PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 3.3V Boost LVDS High-Speed Differential Line Drivers and Receivers Product Features Product Description Signaling Rates >660 Mbps (330 MHz) The PI90LVB179, PI90LVB180, PI90LVB050, and PI90LVB051 are differential line drivers and receivers (transceivers) that are similar to the IEEE 1596.3 SCI and ANSI/TIA/EIA-644 LVDS standards (the difference is that the driver output current is doubled). This modification enables true half-duplex operation with more than one LVDS driver or with two line transmission resistors over a 50-ohm differential transmission line. These devices use low-voltage differential signaling (LVDS) to achieve data rates in excess of 660 Mbps while being less susceptible to noise than single-ended transmission. Single 3.3V Power Supply Design Driver: ±350mV Differential Swing into a 50-ohm load Propogation Delay of 1.5ns Typ. Low Voltage TTL (LVTTL) Inputs are 5V Tolerant Driver is High Impedance when Disabled or VCC < 1.5V Receiver: Accepts ±50mV (min.) Differential Swing with up to 2.0V ground potential difference Propagation Delay of 3.3ns Typ. Low Voltage TTL (LVTTL) Outputs Open, Short, and Terminated Fail Safe Industrial Temperature Operating Range: 40°C to 85°C The drivers translate a low-voltage TTL/CMOS input into a lowvoltage (350mV typical) differential output signal into a 50-ohm load. The receivers translate a differential 350mV input signal to a 3V CMOS output level. Driver section can be independently set to a power-down & high-impedance output mode with the DEN pin (active HIGH). Receiver section is controlled by the REN* pin (active LOW). Package Options: SOIC, TSSOP, MSOP Applications Bus-Terminal ESD >12kV Applications include point-to-point and multidrop baseband data transmission over a controlled impedance media of approximately 50 ohms. These include intra-system connections via printed circuit board traces or cables, hubs and routers for data communications; PBXs, switches, repeaters & base stations for telecommunications and other applications such as digital cameras, printers and copiers. PI90LVB050 PI90LVB179 DIN1 VCC 1 ROUT DIN 2 3 GND 4 8 8-Pin U, W 7 6 5 RIN+ RIN– DOUT– DOUT+ DIN RIN1– RIN1+ ROUT1 REN* ROUT2 RIN2+ RIN2– GND DOUT+ DOUT- ROUT RIN+ RIN- 1 2 3 4 5 6 7 8 16 15 14 16-Pin 13 L, W 12 11 10 9 VCC DIN1 DOUT1+ DOUT1– DEN DOUT2– DOUT2+ DIN2 DEN DIN2 ROUT1 REN* ROUT2 PI90LVB180 1 2 3 4 5 6 7 14 13 14-Pin 12 11 L, W 10 9 8 DOUT1DOUT2+ DOUT2RIN1+ RIN1RIN2+ RIN2- PI90LVB051 DIN1 NC ROUT REN* DEN DIN GND GND DOUT1+ VCC VCC RIN+ RIN– DOUT– DOUT+ NC DIN DEN DOUT+ DOUT- RIN1– RIN1+ ROUT1 DEN1 ROUT2 RIN2+ RIN2– GND REN* ROUT RIN+ RIN- 1 2 3 4 5 6 7 8 16 15 14 16-Pin 13 L, W 12 11 10 9 VCC DIN1 DOUT1+ DOUT1– DEN2 DOUT2– DOUT2+ DIN2 DOUT1+ DOUT1- DEN1 RIN1+ ROUT1 DIN2 RIN1DOUT2+ DOUT2- DEN2 RIN2+ ROUT2 RIN2- 1 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Function Tables Pin Descriptions PI90LVB179 Receiver Inputs Output Name VID = VRIN+ VRIN ROUT DIN VID ≥ 50mV H DOUT+ Non- inverting driver output pins 50mV < VID < 50mV ? DOUT+ Inverting driver output pins VID ≤ 50mV L open H PI90LVB179 Driver Input Output DIN DOUT+ DOUT L L H H H L open L H ROUT TTL/CMOS receiver output pins RIN+ Non- inverting receiver input pins RIN Inverting receiver input pins VID Input Differential Signal Voltage GND Ground pin VCC Positive power supply pin, +3.3V ±10% Supply Voltage (VCC) ....................................... 0.5V to +4.0V Driver Input Voltage (DIN) ........................... 0.3V to (Vcc + 0.3V) Output Voltage (DOUT+, DOUT-) ...................0.3V to +3.9V Short Circuit Duration (DOUT+, DOUT-) ............ Continuous Enable Input Voltage (DEN) ................ 0.3V to (VCC + 0.3V) Receiver Input Voltage (RIN+, RIN-) ........................... 0.3V to +3.9V) Output Voltage (ROUT) ....................... 0.3V to (VCC + 0.3V) Enable Input Voltage (REN*) .............. 0.3V to (VCC + 0.3V) Storage Temperature Range ..........................65°C to +150°C Lead Temperature Range Soldering (4s) ....................... +260°C Maximum Junction Temperature ................................... +150°C ESD Rating ..................................................................... >12kV Output VID = VRIN+ VRIN REN* ROUT VID ≥ 50mV L H 50mV < VID < 50mV L ? VID ≤ 50mV L L open L H X H Z Recommended Operating Conditions PI90LVB180/PI90LVB050/PI90LVB051 Drivers Inputs TTL/CMOS driver input pins Absolute Maximum Ratings PI90LVB180/ PI90LVB050/PI90LVB051 Receivers Inputs De s cription Output DIN DEN DOUT+ DOUT L H L H H H H L open H L H X L Z Z M in. Typ. M ax. Units Supply Voltage (VCC) 3 3.3 3.6 V High Level Input Voltage, VIH 2 0.8 Low Level Input Voltage, VIL Magnitude of Differential Input Voltage VID 0.1 0.6 Common- mode Input Voltage, VIC (Fig 5) |VID| /2 2.4 |VID| /2 VCC 0.8 Operating Free Air Temperature TA Notes: H = High Level, L = Low Level, ? = Indeterminate, Z = High-Impedance, X = Dont Care 2 40 85 PS8540A °C 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 Electrical Characteristics (Over recommended operating conditions unless otherwise noted). Typ. M ax. 14 19.5 Driver and receiver enabled. No receiver load, Driver RL = 50 ohms 12.5 16.4 Driver enabled, Receiver disabled, RL = 50 ohms 10.2 14 Driver disabled, Receiver enabled, No load 3.4 5 Disabled 0.8 1.5 Driver and receivers enabled. No receiver loads, Driver RL = 50 ohms 25 30 14.8 20 6 8 Disabled 0.8 1.3 Drivers enabled, No receiver loads, Driver RL = 50 ohms 27 33 Drivers disabled, No loads 6.5 8.8 M in. Typ. M ax. 247 380 475 Parame te r Te s t Condition PI90LVB179 PI90LVB180 ICC* Supply Current PI90LVB050 M in. No receiver load, Driver RL = 50 ohms Drivers enabled, Receivers disabled, RL = 50 ohms Drivers disabled, Receivers enabled, No loads PI90LVB051 Units mA All typical values are at 25°C with a 3.3V supply *ICC measured with all TTL input. VIN = VCC or GND. Driver Electrical Characteristics (Over recommended operating conditions unless otherwise noted). Parame te r Te s t Conditions VOD Differential output voltage magnitude ∆VOD Change in differential output voltage magnitude between logic states VOC(SS) Steady- state common- mode output voltage ∆VOC(SS) Change in steady- state common- mode output voltage between logic states VOC(PP) Peak- to- peak common- mode output voltage IIH High- level input current IIL Low- level input current IOS Short- circuit output current IOZ High- impedance output current IO(OFF) Power- off output current CIN Input capacitance RL = 50 ohms See Figures 1 and 2 50 1.125 See Figure 3 DE DIN DE DIN 50 1.25 50 1.375 50 50 150 0.5 20 2 20 0.5 10 2 10 VOY or VOZ = 0V 11 15 VOD = 0V 12 15 VIH = 5V VIL = 0.8V VOD = 600mV ±1 VO - 0V or VCC ±1 VCC = 0V, VO = 3.6V ±1 7 3 Units mV V mV µA mA µA pF PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Receiver Electrical Characteristics (Over recommended operating conditions unless otherwise noted). Parame te r Te s t Conditions M in. Typ. M ax. VITH+ Positive- going differential input voltage threshold VITH Negative- going differential input voltage threshold VOH High- level output voltage IOH = 8mA VOL Low- level output voltage IOL = 8mA II Input current (RIN+ or RIN) II (OFF) Power- off input current (RIN+ or RIN) VCC = 0 ±20 IH High- level input current (enables) VIH = 2V ±10 IL Low- level input current (enables) VIL = 0.8V ±10 IOZ High- impedance output current VO = 0 or 5V ±10 CI Input capacitance See Figures 5 & Table 1 VI = 0 VI = 2.4V 50 50 2.4 Units mV V 0.4 2 11 1.2 3 V 20 6.6 µA pF All typical values are at 25°C with a 3.3V supply Driver Switching Characteristics (Over recommended operating conditions unless otherwise noted). Parame te r Te s t Conditions M in. Typ. M ax. tPLH Propagation delay time, low- to- high- level output 1.7 2.6 tPHL Propagation delay time, lhigh- to- low- level output 1.7 2.6 tr Differential output signal rise time 0.4 0.8 tf Differential output signal fall time 0.4 0.8 tsk(p) Pulse skew (tPHL tPLH) 250 360 90 160 RL = 50 ohms CL = 10pF See Figure 2 skew tsk(o) Channel- to- channel output tsk(pp) Part- part- part skew* * tPZH Propagation delay time, high- impedance- to- high- level output tPZL Propagation delay time, high- impedance- to- low- level output tPHZ Propagation delay time, high- level- to- high- impedance output tPLZ Propagation delay time, low- level- to- high- impedance output Units ns ps 0.9 See Figure 7 3 5 3 5 3 5 3 5 ns All typical values are at 25°C with a 3.3V supply tsk(o): the maximum delay time difference between drivers on the same device. ** tsk(pp): magnitude of difference in propagation delay times between any specific terminals of two devices (all things being equal) 4 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 Receiving Switching Characteristics (Over recommended operating conditions unless otherwise noted). Parame te r Te s t Conditions M in. Typ. M ax. tPLH Propagation delay time, low- to- high- level output 2 3.0 tPHL Propagation delay time, lhigh- to- low- level output 2.1 3.0 tsk(pp)** Part- part- part skew* * tsk(p) Pulse skew (tPHL tPLH) tsk(o) Channel- to- channel skew tr O utput signal rise time 1.0 1.5 tf O utput signal fall time 1.2 1.8 tPZH Propagation delay time, high- level- to- high- impedance output 1.7 2.3 tPZL Propagation delay time, low- level- to- low- impedance output 4.5 5.7 tPHZ Propagation delay time, high- impedance- to- high- level output 2.5 3.2 tPLZ Propagation delay time, low- impedance- to- high- level output 6.0 7.8 CL = 10pF See Figure 6 See Figure 7 Units ns 1.0 300 750 60 ps ns All typical values are at 25°C with a 3.3V supply. ** tsk(pp) is magnitude of difference in propagation delay times between any specific terminals of two devices (all things being equal). Parameter Measurement Information DEN DOD+ DOUT+ II DIN VOD Driver VOD+VOD+ 2 VOD+ DOUT– VOC VI VOD– Figure 1. Driver Voltage and Current Definitions 5 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Parameter Measurement Information Driver (continued) DEN DOUT+ 50Ω ±1% VOD DIN DOUT– CL = 10 pF (2 Places) 2V 1.4 V 0.8 V DIN tPHL tPLH 100% 80% VOD(H) Output 0V VOD(L) 20% 0% tf tr NOTE A: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns . CL includes instrumentation and fixture capacitance within 0.06 mm of the D.U.T. Figure 2. Test Circuit, Timing, and Voltage Definitions for the Differential Output Signal 25 Ω, ±1% (2 Places) DEN 3V DOUT+ DIN 0V DOUT– VOC VOC(PP) CL = 10pF (2 Places) VOC(SS) VOC NOTE A: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns . CL includes instrumentation and fixture capacitance within 0.06 mm of the D.U.T. The measurement of VOC(PP) is made on test equipment with a –3 dB bandwidth of at least 300 MHz. Figure 3. Test Circuit and Definitions for the Driver Common-Mode Output Voltage 6 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 Parameter Measurement Information (continued) Driver (continued) 25Ω ±1% (2 Places) DOUT+ DIN at 0.8V or 2V DOUT– DEN 1.2 V CL =10pF (2 Places) VOD+ VOD– 2V 1.4 V 0.8 V DEN VOD+ or VOD– tPZH ~1.4 V 1.25 V 1.2 V DIN at 2V and input to DEN 1.2 V 1.15 V ~1 V DIN at 0.8 V and input to DEN tPHZ VOD– or VOD+ tPZL tPLZ NOTE A: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1ns, pulse repetition rate (PRR) = 0.5 Mpps, pulse width = 500 ± 10 ns. CL includes instrumentation and fixture capacitance within 0.06mm of the D.U.T. Figure 4. Enable and Disable Timing Circuit and Definitions 7 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Parameter Measurement Information (continued) Receiver RIN+ VIRIN++VIRIN– ROUT VID 2 VIRIN+ VIC VIRIN– RIN– VO Figure 5. Receiver Voltage Definitions Table 1. Receiver Minimum and Maximum Input Threshold Test Voltages APPLIED VOLTAGES (V) VIRIN+ VIRIN+ RESULTING DIFFERENTIAL INPUT VOLTAGE (mV) RESULTING COMMONMODE INPUT VOLTAGE (V) VID VIC 1.2 1.225 1.175 50 1.175 1.225 –50 1.2 2.375 2.325 50 2.35 2.325 2.375 –50 2.35 0.1 0 50 0.05 –50 0.05 0 0.05 1.5 0.9 600 1.2 0.9 1.5 –600 1.2 2.4 1.8 600 2.1 1.8 2.4 –600 2.1 0.6 0 600 0.3 0 0.6 –600 0.3 8 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 Parameter Measurement Information (continued) Receiver (continued) VID VIRIN+ CL 10pF VIRIN– VO VIRIN+ 1.4 V VIRIN– 1V VID 0.4 V 0V – 0.4 V tPHL VO tPLH VOH 2.4 V 1.4 V 0.4 V VOL tf tr NOTE A: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns. CL includes instrumentation and fixture capacitance within 0.06 m of the D.U.T. Figure 6. Timing Test Circuit and Waveforms 9 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Parameter Measurement Information (continued) Receiver (continued) 1.2 V RIN– 500 Ω RIN+ Inputs REN* CL 10 pF + – VO VTEST NOTE A: All input pulses are supplied by a genertor having the following characteristics: tr or tf ≤ 1ns, pulse repetition rate (PRR) = 0.5 Mpps, pulse wide = 500 ±10ns. CL includes instrumentation and fixture capacitance within 0.06m of the D.U.T. 2.5 V VTEST RIN* 1V 2V REN* 1.4 V 0.8 V tPZL tPZL tPLZ 2.5 V ROUT 1.4 V VOL +0.5 V VOL VTEST 0V RIN+ 1.4 V REN* 2V 1.4 V 0.8 V tPZH ROUT tPZH tPHZ VOH VOH –0.5 V 1.4 V 0V Figure 7. Enable/Disable Time Test Circuit and Waveforms 10 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 8-Pin SOIC W Package 8 .149 .157 3.78 3.99 .0099 .0196 1 .189 .196 .016 .026 0.406 0.660 0.25 x 45˚ 0.50 .0075 .0098 0-8˚ 4.80 5.00 0.19 0.25 0.40 .016 1.27 .050 .053 .068 1.35 1.75 SEATING PLANE REF .050 BSC 1.27 .2284 .2440 5.80 6.20 .0040 0.10 .0098 0.25 .013 0.330 .020 0.508 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 8-Pin Mini Small Outline U Package (MSOP) 11 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 14-Pin SOIC (150 Mil) W Package 14 .149 .157 .0099 .0196 3.78 3.99 0.25 x 45˚ 0.50 .0075 .0098 0-8˚ 1 0.41 1.27 .336 .344 8.55 8.75 .0155 .026 0.393 0.660 .053 .068 SEATING PLANE .050 BSC 1.27 .016 .050 .2284 .2440 5.80 6.20 1.35 1.75 REF 0.19 0.25 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS .0040 0.10 .0098 0.25 .013 .020 0.330 0.508 14-Pin TSSOP (4.4mm wide) L Package 14 0.004 0.09 0.008 0.20 0.169 0.177 4.3 4.5 0.45 0.75 0.240 0.264 1 0.193 0.201 4.90 5.10 6.1 6.7 0.047 1.20 max. SEATING PLANE 0.0256 typical 0.65 0.018 0.030 0.007 0.012 0.19 0.30 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 0.002 0.05 0.006 0.15 12 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123 16-Pin SOIC (150 Mil) W Package 16 .149 .157 3.78 3.99 .0099 .0196 0.25 x 45˚ 0.50 1 .0075 .0098 0-8˚ .386 .393 9.80 10.00 0.41 1.27 .053 .068 .0155 .0260 0.393 0.660 REF 1.35 1.75 .016 .050 .2284 .2440 5.80 6.20 SEATING PLANE .050 BSC 1.27 0.19 0.25 .0040 0.10 .0098 0.25 .013 .020 0.330 0.508 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 16-Pin TSSOP (4.4mm wide) L Package 16 .169 .177 4.3 4.5 1 .193 .201 4.9 5.1 .004 .008 .047 max. 1.20 0.45 .018 0.75 .030 SEATING PLANE .0256 BSC 0.65 .007 .012 .002 .006 0.09 0.20 .252 BSC 6.4 0.05 0.15 X.XX DENOTES CONTROLLING X.XX DIMENSIONS IN MILLIMETERS 0.19 0.30 13 PS8540A 08/07/01 PI90LVB179/PI90LVB180/ PI90LVB050/PI90LVB051 3.3V Boost LVDS High-Speed Differential Line Drivers & Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Ordering Information Part Pin - Package Te mpe rature PI90LVB179W 8- SOIC 40°C to +85°C PI90LVB180W 14- SOIC 40°C to +85°C PI90LVB050W 16- SOIC 40°C to +85°C PI90LVB051W 16- SOIC 40°C to +85°C PI90LVB179U 8- MSO P 40°C to +85°C PI90LVB180L 14- TSSOP 40°C to +85°C PI90LVB050L 16- TSSO P 40°C to +85°C PI90LVB051L 16- TSSOP 40°C to +85°C Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com 14 PS8540A 08/07/01