® ® Table of contents General Production Program.......................................................................................................page 2 Main Characteristics and Types .............................................................................................................2 LEMO’s Push-Pull Self-Latching System...............................................................................................3 Mechanical Connecting Characteristics ................................................................................................3 Series and Types......................................................................................................................................4 General Characteristics...................... Outer Shell, Technical Characteristics .......................................................................................................5 Insulator, Technical Characteristics ...........................................................................................................6 Contact, Technical Characteristics.............................................................................................................6 Cable Fixing ...............................................................................................................................................8 Clamping Type ...........................................................................................................................................8 Series 00 .................................................... Introduction ................................................................................................................................................9 Interconnections .........................................................................................................................................9 Model Description ....................................................................................................................................10 Part Section Showing Internal Components ..................................................................................................10 Mechanical, Environmental and Electrical Characteristics .........................................................................10 Recommended Cables.............................................................................................................................11 Anodized Color of Aluminum Alloy Connectors .......................................................................................11 Part Number Example ..............................................................................................................................12 Models: Plugs...........................................................................................................................................13 Fixed Receptacle .....................................................................................................................................16 Free Receptacle .......................................................................................................................................19 Plugs with Resistors .................................................................................................................................20 Couplers ...................................................................................................................................................21 Plugs with Receptacle ..............................................................................................................................21 Watertight Fixed Receptacles ..................................................................................................................22 Adaptors ...................................................................................................................................................23 Assembled Cables ...................................................................................................................................27 Accessories.............................................. Plug Cap ..................................................................................................................................................27 Blanking Cap for Fixed Receptacle ..........................................................................................................28 Blanking Cap for Free Receptacle ...........................................................................................................28 Earthing Cap ............................................................................................................................................28 Crimp Ferrule ...........................................................................................................................................29 Strain Relief..............................................................................................................................................29 Insulating Washers...................................................................................................................................29 Locking Washers......................................................................................................................................29 Tapered Washers.....................................................................................................................................30 Hexagonal Nut .........................................................................................................................................30 Round Nut ................................................................................................................................................30 Conical Nut...............................................................................................................................................30 Earthing Washer ......................................................................................................................................30 Tooling ........................................................ Spanner for nuts.......................................................................................................................................31 Spanner for plugs .....................................................................................................................................31 Collet nut wrench .....................................................................................................................................32 Extraction Tool for plugs ..........................................................................................................................32 Crimping Tool ...........................................................................................................................................32 Panel Cut-Out ..........................................................................................................................................33 Printed Circuit Board Drilling Pattern........................................................................................................33 Terminating instructions ...........................................................................................................................34 Recommended Coaxial Cables................................................................................................................38 Technical Tables ......................................................................................................................................38 1 ® ® General Production Program Connectors ● ● ● ● ● ● ● ● Adaptors ● ● Unipole from 2 to 150 Amps Coaxial 50 and 75 Ω Coaxial 50 Ω (NIM-CAMAC) Coaxial 50 Ω for frequency up to 12 GHz Coaxial 50 Ω SMA Multicoaxial 50 and 75 Ω Multipole from 2 to 106 contacts High Voltage 3, 5, 8, 10, 15, 30, and 50 kV dc Multi High Voltage 3, 5, and 10 kV dc Triaxial 50 and 75 Ω Quadrax Mixed: High Voltage (HV) + Low Voltage (LV) Mixed: Coax + LV Thermocouple Multithermocouple Fiber optic singlemode Fiber optic multimode Mixed: fiber optic + LV For OPTABALL® fiber optic singlemode Fluidic Multifluidic Mixed: fluidic + LV Subminiature Miniature Plastic Printed circuit board Remote handling Watertight Sealed (pressure and/or vacuum) With plastic outer shell With aluminum outer shell With stainless steel outer shell With special radiation resistant insulator material With screw thread coupling for very high pressure With microswitch Patch Panels For audio-mono applications: triax or 3 contacts (with or without switching) For audio-stereo applications: quadrax or 6 contacts For video applications: coax 75 Ω For video HDTV applications: 3 coax 75 Ω + 2LV For fiber optic applications Accessories Insulator for crimp contacts Crimp contacts Coaxial contacts Fiber optic contacts Fiber optic ferrules Caps Strain relief Insulating washers Double plastic panel washers Locking washers Tapered washers Hexagonal nuts Round nuts Conical nuts Earthing washers Lead-through with cable collet ● ● ● ● ● ● ● ● ● ● ● Tools ● ● On request ● For BNC, C, UHF, N, CINCH connectors For GEN-RADIO, SMA connectors For TNC connectors Spanners Crimping tools Positioners Crimping dies Extractors Fiber optic termination workstation Fiber optic polishing tools Filtered connectors Connectors with special alloy housing Mixed special connectors Assembly onto cable ● Connectors, accessories, and tools found in this catalog. Main Characteristics and Types Series STANDARD WATERTIGHT KEYED KEYED WATERTIGHT PLASTIC SCREW 01 (Minax) 00 (NIM-CAMAC) R0 0S to 6S 0A / 4A 1D / 2C 1Y-3Y-6Y 0E to 6E 3T 4M 00 (multipin) 0B to 5B 2G 0K to 5K 3P 03 EA 0V to 5V 2W Push-Pull Latching Key Stepped insert (Half-Moon) Contact 2 Key (G) or stepped insert (Half-Moon) Key (G) or key-way code Metal or plastic Shell Insert Screw Stepped insert (Half-Moon) Plastic Cylindrical Solder, Crimp or Print Metal Cylindrical or stepped insert (Half-Moon) Solder ® ® LEMO’s Push-Pull Self-Latching Connecting System This self-latching system is renowned worldwide for its easy and quick mating and unmating features. It provides absolute security against vibration, shock or pull on the cable, and facilitates operation in a very limited space. The LEMO self-latching system allows the connector to be mated by simply pushing the plug axially into the receptacle. Once firmly latched, connection cannot be broken by pulling on the cable or any other component part other than the outer release sleeve. When required, the connector is disengaged by a single axial pull on the outer release sleeve. This first disengages the latches and then withdraws the plug from the receptacle. Mechanical Connecting Characteristics Fv Fv: average latching force = 9 N Fd Fd: average unmating force with axial pull on the outer release sleeve = 7 N Fa Fa: average pull force with axial pull on the collet nut = 120 N Notes: the forces were measured on outer shells not fitted with contacts. The mechanical endurance represents the number of cycles after which the latching system is still effective (1 cycle = 1 latching/unlatching – 300 cycles per hour). Mechanical endurance: 5000 cycles. The values were measured according to MIL-STD-1344A method 2013.1. 1N = 0,102 kg. 3 ® ® Series and Types 01 00 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Thermocouple Mixed fluidic + LV Multifluidic Fluidic ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 2G ● 0K 1K 2K 3K 4K 5K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 3P ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● EA 4 Mixed FO + LV ● 00 0B 1B 2B 3B 4B 5B 2W Multi Fiber Optic ● ● ● 03 Screw Fiber Optic (single fiber) ● ● ● 3T 0V 1V 2V 3V 4V 5V Mixed Triax + LV Mixed Coax + LV ● ● ● ● 4M Plastic Mixed HV + LV ● ● 1Y 3Y 6Y Keyed Watertight Multi Coaxial ● ● 4A Keyed Multi High Voltage ● ● 2C Watertight Multi High Voltage (Keyed series) ● 1D 0E 1E 2E 3E 4E 5E 6E Quadrax Triaxial 75 Ω Triaxial 50 Ω High Voltage ● ● 0A Standard Multipole ● ● R0 0S 1S 2S 3S 4S 5S 6S Coaxial 75 Ω Unipole Series Coaxial 50 Ω Types ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ® ® General Characteristics Outer Shell Brass LEMO series 00 connectors have a brass outer shell as standard, and this is suitable for most general purpose applications, including civilian and military. The brass outer shells have a nickel-plated surface which ensures very good protection against most environments. Alternative protective coatings available are: – Nickel-chrome offering higher protection against salt air and most corrosive agents – Nickel-gold – Nickel-black chrome. After the black chrome treatment, the part is coated with a protective film. excellent resistance to corrosion. The shell surface is protected by anodizing which is available in six colors: blue, yellow, black, red, green, and natural. Plastic Materials A PEEK outer shell is available which offers excellent insulating properties and is mostly used in the medical industry. This material is suitable for gas or steam sterilization. Other Metallic Components In general, other components are manufactured from brass. However, bronze is used where good elasticity is required (for example: earthing crown). These parts are nickel or nickel-gold plated depending on the utilization. Aluminum Alloy Aluminum alloy outer shells find numerous applications where light weight is a predominant factor; such as in the aeronautics and space industries, and for portable and mobile equipment. These materials have high mechanical strength and Materials and Treatment Component Material (Standard) Brass (UNS C 38500) Outer shell, collet nut, Al. alloy (AA 6012) conical nut PEEK (MIL-P-46183) Earthing crown Cu-Be (UNS C 17300) Latch sleeve Special Brass Crimp ferrule Copper (UNS C 18700) Locking washer Bronze (UNS C 52100) Brass (UNS C 38500) Hexagonal nut Al. alloy (AA 6012) 1) Other metallic components Brass (UNS C 38500) Seals Silicone or FPM Nickel Cu Ni Surface Treatment (µm) Chrome Gold Cu Ni Cr Cu Ni Au 0.5 0.5 3 3 0.5 0.5 0.5 0.5 0.5 3 3 3 3 3 – – – – – – – – – – 0.5 3 – – 0.3 0.5 3 anodized beige colored – 0.5 3 – 0.5 3 – 0.5 3 – 0.5 3 – 0.5 3 anodized – 0.5 3 without treatment 0.5 Black Chrome Cu Ni Cr – 1 2 Notes: The surface treatment standards are as follows: – nickel QQ-N-290A, or MILC-26074C 1.5 1.5 1.5 0.5 0.5 – – – – – – – – – – – – – – – – chrome QQ-N-320B 0.5 – – – 1) – gold MIL-G-45204C type I, class 1 (1.5 µm) class 00 (0.5 µm) – black chrome MIL-C-14538C supplied only with aluminum alloy free or fixed receptacles. Electrical Characteristics Screen continuity: according to test MIL-STD-1344A, method 3007. Values with earthing crown and latch sleeve or inner-sleeve nickel R1 plated. R2 Values with gold-plated earthing crown and nickel plated latch sleeve or inner-sleeve. R3 Values with earthing crown and gold-plated latch sleeve or innersleeve. A mV G R1 (mΩ) R2 (mΩ) R3 (mΩ) 3.5 2.8 2.0 Testing current: 1A A = Ammeter mV = Millivoltmeter G = Generator 5 ® ® Insulator Technical Description LEMO uses virgin quality PTFE for the insulator material of coaxial connectors, which guarantees excellent insulating properties. LEMO also proposes PEEK (Polyether Etherketone). Its higher mechanical strength and excellent radiation resistance make it ideal for most applications. Technical Characteristics Test method Property Dielectric strength Volume resistivity at 50% HR and 23°C Surface resistivity Thermal conductivity Comparative tracking index Dielectric constant (106 Hz) Dissipation factor (106 Hz) Continuous service temperature Water absorption in 24h at 23°C Radiation resistance Flammability rating ASTM D 149 ASTM D 257 ASTM D 257 ASTM C 177 IEC 112 ASTM D 150 ASTM D 150 – ASTM D 570 – UL 94 Unit PEEK PTFE kV/mm 19 - 25 17.2 - 24 Ω cm 1016 1018 Ω 1015 1017 W/K m 0.25 0.23 V CTI 150 CTI 500 – 3.2 - 3.5 2 - 2.1 – < 0.005 < 0.0003 °C 250 260 % < 0.3 < 0.01 2 102 Gy 107 – V0 V0 ● ● ● Note: the technical data contained in this chapter gives general information about plastic materials used by LEMO as electrical insulator materials. LEMO reserves the right to propose new materials which would have better technical characteristics and to withdraw any material contained in this publication or others from LEMO and its subsidiary companies. LEMO only uses granulated, powdered plastic materials or bars from specialized suppliers. LEMO is not responsible, in any case, for these materials. Radiation resistance PEEK Damage minimal to mild (almost always usable) mild to moderate (often satisfactory) PTFE moderate to severe (unusable) 103 101 104 102 105 103 106 104 107 105 108 106 109 107 1010 rads 108 Gray (Gy) γ ray dose Electrical Contact Technical Description Contact Material The secure, reliable electromechanical connection achieved with LEMO female contacts is mainly due to two important design features: 1. Prod proof entry which ensures perfect concentric mating even with well woon and/or carelessly handled connectors. 2. The pressure spring that maintains a constant, even force on the male contact when mated. The leading edge of the spring is chamfered to slide smoothly on the male contact, preserving the gold-plated surface treatment and preventing undue wear. LEMO female electrical contacts are made from bronze (UNS C 54400). Bronze is chosen because of its high modulus of elasticity, its excellent electrical conductivity and high mechanical strength. LEMO male solder and print contacts are made from brass (UNS C 38500). Male crimp contacts are made from brass (UNS C 34500) which is ideal for crimping onto the electrical conductor of the cable. Conductor retention method Both male and female contacts are available in crimp, solder or print versions. 6 ® ® Materials and Treatments Type Au Ni Cu Bronze Material (Standard) Surface treatment (µm) Cu Ni Au Male solder Male crimp Male print Brass (UNS C 38500) Brass (UNS C 34500) Brass (UNS C 38500) 0.5 3 1.5 Female solder Female crimp Female print Bronze (UNS C 54400) 0.5 3 2.0 Notes: the standard surface treatments are as follows: – Nickel QQ-N-290A or MIL-C-26074C – Gold MIL-G-45204C, type I, class 1. Solder Contacts Features of the LEMO crimp contacts: The solder pot of these contacts is machined at an angle to form a cup into which the solder can flow. – Quick and simple assembly – Insulator is not heated during contact-to-conductor assembly – High temperature applications possible – Increased conductor retention force ø 0.7 ø 0.6 Print contacts ø 0.6 Print contacts are available in certain connectors versions, mostly for the straight or elbow receptacles models. Connection is made on flexible or rigid printed circuits by soldering ø 0.7 The LEMO crimp contacts are factory annealed to relieve internal stresses, and reduce the risk of the material work hardening during the crimping process. During this process, an induction heating machine designed by LEMO’s Research and Development Department is used (photo 2). ø 0.7 The square form crimp method is used (MIL-C-22520F, type 2) (photo 1). The crimp method requires a controlled compression to obtain a symmetrical deformation of the conductor strand and of the contact material. The inspection hole in the side of the contact verifies correct positioning of the conductor within the contact. A good crimping is characterized by a small conductor section reduction and by the quite closed free spaces. Contact Resistance in Relation to Number of Mating Cycles (Corrosion according to MIL-STD-202, method 101D). Contact resistance (mΩ) 1000 3000 5000 cycles cycles cycles 5.6 5.7 6.1 ø 0.7 Thickness comparison between the outside and the inside of female contacts male (µm) 1.5 1 ø 0.7 Crimp Contacts Gold thickness1) female outside (µm) inside (%) 2 60 Note: 1) minimal thickness according to MIL-G-45204C, type I, class 1. A = test point 2 2.5 2.5 A A 7 ® ® Cable Fixing Cable fixing onto LEMO connectors is determined by the connector model. This is achieved either with a cable collet system or with hexagonal crimping (MIL-C-22520F, type 2). The collet system cable fixing is made without any special tooling. The crimping method guarantees a good electrical continuity of the shield which improves greatly the shielding efficiency of the cable/connector link. Material and Treatment Component Earthing sleeve Collet Crimp ferrule Collet nut Material (Standard) Brass (UNS C 38500) Brass (UNS C 38500) Copper (UNS C 18700) Brass (UNS C 38500) Surface Treatment (µm) Cu Ni 0.5 0.5 0.5 0.5 3 3 3 3 Note: collet nut tightening torque: maximum 0.25 Nm (1N = 0.102 kg) Type C Cable Clamping This system has an earthing sleeve ➂ and a collet ➀ which is compressed by the collet nut ➁ to ensure a good clamp onto the cable. When assembling the connector, the cable shield is gripped between the earthing sleeve and the collet. 3 2 Straight plug 1 Free receptacle 3 2 Fixed receptacle nut fixing Type E Crimping The back end of the crimp nut ➃ which receives the shield braid, is milled to ensure good conductivity once crimped. 4 Straight plug 1 Free receptacle Fixed receptacle nut fixing 8 4 ® ® Series 00 (NIM-CAMAC-CD/N 549) Introduction The 00 series is a range of 50 Ω coaxial connectors. They are suitable for a wide variety of applications particularly in measurement, control system and nuclear physics, having formed the basis for the NIM-CAMAC-CD/N 549 standard. LEMO 00 connectors offer customers many benefits including: – Self-latching push-pull system – Aesthetically pleasing appearance – Small size – High packing density – Rugged construction – Ease of use – Low weight – Reliable performances – Wide choice to suit application Interconnections Straight and elbow plugs Straight and elbow receptacles Straight receptacles FFE FFA ERA, ERE EPE FLA FFC ERN FLS, FLV FFA ERC FAA FFA ERT FAB FFS, FFV ERM Straight couplers PCA RAD EPL, EPM, EPK PCS RMA EPS PSA Straight and elbow plugs with receptacle EPN FTR PSS FTA PES EPY Plugs with resistance FFY FPA FTL ECP FRT FPL FFF EPA, EPB, EPC FLR FTY Watertight or vacuumtight models Straight receptacles HGP HGW Straight coupler EWF EWV SWH 9 ® ® Models Description ABA Adapter from LEMO receptacle to BNC plug ABB Adapter from LEMO fixed receptacle to BNC receptacle ABC Adapter from LEMO receptacle to BNC receptacle ABD Adapter from LEMO receptacle to BNC fixed receptacle ABF Adapter from LEMO plug to BNC receptacle ACA Adapter from LEMO receptacle to C plug ACB Adapter from LEMO receptacle to C receptacle AGG Adapter from LEMO receptacle to General-Radio receptacle type 874 AGH Adapter from LEMO receptacle to UHF plug ANA Adapter from LEMO receptacle to N plug ANB Adapter from LEMO receptacle to N receptacle ANC Adapter from LEMO receptacle to N fixed receptacle APF Adapter from LEMO plug to CINCH receptacle ASA Adapter from LEMO receptacle to SMA plug ASB Adapter from LEMO receptacle to SMA receptacle ASF Adapter from LEMO plug to SMA receptacle ASG Adapter from LEMO plug to SMA plug ECP Straight receptacle with two nuts EPA Straight receptacle for printed circuit EPB Straight receptacle for printed circuit (long studs) EPC Straight receptacle for printed circuit with clearance under the body EPE Straight receptacle with two nuts for printed circuit EPK Elbow receptacle (90°) for printed circuit with clearance under the body EPL Elbow receptacle (90°) for printed circuit EPM Elbow receptacle (90°) for printed circuit (long studs) EPN Straight receptacle for press mouniting in pair on printed circuit, EPS Elbow receptacle (90°) with two nuts for printed circuit EPY Elbow receptacle (90°) for printed circuit with two vertical receptacles ERA Fixed receptacle, nut fixing ERC Fixed receptacle, nut fixing, with slots in flange ERE Fixed receptacle, nut fixing, with conical lead in ERM Fixed receptacle, nut fixing, with microswitch ERN Fixed receptacle, nut fixing, with tags ERT Straight receptacle without thread, force or adhesive fit EWF Fixed receptacle, nut fixing, with tags, vacuumtight, (back panel mounting) EWV Fixed receptacle, vacuumtight FAA Straight plug, non-latching, nut fixing FAB FFA FFA FFA FFC FFE FFF FFS FFY FFV FLA FLR FLS FLV FPA FPL FRT FTA FTL FTR FTY HGP HGW PCA Straight plug, non-latching, riveted fixing Straight plug with cable collet Straight plug with cable collet PEEK outer shell Straight plug with cable collet and nut for fitting a strain relief Straight plug with flats on latch sleeve and cable collet Straight plug with front sealing ring, cable collet and nut for fitting a strain relief Straight plug, non-latching, with cable collet Straight plug with cable crimping Straight plug with cable collet Straight plug for cable crimping with improved screen efficiency Elbow plug (90°) with cable collet Elbow plug (90°) with resistor Elbow plug (90°) for cable crimping Elbow plug (90°) for cable crimping with improved screen efficiency Straight plug, non-latching, for printed circuit Elbow plug (90°) non-latching for printed circuit Straight plug with resistor or shorted T-plug with two receptacles in line T-plug with two receptacles (90°) Elbow plug (90°) with one receptacle Straight plug with two parallel receptacles Fixed receptacle, nut fixing, watertight Fixed receptacle, nut fixing, with rear sealing ring Free receptacle with cable collet Part Section Showing Internal Components 7 6 3 4 5 2 1 1 Fixed receptacle 1 outer shell 2 earthing crown 3 retaining ring 4 hexagonal nut 5 locking washer 6 insulator 7 female contact 7 6 5 4 8 Plug with cable clamping 1 outer shell 2 latch sleeve 3 collet nut 4 earthing sleeve 5 rear insulator 6 insulator 7 male contact 8 collet Models with collet nut for fitting a strain relief To order models with a collet nut for fitting a strain relief, add a “Z” in the “variant” position (see page12) of the part number. Strain reliefs are available in nine colors and several sizes to accomodate different cable outside diameters. They are ordered separately as indicated in the “Accessories” section. Watertight/Vacuumtight models The fixed receptacles and couplers, models HGP, HGW, EWF, EWV, SWH allow the device on which they are 10 2 3 1 6 5 4 2 3 7 Plug with cable crimping 1 outer shell 2 latch sleeve 3 crimp backnut 4 rear insulator 5 insulator 6 male contact 7 crimp ferrule fitted to reach a protection index of IP66 as per IEC 529 (unmated). They are fully compatible with the non watertight models of the same series and are widely used for portable radios, ship installations and in aircraft. Specially prepared & tested versions of these models are available for vacuumtight applications guaranteeing a leakage level of less than 10-6 mbar.l.s-1 (as per MIL-STD1344A standard method 1008). A vacuumtight model is identified by the letter at the end of the part number (certificate on request). To seal both the watertight and vacuumtight models, LEMO uses an epoxy resin. ® ® Technical Characteristics Mechanical and climatical Characteristics Electrical Value Standard Method Contact retention force Cable pull off force Connector pull off force > 18 N > 100 N > 90 N MIL-STD-1344A 2007.1 MIL-STD-1344A 2009.1 Endurance > 1000 cycles MIL-STD-1344A 2016 Operating temperature 1) - 55°C + 260°C Note: 1) to seal both the watertight and vacuumtight models, LEMO uses and epoxy resin. The operating temperature is -20°C and +80°C for sealed models. Characteristics Value Standard Method Impedance Operating voltage (50 Hz) Test voltage (50 Hz) Rated current Contact resistance Screen resistance Insulating resistance 50 Ω VSWR (f. in GHz) 75 Ω 50 Ω 0.7 kV AC 2.1 kV AC 4A < 6 mΩ < 3.5 mΩ > 1012 Ω 1.09+0.11f 1.08+0.51f IEC 130-1 1ère ed. MIL-STD-1344A IEC 512-3 MIL-STD-202 F MIL-STD-1344A MIL-STD-1344A IEC 169-1-1 IEC 169-1-1 § 14.5 3001.1 307 3007 3003.1 Voltage Standing Wave Ratio Screening efficiency (EMC properties) in dB (transfer impedance in dBohm) The VSWR (Voltage Standing Wave Ratio) is the value representing the power reflected in a connection. In most cases, the working frequency range is where VSWR ≤ 1.25 The screening efficiency is the ratio between the electromagnetic field inside the connector and a power source at the outside of the connector (or vice versa). T.O.S. 1.5 75 Ω (dBΩ) -10 (dB) 60 -20 80 -30 100 1.4 1.3 50 Ω 1.2 1.1 -40 0.01 0.1 1 10 100 1.0 0 500 1000 1500 f (MHz) Note: value for FFS plug and PCS receptacle mated (with PTFE insulator). Impedance measured 50 Ω with a RG-174 A/U cable and 75 Ω with a RG-179 B/U cable. FFA + PCA Color of connectors in anodized aluminum alloy Standard IEC 96-2 CCTU 10-01A MIL-C-17 6 7 RG.58 C/U RG.142 B/U 50.3.1 3 RG.174 A/U 50.2.1 1 2 5 2 4 1 4 3 8 8 RG.178 B/U RG.179 B/U RG.180 B/U RG.187 A/U RG.188 A/U RG.196 A/U RG.316 /U 50.1.1 75.2.1 75.2.2 50.2.3 50.1.2 50.2.2 FFV + PCS Note: measured according to IEC-169-1-3 standard. Recommended cables Cable group FFS + PCS 120 1000 f (MHz) Other cable KX 15 Belden 8262 KX 3A Belden Lemo Belden 8216 CCH.99.281.505 83265 KX 21A KX 22A Belden 83269 Belden Dätwyler Storm H+S 83284 HF-2114 421 099 G02232D-60 Imp. (Ω) 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 75 ± 3 Ω 95 ± 5 Ω 75 ± 3 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω When ordering a connector with an aluminum alloy, the outer shell color must be chosen from the table variant listed below and included in the position of the part number. Reference A J N R T V Color blue yellow black red natural green 11 ® ® Part Number Example Straight plug with cable collet FFA 00 250 N T A C 29 Model: (page 13) Series: 00 Variant 2) Type: 250 = coaxial (50 Ω) Cable ø: N= C= = Housing: D K= L = G= Cable fixing type: C = with cable collet E = crimp brass nickel-plated brass chrome-plated brass gold-plated brass black chrome aluminum alloy PEEK 3) Contact type: A = male to solder C = male to crimp L = female to solder M = female to crimp = PTFE Insulator: T L = PEEK FFA.00.250.NTAC29 = straight plug with cable collet, series 00, coaxial type (50 Ω), outer shell in nickel-plated brass, PTFE insulator, male solder contact, C type collet of 2.9 mm diameter. Straight receptacle ERA 00 250 N T L Model: (page 16) Series: 00 Variant 2) Type: 250 = coaxial (50 Ω) Contact type: A = male to solder C = male to print L = female to solder M = female to print N= C= Housing: D = K= L = brass nickel-plated brass chrome-plated 1) brass gold-plated brass black chrome 1) aluminum alloy 1) = PTFE Insulator: T L = PEEK ERA.00.250.NTL = fixed receptacle, nut fixing, series 00, coaxial type (50 Ω), outer shell in nickel-plated brass, PTFE insulator, female solder contact. Straight fixed coupler RAD 00 250 N T M Model: (page 21) Variant 2) Series: 00 Contact type 4): A = male-female C = male-male E = male-male-female 5) F = female-female-male 5) L = female-male M = female-female Type: 250 = coaxial (50 Ω) N= C= Housing: D = K= L = brass nickel-plated brass chrome-plated brass gold-plated brass black chrome aluminum alloy = PTFE Insulator: T L = PEEK RAD.00.250.NTM = straight fixed coupler, nut fixing, series 00, coaxial type (50 Ω), outer shell in nickel-plated brass, PTFE insulator, female-female contact. Note: 1) treatment not available for the printed circuit models 2) the “variant” position in the reference is used to specify the anodized color of the housing in aluminum alloy (page 11) or models with a collet nut for fitting a strain relief “Z”. The strain relief can be ordered separately as indicated in the “Accessories” section. 3) available for the FFA model only 4) concerning the straight fixed couplers with nut fixing RAD and SWH, the first contact type mentioned is always the contact at the flange end. 5) used only for models: FTA, FTL and FTY. 12 ® @@@@@@@@e? @@@@@@@@e? @@@@@@@@e? @@@@@@@@e?@@@@@@@@ @@@@@@@@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ Models @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@g @@g @@g @@g @@g @@g @@@@@@@@ @@@@@@@@ ® ?@@ ?@@ ?@@ ?@@ ?@@ ?@@ ?@@@@@@@@ ?@@@@@@@@ ?@@@@@@@@ ?@@@@@@@@ FFA Straight plug with cable collet ~26 Part number Cable group Note FFA.00.250.NTAC22 FFA.00.250.NTAC29 FFA.00.250.NTAC31 1 2-3-4 8 ● ● ● ø 6.4 ~18 S 4.5 M1 Cable assembly FFC Straight plug with flats on latch sleeve and cable collet ~26 Part number Cable group Note FFC.00.250.NTAC22 FFC.00.250.NTAC27 FFC.00.250.NTAC31 1 2-4 3-8 ● ● ● ø 6.4 ~18 S 4.5 S 5.5 M3 Cable assembly FFY Straight plug with cable collet ~33 ø 8.9 ø 8.6 ~25 Cable group Note FFY.00.250.NTAC52 6-7 ● M2 S8 Cable assembly FFA Straight plug with cable collet and nut for fitting a strain relief ~33.5 Part number Cable group Note FFA.00.250.NTAC22Z FFA.00.250.NTAC29Z FFA.00.250.NTAC31Z 1 2-3-4 8 ● ● ● ø 6.4 ~25.5 S6 M1 Note: the strain relief must be ordered separately (see page 29). Cable assembly FFA Straight plug with cable collet, PEEK outer shell ~33.5 Part number Cable group Note FFA.00.250.GTAC22 FFA.00.250.GTAC29 FFA.00.250.GTAC31 1 2-3-4 8 ● ● ● ~25.5 ø7 S7 Part number S6 M1 Cable assembly ● Available ● On request 13 ® ® FFE Straight plug with front sealing ring, cable collet and nut for fitting a strain relief ~33.5 Part number Cable group Note FFE.00.250.NTAC22Z FFE.00.250.NTAC29Z FFE.00.250.NTAC31Z 1 2-3-4 8 ● ● ● ø 7.4 ~25.5 S6 M1 FFF ~26 Cable assembly Straight plug, non-latching, with cable collet ø 6.4 ~18 S 4.5 Note: the strain relief must be ordered separately (see page 29). Part number Cable group Note FFF.00.250.NTAC22 FFF.00.250.NTAC29 FFF.00.250.NTAC31 1 2-3-4 8 ● ● ● M1 Cable assembly FFS Straight plug with cable crimping L ø 6.4 M S 5.5 S 5.5 Part number Cable group FFS.00.250.NTCE24 FFS.00.250.NTCE30 FFS.00.250.NTCE31 FFS.00.250.NTCE35 FFS.00.250.NTCE44 FFS.00.250.NTCE52 FFS.00.250.NTCE56 1 2 3-4 8 5 6 7 Dim. L M 31 31 31 31 31 34 31 Note ● ● ● ● ● ● ● 23 23 23 23 23 26 23 Note: the strain relief must be ordered separately (see page 29). M4 Cable assembly, crimp contact M5 Cable assembly, solder contact (on request) FFV Straight plug for cable crimping with improved screen efficiency L ø 6.4 M S 5.5 S 5.5 Part number Cable group FFV.00.250.NTCE24 FFV.00.250.NTCE30 FFV.00.250.NTCE31 FFV.00.250.NTCE35 FFV.00.250.NTCE44 FFV.00.250.NTCE52 FFV.00.250.NTCE56 1 2 3-4 8 5 6 7 Dim. L M 31 31 31 31 31 34 31 Note 23 23 23 23 23 26 23 ● ● ● ● ● ● ● Note: the strain relief must be ordered separately (see page 29). M4 Cable assembly, crimp contact M5 Cable assembly, solder contact (on request) FLA Elbow plug (90°) with cable collet 17.5 Part number Cable group Note FLA.00.250.NTAC22 FLA.00.250.NTAC27 FLA.00.250.NTAC31 1 2-4 3-8 ● ● ● 9 ~16 9.5 S 4.5 M6 14 Cable assembly ● Available ● On request ® ® FLS Elbow plug (90°) cable crimping 17.5 Part number 9 9.5 H FLS.00.250.NTAE24 FLS.00.250.NTAE31 FLS.00.250.NTAE35 FLS.00.250.NTAE52 FLS.00.250.NTAE56 M7 Cable group H (mm) Note 1 3-4 8 6 7 15 15 15 18 15 ● ● ● ● ● Cable assembly FLV Elbow plug (90°) cable crimping with improved screen efficiency Part number 17.5 9 FLV.00.250.NTAE24 FLV.00.250.NTAE30 FLV.00.250.NTAE31 FLV.00.250.NTAE35 FLV.00.250.NTAE52 FLV.00.250.NTAE56 H 9.5 M7 Cable group H (mm) Note 1 2 3-4 8 6 7 15 15 15 15 18 15 ● ● ● ● ● ● Cable assembly FAA Straight plug, non-latching, nut fixing 15.5 S9 9 2 maxi ø8 ø5 ø 10.3 M7x0.5 Part number Weight Note (g) FAA.00.250.NTA P5 S 6.3 2.5 ● Panel cut-out FAB Straight plug, non-latching, riveted fixing 10.8 8.8 ø 12 ø5 ø7 Part number Weight Note (g) FAB.00.250.NTA P1 1.8 maxi 2.5 ● Panel cut-out FPA Straight plug, non-latching, for printed circuit 7 17 Part number ø5 ø 0.9 ø 0.7 14 5.08 Weight Note (g) FPA.00.250.NTD 2.5 ● P11 PCB drilling pattern ● Available ● On request 15 ® ® FPL Elbow plug (90°), non-latching for printed circuit 7 ø5 5.08 Part number 17.5 Weight Note (g) 7 10 FPL.00.250.NTD 2.5 ● P10 PCB drilling pattern ø 0.7 ERA Fixed receptacle, nut fixing 15 S9 1 ø8 M7x0.5 ø 10.3 Part number 5.5 maxi S 6.3 ERA.00.250.NTL P5 Weight Note (g) 2.8 ● Panel cut-out ERN Fixed receptacle, nut fixing, with earthing tags 15 S9 1 ø8 M7x0.5 ø 10.3 Part number 5.5 maxi S 6.3 ERN.00.250.NTL P5 Weight Note (g) 2.8 ● Panel cut-out ERC Fixed receptacle, nut fixing, with slots in flange 15 Part number ø8 1.6 M7x0.5 1 ERC.00.250.NTL P3 Weight Note (g) 2.2 ● Panel cut-out ERE Fixed receptacle, nut fixing, with conical lead-in 15 S9 1 ø8 M7x0.5 ø 10.3 Part number 5.5 maxi S 6.3 ERE.00.250.NTL P5 2.8 Panel cut-out ● Available 16 Weight Note (g) ● On request ● ® ® ERT Straight receptacle without thread, force or adhesive fit 15 7 ± 0.03 1 Part number Weight Note (g) ø8 ERT.00.250.NTL P4 2.2 ● Panel cut-out ERM Fixed receptacle, nut fixing, with microswitch 20 S9 1 ø8 ø 10.3 A M7x0.5 Part number 5.5 maxi Weight Note (g) ERM.00.250.NTL S 6.3 P5 3.0 ● Panel cut-out B ECP Fixed receptacle with two nuts 15 2 ø 9.5 M7x0.5 ø9 Part number Weight Note (g) ECP.00.250.NTL P1 4 maxi 3.3 ● Panel cut-out EPA-EPB Straight receptacle for printed circuit 7 17 14 12 EPA.00.250.NTN EPB.00.250.NTN ø 6.8 ø 0.7 L (mm) Part number 5.08 L Weight Note (g) 3.4 3.3 ● ● P10 PCB drilling pattern EPC Straight receptacle for printed circuit with clearance under the body 7 17 5.08 Part number ø 6.8 ø 0.7 14 Weight Note (g) EPC.00.250.NTN 3.3 ● P10 PCB drilling pattern ● Available ● On request 17 ® ® EPE Fixed receptacle with two nuts, for printed circuit 17 14 7 2.5 S9 5.08 ø 0.7 P1 3.5 maxi Weight Note (g) EPE.00.250.NTN ø 10 10.3 M7x0.5 Part number S8 4.2 ● Panel cut-out P12 PCB drilling pattern EPL-EPM Elbow receptacle (90°) for printed circuit 7 ø 6.8 5.08 H (mm) Part number 10 13 EPL.00.250.NTN EPM.00.250.NTN 4.3 4.5 ● ● H 7 17.5 Weight Note (g) P10 PCB drilling pattern ø 0.7 EPK Elbow receptacle (90°) for printed circuit with clearance under the body 7 ø 6.8 5.08 Part number Weight Note (g) 17.5 10 7 EPK.00.250.NTN 4.2 ● P10 PCB drilling pattern ø 0.7 EPS Elbow receptacle (90°) with two nuts, for printed circuit 7 5.08 ø 10.3 M7x0.5 2.5 Part number S9 17.5 S8 EPS.00.250.NTN 18 ø 10 7 10 P1 ø 0.7 4 maxi Weight Note (g) 5.3 Panel cut-out P12 PCB drilling pattern ● Available ● On request ● ® 8.7 maxi 8.3 mini 1.7 maxi 1.3 mini 0.8 5.08 ® ø 1.5 EPN Straight receptacle for press mounting in pair on printed circuit 14 Part number Weight Note (g) 7 10.7 ø6 3.5 EPN.00.250.NTN ø 0.9 P9 3.6 ● PCB drilling pattern 2 EPY Elbow receptacle (90°) for printed circuit, with two vertical receptacles 5.08 2.42 ø 6.8 Part number EPY.00.250.NTN ● 14.3 10.5 17.8 7.5 12.8 P13 PCB drilling pattern 21.5 8 Weight Note (g) ø 0.7 PCA Free receptacle with cable collet Part number Cable group Note PCA.00.250.NTLC22 PCA.00.250.NTLC29 PCA.00.250.NTLC31 1 2-3-4 8 ● ● ● ø 6.5 ~25 S 4.5 M1 Cable assembly ● Available ● On request 19 ® ® PCS Free receptacle with cable crimping ø 6.5 L S 5.5 Part number Cable group PCS.00.250.NTME24 PCS.00.250.NTME30 PCS.00.250.NTME31 PCS.00.250.NTME35 PCS.00.250.NTME44 PCS.00.250.NTME52 1 2 3-4 8 5 6 Dim. Note L 30 30 30 30 30 33 ● ● ● ● ● ● Note: the strain relief must be ordered separately (see page 29). M4 Cable assembly, crimp contact M5 Cable assembly, solder contact (on request) PSA Fixed receptacle, nut fixing, with cable collet ~25 S9 ø 10.3 ø8 M7x0.5 S 4.5 Part number Cable group Note PSA.00.250.NTLC22 PSA.00.250.NTLC29 PSA.00.250.NTLC31 1 2-3-4 8 ● ● ● 1 5.5 maxi S 6.3 M1 Cable assembly P5 Panel cut-out PSS Fixedreceptacle,nut fixing,withcablecrimping Part number Cable group Note PSS.00.250.NTME24 PSS.00.250.NTME30 PSS.00.250.NTME31 PSS.00.250.NTME35 1 2 3-4 8 ● ● ● ● 30 1 S 5.5 M7x0.5 ø8 ø 10.3 S9 5.5 maxi S 6.3 Note: the strain relief must be ordered separately (see page 29). M4 Cable assembly, crimp contact M5 Cable assembly, solder contact (on request) P5 Panel cut-out PES Fixed receptacle, nut fixing, with cable crimping (back panel mounting) 30 S 5.5 2.5 maxi Part number Cable group Note PES.00.250.NTME31 PES.00.250.NTME35 3-4 8 ● ● 2.5 ø 10 M7x0.5 S 6.3 S8 Note: the strain relief must be ordered separately (see page 29). M4 Cable assembly, crimp contact M5 Cable assembly, solder contact (on request) P5 Panel cut-out FRT Straight plug with resistor or shorted 33 25 ø 6.4 Part number FRT.00.250.NTA00 FRT.00.250.NTA50 ● Available 20 Resistor Weight (g) Note shorted 50 Ω 1/8W 4.4 4.4 ● ● ● On request ® ® FLR Elbow plug (90°) with resistor 17.5 9 9.5 Part number 18.5 FLR.00.250.NTA50 Resistance Weight (g) Note 50 Ω 1/8W 5.6 ● RAD Fixed coupler, nut fixing 22 1 M7x0.5 5.5 maxi Part number ø 10.3 ø8 S9 RAD.00.250.NTM P5 S 6.3 Weight Note (g) 3.8 ● Panel cut-out RMA Free coupler 22 ø 6.5 Part number RMA.00.250.NTM Weight Note (g) 2.7 ● FTR Elbow plug (90°) with receptacle 18.5 Part number 17.5 9.5 9 FTR.00.250.NTA Weight Note (g) 5.4 ● FTA T-plug with two in-line receptacles 30 Part number 17.5 9.5 9 FTA.00.250.NTF ● Available Weight Note (g) 7.8 ● ● On request 21 ® ® FTL T-plug with two receptacles (90°) 28 9 20 Part number 18.5 FTL.00.250.NTF Weight Note (g) 7.1 ● FTY Straight plug with two parallel receptacles 29.5 7 21.5 7 16 Part number FTY.00.250.NTF Weight Note (g) 12.5 ● HGP Fixed receptacle, nut fixing, watertight 17 1.5 S9 ø 11 M7x0.5 ø 10.3 Part number HGP.00.250.NTLP P1 Weight Note (g) 4.2 ● Panel cut-out 8 maxi HGW Fixed receptacle, nut fixing, with rear sealing ring 15 S9 1 ø8 M7x0.5 ø 13 Part number HGW.00.250.NTLP P1 5.8 maxi Weight Note (g) 4.2 ● Panel cut-out EWF Fixed receptacle, nut fixing, vacuumtight (back panel mounting) 17 3 S9 S9 9 maxi ø 10.3 ø 11 M7x0.5 Part number EWF.00.250.NTLPV P1 4.2 Panel cut-out ● Available 22 Weight Note (g) ● On request ● ® ® EWV Fixed receptacle, vacuumtight 17 3 EWV.00.250.NTLPV ø 11 M7x0.5 Part number P2 Weight Note (g) 3.7 ● Panel cut-out SWH Fixed coupler, nut fixing, vacuumtight 24.5 1.5 M7x0.5 ø 11 ø 10.3 S9 7.5 maxi Part number SWH.00.250.NTMV P1 Weight Note (g) 5.2 ● Panel cut-out ABF Adaptor from LEMO plug to BNC receptacle 36 28 ø 11.5 Part number ABF.00.250.NTA Weight Note (g) 8.3 ● APF Adaptor from LEMO plug to CINCH receptacle Part number Colour of the ring Weight (g) Note 7 7 ● ● 43 APF.00.250.DTAB APF.00.250.DTAR white red ø 8.3 ø 6.4 34.5 ABA Adaptor from LEMO receptacle to BNC plug 28.5 ø 14.5 Part number ABA.00.250.NTL ● Available Weight Note (g) 18.7 ● ● On request 23 ® ® ABC Adaptor from LEMO receptacle to BNC receptacle 29.5 ABC.00.250.NTM Weight Note (g) 17 ● ABD Adaptor from LEMO receptacle to BNC fixed receptacle 29.5 S 16 S 17 Part number 19.5 1/2-28 UNEF - 2A ø 14.5 Part number ABD.00.250.NTM P7 25 ● Panel cut-out ABB Adaptor from LEMO fixed receptacle to BNC receptacle Part number ø 14 S 11 21.4 5 maxi 3/8-32 UNEF - 2A S 11.5 Weight Note (g) ABB.00.250.NTM P6 Weight Note (g) 9.4 ● Panel cut-out 9.5 maxi S 8.7 ACA Adaptor from LEMO receptacle to C plug 31 ø 19.5 Part number ACA.00.250.NTL Weight Note (g) 32 ● ACB Adaptor from LEMO receptacle to C receptacle 35.7 ø 19 Part number ACB.00.250.NTM ● Available 24 Weight Note (g) 50.3 ● On request ● ® ® AGG Adaptor from LEMO receptacle to General-Radio receptacle type 874 46.5 ø 20.6 Part number AGG.00.250.NTM Weight Note (g) 20 ● AGH Adaptor from LEMO receptacle to UHF plug 26 ø 18.5 Part number AGH.00.250.NTL Weight Note (g) 13.8 ● ANA Adaptor from LEMO receptacle to N plug 33.5 ø 20.5 Part number ANA.00.250.NTL Weight Note (g) 38 ● 5/8 - 24 UNEF - 2A ANB Adaptor from LEMO receptacle to N receptacle Part number 45.5 61.7 ● 5/8 - 24 UNEF - 2A ø 17.5 ANB.00.250.NTM Weight Note (g) ANC Adaptor from LEMO receptacle to N fixed receptacle 45 S 19 Part number 21.8 ANC.00.250.NTM P8 S 13.5 17 maxi Weight Note (g) 63.5 ● Panel cut-out ● Available ● On request 25 ® ASA Adaptor from LEMO receptacle to SMA plug 30 9 Part number ASA.00.250.NTL Weight Note (g) 4.9 ● S8 1 / 4 - 36 UNS - 2A ASB Adaptor from LEMO receptacle to SMA receptacle 30.8 Part number Weight Note (g) 4.6 ● 9 ASB.00.250.NTM S8 1 / 4 - 36 UNS - 2A ASF Adaptor from LEMO plug to SMA receptacle 31.8 23.8 Part number Weight Note (g) 4.6 ● 9 ASF.00.250.NTA S8 ASG Adaptor from LEMO plug to SMA plug 31 23 Part number 9 ® ASG.00.250.NTC Weight Note (g) 4.9 S8 ● Available ● On request ● ® ® Assembled Cables MFB models MSB models Delay lines Part number MFB.00.250.RTE005 MFB.00.250.RTE010 MFB.00.250.RTE020 MFB.00.250.RTE030 MFB.00.250.RTE040 MFB.00.250.RTE050 MFB.00.250.RTE060 MFB.00.250.RTE080 MFB.00.250.RTE100 MFB.00.250.RTE160 MFB.00.250.RTE200 MFB.00.250.RTE320 MFB.00.250.RTE640 Assembled Cables Delay (ns) 0.5 1.0 2.0 3.0 4.0 5.0 6.0 8.0 10.0 16.0 20.0 32.0 64.0 Part number MSB.00.250.RTE005 MSB.00.250.RTE010 MSB.00.250.RTE020 MSB.00.250.RTE030 MSB.00.250.RTE040 MSB.00.250.RTE050 MSB.00.250.RTE060 MSB.00.250.RTE080 MSB.00.250.RTE100 MSB.00.250.RTE160 MSB.00.250.RTE200 MSB.00.250.RTE320 MSB.00.250.RTE640 Length (cm) Part number MFB.00.250.LTE010 MFB.00.250.LTE020 MFB.00.250.LTE030 MFB.00.250.LTE040 MFB.00.250.LTE050 MFB.00.250.LTE060 MFB.00.250.LTE080 MFB.00.250.LTE100 MFB.00.250.LTE150 MFB.00.250.LTE200 MFB.00.250.LTE300 MFB.00.250.LTE400 MFB.00.250.LTE500 10 20 30 40 50 60 80 100 150 200 300 400 500 Part number MSB.00.250.LTE010 MSB.00.250.LTE020 MSB.00.250.LTE030 MSB.00.250.LTE040 MSB.00.250.LTE050 MSB.00.250.LTE060 MSB.00.250.LTE080 MSB.00.250.LTE100 MSB.00.250.LTE150 MSB.00.250.LTE200 MSB.00.250.LTE300 MSB.00.250.LTE400 MSB.00.250.LTE500 Note: the standard cable used to manufacture these cable assemblies is CCH.99.281.505 (LEMO) as per IEC.50.2.1 standard. On request, this type of cable can be replaced by other coaxial cables. Other cable lengths are available on request. Accessories Fitting of the cord Slide the plug into the loop of the cord. Place the loop into the groove in front of the collet nut and tighten the loop. BFA Plug Caps Part number BFA.00.100.PCSG Weight (g) 0.7 10.4 ø 7.5 10 60 Note: upon request, this cap can be supplied in black and the last letter “G” of the part number should be replaced with “N”. ● ● ● ● ● Body material: Polyoxymethylen (POM) grey Cord material: Polyamid 6, white O ring material: Silicone rubber Maximum operating temperature: 100°C Watertightness: IP61 according to IEC 529 27 ® ® BRA Blanking cap for fixed receptacle and free straight receptacle 9 3.2 10.4 ø 7.5 Part number 0.6 Note: upon request, this cap can be supplied in black and the last letter “G” of the part number should be replaced with “N”. 60 ø 3.2 BRA.00.200.PCSG Weight (g) ● O-ring material: Silicone rubber ● Maximum operating temperature: 100°C ● Watertightness: IP61 according to IEC 529 ● Body material: Polyoxymethylen (POM) grey ● Cord material: Polyamid 6, white Fitting of the cord Slide the receptacle into the loop of the cord. Place the loop into the groove in front of the collet nut and tighten the loop. BRD Blanking cap for free receptacle Part number 9 BRD.00.200.PCSG Weight (g) 0.5 3.2 10.4 ø 7.5 Note: upon request, this cap can be supplied in black and the last letter “G” of the part number should be replaced with “N”. 60 ● ● ● ● ● Body material: Polyoxymethylen (POM) grey Cord material: Polyamid 6, white O-ring material: Silicone rubber Maximum operating temperature: 100°C Watertightness: IP61 according to IEC 529 BRE Blanking cap for fixed receptacle, free receptacle and coupler 8.8 6.5 3.5 Part number ø 3.2 60 ø8 BRE.00.200.NAS ● ● ● ● ● Weight (g) 6.5 Body material: Brass (UNS C 38500), nickel-plated (3 µm) Cable material: Stainless steel O-ring material: Silicone rubber or FPM Maximum operating temperature: 250°C Watertightness: IP61 according to IEC 529 GCD Earthing cap ø8 øC L S7 Part number GCD.00.020.LA GCD.00.032.LA GCD.00.050.LA Cable group 1 2-3-4 6 Dim. L C 12 16 19 2.0 3.2 5.0 Note: the braid of the cable should be soldered onto the back of the cap. ● Material: Brass (UNS C 38500) gold-plated (0.5 µm) 28 ® ® FFS Crimp ferrule Part number øA FFS.00.160.DN FFS.00.161.MN FFS.00.162.DN FFS.00.163.DN FFS.00.164.DN FFV.00.160.DN Cable group Dim. øA 1 2-3-4 8 5 6 7 3.1 3.8 4.4 5.3 6.2 6.3 Note: receptacles and plugs to be crimped are always supplied with a crimp ferrule. To order this accessory separately, use the above part numbers. ● Material: Copper (UNS C 18700) nickel-plated (3µm) GMB Strain relief 22 ø Cable max min øA Part number GMB.00.025.DG GMB.00.028.DG GMB.00.032.DG A B G Color blue white grey Ref. J M N Color yellow brown black Ref. R S V 2.5 2.8 3.2 Nut for fitting the strain relief part nb 2.5 2.8 3.2 FFM.00.130.LN FFM.00.130.LN FFM.00.130.LN Note: a) for use with all crimp models and nut for fitting a strain relief b) the last letter of the part number “G” specifies the color grey. Refer to the table to the left to define another color and replace the letter “G” by the one corresponding to the color required. Color red orange green ● Material: Polyurethan (Desmopan 786) ● Operating temperature: -40°C + 80°C GRA Insulating washers Weight (g) Part number GRA.00.269.GG 0.1 Note: a) receptacles and plugs mounted on panels can be fitted with insulating washers. The nine colors available combined with those for the strain reliefs makes color coding possible. b) the last letter of the part number “G” specifies the color grey. Refer to the table below to define another color and replace the letter “G” with the one corresponding to the color required. 1.8 ø10 1 6.4 ● Material: Polyamid (PA.6) ● Operating temperature: -40°C + 80°C Ref. ø 8.8 Ref. 2.8 3.1 3.5 Dim. A A B G 3.5 maxi Color blue white grey Ref. J M N Color yellow brown black Ref. R S V Color red orange green GBA Locking washer ø9.5 ø7.1 Part number 1 GBA.00.250.FN Weight (g) 0.2 Note: receptacles and plugs are always supplied with a locking washer. To order this accessory separately, use the above part number. ● Material: Brass (UNS C 52100) nickel-plated (3 µm) 29 ® ® GBB Tapered washer ø9 2 ø 7.1 Part number Weight (g) GBB.00.250.LN 0.2 Note: to order this accessory separately, use the above part number. ● Material: Brass (UNS C 38500) nickel-plated (3 µm) GEA Hexagonal nut 9 2 M7 x 0.5 Part number 10.3 GEA.00.240.LN Weight (g) 0.6 Note: receptacles and plugs are supplied with a hexagonal nut as standard. To order this accessory separately, use the above part number. The last letters “LN” of the part number refer to the nut material and treatment. If a nut in aluminum alloy is desired, replace the last letters of the part number by “PT”. ● Material: – Brass (UNS C 38500) nickel-plated (3 µm) – Aluminum alloy (AA 6012) natural anodized GEB Round nut Part number ø9 M7 x 0.5 4 GEB.00.240.LN Weight (g) 0.8 Note: to order this accessory separately, use the above part number. ● Material: Brass (UNS C 38500) nickel-plated (3 µm) GEC Conical nut Part number 8 M7 x 0.5 Weight (g) 2.5 GEC.00.240.LN 0.6 ø 10 Note: to order this accessory separately, use the above part number. ● Material: Brass (UNS C 38500) nickel-plated (3 µm) GCA Earthing Washer ø 9.5 0.4 ø 7.1 18.2 Part number GCA.00.255.LT Weight (g) 0.2 ● Material: Brass (UNS C 27400) treated CuSnZn (2 µm) 30 ® ® Tooling DCG Spanner for hexagonal nut 50 Part number of the nut 40 Part number DCG.91.149.0TN GEA.00.240.LN ● Material: Blackened steel ø 14 DCA Spanner for hexagonal nut with locator for flats on receptacle thread 65 maxi 50 Part number of the nut Part number DCA.91.149.0TN GEA.00.240.LN ● Material: Blackened steel ø 14 DCB Spanner for round nut 50 Part number of the nut 40 Part number DCB.91.119.0TN GEB.00.240.LN ● Material: Blackened steel ø 11 DCN Spanner for assembling plug with 3 latches ø9 12 42 Part number DCN.91.905.0TK ● Material: Blackened steel 31 ® ® DCP Collet nut wrench Part number M DCP.99.045.TC DCP.99.050.TC DCP.99.055.TC DCP.99.060.TC S1 L 70 78 78 78 Dimensions M N 2 2 2 2 10.5 12.6 12.6 12.6 S1 4.5 5.0 5.5 6.0 N S1 ● Material: Chrome-plated steel L DCR Extraction tool for plugs Part number DCR.91.106.PT 150 ø 12 ø 9.6 ● Material: Aluminum alloy Note: this type of tool has been produced in order to facilitate the mating and unmating of plugs and is particularly useful in high density applications. 6 DPE Crimping tool with die Part number DPE.99.123.1K DPE.99.123.8K DPE.99.124.3K DPE.99.125.2K DPE.99.176.2K Cable group 1 2-3-4 8 5 6-7 DPN Dies Part number DPN.99.123.1K DPN.99.123.8K DPN.99.124.3K DPN.99.125.2K DPN.99.176.2K A B for contacts 32 1 2-3-4 8 5 6-7 ● Die material: Blackened steel A B L Cable group for shield Die dimension For contacts For shield A B L A B 1.29 1.29 1.29 1.29 1.71 0.91 0.91 0.91 0.91 1.21 2.0 2.0 2.0 2.0 2.5 3.10 3.80 4.36 5.20 6.20 2.70 3.30 3.78 4.50 5.37 ® ® Cut-Out Panel cut-out B + 0.1 0 L mini e øA + 0.1 0 Model P1 HGP-HGW-SWH-ECP EPE-EPS-FAB-EWF P2 P3 P4 P5 EWV ERC ERT Other models 1) – – 0 7-0.02 7.1 P6 P7 P8 ABB ABD ANC 9.7 9.0 15.0 12.9 11.7 20.5 16.1 13.7 24.0 A 7.1 – 14.5 e – – 12.0 M7x0.5 – 9.0 M7x0.5 – – – 6.5 14.5 – – – – B + 0.1 0 L mini Dimensions B L Cut-out øA + 0.1 0 Note: 1) If these models are used with a tapered washer GBB, the panel cut-out must be according P1. Recommended mounting nut torque: 2.5 Nm. PCB drilling pattern Cut-out L1 mini Model L1 mini ø A + 00.1 B B ø A + 00.1 B B = = = = L mini øC + 0.1 0 L mini øC P9 P10 P11 P12 EPN Other models FPA EPE-EPS P13 EPY A Dimensions B L L1 C 0.9 0.8 5.08 5.08 – 8.0 2.0 2.9 – 0.8 0.8 0.8 0.8 5.08 8.0 5.08 14.5 5.08 9.0 2.9 9.4 3.9 1.0 0.8 0.8 + 0.1 0 33 ® ® Terminated Instructions Terminating of plugs and straight receptacles with cable collet 5 M1 4 M2 M3 3 1 Straight plug 2 5 Free receptacle 3 4 5 1 Fixed receptacle nut fixing 1. Cable preparation First place the strain relief (if to be used) on the cable. Strip the cable according to dimensions below. L ± 0.2 S ± 0.2 T ± 0.2 2. Cable group T M1 S L T M2 S L T M3 S L 1-2-3-4-8 6-7 4 – 4.5 – 8 – – 7.5 – 8.5 – 13 5 – 5 – 8 – Cable termination 2.1 Place the collet nut ➀ and the collet ➁ on the cable. Fold back the shield braid onto the conical part of the collet, and trim to the outer edge of the collet Solder 2.2 Slide the subassembly ➂ to trap the shield braid and solder the center conductor into the contact. Solder 2.3 Slide the insulator ➃ onto the subassembly ➂ until it rests against the earthing sleeve of the subassembly ➂. 2.4 Slide the assembly into the connector outer shell ➄. Screw the collet nut ➀ into the connector outer shell ➄ using the appropriate tool and tighten to a torque of 0.25 Nm (see “Tooling” on page 31 and 32). Push the strain relief (if used) onto the collet nut. Note: these terminating instructions apply to the following models: M1 = FFA, FFE, FFF, PCA, PSA M2 = FFY M3 = FFC 34 ® Terminating of plugs and straight receptacles with cable crimping (crimp contact) 4 ® M4 2 3 Straight plug 1 4 Free receptacle 3 2 4 Fixed receptacle nut fixing 1. Cable preparation First place the strain relief (if to be used) on the cable. Strip the cable according to dimensions below. L ± 0.2 S ± 0.2 Cable group T M4 S L 1-2-3-4-5-8 6-7 7 7 15 15 19.5 21.5 T ± 0.2 2. Cable termination 2.1 Place crimp ferrule ➀ on the cable. Widen the shield braid. Slide the subassembly ➁ into the cable until the insulator rests against the dielectric and the cable conductor is visible through the contact inspection hole. Crimp 2.2 Crimp the contact with the LEMO crimping tool using the square hole (see “Tooling” on page 32). Gently pull the cable in order to check the crimping. Crimp 2.3 Slide the crimp ferrule ➀ onto the braiding until it rests against the crimp backnut of the subassembly ➁. Crimp with the same LEMO crimping tool using the hexagonal opening. Slide the insulator ➂ onto the subassembly ➁. 2.4 Slide the assembly into the connector shell ➃ and screw it onto the subassembly ➁. Tighten using the appropriate tool to a torque of 0.25 Nm (see “Tooling” on page 31 and 32). Push the strain relief (if used) onto the crimp ferrule ➀. Note: these terminating instructions apply to the following models: M4 = FFS, FFV, PCS, PSS, PES 35 ® ® Terminating of plugs and straight receptacles with cable crimping (solder contact) 4 M5 2 3 Straight plug 1 4 Free receptacle 3 2 4 Fixed receptacle nut fixing 1. Cable preparation First place the strain relief (if to be used) on the cable. Strip the cable according to dimensions below. L ± 0.2 S ± 0.2 Cable group T M5 S L 1-2-3-4-5-8 6-7 5 5 12 12 17 19 T ± 0.2 2. Cable terminating 2.1 Place the crimp ferrule ➀ on the cable. Widen the shield braid. Slide the subassembly ➁ over the cable until the insulator rests against the dielectric and the cable conductor is visible through the contact solder hole. 2.2 Solder the conductor through the hole. Solder Solder 2.3 Slide the crimp ferrule ➀ onto the shield until it rests against the crimp backnut of the subassembly ➁. Crimp with the LEMO crimping tool using the hexagonal opening (see “Tooling” on page 32). Slide the insulator ➂ onto the subassembly ➁. 2.4 Slide the assembly into the connector shell ➃ and screw it onto the subassembly ➁. Tighten using the appropriate tool to a torque of 0.25 Nm (see tooling on pages 31 and 32). Push the strain relief (if used) onto the crimp ferrule. Note: these terminating instructions apply to the following models: M5 = FFS, FFV, PCS, PSS, PES 36 ® Terminating of elbow plugs (90°) with cable collet 3 4 M6 and cable crimp ® M7 5 2 3 4 2 1 1 1. First place the strain relief (if to be used) on the cable. Strip the cable according to dimensions below. L ± 0.2 S ± 0.2 T ± 0.2 2. Solder 1. Cable preparation Cable group 1-2-3-4-8 First place the strain relief (if to be used) on the cable. Strip the cable according to dimensions below. L ± 0.2 S ± 0.2 T ± 0.2 T M6 S L 1 3.5 6.5 2. Cable terminating Cable preparation Cable group T M7 S L 1-2-3-4-8 6-7 1 3 4.5 4.5 9 11 Cable terminating 2.1 Place the crimp ferrule ➀ and collet ➁ on the cable. Fold back the shield braid onto the conical part of the collet, and trim to outer edge of the collet. 2.1 Place the cable crimp ferrule ➀ on the cable and widen the braiding. 2.2 Slide the assembly into the connector shell ➂ and tighten the collet nut ➀ using the appropriate tool to a torque of 0.25 Nm (see “Tooling” on page 31 and 32). Check that the cable conductor rests in the contact slot, solder the conductor through the hole. 2.2 Slide the cable into the connector shell ➁. Check that cable conductor rests in the contact slot, tin solder the conductor through the hole. Slide the crimp ferrule ➀ over the braiding until it reaches the connector shell ➁. Crimp with the LEMO crimp tool using the hexagonal opening (see “Tooling” on page 32). Solder 2.3 Place the insulating sleeve ➃ over the soldered contact. 2.3 Place the insulating sleeve ➂ over the soldered contact. 2.4 Close the access hole with the flat screw ➄. Push the strain relief (if used) onto the collet nut ➀. 2.4 Close the connector hole with the flat screw ➃. Push the strain relief (if used) onto the crimping tube ➀. Note: these terminating instructions apply to the following models: Note: these terminating instructions apply to the following models: M6 = FLA M7 = FLS, FLV 37 ® ® Recommended coaxial cables Dimensions and characteristics Standard / Part number (supplier) Imp. (Ω) Conductor Construction Mat. MIL-C-17 CCTU 10-01A CEI 96-2 RG.58C/U KX 15 50-3-1 50 ± 2 Ω 19x0.18 - 50 ± 2 Ω 50-2-1 50-1-1 75-2-1 75-2-2 50-2-3 50-1-2 50-2-2 RG.142B/U RG.174A/U RG.178B/U RG.179B/U RG.180B/U RG.187A/U RG.188A/U RG.196A/U RG.316/U KX 3A KX 21A KX 22A Construction and dimensions Dielectric Shield ø Mat. ø Mat. ø Sheath Mat. ø Weight kg/100 m CuSn 0.90 PE 2.95 CuSn 3.60 PVC* 4.95 3.80 solid CuStAg 0.95 PTFE 2.95 CuAg CuAg 2nd : 4.20 FEP 4.95 6.60 50 ± 2 Ω 50 ± 2 Ω 75 ± 3 Ω 95 ± 5 Ω 75 ± 3 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 7x0.16 7x0.10 7x0.10 7x0.10 7x0.10 7x0.18 7x0.10 7x0.18 CuSt CuStAg CuStAg CuStAg CuStAg CuStAg CuStAg CuStAg 0.48 0.30 0.30 0.30 0.30 0.54 0.30 0.54 PE PTFE PTFE PTFE PTFE PTFE PTFE PTFE 1.50 0.87 1.50 2.60 1.50 1.50 0.87 1.50 CuSn CuAg CuAg CuAg CuAg CuAg CuAg CuAg 2.00 1.40 2.00 3.10 2.00 2.00 1.37 2.10 PVC* FEP FEP FEP PTFE PTFE PTFE FEP 2.60 1.80 2.50 3.60 2.60 2.60 2.10 2.50 1.10 0.85 1.50 3.20 1.60 1.60 1.10 1.60 50-2-1 50-3-1 50-1-1 50-2-2 50-2-1 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 50 ± 2 Ω 7x0.16 19x0.18 7x0.10 7x0.17 7x0.17 7x0.16 7x0.18 CuSt CuSn CuStAg CuStAg CuStAg Cu Cu 0.48 0.90 0.30 0.51 0.51 0.48 0.54 PE PE PTFE PTFE PTFE PE PE 1.52 2.95 0.86 1.52 1.52 1.32 1.50 CuSn CuSn CuAg CuAg CuAg Cu Cu 1.9 2.2 PVC PVC FEP PTFE FEP PVC PoF 2.55 4.95 1.85 2.60 2.50 2.70 2.80 1.15 1.30 8216 8262 83265 83269 83284 HF-2114 CCH.99.281.505 (Belden) (Belden) (Belden) (Belden) (Belden) (Dätwyler) (Lemo)1) 421.099 (Storm) - 50 ± 2 Ω 7x0.16 CuStAg 0.50 PTFE 1.52 CuAg CuAg 1st : 2.00 2nd : 2.50 FEP 3.05 1.95 G02232D-60 (H+S) - 50 ± 2 Ω 7x0.16 Cu 0.50 PE 1.50 CuAg CuSn 1st : 1.95 2nd : 2.50 PVC 3.10 2.10 Notes: all dimensions are in millimeters. 1) Fire resistant according IEC 332-1. Cu CuAg CuSn CuSt CuStAg Bare copper Silver-plated copper Tinned copper Copper-plated steel Silvered copper plated steel FEP PE PoF PTFE Extruded Fluorethylenpropylen Polyethylen Polyolefin Wrapped or extruded Polytetrafluorethylen PVC PVC* Polyvinylchlorid Polyvinylchlorid (Qual.lla MIL-C-17) Technical tables VSWR effect on transmitted power VSWR VSWR (dB) 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 0 0.1 0.2 0.3 0.3 0.4 0.5 0.6 0.7 0.7 0.8 0.9 1.0 38 Return loss (dB) 46.1 40.1 36.6 34.2 32.3 30.7 29.4 28.3 27.3 26.4 25.7 24.9 Transmiss. Reflected Transmit. Reflected loss voltage power power (dB) coefficient (%) (%) 0.000 0.000 0.000 0.001 0.003 0.003 0.004 0.005 0.006 0.008 0.010 0.012 0.014 0.00 0.00 0.01 0.01 0.03 0.02 0.03 0.03 0.04 0.04 0.05 0.05 0.06 100.0 100.0 100.0 100.0 100.0 99.9 99.9 99.9 99.9 99.8 99.8 99.7 99.7 0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.1 0.1 0.2 0.2 0.3 0.3 VSWR VSWR (dB) Return loss (dB) 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.1 1.1 1.2 1.3 1.4 1.4 1.5 1.6 1.7 1.7 1.8 1.9 1.9 24.3 23.7 23.1 22.6 22.1 21.7 21.2 20.8 20.4 20.1 19.7 19.4 19.1 Transmiss. Reflected Transmit. Reflected loss voltage power power (dB) coefficient (%) (%) 0.016 0.019 0.021 0.024 0.027 0.030 0.033 0.036 0.039 0.043 0.046 0.050 0.054 0.06 0.07 0.07 0.07 0.08 0.08 0.09 0.09 0.10 0.10 0.10 0.11 0.11 99.6 99.6 99.5 99.5 99.4 99.3 99.2 99.2 99.1 99.0 98.9 98.9 98.8 0.4 0.4 0.5 0.5 0.6 0.7 0.8 0.8 0.9 1.0 1.1 1.1 1.2 ® ® Conversion millimeters-inches Tables (mm) (in) (mm) (in) (mm) (in) (mm) (in) (mm) (in) 0.02 0.03 0.10 0.16 0.18 0.20 0.30 0.40 0.48 0.50 0.51 0.54 0.60 0.70 0.80 0.86 0.87 0.90 0.91 0.95 1.00 1.21 1.29 1.30 1.32 0.0007 0.0011 0.0039 0.0062 0.0071 0.0078 0.0118 0.0157 0.0188 0.0196 0.0201 0.0212 0.0236 0.0275 0.0315 0.0338 0.0342 0.0354 0.0358 0.0374 0.0393 0.0476 0.0507 0.0512 0.0519 1.37 1.40 1.50 1.52 1.60 1.70 1.71 1.80 2.00 2.10 2.20 2.42 2.50 2.60 2.70 2.80 2.95 3.00 3.05 3.10 3.20 3.30 3.50 3.78 3.80 0.0539 0.0551 0.0590 0.0598 0.0629 0.0669 0.0673 0.0708 0.0787 0.0826 0.0866 0.0953 0.0984 0.1023 0.1063 0.1102 0.1161 0.1181 0.1201 0.1220 0.1259 0.1299 0.1378 0.1488 0.1496 3.90 4.00 4.36 4.50 5.00 5.08 5.20 5.37 5.50 5.80 6.00 6.20 6.30 6.40 6.50 6.80 7.00 7.10 7.40 7.50 8.00 8.30 8.60 8.70 8.80 0.1535 0.1575 0.1716 0.1771 0.1968 0.1999 0.2047 0.2114 0.2165 0.2283 0.2362 0.2441 0.2480 0.2519 0.2559 0.2677 0.2755 0.2795 0.2913 0.2952 0.3149 0.3267 0.3385 0.3425 0.3464 8.90 9.00 9.40 9.50 9.60 9.70 10.00 10.30 10.40 10.50 10.70 10.80 11.00 11.50 11.70 12.00 12.60 12.90 13.00 13.70 14.00 14.30 14.50 15.00 15.50 0.3504 0.3543 0.3701 0.3740 0.3779 0.3818 0.3937 0.4055 0.4094 0.4134 0.4212 0.4252 0.4331 0.4527 0.4606 0.4724 0.4961 0.5078 0.5118 0.5393 0.5512 0.5629 0.5708 0.5905 0.6102 16.00 16.10 17.00 17.50 17.80 18.00 18.20 18.50 19.00 19.50 20.00 20.50 20.60 21.00 21.50 21.80 22.00 23.00 23.80 24.00 25.00 25.50 26.00 28.00 28.50 0.6299 0.6338 0.6693 0.6889 0.7007 0.7086 0.7165 0.7283 0.7480 0.7677 0.7874 0.8071 0.8110 0.8267 0.8464 0.8582 0.8661 0.9055 0.9370 0.9448 0.9842 1.0039 1.0236 1.1023 1.1220 (mm) 29.50 30.00 30.80 31.00 31.80 32.00 33.00 33.50 34.00 34.50 35.70 36.00 40.00 41.00 42.00 43.00 45.00 45.50 46.50 50.00 60.00 65.00 70.00 78.00 150.00 (in) 1.1614 1.1811 1.2125 1.2204 1.2519 1.2598 1.2992 1.3188 1.3385 1.3582 1.4055 1.4173 1.5748 1.6141 1.6535 1.6929 1.7716 1.7913 1.8307 1.9685 2.3622 2.5590 2.7559 3.0708 5.9055 39