ETC SPIF301

SPIF301
USB to Serial-ATA Controller
JUL. 14, 2008
Version 1.0
SunplusIT reserves the right to change this documentation without prior notice.
Information provided by SunplusIT is believed to be accurate and reliable.
However, SunplusIT makes no warranty for any errors which may appear in this document.
specifications before placing your order.
result from its use.
Contact SunplusIT to obtain the latest version of device
No responsibility is assumed by SunplusIT for any infringement of patent or other rights of third parties which may
In addition, SunplusIT products are not authorized for use as critical components in life support devices/ systems or aviation
devices/systems, where a malfunction or failure of the product may reasonably be expected to result in significant injury to the user, without the express written
approval of SunplusIT.
http://www.golon.net E-mail:[email protected]
Mr Wu 13798432566
SPIF301 Data Sheet
Table of Contents
PAGE
1. GENERAL DESCRIPTION .......................................................................................................................................................................... 3
1.1. INTRODUCTION ...................................................................................................................................................................................... 3
1.2. FEATURES ............................................................................................................................................................................................. 3
1.2.1. Overall Features ....................................................................................................................................................................... 3
1.3. USB FEATURES ..................................................................................................................................................................................... 3
1.4. SERIAL-ATA FEATURES .......................................................................................................................................................................... 3
1.5. APPLICATION FIELD ................................................................................................................................................................................ 3
2. REFERENCES ............................................................................................................................................................................................ 3
3. BLOCK DIAGRAM ...................................................................................................................................................................................... 4
4. SIGNAL DESCRIPTIONS............................................................................................................................................................................ 5
4.1. PIN DIAGRAM......................................................................................................................................................................................... 5
4.2. PIN DESCRIPTIONS ................................................................................................................................................................................ 6
4.3. SPIF301 PIN LISTING ............................................................................................................................................................................ 7
5. ELECTRICAL SPECIFICATIONS ............................................................................................................................................................... 9
5.1. POWER REQUIREMENT .......................................................................................................................................................................... 9
5.2. LDO DC CHARACTERISTICS................................................................................................................................................................... 9
5.3. ABSOLUTE MAXIMUM RATINGS ............................................................................................................................................................... 9
5.4. RECOMMENDED/TYPICAL OPERATING CONDITIONS ................................................................................................................................. 9
5.5. IO DC CHARACTERISTICS .................................................................................................................................................................... 10
6. PACKAGE/PAD LOCATIONS ................................................................................................................................................................... 11
6.1. PACKAGE INFORMATION ........................................................................................................................................................................11
6.1.1. 48 pin LQFP.............................................................................................................................................................................11
6.2. ORDERING INFORMATION ..................................................................................................................................................................... 13
6.3. STORAGE CONDITION AND PERIOD FOR PACKAGE ................................................................................................................................. 13
6.4. RECOMMENDED SMT TEMPERATURE PROFILE...................................................................................................................................... 13
7. DISCLAIMER............................................................................................................................................................................................. 15
8. REVISION HISTORY ................................................................................................................................................................................. 16
http://www.golon.net E-mail:[email protected]
2
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
USB 2.0 TO SERIAL-ATA HOST BRIDGE CONTROLLER
1. GENERAL DESCRIPTION
1.1. Introduction
1.3. USB Features
The SunplusIT SPIF301 is a high-quality single-chip solution for
„ Compliant with USB 2.0 specification and passed USB
USB to Serial-ATA (SATA) host bridge controller. It features an
certification.
USB high-speed device port and a SATA 1.5Gb/s host port which
„ Supports USB high speed (480Mbps) and full speed transfer
leads it to carry out elementary function to receive standard Mass
rate (12Mbps).
Storage Device Class (MSDC) SCSI command from USB host and
„ Supports Mass Storage Device Class bulk only transfer.
translate into ATA/ATAPI command to SATA device.
„ Supports the USB host controller for UHCI, OHCI, EHCI mode.
1.2. Features
1.2.1.
1.4. Serial-ATA Features
Overall Features
„ Single 5V power source.
„ Compliant with Serial-ATA 1.0a specification.
„ Fabricated in CMOS process with 1.8V core and 3.3V I/Os.
„ Supports Serial-ATA generation 1 transfer rate of 1.5Gb/s
„ Available in LQFP48-pin package.
„ Supports spread spectrum in receiver
„ Integrated Memory, USB PHY and SATA PHY have isolated
BIST.
„ Full scan for high production test coverage
1.5. Application Field
„ Supports Window 2000/XP/Vista, Linux, Mac 10 OS platform.
„
USB External HDD
„
Enclosures
„
Mobil Rack
„
Docking Station
2. REFERENCES
For more detailed information about the USB and SATA
technology, please refer to the following industry specifications:
„ Serial-ATA
/
High
Speed
Serialized
ATA
Attachment
specification, Revision 1.0a.
„ Universal Serial Bus Specification Revision 2.0.
http://www.golon.net E-mail:[email protected]
3
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
3. BLOCK DIAGRAM
I2C
UART_TX
I2C
manager
GPIO0
UART
GPIO0
POR_
Reset
R8051
SFR Bus
Link Layer
Link Layer
Physical
Layer
USB
SATA_CTR
SATA_Buffer
USB_CTR
USB_Buffer
DMA_CTRL
Physical
Layer
LDO
5V
3V3
1V8
SATA
Fig 3-1: SPIF301 Functional Block Diagram
http://www.golon.net E-mail:[email protected]
4
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
4. SIGNAL DESCRIPTIONS
4.1. Pin Diagram
Figure 4-1 SPIF301 Pin Diagram
http://www.golon.net E-mail:[email protected]
5
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
4.2. Pin Descriptions
Table 4-1: Pin Types
Pin Type
Pin Description
I/O
Bi-directional Pin
I
Input Pin
O
Output Pin
OD
Open Drain output Pin
A
Analog pin
USB
USB D+ D-
SATA
SATA TX+ TX- RX+ RX-
PWR_I
Power input
PWR_O
LDO power output
NC
NO connection
http://www.golon.net E-mail:[email protected]
6
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
4.3. SPIF301 Pin Listing
Table 4-2: SPIF301 Pin Listing
Pin
Pin Name
1
NC
2
TESTB
3
Type
Internal
resistor
Level
Pin Description
---
---
---
I
Pull High
3.3V
D1V8_CORE
PWR_I
---
+1.8V
4
DVSS_CORE
GND
---
0V
5
NC
---
---
---
6
REXT
A
---
---
7
USB_VDD_RX
PWR_I
---
+3.3V
8
USB_VSS_RX
GND
---
0V
USB Analog ground for PHY RX
9
DM
---
---
USB High Speed D-
10
DP
USB
---
---
11
USB_VDD_TX
PWR_I
---
+3.3V
12
USB_VSS_TX
GND
---
0V
13
Reserve
---
---
---
14
Reserve
---
---
---
15
Reserve
---
---
---
16
D3V3_IO
PWR_I
---
+3.3V
17
VSS_IO
GND
---
0V
18
NC
---
---
---
19
Reserve
---
---
---
20
Reserve
---
---
---
21
GPIO(0)
I
Pull Low
+3.3V
O
---
+3.3V
22
NC
---
---
---
23
NC
---
---
---
24
NC
---
---
---
USB
Low active TEST Mode
1 (default): Normal mode
0: TEST Mode
Digital Core Power 1.8v
Digital Core Ground
USB external reference resistor input.
Connect 12K ohm pull low resistor
USB Analog power 3.3V for PHY RX
USB High Speed D+
USB Analog power 3.3V for PHY TX
USB Analog Ground for PHY TX
Digital 3.3V Power for IO
Digital Ground for IO
General purpose I/O 0
25
XI
A
---
---
SATA Crystal Oscillator Input / External Clock Input
26
XO
A
---
---
SATA Crystal Oscillator Output
27
SATA_VDD
PWR_I
---
+1.8V
28
SATA_VSS
GND
---
0V
29
RXXT
A
---
SATA 1.8V Digital Power
SATA Digital Ground
SATA external reference resistor Input
---
Connect 1K(1%) ohm pull low resistor
30
RXP
SATA
---
---
SATA Differential Receive +
31
RXN
SATA
---
---
SATA Differential Receive –
32
SATA_AVSS
GND
---
0V
SATA Analog Ground
33
SATA_AVDD
PWR_I
---
+1.8V
34
SATA_AVSS
GND
---
0V
SATA Analog Ground
35
TXN
SATA
---
---
SATA Differential Transmit –
36
TXP
SATA
---
---
SATA Differential Transmit +
37
LED
OD
---
+3.3V
HDD active LED (low active)
38
RESET_B
I
Pull High
+3.3V
Low Active Reset
http://www.golon.net E-mail:[email protected]
7
SATA 1.8V Analog Power
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
Pin
Pin Name
39
I2C_SCL
40
I2C_SDA
41
UART_TX
42
VSS
43
VOUT_3V
44
VDD_5V
45
Type
Internal
resistor
Level
Pin Description
OD
Pull High
+3.3V
I2C Clock
I
Pull High
+3.3V
OD
Pull High
+3.3V
O
---
+3.3V
GND
---
0V
PWR_O
---
+3.3V
PWR_I
---
+5V
VOUT_1.8V
PWR_O
---
+1.8V
46
DVSS_IO
PWR_I
---
0V
47
D3V3_IO
GND
---
+3.3V
Digital 3.3V Power for IO
48
USB_VBUS
I
---
+3.3V
USB VBUS detect pin
I2C Data
UART TX
LDO Ground
LDO 3.3 voltage output
LDO 5 voltage input
LDO 1.8 voltage output (For IC internal use only)
Digital Ground for IO
Note1: Internal pull high resistor is 45Kohm in typical, internal pull low resistor is 55Kohm in typical
http://www.golon.net E-mail:[email protected]
8
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
5. ELECTRICAL SPECIFICATIONS
5.1. Power Requirement
Table 5-1: Total Power Dissipation (Typical , TA =25℃)
Symbol
Parameter
IIO
Limits
Condition
Unit
Min.
Typ.
Max.
Absolute digital I/O pad power supply
3.3V
1.0
4.5
6.0
mA
ICORE
Absolute digital core power supply
1.8V
8
18
25
mA
IAUSB
Absolute analog power supply for USB PHY
3.3V
0
25
30
mA
IASATA
Absolute analog power supply for SATA PHY
1.8V
64
68
80
mA
5.2. LDO DC Characteristics
Table 5-2:
LDO DC Characteristics (Typical , TA =25℃)
Symbol
Parameter
Limits
Condition
Unit
Min.
Typ.
Max.
4.5
5
5.5
V
VDD_5V
Input voltage
VOUT_33V
3.3V output voltage
@VDD_5 = 5V
2.97
3.3
3.63
V
VOUT_1.8V
1.8V output voltage
@VDD_5 = 5V
1.71
1.8
1.91
V
I(VOUT_3.3V)
3.3V Output current
@VDD_5 = 5V, VOUT_3.3V = 3.3V
50
mA
I(VOUT_1.8V)
1.8V output current
@VDD_5 = 5V VOUT_1.8V = 1.8V
150
mA
I(VDD_5V)
5V input current
@I(VOUT_3.3V) = 50mA;
250
mA
I(VOUT_1.8V) = 150mA
5.3. Absolute Maximum Ratings
Table 5-3: Absolute Maximum Ratings (Typical , TA =25℃)
Symbol
Limits
Parameter
Unit
Min.
Typ.
Max.
Absolute digital I/O pad power supply voltage
2.97
3.3
3.63
V
VCORE
Absolute digital power supply
1.71
1.8
1.91
V
VAUSB
Absolute analog power supply voltage for USB PHY
2.97
3.3
3.63
V
VASATA
Absolute analog power supply voltage for SATA PHY
1.71
1.8
1.91
V
Absolute storage temperature
-20
25
105
℃
VIO
TSTR
5.4. Recommended/Typical Operating Conditions
Table 5-4: Recommended/Typical Operating Conditions
Symbol
Limits
Parameter
Unit
Min.
Typ.
Max.
VCORE
Operating digital power supply voltage
1.71
1.8
1.91
V
VIO
Operating digital I/O pad supply voltage
2.97
3.3
3.63
V
VAUSB
Operating analog power supply voltage for USB PHY
2.97
3.3
3.63
V
VASATA
Operating analog power supply voltage for SATA PHY
1.71
1.8
1.91
0
25
70
V
℃
TSTR
Operating temperature
http://www.golon.net E-mail:[email protected]
9
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
5.5. IO DC Characteristics
Table 5-5:
IO DC Characteristics
0
(Testing condition: VCORE =1.8V VAUSB, = 3.3V, VASATA = 1.8V Ta =25 C, unless otherwise noted)
Symbol
Parameter
Limits
Condition
VIL
Input low voltage
CMOS
Unit
Min.
Typ.
Max.
-0.3
-
0.8
V
VIH
Input high voltage
CMOS
2.0
-
Vio+0.3
V
VTH
Threshold point
CMOS
1.45
1.59
1.77
V
VT
Schmitt trig. Low to High threshold point
CMOS
1.9
Schmitt trig. high to low threshold point
CMOS
1.3
V
Input leakage current
CMOS
±10
µA
IOZ
Tri-state output leakage current
CMOS
±10
µA
RPU
Pull-up resistor
CMOS
45
KΩ
RPD
Pull-down resistor
CMOS
55
KΩ
+
VT
-
II
V
VOL
Output low voltage
CMOS, @ IOL =2mA
-
-
0.4
V
VOH
Output high voltage
CMOS @ IOH =5mA
2.4
-
-
V
IOL
Low level output current
@ VOL =0.4v
2
mA
IOH
High level output current
@ VOH =2.4v
5
mA
http://www.golon.net E-mail:[email protected]
10
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
6. PACKAGE/PAD LOCATIONS
6.1. Package Information
6.1.1. 48 pin LQFP
http://www.golon.net E-mail:[email protected]
11
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
Fig 6-1: SPIF301 in LQFP-48 package
http://www.golon.net E-mail:[email protected]
12
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
6.2. Ordering Information
IC package:
H = Green Package
Package Type:
L = LQFP
Body Size + Pin count:
23 = 48 pins (7 x 7 x 1.4 mm)
Serial Number: [= 1 ~ 9 ]
Example:
Product Number
Package Type
SPIF301 - HL23X
Green Package form - LQFP 48
6.3. Storage Condition and Period for Package
Package
Moisture sensitivity level
Max. Reflow temperature
Floor life storage condition
Dry pack
LQFP48
LEVEL 3
255 +5/-0℃
168Hrs @ ≦30℃/ 60% R.H.
Yes
Note1: Please refer to the IPC/JEDEC standard J-STD-020A and the EIA JEDEC stand JESD22-A112, or the “CAUTION Note” on dry pack bag.
6.4. Recommended SMT Temperature Profile
This “Recommended” temperature profile is a rough guideline for
PPF(Pre-Plated Frame) product with 63/37 solder paste, we
SMT process reference. Most of SUNPLUSIT lead frame based
recommend 240℃~245℃ for peak temperature.
product choice Matte Tin and Sn/Bi for plating recipe. For
http://www.golon.net E-mail:[email protected]
13
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
http://www.golon.net E-mail:[email protected]
14
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
7. DISCLAIMER
The information appearing in this publication is believed to be accurate.
Integrated circuits sold by SunplusIT are covered by the warranty and patent indemnification provisions stipulated in the terms of sale only.
SUNPLUSIT makes no warranty, express, statutory implied or by description regarding the information in this publication or regarding the
freedom of the described chip(s) from patent infringement.
MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.
prices at any time without notice.
FURTHERMORE, SUNPLUSIT MAKES NO WARRANTY OF
SUNPLUSIT reserves the right to halt production or alter the specifications and
Accordingly, the reader is cautioned to verify that the data sheets and other information in this
publication are current before placing orders.
Products described herein are intended for use in normal commercial applications.
Applications involving unusual environmental or reliability requirements, e.g. military equipment or medical life support equipment, are
specifically not recommended without additional processing by SUNPLUSIT for such applications.
Please note that application circuits
illustrated in this document are for reference purposes only.
http://www.golon.net E-mail:[email protected]
15
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0
SPIF301 Data Sheet
8. REVISION HISTORY
Date
Revision #
2008/07/14
1.0
Description
SPIF301 data sheet initial version
http://www.golon.net E-mail:[email protected]
Page
16
16
Mr Wu 13798432566
JUL. 14, 2008
Version: 1.0