMP pin.
Standby (STBY)
This bit allows the selected DAC in the package to be put into
low power mode. Writing a zero to the STBY bit in the channel
control register puts the selected DAC into standby mode. On
writing a zero to this bit all linear circuitry is switched off and
the DAC output is connected through a high impedance to
ground. The DAC is returned to normal operation by writing a
one to the STBY bit.
System Standby (SSTBY)
This bit allows all the DACs in the package to be put into low
power mode simultaneously but the reference is not affected.
Writing a one to the SSTBY bit in the system control register
puts all DACs into standby mode. On writing a one to this bit
all linear circuitry is switched off and the DAC outputs are
connected through a high impedance to ground. The DACs come
out of standby mode when a 0 is written to the SSTBY bit.
Software Clear Function (CLR)
System Clear Function (SCLR)
This function allows the user to clear the contents of all data
and DAC registers in software. Writing a one to the SCLR bit
in the control register clears the DAC’s outputs. A zero in this
bit position puts the DAC in normal operating mode. The output of the Main DACs are cleared to one of two voltages depending on the input coding used. If twos complement coding
is selected, then issuing a software clear will reset the output of
the Main DAC to midscale (VBIAS). If offset binary coding is
selected, the Main DAC output will be reset to VBIAS /16 following the execution of a software clear. This system clear function
does not affect the Sub DAC; the Sub DAC data register retains
its value during a system software clear (SCLR).
This function allows the user to clear the contents of the selected DAC’s data in software. Writing a one to the CLR bit in
the control register clears the DAC’s output. A zero in the CLR
bit position puts the DAC in normal operating mode. This
software CLR operation clears only the Main DAC, the contents of the Sub DAC is unaffected by a CLR operation. The
output of the Main DAC can be cleared to one of two places
depending on the input coding used. An LDAC pulse is required to activate the channel clear function and must be applied after the bit in the channel control register is set or reset. If
twos complement coding is selected, then issuing a software
clear will reset the output of the Main DAC to midscale (VBIAS).
If offset binary coding is selected, the Main DAC output will be
reset to VBIAS/16 following the execution of a software clear.
Multiplexer Selection (MX1, MX0)
These two bits are used to select the reference input for the
selected DAC. Table III shows the options available.
Table III. Multiplexer Output Selection
AD7804/AD7808 CHANNEL CONTROL REGISTER (MD1 = 0,
MD0 = 1)
This register allows the user to have control over individual
DACs in the package. The control bits in this register include
the address bits for the selected DAC, standby (STBY), individual DAC clear (CLR) and multiplexer output selection
(MX1 and MX0). The function of these bits follows.
MX1
MX0
VBIAS
0
0
1
1
0
1
0
1
VDD/2
INTERNAL VREF
REFIN
Undetermined
DAC Selection (A2, A1, A0)
Bits A2, A1 and A0 in the input registers are used to address a
specific DAC. Table IIa shows the selection table for the DACs
of the AD7804. Table IIb shows the selection table for the
DACs of the AD7808.
Table IIa. DAC Selection Table for the AD7804
A2
A1
A0
Function
X
X
X
X
0
0
1
1
0
1
0
1
DAC A Selected
DAC B Selected
DAC C Selected
DAC D Selected
Table IIb. DAC Selection Table for the AD7808
REV. A
A2
A1
A0
Function
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
DAC A Selected
DAC B Selected
DAC C Selected
DAC D Selected
DAC E Selected
DAC F Selected
DAC G Selected
DAC H Selected
AD7804/AD7808 SUB DAC DATA REGISTER
Figure 7 shows the loading sequence for writing to the data
registers of the DACs. DB15 determines whether writing is to
the Main or Sub DAC’s data register. A one in this position
selects the addressed Sub DAC’s data register. The Sub DAC is
8 bits wide and thus DB1 and DB0 of the 16-bit input word are
don’t cares when writing to the Sub DAC. This Sub DAC allows the complete transfer function of each individual DAC to
be offset around the VBIAS point. This is achieved by either
adding or subtracting to the output of the Main DAC. This Sub
DAC has a span of ± VBIAS/32 with 1/8-bit resolution. The
coding scheme for the Sub DAC is the same as that for the
Main DAC. With offset binary coding the transfer function for
the Sub DAC is
VBIAS (NB – 128)
×
16
256
where NB is the digital code written to the Sub DAC and varies
from 0 to 255.
With twos complement coding the transfer function for the Sub
DAC is
V BIAS
× NB
256
16
where NB is the digital code written to the Sub DAC and varies
from –128 to 127. VBIAS can be either the internal bandgap
reference, the internal VDD/2 reference or the external REFIN as
( )
–11–
AD7804/AD7805/AD7808/AD7809
determined by MX1 and MX0 in the channel control register as
shown in Table III. The internal VDD/2 reference is provided at
the COMP pin. This internal reference can be overdriven with
an external reference thus providing the facility for two external
references.
POWER-UP
SYSTEM
CONFIGURATION
WRITE TO SYSTEM
CONTROL REGISTER
WRITE TO CHANNEL
CONTROL REGISTER
CHANNEL
CONFIGURATION
AD7804/AD7808 POWER-UP CONDITIONS
When power is applied to the device, the device will come up in
standby mode where all the linear circuitry excluding the reference are switched off. Figure 8 shows the relevant default values for the system control register. Since a write to the system
control register is required to remove the standby condition the
only bits for which default conditions are applicable are PD and
SSTBY. Figure 9 details the relevant default conditions for the
Channel Control Register.
PD
SSTBY
1
1
ALL CHANNELS
CONFIGURED
N
Y
WRITE TO SELECTED
MAIN OR SUB DAC
DATA REGISTERS
DATA LOADING
COMPLETE
DATA WRITE
N
Y
Figure 8. Default Conditions for System Control Register
on Power-Up
STBY
CLR
MX1
MX0
1
1
0
0
Y
N
Y
Figure 9. Default Conditions for Channel Control Register
on Power-Up
After power has been applied to the device the following procedure should be followed to communicate and set up the device.
First, a write to the system control register is required to clear
the SSTBY bit and change the input coding scheme if required.
For example, to remove standby and set up offset binary input
coding 0060Hex should be written to the input register, if twos
complement coding is required 0020Hex should be written to
the input register. MD1 and MD0 are decoded in the input
register and this allows the data to be written to the system
control register.
Step two requires writing to the channel control register, which
allows individual control over each DAC in the package and
allows the VBIAS for the DAC to be selected as well as individual
DAC standby and clear functions. For example, if channel A is
to be configured for normal operation with internal reference
selected then 4110Hex should be written to the input register.
In the input register, the MD1 and MD0 bits are decoded in
association with the address bits to give access to the required
channel control register. The third and final step is to write data
to the selected DAC. To write half scale to channel A Main
DAC, 2200Hex should be written to the input register, the
MSB in the sixteen bit stream selects the Main DAC and the
next three bits address the DAC and the final 10 bits contain
the data. To write half scale to channel A Sub DAC, then A200
should be written to the input register. The flowchart in Figure
10 shows in graphic form the steps required in communicating
with the AD7804/AD7808.
CHANGE
CHANNEL
CONFIGURATION
CHANGE
SYSTEM
CONFIGURATION
N
END
Figure 10. Flowchart for Controlling the DAC Following
Power-Up
AD7805/AD7809 INTERFACE SECTION
The AD7805 and AD7809 are parallel data input devices and
contain both control registers and data registers. The system
control register has global control over all DACs in the package
while the channel control register allows control over individual
DACs in the package. Two data registers are also available, one
for the 10-bit Main DAC and the second for the 8-bit Sub
DAC. In the parallel mode, CS and WR, in association with the
address pins, control the loading of data. Data is transferred
from the data register to the DAC register under the control of
the LDAC signal. Only data contained in the DAC register determines the analog output of any DAC. The timing diagram for
10-bit parallel loading is shown in Figure 2. The MODE pin on
the device determines whether writing is to the data registers or
to the control registers. When MODE is at a logic one, writing
is to the data registers. In the next write to the data registers a
bit in the channel control register determines whether the Main
DAC or the Sub DAC is addressed. This means that to address
either the Main or the Sub DAC the Main/Sub bit in the control
register has to be set appropriately before the data register write.
A logic zero on the mode pin enables writing to the control
register. Bit MD0 determines whether writing is to the system
control register or to the addressed channel control register.
Bringing the CLR line low resets the DAC registers to one of
two known conditions depending on the coding scheme selected. The hardware clear affects both the Main and Sub
DAC registers. With offset binary coding a clear sets the output
–12–
REV. A
AD7804/AD7805/AD7808/AD7809
of the Main DAC to the bottom of the transfer function, VBIAS/16.
With twos complement coding the output of the DAC is cleared
to midscale which is VBIAS. A hardware clear always clears the
output of the Sub DAC to midscale thus the output of the Sub
DAC makes zero contribution to the output of the channel.
MODE ADDR
CS
WR
LDAC
CONTROL
LOGIC
DECODER
CHANNEL
CONTROL
REGISTER
DATA REGISTER
SINGLE
CHANNEL
10
8
DAC REGISTER
10
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
VBIAS
X
X
X
X
X
X
X
DB1 DB0
DB1
DB0
0 MAIN/SUB
1 MAIN/SUB
X = Don’t Care
Figure 15. AD7805/AD7809 Main DAC Data Register Configuration (MODE = 1, 10 /8 = 1, MAIN /SUB = 0)
Figure 11. AD7805/AD7809 Internal Registers
Figure 16 shows the bit allocations for writing to the Sub DAC.
AD7805/AD7809 CONTROL REGISTERS
Access to the control registers of the AD7805/AD7809 is
achieved by taking the mode pin to a logic low. The control
register of these DACs are configured as in Figures 12 and 13.
There are two control registers associated with the part. System
control register which looks after the input coding, data format,
power down, system clear and system standby. The channel
control register contains bits that affect the operation of the
selected DAC. The external address bits are used to select the
DACs. These registers are eight bits wide and the last two bits
are control bits. The mode pin must be low to have access to the
control registers.
DB9
DB2 DB1
PD SSTBY SCLR 0
X
DB0
MD0 = 0
X = Don’t Care
Figure 12. AD7805/AD7809 System Control Register Configuration, (MODE = 0)
DB9
MX1 MX0 MAIN/SUB X
DB2
DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2
MUX
X X 10/8 BIN/COMP
X
X = Don’t Care
DB9
8
REFIN
DB2
X
STBY CLR 0
DB1
X
DB9
MD0 = 1
Figure 13. AD7805/AD7809 Channel Control Register Configuration (MODE = 0)
The external mode pin must be taken high to allow data to be
written to the DAC data registers. Figure 14 shows the bit allocations when 10-bit parallel operation is selected in the system
control register.
DB2 DB1
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
DB0
X MAIN/SUB
X = Don’t Care
Figure 16. AD7805/AD7809 Sub DAC Data Register Configuration (MODE = 1, MAIN /SUB = 1)
Each DAC has a separate channel control register. The following is a brief discussion on the bits in each of the control registers.
DAC Selection (A2, A1, A0)
The external address pins in conjunction with CS, WR and
MODE are used to address the various DAC data and control
registers. Table IVa shows how these DAC registers can be
addressed on the AD7805. Table IVb shows how these registers
are addressed on the AD7809. Refer to Figures 12 to 16 for information on the registers.
Table IVa. AD7805 DAC Data/Control Register
Selection Table
DB0
X = Don’t Care
REV. A
DB0
8-BIT DAC
(SUB DAC)
10-BIT DAC
(MAIN DAC)
VOUT
INTERNAL VREF
VDD/2
DATA REGISTER
DAC REGISTER
DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1
Figure 15 shows the bit allocations when 8-bit parallel operation
is selected in the system control register. DB9 to DB2 are retained as data bits. DB1 acts as a high byte or low byte enable.
When DB1 is low, the eight MSBs of the data word are loaded
to the input register. When DB1 is high, the low byte consisting
of the two LSBs are loaded to the input register. DB0 is used to
select either the Main or Sub DAC when in the byte mode.
SYSTEM
CONTROL
REGISTER
TO ALL
CHANNELS
DB0
Figure 14. AD7805/AD7809 Main DAC Data Register (Top)
and Sub DAC Data Register (Bottom) Configuration
(MODE = 1, 10/8 = 0)
D9 D2 D1 D0
INPUT REGISTER
DB9
MODE
A1
A0
Function Selected
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
DAC A Control Registers
DAC B Control Registers
DAC C Control Registers
DAC D Control Registers
DAC A Data Registers
DAC B Data Registers
DAC C Data Registers
DAC D Data Registers
–13–
AD7804/AD7805/AD7808/AD7809
Table IVb. AD7809 DAC Data/Control Register
Selection Table
MODE
A2
A1
A0
Function Selected
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
DAC A Control Register
DAC B Control Register
DAC C Control Register
DAC D Control Register
DAC E Control Register
DAC F Control Register
DAC G Control Register
DAC H Control Register
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
DAC A Data Register
DAC B Data Register
DAC C Data Register
DAC D Data Register
DAC E Data Register
DAC F Data Register
DAC G Data Register
DAC H Data Register
System Clear
SCLR
0
Normal operation.
1
All DACs in the package are cleared to a known state
depending on the coding scheme selected. The SCLR bit
clears the Main DACs only; the Sub DACs are unaffected by the system clear function. The main DAC is
cleared to different levels depending on the coding
scheme. With offset binary coding the Main DAC output
is cleared to the bottom of the transfer function VBIAS/16.
With twos complement coding the Main DAC output is
cleared to midscale VBIAS. The channel output will be the
sum of the Main DAC and Sub DAC contributions.
AD7805/AD7809 CHANNEL CONTROL REGISTER
This register allows the user to have control over individual
DACs in the package. The control bits in this register include
multiplexer output selection (MX1 and MX0), Main or Sub
DAC selection (MAIN/SUB), standby (STBY) and individual
DAC clear (CLR). The function of these bits is as follows.
Multiplexer Selection (MX1, MX0)
Table V shows the VBIAS selection using MX1 and MX0 bits in
the channel control register.
AD7805/AD7809 SYSTEM OR CHANNEL CONTROL
REGISTER SELECTION
Table V. VBIAS Selection Table
MD0
0
1
This enables writing to the system control register.
The contents of this are shown in Figure 12. Mode
must be low to access this control register.
This enables writing to the channel control register.
The contents of this are shown in Figure 13. Mode
must also be low to access this control register.
MX1
MX0
VBIAS
0
0
1
1
0
1
0
1
VDD/2 (Default on Power-Up)
INTERNAL VREF
REFIN
Undetermined
Main DAC or Sub DAC Selection
AD7805/AD7809 SYSTEM CONTROL REGISTER
0
10-bit parallel loading structure.
MAIN/SUB
0
Writing a 0 to this bit means that the data in the next
data register write is transferred to the selected Main
DAC.
1
Writing a 1 to this bit means that the data in the next
data register write is transferred to the selected Sub DAC.
This applies to the 10-bit parallel load feature. In byte
load mode, (Figure 15) DB0 selects the Main or Sub
DAC data registers.
1
Byte loading structure. (8+2 loading).
Standby
The bits in this register allow control over all DACs in the package. The control bits include data format (10/8), power down
(PD), DAC input coding select (BIN/COMP), system standby
(SSTBY) and a system clear (SCLR). The function of these bits
is as follows:
Data Format
10/8
Input Coding
BIN/COMP
0
Twos complement coding.
1
Offset Binary Coding.
Power Down
PD
0
Complete power-down of device.
1
Normal operation (default on power-up).
STBY
0
1
Clear
CLR
0
1
System Standby
SSTBY
0
Normal operation.
1
All DACs in the package put in standby mode (default
on power-up).
Places the selected DAC and its associated linear circuitry in Standby Mode.
Normal operation (default on power-up).
–14–
Normal operation.
Clears the output of the selected Main DAC to one
of two conditions depending on the input coding selected. With offset binary coding the Main DAC output is cleared to the bottom of the transfer function,
VBIAS/16 and with twos complement coding the Main
DAC output is cleared to midscale VBIAS. The Sub
DAC is unaffected by a clear operation. An LDAC
signal has to be applied to the DAC for a channel clear
to be implemented.
REV. A
AD7804/AD7805/AD7808/AD7809
POWER-UP CONDITIONS (POWER-ON RESET)
START
When power is applied to the AD7805/AD7809 the device
powers up in a known condition. The device powers up in system standby (SSTBY) mode where all DACs in the package are
in low power mode, the reference is active and the outputs of
the DACs are connected internally through a high impedance to
ground. Figure 17 show the default conditions for the system
control register. Since a write to the system control register is
required to remove the standby condition, relevant default conditions are only applicable for PD and SSTBY in the system
control register. The following are the bits in the channel control register for which default conditions are applicable, STBY,
CLR, MX1 and MX0. Figure 18 shows the default conditions
for the channel control register.
PD
SSTBY
1
1
WRITE TO SYSTEM
CONTROL REGISTER
Y
WRITE TO CHANNEL
CONTROL REGISTER
N
WRITE TO
SUB DAC
WRITE TO MAIN DAC
DATA REGISTER
N
WRITING
COMPLETE
Y
Y
Y
WRITE TO CHANNEL
CONTROL REGISTER
WRITE TO SUB DAC
DATA REGISTER
RECONFIGURE
SYSTEM
N
N
END
STBY
CLR
MX1
MX0
1
1
0
0
WRITING
COMPLETE
Y
Figure 17. Default Conditions for the AD7805/AD7809
System Control Register on Power-Up
Figure 19. Flowchart for Controlling the AD7805/AD7809
DACs in 10-Bit Parallel Mode Following Power-Up
mode as the selection can be made using the hardware bit DB0 and
this will reduce the software overheads when accessing the DACs.
CLEAR FUNCTIONS
Figure 18. Default Conditions for the AD7805/AD7809
Channel Control Register on Power-Up
The flowchart in Figure 19 shows the steps necessary to control
the AD7805/AD7809 following power-on. This flowchart details the necessary steps when using the AD7805/AD7809 in its
10-bit parallel mode. The first step is to write to the system
control register to clear the SSTBY bit and to configure the part
for 10-bit parallel mode and select the required coding scheme.
The next step is to determine whether writing is to the Main or
Sub DAC. This is achieved by writing to the channel control
register. Other bits that need to be configured in the channel
control register are MX1 and MX0 which determine the source
of the VBIAS for the selected DAC and the channel STBY and
channel CLR bits need to be configured as desired. Once writing to the channel control register is complete, data can now be
written to the selected Main or Sub DAC.
Parallel data can also be written to the device in 8+2 format to
allow interface to 8-bit processors. Eight-bit mode is invoked by
writing a one to the 10/8 bit in the system control register.
When in the 8-bit mode the two unused data bits (DB1 and
DB0) are used as hardware control bits and have the same timing characteristics as the address inputs. DB1 is a don’t care bit
when writing to both the system and channel control registers;
DB0 acts as the mode select bit and must be low to enable writing to the system control register and when high enables access
to the channel control register.
There are three methods of clearing the output of the Main
DAC in these devices. The first is the external hardware clear.
An active low logic signal applied to this pin clears all the DACs
in the package. The voltage to which the output is cleared will
depend on the input coding selected. The Main DAC outputs
are cleared to midscale (VBIAS) in twos complement format and
to the bottom of the transfer function (VBIAS/16) in offset binary
format. The second way of clearing the main DACs is a software
clear by asserting the SCLR bit in the system control register of
the part. Writing a one to this bit clears all DACs in the package. The third method of clearing a DAC is to write a one to the
CLR bit in the channel control register. This differs from that of
the system control register in that only the selected DACs output is cleared. The channel clear requires an LDAC pulse to
activate it.
There is only one way of clearing the output of the Sub DAC
and that is to use the external hardware clear. The output of the
Sub DAC is cleared to midscale (0 V) regardless of the input
coding being used. Figure 20 shows a simplified diagram of the
implementation of the clear functions for a single DAC in the
package.
When in the 8-bit data write mode, DB1 acts as a low byte and
high byte enable, when low data is written to the 8 MSBs of the
DAC and when high data is written to the two LSBs. DB0 acts
as a bit to select writing to the Main or Sub DAC. When DB0 is
low, writing is to the Main DAC, and when high, writing is to
the Sub DAC data register. In the 8+2 mode the channel control register does not have to be accessed to switch between
writing to the Main and Sub DACs as in the 10-bit parallel
REV. A
WRITE TO
MAIN DAC
–15–
EXT CLR
SYSTEM CLR
CLR
SUB DAC
CHANNEL CLR
LDAC
CLR
A2
A1
ADDR
DECODER
MAIN DAC
A0
ALL OTHER CIRCUITRY OMITTED FOR CLARITY
Figure 20. CLR Functions for Main and Sub DACs
AD7804/AD7805/AD7808/AD7809
POWER-DOWN AND STANDBY FUNCTIONS
ANALOG OUTPUTS
There are two distinct low power modes on the device, powerdown mode and standby mode. When in power-down mode all
circuitry including the reference are put into low power mode
and power dissipation from the package is at its minimum.
The AD7804 and AD7805 DACs contain four independent
voltage output Main DACs with 10-bit resolution. The AD7808
and AD7809 contain eight independent voltage output main
DACs with 10-bit resolution. Each Main DAC has an associated Sub DAC with 8-bit resolution which can be used to offset
the complete transfer function of the Main DAC around the
VBIAS point. These DACs produce an output voltage in the form
of VBIAS ± VSWING where VSWING is 15/16 of V BIAS.
SYSTEM PD
STANDBY
INT
REFERENCE
CHANNEL STBY
The digital input code to these DACs can be in twos complement or offset binary form. All DACs will be configured with
the same input coding scheme which is programmed through
the system control register. The default condition on power-up
is for offset binary coding.
STANDBY
A2
A1
ADDR
DECODER
MAIN & SUB
DAC
A0
ONLY ONE DAC SHOWN FOR CLARITY
Figure 21. Implementation of Power-Down and Standby
Functions
TWOS COMPLEMENT CODING
Table VI shows the twos complement transfer function for the
Main DAC.
The standby functions allow either the selected DAC or all DACs
in the package to be put into low power mode. The reference is
not switched off when any of the standby functions are invoked.
Table VI. Twos Complement Code Table for Main DAC
The PD bit in the system control register is used to shut down
the complete device. With a 0 in this position the reference and all
DACs are put into low power mode. Writing a 1 to this bit puts the
part in the normal operating mode. When in power-down mode
the contents of all registers are retained and are valid when the
device is taken out of power down. The SSTBY bit which resides
in the system control register can be used to put all DACs and
their associated linear circuitry into standby mode, the SSTBY
function does not power down the reference. The STBY bit in
the channel control register can be used to put a selected DAC
and its associated linear circuitry into standby mode. Figure 18
shows a simplified diagram of how the power-down and standby
functions are implemented for a single DAC in the package.
LDAC FUNCTION
LDAC input is a logic input that allows all DAC registers to be
simultaneously updated with the contents of the DAC data
registers. LDAC input has two operating modes, a synchronous
mode and an asynchronous mode. The LDAC input condition is
sampled on the sixteenth falling edge on the AD7804/AD7808 and
is sampled on the rising edge of write on the AD7805/AD7809. If
LDAC is low on the sixteenth falling clock edge or on the rising
edge of WR, an automatic or synchronous update will take place.
LDAC input can be tied permanently low or have timing similar
to that of the data inputs to operate in the synchronous mode.
Digital Input
MSB . . . LSB
Analog Output
0111111111
0111111110
VBIAS(1+1.875 × 511/1024)
VBIAS(1+1.875 × 510/1024)
0000000001
0000000000
VBIAS(1+1.875 × 1/1024)
VBIAS
1111111111
VBIAS(1–1.875 × 1/1024)
1000000001
1000000000
VBIAS(1–1.875 × 511/1024)
VBIAS(1–1.875 × 512/1024)
Figure 22 shows the Main DAC transfer function for twos
complement coding. Any Main DAC output voltage can be
expressed as:
VOUT' = VBIAS + 1.875 × VBIAS × NA/1024
where NA is the decimal equivalent of the twos complement
input code. NA ranges from –512 to +511.
31
16 VBIAS
DAC OUTPUT VOLTAGE
SYSTEM STBY
If LDAC is high during the sample period, the AD7804/AD7805/
AD7808/AD7809 assumes an asynchronous update. When in
the asynchronous mode, an LDAC setup time has to be allowed
following the sixteenth falling clock edge or the rising edge of
WR before the LDAC can be activated.
VBIAS
VBIAS
16
DAC INPUT CODE 200
201
3FF 000 001
1FE
1FF
Figure 22. Main DAC Output Voltage vs. DAC Input Codes
(HEX) for Twos Complement Coding
–16–
REV. A
AD7804/AD7805/AD7808/AD7809
Configuring the AD7805/AD7809 for Twos Complement Coding
Table VII shows the twos complement transfer function for the
Sub DAC. Figure 23 shows the Sub DAC transfer function for
twos complement coding. Any Sub DAC output voltage can be
expressed as:
Figure 24 shows a typical configuration for the AD7805/AD7809.
The circuit can be used for either 3.3 V or 5 V operation and uses
the internal VDD /2 as the reference for the part and 10-bit parallel interfacing is used. The following are the steps required to
operate the Main DACs in this part.
VOUT" = VBIAS/16 × (NB/256)
where NB is the decimal equivalent of the twos complement
input code. NB ranges from –128 to +127.
+3.3V/+5V
Table VII. Twos Complement Code Table for Sub DAC
Digital Input
MSB . . . LSB
Analog Input
0.01mF
AVDD DVDD
COMP
(VBIAS/16) × (127/256)
(VBIAS/16) × (126/256)
(VBIAS/16) × (1/256)
0
(–VBIAS/16) × (1/256)
(–VBIAS/16) × (127/256)
(–VBIAS/16) × (128/256)
01111111
01111111
00000001
00000000
11111111
10000001
10000000
0.1mF
0.1mF
10mF
REFIN
0.01mF
REFOUT
A2*
A0
AD7805/
AD7809
A1
VOUTA
D9
DIGITAL
INTERFACE
VOUTB
D0
MODE
VOUTC
CS
127 3VBIAS
256
16
WR
VOUTD
CLR
DVDD
DAC OUTPUT VOLTAGE
LDAC
DGND
AGND
*USED ON THE
AD7809 ONLY
0
Figure 24. Typical Configuration for AD7805/AD7809
System Control Register Write:
MODE = 0, address inputs (A2, A1, A0) are don’t cares.
128 3VBIAS
256
16
DAC INPUT CODE 80
Write 020 Hex
81
FF 00
01
7E
Channel Control Register Write:
7F
MODE = 0, address inputs (A2, A1, A0) select desired channel.
Figure 23. Sub DAC Output Voltage vs. DAC Input Codes
(HEX) for Twos Complement Coding
Write 011 Hex
The total output for a single channel when using twos complement coding is the sum of the voltage from the Main DAC and
the Sub DAC.
Internal VDD/2 selected as VBIAS for
DAC, and any DAC data writes that
follow are to the Main DAC.
DAC Data Register Write:
VOUT = VOUT' + VOUT"
= VBIAS + 1.875 × VBIAS × (NA/1024) + VBIAS/16 × (NB/256)
= VBIAS × (1 + 1.875 × NA/1024 + NB/4096)
where NA ranges from –512 to +511 and NB ranges from –128 to
+127. Figure 28 shows a pictorial view of the transfer function for
any DAC.
REV. A
Configure part for 10-bit parallel, twos
complement coding, normal operation
–17–
MODE = 1, address inputs (A2, A1, A0) select desired channel.
Write XXX Hex With MODE = 1 all data writes are to
the selected DAC. XXX is the required
data. 200 Hex will give zero scale and 1FF
Hex will give full scale from the DAC.
AD7804/AD7805/AD7808/AD7809
Table VI and Figure 22 show the analog outputs available for
the above configuration. The following is the procedure required if the complete transfer function needs to be offset
around the VBIAS point. Table VII and Figure 23 show the analog output variations available from the Sub DAC.
OFFSET BINARY CODING
System Control Register Write:
Digital Inputs
MSB . . . LSB
Analog Output
1111111111
1111111110
1000000001
1000000000
0111111111
0000000001
0000000000
VBIAS+1.875 × VBIAS(1023–512)/1024
VBIAS+1.875 × VBIAS(1022–512)/1024
VBIAS+1.875 × VBIAS/1024
VBIAS
VBIAS+1.875 × VBIAS(511–512)/1024
VBIAS+1.875 × VBIAS(1–512)/1024
VBIAS/16
Table VIII shows the offset binary transfer function for the Main
DAC.
Table VIII. Offset Binary Code Table for Main DAC
MODE = 0, address inputs (A2, A1, A0) are don’t cares.
Write 020 Hex
Configure part for 10-bit parallel, twos
complement coding, normal operation
Channel Control Register Write:
MODE = 0, address inputs (A2, A1, A0) select desired channel.
Write 091 Hex
Internal VDD/2 selected as VBIAS for
DAC, and any DAC data writes that
follow are to the Sub DAC.
NOTE: The span range is (30/16) × VBIAS = 1.875 × VBIAS
DAC Data Register Write:
31
16 VBIAS
MODE = 1, address inputs (A2, A1, A0) select desired channel.
With MODE = 1 all data writes are to
the selected DACs Sub DAC. XX is the
required data. 7F Hex will give zero scale
and 80 Hex will give full scale from the
Sub DAC.
DAC OUTPUT VOLTAGE
Write XX Hex
Channel Control Register Write:
MODE = 0, address inputs (A2, A1, A0) select desired channel.
Write 011 Hex
Internal VDD/2 selected as VBIAS for
DAC, and any DAC data writes that
follow are to the Main DAC.
VBIAS
VBIAS
16
DAC Data Register Write:
DAC INPUT CODE 000
001
1FF 200 201
3FE
3FF
MODE = 1, address inputs (A2, A1, A0) select desired channel.
Write XXX Hex With MODE = 1 all data writes are to
the selected Main DAC. XXX is the
required data. 1FF Hex will give zero
scale and 200 Hex will give full scale
from the DAC.
Figure 25. Main DAC Output Voltage vs. DAC Input Codes
(HEX) for Offset Binary Coding
Figure 25 shows the Main DAC transfer function when offset
binary coding is used. With offset binary coding selected the
output voltage can be calculated as follows:
VOUT' = VBIAS + 1.875 × VBIAS × ((NA-512)/1024)
where NA is the decimal equivalent of the offset binary input
code. NA ranges from 0 to 1023.
Table IX shows the offset binary transfer function for the Sub
DAC. Figure 26 shows the Sub DAC transfer function for
offset binary coding. Any Sub DAC output voltage can be
expressed as:
VOUT" = VBIAS/16 × [(NB-128)/256]
where NB is the decimal equivalent of the offset binary input
code. NB ranges from 0 to 255.
–18–
REV. A
AD7804/AD7805/AD7808/AD7809
Table IX. Offset Binary Code Table for Sub DAC
Digital Input
MSB . . . LSB
Analog Output
11111111
11111110
10000001
10000000
01111111
00000001
00000000
VBIAS/16 × 127/256
VBIAS/16 × 126/256
VBIAS/16 × 1/256
0
–VBIAS/16 × 1/256
–VBIAS/16 × 127/256
–VBIAS/32
+3.3V/+5V
10mF
0.1mF
0.1mF
6.8kV
0.01mF
AVDD DVDD
COMP
REFIN
0.01mF
AD589
AD7804/
AD7808
FSIN
SERIAL
INTERFACE
REFOUT
SDIN
VOUTA
CLKIN
VOUTB
VOUTC
127 3 VBIAS
128
32
DVDD
CLR
VOUTD
LDAC
DAC OUTPUT VOLTAGE
DGND
0
AGND
Figure 27. Typical Configuration for AD7804/AD7808
Using an AD589 1.23 V Reference for the AD7804/AD7808
System Control Register Serial Write:
Write 0060 Hex Mode bits select system control register
and configure system for offset binary
coding and normal operation.
VBIAS
32
DAC INPUT CODE 00
01
7F 80
81
FE
FF
Channel Control Register Serial Write:
Write 4210 Hex
Figure 26. Sub DAC Output Voltage vs. DAC Input Codes
(HEX) for Offset Binary Coding
Configuring the AD7804/AD7808 for Offset Binary Coding
Figure 27 shows a typical configuration for the AD7804/AD7808.
This circuit can be used for both 3.3 V or 5 V operation and
uses an external AD589 as the reference for the part and serial
interfacing with offset binary coding is used. The MX1 and
MX0 bits in the system control register have to be set to enable
selection of the AD589 as the reference. The following are the
steps required to operate the DACs in this part. Figures 4 to 7
show the contents of the registers on the AD7804/AD7808.
Mode bits select channel control register,
channel A is configured for operation with
external reference.
Main DAC Data Register Serial Write:
Write 23FF Hex
This 16-bit write selects writing to channel
A and writes full scale to the Main DAC.
Sub DAC Data Register Serial Write:
Write A3FF Hex This 16-bit write selects writing to channel
A Sub DAC and writes full scale to the
Sub DAC.
Table VIII and Figure 25 show the analog outputs available for
the above configuration when writing to the Main DAC only
while Table IX and Figure 26 show the contributions from the
Sub DAC to the overall transfer function. The total output for a
single channel when using offset binary coding is the sum of that
from the Main DAC and the Sub DAC.
VOUT = VOUT' + VOUT"
= VBIAS + 1.875 × VBIAS × ((NA-512)/1024) + VBIAS/16
= × [(NB-128)/256]
= VBIAS × (1 + 1.875 × ((NA-512)/1024) + (NB-128)/
4096)
where NA ranges from 0 to +1023 and NB ranges from 0 to
+255. Figure 28 shows a pictorial view of the transfer function
for any DAC channel.
REV. A
–19–
AD7804/AD7805/AD7808/AD7809
MAIN DAC RANGE
2
1
32
32
32
VBIAS
3
VBIAS
V
32 BIAS
31
32
VBIAS
32
62
VBIAS
33
32
VBIAS
61
32
VBIAS
32
VBIAS
63
32 VBIAS
SUB DAC
RANGE
CHANNEL RANGE MIN CODE LOADED TO SUB DAC
CHANNEL RANGE CENTER CODE LOADED TO SUB DAC
CHANNEL RANGE MAX CODE LOADED TO SUB DAC
Figure 28. Pictorial View of Transfer Function for Any DAC Channel
Grounding and Layout Techniques
To obtain optimum performance from the AD7804/AD7805/
AD7808/AD7809 care should be taken with the layout. Causes
for concern would be feedthrough from the interface bus onto
the analog circuitry particularly the reference pins and ground
loops. The board should be designed such that the analog and
digital sections are separated as much as possible. Ground planing and shielding should be used as much as possible. Digital
and analog ground planes should only be joined in one place to
avoid ground loops. The ideal place to join the ground planes is
at the analog and digital ground pins of the DAC. Alternatively
a star ground should be established on the board to which all
other grounds are returned. Good decoupling is important in
achieving optimum performance. All supplies, analog or digital,
should be decoupled with 10 µF tantalum and 0.1 µF ceramic
capacitors to their respective grounds, and should be as close as
possible to the pins of the device. The main aim of the bypassing element is to maximize the charge stored in the bypass loop
while simultaneously minimizing the inductance of this loop.
Inductance in the loop acts as an impedance to high frequency
transients and results in power supply spiking. By keeping the
decoupling as close as possible to the device, the loop area is kept
to a minimum thus reducing the possibility of power supply spikes.
On the AD7805 the REFOUT pin of the device is located next
to the DB9 of the data bus, to reduce the risk of digital feedthrough and noise being coupled from the digital section onto
the reference, the REFOUT pin and any trace connected to it
should be shielded with analog ground. To reduce the noise on
this reference it should be decoupled with a 0.01 µF capacitor to
analog ground, keeping the capacitor as close as possible to the
device. The comp pin which is the output from the internal
VDD/2 reference is located next to VOUTD on the DAC and is
sensitive to noise pickup and feedthrough from the DAC output
and thus should be shielded with analog ground to keep this
reference point as quiet as possible. The comp pin should be
decoupled both to AVDD and AGND with 1–10 nF ceramic
capacitors. The external REFIN pin should also be shielded
with analog ground from the digital pins located next to it.
The same precautions should be taken with the reference pins
on the AD7804/AD7808 to reduce the risk of noise pickup and
feedthrough.
Reference Settling Time
With the REFOUT on the AD7804/AD7805/AD7808/AD7809
decoupled with a 0.01 µF capacitor to AGND it takes the
REFOUT approximately 2 ms to fully settle after taking the
device out of power down. When this capacitor is reduced to
1 nF the settling time reduces to 150 µs. The size of the capacitor required on the REFOUT depends to a large extent on the
layout, if the REFOUT is well shielded with AGND the size of
the capacitor can be reduced thus reducing the settling time for
the reference. The internal VDD /2 reference provided at the
comp pin when decoupled with a 1 nF capacitor to both AVDD
and AGND has very fast settling time, typically less than 500 ns.
–20–
REV. A
Typical Performance Characteristics–AD7804/AD7805/AD7808/AD7809
0.150000
2.0
0.125000
INTEGRAL LINEARITY – LSBs
MAIN DAC = ZERO SCALE
SUB DAC = MID SCALE
VBIAS = VDD /2
TA = +258C
0.100000
VOUT – V
VDD = 5.5V
0.075000
VDD = 3V
0.050000
0.025000
1.5
AVDD = DVDD = 5V
VBIAS = VDD /2
1.0
TA = +258C
SUB DAC LOADED WITH
1/2 SCALE
0.5
0.0
–0.5
–1.0
–1.5
SOURCE CURRENT
0.000000
–0.5
–0.4 –0.3
–0.2
SINK CURRENT
–0.1 0.0
0.1
CURRENT – mA
0.2
0.3
0.4
–2.0
0.5
Figure 29. Sink and Source Current with Zero Scale
Loaded to DAC. VDD = 5 V and VDD = 3 V
100
200
300
400 500 600 700
DAC CODE
800
900 1023
Figure 32. Integral Linearity with 5 V Operation
5.200000
2.0
VDD = 5.5V
MAIN DAC = FULL SCALE
SUB DAC = MID SCALE
VBIAS = VDD /2
TA = +258C
INTEGRAL LINEARITY – LSBs
5.180000
0
RL =
VOUT – V
5.160000
RL = 2kV
5.140000
5.120000
1.5
AVDD = DVDD = 3V
VBIAS = VDD /2
1.0
TA = +258C
SUB DAC LOADED WITH
1/2 SCALE
0.5
0.0
–0.5
–1.0
–1.5
SOURCE CURRENT SINK CURRENT
5.100000
–6.0
–4.0
–2.0
0.0
2.0
CURRENT – mA
4.0
–2.0
6.0
Figure 30. Sink and Source Current at Full Scale with
VDD = 5 V
200
300
400 500 600 700
DAC CODE
800
900 1023
1.225
VDD = 3V
MAIN DAC = FULL SCALE
SUB DAC = MID SCALE
VBIAS = VDD /2
TA = +258C
VDD = 3V
RL = 2kV||100pF
CODE CHANGE
011111 1111 TO
100000 0000
TA = +258C
1.224
1.223
DAC OUTPUT
RL =
VOUT – V
100
Figure 33. Integral Linearity with 3 V Operation
2.850000
2.830000
0
2.810000
RL = 2kV
2.790000
1.222
1.221
1.220
1.219
1.218
2.770000
SOURCE CURRENT
2.750000
–6.0
–4.0
–2.0
1.217
SINK CURRENT
0.0
2.0
CURRENT – mA
4.0
1.216
6.0
Figure 31. Sink and Source Current at Full Scale with
VDD = 3 V
REV. A
0
20
40
60
80
100
ns
120
140
160
180
200
Figure 34. Digital-to-Analog Glitch Impulse
–21–
AD7804/AD7805/AD7808/AD7809
MICROPROCESSOR INTERFACING
AD7804/AD7808–ADSP-2101/ADSP-2103 Interface
Figure 35 shows a serial interface between the AD7804/AD7808
and the ADSP-2101/ADSP-2103. The ADSP-2101/ADSP2103 should be set up to operate in the SPORT Transmit Alternate Framing Mode. The ADSP-2101/ADSP-2103 SPORT is
programmed through the SPORT control register and should be
configured as follows: Internal Clock Operation, Active Low
Framing, 16-bit Word Length. Transmission is initiated by
writing a word to the TX register after the SPORT has been
enabled. The data is clocked out on each rising edge of the serial
clock and clocked into the AD7804/AD7808 on the falling edge
of the SCLK.
ADSP-2101/
ADSP-2103*
+5V
AD7804*/
AD7808
CLR
FO
LDAC
TFS
FSIN
DT
SDIN
SCLK
AD7804*/
AD7808
68HC11/68L11*
CLKIN
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 35. ADSP-2101/ADSP-2103 Interface
AD7804/AD7808–68HC11/68L11 Interface
Figure 36 shows a serial interface between the AD7804/AD7808
and the 68HC11/68L11 microcontroller. SCK of the 68HC11/
68L11 drives the CLKIN of the AD7804/AD7808, while the
MOSI output drives the serial data line of the DAC. The FSIN
signal is derived from a port line (PC7). The setup conditions
for correct operation of this interface are as follows: the
68HC11/68L11 should be configured so that its CPOL bit is a 0
and its CPHA bit is a 1. When data is being transmitted to the
DAC the FSIN line is taken low (PC7). When the 68HC11/
68L11 is configured as above, data appearing on the MOSI
output is valid on the falling edge of SCK. Serial data from the
68HC11/68L11 is transmitted in 8-bit bytes with only eight
falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. In order to load data to the AD7804/AD7808,
PC7 is left low after the first eight bits are transferred and a
second serial write operation is performed to the DAC and then
PC7 is taken high at the end of this procedure. In the diagram
shown LDAC and CLR are also controlled from the bit programmable lines of the 68HC11/68L11. The user can bring
LDAC low after every two bytes have been transmitted to update that particular DAC which has been programmed or alternatively it is possible to wait until all the input registers have
been loaded before updating takes place.
PC5
CLR
PC6
LDAC
PC7
FSIN
SCK
CLKIN
MOSI
SDIN
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 36. AD7804/AD7808–68HC11/68L11 Interface
AD7804/AD7808–80C51/80L51 Interface
Figure 37 shows a serial interface between the AD7804/AD7808
and the 80C51/80L51 microcontroller. The setup for the interface is as follows, TXD of the 80C51/80L51 drives CLKIN of
the AD7804/AD7808 while RXD drives the serial data line of
the part. The FSIN signal is again derived from a bit programmable pin on the port in this case port line P3.3 is used. When
data is to be transmitted to the part, P3.3 is taken low. Data on
RXD is valid on the falling edge of TXD. The 80C51/80L51
transmits data in eight bit bytes thus only eight falling clock
edges occur in the transmit cycle. To load data to the DAC,
P3.3 is left low after the first eight bits are transmitted and a
second write cycle is initiated to transmit the second byte of
data, P3.3 is taken high following the completion of this cycle.
The 80C51/80L51 outputs the serial data in a format which has
the LSB first. The AD7804/AD7808 requires its data with the
MSB as the first bit received. The 80C51/80L51 transmit routine should take this into account. In the diagram shown LDAC
and CLR are also controlled from the bit programmable lines of
the 80C51/80L51 port. The user can bring LDAC low after
every two bytes have been transmitted to update that particular
DAC which has been programmed or alternatively it is possible
to wait until all the input registers have been loaded before
updating takes place.
–22–
AD7804*/
AD7808
80C51/80L51*
P3.5
CLR
P3.4
LDAC
P3.3
FSIN
TXD
SCLK
RXD
SDIN
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 37. AD7804/AD7808–80C51/80L51 Interface
REV. A
AD7804/AD7805/AD7808/AD7809
AD7805/AD7809–ADSP-2101 Interface
Figure 38 shows a parallel interface between the AD7805/AD7809
and the ADSP-2101/ADSP-2103 digital signal processor.
Fast interface timing allows the AD7805/AD7809 interface
directly to the DSP. In this interface an external timer is used to
update the DACs.
TIMER
DMA14
ADDRESS BUS
DMA0
ADDR
DECODE
DMS
EN
A0
A1
LDAC
A2**
OUT DAC, D.
DAC = Decoded DAC Address.
D = Data Memory Address.
Certain applications may require that the updating of the DAC
latch be controlled by the microprocessor rather than the external timer. One option as shown in the TMS32020 interface is to
decode the LDAC from the address bus so that a write operation to the DAC latch (at a separate address to the input latch)
updates the output.
MODE
AD7805/AD7809–8051/8088 Interface
CS
AD7805*/
AD7809
ADSP-2101*/
ADSP-2103*
Again fast interface timing allows the AD7805/AD7809 interface directly to the processor. Data is loaded to the AD7805/
AD7809 input latch using the following instruction:
Figure 40 shows a parallel interface between the AD7805/
AD7809 and the 8051/8088 processors.
WR
WR
DB9
A15
ADDRESS BUS
DB0
A8
DMD15
ADDR
DECODE
DATA BUS
DMD0
PSEN OR DEN
**ADDITIONAL PINS OMITTED FOR CLARITY
**A2 CONTAINED ON THE AD7809 ONLY
WR
Figure 38. AD7805/AD7809–ADSP-2101/ADSP-2103
Interface
ALE
AD7805*/
AD7809
OCTAL
LATCH
DB9
AD7
AD0
MR0 = ADSP-2101 MR0 Register.
Figure 40. AD7805/AD7809–8051/8088 Interface
AD7805/AD7809–TMS32020 Interface
Figure 39 shows a parallel interface between the AD7805/AD7809
and the TMS32020 processor.
A15
ADDRESS BUS
A0
ADDR
DECODE
EN
A0 A1 A2**
CS
AD7805*/
AD7809
TMS32020
LDAC
STRB
R/W
ADDRESS/DATA BUS
**ADDITIONAL PINS OMITTED FOR CLARITY
**A2 CONTAINED ON THE AD7809 ONLY
DAC = Decoded DAC Address.
WR
DB9
DB0
DATA BUS
D0
**ADDITIONAL PINS OMITTED FOR CLARITY
**A2 CONTAINED ON THE AD7809 ONLY
Figure 39. AD7805/AD7809–TMS32020 Interface
REV. A
MODE
LDAC
DB0
DM(DAC) = MR0,
D15
A1 A2**
WR
8051/8088
Data is loaded to the AD7805/AD7809 input register using the
following instruction:
IS
EN
A0
CS
–23–
AD7804/AD7805/AD7808/AD7809
APPLICATIONS
Opto-Isolated Interface for Process Control Applications
AD7808
CLKIN
FSIN
The AD7804/AD7808 has a versatile serial three-wire serial
interface making it ideal for generating accurate voltages in
process control and industrial applications. Due to noise, safety
requirements, or distance, it may be necessary to isolate the
AD7804/AD7808 from the controller. This can easily be
achieved by using opto-isolators which will provide isolation in
excess of 3 kV. The serial loading structure of the AD7804/
AD7808 makes it ideally suited for use in opto-isolated applications. Figure 41 shows an opto-isolated interface to the
AD7804/AD7808 where SDIN, CLKIN and FSIN are driven
from optocouplers. LDAC is hardwired low to reduce the number
of interface lines and this ensures that each DAC is updated following the sixteenth serial clock of a write cycle.
SDIN
SDIN
VDD
CLKIN
LDAC
VCC
1Y0
AD7808
1G
ENABLE
FSIN
1Y1
1A
SDIN
1Y2
CODED
ADDRESS
CLKIN
1B
LDAC
1Y3
74HC139
AD7808
DGND
FSIN
SDIN
POWER
CLKIN
+5V
REGULATOR
10mF
AD7808
VDD
FSIN
AVDD
10kV
CLKIN
VDD
DVDD
SDIN
REFOUT
CLKIN
CLKIN
AD7804/
AD7808
10kV
FSIN
REFIN
Figure 42. Decoding Multiple AD7808s Using the FSIN Pin
VOUTA
AD7805 As a Digitally Programmable Window Detector
VOUTB
VDD
10kV
A digitally programmable upper/lower limit detector using two
DACs in the AD7805 is shown in Figure 43. The upper and
lower limits for the test are loaded to DACs A and B that in
turn set the limits on the CMP04. If a signal at the VIN input is
not within the programmed window an LED will indicate the
fail condition. Only one limit detector is shown below but can
easily be adapted for a dual channel system by using the extra
DACs on the AD7805 and the two unused comparators on the
CMP04.
VOUTC
SDIN
VDD1
VOUTD
CLR
LDAC
DGND
LDAC
1 TO 10nF
FSIN
DATA
LDAC
0.1mF
AGND
Figure 41. AD7804/AD7808 Opto-Isolated Interface
+5V
10mF
0.1mF
Decoding Multiple AD7808s
The FSIN pin on the AD7808s can be used in applications to
decode a number of DACs. In this application all DACs in the
system receive the same serial clock and serial data, but only the
FSIN to one of the DACs will be active at any one time allowing
access to eight channels in this thirty-two channel system. The
74HC139 is used as a 2- to 4-line decoder to address any of the
DACs in the system. To prevent timing errors from occurring
the enable input should be brought to its inactive state while the
coded address inputs are changing state. Figure 42 shows a
system decoding multiple AD7808s in a multichannel system.
0.01mF
AVDD
DVDD
COMP
1kV
PASS
1/2
CMP04
VOUTA
0.01mF
PASS/
FAIL
AD7805
D9
DVDD
1kV
FAIL
VIN
D0
VOUTB
MODE
CS
WR
VOUTC
1/6
74HC05
VOUTD
CLR
LDAC
DGND
AGND
Figure 43. Digitally Programmable Window Detector
–24–
REV. A
AD7804/AD7805/AD7808/AD7809
Low Cost, Two-Channel Mixer Using AD7805, SSM2164 and
OP275
Dual External Reference Input Capability
It is possible to operate the AD7804/AD7805/AD7808/AD7809
with two externally applied references. Figure 45 shows the
connections for the AD7804. Reference one, the AD589, is
connected to the REFIN pin of the part; the second reference,
the AD780, is used to overdrive the internal VDD/2 reference
which is provided at the COMP pin of the device. With the
circuit shown in Figure 45 it is possible to configure two of the
channels for operation with the AD780 2.5 V reference and the
other two with the AD589 1.23 V reference. The channel control register allows the user to select the reference for the individual channels.
The SSM2164 is a quad voltage controlled amplifier (VCA)
with 120 dB of gain control range. Each VCA in the package is
a current in, current out device with a –33 mV/dB voltage control input port. Figure 44 shows a basic application circuit
which can be used to implement a low cost stereo, two channel
mixer. A 30 kΩ resistor converts the input voltage to an input
current for the VCA. The 500 Ω resistor and 560 pF capacitor
on the input are added to ensure stable operation of the
SSM2164. The IOUT pin of the SSM2164 should be maintained
at virtual ground and thus the OP275 is operated in its inverting
mode. Its wide bandwidth, high slew rate and low power make it
ideal for a current to voltage converter. A 30 kΩ feedback resistor is chosen to match the input resistor and thus give unity gain
for a zero volt control voltage input. The 100 pF capacitors
reduce high frequency noise and can be increased to reduce the
low pass cutoff frequency for further noise reduction. The
AD7805 in the circuit is used to control the attenuation of the
VCA, this application circuit only gives attenuation. The voltage
output from the AD7805 provides a low impedance drive to the
SSM2164 so attenuation can be controlled accurately. With a
5 V VDD and a VBIAS of VDD/2 the AD7805 has an LSB size of
approximately 4.5 mV. Therefore, the attenuation can be controlled with a resolution of 0.136 dB/bit and thus 750 codes are
required to provide the full 100 dB of attenuation.
+5V
10mF
0.1mF
0.1mF
6.8kV
VIN
VO
AD780
GND
AVDD DVDD
COMP
REFIN
0.01mF
AD589
AD7804
FSIN
SERIAL
INTERFACE
SDIN
CLKIN
DVDD
REFOUT
VOUTA
VOUTB
CLR
VOUTC
LDAC
VOUTD
DGND AGND
Figure 45. Two Externally Applied References
+5V
VIN2
10mF
0.1mF
30kV
VIN1
30kV
100pF
0.01mF
AVDD
DVDD
COMP
560pF
560pF
0.01mF
MODE
DVDD
100pF
VC3
30kV
IN4
+15V
1/2
OP275
VC4
VOUT D
AGND
–15V
IN3
CLR
DGND
VOUT A
VC2
VOUT B
VOUTC
LDAC
SSM2164
500V
500V
560pF
560pF
30kV
–15V
30kV
Figure 44. Low Cost, Two-Channel Mixer
–25–
VOUT B
–V
VIN3 VIN4
REV. A
1/2
OP275
IN2
CS
WR
+15V
VC1
VOUT A
D0
+V
30kV
IN1
AD7805
D9
+15V
500V
500V
–15V
AD7804/AD7805/AD7808/AD7809
PAGE INDEX
(AD7804/AD7808 SERIAL INTERFACE PART)
PAGE INDEX
(AD7805/AD7809 PARALLEL INTERFACE PART)
Topic
Page No.
Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3
Timing Information
Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . 6
Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Terminology
Relative Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Differential Nonlinearity . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Bias Offset Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gain Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Zero-Scale Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Digital-to-Analog Glitch Impulse . . . . . . . . . . . . . . . . . . . . 9
Digital Feedthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Digital Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Analog Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power Supply Rejection Ratio . . . . . . . . . . . . . . . . . . . . . . 9
Interface Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
System Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Channel Control Register . . . . . . . . . . . . . . . . . . . . . . . . . 11
SUB DAC Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power-Up Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Clear Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power-Down and Standby Functions . . . . . . . . . . . . . . . . . 16
LDAC Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Analog Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Transfer Functions
Pictorial View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Twos Complement (Main DAC) . . . . . . . . . . . . . . . . . . . 16
Twos Complement (Sub DAC) . . . . . . . . . . . . . . . . . . . . 17
Complete Channel Transfer Function . . . . . . . . . . . . . . . 17
Offset Binary (Main DAC) . . . . . . . . . . . . . . . . . . . . . . . . 18
Offset Binary (Sub DAC) . . . . . . . . . . . . . . . . . . . . . . . . . 19
Grounding and Layout Techniques . . . . . . . . . . . . . . . . . . . 20
Reference Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Typical Performance Characteristics . . . . . . . . . . . . . . . . . . 21
Microprocessor Interfacing
ADSP-2101/ADSP-2103 . . . . . . . . . . . . . . . . . . . . . . . . . 22
68HC11/68L11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
80C51/80L51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Applications
Opto-Isolated Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Decoding Multiple ICs . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Outline Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 28
Topic
Page No.
Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3
Timing Information
Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . 6
Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Terminology
Relative Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Differential Nonlinearity . . . . . . . . . . . . . . . . . . . . . . . . . 9
Bias Offset Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gain Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Zero-Scale Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Digital-to-Analog Glitch Impulse . . . . . . . . . . . . . . . . . . . 9
Digital Feedthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Digital Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Analog Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power Supply Rejection Ratio . . . . . . . . . . . . . . . . . . . . . 9
Interface Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
System Control Registers . . . . . . . . . . . . . . . . . . . . . . . . 14
Channel Control Register . . . . . . . . . . . . . . . . . . . . . . . . 14
Power-Up Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Clear Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power-Down and Standby Functions . . . . . . . . . . . . . . . . 16
LDAC Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Analog Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Transfer Functions
Pictorial View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Twos Complement (Main DAC) . . . . . . . . . . . . . . . . . . 16
Twos Complement (Sub DAC) . . . . . . . . . . . . . . . . . . . 17
Complete Channel Transfer Function . . . . . . . . . . . . . . 17
Offset Binary (Main DAC) . . . . . . . . . . . . . . . . . . . . . . . 18
Offset Binary (Sub DAC) . . . . . . . . . . . . . . . . . . . . . . . . 19
Grounding and Layout Techniques . . . . . . . . . . . . . . . . . . 20
Reference Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Typical Performance Characteristics . . . . . . . . . . . . . . . . . 21
Microprocessor Interfacing
ADSP-2101/ADSP-2103 . . . . . . . . . . . . . . . . . . . . . . . . 23
TMS32020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8051/8088 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Applications
Programmable Window Detector . . . . . . . . . . . . . . . . . . 24
Low Cost Two-Channel Mixer . . . . . . . . . . . . . . . . . . . 25
Dual External Reference Input Capability . . . . . . . . . . . 25
Outline Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 28
–26–
REV. A
AD7804/AD7805/AD7808/AD7809
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Plastic DIP (N-28)
Plastic DIP (N-16)
28
0.840 (21.33)
0.745 (18.93)
15
0.580 (14.73)
0.485 (12.32)
PIN 1
1
14
1.565 (39.70)
1.380 (35.10)
9
1
8
0.210 (5.33)
MAX
0.150
(3.81)
MIN
0.200 (5.05)
0.125 (3.18)
0.100
(2.54)
BSC
0.070 (1.77)
MAX
0.280 (7.11)
0.240 (6.10)
0.060 (1.52)
0.015 (0.38)
PIN 1
0.060 (1.52)
0.015 (0.38)
0.250
(6.35)
MAX
0.022 (0.558)
0.014 (0.356)
16
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.022 (0.558)
0.014 (0.356)
SEATING
PLANE
0.325 (8.25)
0.300 (7.62) 0.195 (4.95)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
0.070 (1.77) SEATING
0.045 (1.15) PLANE
0.100
(2.54)
BSC
0.625 (15.87)
0.600 (15.24)
0.195 (4.95)
0.125 (3.18)
SOIC (R-16)
0.015 (0.381)
0.008 (0.204)
28
14
1
0.1043 (2.65)
0.0926 (2.35)
0.7125 (18.10)
0.6969 (17.70)
8
0.0192 (0.49)
0.0138 (0.35)
0.0500 (1.27)
BSC
0.0125 (0.32)
0.0091 (0.23)
0.0118 (0.30)
0.0040 (0.10)
0.0500
(1.27)
BSC
0.0291 (0.74)
x 45 °
0.0098 (0.25)
8°
0°
0.0500 (1.27)
0.0157 (0.40)
SSOP (RS-28)
28
15
0.212 (5.38)
0.205 (5.207)
0.311 (7.9)
0.301 (7.64)
PIN 1
1
14
0.407 (10.34)
0.397 (10.08)
REV. A
1
PIN 1
0.4193 (10.65)
0.3937 (10.00)
PIN 1
0.008 (0.203)
0.002 (0.050)
9
15
0.2992 (7.60)
0.2914 (7.40)
0.0118 (0.30)
0.0040 (0.10)
16
0.07 (1.78)
0.066 (1.67)
8°
0°
0.009 (0.229)
0.005 (0.127)
1. LEAD NO. 1 IDENTIFIED BY A DOT.
2. LEADS WILL BE EITHER TIN PLATED OR SOLDER DIPPED
IN ACCORDANCE WITH MIL-M-38510 REQUIREMENTS
0.0256 (0.65)
BSC
0.015 (0.38)
0.010 (0.25)
0.03 (0.762)
0.022 (0.558)
–27–
0.4193 (10.65)
0.3937 (10.00)
SOIC (R-28)
0.2992 (7.60)
0.2914 (7.40)
0.4133 (10.50)
0.3977 (10.00)
0.1043 (2.65)
0.0926 (2.35)
0.0291 (0.74)
x 45°
0.0098 (0.25)
8°
0.0192 (0.49)
0°
SEATING 0.0125 (0.32)
0.0138 (0.35) PLANE
0.0091 (0.23)
0.0500 (1.27)
0.0157 (0.40)
AD7804/AD7805/AD7808/AD7809
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
TQFP (ST-44B)
0.047 (1.20)
MAX
13
24
0.018 (0.45)
12
1
0.472 (12.00) SQ
0.030 (0.75)
0.280 (7.11)
0.240 (6.10)
PIN 1
33
23
34
1.275 (32.30)
1.125 (28.60)
0.015
(0.38)
MIN
0.210
(5.33)
MAX
22
SEATING
PLANE
0.325 (8.25)
0.300 (7.62)
0.195 (4.95)
0.115 (2.93)
0.160 (4.06)
0.115 (2.92)
0.022 (0.558)
0.014 (0.356)
0.070 (1.77)
0.045 (1.15)
0.100 (2.54)
BSC
0.394
(10.0)
SQ
TOP VIEW
(PINS DOWN)
0.130
(3.30)
MIN
0.015 (0.381)
0.008 (0.203)
SEATING
PLANE
44
C2107a–1–12/98
Plastic DIP (N-24)
12
1
11
0.006 (0.15)
0.002 (0.05)
0.04134 (1.05)
0.0374 (0.95)
0.031 (0.80)
BSC
0.018 (0.45)
0.012 (0.30)
SOIC (R-24)
0.614 (15.6)
0.598 (15.2)
24
13
0.299 (7.6) 0.419 (10.65)
0.291 (7.4) 0.394 (10.00)
1
12
0.012 (0.3)
0.004 (0.1)
0.0500 (1.27)
BSC
0.104 (2.65)
0.093 (2.35)
0.03 (0.75)
0.01 (0.25)
88
0.019 (0.49) SEATING 0.013 (0.32) 08
0.014 (0.35) PLANE
0.009 (0.25)
0.0500 (1.27)
0.0157 (0.40)
PRINTED IN U.S.A.
PIN 1
–28–
REV. A