ETC TMS320C6203CGNZ300

TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
D
D
D
D
D
Signal Processor (DSP) – TMS320C62x
– 4-, 3.33-ns Instruction Cycle Time
– 250-, 300-MHz Clock Rate
– Eight 32-Bit Instructions/Cycle
– 2000, 2400 MIPS
C6203B and C6202/02B GLS Ball Grid Array
(BGA) Packages are Pin-Compatible With
the C6204 GLW BGA Package†
VelociTI Advanced Very-Long-InstructionWord (VLIW) C62x DSP Core
– Eight Highly Independent Functional
Units:
– Six ALUs (32-/40-Bit)
– Two 16-Bit Multipliers (32-Bit Result)
– Load-Store Architecture With 32 32-Bit
General-Purpose Registers
– Instruction Packing Reduces Code Size
– All Instructions Conditional
Instruction Set Features
– Byte-Addressable (8-, 16-, 32-Bit Data)
– 8-Bit Overflow Protection
– Saturation
– Bit-Field Extract, Set, Clear
– Bit-Counting
– Normalization
7M-Bit On-Chip SRAM
– 3M-Bit Internal Program/Cache
(96K 32-Bit Instructions)
– 4M-Bit Dual-Access Internal Data
(512K Bytes)
– Organized as Two 256K-Byte Blocks
for Improved Concurrency
32-Bit External Memory Interface (EMIF)
– Glueless Interface to Synchronous
Memories: SDRAM or SBSRAM
– Glueless Interface to Asynchronous
Memories: SRAM and EPROM
– 52M-Byte Addressable External Memory
Space
D Four-Channel Bootloading
D
D
D
D
D
D
D
D
D
D
D
D
Direct-Memory-Access (DMA) Controller
With an Auxiliary Channel
Flexible Phase-Locked-Loop (PLL) Clock
Generator
32-Bit Expansion Bus (XBus)
– Glueless/Low-Glue Interface to Popular
PCI Bridge Chips
– Glueless/Low-Glue Interface to Popular
Synchronous or Asynchronous
Microprocessor Buses
– Master/Slave Functionality
– Glueless Interface to Synchronous FIFOs
and Asynchronous Peripherals
Three Multichannel Buffered Serial Ports
(McBSPs)
– Direct Interface to T1/E1, MVIP, SCSA
Framers
– ST-Bus-Switching Compatible
– Up to 256 Channels Each
– AC97-Compatible
– Serial-Peripheral Interface (SPI)
Compatible (Motorola)
Two 32-Bit General-Purpose Timers
IEEE-1149.1 (JTAG‡)
Boundary-Scan-Compatible
352-Pin BGA Package (GNZ) (C6203C only)
384-Pin BGA Package (GLS) (C6203B only)
384-Pin BGA Package (GNY)
[C6203B and C6203C]
0.12-µm/6-Level Metal Process (C6203C)
0.15-µm/5-Level Metal Process (C6203B)
– CMOS Technology
3.3-V I/Os, 1.2-V Internal (C6203C)
3.3-V I/Os, 1.5-V Internal (C6203B)
PRODUCT PREVIEW
D High-Performance Fixed-Point Digital
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
TMS320C62x, VelociTI, and C62x are trademarks of Texas Instruments.
Motorola is a trademark of Motorola, Inc.
All trademarks are the property of their respective owners.
† For more details, see the GLS BGA package bottom view.
‡ IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
Copyright  2001, Texas Instruments Incorporated
This document contains information on products in more than one phase
of development. The status of each device is indicated on the page(s)
specifying its electrical characteristics.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
1
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Table of Contents
signal transition levels . . . . . . . . . . . . . . . . . . . . . . . . . . 37
timing parameters and board routing analysis . . . . . . 38
PRODUCT PREVIEW
GNZ, GLS, and GNY BGA packages (bottom view) . . . . 2
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C62x device compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
functional and CPU (DSP core) block diagram . . . . . . . . . 8
CPU (DSP core) description . . . . . . . . . . . . . . . . . . . . . . . . 9
memory map summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DMA synchronization events . . . . . . . . . . . . . . . . . . . . . . . 12
interrupt sources and interrupt selector . . . . . . . . . . . . . . 13
signal groups description . . . . . . . . . . . . . . . . . . . . . . . . . . 14
signal descriptions development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
documentation support . . . . . . . . . . . . . . . . . . . . . . . . . . . .
clock PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
power-supply sequencing . . . . . . . . . . . . . . . . . . . . . . . . . .
absolute maximum ratings over operating case
temperature ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . .
recommended operating conditions . . . . . . . . . . . . . . . . .
electrical characteristics over recommended ranges
of supply voltage and operating case temperature . .
input and output clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
asynchronous memory timing . . . . . . . . . . . . . . . . . . . . . 42
synchronous-burst memory timing . . . . . . . . . . . . . . . . . 46
synchronous DRAM timing . . . . . . . . . . . . . . . . . . . . . . . . 48
HOLD/HOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
external interrupt timing . . . . . . . . . . . . . . . . . . . . . . . . . . 55
17
28
31
32
35
expansion bus synchronous FIFO timing . . . . . . . . . . . . 56
expansion bus asynchronous peripheral timing . . . . . . 58
expansion bus synchronous host-port timing . . . . . . . . 62
expansion bus asynchronous host-port timing . . . . . . . 68
XHOLD/XHOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . 70
36
36
multichannel buffered serial port timing . . . . . . . . . . . . . 72
36
JTAG test-port timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
parameter measurement information . . . . . . . . . . . . . . . . 37
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
DMAC, timer, power-down timing . . . . . . . . . . . . . . . . . . 84
GNZ, GLS, and GNY BGA packages (bottom view)
GNZ 352-PIN BALL GRID ARRAY (BGA) PACKAGE ( BOTTOM VIEW ) [C6203C only]
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
3
2
2
5
4
7
6
9
8
10
POST OFFICE BOX 1443
11 13 15 17 19 21 23 25
12 14 16 18 20 22 24 26
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
GNZ, GLS, and GNY BGA packages (bottom view) (continued)
GLS 384-PIN BGA PACKAGE ( BOTTOM VIEW ) [C6203B only]
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
PRODUCT PREVIEW
C
B
A
3
5
9
11 13 15 17 19 21
7
4
10 12 14 16 18 20 22
2
6
8
The C6203B and C6202/02B GLS BGA packages are pin-compatible with the C6204 GLW
package except that the inner row of balls (which are additional power and ground pins)
are removed for the C6204 GLW package.
1
These balls are NOT applicable for the C6204 devices 340-pin GLW BGA package.
GNY 384-PIN BGA PACKAGE ( BOTTOM VIEW )
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
3
1
2
5
4
9
7
6
8
POST OFFICE BOX 1443
10
11 13 15 17 19 21
12 14 16 18 20 22
• HOUSTON, TEXAS 77251–1443
3
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
description
The TMS320C6203B and TMS320C6203C devices are part of the TMS320C62x fixed-point DSP generation
in the TMS320C6000 DSP platform. The C62x DSP devices are based on the high-performance, advanced
VelociTI very-long-instruction-word (VLIW) architecture developed by Texas Instruments (TI), making these
DSPs an excellent choice for multichannel and multifunction applications.
The TMS320C62x DSP offers cost-effective solutions to high-performance DSP-programming challenges.
The TMS320C6203B/03C has a performance capability of up to 2400 MIPS at a clock rate of 300 MHz. The
C6203B/03C DSP possesses the operational flexibility of high-speed controllers and the numerical capability
of array processors. This processor has 32 general-purpose registers of 32-bit word length and eight highly
independent functional units. The eight functional units provide six arithmetic logic units (ALUs) for a high
degree of parallelism and two 16-bit multipliers for a 32-bit result. The C6203B/03C can produce two
multiply-accumulates (MACs) per cycle for a total of 600 million MACs per second (MMACS). The C6203B/03C
DSP also has application-specific hardware logic, on-chip memory, and additional on-chip peripherals.
PRODUCT PREVIEW
The C6203B/03C device program memory consists of two blocks, with a 256K-byte block configured as
memory-mapped program space, and the other 128K-byte block user-configurable as cache or
memory-mapped program space. Data memory for the C6203B/03C consists of two 256K-byte blocks of RAM.
The C6203B/03C device has a powerful and diverse set of peripherals. The peripheral set includes three
multichannel buffered serial ports (McBSPs), two general-purpose timers, a 32-bit expansion bus (XBus) that
offers ease of interface to synchronous or asynchronous industry-standard host bus protocols, and a glueless
32-bit external memory interface (EMIF) capable of interfacing to SDRAM or SBSRAM and asynchronous
peripherals.
The C62x devices have a complete set of development tools which includes: a new C compiler, an assembly
optimizer to simplify programming and scheduling, and a Windows debugger interface for visibility into source
code execution.
device characteristics
Table 1 provides an overview of the TMS320C6203C, TMS320C6203B, TMS320C6202/02B, and the
TMS320C6204 DSPs. The table shows significant features of each device, including the capacity of on-chip
RAM, the peripherals, the execution time, and the package type with pin count, etc. This data sheet primarily
focuses on the functionality of the TMS320C6203B/03C devices although it also identifies to the user the
pin-compatibility of the C6203B and C6202/02B GLS, and the C6204 GLW BGA packages. For the functionality
information on the TMS320C6202/02B devices, see the TMS320C6202, TMS320C6202B Fixed-Point Digital
Signal Processors data sheet (literature number SPRS104). For the functionality information on the
TMS320C6204 device, see the TMS320C6204 Fixed-Point Digital Signal Processor data sheet (literature
number SPRS152). And for more details on the C6000 DSP part numbering, see Figure 4.
TMS320C6000 and C6000 are trademarks of Texas Instruments.
Windows is a registered trademark of the Microsoft Corporation.
4
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
device characteristics (continued)
Table 1. Characteristics of the Pin-Compatible DSPs
P i h l
Peripherals
Internal Program
Memory
C6203B
C6203C
EMIF
√
√
DMA
4-Channel With
Throughput Enhancements
4-Channel With
Throughput Enhancements
Expansion Bus
√
√
McBSPs
3
3
32-Bit Timers
2
2
Size (Bytes)
384K
384K
Organization
Block 0:
256K-Byte Mapped
Program
Block 1:
128K-Byte Cache/Mapped
Program
Block 0:
256K-Byte Mapped
Program
Block 1:
128K-Byte Cache/Mapped
Program
Size (Bytes)
Internal Data Memory
512K
2 Blocks:
Four 16-Bit Banks per
Block
50/50 Split
Organization
CPU ID +
CPU Rev ID
Control Status Register (CSR.[31:16])
Frequency
MHz
Cycle Time
ns
512K
2 Blocks:
Four 16-Bit Banks per
Block
50/50 Split
0x0003
0x0004
250, 300
300
3.33 ns (6203B-300)
4 ns (6203B-250)
PRODUCT PREVIEW
HARDWARE FEATURES
3.33 ns (6203C-300)
1.5
Voltage
Core (V)
1.7 (GLS pkg only)
I/O (V)
3.3
CLKIN frequency multiplier [Bypass (x1),
x4, x6, x7, x8, x9, x10, and x11]
PLL Options
x12 multiplier option (6203C only)
27 x 27 mm
BGA Packages
Bypass (x1), x4, x6, x7,
x8, x9, x10, and x11
(Both GLS/GNY Pkgs)
–
12
1.2
3.3
x1, x4, x8, x12
(GNZ Pkg)
x1, x4, x6, x8, x12
(GNY Pkg)
352-pin GNZ
18 x 18 mm
384-pin GLS
–
18 x 18 mm
384-pin GNY (2.x, 3.x only)
384-pin GNY
16 x 16 mm
–
–
0.15 µm
0.12 µm
AI
PP
Process Technology
µm
Product Status
Product Preview (PP)
Advance Information (AI)
Production Data (PD)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
5
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
device characteristics (continued)
Table 1. Characteristics of the Pin-Compatible DSPs (Continued)
HARDWARE FEATURES
EMIF
DMA
Peripherals
Peri
herals
√
√
2
32-Bit Timers
2
2
2
256K
64K
PRODUCT PREVIEW
256K
Block 0:
128K-Byte Mapped
Program
Block 1:
128K-Byte
Cache/Mapped
Program
Organization
6
Block 0:
128K-Byte Mapped
Program
Block 1:
128K-Byte
Cache/Mapped
Program
128K
2 Blocks:
Four 16-Bit Banks per
Block
50/50 Split
Organization
MHz
BGA Packages
4-Channel
4-Channel With
Throughput
Enhancements
3
Frequency
PLL Options
√
4-Channel With
Throughput
Enhancements
√
Control Status Register
(CSR.[31:16])
Voltage
C6204
3
CPU ID +
CPU Rev ID
Cycle Time
√
McBSPs
Size (Bytes)
Internal Data Memory
C6202B
√
Expansion Bus
Size (Bytes)
Internal Program
Memory
C6202
64K
2 Blocks:
Four 16-Bit Banks per
Block
50/50 Split
0x0002
0x0003
0x0003
200, 250
250
200
4 ns (6202-250)
5 ns (6202-200)
ns
128K
2 Blocks:
Four 16-Bit Banks per
Block
50/50 Split
1 Block:
64K-Byte
Cache/Mapped
Program
Core (V)
1.8
I/O (V)
3.3
4 ns (6202B-250)
5 ns (6204-200)
1.5
1.5
3.3
3.3
x1, x4, x8, x10
(GJL Pkg)
CLKIN frequency multiplier
[Bypass (x1), x4, x6, x7, x8,
x9, x10, and x11]
x1, x4
(Both Pkgs)
27 x 27 mm
352-pin GJL
–
–
18 x 18 mm
384-pin GLS
384-pin GNY
340-pin GLW
16 x 16 mm
–
–
288-pin GHK
0.18 µm
0.15 µm
0.15 µm
PD
PP
PP
Process Technology
µm
Product Status
Product Preview (PP)
Advance Information (AI)
Production Data (PD)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
All PLL Options
(GLS Pkg)
x1, x4
(Both Pkgs)
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
C62x device compatibility
The TMS320C6202, C6202B, C6203B, C6203C, and C6204 devices are pin-compatible; thus, making new
system designs easier and providing faster time to market. The following list summarizes the C62x DSP
device characteristic differences:
D Core Supply Voltage (1.8 V versus 1.5 V versus 1.2 V)
The C6202 device core supply voltage is 1.8 V while the C6202B, C6203B, C6204 devices have core supply
voltages of 1.5 V and the C6203C device has a core supply voltage of 1.2 V.
D PLL Options Availability
Table 1 identifies the available PLL multiply factors [e.g., CLKIN x1 (PLL bypassed), x4, etc.] for each of the
C62x DSP devices. For additional details on the PLL clock module and specific options for the
C6203B/03C devices, see the Clock PLL section of this data sheet.
And for additional details on the PLL clock module and specific options for the C6204 device, see the Clock
PLL section of the TMS320C6204 Fixed-Point Digital Signal Processor data sheet (literature number
SPRS152).
D On-Chip Memory Size
The C6202/02B, C6203B/03C, and C6204 devices have different on-chip program memory and data
memory sizes (see Table 1).
D McBSPs
The C6202, C6202B, C6203B, and C6203C devices have three McBSPs while the C6204 device has two
McBSPs on-chip.
For a more detailed discussion on migration concerns, and similarities/differences between the C6202,
C6202B, C6203B, C6203C, and C6204 devices, see the How to Begin Development and Migrate Across the
TMS320C6202/6202B/6203B/6204 DSPs application report (literature number SPRA603).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
7
PRODUCT PREVIEW
For additional details on the PLL clock module and specific options for the C6202/02B devices, see the
Clock PLL section of the TMS320C6202, TMS320C6202B Fixed-Point Digital Signal Processors data sheet
(literature number SPRS104).
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
functional and CPU (DSP core) block diagram
C6203B/03C Digital Signal Processors
SDRAM or
SBSRAM
Program
Access/Cache
Controller
32
SRAM
External Memory
Interface (EMIF)
ROM/FLASH
Internal Program Memory
2 Blocks Program/Cache
(384K Bytes)
I/O Devices
C62x CPU (DSP Core)
Timer 0
Instruction Fetch
Timer 1
PRODUCT PREVIEW
Instruction Dispatch
Data Path A
I/O Devices
HOST CONNECTION
Master /Slave
TI PCI2040
Power PC
683xx
960
Data Path B
A Register File
Multichannel
Buffered Serial
Port 1
.L1
.S1
.M1 .D1
Test
B Register File
.D2 .M2
.S2
In-Circuit
Emulation
.L2
Multichannel
Buffered Serial
Port 2
DMA
Bus
Interrupt
Selector
Synchronous
FIFOs
Control
Logic
Instruction Decode
Multichannel
Buffered Serial
Port 0
Framing Chips:
H.100, MVIP,
SCSA, T1, E1
AC97 Devices,
SPI Devices,
Codecs
Control
Registers
Peripheral Control Bus
Interrupt
Control
Internal Data
Memory
(512K Bytes)
Data
Access
Controller
32
Expansion
Bus (XBus)
32-Bit
Direct Memory
Access Controller
(DMA)
(See Table 1)
PLL
(x1, x4, x6, x7, x8,
x9, x10, x11, x12)†
PowerDown
Logic
Boot Configuration
† For additional details on the PLL clock module and specific options for the C6203B/03C devices, see Table 1 and the Clock PLL section of this
data sheet.
8
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
CPU (DSP core) description
The CPU features two sets of functional units. Each set contains four units and a register file. One set contains
functional units .L1, .S1, .M1, and .D1; the other set contains units .D2, .M2, .S2, and .L2. The two register files
each contain 16 32-bit registers for a total of 32 general-purpose registers. The two sets of functional units, along
with two register files, compose sides A and B of the CPU [see the functional and CPU (DSP core) block diagram
and Figure 1]. The four functional units on each side of the CPU can freely share the 16 registers belonging to
that side. Additionally, each side features a single data bus connected to all the registers on the other side, by
which the two sets of functional units can access data from the register files on the opposite side. While register
access by functional units on the same side of the CPU as the register file can service all the units in a single
clock cycle, register access using the register file across the CPU supports one read and one write per cycle.
Another key feature of the C62x CPU is the load/store architecture, where all instructions operate on registers
(as opposed to data in memory). Two sets of data-addressing units (.D1 and .D2) are responsible for all data
transfers between the register files and the memory. The data address driven by the .D units allows data
addresses generated from one register file to be used to load or store data to or from the other register file. The
C62x CPU supports a variety of indirect addressing modes using either linear- or circular-addressing modes
with 5- or 15-bit offsets. All instructions are conditional, and most can access any one of the 32 registers. Some
registers, however, are singled out to support specific addressing or to hold the condition for conditional
instructions (if the condition is not automatically “true”). The two .M functional units are dedicated for multiplies.
The two .S and .L functional units perform a general set of arithmetic, logical, and branch functions with results
available every clock cycle.
The processing flow begins when a 256-bit-wide instruction fetch packet is fetched from a program memory.
The 32-bit instructions destined for the individual functional units are “linked” together by “1” bits in the least
significant bit (LSB) position of the instructions. The instructions that are “chained” together for simultaneous
execution (up to eight in total) compose an execute packet. A “0” in the LSB of an instruction breaks the chain,
effectively placing the instructions that follow it in the next execute packet. If an execute packet crosses the
256-bit-wide fetch-packet boundary, the assembler places it in the next fetch packet, while the remainder of the
current fetch packet is padded with NOP instructions. The number of execute packets within a fetch packet can
vary from one to eight. Execute packets are dispatched to their respective functional units at the rate of one per
clock cycle and the next 256-bit fetch packet is not fetched until all the execute packets from the current fetch
packet have been dispatched. After decoding, the instructions simultaneously drive all active functional units
for a maximum execution rate of eight instructions every clock cycle. While most results are stored in 32-bit
registers, they can be subsequently moved to memory as bytes or half-words as well. All load and store
instructions are byte-, half-word, or word-addressable.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
9
PRODUCT PREVIEW
The CPU fetches VelociTI advanced very-long instruction words (VLIW) (256 bits wide) to supply up to eight
32-bit instructions to the eight functional units during every clock cycle. The VelociTI VLIW architecture
features controls by which all eight units do not have to be supplied with instructions if they are not ready to
execute. The first bit of every 32-bit instruction determines if the next instruction belongs to the same execute
packet as the previous instruction, or whether it should be executed in the following clock as a part of the next
execute packet. Fetch packets are always 256 bits wide; however, the execute packets can vary in size. The
variable-length execute packets are a key memory-saving feature, distinguishing the C62x CPU from other
VLIW architectures.
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
CPU (DSP core) description (continued)
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
Á ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
Á
Á ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
Á
Á ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Á ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
src1
.L1
src2
dst
long dst
long src
ST1
Data Path A
long src
long dst
dst
.S1
src1
dst
src1
PRODUCT PREVIEW
LD1
DA1
DA2
.D2
dst
src1
src2
src2
src1
dst
LD2
src2
.M2
src1
dst
src2
Data Path B
src1
dst
long dst
long src
.S2
ST2
long src
long dst
dst
.L2
src2
src1
32
8
src2
.D1
8
8
src2
.M1
Á
Á
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
Á
Register
File A
(A0–A15)
Á
Á
Á
Á
2X
1X
Á
Á
Á
Á
Register
File B
(B0–B15)
8
32
8
Á
Á
Á
Á
8
Figure 1. TMS320C62x CPU (DSP Core) Data Paths
10
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
Control
Register
File
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
memory map summary
Table 2 shows the memory map address ranges of the C6203B/03C device. The C6203B/03C device has the
capability of a MAP 0 or MAP 1 memory block configuration. These memory block configurations are set up at
reset by the boot configuration pins (generically called BOOTMODE[4:0]). For the C6203B/03C device, the
BOOTMODE configuration is handled, at reset, by the expansion bus module (specifically XD[4:0] pins). For
more detailed information on the C6203B/03C device settings, which include the device boot mode
configuration at reset and other device-specific configurations, see the Boot Configuration section and the Boot
Configuration Summary table of the TMS320C6000 Peripherals Reference Guide (literature number
SPRU190).
Table 2. TMS320C6203B/03C Memory Map Summary
BLOCK SIZE
(BYTES)
HEX ADDRESS RANGE
MAP 1
External Memory Interface (EMIF) CE0
Internal Program RAM
384K
0000_0000 – 0005_FFFF
EMIF CE0
Reserved
4M – 384K
0006_0000 – 003F_FFFF
EMIF CE0
EMIF CE0
12M
0040_0000 – 00FF_FFFF
EMIF CE1
EMIF CE0
4M
0100_0000 – 013F_FFFF
Internal Program RAM
EMIF CE1
384K
0140_0000 – 0145_FFFF
EMIF CE1
Reserved
4M – 384K
0146_0000 – 017F_FFFF
EMIF Registers
256K
0180_0000 – 0183_FFFF
DMA Controller Registers
256K
0184_0000 – 0187_FFFF
Expansion Bus (XBus) Registers
256K
0188_0000 – 018B_FFFF
McBSP 0 Registers
256K
018C_0000 – 018F_FFFF
McBSP 1 Registers
256K
0190_0000 – 0193_FFFF
Timer 0 Registers
256K
0194_0000 – 0197_FFFF
Timer 1 Registers
256K
0198_0000 – 019B_FFFF
Interrupt Selector Registers
512
019C_0000 – 019C_01FF
Power-Down Registers
256K – 512
019C_0200 – 019F_FFFF
Reserved
256K
01A0_0000 – 01A3_FFFF
McBSP 2 Registers
256K
01A4_0000 – 01A7_FFFF
Reserved
5.5M
01A8_0000 – 01FF_FFFF
EMIF CE2
16M
0200_0000 – 02FF_FFFF
EMIF CE3
16M
0300_0000 – 03FF_FFFF
Reserved
1G – 64M
0400_0000 – 3FFF_FFFF
XBus XCE0
256M
4000_0000 – 4FFF_FFFF
XBus XCE1
256M
5000_0000 – 5FFF_FFFF
XBus XCE2
256M
6000_0000 – 6FFF_FFFF
XBus XCE3
256M
7000_0000 – 7FFF_FFFF
Internal Data RAM
512K
8000_0000 – 8007_FFFF
Reserved
2G – 512K
8008_0000 – FFFF_FFFF
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
PRODUCT PREVIEW
MEMORY BLOCK DESCRIPTION
MAP 0
11
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
DMA synchronization events
The C6203B/C6203C DMA supports up to four independent programmable DMA channels, plus an auxiliary
channel used for servicing the HPI module. The four main DMA channels can be read/write synchronized based
on the events shown in Table 3. Selection of these events is done via the RSYNC and WSYNC fields in the
Primary Control registers of the specific DMA channel. For more detailed information on the DMA module,
associated channels, and event-synchronization, see the Direct Memory Access (DMA) Controller chapter of
the TMS320C6000 Peripherals Reference Guide (literature number SPRU190).
PRODUCT PREVIEW
Table 3. TMS320C6203B/03C DMA Synchronization Events
DMA EVENT
NUMBER
(BINARY)
EVENT NAME
00000
Reserved
00001
TINT0
Timer 0 interrupt
00010
TINT1
Timer 1 interrupt
00011
SD_INT
00100
EXT_INT4
External interrupt pin 4
00101
EXT_INT5
External interrupt pin 5
00110
EXT_INT6
External interrupt pin 6
00111
01000
EXT_INT7
External interrupt pin 7
DMA_INT0
DMA channel 0 interrupt
01001
01010
DMA_INT1
DMA channel 1 interrupt
DMA_INT2
DMA channel 2 interrupt
01011
DMA_INT3
DMA channel 3 interrupt
01100
XEVT0
McBSP0 transmit event
01101
REVT0
McBSP0 receive event
01110
XEVT1
McBSP1 transmit event
01111
REVT1
McBSP1 receive event
10000
DSP_INT
10001
XEVT2
McBSP2 transmit event
10010
REVT2
McBSP2 receive event
10011 – 11111
Reserved
12
EVENT DESCRIPTION
Reserved
EMIF SDRAM timer interrupt
Host processor-to-DSP interrupt
Reserved. Not used.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
interrupt sources and interrupt selector
The C62x DSP core supports 16 prioritized interrupts, which are listed in Table 4. The highest-priority interrupt
is INT_00 (dedicated to RESET) while the lowest-priority interrupt is INT_15. The first four interrupts
(INT_00–INT_03) are non-maskable and fixed. The remaining interrupts (INT_04–INT_15) are maskable and
default to the interrupt source specified in Table 4. The interrupt source for interrupts 4–15 can be programmed
by modifying the selector value (binary value) in the corresponding fields of the Interrupt Selector Control
registers: MUXH (address 0x019C0000) and MUXL (address 0x019C0004).
Table 4. C6203B/03C DSP Interrupts
INTERRUPT
SELECTOR
CONTROL
REGISTER
SELECTOR
VALUE
(BINARY)
INTERRUPT
EVENT
INT_00†
INT_01†
–
–
RESET
–
–
NMI
INT_02†
INT_03†
–
–
Reserved
Reserved. Do not use.
–
–
Reserved
Reserved. Do not use.
INT_04‡
INT_05‡
MUXL[4:0]
00100
EXT_INT4
External interrupt pin 4
MUXL[9:5]
00101
EXT_INT5
External interrupt pin 5
INT_06‡
INT_07‡
MUXL[14:10]
00110
EXT_INT6
External interrupt pin 6
MUXL[20:16]
00111
EXT_INT7
External interrupt pin 7
INT_08‡
INT_09‡
MUXL[25:21]
01000
DMA_INT0
DMA channel 0 interrupt
MUXL[30:26]
01001
DMA_INT1
DMA channel 1 interrupt
INT_10‡
INT_11‡
MUXH[4:0]
00011
SD_INT
MUXH[9:5]
01010
DMA_INT2
DMA channel 2 interrupt
INT_12‡
INT_13‡
MUXH[14:10]
01011
DMA_INT3
DMA channel 3 interrupt
MUXH[20:16]
00000
DSP_INT
INT_14‡
INT_15‡
MUXH[25:21]
00001
TINT0
Timer 0 interrupt
MUXH[30:26]
00010
TINT1
Timer 1 interrupt
–
–
01100
XINT0
McBSP0 transmit interrupt
–
–
01101
RINT0
McBSP0 receive interrupt
–
–
01110
XINT1
McBSP1 transmit interrupt
–
–
01111
RINT1
McBSP1 receive interrupt
–
–
10000
Reserved
–
–
10001
XINT2
McBSP2 transmit interrupt
–
–
10010
RINT2
McBSP2 receive interrupt
–
–
10011 – 11111
Reserved
INTERRUPT SOURCE
PRODUCT PREVIEW
CPU
INTERRUPT
NUMBER
EMIF SDRAM timer interrupt
Host-processor-to-DSP interrupt
Reserved. Not used.
Reserved. Do not use.
† Interrupts INT_00 through INT_03 are non-maskable and fixed.
‡ Interrupts INT_04 through INT_15 are programmable by modifying the binary selector values in the Interrupt Selector Control
registers fields. Table 4 shows the default interrupt sources for Interrupts INT_04 through INT_15. For more detailed
information on interrupt sources and selection, see the Interrupt Selector and External Interrupts chapter of the
TMS320C6000 Peripherals Reference Guide (literature number SPRU190).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
13
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
signal groups description
CLKIN
CLKOUT2
CLKOUT1
PRODUCT PREVIEW
CLKMODE0
CLKMODE1
CLKMODE2†
PLLV
PLLG
PLLF
Clock/PLL
Reset and
Interrupts
TMS
TDO
TDI
TCK
TRST
EMU1
EMU0
IEEE Standard
1149.1
(JTAG)
Emulation
RSV4
RSV3
RSV2
RSV1
RSV0
Reserved
DMA Status
DMAC3
DMAC2
DMAC1
DMAC0
Power-Down
Status
PD
Control/Status
† CLKMODE2 is NOT available on the GNZ package for the C6203C device.
Figure 2. CPU (DSP Core) Signals
14
POST OFFICE BOX 1443
RESET
NMI
EXT_INT7
EXT_INT6
EXT_INT5
EXT_INT4
IACK
INUM3
INUM2
INUM1
INUM0
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
signal groups description (continued)
Asynchronous
Memory
Control
32
Data
CE3
CE2
CE1
CE0
EA[21:2]
BE3
BE2
BE1
BE0
TOUT1
TINP1
Memory Map
Space Select
20
Synchronous
Memory
Control
Word Address
HOLD/
HOLDA
Byte Enables
SDA10
SDRAS/SSOE
SDCAS/SSADS
SDWE/SSWE
HOLD
HOLDA
EMIF
(External Memory Interface)
Timer 1
Timer 0
PRODUCT PREVIEW
ED[31:0]
ARE
AOE
AWE
ARDY
TOUT0
TINP0
Timers
McBSP1
McBSP0
CLKX1
FSX1
DX1
Transmit
Transmit
CLKX0
FSX0
DX0
CLKR1
FSR1
DR1
Receive
Receive
CLKR0
FSR0
DR0
CLKS1
Clock
Clock
CLKS0
McBSP2
Transmit
CLKX2
FSX2
DX2
Receive
CLKR2
FSR2
DR2
Clock
CLKS2
McBSPs
(Multichannel Buffered Serial Ports)
Figure 3. Peripheral Signals
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
15
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
signal groups description (continued)
32
XD[31:0]
XBE3/XA5
XBE2/XA4
XBE1/XA3
XBE0/XA2
XRDY
Data
Clocks
Byte-Enable
Control/
Address
Control
I/O Port
Control
XHOLD
PRODUCT PREVIEW
XHOLDA
XFCLK
XOE
XRE
XWE/XWAIT
XCE3
XCE2
XCE1
XCE0
Arbitration
Expansion Bus
Host
Interface
Control
Figure 3. Peripheral Signals (Continued)
16
XCLKIN
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
XCS
XAS
XCNTL
XW/R
XBLAST
XBOFF
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
TYPE†
C12
B10
I
Clock input
AD20
Y18
O
Clock output at full device speed
DESCRIPTION
CLOCK/PLL
CLKIN
CLKOUT1
Clock output at half (1/2) of device speed (C6203B only)
AC19
AB19
O
•
Used for synchronous memory interface
Clock mode selects
• Selects what multiply factors of the input clock frequency the CPU frequency
equals.
For more details on the GNZ,
GNZ GLS,
GLS and GNY CLKMODE pins and the PLL multiply
m ltipl
factors for the C6203B and C6203C devices, see the Clock PLL section of this data sheet.
CLKMODE0
B15
B12
I
CLKMODE1
C11
A9
I
CLKMODE2
–
A14
I
PLLV‡
PLLG‡
D13
C11
PLL analog VCC connection for the low-pass filter
D14
C12
A§
A§
PLLF‡
C13
A11
A§
PLL low-pass filter connection to external components and a bypass capacitor
TMS
AD7
Y5
I
TDO
AE6
AA4
O/Z
PRODUCT PREVIEW
CLKOUT2
Clock output at half (1/2) or at quarter (1/4) of device speed, dependent on SCRT (XD7 pin)
[C6203C only].
When SCRT (XD7 pin) = 0, then the clock output is at half of device speed
When SCRT (XD7 pin) = 1, then the clock output is at quarter of device speed
PLL analog GND connection for the low-pass filter
JTAG EMULATION
JTAG test-port mode select (features an internal pullup)
JTAG test-port data out
TDI
AF5
Y4
I
JTAG test-port data in (features an internal pullup)
TCK
AE5
AB2
I
JTAG test-port clock
TRST
AC7
AA3
I
JTAG test-port reset (features an internal pulldown)
EMU1
AF6
AA5
I/O/Z
EMU0
AC8
AB4
I/O/Z
RESET
K2
J3
I
Device reset
NMI
L2
K2
I
Nonmaskable interrupt
• Edge-driven (rising edge)
EXT_INT7
V4
U2
EXT_INT6
Y2
U3
EXT_INT5
AA1
W1
I
EXT_INT4
W4
V2
External interrupts
• Edge-driven
y independently
y selected via the External Interrupt Polarity
y Register
g
• Polarity
bits
(EXTPOL.[3:0])
(EXTPOL [3 0])
IACK
Y1
V1
O
Interrupt acknowledge for all active interrupts serviced by the CPU
INUM3
V2
R3
INUM2
U4
T1
O
Active interrupt identification number
• Valid during IACK for all active interrupts (not just external)
• Encoding order follows the interrupt-service
interru t-service fetch-packet
fetch- acket ordering
Emulation pin 1, pullup with a dedicated 20-kΩ resistor¶
Emulation pin 0, pullup with a dedicated 20-kΩ resistor¶
RESET AND INTERRUPTS
INUM1
V3
T2
INUM0
W2
T3
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
‡ PLLV, PLLG, and PLLF are not part of external voltage supply or ground. See the clock PLL section for information on how to connect these pins.
§ A = Analog Signal (PLL Filter)
¶ For emulation and normal operation, pull up EMU1 and EMU0 with a dedicated 20-kΩ resistor. For boundary scan, pull down EMU1 and EMU0
with a dedicated 20-kΩ resistor.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
17
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
TYPE†
Y2
O
DESCRIPTION
POWER-DOWN STATUS
PD
AB2
Power-down modes 2 or 3 (active if high)
PRODUCT PREVIEW
EXPANSION BUS
XCLKIN
A9
C8
I
Expansion bus synchronous host interface clock input
XFCLK
B9
A8
O
Expansion bus FIFO interface clock output
XD31
D15
C13
XD30
B16
A13
XD29
A17
C14
XD28
B17
B14
XD27
D16
B15
XD26
A18
C15
XD25
B18
A15
XD24
D17
B16
XD23
C18
C16
XD22
A20
A17
XD21
D18
B17
XD20
C19
C17
XD19
A21
B18
XD18
D19
A19
XD17
C20
C18
XD16
B21
B19
XD15
A22
C19
XD14
D20
B20
XD13
B22
A21
XD12
E25
C21
XD11
F24
D20
XD10
E26
B22
XD9
F25
D21
XD8
G24
E20
XD7
H23
E21
XD6
F26
D22
XD5
G25
F20
XD4
J23
F21
XD3
G26
E22
XD2
H25
G20
XD1
J24
G21
Ex ansion bus data
Expansion
• Used for transfer of data,, address,, and control
• Al
Also controls
l iinitialization
i i li i off DSP modes
d and
d expansion
i b
bus at reset
[Note: For more information on pin control and boot configuration fields,
fields see the Boot Modes
and Configuration cha
chapter
ter of the TMS320C6000 Peri
Peripherals
herals Reference Guide (literature
number SPRU190)]
)]
I/O/Z
XD[30:16]–
XD13
–
XD12
–
XD11
–
XD10
–
XD9
–
XD8
–
XD7
–
XD[4:0] –
XCE[3:0] memory type
olarity
XBLAST polarity
XW/R polarity
A
Asynchronous
h
or synchronous
h
h
hostt operation
ti
Arbitration mode (internal or external)
FIFO mode
Little endian/big endian
SCRT select
l t (internal
(i t
l pullup
ll [IPU] C6203C only)
l )
Boot mode
All other expansion bus data pins not listed should be pulled down.
XD0
K23
G22
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
18
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
XCE3
F2
D2
XCE2
E1
B1
TYPE†
DESCRIPTION
EXPANSION BUS (CONTINUED)
F3
D3
XCE0
E2
C2
XBE3/XA5
C7
C5
XBE2/XA4
D8
A4
Expansion bus I/O port memory space enables
• Enabled by bits 28,
28 29,
29 and 30 of the word address
• Only one asserted during any I/O port
ort data access
I/O/Z
Expansion bus multiplexed byte-enable control/address signals
• Act as byte-enable
byte enable for host-port
host port operation
• Act as address for I/O port
ort o
operation
eration
XBE1/XA3
A6
B5
XBE0/XA2
C8
C6
XOE
A7
A6
O/Z
Expansion bus I/O port output-enable
XRE
C9
C7
O/Z
Expansion bus I/O port read-enable
XWE/XWAIT
D10
B7
O/Z
Expansion bus I/O port write-enable and host-port wait signals
XCS
A10
C9
I
XAS
D9
B6
I/O/Z
XCNTL
B10
B9
I
XW/R
D11
B8
I/O/Z
Expansion bus host-port write/read-enable. XW/R polarity is selected at reset.
XRDY
A5
C4
I/O/Z
Expansion bus host-port ready (active low) and I/O port ready (active high)
XBLAST
B6
B4
I/O/Z
Expansion bus host-port burst last-polarity selected at reset
XBOFF
B11
A10
I
XHOLD
B5
A2
I/O/Z
Expansion bus hold request
XHOLDA
D7
B3
I/O/Z
Expansion bus hold acknowledge
CE3
AB25
Y21
CE2
AA24
W20
Expansion bus host-port chip-select input
Expansion bus host-port address strobe
Expansion bus host control. XCNTL selects between expansion bus address or data register.
Expansion bus back off
EMIF – CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY
CE1
AB26
AA22
CE0
AA25
W21
BE3
Y24
V20
BE2
W23
V21
BE1
AA26
W22
O/Z
Memory space enables
• Enabled by bits 24 and 25 of the word address
• Only one asserted during any external data access
O/Z
Byte-enable control
• Decoded from the two lowest bits of the internal address
y
y
y
• Byte-write
enables for most types
of memory
• C
Can b
be di
directly
tl connected
t d tto SDRAM read
d and
d write
it mask
k signal
i
l (SDQM)
BE0
Y25
U20
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
19
PRODUCT PREVIEW
XCE1
O/Z
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
EA21
J25
H20
EA20
J26
H21
EA19
L23
H22
EA18
K25
J20
EA17
L24
J21
EA16
L25
K21
EA15
M23
K20
EA14
M24
K22
EA13
M25
L21
EA12
N23
L20
EA11
P24
L22
EA10
P23
M20
EA9
R25
M21
EA8
R24
N22
EA7
R23
N20
EA6
T25
N21
EA5
T24
P21
EA4
U25
P20
EA3
T23
R22
EA2
V26
R21
TYPE†
DESCRIPTION
PRODUCT PREVIEW
EMIF – ADDRESS
O/Z
External address (word address)
EMIF – DATA
ED31
AD8
Y6
ED30
AC9
AA6
ED29
AF7
AB6
ED28
AD9
Y7
ED27
AC10
AA7
ED26
AE9
AB8
ED25
AF9
Y8
ED24
AC11
AA8
ED23
AE10
AA9
ED22
AD11
Y9
ED21
AE11
AB10
ED20
AC12
Y10
ED19
AD12
AA10
ED18
AE12
AA11
ED17
AC13
Y11
ED16
AD14
AB12
ED15
AC14
Y12
I/O/Z
External data
ED14
AE15
AA12
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
20
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
ED13
AD15
AA13
ED12
AC15
Y13
ED11
AE16
AB13
ED10
AD16
Y14
ED9
AE17
AA14
ED8
AC16
AA15
ED7
AF18
Y15
ED6
AE18
AB15
ED5
AC17
AA16
ED4
AD18
Y16
ED3
AF20
AB17
ED2
AC18
AA17
ED1
AD19
Y17
ED0
AF21
AA18
TYPE†
DESCRIPTION
EMIF – DATA (CONTINUED)
External data
PRODUCT PREVIEW
I/O/Z
EMIF – ASYNCHRONOUS MEMORY CONTROL
ARE
V24
T21
O/Z
Asynchronous memory read-enable
AOE
V25
R20
O/Z
Asynchronous memory output-enable
AWE
U23
T22
O/Z
Asynchronous memory write-enable
W25
T20
I
Asynchronous memory ready input
ARDY
EMIF – SYNCHRONOUS DRAM (SDRAM)/SYNCHRONOUS BURST SRAM (SBSRAM) CONTROL
SDA10
AE21
AA19
O/Z
SDRAM address 10 (separate for deactivate command)
SDCAS/SSADS
AE22
AB21
O/Z
SDRAM column-address strobe/SBSRAM address strobe
SDRAS/SSOE
AF22
Y19
O/Z
SDRAM row-address strobe/SBSRAM output-enable
SDWE/SSWE
AC20
AA20
O/Z
SDRAM write-enable/SBSRAM write-enable
HOLD
Y26
V22
I
Hold request from the host
HOLDA
V23
U21
O
Hold-request-acknowledge to the host
EMIF – BUS ARBITRATION
TIMER 0
TOUT0
F1
D1
O
Timer 0 or general-purpose output
TINP0
H4
E2
I
Timer 0 or general-purpose input
TIMER 1
TOUT1
J4
F2
O
Timer 1 or general-purpose output
TINP1
G2
F3
I
Timer 1 or general-purpose input
DMAC3
Y3
V3
DMAC2
AA2
W2
DMAC1
AB1
AA1
DMA ACTION COMPLETE STATUS
O
DMA action complete
DMAC0
AA3
W3
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
21
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
TYPE†
DESCRIPTION
GNZ
GLS/
GNY
CLKS0
M4
K3
I
CLKR0
M2
L2
I/O/Z
Receive clock
CLKX0
M3
K1
I/O/Z
Transmit clock
DR0
R2
M2
I
Receive data
DX0
P4
M3
O/Z
Transmit data
FSR0
N3
M1
I/O/Z
Receive frame sync
FSX0
N4
L3
I/O/Z
Transmit frame sync
CLKS1
G1
E1
I
CLKR1
J3
G2
I/O/Z
Receive clock
CLKX1
H2
G3
I/O/Z
Transmit clock
DR1
L4
H1
I
Receive data
DX1
J1
H2
O/Z
Transmit data
FSR1
J2
H3
I/O/Z
Receive frame sync
FSX1
K4
G1
I/O/Z
Transmit frame sync
MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP0)
External clock source (as opposed to internal)
PRODUCT PREVIEW
MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1)
External clock source (as opposed to internal)
MULTICHANNEL BUFFERED SERIAL PORT 2 (McBSP2)
CLKS2
R3
N1
I
External clock source (as opposed to internal)
CLKR2
T2
N2
I/O/Z
Receive clock
CLKX2
R4
N3
I/O/Z
Transmit clock
DR2
V1
R2
I
Receive data
DX2
T4
R1
O/Z
Transmit data
FSR2
U2
P3
I/O/Z
Receive frame sync
FSX2
T3
P2
I/O/Z
Transmit frame sync
RSV0
L3
J2
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RESERVED FOR TEST
RSV1
G3
E3
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV2
A12
B11
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV3
C15
B13
O
Reserved (leave unconnected, do not connect to power or ground)
RSV4
D12
C10
O
Reserved (leave unconnected, do not connect to power or ground)
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
22
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
A11
A3
A16
A7
B7
A16
B8
A20
B19
D4
B20
D6
C6
D7
TYPE†
DESCRIPTION
DVDD
C10
D9
C14
D10
C17
D13
C21
D14
G4
D16
G23
D17
H3
D19
H24
F1
K3
F4
K24
F19
L1
F22
L26
G4
N24
G19
P3
J4
T1
J19
T26
K4
U3
K19
U24
L1
W3
M22
W24
N4
Y4
N19
Y23
P4
AD6
P19
AD10
T4
AD13
T19
AD17
U1
AD21
U4
AE7
U19
AE8
U22
AE19
W4
AE20
W6
S
PRODUCT PREVIEW
SUPPLY VOLTAGE PINS
3.3-V
3.3
V su
supply
ly voltage (I/O)
AF11
W7
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
23
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
AF16
W9
–
W10
–
W13
–
W14
–
W16
–
W17
–
W19
–
AB5
TYPE†
DESCRIPTION
SUPPLY VOLTAGE PINS (CONTINUED)
PRODUCT PREVIEW
DVDD
CVDD
–
AB9
–
AB14
–
AB18
A1
E7
A2
E8
A3
E10
A24
E11
A25
E12
A26
E13
B1
E15
B2
E16
B3
F7
B24
F8
B25
F9
B26
F11
C1
F12
C2
F14
C3
F15
C4
F16
C23
G5
C24
G6
C25
G17
C26
G18
D3
H5
D4
H6
D5
H17
D22
H18
D23
J6
D24
J17
E4
K5
E23
K18
S
3.3-V
supply
3.3
V su
ly voltage (I/O)
S
1.2-V su
supply
ly voltage (core) (C6203C only)
1.5-V
supply
1.5
V su
ly voltage (core) (C6203B only)
1.7-V supply voltage (core) (C6203BGLS 1.7-V parts only)
AB4
L5
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
24
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
AB23
L6
AC3
L17
AC4
L18
AC5
M5
AC22
M6
AC23
M17
AC24
M18
TYPE†
DESCRIPTION
CVDD
AD1
N5
AD2
N18
AD3
P6
AD4
P17
AD23
R5
AD24
R6
AD25
R17
AD26
R18
AE1
T5
AE2
T6
AE3
T17
AE24
T18
AE25
U7
AE26
U8
AF1
U9
AF2
U11
AF3
U12
AF24
U14
AF25
U15
AF26
U16
–
V7
–
V8
–
V10
–
V11
–
V12
–
V13
–
V15
–
V16
A4
A1
A8
A5
A13
A12
S
PRODUCT PREVIEW
SUPPLY VOLTAGE PINS (CONTINUED)
1.2-V su
supply
ly voltage (core) (C6203C only)
1.5-V
1.5
V su
supply
ly voltage (core) (C6203B only)
1.7-V supply voltage (core) (C6203BGLS 1.7-V parts only)
GROUND PINS
VSS
GND
Ground pins
A14
A18
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
25
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
A15
A22
A19
B2
A23
B21
B4
C1
B12
C3
B13
C20
B14
C22
B23
D5
TYPE†
DESCRIPTION
PRODUCT PREVIEW
GROUND PINS (CONTINUED)
VSS
C5
D8
C16
D11
C22
D12
D1
D15
D2
D18
D6
E4
D21
E5
D25
E6
D26
E9
E3
E14
E24
E17
F4
E18
F23
E19
H1
F5
H26
F6
K1
F10
K26
F13
M1
F17
M26
F18
N1
H4
N2
H19
N25
J1
N26
J5
P1
J18
P2
J22
P25
K6
P26
K17
GND
Ground pins
R1
L4
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
26
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
R26
L19
U1
M4
U26
M19
TYPE†
DESCRIPTION
VSS
W1
N6
W26
N17
AA4
P1
AA23
P5
AB3
P18
AB24
P22
AC1
R4
AC2
R19
AC6
U5
AC21
U6
AC25
U10
AC26
U13
AD5
U17
AD22
U18
AE4
V4
AE13
V5
AE14
V6
AE23
V9
AF4
V14
AF8
V17
AF10
V18
AF12
V19
AF13
W5
AF14
W8
AF15
W11
AF17
W12
AF19
W15
AF23
W18
–
Y1
–
Y3
–
Y20
–
Y22
–
AA2
–
AA21
GND
PRODUCT PREVIEW
GROUND PINS (CONTINUED)
Ground pins
ins
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
27
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
Signal Descriptions (Continued)
PIN NO.
SIGNAL
NAME
GNZ
GLS/
GNY
–
AB1
–
AB3
TYPE†
DESCRIPTION
GROUND PINS (CONTINUED)
VSS
–
AB7
–
AB11
–
AB16
–
AB20
GND
Ground pins
ins
–
AB22
† I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
development support
PRODUCT PREVIEW
TI offers an extensive line of development tools for the TMS320C6000 DSP platform, including tools to
evaluate the performance of the processors, generate code, develop algorithm implementations, and fully
integrate and debug software and hardware modules.
The following products support development of C6000 DSP-based applications:
Software Development Tools:
Code Composer Studio Integrated Development Environment (IDE) including Editor
C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP/BIOS), which provides the basic run-time target software
needed to support any DSP application.
Hardware Development Tools:
Extended Development System (XDS) Emulator (supports C6000 DSP multiprocessor system debug)
EVM (Evaluation Module)
The TMS320 DSP Development Support Reference Guide (SPRU011) contains information about
development-support products for all TMS320 DSP family member devices, including documentation. See
this document for further information on TMS320 DSP documentation or any TMS320 DSP support products
from Texas Instruments. An additional document, the TMS320 Third-Party Support Reference Guide
(SPRU052), contains information about TMS320 DSP-related products from other companies in the industry.
To receive TMS320 DSP literature, contact the Literature Response Center at 800/477-8924.
For a complete listing of development-support tools for the TMS320C6000 DSP platform, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL) and select
“Find Development Tools”. For device-specific tools, under “Semiconductor Products” select “Digital Signal
Processors”, choose a product family, and select the particular DSP device. For information on pricing and
availability, contact the nearest TI field sales office or authorized distributor.
Code Composer Studio, DSP/BIOS, XDS, and TMS320 are trademarks of Texas Instruments.
28
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
device and development-support tool nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
TMS320 DSP devices and support tools. Each TMS320 DSP commercial family member has one of three
prefixes: TMX, TMP, or TMS. Texas Instruments recommends two of three possible prefix designators for
support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from
engineering prototypes (TMX / TMDX) through fully qualified production devices/tools (TMS / TMDS).
Device development evolutionary flow:
TMX
Experimental device that is not necessarily representative of the final device’s electrical
specifications
TMP
Final silicon die that conforms to the device’s electrical specifications but has not completed
quality and reliability verification
TMS
Fully qualified production device
TMDX
Development-support product that has not yet completed Texas Instruments internal qualification
testing.
TMDS
Fully qualified development-support product
TMX and TMP devices and TMDX development-support tools are shipped against the following disclaimer:
“Developmental product is intended for internal evaluation purposes.”
TMS devices and TMDS development-support tools have been characterized fully, and the quality and reliability
of the device have been demonstrated fully. TI’s standard warranty applies.
Predictions show that prototype devices ( TMX or TMP) have a greater failure rate than the standard production
devices. Texas Instruments recommends that these devices not be used in any production system because their
expected end-use failure rate still is undefined. Only qualified production devices are to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type
(for example, GLS), the temperature range (for example, blank is the default commercial temperature range),
and the device speed range in megahertz (for example, -300 is 300 MHz).
Figure 4 provides a legend for reading the complete device name for any member of the TMS320C6000 DSP
platform. For the C6203B/03C device orderable part numbers (P/Ns), see the Texas Instruments web site on
the Worldwide web at http://www.ti.com URL, or contact the nearest TI field sales office, or authorized distributor.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
29
PRODUCT PREVIEW
Support tool development evolutionary flow:
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
device and development-support tool nomenclature (continued)
TMS 320
C 6203C GNZ
( )
300
PREFIX
TMX = Experimental device
TMP = Prototype device
TMS = Qualified device
SMJ = MIL-PRF-38535, QML
SM = High Rel (non-38535)
DEVICE SPEED RANGE
100 MHz
120 MHz
150 MHz
167 MHz
DEVICE FAMILY
320 = TMS320t DSP family
PRODUCT PREVIEW
TEMPERATURE RANGE (DEFAULT: 0°C TO 90°C)
Blank = 0°C to 90°C, commercial temperature
A
= –40°C to 105°C, extended temperature
PACKAGE TYPE†
GFN = 256-pin plastic BGA
GGP = 352-pin plastic BGA
GJC = 352-pin plastic BGA
GJL = 352-pin plastic BGA
GLS = 384-pin plastic BGA
GLW = 340-pin plastic BGA
GNY = 384-pin plastic BGA
GNZ = 352-pin plastic BGA
GHK = 288-pin plastic MicroStar BGAt
TECHNOLOGY
C = CMOS
DEVICE
C6000 DSP:
6201
6202
6202B
6203B
6203C
† BGA =
200 MHz
233 MHz
250 MHz
300 MHz
6204
6205
6211
6211B
6414
6415
6416
6701
Ball Grid Array
Figure 4. TMS320C6000 DSP Platform Device Nomenclature
(Including TMS320C6203B and TMS320C6203C)
MicroStar BGA is a trademark of Texas Instruments.
30
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
6711
6711B
6712
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
documentation support
Extensive documentation supports all TMS320 DSP family devices from product announcement through
applications development. The types of documentation available include: data sheets, such as this document,
with design specifications; complete user’s reference guides for all devices and tools; technical briefs;
development-support tools; on-line help; and hardware and software applications. The following is a brief,
descriptive list of support documentation specific to the C6000 DSP devices:
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189) describes the
C6000 CPU (DSP core) architecture, instruction set, pipeline, and associated interrupts.
The TMS320C6000 Peripherals Reference Guide (literature number SPRU190) describes the functionality of
the peripherals available on the C6000 DSP platform of devices, such as the 64-/32-/16-bit external memory
interfaces (EMIFs), 32-/16-bit host-port interfaces (HPIs), multichannel buffered serial ports (McBSPs), direct
memory access (DMA), enhanced direct-memory-access (EDMA) controller, expansion bus (XBus), peripheral
component interconnect (PCI), clocking and phase-locked loop (PLL); and power-down modes. This guide also
includes information on internal data and program memories.
The How to Begin Development and Migrate Across the TMS320C6202/6202B/6203B/6204 DSPs application
report (literature number SPRA603) describes the migration concerns and identifies the similarities and
differences between the C6202, C6202B, C6203B, C6203C, and C6204 C6000 DSP devices.
The tools support documentation is electronically available within the Code Composer Studio IDE. For a
complete listing of the latest C6000 DSP documentation, visit the Texas Instruments web site on the
Worldwide Web at http://www.ti.com uniform resource locator (URL).
TMS320C67x is a trademark of Texas Instruments.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
31
PRODUCT PREVIEW
The TMS320C6000 Technical Brief (literature number SPRU197) gives an introduction to the
TMS320C62x/TMS320C67x devices, associated development tools, and third-party support.
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
clock PLL
Most of the internal C6203B/03C clocks are generated from a single source through the CLKIN pin. This source
clock either drives the PLL, which multiplies the source clock in frequency to generate the internal CPU clock,
or bypasses the PLL to become the internal CPU clock.
To use the PLL to generate the CPU clock, the external PLL filter circuit must be properly designed. Figure 5,
and Table 6 through Table 8 show the external PLL circuitry for either x1 (PLL bypass) or x4 PLL multiply modes.
Figure 6 shows the external PLL circuitry for a system with ONLY x1 (PLL bypass) mode.
To minimize the clock jitter, a single clean power supply should power both the C6203B/03C device and the
external clock oscillator circuit. Noise coupling into PLLF directly impacts PLL clock jitter. The minimum CLKIN
rise and fall times should also be observed. For the input clock timing requirements, see the input and output
clocks electricals section. Table 5 lists some examples of compatible CLKIN external clock sources:
Table 5. Compatible CLKIN External Clock Sources
COMPATIBLE PARTS FOR
EXTERNAL CLOCK SOURCES (CLKIN)
PART NUMBER
MANUFACTURER
JITO-2
Fox Electronix
STA series, ST4100 series
SaRonix Corporation
SG-636
Epson America
342
Corning Frequency Control
MK1711-S, ICS525-02
Integrated Circuit Systems
PRODUCT PREVIEW
Oscillators
PLL
3.3V
PLLV
EMI Filter
C3
10 mF
C4
0.1 mF
CLKMODE0
CLKMODE1
CLKMODE2†
CLKIN
Internal to
C6203B/C6203C
PLL
PLLMULT
PLLCLK
CLKIN
1
LOOP FILTER
C2
C1
CPU
CLOCK
PLLG
(For the PLL Options
and CLKMODE pins setup,
see Table 6 through Table 9)
PLLF
0
R1
† The CLKMODE2 pin is not available for the C6203C GNZ package.
NOTES: A. Keep the lead length and the number of vias between pin PLLF, pin PLLG, R1, C1, and C2 to a minimum. In addition, place all PLL
components (R1, C1, C2, C3, C4, and EMI Filter) as close to the C6000 DSP device as possible. Best performance is achieved
with the PLL components on a single side of the board without jumpers, switches, or components other than the ones shown.
B. For reduced PLL jitter, maximize the spacing between switching signals and the PLL external components (R1, C1, C2, C3, C4,
and the EMI Filter).
C. The 3.3-V supply for the EMI filter must be from the same 3.3-V power plane supplying the I/O voltage, DVDD.
D. EMI filter manufacturer: TDK part number ACF451832-333, 223, 153, 103. Panasonic part number EXCCET103U.
Figure 5. External PLL Circuitry for Either PLL Multiply Modes or x1 (Bypass) Mode
32
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
clock PLL (continued)
3.3V
PLLV
CLKMODE0
CLKMODE1
CLKMODE2†
Internal to
C6203B/C6203C
PLL
PLLMULT
PLLCLK
CLKIN
CLKIN
1
LOOP FILTER
CPU
CLOCK
PLLG
PLLF
0
† The CLKMODE2 pin is not available for the C6203C GNZ package.
NOTES: A. For a system with ONLY PLL x1 (bypass) mode, short the PLLF to PLLG.
B. The 3.3-V supply for PLLV must be from the same 3.3-V power plane supplying the I/O voltage, DVDD.
Table 6. TMS320C6203B GLS and C6203B/C6203C GNY Packages PLL Multiply and Bypass (x1) Options†
GLS PACKAGE – 18 x 18 mm BGA [C6203B only] and
GNY PACKAGE – 18 x 18 mm BGA [C6203B and C6203C]
BIT
(PIN NO.)
Value
DEVICES AND PLL CLOCK OPTIONS
CLKMODE2
(A14)
CLKMODE1
(A9)
CLKMODE0
(B12)
C6203B (GLS, GNY)
C6203C (GNY)
0
0
0
Bypass (x1)
Bypass (x1)
0
0
1
x4
x4
0
1
0
x8
x8
0
1
1
x10
x12
1
0
0
x6
x6
1
0
1
x9
x8
1
1
0
x7
x6
1
1
1
x11
x8
† f(CPU Clock) = f(CLKIN) x (PLL mode)
Table 7. TMS320C6203C GNZ Package PLL Multiply and Bypass (x1) Options†
GNZ PACKAGE 27 x 27 mm BGA [C6203C only]
BIT
(PIN NO.)
Value
CLKMODE2
(N/A)‡
N/A
CLKMODE1
(C11)
CLKMODE0
(B15)
DEVICES AND PLL CLOCK OPTIONS
0
0
Bypass (x1)
0
1
x4
1
0
x8
1
1
x12
† f(CPU Clock) = f(CLKIN) x (PLL mode)
‡ The CLKMODE2 pin is not available (N/A) for the C6203C GNZ package.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
33
PRODUCT PREVIEW
Figure 6. External PLL Circuitry for x1 (Bypass) PLL Mode Only
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
clock PLL (continued)
Table 8. TMS320C6203B PLL Component Selection Table†
CLKMODE‡
CLKIN
RANGE
(MHz)
x4
32.5–75
x6
21.7–50
x7
18.6–42.9
x8
16.3–37.5
x9
14.4–33.3
x10
13–30
x11
11.8–27.3
CPU CLOCK
FREQUENCY
RANGE (MHz)
CLKOUT2
RANGE
(MHz)
R1 [±1%]
(Revision No.)
C1 [±10%]
(Revision No.)
C2 [±10%]
(Revision No.)
TYPICAL
LOCK TIME
(µs)
130–300
130
300
65–150
65
150
60 4 Ω (1.x)
60.4
(1 )
45.3
(2.x,
3.x)
45
3 Ω (2
x 3
x)
27 nF
F (1.x)
(1 )
47 nF (2.x,
(2 x 3.x)
3 x)
560 pF
F (1
(1.x))
10 pF (2.x,
(2 x 3.x)
3 x)
75
† Under some operating conditions, the maximum PLL lock time may vary by as much as 150% from the specified typical value. For example, if
the typical lock time is specified as 100 µs, the maximum value may be as long as 250 µs.
‡ CLKMODE x1, x4, x6, x7, x8, x9, x10, and x11 apply to the GLS/GNY devices [C6203B only].
PRODUCT PREVIEW
Table 9. TMS320C6203C PLL Component Selection Table†
CLKMODE‡
CLKIN
RANGE
(MHz)
x4
32–75
x6
32–66.67
x8
32–50
CPU CLOCK
FREQUENCY
RANGE (MHz)
CLKOUT2
RANGE
(MHz)
R1 [±1%]§¶
C1 [±10%]§¶
C2 [±10%]§¶
TYPICAL
LOCK TIME
(µs)
128 400
128–400
64 200
64–200
45 3 60 4 Ω
45.3–60.4
27 47 nF
27–47
10 560 pF
10–560
75
x12
32–33.33
† Under some operating conditions, the maximum PLL lock time may vary by as much as 150% from the specified typical value. For example, if
the typical lock time is specified as 100 µs, the maximum value may be as long as 250 µs.
‡ CLKMODE x1, x4, x6, x8, and x12 apply to the GNY device. The GNZ device is restricted to x1, x4, x8, and x12 multiply factors.
§ The PLL component selection for the C6203C device is specified as a range because the C6203C device can use the same PLL components
as the C6203B, C6202/02B, or C6204 devices.
¶ For the C6203C device, the R1, C1, and C2 components are not required; however, for the benefit of being able to migrate between the C6203B,
C6202/02B, and C6204 devices, it is recommended that these components be installed.
34
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
power-supply sequencing
TI DSPs do not require specific power sequencing between the core supply and the I/O supply. However,
systems should be designed to ensure that neither supply is powered up for extended periods of time if the other
supply is below the proper operating voltage.
system-level design considerations
System-level design considerations, such as bus contention, may require supply sequencing to be
implemented. In this case, the core supply should be powered up at the same time as, or prior to (and powered
down after), the I/O buffers. This is to ensure that the I/O buffers receive valid inputs from the core before the
output buffers are powered up, thus, preventing bus contention with other chips on the board.
For systems using the C6000 DSP platform of devices, the core supply may be required to provide in excess
of 2 A per DSP until the I/O supply is powered up. This extra current condition is a result of uninitialized logic
within the DSP(s) and is corrected once the CPU sees an internal clock pulse. With the PLL enabled, as the
I/O supply is powered on, a clock pulse is produced stopping the extra current draw from the supply. With the
PLL disabled, as many as five external clock cycle pulses may be required to stop this extra current draw. A
normal current state returns once the I/O power supply is turned on and the CPU sees a clock pulse. Decreasing
the amount of time between the core supply power up and the I/O supply power up can minimize the effects
of this current draw.
A dual-power supply with simultaneous sequencing, such as available with TPS563xx controllers or PT69xx
plug-in power modules, can be used to eliminate the delay between core and I/O power up [see the Using the
TPS56300 to Power DSPs application report (literature number SLVA088)]. A Schottky diode can also be used
to tie the core rail to the I/O rail, effectively pulling up the I/O power supply to a level that can help initialize the
logic within the DSP.
Core and I/O supply voltage regulators should be located close to the DSP (or DSP array) to minimize
inductance and resistance in the power delivery path. Additionally, when designing for high-performance
applications utilizing the C6000 platform of DSPs, the PC board should include separate power planes for
core, I/O, and ground, all bypassed with high-quality low-ESL/ESR capacitors.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
35
PRODUCT PREVIEW
power-supply design considerations
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
absolute maximum ratings over operating case temperature ranges (unless otherwise noted)†
Supply voltage range, CVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 1.8 V
Supply voltage range, DVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4 V
Input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4 V
Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4 V
Operating case temperature ranges, TC:(default) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0_C to 90_C
(A version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40_C to105_C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65_C to 150_C
Temperature cycle range, (1000-cycle performance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40_C to 125_C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to VSS.
recommended operating conditions
PRODUCT PREVIEW
Supply voltage, Core
C6203C only
MIN
NOM
MAX
UNIT
1.14
1.2
1.26
V
1.43
1.5
1.57
V
1.65
1.7
1.75
V
3.14
3.3
3.46
V
0
0
V
CVDD
Supply voltage, Core
Supply voltage, Core‡
DVDD
Supply voltage, I/O
VSS
VIH
Supply ground
0
High-level input voltage
2
VIL
IOH
Low-level input voltage
0.8
V
High-level output current
–8
mA
IOL
Low-level output current
8
mA
90
_C
C6203B only
Default
TC
V
0
Operating case temperature
A version
–40
105
_C
‡ Supply voltage, Core for the C6203B 1.7 V devices which are identified in the orderable part number with a “17” following the device number
and the package type identifiers.
electrical characteristics over recommended ranges of supply voltage and operating case
temperature (unless otherwise noted)
PARAMETER
VOH
VOL
II
IOZ
TEST CONDITIONS
High-level output voltage
DVDD = MIN,
Low-level output voltage
Input current§
DVDD = MIN,
IDD2V
Supply current
current, CPU + CPU memory access¶
IDD2V
Supply current,
current peripherals¶
current I/O pins¶
Supply current,
Ci
Input capacitance
TYP
MAX
2.4
UNIT
V
VI = VSS to DVDD
VO = DVDD or 0 V
Off-state output current
IDD3V
IOH = MAX
IOL = MAX
MIN
0.6
V
±10
uA
±10
uA
C6203B, CVDD = NOM, CPU clock = 200 MHz
340
mA
C6203C, CVDD = NOM, CPU clock = 200 MHz
TBD
mA
C6203B, CVDD = NOM, CPU clock = 200 MHz
235
mA
C6203C, CVDD = NOM, CPU clock = 200 MHz
TBD
mA
C6203B, CVDD = NOM, CPU clock = 200 MHz
45
mA
C6203C, CVDD = NOM, CPU clock = 200 MHz
TBD
mA
10
pF
Co
Output capacitance
10
pF
§ TMS and TDI are not included due to internal pullups. TRST is not included due to internal pulldown.
¶ Measured with average activity (50% high / 50% low power). For more details on CPU, peripheral, and I/O activity, see the TMS320C6000 Power
Consumption Summary application report (literature number SPRA486).
36
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
PARAMETER MEASUREMENT INFORMATION
IOL
Tester Pin
Electronics
50 Ω
Vcomm
Output
Under
Test
CT
IOH
IOL
IOH
Vcomm
CT
=
=
=
=
2 mA
2 mA
0.8 V
15-pF typical load-circuit capacitance
Figure 7. Test Load Circuit for AC Timing Measurements
signal transition levels
All input and output timing parameters are referenced to 1.5 V for both “0” and “1” logic levels.
Vref = 1.5 V
Figure 8. Input and Output Voltage Reference Levels for ac Timing Measurements
All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, and
VOL MAX and VOH MIN for output clocks.
Vref = VIH MIN (or VOH MIN)
Vref = VIL MAX (or VOL MAX)
Figure 9. Rise and Fall Transition Time Voltage Reference Levels
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
37
PRODUCT PREVIEW
Where:
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
PARAMETER MEASUREMENT INFORMATION (CONTINUED)
timing parameters and board routing analysis
The timing parameter values specified in this data sheet do not include delays by board routings. As a good
board design practice, such delays must always be taken into account. Timing values may be adjusted by
increasing/decreasing such delays. TI recommends utilizing the available I/O buffer information specification
(IBIS) models to analyze the timing characteristics correctly. If needed, external logic hardware such as buffers
may be used to compensate any timing differences.
For inputs, timing is most impacted by the round-trip propagation delay from the DSP to the external device and
from the external device to the DSP. This round-trip delay tends to negatively impact the input setup time margin,
but also tends to improve the input hold time margins (see Table 10 and Figure 10).
Figure 10 represents a general transfer between the DSP and an external device. The figure also represents
board route delays and how they are perceived by the DSP and the external device.
Table 10. IBIS Timing Parameters Example (see Figure 10)
PRODUCT PREVIEW
NO.
DESCRIPTION
1
Clock route delay
2
Minimum DSP hold time
3
Minimum DSP setup time
4
External device hold time requirement
5
External device setup time requirement
6
Control signal route delay
7
External device hold time
8
External device access time
9
DSP hold time requirement
10
DSP setup time requirement
11
Data route delay
CLKOUT2
(Output from DSP)
1
CLKOUT2
(Input to External Device)
Control Signals†
(Output from DSP)
2
3
4
5
Control Signals
(Input to External Device)
6
7
Data Signals‡
(Output from External Device)
8
10
9
11
Data Signals‡
(Input to DSP)
† Control signals include data for Writes.
‡ Data signals are generated during Reads from an external device.
Figure 10. IBIS Input/Output Timings
38
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
INPUT AND OUTPUT CLOCKS
timing requirements for CLKIN (PLL used)†‡§ (see Figure 11)
C6203B-250
NO
NO.
1
2
3
4
MIN
C6203B-300
MAX
MIN
C6203C-300
MAX
MIN
MAX
UNIT
tc(CLKIN)
tw(CLKINH)
Cycle time, CLKIN
4*M
3.33 * M
3.33 * M
ns
Pulse duration, CLKIN high
0.4C
0.4C
0.4C
ns
tw(CLKINL)
tt(CLKIN)
Pulse duration, CLKIN low
0.4C
0.4C
Transition time, CLKIN
0.4C
5
ns
5
5
ns
† The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
‡ M = the PLL multiplier factor (x4, x6, x7, x8, x9, x10, or x11) for C6203B GLS and GNY only.
M = the PLL multiplier factor (x4, x8, or x12) for C6203C GNZ only. M = the PLL multiplier factor (x4, x6, x8, or x12) for C6203C GNY only.
For more details on both devices, see the Clock PLL section of this data sheet.
§ C = CLKIN cycle time in ns. For example, when CLKIN frequency is 50 MHz, use C = 20 ns.
timing requirements for CLKIN [PLL bypassed (x1)]†¶ (see Figure 11)
1
2
3
MIN
C6203B-300
MAX
MIN
C6203C-300
MAX
MIN
MAX
UNIT
tc(CLKIN)
tw(CLKINH)
Cycle time, CLKIN
4
3.33
TBD
ns
Pulse duration, CLKIN high
0.45C
0.45C
0.45C
ns
tw(CLKINL)
tt(CLKIN)
Pulse duration, CLKIN low
0.45C
0.45C
0.45C
ns
4
Transition time, CLKIN
0.6
0.6
0.6
ns
† The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
¶ C = CLKIN cycle time in ns. For example, when CLKIN frequency is 50 MHz, use C = 20 ns. The maximum CLKIN cycle time in PLL bypass mode
(x1) is 200 MHz.
1
4
2
CLKIN
3
4
Figure 11. CLKIN Timings
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
39
PRODUCT PREVIEW
C6203B-250
NO
NO.
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
INPUT AND OUTPUT CLOCKS (CONTINUED)
timing requirements for XCLKIN† (see Figure 12)
C6203B-250
C6203B-300
C6203C-300
NO.
MIN
1
tc(XCLKIN)
tw(XCLKINH)
2
Cycle time, XCLKIN
Pulse duration, XCLKIN high
3
tw(XCLKINL) Pulse duration, XCLKIN low
† P = 1/CPU clock frequency in nanoseconds (ns).
UNIT
MAX
4P
ns
1.8P
ns
1.8P
ns
1
2
XCLKIN
PRODUCT PREVIEW
3
Figure 12. XCLKIN Timings
switching characteristics over recommended operating conditions for CLKOUT2ठ(see Figure 13)
NO.
1
2
C6203B-250
C6203B-300
C6203C-300
PARAMETER
tc(CKO2)
tw(CKO2H)
Cycle time, CLKOUT2
Pulse duration, CLKOUT2 high
3
tw(CKO2L)
Pulse duration, CLKOUT2 low
‡ For the C6203B device only, P = 1/CPU clock frequency in ns.
For the C6203C device only:
If the SCRT (XD7 pin) is pulled down (0) then, P = 1/CPU clock frequency in ns.
If the SCRT (XD7 pin) is pulled up (1) then, P = 2(1/CPU clock frequency in ns).
§ The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
1
2
CLKOUT2
3
Figure 13. CLKOUT2 Timings
40
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
UNIT
MIN
MAX
2P – 0.7
2P + 0.7
ns
P – 0.7
P + 0.7
ns
P – 0.7
P + 0.7
ns
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
INPUT AND OUTPUT CLOCKS (CONTINUED)
switching characteristics over recommended operating conditions for XFCLK†‡ (see Figure 14)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
1
2
tc(XFCK)
tw(XFCKH)
Cycle time, XFCLK
Pulse duration, XFCLK high
3
tw(XFCKL)
Pulse duration, XFCLK low
† P = 1/CPU clock frequency in ns.
‡ D = 8, 6, 4, or 2; FIFO clock divide ratio, user-programmable
UNIT
MAX
D * P – 0.7
D * P + 0.7
ns
(D/2) * P – 0.7
(D/2) * P + 0.7
ns
(D/2) * P – 0.7
(D/2) * P + 0.7
ns
1
2
XFCLK
PRODUCT PREVIEW
3
Figure 14. XFCLK Timings
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
41
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
ASYNCHRONOUS MEMORY TIMING
timing requirements for asynchronous memory cycles†‡§¶ (see Figure 15 – Figure 18)
C6203B-250
C6203B-300
NO.
PRODUCT PREVIEW
MIN
3
tsu(EDV-AREH)
Setup time, EDx valid before
ARE high
4
th(AREH-EDV)
Hold time, EDx valid after
ARE high
6
tsu(ARDYH-AREL)
Setup time, ARDY high before
ARE low
7
th(AREL-ARDYH)
Hold time, ARDY high after
ARE low
9
tsu(ARDYL-AREL)
Setup time, ARDY low before
ARE low
10
th(AREL-ARDYL)
Hold time, ARDY low after
ARE low
11
tw(ARDYH)
Pulse width, ARDY high
15
tsu(ARDYH-AWEL)
Setup time, ARDY high before
AWE low
16
th(AWEL-ARDYH)
Hold time, ARDY high after
AWE low
18
tsu(ARDYL-AWEL)
Setup time, ARDY low before
AWE low
19
th(AWEL-ARDYL)
Hold time, ARDY low after
AWE low
C6203C-300
MAX
MIN
UNIT
MAX
1
3
ns
4.9
1
ns
–[(RST – 3) * P – 6]
–[(RST – 3) * P – 6]
ns
(RST – 3) * P + 2
(RST – 3) * P + 2
ns
–[(RST – 3) * P – 6]
–[(RST – 3) * P – 6]
ns
(RST – 3) * P + 2
(RST – 3) * P + 2
ns
2P
2P
ns
–[(WST – 3) * P – 6]
–[(WST – 3) * P – 6]
ns
(WST – 3) * P + 2
(WST – 3) * P + 2
ns
–[(WST – 3) * P – 6]
–[(WST – 3) * P – 6]
ns
(WST – 3) * P + 2
(WST – 3) * P + 2
ns
† To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. If ARDY does meet setup or hold
time, it may be recognized in the current cycle or the next cycle. Thus, ARDY can be an asynchronous input.
‡ RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the EMIF CE space control registers.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
¶ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use ARDY input to extend strobe width.
42
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
switching characteristics over recommended operating conditions for asynchronous memory
cycles†‡§¶ (see Figure 15 – Figure 18)
C6203B-250
C6203B-300
PARAMETER
MIN
TYP
C6203C-300
MAX
MIN
TYP
UNIT
MAX
1
tosu(SELV-AREL)
Output setup time, select
signals valid to ARE low
RS * P – 2
RS * P – 1
ns
2
toh(AREH-SELIV)
Output hold time, ARE high to
select signals invalid
RH * P – 2
RH * P – 1
ns
5
tw(AREL)
Pulse width, ARE low
8
td(ARDYH-AREH)
Delay time, ARDY high to
ARE high
3P
12
tosu(SELV-AWEL)
Output setup time, select
signals valid to AWE low
WS * P – 3
WS * P – 1
ns
13
toh(AWEH-SELIV)
Output hold time, AWE high
to select signals invalid
WH * P – 2
WH * P – 1
ns
14
tw(AWEL)
Pulse width, AWE low
17
td(ARDYH-AWEH)
Delay time, ARDY high to
AWE high
RST * P
RST * P
4P + 5
3P
WST * P
3P
ns
4P + 3
WST * P
4P + 5
3P
ns
ns
4P + 3
ns
† RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the EMIF CE space control registers.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
§ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use ARDY input to extend strobe width.
¶ Select signals include: CEx, BE[3:0], EA[21:2], AOE; and for writes, include ED[31:0], with the exception that CEx can stay active for an additional
7P ns following the end of the cycle.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
43
PRODUCT PREVIEW
NO.
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2
Strobe = 3
Hold = 2
CLKOUT1
1
2
1
2
1
2
CEx†
BE[3:0]
EA[21:2]
3
4
ED[31:0]
1
2
PRODUCT PREVIEW
AOE
6
7
ARE
5
AWE
ARDY
† CEx stays active for seven minus the value of Read Hold cycles after the last access (DMA transfer or CPU access). For example, if read
HOLD = 1, then CEx stays active for six more cycles. This does not affect performance, it merely reflects the EMIF’s overhead.
Figure 15. Asynchronous Memory Read Timing (ARDY Not Used)
Setup = 2
Strobe = 3
Not Ready
Hold = 2
CLKOUT1
CEx†
1
2
1
2
1
2
BE[3:0]
EA[21:2]
3
4
ED[31:0]
1
2
AOE
8
10
9
ARE
AWE
11
ARDY
† CEx stays active for seven minus the value of Read Hold cycles after the last access (DMA transfer or CPU access). For example, if read
HOLD = 1, then CEx stays active for six more cycles. This does not affect performance, it merely reflects the EMIF’s overhead.
Figure 16. Asynchronous Memory Read Timing (ARDY Used)
44
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2 Strobe = 3
Hold = 2
CLKOUT1
CEx†
12
13
12
13
12
13
12
13
BE[3:0]
EA[21:2]
ED[31:0]
AOE
15
ARE
16
ARDY
† If no write accesses are scheduled for the next cycle and write hold is set to 1 or greater, then CEx stays active for three cycles after the value
of the programmed hold period. If write hold is set to 0, then CEx stays active for four more cycles. This does not affect performance, it merely
reflects the EMIF’s overhead.
Figure 17. Asynchronous Memory Write Timing (ARDY Not Used)
Setup = 2 Strobe = 3
Not Ready
Hold = 2
CLKOUT1
12
13
12
13
12
13
12
13
CEx†
BE[3:0]
EA[21:2]
ED[31:0]
AOE
ARE
17
18
19
AWE
11
ARDY
† If no write accesses are scheduled for the next cycle and write hold is set to 1 or greater, then CEx stays active for three cycles after the value
of the programmed hold period. If write hold is set to 0, then CEx stays active for four more cycles. This does not affect performance, it merely
reflects the EMIF’s overhead.
Figure 18. Asynchronous Memory Write Timing (ARDY Used)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
45
PRODUCT PREVIEW
14
AWE
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
SYNCHRONOUS-BURST MEMORY TIMING
timing requirements for synchronous-burst SRAM cycles (see Figure 19)
C6203B-250
NO
NO.
7
8
MIN
tsu(EDV-CKO2H)
th(CKO2H-EDV)
C6203B-300
MAX
MIN
MAX
C6203C-300
MIN
MAX
UNIT
Setup time, read EDx valid before CLKOUT2 high
2.0
1.7
1.6
ns
Hold time, read EDx valid after CLKOUT2 high
2.0
1.5
2.3
ns
switching characteristics over recommended operating conditions for synchronous-burst SRAM
cycles†‡ (see Figure 19 and Figure 20)
C6203B-250
PRODUCT PREVIEW
NO
NO.
PARAMETER
MIN
1
tosu(CEV-CKO2H)
Output setup time, CEx valid before
CLKOUT2 high
2
toh(CKO2H-CEV)
Output hold time, CEx valid after
CLKOUT2 high
3
tosu(BEV-CKO2H)
Output setup time, BEx valid before
CLKOUT2 high
4
toh(CKO2H-BEIV)
Output hold time, BEx invalid after
CLKOUT2 high
5
tosu(EAV-CKO2H)
Output setup time, EAx valid before
CLKOUT2 high
6
toh(CKO2H-EAIV)
Output hold time, EAx invalid after
CLKOUT2 high
9
Output setup time, SDCAS/SSADS
tosu(ADSV-CKO2H)
valid before CLKOUT2 high
10
toh(CKO2H-ADSV)
11
MAX
C6203B-300
MIN
MAX
C6203C-300
MIN
MAX
UNIT
P – 0.8
P + 0.1
P–1
ns
P–3
P – 2.3
P – 2.7
ns
P – 0.8
P + 0.1
P–1
ns
P–3
P – 2.3
P – 2.7
ns
P – 0.8
P + 0.1
P–1
ns
P–3
P – 2.3
P – 2.7
ns
P – 0.8
P + 0.1
P–1
ns
Output hold time, SDCAS/SSADS
valid after CLKOUT2 high
P–3
P – 2.3
P – 2.7
ns
tosu(OEV-CKO2H)
Output setup time, SDRAS/SSOE
valid before CLKOUT2 high
P – 0.8
P + 0.1
P–1
ns
12
toh(CKO2H-OEV)
Output hold time, SDRAS/SSOE
valid after CLKOUT2 high
P–3
P – 2.3
P – 2.7
ns
13
tosu(EDV-CKO2H)
Output setup time, EDx valid before
CLKOUT2 high§
P – 1.2
P + 0.1
P – 1.6
ns
14
toh(CKO2H-EDIV)
Output hold time, EDx invalid after
CLKOUT2 high
P–3
P – 2.3
P – 2.5
ns
15
tosu(WEV-CKO2H)
Output setup time, SDWE/SSWE
valid before CLKOUT2 high
P – 0.8
P + 0.1
P–1
ns
16
toh(CKO2H-WEV)
Output hold time, SDWE/SSWE
valid after CLKOUT2 high
P–3
P – 2.3
P – 2.7
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
‡ SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM accesses.
§ For the first write in a series of one or more consecutive adjacent writes, the write data is generated one CLKOUT2 cycle early to accommodate
the ED enable time.
46
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
SYNCHRONOUS-BURST MEMORY TIMING (CONTINUED)
CLKOUT2
1
2
CEx
BE[3:0]
3
BE1
BE2
BE3
BE4
4
EA[21:2]
5
A1
A2
A3
A4
6
7
Q1
ED[31:0]
8
Q2
Q3
9
Q4
10
SDCAS/SSADS†
11
12
PRODUCT PREVIEW
SDRAS/SSOE†
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM accesses.
Figure 19. SBSRAM Read Timing
CLKOUT2
1
2
CEx
BE[3:0]
3
BE1
BE2
BE3
BE4
4
EA[21:2]
5
A1
A2
A3
A4
Q1
Q2
Q3
Q4
6
13
14
ED[31:0]
9
10
15
16
SDCAS/SSADS†
SDRAS/SSOE†
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM accesses.
Figure 20. SBSRAM Write Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
47
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
SYNCHRONOUS DRAM TIMING
timing requirements for synchronous DRAM cycles (see Figure 21)
C6203B-250
NO
NO.
7
8
MIN
tsu(EDV-CKO2H)
th(CKO2H-EDV)
MAX
C6203B-300
MIN
MAX
C6203C-300
MIN
MAX
UNIT
Setup time, read EDx valid before CLKOUT2 high
1.2
0.5
0
ns
Hold time, read EDx valid after CLKOUT2 high
2.7
2
2.3
ns
switching characteristics over recommended operating conditions for synchronous DRAM
cycles†‡ (see Figure 21–Figure 26)
C6203B-250
PRODUCT PREVIEW
NO
NO.
PARAMETER
MIN
MAX
C6203B-300
MIN
MAX
C6203C-300
MIN
MAX
UNIT
1
tosu(CEV-CKO2H)
Output setup time, CEx valid
before CLKOUT2 high
P – 0.9
P + 0.6
P–1
ns
2
toh(CKO2H-CEV)
Output hold time, CEx valid after
CLKOUT2 high
P – 2.9
P – 1.8
P – 2.3
ns
3
tosu(BEV-CKO2H)
Output setup time, BEx valid
before CLKOUT2 high
P – 0.9
P + 0.6
P–1
ns
4
toh(CKO2H-BEIV)
Output hold time, BEx invalid after
CLKOUT2 high
P – 2.9
P – 1.8
P – 2.3
ns
5
tosu(EAV-CKO2H)
Output setup time, EAx valid
before CLKOUT2 high
P – 0.9
P + 0.6
P–1
ns
6
toh(CKO2H-EAIV)
Output hold time, EAx invalid after
CLKOUT2 high
P – 2.9
P – 1.8
P – 2.3
ns
9
tosu(CASV-CKO2H)
Output setup time,
SDCAS/SSADS valid before
CLKOUT2 high
P – 0.9
P + 0.6
P–1
ns
10
toh(CKO2H-CASV)
Output hold time, SDCAS/SSADS
valid after CLKOUT2 high
P – 2.9
P – 1.8
P – 2.3
ns
11
tosu(EDV-CKO2H)
Output setup time, EDx valid
before CLKOUT2 high§
P – 1.5
P + 0.6
P – 1.6
ns
12
toh(CKO2H-EDIV)
Output hold time, EDx invalid after
CLKOUT2 high
P – 2.8
P – 1.8
P–2
ns
13
tosu(WEV-CKO2H)
Output setup time, SDWE/SSWE
valid before CLKOUT2 high
P – 0.9
P + 0.6
P–1
ns
14
toh(CKO2H-WEV)
Output hold time, SDWE/SSWE
valid after CLKOUT2 high
P – 2.9
P – 1.8
P – 2.3
ns
15
tosu(SDA10V-CKO2H)
Output setup time, SDA10 valid
before CLKOUT2 high
P – 0.9
P + 0.6
P–1
ns
16
toh(CKO2H-SDA10IV)
Output hold time, SDA10 invalid
after CLKOUT2 high
P – 2.9
P – 1.8
P – 2.3
ns
17
tosu(RASV-CKO2H)
Output setup time, SDRAS/SSOE
valid before CLKOUT2 high
P – 0.9
P + 0.6
P–1
ns
18
toh(CKO2H-RASV)
Output hold time, SDRAS/SSOE
valid after CLKOUT2 high
P – 2.9
P – 1.8
P – 2.3
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
‡ SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
§ For the first write in a series of one or more consecutive adjacent writes, the write data is generated one CLKOUT2 cycle early to accommodate
the ED enable time.
48
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
SYNCHRONOUS DRAM TIMING (CONTINUED)
READ
READ
READ
CLKOUT2
1
2
CEx
3
BE[3:0]
5
EA[15:2]
4
BE1
BE2
CA2
CA3
BE3
6
CA1
7
8
D1
ED[31:0]
15
16
9
10
D2
D3
SDA10
PRODUCT PREVIEW
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 21. Three SDRAM READ Commands
WRITE
WRITE
WRITE
CLKOUT2
1
2
CEx
3
BE[3:0]
4
BE1
5
EA[15:2]
BE3
CA2
CA3
D2
D3
6
CA1
11
D1
ED[31:0]
BE2
12
15
16
9
10
13
14
SDA10
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 22. Three SDRAM WRT Commands
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
49
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
SYNCHRONOUS DRAM TIMING (CONTINUED)
ACTV
CLKOUT2
1
2
CEx
BE[3:0]
5
Bank Activate/Row Address
EA[15:2]
ED[31:0]
15
Row Address
SDA10
17
18
PRODUCT PREVIEW
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 23. SDRAM ACTV Command
DCAB
CLKOUT2
1
2
15
16
17
18
CEx
BE[3:0]
EA[15:2]
ED[31:0]
SDA10
SDRAS/SSOE†
SDCAS/SSADS†
13
14
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 24. SDRAM DCAB Command
50
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
SYNCHRONOUS DRAM TIMING (CONTINUED)
REFR
CLKOUT2
1
2
CEx
BE[3:0]
EA[15:2]
ED[31:0]
SDA10
17
18
SDRAS/SSOE†
9
10
PRODUCT PREVIEW
SDCAS/SSADS†
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 25. SDRAM REFR Command
MRS
CLKOUT2
1
2
5
6
CEx
BE[3:0]
EA[15:2]
MRS Value
ED[31:0]
SDA10
17
18
9
10
13
14
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
† SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 26. SDRAM MRS Command
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
51
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
HOLD/HOLDA TIMING
timing requirements for the HOLD/HOLDA cycles† (see Figure 27)
C6203B-250
C6203B-300
C6203C-300
NO.
MIN
3
toh(HOLDAL-HOLDL) Output hold time, HOLD low after HOLDA low
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
UNIT
MAX
P
ns
switching characteristics over recommended operating conditions for the HOLD/HOLDA cycles†‡
(see Figure 27)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
PRODUCT PREVIEW
1
2
4
5
td(HOLDL-EMHZ)
td(EMHZ-HOLDAL)
Delay time, HOLD low to EMIF Bus high impedance
td(HOLDH-EMLZ)
td(EMLZ-HOLDAH)
Delay time, HOLD high to EMIF Bus low impedance
Delay time, EMIF Bus high impedance to HOLDA low
UNIT
3P
MAX
§
ns
0
2P
ns
3P
7P
ns
Delay time, EMIF Bus low impedance to HOLDA high
0
2P
External Requestor
Owns Bus
DSP Owns Bus
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
‡ EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE, AOE, AWE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE, and SDA10.
§ All pending EMIF transactions are allowed to complete before HOLDA is asserted. The worst case for this is an asynchronous read or write with
external ARDY used or a minimum of eight consecutive SDRAM reads or writes when RBTR8 = 1. If no bus transactions are occurring, then the
minimum delay time can be achieved. Also, bus hold can be indefinitely delayed by setting NOHOLD = 1.
DSP Owns Bus
3
HOLD
2
5
HOLDA
EMIF Bus†
1
4
C6203B/03C
C6203B/03C
† EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE, AOE, AWE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE, and SDA10.
Figure 27. HOLD/HOLDA Timing
52
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
RESET TIMING
timing requirements for reset† (see Figure 28)
C6203B-250
C6203B-300
C6203C-300
MIN
MAX
Width of the RESET pulse (PLL stable)‡
10P
ns
250
µs
5P
ns
1
tw(RST)
Width of the RESET pulse (PLL needs to sync up)§
10
tsu(XD)
th(XD)
Setup time, XD configuration bits valid before RESET high¶
Hold time, XD configuration bits valid after RESET high¶
11
UNIT
5P
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
‡ This parameter applies to CLKMODE x1 when CLKIN is stable, and applies to CLKMODE x4, x6, x7, x8, x9, x10, and x11 when CLKIN and PLL
are stable for C6203B. And applies to CLKMODE x4, x6, x8, and x12 when CLKIN and PLL are stable for C6203C.
§ This parameter applies to CLKMODE x4, x6, x7, x8, x9, x10, and x11 only (it does not apply to CLKMODE x1) for C6203B. This parameter applies
to CLKMODE x4, x6, x8, and x12 only (it does not apply to CLKMODE x1) for C6203C. The RESET signal is not connected internally to the clock
PLL circuit. The PLL, however, may need up to 250 µs to stabilize following device power up or after PLL configuration has been changed. During
that time, RESET must be asserted to ensure proper device operation. See the Clock PLL section for PLL lock times.
¶ XD[31:0] are the boot configuration pins during device reset.
switching characteristics over recommended operating conditions during reset†# (see Figure 28)
NO.
PARAMETER
C6203B-250
C6203B-300
C6203C-300
MIN
2
3
4
5
6
7
8
9
td(RSTL-CKO2IV)
td(RSTH-CKO2V)
Delay time, RESET low to CLKOUT2 invalid
td(RSTL-HIGHIV)
td(RSTH-HIGHV)
Delay time, RESET low to high group invalid
td(RSTL-LOWIV)
td(RSTH-LOWV)
Delay time, RESET low to low group invalid
td(RSTL-ZHZ)
td(RSTH-ZV)
Delay time, RESET low to Z group high impedance
ns
4P
P
Delay time, RESET high to high group valid
ns
ns
4P
P
Delay time, RESET high to low group valid
Delay time, RESET high to Z group valid
MAX
P
Delay time, RESET high to CLKOUT2 valid
UNIT
ns
ns
4P
P
ns
ns
4P
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
# High group consists of:
XFCLK, HOLDA
Low group consists of:
IACK, INUM[3:0], DMAC[3:0], PD, TOUT0, and TOUT1
Z group consists of:
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE, AWE, AOE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE,
SDA10, CLKX0, CLKX1, CLKX2, FSX0, FSX1, FSX2, DX0, DX1, DX2, CLKR0, CLKR1, CLKR2, FSR0, FSR1,
FSR2, XCE[3:0], XBE[3:0]/XA[5:2], XOE, XRE, XWE/XWAIT, XAS, XW/R, XRDY, XBLAST, XHOLD,
and XHOLDA
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
53
PRODUCT PREVIEW
NO.
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
RESET TIMING (CONTINUED)
CLKOUT1
1
10
11
RESET
2
3
4
5
6
7
8
9
CLKOUT2
HIGH GROUP†
LOW GROUP†
Z GROUP†
Boot Configuration
PRODUCT PREVIEW
XD[31:0]‡
† High group consists of:
Low group consists of:
Z group consists of:
XFCLK, HOLDA
IACK, INUM[3:0], DMAC[3:0], PD, TOUT0, and TOUT1.
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE, AWE, AOE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE,
SDA10, CLKX0, CLKX1, CLKX2, FSX0, FSX1, FSX2, DX0, DX1, DX2, CLKR0, CLKR1, CLKR2, FSR0, FSR1,
FSR2, XCE[3:0], XBE[3:0]/XA[5:2], XOE, XRE, XWE/XWAIT, XAS, XW/R, XRDY, XBLAST, XHOLD,
and XHOLDA.
‡ XD[31:0] are the boot configuration pins during device reset.
Figure 28. Reset Timing
54
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXTERNAL INTERRUPT TIMING
timing requirements for interrupt response cycles† (see Figure 29)
C6203B-250
C6203B-300
C6203C-300
NO.
MIN
2
3
tw(ILOW)
tw(IHIGH)
UNIT
MAX
Width of the interrupt pulse low
2P
ns
Width of the interrupt pulse high
2P
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
switching characteristics over recommended operating conditions during interrupt response
cycles†‡ (see Figure 29)
PARAMETER
MIN
1
4
5
UNIT
MAX
tR(EINTH – IACKH)
td(CKO2L-IACKV)
Response time, EXT_INTx high to IACK high
Delay time, CLKOUT2 low to IACK valid
–1.5
9P
10
ns
ns
td(CKO2L-INUMV)
td(CKO2L-INUMIV)
Delay time, CLKOUT2 low to INUMx valid
–2.0
10
ns
6
Delay time, CLKOUT2 low to INUMx invalid
–2.0
10
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.33 ns.
‡ When CLKOUT2 is in half (1/2) mode (see CLKOUT2 in Signal Descriptions table), timings are based on falling edges (C6203B and C6203C).
When CLKOUT2 is in quarter (1/4) mode (see CLKOUT2 in Signal Descriptions table), timings are based on rising or falling edges (C6203C only).
CLKOUT2 (1/4)
[C6203C only]
1
CLKOUT2 (1/2)
2
3
EXT_INTx, NMI
Intr Flag
4
4
IACK
5
INUMx
6
Interrupt Number
Figure 29. Interrupt Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
55
PRODUCT PREVIEW
NO.
C6203B-250
C6203B-300
C6203C-300
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS FIFO TIMING
timing requirements for synchronous FIFO interface (see Figure 30, Figure 31, and Figure 32)
NO.
5
6
tsu(XDV-XFCKH)
th(XFCKH-XDV)
C6203B-250
C6203B-300
C6203C-300
MIN
MIN
Setup time, read XDx valid before XFCLK high
Hold time, read XDx valid after XFCLK high
MAX
UNIT
MAX
3
2.5
ns
2.5
2
ns
switching characteristics over recommended operating conditions for synchronous FIFO
interface (see Figure 30, Figure 31, and Figure 32)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
1
PRODUCT PREVIEW
2
3
4
7
8
MAX
td(XFCKH-XCEV)
td(XFCKH-XAV)
Delay time, XFCLK high to XCEx valid
1.5
4.5
ns
Delay time, XFCLK high to XBE[3:0]/XA[5:2] valid†
1.5
4.5
ns
td(XFCKH-XOEV)
td(XFCKH-XREV)
Delay time, XFCLK high to XOE valid
1.5
4.5
ns
Delay time, XFCLK high to XRE valid
1.5
4.5
ns
td(XFCKH-XWEV)
td(XFCKH-XDV)
Delay time, XFCLK high to XWE/XWAIT‡ valid
1.5
4.5
ns
4.5
ns
Delay time, XFCLK high to XDx valid
9
td(XFCKH-XDIV)
Delay time, XFCLK high to XDx invalid
† XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
1.5
ns
XFCLK
1
1
XCE3†
2
XBE[3:0]/XA[5:2]‡
2
XA1
XA2
XA3
XA4
3
3
XOE
4
4
XRE
XWE/XWAIT§
6
5
XD[31:0]
D1
D2
D3
† FIFO read (glueless) mode only available in XCE3.
‡ XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
§ XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
Figure 30. FIFO Read Timing (Glueless Read Mode)
56
UNIT
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
D4
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS FIFO TIMING (CONTINUED)
XFCLK
1
1
XCEx
2
XBE[3:0]/XA[5:2]†
2
XA1
XA2
XA3
XA4
3
3
XOE
4
4
XRE
XWE/XWAIT‡
6
5
XD[31:0]
D1
D2
D3
D4
PRODUCT PREVIEW
† XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
Figure 31. FIFO Read Timing
XFCLK
1
1
XCEx
2
XBE[3:0]/XA[5:2]†
2
XA1
XA2
XA3
XA4
XOE
XRE
7
7
XWE/XWAIT‡
9
8
XD[31:0]
D1
D2
D3
D4
† XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
Figure 32. FIFO Write Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
57
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING
timing requirements for asynchronous peripheral cycles†‡§¶ (see Figure 33–Figure 36)
C6203B-250
C6203B-300
NO.
PRODUCT PREVIEW
MIN
C6203C-300
MAX
MIN
UNIT
MAX
3
tsu(XDV-XREH)
Setup time, XDx valid before XRE
high
4.5
3
ns
4
th(XREH-XDV)
Hold time, XDx valid after XRE high
2.5
1
ns
6
tsu(XRDYH-XREL)
Setup time, XRDY high before XRE
low
–[(RST – 3) * P – 6]
–[(RST – 3) * P – 6]
ns
7
th(XREL-XRDYH)
Hold time, XRDY high after XRE low
(RST – 3) * P + 2
(RST – 3) * P + 2
ns
9
tsu(XRDYL-XREL)
Setup time, XRDY low before XRE
low
–[(RST – 3) * P – 6]
–[(RST – 3) * P – 6]
ns
10
th(XREL-XRDYL)
Hold time, XRDY low after XRE low
(RST – 3) * P + 2
(RST – 3) * P + 2
ns
11
tw(XRDYH)
Pulse width, XRDY high
2P
2P
ns
15
tsu(XRDYH-XWEL)
Setup time, XRDY high before XWE
low
–[(WST – 3) * P – 6]
–[(WST – 3) * P – 6]
ns
16
th(XWEL-XRDYH)
Hold time, XRDY high after XWE
low
(WST – 3) * P + 2
(WST – 3) * P + 2
ns
18
tsu(XRDYL-XWEL)
Setup time, XRDY low before XWE
low
–[(WST – 3) * P – 6]
–[(WST – 3) * P – 6]
ns
19
th(XWEL-XRDYL)
Hold time, XRDY low after XWE low
(WST – 3) * P + 2
(WST – 3) * P + 2
ns
† To ensure data setup time, simply program the strobe width wide enough. XRDY is internally synchronized. If XRDY does meet setup or hold
time, it may be recognized in the current cycle or the next cycle. Thus, XRDY can be an asynchronous input.
‡ RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the XBUS XCE space control registers.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
¶ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use XRDY input to extend strobe width.
58
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING (CONTINUED)
switching characteristics over recommended operating conditions for asynchronous peripheral
cycles†‡§¶ (see Figure 33–Figure 36)
C6203B-250
C6203B-300
PARAMETER
MIN
TYP
C6203C-300
MAX
MIN
TYP
UNIT
MAX
1
tosu(SELV-XREL)
Output setup time, select
signals valid to XRE low
RS * P – 2
RS * P – 1
ns
2
toh(XREH-SELIV)
Output hold time, XRE low to
select signals invalid
RH * P – 2
RH * P – 1
ns
5
tw(XREL)
Pulse width, XRE low
8
td(XRDYH-XREH)
Delay time, XRDY high to XRE
high
12
tosu(SELV-XWEL)
Output setup time, select
signals valid to XWE low
WS * P – 3
WS * P – 1
ns
13
toh(XWEH-SELIV)
Output hold time, XWE low to
select signals invalid
WH * P – 2
WH * P – 1
ns
14
tw(XWEL)
Pulse width, XWE low
17
td(XRDYH-XWEH)
Delay time, XRDY high to XWE
high
RST * P
3P
RST * P
4P + 5
3P
WST * P
3P
ns
4P + 3
WST * P
4P + 5
3P
ns
ns
4P + 3
ns
† RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the XBUS XCE space control registers.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
§ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use XRDY input to extend strobe width.
¶ Select signals include: XCEx, XBE[3:0]/XA[5:2], XOE; and for writes, include XD[31:0], with the exception that XCEx can stay active for an
additional 7P ns following the end of the cycle.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
59
PRODUCT PREVIEW
NO.
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING (CONTINUED)
Setup = 2
Strobe = 3
Hold = 2
CLKOUT1
1
2
1
2
XCEx
XBE[3:0]/
XA[5:2]†
3
4
XD[31:0]
1
2
XOE
5
6
7
PRODUCT PREVIEW
XRE
XWE/XWAIT‡
XRDY§
† XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
Figure 33. Expansion Bus Asynchronous Peripheral Read Timing (XRDY Not Used)
Setup = 2
Strobe = 3
Not Ready
Hold = 2
CLKOUT1
1
2
1
2
XCEx
XBE[3:0]/
XA[5:2]†
3
4
XD[31:0]
1
2
XOE
8
10
9
XRE
XWE/XWAIT‡
11
XRDY§
† XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
Figure 34. Expansion Bus Asynchronous Peripheral Read Timing (XRDY Used)
60
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING (CONTINUED)
Setup = 2
Strobe = 3
Hold = 2
CLKOUT1
12
13
12
13
12
13
XCEx
XBE[3:0]/
XA[5:2]†
XD[31:0]
XOE
XRE
15
16
14
XWE/XWAIT‡
PRODUCT PREVIEW
XRDY§
† XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
Figure 35. Expansion Bus Asynchronous Peripheral Write Timing (XRDY Not Used)
Setup = 2 Strobe = 3
Not Ready
Hold = 2
CLKOUT1
12
13
12
13
12
13
XCEx
XBE[3:0]/
XA[5:2]†
XD[31:0]
XOE
XRE
17
18
19
XWE/XWAIT‡
11
XRDY§
† XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
Figure 36. Expansion Bus Asynchronous Peripheral Write Timing (XRDY Used)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
61
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING
timing requirements with external device as bus master (see Figure 37 and Figure 38)
NO.
1
2
3
4
5
6
7
8
9
PRODUCT PREVIEW
10
16
17
18
C6203B-250
C6203B-300
C6203C-300
MIN
MIN
MAX
UNIT
MAX
tsu(XCSV-XCKIH)
th(XCKIH-XCS)
Setup time, XCS valid before XCLKIN high
3.5
4
ns
Hold time, XCS valid after XCLKIN high
2.8
2.3
ns
tsu(XAS-XCKIH)
th(XCKIH-XAS)
Setup time, XAS valid before XCLKIN high
3.5
4
ns
Hold time, XAS valid after XCLKIN high
2.8
2.3
ns
tsu(XCTL-XCKIH)
th(XCKIH-XCTL)
Setup time, XCNTL valid before XCLKIN high
3.5
4
ns
Hold time, XCNTL valid after XCLKIN high
2.8
2.3
ns
tsu(XWR-XCKIH)
th(XCKIH-XWR)
Setup time, XW/R valid before XCLKIN high†
Hold time, XW/R valid after XCLKIN high†
3.5
4
ns
2.8
2.3
ns
tsu(XBLTV-XCKIH)
th(XCKIH-XBLTV)
Setup time, XBLAST valid before XCLKIN high‡
Hold time, XBLAST valid after XCLKIN high‡
3.5
4
ns
2.8
2.3
ns
tsu(XBEV-XCKIH)
th(XCKIH-XBEV)
Setup time, XBE[3:0]/XA[5:2] valid before XCLKIN high§
Hold time, XBE[3:0]/XA[5:2] valid after XCLKIN high§
3.5
4
ns
2.8
2.3
ns
tsu(XD-XCKIH)
th(XCKIH-XD)
Setup time, XDx valid before XCLKIN high
3.5
4
ns
2.8
2.3
ns
19
Hold time, XDx valid after XCLKIN high
† XW/R input/output polarity selected at boot.
‡ XBLAST input polarity selected at boot
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
switching characteristics over recommended operating conditions with external device as bus
master¶ (see Figure 37 and Figure 38)
NO.
C6203B-250
C6203B-300
PARAMETER
MIN
11
C6203C-300
MAX
UNIT
MAX
td(XCKIH-XDLZ)
td(XCKIH-XDV)
Delay time, XCLKIN high to XDx low impedance
td(XCKIH-XDIV)
td(XCKIH-XDHZ)
Delay time, XCLKIN high to XDx invalid
5
Delay time, XCLKIN high to XDx high impedance
Delay time, XCLKIN high to XRDY invalid#
4P
ns
5
16.5
3
4P – 0.5
ns
Delay time, XCLKIN high to XRDY low impedance
5
16.5
3
4P – 0.5
ns
21
td(XCKIH-XRYHZ)
2P + 5
¶ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
# XRDY operates as active-low ready input/output during host-port accesses.
3P + 16.5
2P + 3
7P – 0.5
ns
12
13
14
15
20
td(XCKIH-XRY)
td(XCKIH-XRYLZ)
Delay time, XCLKIN high to XDx valid
Delay time, XCLKIN high to XRDY high impedance#
62
0
MIN
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
0
16.5
ns
4P – 0.5
3
4P
ns
ns
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
2
1
XCS
4
3
XAS
6
5
XCNTL
8
7
XW/R†
8
7
XW/R†
XBE[3:0]/XA[5:2]‡
10
9
XBLAST§
PRODUCT PREVIEW
10
9
XBLAST§
13
14
12
11
D1
XD[31:0]
20
D2
15
D3
D4
15
21
XRDY¶
† XW/R input/output polarity selected at boot
‡ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
§ XBLAST input polarity selected at boot
¶ XRDY operates as active-low ready input/output during host-port accesses.
Figure 37. External Host as Bus Master—Read
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
63
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
2
1
XCS
4
3
XAS
6
5
XCNTL
8
7
XW/R†
8
7
XW/R†
17
16
XBE[3:0]/XA[5:2]‡
XBE1
XBE2
XBE3
XBE4
10
PRODUCT PREVIEW
9
XBLAST§
10
9
XBLAST§
19
18
D1
XD[31:0]
20
D2
D3
15
XRDY¶
† XW/R input/output polarity selected at boot
‡ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
§ XBLAST input polarity selected at boot
¶ XRDY operates as active-low ready input/output during host-port accesses.
Figure 38. External Host as Bus Master—Write
64
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
D4
15
21
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
timing requirements with C62x as bus master (see Figure 39, Figure 40, and Figure 41)
NO.
9
10
11
12
14
15
C6203B-250
C6203B-300
C6203C-300
MIN
MIN
MAX
UNIT
MAX
tsu(XDV-XCKIH)
th(XCKIH-XDV)
Setup time, XDx valid before XCLKIN high
3.5
4
ns
Hold time, XDx valid after XCLKIN high
2.8
2.3
ns
tsu(XRY-XCKIH)
th(XCKIH-XRY)
Setup time, XRDY valid before XCLKIN high†
Hold time, XRDY valid after XCLKIN high†
3.5
4
ns
2.8
2.3
ns
tsu(XBFF-XCKIH)
th(XCKIH-XBFF)
Setup time, XBOFF valid before XCLKIN high
3.5
4
ns
Hold time, XBOFF valid after XCLKIN high
2.8
2.3
ns
† XRDY operates as active-low ready input/output during host-port accesses.
NO.
C6203B-250
C6203B-300
PARAMETER
MIN
1
2
3
4
5
6
7
8
MAX
C6203C-300
MIN
UNIT
MAX
td(XCKIH-XASV)
td(XCKIH-XWRV)
Delay time, XCLKIN high to XAS valid
5
16.5
3 4P – 0.5
ns
Delay time, XCLKIN high to XW/R valid§
5
16.5
3 4P – 0.5
ns
td(XCKIH-XBLTV)
td(XCKIH-XBEV)
Delay time, XCLKIN high to XBLAST valid¶
5
16.5
3 4P – 0.5
ns
Delay time, XCLKIN high to XBE[3:0]/XA[5:2] valid#
5
16.5
3 4P – 0.5
ns
td(XCKIH-XDLZ)
td(XCKIH-XDV)
Delay time, XCLKIN high to XDx low impedance
0
0
ns
td(XCKIH-XDIV)
td(XCKIH-XDHZ)
Delay time, XCLKIN high to XDx invalid
Delay time, XCLKIN high to XDx valid
16.5
5
Delay time, XCLKIN high to XDx high impedance
Delay time, XCLKIN high to XWE/XWAIT valid||
13
td(XCKIH-XWTV)
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
§ XW/R input/output polarity selected at boot.
¶ XBLAST output polarity is always active low.
# XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
|| XWE/XWAIT operates as XWAIT output signal during host-port accesses.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
5
4P – 0.5
3
ns
ns
4P
4P
ns
16.5
3 4P – 0.5
ns
65
PRODUCT PREVIEW
switching characteristics over recommended operating conditions with C62x as bus master‡
(see Figure 39, Figure 40, and Figure 41)
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
1
1
XAS
2
2
XW/R†
XW/R†
3
3
XBLAST‡
4
4
XBE[3:0]/XA[5:2]§
5
7
6
AD
XD[31:0]
BE
9
8
D1
10
D2
D3
D4
11
12
PRODUCT PREVIEW
XRDY
13
13
XWE/XWAIT¶
† XW/R input/output polarity selected at boot
‡ XBLAST output polarity is always active low.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
¶ XWE/XWAIT operates as XWAIT output signal during host-port accesses.
Figure 39. C62x as Bus Master—Read
XCLKIN
1
1
XAS
XW/R†
2
2
XW/R†
3
3
XBLAST‡
4
4
6
7
XBE[3:0]/XA[5:2]§
5
XD[31:0]
Addr
8
D1
D2
D3
D4
11
XRDY
12
13
13
XWE/XWAIT¶
† XW/R input/output polarity selected at boot
‡ XBLAST output polarity is always active low.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
¶ XWE/XWAIT operates as XWAIT output signal during host-port accesses.
Figure 40. C62x as Bus Master—Write
66
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
1
1
XAS
XW/R†
2
2
4
4
XW/R†
XBLAST‡
XBE[3:0]/XA[5:2]§
6
7
5
XD[31:0]
8
Addr
D1
11
D2
12
XRDY
15
PRODUCT PREVIEW
14
XBOFF
XHOLD¶
XHOLDA¶
XHOLD#
XHOLDA#
† XW/R input/output polarity selected at boot
‡ XBLAST output polarity is always active low.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
¶ Internal arbiter enabled
# External arbiter enabled
|| This diagram illustrates XBOFF timing. Bus arbitration timing is shown in Figure 44 and Figure 45.
Figure 41. C62x as Bus Master—BOFF Operation||
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
67
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS ASYNCHRONOUS HOST-PORT TIMING
timing requirements with external device as asynchronous bus master† (see Figure 42 and
Figure 43)
NO.
C6203C-300
MIN
MIN
MAX
UNIT
MAX
1
tw(XCSL)
Pulse duration, XCS low
4P
4P
ns
2
tw(XCSH)
Pulse duration, XCS high
4P
4P
ns
3
tsu(XSEL-XCSL)
Setup time, expansion bus select signals‡ valid before XCS
low
1
2
ns
4
th(XCSL-XSEL)
th(XRYL-XCSL)
Hold time, expansion bus select signals‡ valid after XCS low
tsu(XBEV-XCSH)
th(XCSH-XBEV)
tsu(XDV-XCSH)
th(XCSH-XDV)
10
11
12
13
PRODUCT PREVIEW
C6203B-250
C6203B-300
14
3.4
2
ns
P + 1.5
P
ns
Setup time, XBE[3:0]/XA[5:2] valid before XCS high§
Hold time, XBE[3:0]/XA[5:2] valid after XCS high§
1
2
ns
3
2
ns
Setup time, XDx valid before XCS high
1
2
ns
Hold time, XDx valid after XCS high
3
2
ns
Hold time, XCS low after XRDY low
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ Expansion bus select signals include XCNTL and XR/W.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
switching characteristics over recommended operating conditions with external device as
asynchronous bus master† (see Figure 42 and Figure 43)
NO.
5
6
7
8
PARAMETER
C6203C-300
MIN
MIN
td(XCSL-XDLZ)
td(XCSH-XDIV)
Delay time, XCS low to XDx low impedance
0
Delay time, XCS high to XDx invalid
0
td(XCSH-XDHZ)
td(XRYL-XDV)
Delay time, XCS high to XDx high impedance
Delay time, XRDY low to XDx valid
9
td(XCSH-XRYH)
Delay time, XCS high to XRDY high
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
68
C6203B-250
C6203B-300
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
MAX
0
12
0
4P
UNIT
MAX
ns
12
ns
4P
ns
–4
1
0
4
ns
0
12
0
12
ns
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
EXPANSION BUS ASYNCHRONOUS HOST-PORT TIMING (CONTINUED)
1
1
2
10
10
XCS
3
3
4
4
XCNTL
XBE[3:0]/XA[5:2]†
3
3
4
4
XR/W‡
3
3
4
4
XR/W‡
5
7
6
8
5
7
6
8
Word
XD[31:0]
9
9
PRODUCT PREVIEW
XRDY
† XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
‡ XW/R input/output polarity selected at boot
Figure 42. External Device as Asynchronous Master—Read
1
10
2
10
1
XCS
3
3
4
4
XCNTL
11
11
12
12
XBE[3:0]/XA[5:2]†
3
3
4
4
XR/W‡
3
3
4
4
XR/W‡
13
XD[31:0]
14
13
14
word
Word
9
9
XRDY
† XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
‡ XW/R input/output polarity selected at boot
Figure 43. External Device as Asynchronous Master—Write
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
69
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
XHOLD/XHOLDA TIMING
timing requirements for expansion bus arbitration (internal arbiter enabled)† (see Figure 44)
C6203B-250
C6203B-300
C6203C-300
NO.
MIN
3
toh(XHDAH-XHDH)
Output hold time, XHOLD high after XHOLDA high
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
UNIT
MAX
P
ns
switching characteristics over recommended operating conditions for expansion bus arbitration
(internal arbiter enabled)†‡ (see Figure 44)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
1
PRODUCT PREVIEW
2
4
td(XHDH-XBHZ)
td(XBHZ-XHDAH)
Delay time, XHOLD high to XBus high impedance
td(XHDL-XHDAL)
td(XHDAL-XBLZ)
Delay time, XHOLD low to XHOLDA low
Delay time, XBus high impedance to XHOLDA high
External Requestor
Owns Bus
DSP Owns Bus
3P
MAX
§
ns
0
2P
ns
3P
5
Delay time, XHOLDA low to XBus low impedance
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
§ All pending XBus transactions are allowed to complete before XHOLDA is asserted.
0
DSP Owns Bus
3
XHOLD (input)
2
4
XHOLDA (output)
1
XBus†
5
C6203B/03C
C6203B/03C
† XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
Figure 44. Expansion Bus Arbitration—Internal Arbiter Enabled
70
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
UNIT
ns
2P
ns
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
XHOLD/XHOLDA TIMING (CONTINUED)
switching characteristics over recommended operating conditions for expansion bus arbitration
(internal arbiter disabled)† (see Figure 45)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
1
2
td(XHDAH-XBLZ)
td(XBHZ-XHDL)
Delay time, XHOLDA high to XBus low impedance‡
Delay time, XBus high impedance to XHOLD low‡
MAX
2P 2P + 10
0
UNIT
2P
ns
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
2
XHOLD (output)
XHOLDA (input)
PRODUCT PREVIEW
1
C6203B/03C
XBus†
† XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
Figure 45. Expansion Bus Arbitration—Internal Arbiter Disabled
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
71
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING
timing requirements for McBSP†‡ (see Figure 46)
C6203B-250
C6203B-300
NO.
2
PRODUCT PREVIEW
3
tc(CKRX)
tw(CKRX)
Cycle time, CLKR/X
Pulse duration, CLKR/X high or CLKR/X low
5
tsu(FRH-CKRL)
Setup time,
time external FSR high before CLKR low
6
th(CKRL-FRH)
Hold time,
time external FSR high after CLKR low
7
tsu(DRV-CKRL)
Setup time,
time DR valid before CLKR low
8
th(CKRL-DRV)
time DR valid after CLKR low
Hold time,
10
tsu(FXH-CKXL)
Setup time,
time external FSX high before CLKX low
11
th(CKXL-FXH)
Hold time,
time external FSX high after CLKX low
MAX
C6203C-300
CLKR/X ext
MIN
2P§
MIN
2P§
CLKR/X ext
P – 1¶
P – 1¶
CLKR int
9
9
CLKR ext
2
0
CLKR int
6
6
CLKR ext
3
3
CLKR int
8
8
CLKR ext
0.5
0
CLKR int
3
3
CLKR ext
4.5
3
CLKX int
9
9
CLKX ext
2
1
CLKX int
6
6
CLKX ext
4
3
UNIT
MAX
ns
ns
ns
ns
ns
ns
ns
ns
† CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
§ The maximum bit rate for the C6203B/03C device is 100 Mbps or CPU/2 (the slower of the two). Care must be taken to ensure that the AC timings
specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP communications is 100 MHz; therefore, the minimum CLKR/X
clock cycle is either twice the CPU cycle time (2P), or 10 ns (100 MHz), whichever value is larger. For example, when running parts at 300 MHz
(P = 3.3 ns), use 10 ns as the minimum CLKR/X clock cycle (by setting the appropriate CLKGDV ratio or external clock source). When running
parts at 100 MHz (P = 10 ns), use 2P = 20 ns (50 MHz) as the minimum CLKR/X clock cycle. The maximum bit rate for McBSP-to-McBSP
communications applies when the serial port is a master of the clock and frame syncs (with CLKR connected to CLKX, FSR connected to FSX,
CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY = 01b or 10b) and the other device the McBSP
communicates to is a slave.
¶ The minimum CLKR/X pulse duration is either (P – 1) or 4 ns, whichever is larger. For example, when running parts at 300 MHz (P = 3.3 ns), use
4 ns as the minimum CLKR/X pulse duration. When running parts at 100 MHz (P = 10 ns), use (P – 1) = 9 ns as the minimum CLKR/X pulse
duration.
72
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
switching characteristics over recommended operating conditions for McBSP†‡ (see Figure 46)
C6203B-250
C6203B-300
PARAMETER
C6203C-300
UNIT
MIN
MAX
MIN
MAX
4
16
4
10
1
td(CKSH-CKRXH)
Delay time, CLKS high to CLKR/X high for
internal
CLKR/X generated from CLKS input
2
tc(CKRX)
Cycle time, CLKR/X
CLKR/X int
2P§¶
3
tw(CKRX)
Pulse duration, CLKR/X high or CLKR/X
low
CLKR/X int
C – 1#
C + 1#
C – 1#
C + 1#
ns
4
td(CKRH-FRV)
Delay time, CLKR high to internal FSR
valid
CLKR int
–2
3
0
3
ns
–2
3
0
3
td(CKXH-FXV)
Delay time, CLKX high to internal FSX
valid
CLKX int
9
CLKX ext
3
9
3
9
–1
5
0
3
tdis(CKXH-DXHZ)
Disable time, DX high im
impedance
edance following
last data bit from CLKX high
CLKX int
12
CLKX ext
2
9
3
9
CLKX int
–0.5
4
0
3
13
td(CKXH-DXV)
Delay time,
time CLKX high to DX valid
CLKX ext
2
11
3
9
–1
5
0
3
td(FXH-DXV)
Delay time, FSX high to DX valid
ONLY applies when in data delay 0
(XDATDLY = 00b) mode.
FSX int
14
FSX ext
0
10
3
9
2P§¶
ns
ns
ns
ns
ns
ns
† CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
‡ Minimum delay times also represent minimum output hold times.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
¶ The maximum bit rate for the C6203B/03C device is 100 Mbps or CPU/2 (the slower of the two). Care must be taken to ensure that the AC timings
specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP communications is 100 MHz; therefore, the minimum CLKR/X
clock cycle is either twice the CPU cycle time (2P), or 10 ns (100 MHz), whichever value is larger. For example, when running parts at 300 MHz
(P = 3.3 ns), use 10 ns as the minimum CLKR/X clock cycle (by setting the appropriate CLKGDV ratio or external clock source). When running
parts at 100 MHz (P = 10 ns), use 2P = 20 ns (50 MHz) as the minimum CLKR/X clock cycle. The maximum bit rate for McBSP-to-McBSP
communications applies when the serial port is a master of the clock and frame syncs (with CLKR connected to CLKX, FSR connected to FSX,
CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY = 01b or 10b) and the other device the McBSP
communicates to is a slave.
# C = H or L
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
73
PRODUCT PREVIEW
NO.
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKS
1
2
3
3
CLKR
4
4
FSR (int)
5
6
FSR (ext)
7
DR
8
Bit(n-1)
(n-2)
(n-3)
2
3
3
CLKX
PRODUCT PREVIEW
9
FSX (int)
11
10
FSX (ext)
FSX (XDATDLY=00b)
12
DX
Bit 0
14
13
Bit(n-1)
13
(n-2)
Figure 46. McBSP Timings
74
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
(n-3)
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for FSR when GSYNC = 1 (see Figure 47)
C6203B-250
C6203B-300
C6203C-300
NO.
MIN
2
tsu(FRH-CKSH)
th(CKSH-FRH)
MAX
Setup time, FSR high before CLKS high
4
ns
Hold time, FSR high after CLKS high
4
ns
CLKS
1
2
FSR external
CLKR/X (no need to resync)
CLKR/X (needs resync)
PRODUCT PREVIEW
1
UNIT
Figure 47. FSR Timing When GSYNC = 1
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
75
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 48)
C6203B-250
C6203B-300
C6203C-300
NO.
MASTER
MIN
4
tsu(DRV-CKXL)
th(CKXL-DRV)
Setup time, DR valid before CLKX low
MAX
12
5
Hold time, DR valid after CLKX low
4
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
UNIT
SLAVE
MIN
MAX
2 – 3P
ns
5 + 6P
ns
PRODUCT PREVIEW
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 48)
NO.
C6203B-250
C6203B-300
C6203C-300
MASTER§
SLAVE
PARAMETER
2
th(CKXL-FXL)
td(FXL-CKXH)
Hold time, FSX low after CLKX low¶
Delay time, FSX low to CLKX high#
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
6
tdis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX low
7
tdis(FXH-DXHZ)
Disable time, DX high impedance following last data bit from FSX
high
1
MIN
UNIT
MIN
MAX
T–2
T+3
ns
L–2
L+3
ns
–3
4
L–2
L+3
3P + 4
MAX
5P + 17
ns
ns
P+3
3P + 17
ns
8
td(FXL-DXV)
Delay time, FSX low to DX valid
2P + 2 4P + 17
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
76
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
Bit 0
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 48. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
PRODUCT PREVIEW
DR
(n-2)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
77
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 49)
C6203B-250
C6203B-300
C6203C-300
NO.
MASTER
MIN
4
tsu(DRV-CKXH)
th(CKXH-DRV)
Setup time, DR valid before CLKX high
MAX
12
5
Hold time, DR valid after CLKX high
4
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
UNIT
SLAVE
MIN
MAX
2 – 3P
ns
5 + 6P
ns
PRODUCT PREVIEW
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 49)
NO.
C6203B-250
C6203B-300
C6203C-300
MASTER§
SLAVE
PARAMETER
MIN
2
th(CKXL-FXL)
td(FXL-CKXH)
Hold time, FSX low after CLKX low¶
Delay time, FSX low to CLKX high#
3
td(CKXL-DXV)
tdis(CKXL-DXHZ)
1
6
MAX
MIN
UNIT
MAX
L–2
L+3
ns
T–2
T+3
ns
Delay time, CLKX low to DX valid
–2
4
3P + 4
5P + 17
ns
Disable time, DX high impedance following last data bit from
CLKX low
–2
4
3P + 3
5P + 17
ns
7
td(FXL-DXV)
Delay time, FSX low to DX valid
H–2 H+4
2P + 2 4P + 17
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
78
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
6
Bit 0
7
FSX
DX
3
Bit(n-1)
4
Bit 0
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 49. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
PRODUCT PREVIEW
DR
(n-2)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
79
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 50)
C6203B-250
C6203B-300
C6203C-300
NO.
MASTER
MIN
4
tsu(DRV-CKXH)
th(CKXH-DRV)
Setup time, DR valid before CLKX high
MAX
12
5
Hold time, DR valid after CLKX high
4
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
UNIT
SLAVE
MIN
MAX
2 – 3P
ns
5 + 6P
ns
PRODUCT PREVIEW
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 50)
NO.
C6203B-250
C6203B-300
C6203C-300
MASTER§
SLAVE
PARAMETER
MIN
2
th(CKXH-FXL)
td(FXL-CKXL)
Hold time, FSX low after CLKX high¶
Delay time, FSX low to CLKX low#
3
td(CKXL-DXV)
Delay time, CLKX low to DX valid
6
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
7
tdis(FXH-DXHZ)
Disable time, DX high impedance following last data bit from
FSX high
1
MAX
MIN
UNIT
MAX
T–2
T+3
ns
H–2
H+3
ns
–3
4
H–2
H+3
3P + 4
5P + 17
ns
ns
P+3
3P + 17
ns
8
td(FXL-DXV)
Delay time, FSX low to DX valid
2P + 2 4P + 17
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
80
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
Bit 0
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 50. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
PRODUCT PREVIEW
DR
(n-2)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
81
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 51)
C6203B-250
C6203B-300
C6203C-300
NO.
MASTER
MIN
4
tsu(DRV-CKXL)
th(CKXL-DRV)
Setup time, DR valid before CLKX low
MAX
12
5
Hold time, DR valid after CLKX low
4
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
UNIT
SLAVE
MIN
MAX
2 – 3P
ns
5 + 6P
ns
PRODUCT PREVIEW
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 51)
NO.
C6203B-250
C6203B-300
C6203C-300
MASTER§
SLAVE
PARAMETER
MIN
UNIT
MIN
MAX
MAX
H–2
H+3
ns
T–2
T+2
ns
2
th(CKXH-FXL)
td(FXL-CKXL)
Hold time, FSX low after CLKX high¶
Delay time, FSX low to CLKX low#
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
–3
4
3P + 4
5P + 17
ns
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
–2
4
3P + 3
5P + 17
ns
1
6
7
td(FXL-DXV)
Delay time, FSX low to DX valid
L–2
L+5
2P + 2 4P + 17
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
82
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
3
Bit 0
Bit(n-1)
4
Bit 0
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 51. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
PRODUCT PREVIEW
DR
(n-2)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
83
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
DMAC, TIMER, POWER-DOWN TIMING
switching characteristics over recommended operating conditions for DMAC outputs†
(see Figure 52)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
1
tw(DMACH) Pulse duration, DMAC high
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
UNIT
MAX
2P – 3
ns
1
DMAC[3:0]
Figure 52. DMAC Timing
PRODUCT PREVIEW
timing requirements for timer inputs† (see Figure 53)
C6203B-250
C6203B-300
C6203C-300
NO.
MIN
1
2
tw(TINPH)
tw(TINPL)
UNIT
MAX
Pulse duration, TINP high
2P
ns
Pulse duration, TINP low
2P
ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
switching characteristics over recommended operating conditions for timer outputs†
(see Figure 53)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
3
tw(TOUTH)
tw(TOUTL)
Pulse duration, TOUT high
4
Pulse duration, TOUT low
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
2
1
TINPx
4
3
TOUTx
Figure 53. Timer Timing
84
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
UNIT
MAX
2P – 3
ns
2P – 3
ns
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
DMAC, TIMER, POWER-DOWN TIMING (CONTINUED)
switching characteristics over recommended operating conditions for power-down outputs†
(see Figure 54)
NO.
C6203B-250
C6203B-300
C6203C-300
PARAMETER
MIN
1
tw(PDH)
Pulse duration, PD high
† P = 1/CPU clock frequency in ns. For example, when running parts at 300 MHz, use P = 3.3 ns.
2P
UNIT
MAX
ns
1
PD
PRODUCT PREVIEW
Figure 54. Power-Down Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
85
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
JTAG TEST-PORT TIMING
timing requirements for JTAG test port (see Figure 55)
C6203B-250
C6203B-300
C6203C-300
NO.
MIN
1
UNIT
MAX
Cycle time, TCK
35
ns
3
tc(TCK)
tsu(TDIV-TCKH)
Setup time, TDI/TMS/TRST valid before TCK high
11
ns
4
th(TCKH-TDIV)
Hold time, TDI/TMS/TRST valid after TCK high
9
ns
switching characteristics over recommended operating conditions for JTAG test port
(see Figure 55)
PRODUCT PREVIEW
NO.
2
C6203B-250
C6203B-300
C6203C-300
PARAMETER
td(TCKL-TDOV)
Delay time, TCK low to TDO valid
MIN
MAX
–4.5
13.5
1
TCK
2
2
TDO
4
3
TDI/TMS/TRST
Figure 55. JTAG Test-Port Timing
86
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
UNIT
ns
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MECHANICAL DATA
GNZ (S–PBGA–N352)
PLASTIC BALL GRID ARRAY
27,20
SQ
26,80
25,00 TYP
1,00
25,20
SQ
24,80
0,50
0,50
PRODUCT PREVIEW
1,00
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
3
1
2
5
4
7
6
9
8
11 13 15 17 19 21 23 25
10 12 14 16 18 20 22 24 26
2,80 MAX
0,50 NOM
Seating Plane
0,70
0,50
0,10 M
0,60
0,40
0,15
4202595/A 03/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Flip chip application only.
Substrate color may vary.
thermal resistance characteristics (S-PBGA package) [C6203C only]
°C/W
NO
1
Air Flow m/s†
RΘJC
RΘJA
Junction-to-case
6.35
N/A
Junction-to-free air
20.0
0.00
RΘJA
RΘJA
Junction-to-free air
17.0
0.50
Junction-to-free air
16.3
1.00
RΘJA
Junction-to-free air
† m/s = meters per second
15.2
2.00
2
3
4
5
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
87
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MECHANICAL DATA
GLS (S-PBGA-N384)
PLASTIC BALL GRID ARRAY
18,10
SQ
17,90
16,80 TYP
0,80
0,40
AB
AA
Y
W
V
0,80
U
T
R
P
N
M
L
K
0,40
J
H
PRODUCT PREVIEW
G
F
E
D
C
B
A
1
3
2
5
4
7
6
9
8
11 13 15 17 19 21
10 12 14 16 18 20 22
Heat Slug
2,80 MAX
1,00 NOM
Seating Plane
0,55
0,45
0,10 M
0,45
0,35
0,12
4188959/C 04/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Thermally enhanced plastic package with heat slug (HSL)
Flip chip application only
thermal resistance characteristics (S-PBGA package) [C6203B only]
NO
1
°C/W
Air Flow m/s†
RΘJC
RΘJA
Junction-to-case
0.85
N/A
Junction-to-free air
21.6
0.0
RΘJA
RΘJA
Junction-to-free air
18.0
0.5
Junction-to-free air
15.5
1.0
RΘJA
Junction-to-free air
† m/s = meters per second
12.8
2.0
2
3
4
5
88
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
TMS320C6203B, TMS320C6203C
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS086F – JANUARY 1999 – REVISED SEPTEMBER 2001
MECHANICAL DATA
GNY (S-PBGA-N384)
PLASTIC BALL GRID ARRAY
18,10
SQ
17,90
16,80 TYP
0,80
0,40
AB
AA
Y
W
V
0,80
U
T
R
P
N
M
L
K
G
PRODUCT PREVIEW
0,40
J
H
F
E
D
C
B
A
1
3
2
5
4
7
9
6
8
11 13 15 17 19 21
10 12 14 16 18 20 22
2,35 MAX
Seating Plane
0,55
0,45
NOTES: A.
B.
C.
D.
∅ 0,10 M
0,45
0,35
0,12
4201137/B 02/01
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Flip chip application only
Substrate color may vary
thermal resistance characteristics (S-PBGA package) [C6203B/C6203C only]
NO
1
C6203B
(°C/W)
C6203C
(°C/W)
Air Flow m/s†
RΘJC
RΘJA
Junction-to-case
6.27
10.43
N/A
Junction-to-free air
17.6
21.8
0.0
RΘJA
RΘJA
Junction-to-free air
13.9
18.8
0.5
Junction-to-free air
13.1
17.7
1.0
5
RΘJA
Junction-to-free air
† m/s = meters per second
11.9
16.2
2.0
2
3
4
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
89
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2001, Texas Instruments Incorporated