NT1+/INF2 ® Power Management Module for ISDN NT1+ Rev. 01 Type Vi Vo Po +/-40V 4.5W 180<VI1<264Vrms +5V 720mW -22V 900mW 40<Vi2<120 Vdc -50V 100mW -130V 700mW NT1+/INF2 PRODUCT VIEW FEATURES COMBINED AC+DC CONVERTER FOR ISDN NT1+ APPLICATION Uo INTERFACE (DC) AND MAIN (AC) INPUTS TO ENABLE NPM (Normal Power Mode) AND RPM (Restricted Power Mode) CONDITIONS INPUT FILTER TO MEET EMC REQUIREMENTS ORDERING NUMBER: GS-NT1+/INF2 INTERNAL RELAY FUNCTION FOR Vo1 POLARITY REVERSE 5 INSULATED MAIN OUTPUTS ANALOG OUTPUTS EMERGENCY CONDITION PROGRAMMABLE VIA EXTERNAL COMMAND, TTL COMPATIBLE, 1mA SINK CURRENT PEAK INPUT OVERVOLTAGE WITHSTANDING U-INTERFACE ACCORDING TO ETR 080 WITH EXTERNAL CAPACITOR </= 2.2 uF INPUT FUSE ON AC MAIN INPUT S-INTERFACE ACCORDING TO ETS 300 012 INPUTS TO OUTPUTS INSULATION AUXILIARY LOGIC OUTPUT TTL-COMPATIBLE FOR NPM/RPM MODE INDICATION (EM SIGNAL & GREEN LED). 3mA OUTPUT SOURCE CURRENT SAFETY COMPLIANCE ACCORDING TO EN60950 MECHANICAL 96x58x26.6 DIMENSIONS (LxWxH): AUXILIARY LOGIC OUTPUT TTL-COMPATIBLE FOR U-INTERFACE DETECTION (RED LED). 3mA OUTPUT SOURCE CURRENT June 2000 1/7 NT1+/INF2 DESCRIPTION The NT1+/INF2 Power Management Module is a comprehensive solution for ISDN-NT1 "Plus" (Network Termination Basic Access type Plus) equipment, combining both AC-DC and DC-DC functions. This version is suitable for Infineon ISDN U/S chip set. The NT1+ Power Management Module (NT1+ PMM) provide the NT1+ equipment with all necessary supply voltages as well as control signals to operate in the different operating modes, typically the Normal Power Mode (NPM) and the Restricted Power Mode (RPM). Connected to the main, Input 1 is the AC input power to the NT1+ PMM, source of the whole necessary power in normal operating mode, namely in NPM. Input 2 is the DC power source when in RPM, therefore to connect to the U-Interface. When the main is available (230 Vac in this version) NT1+ PMM operate in Normal Power Mode, therefore it supply +40V (output 1) to the S-Interface being the output power 4.5 W. Output 2 delivers 5V (up to 720mW) for the logics and output 3 delivers -22V (up to 900 mW). Out voltage 4 is -50V with 100 mW output power. Last, output 5 delivers -130V and the output power can reach peaks of 700 mW. When the main is missing, the module remains active but only in Restricted Power Mode (RPM). The only power source in RPM is the Input 2, the U-Interface (Vi2). Therefore in RPM the following condition apply to outputs 1 and 2: output 1 reverses the voltage (it becomes -40V) and the maximum power Pout is reduced to 420 mW. P2max is reduced to 450 mW typically, however the output power available at outputs 2,3,4,5 mainly depend on input power available from the "U Interface" Vi2, therefore subject of variation as per local application and regulation. In RPM it is also possible to set a different "emergency condition" setting HIGH the auxiliary input 3 (analog emergency input, Vin3). In this case Pout1 is reduced to 25mW, voltage level being -40V. The following tables give you details of the various parameters in the 3 different operating modes, namely NPM, RPM with Vi3 LOW, RPM with Vi3 HIGH. 2/7 Availability of the input AC main is also acknowledged by a specific auxiliary output (out 6, "EM signal"), a TTL-compatible signal set HIGH (to logic level "1") when the main is available and LOW when the AC main is missing. The presence of the "U" is optionally acknowledged by an other auxiliary output (out 7, RED LED) that is HIGH only when Vin2 > 40V. The NT1+ PMM provides double insulation (3000 Vrms) between the inputs (1 and 2), and among the input 1 and all the outputs. Basic insulation exists among Out1 and all other outputs. The other outputs (including the 2 auxiliary outputs) and the input 3, share the same common ground. Double insulation (2000 Vrms) is provided among Input 2 (DC "U") and all outputs. The NT1+ Power Management Module operate in the range -10 to +70 oC, storage temperatures in the range -40 to +85 oC are allowed. NT1+/INF2 ELECTRICAL CHARACTERISTICS when in NPM (Tamb=25oC, unless otherwise specified.) NPM Standard Condition: Vin1 = 180 to 264 Vrms Vin2 = 40 to 120 Vdc Symbol Parameter Vi1 AC Input Voltage 1 Vi2 DC Input Voltage 2 fi Test Condition Min. Typ. Max. Unit 180 264 Vrms any polarity 40 120 Vdc Vi1 Input Frequency Vi1 = 230 Vrms 43 56 Hz Vi1st Start up Input 1 voltage Output parameters Standard Condition 175 Vrms Pi1 Input 1 Apparent Power NPM Standard Condition 15 VA Vi2nd Start up Input 2 voltage Output parameters as per Std. Condition 40 Vdc Vo1 Output Voltage 1 Standard condition 34 40 42 V Vo2 Output Voltage 2 Standard condition 4.75 5 5.25 V Vo3 Output Voltage 3 Standard condition -21 -22 -25 V Vo4 Output Voltage 4 Standard condition -48 -50 -65 V Vo5 Output Voltage 5 Standard condition -125 -130 -165 V Vo6 Auxiliary Output 6 (EM) Standard condition 3.75 5 5.25 V Vo7 Auxiliary Output 7 (red LED) Standard condition 3.75 5 5.25 V Vor1,3,4,5 Output Ripple voltage 1,3,4,5 Standard condition BW: 0-20 MHz 100 mVrms Vor2 Output Ripple voltage 2 Standard condition BW: 0-20 MHz 30 mVrms Po1 Output Power 1 Std. condition according to ETS300 012, E5.1.5, E5.1.6, E5.1.7 (n=4) 4.5 W Po2 Output Power 2 Standard condition 720 mW Po3 Output Power 3 Standard condition 900 mW Po4 Output Power 4 Standard condition 100 mW Po5 Output Power 5 During 1 s, 40% of the time during the ring period at the analog interface. The output is current limited at 2.5 mA +/- 0.2 mA, with 100uF capacitor 700 mW Vi1th NPM => threshold Vi1 Output parameters as per Standard Condition 160 Vrms Ttr Transition time transition NPM => RPM and vice versa according to ETS300 012, E5.1.3 (n=4) 5 ms Vi1pk Input 1 Transient overvoltage t = 10/700 us as per 1TR9 Dec. 96 Vi1pk Input 1 Transient overvoltage common mode test ETS300 047-5p5.6 Vi1pk RPM mode as per NPM 2000 V 2500 V Input 1 Transient overvoltage impulse transfer from main according to 2500 ETS300 047-5p5.7.1 V Vo1pk Output 1 Transient overvoltage t = 1,2/50 us V Vis Insulation Voltage Input 1 to outputs and input 1 to input 2, t=60s reinforced insulation as per 3000 EN60950 V Vist Insulation Voltage Input 1 to outputs t=10/700 us (pulse) V according to 500 4000 th Hold-up time Vin = 180 Vrms Standard Condition 20 ms MTBF Mean Time Before Failure Ground Fixed, MIL-HDBK-217E 1 Mh Top Oper. Ambient Temperature -10 +70 o C 3/7 NT1+/INF2 ELECTRICAL CHARACTERISTICS when in RPM (Tamb=25oC, unless otherwise specified.) RPM Standard Condition: Vin1 < 100 Vrms Vin2 = 40 to 120 Vdc Vin3 = LOW Symbol Parameter Test Condition Vi1 AC Input Voltage 1 Vi2 DC Input Voltage 2 any polarity Vi2nd Start up Input 2 voltage Output parameters as per Std. Condition Min. Typ. 40 Max. Unit 100 Vrms 120 Vdc 48 Vdc Vo1 Output Voltage 1 Standard condition -34 -40 -42 V Vo2 Output Voltage 2 Standard condition 4.75 5 5.25 V Vo3 Output Voltage 3 Standard condition -21 -22 -25 V Vo4 Output Voltage 4 Standard condition -48 -50 -65 V Vo5 Output Voltage 5 Standard condition -125 -130 -165 V Vo6 Auxiliary Output 6 (EM) Standard condition 3.75 5 5.25 V Vo7 Auxiliary Output 7 (red LED) Standard condition 3.75 5 5.25 V Vor1,3,4,5 Output Ripple voltage 1,3,4,5 Standard condition BW: 0-20 MHz 100 mVrms Vor2 Output Ripple voltage 2 Standard condition BW: 0-20 MHz 30 mVrms Po1 Output Power 1 Std condition according to ETS300 012, E5.1.1, E5.1.4.1, E5.1.4.2, E5.1.5.3 (n=4) 420 mW Po2 Output Power 2 Standard condition 450 mW Po3 Output Power 3 Standard condition tbd mW Po4 Output Power 4 Standard condition tbd mW Standard condition tbd mW Po5 Output Power 5 Vi1st RPM => threshold Ttr Transition time transition NPM => RPM and vice versa according to ETS300 012, E5.1.3 (n=4) Vi1pk Input 1 Transient overvoltage t = 10/700 us as per 1TR9 Dec. 96 2000 V Vi1pk Input 1 Transient overvoltage common mode test according to ETS300 2500 047-5p5.6 V Vi1pk Input 1 Transient overvoltage impulse transfer from main according to 2500 ETS300 047-5p5.7.1 V Vo1pk Output 1 overvoltage t = 1,2/50 us V Vis Insulation Voltage Input 1 to outputs and input 1 to input 2, t=60s reinforced insulation as per 3000 EN60950 V Vist Insulation Voltage Input 1 to outputs t=10/700 us (pulse) 4000 V th Hold-up time Vin = 180 Vrms Standard Condition 20 ms MTBF Mean Time Before Failure Ground Fixed, MIL-HDBK-217E 1 Mhou rs Top Oper. Ambient Temperature Tstg 4/7 NPM mode Vi1 Output parameters as per Standard Condition Transient Storage Temperature Range 175 Vrms 5 ms 500 -10 -40 +70 o C +85 o C NT1+/INF2 ELECTRICAL CHARACTERISTICS when in RPM (Tamb=25oC, unless otherwise specified.) RPM Standard Condition: Vin1 < 100 Vrms Vin2 = 40 to 120 Vdc Vin3 =HIGH Symbol Parameter Test Condition Vi1 AC Input Voltage 1 Vi2 DC Input Voltage 2 any polarity Vi2nd Start up Input 2 voltage Output parameters as per Std. Condition Min. Typ. Max. Unit 0 100 Vrms 40 120 Vdc 40 Vdc Vo1 Output Voltage 1 Standard condition -34 -40 -42 V Vo2 Output Voltage 2 Standard condition 4.75 5 5.25 V Vo3 Output Voltage 3 Standard condition -21 -22 -25 V Vo4 Output Voltage 4 Standard condition -48 -50 -65 V Vo5 Output Voltage 5 Standard condition -125 -130 -165 V Vo6 Auxiliary Output 6 (EM) Standard condition 0 1.25 V Vo7 Auxiliary Output 7 (red LED) Standard condition 3.75 5.25 V Vor1,3,4,5 Output Ripple voltage 1,3,4,5 Standard condition BW: 0-20 MHz 100 mVrms Vor2 Output Ripple voltage 2 Standard condition BW: 0-20 MHz 30 mVrms Po1 Output Power 1 Standard condition 25 mW Po2 Output Power 2 Standard condition 450 mW Po3 Output Power 3 Standard condition tbd mW Po4 Output Power 4 Standard condition tbd mW Po5 Output Power 5 Standard condition tbd mW Vi1st RPM => threshold Ttr Transition time transition NPM => RPM and vice versa according to ETS300 012, E5.1.3 (n=4) Vi1pk Input 1 Transient overvoltage t = 10/700 us as per 1TR9 Dec. 96 2000 V Vi1pk Input 1 Transient overvoltage common mode test according to ETS300 2500 047-5p5.6 V Vi1pk Input 1 Transient overvoltage impulse transfer from main according to 2500 ETS300 047-5p5.7.1 V Vo1pk Output 1 overvoltage t = 1,2/50 us V Vis Insulation Voltage Input 1 to outputs and input 1 to input 2, t=60s reinforced insulation as per 3000 EN60950 V Vist Insulation Voltage Input 1 to outputs t=10/700 us (pulse) 4000 V th Hold-up time Vin = 180 Vrms Standard Condition 20 ms 1 Mhou rs NPM mode Vi1 Output parameters as per Standard Condition Transient Ground Fixed, MIL-HDBK-217E 5 175 Vrms 5 ms 500 MTBF Mean Time Before Failure Top Oper. Ambient Temperature -10 +70 o C Tstg Storage Temperature Range -40 +85 o C 5/7 NT1+/INF2 NT1+ Power Management Module TOP VIEW (dimensions in mm PIN CONFIGURATION Input 1 (230 Vac) applies to the Vac INPUT CONNECTOR Pin No Signal Pin No Signal 1 Output 1 return 10 Output 7 (RED LED) 2 Output 1 (+/- 40 V) 11 N.C. 3 PS Signal 12 GND, Common return for output 2,3,4,5,6,7, Input 3 4 Output 3 (-22 V) 13 Vi2 Input Voltage 2, Vdc (any polarity) 5 Output 6 (EM, Green LED) 14 Vi2 Input Voltage 2, Vdc (any polarity 6 Output 2 (+5 V) 15 Vi1 Input Voltage 1, VAC 7 Vin 3, Analog Emergency Input 3 16 Vi1 Input Voltage 1, VAC 8 Output 4 (-50 V) 17 N.C. 9 Output 5 (-130 V) 18 N.C. 6/7 NT1+/INF2 NT1+ Power Management Module SIDE VIEW (dimensions in mm) Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 2000 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com 7/7