WF512K32-XXX5 White Electronic Designs 512Kx32 5V FLASH MODULE, SMD 5962-94612 FEATURES n Organized as 512Kx32 n Access Times of 60, 70, 90, 120, 150ns n Commercial, Industrial and Military Temperature Ranges n Packaging n 5 Volt Programming. 5V ± 10% Supply. • 66 pin, PGA Type, 1.075" square, Hermetic Ceramic HIP (Package 400). n Low Power CMOS, 6.5mA Standby • 68 lead, 40mm, Low Profile 3.5mm (0.140"), CQFP (Package 502)1 n TTL Compatible Inputs and CMOS Outputs • 68 lead, 23.9mm (0.940") Low Profile CQFP (G1U) 3.5mm (0.140") high, (Package 519) n Page Program Operation and Internal Program n Embedded Erase and Program Algorithms n Built-in Decoupling Caps for Low Noise Operation Control Time • 68 lead, 22.4mm (0.880") Low Profile CQFP (G2U) 3.5mm (0.140") high, (Package 510)1 n n 100,000 Erase/Program Cycles Minimum n Sector Architecture n 8 equal size sectors of 64KBytes each n Any combination of sectors can be concurrently Note 1: Package Not Recommended for New Design Note 2: See Flash Programming Application Note 4M5 for algorithms. erased. Also supports full chip erase FIG. 1 P C IN ONFIGUR ATION T F OR OP Weight • WF512K32N - XH1X5 - 13 grams typical • WF512K32 - XG4TX51 - 20 grams typical • WF512K32 - XG1UX5 - 5 grams typical • WF512K32 - XG2UX5 1 - 8 grams typical WF512K32N-XH1X5 V P IEW IN D ESCRIPTION I/O0-31 Data Inputs/Outputs A0-18 Address Inputs WE1-4 Write Enables CS1-4 Chip Selects OE Output Enable VCC Power Supply GND Ground NC Not Connected B W E1 CS1 LOCK D W E2 CS2 IAGRAM W E3 CS3 W E4 CS4 OE A0-18 512K x 8 8 I/O0-7 March 2002 Rev. 6 1 512K x 8 8 I/O8-15 512K x 8 8 I/O16-23 512K x 8 8 I/O24-31 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF512K32-XXX5 White Electronic Designs FIG. 2 P C ONFIGURATION T OP F WF512K32-XG4TX51 V OR P IEW 9 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 GND I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 IN D ESCRIPTION I/O0-31 Data Inputs/Outputs NC A0 A1 A2 A3 A4 A5 CS1 GND CS3 WE A6 A7 A8 A9 A10 VCC IN 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 I/O16 I/O17 I/O18 I/O19 I/O20 I/O21 I/O22 I/O23 GND I/O24 I/O25 I/O26 I/O27 I/O28 I/O29 I/O30 I/O31 A0-18 Address Inputs WE Write Enable CS1-4 Chip Selects OE Output Enable VCC Power Supply GND Ground NC Not Connected B D LOCK IAGR AM CS 3 CS 2 CS 1 CS 4 WE OE A0-18 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 512K x 8 512K x 8 512K x 8 VCC A11 A12 A13 A14 A15 A16 CS2 OE CS4 A17 A18 NC NC NC NC NC 512K x 8 IN ONFIGUR ATION OP V OR WF512K32-XG2UX51 A ND IEW P 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 IN D ESCRIPTION I/O16 I/O17 I/O18 I/O19 I/O20 I/O21 I/O22 I/O23 GND I/O24 I/O25 I/O26 I/O27 I/O28 I/O29 I/O30 I/O31 A0-18 Address Inputs WE1-4 Write Enables CS1-4 Chip Selects OE Output Enable VCC Power Supply GND Ground B WE 1 CS 1 LOCK D IAGRAM WE 2 CS 2 WE 3 CS 3 WE 4 CS 4 OE A0-18 512K x 8 512K x 8 512K x 8 512K x 8 NC NC A18 WE4 OE CS2 A17 WE2 WE3 A16 CS1 A15 A14 A13 A12 A11 VCC 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 I/O24-31 I/O0-31 Data Inputs/Outputs 9 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 GND I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 8 WF512K32-XG1UX5 NC A0 A1 A2 A3 A4 A5 CS3 GND CS4 WE1 A6 A7 A8 A9 A10 VCC T F I/O16-23 I/O8-15 I/O0-7 FIG. 3 P C 8 8 8 8 I/O0-7 8 I/O8-15 8 I/O16-23 8 I/O24-31 Note 1: Package Not Recommended for New Design White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 2 WF512K32-XXX5 White Electronic Designs A BS O LUTE M AXIMUM R AT I N G S (1) C (TA = +25°C) APACITANCE Parameter Unit Operating Temperature -55 to +125 °C Supply Voltage Range (VCC) -2.0 to +7.0 V OE capacitance COE VIN = 0 V, f = 1.0 MHz Signal voltage range (any pin except A9) (2) -2.0 to +7.0 V CWE VIN = 0 V, f = 1.0 MHz Storage Temperature Range -65 to +150 °C Lead Temperature (soldering, 10 seconds) +300 °C Data Retention (Mil Temp) 20 years WE1-4 capacitance HIP (PGA) CQFP G4T CQFP G2U/G1U Endurance - write/erase cycles (Mil Temp) 100,000 cycles min. A9 Voltage for sector protect (VID ) (3) -2.0 to +14.0 Symbol Parameter V NOTES: 1. Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs may overshoot Vss to -2.0 V for periods of up to 20ns. Maximum DC voltage on output and I/O pins is Vcc + 0.5V. During voltage transitions, outputs may overshoot to Vcc + 2.0 V for periods of up to 20ns. 3. Minimum DC input voltage on A9 pin is -0.5V. During voltage transitions, A9 may overshoot Vss to -2V for periods of up to 20ns. Maximum DC input voltage on A9 is +13.5V which may overshoot to 14.0 V for periods up to 20ns. Conditions Max Unit 50 pF pF 20 50 15 CS 1-4 capacitance CCS VIN = 0 V, f = 1.0 MHz 20 pF Data I/O capacitance CI/O VI/O = 0 V, f = 1.0 MHz 20 pF Address input capacitance C AD VIN = 0 V, f = 1.0 MHz 50 pF This parameter is guaranteed by design but not tested. L OW Parameter C CQFP (TA = +25°C) A PACITA N C E Symbol Conditions Max Unit COE CWE CCS CI/O CAD VIN = 0 V, f = 1.0 MHz VIN = 0 V, f = 1.0 MHz VIN = 0 V, f = 1.0 MHz VI/O = 0 V, f = 1.0 MHz VIN = 0 V, f = 1.0 MHz 32 32 15 15 32 pF pF pF pF pF OE capacitance CQFP G4 capacitance CS1-4 capacitance Data I/O capacitance Address input capacitance This parameter is guaranteed by design but not tested. R ECOMMENDED Parameter O P E RAT I N G C ONDITIONS Symbol Min Max Unit Supply Voltage V CC 4.5 5.5 V Input High Voltage VIH 2.0 V CC + 0.5 V Input Low Voltage V IL -0.5 +0.8 V Operating Temp. (Mil.) TA -55 +125 °C Operating Temp. (Ind.) TA -40 +85 °C A9 Voltage for Sector Protect VID 11.5 12.5 V DC C - CMOS C (VCC = 5.0V, VSS = 0V, TA = -55°C to +125°C) HAR ACTERISTICS Parameter Max Unit I LI V CC = 5.5, V IN = GND or VCC 10 µA ILOx32 V CC = 5.5, V IN = GND or VCC 10 µA I CC1 CS = VIL, OE = VIH, f = 5MHz 190 mA VCC Active Current for Program or Erase (2) I CC2 CS = VIL, OE = VIH 240 mA VCC Standby Current ICC4 V CC = 5.5, CS = VIH, f = 5MHz 6.5 mA V CC Static Current ICC3 V CC = 5.5, CS = VIH 0.6 mA Output Low Voltage V OL I OL = 8.0 mA, V CC = 4.5 Output High Voltage V OH1 I OH = 2.5 mA, V CC = 4.5 Low V CC Lock-Out Voltage V LKO Input Leakage Current Output Leakage Current VCC Active Current for Read (1) Symbol OMPATIBLE Conditions Min 0.45 0.85 X 3.2 V CC V V 4.2 V DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V NOTES: 1. The ICC current listed includes both the DC operating current and the frequency dependent component (at 5 MHz). The frequency component typically is less than2 mA/MHz, with OE at VIH. 2. ICC active while Embedded Algorithm (program or erase) is in progress. 3 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF512K32-XXX5 White Electronic Designs AC CHARACTERISTICS WRITE/ERASE/PROGRAM OPERATIONS,CS CONTROLLED (VCC = 5.0V, VSS = 0V, TA = -55°C to +125°C) Parameter Symbol -60 Min -70 Max Min -90 Max Min -120 Max Min -150 Max Min Unit Max Write Cycle Time t AVAV t WC 60 70 90 120 150 ns Write Enable Setup Time tWLEL tWS 0 0 0 0 0 ns Chip Select Pulse Width t ELEH t CP 40 45 45 50 50 ns Address Setup Time t AVEL t AS 0 0 0 0 0 ns Data Setup Time tDVEH tDS 40 45 45 50 50 ns Data Hold Time t EHDX tDH 0 0 0 0 0 ns Address Hold Time tELAX t AH 40 45 45 50 50 ns Chip Select Pulse Width High t EHEL t CPH 20 20 20 20 20 ns Duration of Byte Programming Operation (1) t WHWH1 300 300 300 300 300 µs Sector Erase Time (2) t WHWH2 15 15 15 15 15 sec Read Recovery Time t GHEL 0 Chip Programming Time Chip Erase Time (3) NOTES: 1. Typical value for tWHWH1 is 7µs. 2. Typical value for tWHWH2 is 1sec. 3. Typical value for Chip Erase Time is 8sec. F . 4 AC T IG EST C 0 0 0 0 ns 11 11 11 11 11 sec 64 64 64 64 64 sec AC T IRCUIT EST C ONDITIONS Parameter Typ Unit Input Pulse Levels VIL = 0, VIH = 3.0 V Input Rise and Fall 5 ns 1.5 V Input and Output Reference Level Output Timing Reference Level 1.5 V Notes: VZ is programmable from -2V to +7V. IOL & IOH programmable from 0 to 16mA. Tester Impedance Z0 = 75W. VZ is typically the midpoint of VOH and VOL. IOL & IOH are adjusted to simulate a typical resistive load circuit. ATE tester includes jig capacitance. White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 4 WF512K32-XXX5 White Electronic Designs AC C W /E /P O , WE C (VCC = 5.0V, TA = -55°C +125°C) HARACTERISTICS RITE R A SE ROGR AM PERATIONS ONTROLLED TO Parameter Symbol -60 Min -70 Max Min -90 Max Min -120 Max Min -150 Max Min Unit Max WF512K32-XXX5 150 ns Write Cycle Time t AVAV t WC 60 70 90 Chip Select Setup Time tELWL tCS 0 0 0 0 0 ns Write Enable Pulse Width t WLWH t WP 40 45 45 50 50 ns Address Setup Time t AVWH t AS 0 0 0 0 0 ns Data Setup Time t DVWH tDS 40 45 45 50 50 ns Data Hold Time t WHDX tDH 0 0 0 0 0 ns Address Hold Time tWHAX t AH 40 45 45 50 50 ns Write Enable Pulse Width High t WHWL t WPH 20 Duration of Byte Programming Operation (1) t WHWH1 Sector Erase Time (2) t WHWH2 Read Recovery Time before Write t GHWL 20 120 20 300 20 300 15 20 300 15 300 15 ns 300 µs 15 sec 15 0 0 0 0 0 ns tVCS 50 50 50 50 50 µs Output Enable Setup Time tOES 0 Output Enable Hold Time (4) tOEH 10 VCC Set-up Time Chip Programming Time 11 11 0 10 Chip Erase Time (3) 11 0 10 64 11 0 10 64 11 0 ns 10 64 sec 64 ns 64 sec NOTES: 1. Typical value for tWHWH1 is 7µs. 2. Typical value for tWHWH2 is 1sec. 3. Typical value for Chip Erase Time is 8sec. 4. For Toggle and Data Polling. AC C R O (VCC = 5.0V, TA = -55°C HAR ACTERISTIC S Parameter Symbol EAD NLY -60 Min TO O +125°C) PER ATIONS -70 Max Read Cycle Time t AVAV t RC Address Access Time t AVQV t ACC 60 60 Chip Select Access Time t ELQV t CE 60 Output Enable to Output Valid t GLQV tOE 30 Chip Select to Output High Z (1) t EHQZ t DF 20 Output Enable High to Output High Z (1) t GHQZ t DF 20 Output Hold from Address, CS or OE Change, whichever is First 1. Guaranteed by design, but not tested t AXQX tOH Min -90 Max 70 0 -120 Max 90 70 0 5 Min Min Max 120 -150 Min Unit Max 150 ns 90 120 150 ns 70 90 120 150 ns 35 35 50 55 ns 20 20 30 35 ns 20 20 30 35 ns 0 0 0 ns White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com White Electronic Designs FIG. 5 AC W AVEFORMS F OR R EAD O P E R ATIONS White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 6 WF512K32-XXX5 White Electronic Designs F .6 W IG RITE /E R ASE /P ROGRAM O PERATION , WE C WF512K32-XXX5 ONTROLLED NOTES: 1. PA is the address of the memory location to be programmed. 2. PD is the data to be programmed at byte address. 3. D7 is the output of the complement of the data written to the device (for each chip). 4. DOUT is the output of the data written to the device. 5. Figure indicates last two bus cycles of four bus cycle sequence. 7 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF512K32-XXX5 White Electronic Designs F . 7 AC W AVEFORMS C HIP /S ECTOR E RASE O PER ATIONS AAH tDS tDH White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 8 VCC tVCS NOTE: 1. SA is the sector address for Sector Erase. Data WE OE CS Addresses tGHWL tCS tWP tWPH 55H 2AAAH tAS 5555H tAH 5555H 80H 5555H AAH 2AAAH 55H SA 10H/30H IG WF512K32-XXX5 White Electronic Designs F . 8 AC W IG AVEFORMS F OR D ATA P OLLING D URING E MBEDDED A LGORITHM O PER ATIONS CS OE WE Data D7 D0-D6 t CH tOEH tCE t OE tWHWH 1 or 2 D7 D0-D6 = Invalid t DF t OH D0-D7 Valid Data D7 = Valid Data t OE High Z 9 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com White Electronic Designs F .9 A IG LTERNATE CS C ONTROLLED P ROGR AMMING O PER ATION T IMINGS Notes: 1. PA represents the address of the memory location to be programmed. 2. PD represents the data to be programmed at byte address. 3. D7 is the output of the complement of the data written to the device (for each chip). 4. DOUT is the output of the data written to the device. 5. Figure indicates the last two bus cycles of a four bus cycle sequence. White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 10 WF512K32-XXX5 WF512K32-XXX5 White Electronic Designs P AC K AG E 400: 66 P , PGA T IN YPE ,C E R AMIC H -I -L EX N INE P AC K AG E , H (H1) IP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES 11 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com White Electronic Designs P AC K AG E 510: 68 L EAD ,C E R AMIC Q UAD F L AT P AC K WF512K32-XXX5 , CQFP (G2U)1 The White 68 lead G2U CQFP fills the same fit and function as the JEDEC 68 lead CQFJ or 68 PLCC. But the G2U has the TCE and lead inspection advantage of the CQFP form. 0.940" ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES Note 1: Package Not Recommended for New Design White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 12 WF512K32-XXX5 White Electronic Designs P AC K AG E 519: 68 L EAD ,C E R AMIC Q UAD F L AT P AC K ,L P OW CQFP (G1U) ROFILE The White 68 lead G1U CQFP fills the same fit and function as the JEDEC 68 lead CQFJ or 68 PLCC. But the G1U has the TCE and lead inspection advantage of the CQFP form. ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES P AC K AG E 502: 68 L EAD ,C E R AMIC Q UAD F L AT P AC K ,L OW P ROFILE CQFP (G4T) 1 5.1 (0.200) MAX 39.6 (1.56) ± 0.38 (0.015) SQ 1.27 (0.050) ± 0.1 (0.005) PIN 1 IDENTIFIER Pin 1 12.7 (0.500) ± 0.5 (0.020) 4 PLACES 5.1 (0.200) ± 0.25 (0.010) 4 PLACES 1.27 (0.050) TYP 0.38 (0.015) ± 0.08 (0.003) 68 PLACES 0.25 (0.010) ± 0.05 (0.002) 38 (1.50) TYP 4 PLACES ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES Note 1: Package Not Recommended for New Design 13 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF512K32-XXX5 White Electronic Designs O RDERING I NFORMATION W F 512K32 X - XXX X X 5 X LEAD FINISH: Blank = Gold plated leads A = Solder dip leads PP PROGRAMMING VOLTAGE V 5=5V DEVICE GRADE: Q = MIL-STD-883 Compliant M = Military Screened I = Industrial C = Commercial -55°C to +125°C -40°C to +85°C 0°C to +70°C PACKAGE TYPE: H1 = 1.075" sq. Ceramic Hex In Line Package, HIP (Package 400*) G2U1 = 22.4mm Ceramic Quad Flat Pack, Low Profile CQFP (Package 510) G4T1 = 40mm Low Profile CQFP (Package 502) G1U = 23.9mm Ceramic Quad Flat Pack, Low Profile CQFP (Package 519) ACCESS TIME (ns) IMPROVEMENT MARK N = No Connect at pins 21 and 39 in HIP for Upgrade ORGANIZATION, 512K x 32 User configurable as 1M x 16 or 2M x 8 FLASH WHITE ELECTRONIC DESIGNS CORP. Note 1: Package Not Recommended for New Design White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 14 White Electronic Designs DEVICE TYPE SPEED WF512K32-XXX5 PACKAGE SMD NO. 512K x 32 Flash Module 150ns 66 pin HIP (H1) 1.075" sq. 5962-94612 01H4X 512K x 32 Flash Module 120ns 66 pin HIP (H1) 1.075" sq. 5962-94612 02H4X 512K x 32 Flash Module 90ns 66 pin HIP (H1) 1.075" sq. 5962-94612 03H4X 512K x 32 Flash Module 70ns 66 pin HIP (H1) 1.075" sq. 5962-94612 04H4X 512K x 32 Flash Module 60ns 66 pin HIP (H1) 1.075" sq. 5962-94612 05H4X 512K x 32 Flash Module 150ns 68 lead CQFP Low Profile (G4T) 5962-94612 01HTX 512K x 32 Flash Module 120ns 68 lead CQFP Low Profile (G4T) 5962-94612 02HTX 512K x 32 Flash Module 90ns 68 lead CQFP Low Profile (G4T) 5962-94612 03HTX 512K x 32 Flash Module 70ns 68 lead CQFP Low Profile (G4T) 5962-94612 04HTX 512K x 32 Flash Module 60ns 68 lead CQFP Low Profile (G4T) 5962-94612 05HTX 512K x 32 Flash Module 150ns 68 lead CQFP/J (G2U) 5962-94612 01HZX 512K x 32 Flash Module 120ns 68 lead CQFP/J (G2U) 5962-94612 02HZX 512K x 32 Flash Module 90ns 68 lead CQFP/J (G2U) 5962-94612 03HZX 512K x 32 Flash Module 70ns 68 lead CQFP/J (G2U) 5962-94612 04HZX 512K x 32 Flash Module 60ns 68 lead CQFP/J (G2U) 5962-94612 05HZX 512K x 32 Flash Module 150ns 68 lead CQFP (G1U) 5962-94612 01H9X 512K x 32 Flash Module 120ns 68 lead CQFP (G1U) 5962-94612 02H9X 512K x 32 Flash Module 90ns 68 lead CQFP (G1U) 5962-94612 03H9X 512K x 32 Flash Module 70ns 68 lead CQFP (G1U) 5962-94612 04H9X 512K x 32 Flash Module 60ns 68 lead CQFP (G1U) 5962-94612 05H9X 15 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com