LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS SLOS068D – JUNE 1976 – REVISED SEPTEMBER 2001 D D D D D 1OUT 1IN– 1IN+ GND 1 8 2 7 3 6 4 5 VCC 2OUT 2IN– 2IN+ LM158, LM158A . . . FK PACKAGE (TOP VIEW) NC 1OUT NC V CC+ NC D D, JG, P, OR PW PACKAGE (TOP VIEW) Wide Range of Supply Voltages: – Single Supply . . . 3 V to 30 V (LM2904 and LM2904Q . . . 3 V to 26 V) or – Dual Supplies Low Supply-Current Drain Independent of Supply Voltage . . . 0.7 mA Typ Common-Mode Input Voltage Range Includes Ground, Allowing Direct Sensing Near Ground Low Input Bias and Offset Parameters: – Input Offset Voltage . . . 3 mV Typ A Versions . . . 2 mV Typ – Input Offset Current . . . 2 nA Typ – Input Bias Current . . . 20 nA Typ A Versions . . . 15 nA Typ Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage . . . ±32 V (LM2904 and LM2904Q . . . ±26 V) Open-Loop Differential Voltage Amplification . . . 100 V/mV Typ Internal Frequency Compensation NC 1IN– NC 1IN+ NC 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC 2OUT NC 2IN– NC NC GND NC 2IN+ NC D NC – No internal connection description These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 30 V (3 V to 26 V for the LM2904 and LM2904Q), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be more easily implemented in single-supply-voltage systems. For example, these devices can be operated directly from the standard 5-V supply used in digital systems and easily provide the required interface electronics without additional ±5-V supplies. The LM2904Q is manufactured to demanding automotive requirements. The LM158 and LM158A are characterized for operation over the full military temperature range of –55°C to 125°C. The LM258 and LM258A are characterized for operation from –25°C to 85°C, the LM358 and LM358A from 0°C to 70°C, and the LM2904 and LM2904Q from –40°C to 125°C. logic diagram (each amplifier) IN+ IN– + – OUT Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS SLOS068D – JUNE 1976 – REVISED SEPTEMBER 2001 AVAILABLE OPTIONS PACKAGED DEVICES TA VIO(max) AT 25°C SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (JG) 7 mV LM358D — 3 mV — — 5 mV LM258D 0°C to 70°C –25°C 25°C to 85°C 40°C to 125°C –40°C –55°C 55°C to 125°C 3 mV 7 mV PLASTIC DIP (P) TSSOP (PW) — LM358P LM358PW — LM358AP — — — LM258P — — — — LM258AP — LM2904D — — LM2904P LM2904PW LM2904QD — — — — 5 mV — LM158FK LM158JG — — 2 mV — LM158AFK LM158AJG — — The D package is available taped and reeled. Add the suffix R to the device type (e.g., LM358DR). The PW package is only available taped and reeled. schematic (each amplifier) VCC+ ≈6-µA Current Regulator ≈6-µA Current Regulator ≈100-µA Current Regulator OUT IN– ≈50-µA Current Regulator IN+ GND (or VCC–) To Other Amplifier COMPONENT COUNT Epi-FET Diodes Resistors Transistors Capacitors 2 POST OFFICE BOX 655303 1 2 7 51 2 • DALLAS, TEXAS 75265 LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS SLOS068D – JUNE 1976 – REVISED SEPTEMBER 2001 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† LM158, LM158A LM258, LM258A LM358, LM358A Supply voltage, VCC (see Note 1) Differential input voltage, VID (see Note 2) LM2904 LM2904Q 32 26 V ±32 ±26 V V Input voltage, VI (either input) –0.3 to 32 –0.3 to 26 Duration of output short circuit (one amplifier) to ground at (or below) 25°C free-air temperature (VCC ≤ 15 V) (see Note 3) Unlimited Unlimited Package thermal impedance, θJA (see Note 4) D package 97 P package 85 85 149 149 PW package Continuous total power dissipation UNIT 97 °C See Dissipation Rating Table Operating free-air free air temperature range, range TA LM158, LM158A –55 to 125 LM258, LM258A –25 to 85 LM358, LM358A 0 to 70 LM2904, LM2904Q °C –40 to 125 °C Case temperature for 60 seconds FK package 260 Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds JG package 300 300 °C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds D, P, or PW package 260 260 °C –65 to 150 °C Storage temperature range, Tstg –65 to 150 † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages and VCC specified for measurement of IOS, are with respect to the network ground terminal. 2. Differential voltages are at IN+ with respect to IN–. 3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. 4. The package thermal impedance is calculated in accordance with JESD 51-7. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING TA = 85°C POWER RATING TA = 125°C POWER RATING FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW JG 1050 mW 8.4 mW/°C 672 mW 546 mW 210 mW POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS SLOS068D – JUNE 1976 – REVISED SEPTEMBER 2001 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER LM158 LM258 TA‡ TEST CONDITIONS† MIN VIO Input offset voltage aV Average temperature coefficient of input offset voltage IO IIO Input offset current αIIO Average temperature coefficient of input offset current IIB Input bias current VICR Common-mode input voltage range VOH High-level g output voltage VCC = 5 V to MAX, VIC = VICR( i ), ICR(min) VO = 1.4 V VO = 1 1.4 4V IOS ICC Supply current (two amplifiers) 7 25°C 2 30 2 100 Full range 10 25°C –20 10 –150 –20 25°C VCC–1.5 VCC–1.5 RL ≥ 10 kΩ 25°C 26 26 RL ≥ 10 kΩ Full range 27 Full range 28 5 27 20 –250 V V 28 5 20 mV 50 Full range 25 VCC = 5 V to MAX, VIC = VICR(min) 25°C 70 80 65 80 dB VCC = 5 V to MAX 25°C 65 100 65 100 dB f = 1 kHz to 20 kHz 25°C 120 dB VCC = 15 V,, VID = 1 V,, VO = 0 25°C –20 Full range –10 25°C 10 Full range 5 100 25°C 12 V/mV VID = –1 V, VO = 200 mV VCC at 5 V, GND at –5 V, VO = 0 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load 25 nA 25°C VCC = 15 V,, VID = –1 V,, VO = 15 V 100 nA pA/°C –500 RL ≥ 2 kΩ Full range 50 150 –300 RL = 2 kΩ µV/°C 7 0 to VCC–2 Common-mode rejection ratio Short-circuit output current 7 0 to VCC–2 CMRR 3 9 Full range VCC = 15 V, VO = 1 V to 11 V V, RL = ≥ 2 kΩ MAX 7 Full range VCC = 5 V to MAX Large-signal differential voltage amplification UNIT TYP§ mV Full range 0 to VCC–1.5 AVD Output current 5 0 to VCC–1.5 RL ≤ 10 kΩ IO 3 MIN 25°C Low-level output voltage VO1/VO2 MAX Full range VOL Supply-voltage rejection ratio (∆VDD/∆VIO) Crosstalk attenuation TYP§ Full range VO = 1 1.4 4V VCC = MAX kSVR 25°C LM358 15 120 –30 –20 –30 –10 20 10 mA 20 5 30 12 µA 30 25°C ±40 ±60 ±40 ±60 Full range 0.7 1.2 0.7 1.2 Full range 1 2 1 2 mA mA † All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM 2904 and 30 V for others. ‡ Full range is –55°C to 125°C for LM158, –25°C to 85°C for LM258, 0°C to 70°C for LM358, and –40°C to 125°C for LM2904 and LM2904Q. § All typical values are at TA = 25°C. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS SLOS068D – JUNE 1976 – REVISED SEPTEMBER 2001 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) TEST CONDITIONS† PARAMETER LM2904 LM2904Q TA‡ MIN VIO Input offset voltage aV Average temperature coefficient of input offset voltage IO IIO Input offset current αIIO Average temperature coefficient of input offset current IIB Input bias current VICR VCC = 5 V to MAX,, VIC = VICR(min), VO = 1.4 V VO = 1 1.4 4V High level output voltage High-level Low-level output voltage 7 Full range 10 Full range 7 25°C 2 10 25°C –20 50 0 to VCC–1.5 Full range 0 to VCC–2 nA pA/°C –250 –500 25°C mV µV/°C 300 Full range VCC = 5 V to MAX nA V 25°C RL ≥ 10 kΩ 25°C VCC = MAX VOL 3 Full range RL ≥ 2 kΩ VOH MAX Full range VO = 1 1.4 4V Common mode input voltage range Common-mode 25°C UNIT TYP§ RL = 2 kΩ Full range VCC–1.5 26 RL ≥ 10 kΩ Full range 23 24 25°C 25 100 Full range 15 RL ≤ 10 kΩ Full range V 5 20 mV AVD Large-signal differential g g voltage amplification VCC = 15 V,, VO = 1 V to 11 V,, RL = ≥ 2 kΩ CMRR Common-mode rejection ratio VCC = 5 V to MAX, VIC = VICR(min) 25°C 50 80 dB kSVR Supply-voltage rejection ratio (∆VDD/∆VIO) VCC = 5 V to MAX 25°C 65 100 dB VO1/VO2 Crosstalk attenuation f = 1 kHz to 20 kHz 25°C 120 dB VCC = 15 V V, VID = 1 V V, VO = 0 IO Output current IOS Short-circuit output current ICC Supply current (two amplifiers) 1 V, V VO = 15 V VCC = 15 V V, VID = –1 25°C –20 Full range –10 25°C 10 Full range 5 V/mV –30 mA 20 µA VID = –1 V, VO = 200 mV VCC at 5 V, GND at –5 V, VO = 0 25°C 30 25°C ±40 ±60 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load Full range 0.7 1.2 Full range 1 2 mA mA † All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM 2904 and 30 V for others. ‡ Full range is –55°C to 125°C for LM158, –25°C to 85°C for LM258, 0°C to 70°C for LM358, and –40°C to 125°C for LM2904 and LM2904Q. § All typical values are at TA = 25°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS SLOS068D – JUNE 1976 – REVISED SEPTEMBER 2001 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage aV Average temperature coefficient of input offset voltage IO IIO Input offset current αIIO Average temperature coefficient of input offset current IIB Input bias current VICR VOH Common-mode input voltage range Hi h l l High-level out ut voltage output VCC = 5 V to 30 V, VIC = VICR( i ), ICR(min) VO = 1.4 V VO = 1 1.4 4V VO = 1 1.4 4V Output current IOS Short-circuit output current ICC Supply current (two amplifiers) 4 7 15 25°C 2 10 2 15 30 Full range 10 25°C –15 30 200 10 –50 –15 –100 0 to VCC–1.5 0 to VCC–1.5 Full range 0 to VCC–2 0 to VCC–2 VCC–1.5 26 27 Full range 28 5 27 20 100 200 –80 –100 25°C Full range nA pA/°C nA V 28 5 50 µV/°C V 20 mV 25°C 50 100 Full range 25 25°C 70 80 70 80 dB 25°C 65 100 65 100 dB V/mV 25 f = 1 kHz to 20 kHz 25°C VCC = 15 V,, VID = 1 V,, VO = 0 25°C –20 Full range –10 25°C 10 Full range 5 VID = –1 V, VO = 200 mV VCC at 5 V, GND at –5 V VO = 0 25°C 12 25°C ±40 ±60 ±40 ±60 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V No load Full range 0.7 1.2 0.7 1.2 Full range 1 2 1 2 VCC = 15 V,, VID = –1 V,, VO = 15 UNIT 3 15* Full range Common-mode rejection ratio 2 MAX 7 RL ≥ 10 kΩ CMRR LM258A TYP§ Full range RL = 2 kΩ VCC = 15 V, VO = 1 V to 11 V V, RL = ≥ 2 kΩ MIN mV VCC–1.5 26 Large-signal differential voltage amplification IO 4 25°C AVD VO1/VO2 Full range RL ≥ 2 kΩ RL ≤ 10 kΩ MAX 2 Full range Low-level output voltage Supply-voltage rejection ratio (∆VDD/∆VIO) Crosstalk attenuation LM158A TYP§ 25°C VCC = 30 V VCC = 30 V MIN Full range VOL kSVR TA‡ TEST CONDITIONS† 120 –30 120 –60 –20 –30 dB –60 –10 20 10 mA 20 5 30 12 µA 30 mA mA *On products compliant to MIL-PRF-38535, this parameter is not production tested. † All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM2904 and 30 V for others. ‡ Full range is –55°C to 125°C for LM158A, –25°C to 85°C for LM258A, and 0°C to 70°C for LM358A. § All typical values are at TA = 25°C. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS SLOS068D – JUNE 1976 – REVISED SEPTEMBER 2001 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS† VIO Input offset voltage VCC = 5 V to 30 V,, VIC = VICR(min), VO = 1.4 V aV Average temperature coefficient of input offset voltage IO IIO Input offset current αIIO Average temperature coefficient of input offset current IIB Input bias current VICR VO = 1 1.4 4V VOL High-level output voltage Low-level output voltage LM358A TYP§ MAX 2 3 25°C Full range 5 Full range 7 20 25°C 2 30 75 Full range 10 300 25°C –15 –100 Full range 0 to VCC–1.5 Full range 0 to VCC–2 25°C VCC = 30 V –200 25°C VCC = 30 V RL ≥ 2 kΩ VOH MIN Full range VO = 1 1.4 4V Common mode input voltage range Common-mode TA‡ Full range VCC–1.5 26 RL ≥ 10 kΩ Full range 27 28 25°C 25 100 Full range 15 Full range VCC = 15 V,, VO = 1 V to 11 V,, RL = ≥ 2 kΩ mV µV/°C nA pA/°C nA V RL = 2 kΩ RL ≤ 10 kΩ UNIT V 5 20 mV AVD Large-signal g g differential voltage amplification CMRR Common-mode rejection ratio 25°C 65 80 dB kSVR Supply-voltage rejection ratio (∆VDD/∆VIO) 25°C 65 100 dB VO1/VO2 Crosstalk attenuation 120 dB f = 1 kHz to 20 kHz VCC = 15 V,, VID = 1 V,, VO = 0 IO Output current IOS Short-circuit output current ICC Supply current (two amplifiers) VCC = 15 V,, VID = –1 V,, VO = 15 V 25°C 25°C –20 Full range –10 25°C 10 Full range 5 –30 V/mV –60 mA 20 µA VID = –1 V, VO = 200 mV VCC at 5 V, GND at –5 V VO = 0 25°C 30 25°C ±40 ±60 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V No load Full range 0.7 1.2 Full range 1 2 mA mA † All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM2904 and 30 V for others. ‡ Full range is –55°C to 125°C for LM158A, –25°C to 85°C for LM258A, and 0°C to 70°C for LM358A. § All typical values are at TA = 25°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2001, Texas Instruments Incorporated