AD AD9861BCPRL-80

Mixed-Signal Front-End (MxFE™) Baseband
Transceiver for Broadband Applications
AD9861
FEATURES
Receive path includes dual 10-bit analog-to-digital
converters with internal or external reference, 50 MSPS
and 80 MSPS versions
Transmit path includes dual 10-bit, 200 MSPS digital-toanalog converters with 1×, 2×, or 4× interpolation and
programmable gain control
Internal clock distribution block includes a programmable
phase-locked loop and timing generation circuitry,
allowing single-reference clock operation
20-pin flexible I/O data interface allows various interleaved
or noninterleaved data transfers in half-duplex mode and
interleaved data transfers in full-duplex mode
Configurable through register programmability or
optionally limited programmability through mode pins
Independent Rx and Tx power-down control pins
64-lead LFCSP package (9 mm × 9 mm footprint)
3 configurable auxiliary converter pins
APPLICATIONS
Broadband access
Broadband LAN
Communications (modems)
FUNCTIONAL BLOCK DIAGRAM
VIN+A
ADC
DATA
MUX
AND
LATCH
VIN–A
VIN+B
ADC
Rx DATA
VIN–B
I/O
INTERFACE
CONTROL
I/O
INTERFACE
CONFIGURATION
BLOCK
LOW-PASS
INTERPOLATION
FILTER
FLEXIBLE
I/O BUS
[0:19]
IOUT+A
DATA
LATCH
AND
DEMUX
DAC
IOUT–A
IOUT+B
DAC
Tx DATA
IOUT–B
AUX
ADC
AUX
DAC
ADC CLOCK
CLKIN
AUX
DAC
DAC CLOCK
PLL
AUX
ADC
AD9861
AUX
DAC
03606-0-001
Figure 1.
GENERAL DESCRIPTION
The AD9861 is a member of the MxFE family—a group of
integrated converters for the communications market. The
AD9861 integrates dual 10-bit analog-to-digital converters
(ADC) and dual 10-bit digital-to-analog converters (TxDAC®).
Two speed grades are available, -50 and -80. The -50 is optimized for ADC sampling of 50 MSPS and less, while the -80 is
optimized for ADC sample rates between 50 MSPS and 80 MSPS.
The dual TxDACs operate at speeds up to 200 MHz and
include a bypassable 2× or 4× interpolation filter. Three
auxiliary converters are also available to provide required
system level control voltages or to monitor system signals. The
AD9861 is optimized for high performance, low power, small
form factor, and to provide a cost-effective solution for the
broadband communication market.
The AD9861 uses a single input clock pin (CLKIN) to generate
all system clocks. The ADC and TxDAC clocks are generated
within a timing generation block that provides user programmable options such as divide circuits, PLL multipliers, and switches.
A flexible, bidirectional 20-bit I/O bus accommodates a variety
of custom digital back ends or open market DSPs.
In half-duplex systems, the interface supports 20-bit parallel
transfers or 10-bit interleaved transfers. In full-duplex systems,
the interface supports an interleaved 10-bit ADC bus and an
interleaved 10-bit TxDAC bus. The flexible I/O bus reduces pin
count and, therefore, reduces the required package size on the
AD9861 and the device to which it connects.
The AD9861 can use either mode pins or a serial programmable interface (SPI) to configure the interface bus, operate the
ADC in a low power mode, configure the TxDAC interpolation
rate, and control ADC and TxDAC power-down. The SPI
provides more programmable options for both the TxDAC path
(for example, coarse and fine gain control and offset control for
channel matching) and the ADC path (for example, the internal
duty cycle stabilizer, and twos complement data format).
The AD9861 is packaged in a 64-lead LFCSP (low profile, fine
pitched, chip scale package). The 64-lead LFCSP footprint is
only 9 mm × 9 mm, and is less than 0.9 mm high, fitting into
tightly spaced applications such as PCMCIA cards
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2003 Analog Devices, Inc. All rights reserved.
AD9861
TABLE OF CONTENTS
Tx Path Specifications...................................................................... 3
Theory of Operation ...................................................................... 22
Rx Path Specifications...................................................................... 4
System Block ............................................................................... 22
Power Specifications......................................................................... 5
Rx Path Block.............................................................................. 22
Digital Specifications........................................................................ 5
Tx Path Block.............................................................................. 24
Timing Specifications....................................................................... 6
Auxiliary Converters.................................................................. 27
Absolute Maximum Ratings............................................................ 7
Digital Block................................................................................ 30
ESD Caution.................................................................................. 7
Programmable Registers............................................................ 42
Pin Configuration and Pin Function Descriptions...................... 8
Clock Distribution Block .......................................................... 45
Typical Performance Characteristics ........................................... 10
Outline Dimensions ....................................................................... 49
Terminology .................................................................................... 21
Ordering Guide .......................................................................... 50
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 52
AD9861
Tx PATH SPECIFICATIONS
Table 1. AD9861-50 and AD9861-80
FDAC = 200 MSPS; 4× interpolation; RSET = 4.02 kΩ; differential load resistance of 100 Ω1; TxPGA = 20 dB, AVDD = DVDD = 3.3 V,
unless otherwise noted
Parameter
Tx PATH GENERAL
Resolution
Maximum DAC Update Rate
Maximum Full-Scale Output Current
Full-Scale Error
Gain Mismatch Error
Offset Mismatch Error
Reference Voltage
Output Capacitance
Phase Noise (1 kHz Offset, 6 MHz Tone)
Output Voltage Compliance Range
TxPGA Gain Range
TxPGA Step Size
Tx PATH DYNAMIC PERFORMANCE
(IOUTFS = 20 mA; FOUT = 1 MHz)
SNR
SINAD
THD
SFDR, Wideband (DC to Nyquist)
SFDR, Narrowband (1 MHz Window)
1
Temp
Test Level
Full
Full
Full
Full
25°C
Full
Full
Full
25°C
Full
Full
Full
IV
IV
IV
V
IV
IV
V
V
V
IV
V
V
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
Min
10
Unit
Bits
MHz
mA
1%
–3.5
–0.1
+3.5
+0.1
20
0.10
% FS
% FS
V
pF
dBc/Hz
V
dB
dB
60.8
60.7
−77.5
76.0
81.0
dB
dB
dBc
dBc
dBc
1.23
5
–115
–1.0
60.2
59.7
64.6
72.5
TxDAC
50Ω
03606-0-030
Figure 2. Diagram Showing Termination of 100 Ω Differential
Load for Some TxDAC Measurements
Rev. 0 | Page 3 of 52
Max
200
20
See Figure 2 for description of the TxDAC termination scheme.
50Ω
Typ
+1.0
−65.8
AD9861
Rx PATH SPECIFICATIONS
Table 2. AD9861-50 and AD9861-80
FADC = 50 MSPS for the AD9861-50, 80 MSPS for the AD9861-80; internal reference; differential analog inputs,
ADC_AVDD = DVDD = 3.3V, unless otherwise noted
Parameter
Rx PATH GENERAL
Resolution
Maximum ADC Sample Rate
Gain Mismatch Error
Offset Mismatch Error
Reference Voltage
Reference Voltage (REFT–REFB) Error
Input Resistance (Differential)
Input Capacitance
Input Bandwidth
Differential Analog Input Voltage Range
Rx PATH DC ACCURACY
Integral Nonlinearity (INL)
Differential Nonlinearity (DNL)
Aperature Delay
Aperature Uncertainty (Jitter)
Input Referred Noise
AD9861-50 Rx PATH DYNAMIC PERFORMANCE
(VIN = –0.5 dBFS; FIN = 10 MHz)
SNR
SINAD
SINAD
THD (Second to Ninth Harmonics)
SFDR, Wideband (DC to Nyquist)
Crosstalk between ADC Inputs
AD9861-80 Rx PATH DYNAMIC PERFORMANCE
(VIN = –0.5 dBFS; FIN = 10 MHz)
SNR
SINAD
THD (Second to Ninth Harmonics)
SFDR, Wideband (DC to Nyquist)
Crosstalk between ADC Inputs
Temp
Test Level
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
V
IV
V
V
V
IV
V
V
V
V
25°C
25°C
25°C
25°C
25°C
V
V
V
V
V
Full
Full
25°C
Full
Full
Full
IV
IV
IV
IV
IV
V
55.5
55.6
58.5
Full
Full
Full
Full
Full
IV
IV
IV
IV
V
55.4
52.7
Rev. 0 | Page 4 of 52
Min
Typ
Max
10
50/80
–30
65.7
±0.2
±0.1
1.0
±6
2
5
30
2
+30
Unit
Bits
MSPS
% FS
% FS
V
mV
kΩ
pF
MHz
V p-p differential
±0.75
±0.75
2.0
1.2
450
LSB
LSB
ns
ps rms
uV
60
60
60
−71.5
73.5
80
dBc
dBc
dBc
dBc
dBc
dB
59.5
59.0
−67
67
80
−64.6
dBc
dBc
dBc
dBc
dB
AD9861
POWER SPECIFICATIONS
Table 3. AD9861-50 and AD9861-80
Analog and digital supplies = 3.3 V; FCLKIN = 50 MHz; PLL 4× setting; normal timing mode
Parameter
POWER SUPPLY RANGE
Analog Supply Voltage (AVDD)
Digital Supply Voltage (DVDD)
Driver Supply Voltage (DRVDD)
ANALOG SUPPLY CURRENTS
TxPath (20 mA Full-Scale Outputs)
TxPath (2 mA Full-Scale Outputs)
Rx Path (-80, at 80 MSPS)
RxPath (-80, at 40 MSPS, Low Power Mode)
RxPath (-80, at 20 MSPS, Ultralow Power Mode)
Rx Path (-50, at 50 MSPS)
RxPath (-50, at 50 MSPS, Low Power Mode)
RxPath (-50, at 16 MSPS, Ultralow Power Mode)
TxPath, Power-Down Mode
RxPath, Power-Down Mode
PLL
DIGITAL SUPPLY CURRENTS
TxPath, 1× Interpolation,
50 MSPS DAC Update for Both DACs,
Half-Duplex 24 Mode
TxPath, 2× Interpolation,
100 MSPS DAC Update for Both DACs,
Half-Duplex 24 Mode
TxPath, 4× Interpolation,
200 MSPS DAC Update for Both DACs,
Half-Duplex 24 Mode
RxPath Digital, Half-Duplex 24 Mode
Temp
Test Level
Min
Typ
Max
Unit
Full
Full
IV
IV
2.7
2.7
3.6
3.6
V
V
Full
IV
2.7
3.6
V
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
V
V
V
V
V
V
V
V
V
V
V
70
20
165
82
35
103
69
28
2
5
12
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Full
V
20
mA
Full
V
50
mA
Full
V
80
mA
Full
V
15
mA
DIGITAL SPECIFICATIONS
Table 4. AD9861-50 and AD9861-80
Parameter
LOGIC LEVELS
Input Logic High Voltage, VIH
Input Logic Low Voltage, VIL
Output Logic High Voltage, VOH (1 mA Load)
Output Logic Low Voltage, VOL (1 mA Load)
DIGITAL PIN
Input Leakage Current
Input Capacitance
Minimum RESET Low Pulse Width
Digital Output Rise/Fall Time
Temp
Test Level
Min
Full
Full
Full
Full
IV
IV
IV
IV
DRVDD – 0.7
Full
Full
Full
Full
IV
IV
IV
IV
Rev. 0 | Page 5 of 52
Typ
Max
0.4
DRVDD – 0.6
0.4
12
3
5
2.8
4
Unit
V
V
V
V
µA
pF
Input Clock Cycles
ns
AD9861
TIMING SPECIFICATIONS
Table 5. AD9861-50 and AD9861-80
Parameter
INPUT CLOCK
CLKIN Clock Rate (PLL Bypassed)
PLL Input Frequency
PLL Ouput Frequency
TxPATH DATA
Setup Time (HD20 Mode, Time Required Before Data Latching
Edge)
Hold Time (HD20 Mode, Time Required After Data Latching
Edge)
Latency 1× Interpolation (data in until peak output response)
Latency 2× Interpolation (data in until peak output response)
Latency 4× Interpolation (data in until peak output response)
RxPATH DATA
Output Delay (HD20 Mode, tOD)
Latency
Temp
Test Level
Min
Typ
Full
Full
Full
IV
IV
IV
1
16
32
Full
V
5
Full
V
–1.5
Full
Full
Full
V
V
V
7
35
83
Full
V
–1.5
Full
V
5
Max
Unit
200
200
350
MHz
MHz
MHz
ns (see Clock
Distribution Block
section)
ns (see Clock
Distribution Block
section)
DAC Clock Cycles
DAC Clock Cycles
DAC Clock Cycles
ns (see Clock
Distribution Block
section)
ADC Clock Cycles
Table 6. Explanation of Test Levels
Level
I
II
III
IV
V
VI
Description
100% production tested.
100% production tested at 25°C and guaranteed by design and characterization at specified temperatures.
Sample tested only.
Parameter is guaranteed by design and characterization testing.
Parameter is a typical value only.
100% production tested at 25°C and guaranteed by design and characterization for industrial temperature range.
Rev. 0 | Page 6 of 52
AD9861
ABSOLUTE MAXIMUM RATINGS
Table 7.
Parameter
Electrical
AVDD Voltage
DRVDD Voltage
Analog Input Voltage
Digital Input Voltage
Digital Output Current
Environmental
Operating Temperature Range
(Ambient)
Maximum Junction Temperature
Lead Temperature (Soldering, 10 sec)
Storage Temperature Range
(Ambient)
Thermal Resistance
Rating
3.9 V max
3.9 V max
–0.3 V to AVDD + 0.3 V
–0.3 V to DVDD – 0.3 V
5 mA max
64-lead LFCSP (4-layer board):
θJA = 24.2 (paddle soldered to ground plan, 0 LPM Air)
θJA = 30.8 (paddle not soldered to ground plan, 0 LPM Air)
–40°C to +85°C
150°C
300°C
–65°C to +150°C
Stresses above those listed under the Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 7 of 52
AD9861
SPI_CS
TxPWRDWN
RxPWRDWN
ADC_AVDD
REFT
ADC_AVSS
VIN+A
VIN–A
VREF
VIN–B
VIN+B
ADC_AVSS
REFB
ADC_AVDD
PLL_AVDD
PLL_AVSS
PIN CONFIGURATION AND PIN FUNCTION DESCRIPTIONS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
SPI_DIO
SPI_CLK
SPI_SDO/AUX_SPI_SDO
ADC_LO_PWR/AUX_SPI_CS
DVDD
DVSS
AVDD
IOUT–A
IOUT+A
AGND
REFIO
FSADJ
AGND
IOUT+B
IOUT–B
AVDD
1
48 CLKIN
2
47 AUXADC_REF
3
46 RESET
4
45 AUX_DACC/AUX_ADCB
5
44 L0
43 L1
6
7
AD9861
42 L2
8
TOP VIEW
(Not to Scale)
41 L3
9
40 L4
10
39 L5
11
38 L6
12
37 L7
13
36 L8
14
35 L9
15
34 AUX_SPI_CLK
16
33 IFACE1
IFACE2
IFACE3
U9
U8
U7
U6
U5
U4
U3
U2
U1
U0
AUX_DACA/AUX_ADCA2
AUX_DACB/AUX_ADCA1
DRVDD
DRVSS
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
03606-0-019
Figure 3. Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
1
2
3
4
5, 31
6, 32
7, 16, 50, 51, 61
8, 9
10, 13, 49, 53, 59
11
12
14, 15
17
18
19–28
29
30
33
Name1
SPI_DIO
(Interp1)
SPI_CLK
(Interp0)
SPI_SDO/AUXSPI_SDO
(FD/HD)
ADC_LO_PWR/AUX_SPI_CS
DVDD
DVSS
AVDD
IOUT–A, IOUT+A
AGND, AVSS
REFIO
FSADJ
IOUT+B, IOUT−B
IFACE2
(10/20)
IFACE3
U9–U0
AUX1
AUX2
IFACE1
Description2, 3
SPI: Serial Port Data Input.
No SPI: Tx Interpolation Pin, MSB.
SPI: Serial Port Shift Clock.
No SPI: Tx Interpolation Pin, LSB.
SPI: 4-Wire Serial Port Data Output/Data Output Pin for AuxSPI.
No SPI: Configures Full-Duplex or Half-Duplex Mode.
ADC Low Power Mode Enable. Defined at power-up. CS for AuxSPI.
Digital Supply.
Digital Ground.
Analog Supply.
DAC A Differential Output.
Analog Ground.
Tx DAC Band Gap Reference Decoupling Pin.
Tx DAC Full-Scale Adjust Pin.
DAC B Differential Output.
SPI: Buffered CLKIN. Can be configured as system clock output.
No SPI: For FD: Buffered CLKIN; For HD20 or HD10 : 10/20 Configuration Pin.
Clock Output.
Upper Data Bit 9 to Upper Data Bit 0.
Configurable as either AuxADC_A2 or AuxDAC_A.
Configurable as either AuxADC_A1 or AuxDAC_B.
SPI: For FD: TxSYNC; For HD20, HD10, or Clone: Tx/Rx.
No SPI: FD >> TxSYNC; HD20 or HD10: Tx/Rx.
Rev. 0 | Page 8 of 52
AD9861
Pin No.
34
35–44
45
46
47
48
52
54, 55
56
57, 58
60
62
63
64
Name1
AUX_SPI_CLK
L9–L0
AUX3
RESET
AUX_ADC_REF
CLKIN
REFB
VIN+B, VIN−B
VREF
VIN−A, VIN+A
REFT
RxPwrDwn
TxPwrDwn
SPI_CS
Description2, 3
CLK for AuxSPI.
Lower Data Bit 9 to Lower Data Bit 0.
Configurable as either AuxADC_B or AuxDAC_C.
Chip Reset When Low.
Decoupling for AuxADC On-Chip Reference.
Clock Input.
ADC Bottom Reference.
ADC B Differential Input.
ADC Band Gap Reference.
ADC A Differential Input.
ADC Top Reference.
Rx Analog Power-Down Control.
Tx Analog Power-Down Control.
SPI: Serial Port Chip Select. At power-up or reset, this must be high.
No SPI: Tie low to disable SPI and use mode pins. This pin must be tied low.
1
Underlined pin names and descriptions apply when the device is configured without a serial port interface, referred to as no SPI mode.
Pin function depends if the serial port is used to configure the AD9861 (called SPI mode) or if mode pins are used to configure the AD9861 (called No SPI mode). The
differences are indicated by the SPI and No SPI labels in the description column.
3
Some pin descriptions depend on the interface configuration, full-duplex (FD), half-duplex interleaved data (HD10), half-duplex parallel data (HD20), and a half-duplex
interface similar to the AD9860 and AD9862 data interface called clone mode (Clone). Clone mode requires a serial port interface.
2
Rev. 0 | Page 9 of 52
AD9861
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBFS)
–40
–50
–60
–70
–80
–60
–70
0
5
15
10
FREQUENCY (MHz)
20
–100
–110
25
0
Figure 4. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path
Digitizing 2 MHz Tone
0
–10
–20
–20
–30
–30
AMPLITUDE (dBFS)
0
–40
–50
–60
–70
–60
–70
–90
03606-0-033
–80
5
10
15
FREQUENCY (MHz)
20
25
–50
–90
0
20
–40
–80
–110
10
15
FREQUENCY (MHz)
Figure 7. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path
Digitizing 1 MHz and 2 MHz Tones
–10
–100
5
03606-0-034
–110
03606-0-032
03606-0-031
–90
–100
AMPLITUDE (dBFS)
–50
–80
–90
–100
–110
0
25
Figure 5. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path
Digitizing 5 MHz Tone
5
10
15
FREQUENCY (MHz)
20
25
Figure 8. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path
Digitizing 5 MHz and 8 MHz Tones
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBFS)
AMPLITUDE (dBFS)
–40
–40
–50
–60
–70
–80
–40
–50
–60
–70
–80
–90
03606-0-035
–90
–100
–110
0
5
10
15
FREQUENCY (MHz)
20
03606-0-036
AMPLITUDE (dBFS)
TYPICAL PERFORMANCE CHARACTERISTICS
–100
–110
25
0
Figure 6. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path
Digitizing 24 MHz Tone
5
10
15
FREQUENCY (MHz)
20
25
Figure 9. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path
Digitizing 20 MHz and 25 MHz Tones
Rev. 0 | Page 10 of 52
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBFS)
–40
–50
–60
–70
–80
–40
–50
–60
–70
–80
–90
03606-0-037
–90
–100
–110
0
5
10
15
FREQUENCY (MHz)
20
–100
–110
0
25
Figure 10. AD9861-50 Rx Path Single-Tone FFT of Rx Channel B Path
Digitizing 76 MHz Tone
62
03606-0-038
AMPLITUDE (dBFS)
AD9861
5
10
15
FREQUENCY (MHz)
20
25
Figure 13. AD9861-50 Rx Path Dual-Tone FFT of Rx Channel A Path
Digitizing 70 MHz and 72 MHz Tones
62
NORMAL POWER @ 50MSPS
10.0
NORMAL POWER @ 50MSPS
9.8
LOW POWER ADC @ 25MSPS
9.6
LOW POWER ADC @ 25MSPS
59
59
56
9.2
8.8
ULTRALOW POWER ADC
@ 16MSPS
53
9.0
56
ULTRALOW POWER ADC
@ 16MSPS
53
ENOB (Bits)
SINAD (dBc)
SNR (dBc)
9.4
8.6
50
0
5
15
10
INPUT FREQUENCY (MHz)
20
8.2
50
25
0
Figure 11. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
SNR Performance vs. Input Frequency
80
20
8.0
25
Figure 14. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
SINAD Performance vs. Input Frequency
–50
LOW POWER ADC @ 25MSPS
–55
75
NORMAL POWER @ 50MSPS
–60
THD (dBc)
70
65
ULTRALOW POWER ADC
@ 16MSPS
–65
NORMAL POWER @ 50MSPS
–70
60
ULTRALOW POWER ADC
@ 16MSPS
–75
50
0
5
10
15
INPUT FREQUENCY (MHz)
20
03606-0-042
55
03606-0-041
SFDR (dBc)
15
10
INPUT FREQUENCY (MHz)
5
LOW POWER ADC @ 25MSPS
–80
0
25
5
10
15
INPUT FREQUENCY (MHz)
20
25
Figure 15. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
THD Performance vs. Input Frequency
Figure 12. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
SFDR Performance vs. Input Frequency
Rev. 0 | Page 11 of 52
03606-0-040
03606-0-039
8.4
AD9861
70
90
–90
80
50
70
40
–80
–70
THD
60
–60
50
–50
20
40
–40
10
30
–30
IDEAL SNR
30
THD (dBFS)
60
SFDR (dBFS)
SNR (dBc)
SFDR
0
0
–5
–10
–15
–20
–25
–30
INPUT AMPLITUDE (dBFS)
–35
–40
20
–45
0
Figure 16. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
SNR Performance vs. Input Amplitude
–5
–10
–15
–20
–25
–30
INPUT AMPLITUDE (dBFS)
–35
–20
–40
03606-0-044
03606-0-043
SNR
Figure 19. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
THD and SFDR Performance vs. Input Amplitude
62
62
10.0
9.9
AVE (+25°C)
SINAD (dBc)
AVE (+85°C)
59
9.4
58
9.3
9.2
57
9.1
03606-0-045
57
3.0
3.3
ADC_AVDD VOLTAGE (V)
56
2.7
3.6
9.0
3.6
3.0
3.3
ADC_AVDD VOLTAGE (V)
Figure 20. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
SINAD Performance vs. ADC_AVDD and Temperature
Figure 17. AD9861-50 Rx Path at 50 MSPS, 10 MHz Input Tone
SNR Performance vs. ADC_AVDD and Temperature
70
–70.0
–70.5
71
–71.0
72
AVE (+85°C)
–71.5
SFDR (dBc)
AVE (+85°C)
–72.0
AVE (+25°C)
–72.5
–73.0
73
74
AVE (+25°C)
75
AVE (–40°C)
–73.5
76
AVE (–40°C)
–74.0
–74.5
–75.0
3.6
77
03606-0-047
THD (dBc)
9.5
3.3
3.0
INPUT AMPLITUDE (dBFS)
03606-0-048
SNR (dBc)
AVE (+85°C)
9.6
58
56
2.7
9.7
60
60
59
9.8
AVE (–40°C)
AVE (+25°C)
78
3.6
2.7
3.3
3.0
INPUT AMPLITUDE (dBFS)
2.7
Figure 21. AD9861-50 Rx Path Single-Tone SFDR Performance vs.
ADC_AVDD and Temperature
Figure 18. AD9861-50 Rx Path Single-Tone THD Performance vs.
ADC_AVDD and Temperature
Rev. 0 | Page 12 of 52
ENOB (Bits)
61
03606-0-046
AVE (–40°C)
61
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBFS)
–40
–50
–60
–70
–80
–60
–70
0
5
10
15
20
25
FREQUENCY (MHz)
30
35
–100
–110
0
40
Figure 22. AD9861-80 Rx Path Single-Tone FFT of Rx Channel B Path
Digitizing 2 MHz Tone
0
–10
–20
–20
–30
–30
AMPLITUDE (dBFS)
0
–40
–50
–60
–70
–60
–70
–90
03606-0-051
–80
5
10
15
20
25
FREQUENCY (MHz)
30
35
25
–50
–90
0
20
–40
–80
–110
10
15
FREQUENCY (MHz)
Figure 25. AD9861-80 Rx Path Dual-Tone FFT of Rx Channel A Path
Digitizing 1 MHz and 2 MHz Tones
–10
–100
5
03606-0-052
–110
03606-0-050
03606-0-049
–90
–100
AMPLITUDE (dBFS)
–50
–80
–90
–100
–110
0
40
Figure 23. AD9861-80 Rx Path Single-Tone FFT of Rx Channel B Path
Digitizing 5 MHz Tone
5
10
15
FREQUENCY (MHz)
20
25
Figure 26. AD9861-80 Rx Path Dual-Tone FFT of Rx Channel A Path
Digitizing 5 MHz and 8 MHz Tones
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBFS)
AMPLITUDE (dBFS)
–40
–40
–50
–60
–70
–80
–40
–50
–60
–70
–80
–90
03606-0-053
–90
–100
–110
0
5
10
15
20
25
FREQUENCY (MHz)
30
35
03606-0-054
AMPLITUDE (dBFS)
AD9861
–100
–110
0
40
Figure 24. AD9861-80 Rx Path Single-Tone FFT of Rx Channel B Path
Digitizing 24 MHz Tone
5
10
15
FREQUENCY (MHz)
20
25
Figure 27. AD9861-80 Rx Path Dual-Tone FFT of Rx Channel A Path
Digitizing 20 MHz and 25 MHz Tones
Rev. 0 | Page 13 of 52
AD9861
62
62
10.0
LOW POWER ADC @ 40MSPS
ULTRALOW POWER ADC @ 16MSPS
LOW POWER ADC @ 40MSPS
9.8
ULTRALOW POWER ADC @ 16MSPS
9.6
59
59
9.4
56
NORMAL POWER @ 80MSPS
9.2
ENOB (Bits)
SINAD (dBc)
SNR (dBc)
NORMAL POWER @ 80MSPS
9.0
56
8.8
8.6
53
53
50
0
5
25
10
15
20
INPUT FREQUENCY (MHz)
03606-0-056
03606-0-055
8.4
8.2
50
30
0
Figure 28. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
SNR Performance vs. Input Frequency and Power Setting
5
10
15
20
INPUT FREQUENCY (MHz)
25
8.0
30
Figure 31. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
SINAD Performance vs. Input Frequency and Power Setting
–50
85
LOW POWER ADC @ 40MSPS
–55
80
–60
THD (dBc)
SFDR (dBc)
ULTRALOW POWER
ADC @ 16MSPS
75
70
–65
LOW POWER ADC @ 40MSPS
–70
65
03606-0-057
–75
60
0
5
10
15
INPUT FREQUENCY (MHz)
20
ULTRALOW POWER
ADC @ 16MSPS
NORMAL POWER @ 80MSPS
–80
25
Figure 29. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
SFDR Performance vs. Input Frequency and Power Setting
0
5
10
15
INPUT FREQUENCY (MHz)
20
03606-0-058
NORMAL POWER @ 80MSPS
25
Figure 32. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
THD Performance vs. Input Frequency and Power Setting
70
60
–80
80
–70
70
50
SFDR
IDEAL SNR
30
–50
50
THD
–40
20
60
SFDR (dBFS)
THD (dBFS)
40
40
10
–30
0
0
–5
–10
–15
–20
–25
–30
INPUT AMPLITUDE (dBFS)
–35
–40
30
–20
–45
0
Figure 30. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
SNR Performance vs. Input Amplitude
–5
–10
–15
–20
–25
–30
INPUT AMPLITUDE (dBFS)
–35
20
–40
Figure 33. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
THD Performance vs. Input Amplitude
Rev. 0 | Page 14 of 52
03606-0-060
SNR
03606-0-059
SNR (dBc)
–60
AD9861
62
62
61
61
10.0
9.9
SINAD (dBc)
59
AVE (+25°C)
AVE (+85°C)
9.6
AVE (+25°C)
59
9.5
9.4
58
58
9.3
AVE (–40°C)
56
2.7
3.0
3.3
ADC_AVDD VOLTAGE (V)
9.2
57
03606-0-065
57
9.1
56
2.7
3.6
Figure 34. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
SNR Performance vs. AVDD and Temperature
ENOB (Bits)
9.7
60
9.0
3.6
3.0
3.3
ADC_AVDD VOLTAGE (V)
03606-0-066
60
SNR (dBc)
9.8
AVE (–40°C)
AVE (+85°C)
Figure 37. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
SINAD Performance vs. AVDD and Temperature
70
65
69
66
AVE (+85°C)
68
67
AVE (+25°C)
AVE (–40°C)
67
AVE (–40°C)
68
AVE (+85°C)
64
69
70
71
63
72
62
73
61
60
2.7
3.0
3.3
ADC_AVDD VOLTAGE (V)
03606-0-062
SFDR (dBc)
65
03606-0-061
THD (dBc)
AVE (+25°C)
66
74
75
2.7
3.6
3.0
3.3
ADC_AVDD VOLTAGE (V)
Figure 35. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
THD Performance vs. AVDD and Temperature
Figure 38. AD9861-80 Rx Path at 80 MSPS, 10 MHz Input Tone
SFDR Performance vs. AVDD and Temperature
120
180
160
NORM
NORM
80
LP
60
40
ULP
03606-0-063
20
0
0
10
20
30
FCLK (MHz)
40
120
100
LP
80
60
40
ULP
20
0
0
50
Figure 36. AD9861-50 ADC_AVDD Current vs. Sampling Rate for
Different ADC Power Levels
140
03606-0-064
ADC AVDD CURRENT (mA)
100
ADC AVDD CURRENT (mA)
3.6
10
20
30
40
50
FCLK (MHz)
60
70
80
Figure 39. AD9861-80 ADC_AVDD Current vs. ADC Sampling Rate for
Different ADC Power Levels
Rev. 0 | Page 15 of 52
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBc)
–40
–50
–60
–70
–80
–60
–70
0
5
10
15
FREQUENCY (MHz)
20
–100
–110
25
0
Figure 40. AD9861 Tx Path 1 MHz Single-Tone Output FFT of Tx Path
with 20 mA Full-Scale Output into 33 Ω Differential Load
0
–10
–20
–20
–30
–30
AMPLITUDE (dBc)
0
–40
–50
–60
–70
–60
–70
–90
03606-0-070
–80
5
10
15
FREQUENCY (MHz)
20
25
–50
–90
0
20
–40
–80
–110
10
15
FREQUENCY (MHz)
Figure 43. AD9861 Tx Path 5 MHz Single-Tone Output FFT of Tx Path
with 20 mA Full-Scale Output into 33 Ω Differential Load
–10
–100
5
03606-0-071
–110
03606-0-069
03606-0-068
–90
–100
AMPLITUDE (dBc)
–50
–80
–90
–100
–110
25
0
Figure 41. AD9861 Tx Path 1 MHz Single-Tone Output FFT of Tx Path
with 20 mA Full-Scale Output into 60 Ω Differential Load
5
10
15
FREQUENCY (MHz)
20
25
Figure 44. AD9861 Tx Path 5 MHz Single-Tone Output FFT of Tx Path
with 20 mA Full-Scale Output into 60 Ω Differential Load
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBc)
AMPLITUDE (dBc)
–40
–40
–50
–60
–70
–80
–40
–50
–60
–70
–80
–90
03606-0-072
–90
–100
–110
0
5
10
15
FREQUENCY (MHz)
20
03606-0-073
AMPLITUDE (dBc)
AD9861
–100
–110
25
0
Figure 42. AD9861 Tx Path 1 MHz Single-Tone Output FFT of Tx Path
with 2 mA Full-Scale Output into 600 Ω Differential Load
5
10
15
FREQUENCY (MHz)
20
25
Figure 45. AD9861 Tx Path 5 MHz Single-Tone Output FFT of Tx Path
with 2 mA Full-Scale Output into 600 Ω Differential Load
Rev. 0 | Page 16 of 52
–50
–50
–60
–60
–70
–70
THD (dBc)
–80
–90
5
10
15
OUTPUT FREQUENCY (MHz)
20
–100
25
0
62
61
61
60
60
SINAD (dBc)
62
59
58
57
57
0
5
10
15
OUTPUT FREQUENCY (MHz)
20
20
25
59
58
56
10
15
OUTPUT FREQUENCY (MHz)
Figure 49. AD9861 Tx Path THD vs. Output Frequency of Tx Path
with 2 mA Full-Scale Output into 600 Ω Differential Load
03606-0-076
SINAD (dBc)
Figure 46. AD9861 Tx Path THD vs. Output Frequency of Tx Path with
20 mA Full-Scale Output into 60 Ω Differential Load
5
03606-0-077
0
03606-0-075
03606-0-074
–90
–100
56
0
25
Figure 47. AD9861 Tx Path SINAD vs. Output Frequency of Tx Path, with
20 mA Full-Scale Output into 60 Ω Differential Load
5
10
15
OUTPUT FREQUENCY (MHz)
20
25
Figure 50. AD9861 Tx Path SINAD vs. Output Frequency of Tx Path, with
2 mA Full-Scale Output into 600 Ω Differential Load
–70
–75
–75
–80
–80
IMD (dBc)
–70
–85
–90
–85
–90
03606-0-078
IMD (dBc)
–80
–95
0
5
10
15
OUTPUT FREQUENCY (MHz)
20
03606-0-079
THD (dBc)
AD9861
–95
25
0
Figure 48. AD9861 Tx Path Dual-Tone (0.5 MHz Spacing) IMD vs.
Output Frequency of Tx Path, with
20 mA Full-Scale Output into 60 Ω Differential Load
5
10
15
OUTPUT FREQUENCY (MHz)
20
25
Figure 51. AD9861 Tx Path Dual-Tone (0.5 MHz Spacing) IMD vs.
Output Frequency of Tx Path, with
2 mA Full-Scale Output into 600 Ω Differential Load
Rev. 0 | Page 17 of 52
AD9861
–30
–30
–40
–40
–50
–50
–60
–60
AMPLITUDE (dBc)
–70
–80
–90
–100
–130
7.5
–100
12.5
17.5
22.5
FREQUENCY (MHz)
–120
–130
18.75
32.5
27.5
Figure 52. AD9861 Tx Path FFT, 64-Carrier (Center Two Carriers Removed)
OFDM Signal over 20 MHz Bandwidth, Centered at 20 MHz, with
20 mA Full-Scale Output into 60 Ω Differential Load
–30
–30
–40
–40
–50
–50
–60
–60
–70
–80
–90
–100
19.25
19.75
20.25
FREQUENCY (MHz)
21.25
20.75
Figure 55. AD9861 Tx Path FFT, In-Band IMD Products of
OFDM Signal in Figure 52
AMPLITUDE (dBc)
–80
–90
–100
–110
03606-0-082
–110
–70
–120
–130
7.5
8.0
8.5
9.0
9.5 10.0 10.5 11.0
FREQUENCY (MHz)
11.5
12.0
03606-0-083
AMPLITUDE (dBc)
–90
03606-0-081
–120
–120
–130
27.5
12.5
Figure 53. AD9861 Tx Path FFT, Lower-Band IMD Products of
OFDM Signal in Figure 52
28.0
28.5
29.0
29.5 30.0 30.5 31.0
FREQUENCY (MHz)
31.5
32.0
32.5
Figure 56. AD9861 Tx Path FFT, Upper-Band IMD Products of
OFDM Signal in Figure 52
–30
–40
–40
–50
–50
–60
–60
AMPLITUDE (dBc)
–30
–70
–80
–90
–100
–110
–70
–80
–90
–100
–110
03606-0-084
AMPLITUDE (dBc)
–80
–110
03606-0-080
–110
–70
–120
–130
0
10
20
30
40
50
FREQUENCY (MHz)
60
70
03606-0-085
AMPLITUDE (dBc)
Figure 52 to Figure 57 use the same input data to the Tx path, a 64-carrier OFDM signal over a 20 MHz bandwidth, centered at 20 MHz.
The center two carriers are removed from the signal to observe the in-band intermodulation distortion (IMD) from the DAC output.
–120
–130
80
0
Figure 54. AD9861 Tx Path FFT of OFDM Signal in Figure 52,
with 1× Interpolation
10
20
30
40
50
FREQUENCY (MHz)
60
70
80
Figure 57. AD9861 Tx Path FFT of OFDM Signal in Figure 52,
with 4× Interpolation
Rev. 0 | Page 18 of 52
AD9861
–40
–50
–50
–60
–60
–70
–70
–80
–90
–100
–100
–110
–120
–120
6.2
6.4
6.6
6.8
7.0
7.2
7.4
FREQUENCY (MHz)
7.6
7.8
–130
–140
6.97
8.0
Figure 58. AD9861 Tx Path FFT, 256-Carrier (Center Four Carriers Removed)
OFDM Signal over 1.75 MHz Bandwidth, Centered at 7 MHz, with
20 mA Full-Scale Output into 60 Ω Differential Load
–50
–50
–60
–60
–70
–70
AMPLITUDE (dBc)
–40
–90
–100
–90
–100
–110
–120
03606-0-088
–110
–140
6.06
6.08
6.10
6.12
6.14
FREQUENCY (MHz)
6.16
7.03
7.02
–80
–120
–130
6.99
7.00
7.01
FREQUENCY (MHz)
Figure 61. AD9861 Tx Path FFT, In-Band IMD Products of
OFDM Signal in Figure 58
–40
–80
6.98
03606-0-089
–140
6.0
–130
–140
7.81
6.18
Figure 59. AD9861 Tx Path FFT, Lower-Band IMD Products of
OFDM Signal in Figure 58
7.83
7.85
7.87
7.89
FREQUENCY (MHz)
7.91
7.93
Figure 62. AD9861 Tx Path FFT, Upper-Band IMD Products of
OFDM Signal in Figure 52
–30
–40
–40
–50
–50
–60
–60
AMPLITUDE (dBc)
–30
–70
–80
–90
–100
–80
–90
–100
–110
03606-0-090
–110
–70
–120
–130
0
5
10
15
FREQUENCY (MHz)
20
03606-0-091
AMPLITUDE (dBc)
–90
–110
–130
AMPLITUDE (dBc)
–80
03606-0-087
AMPLITUDE (dBc)
–40
03606-0-086
AMPLITUDE (dBc)
Figure 58 to Figure 63 use the same input data to the Tx path, a 256-carrier OFDM signal over a 1.75 MHz bandwidth, centered at 7 MHz.
The center four carriers are removed from the signal to observe the in-band intermodulation distortion (IMD) from the DAC output.
–120
–130
25
0
Figure 60. AD9861 Tx Path FFT of OFDM Signal in Figure 52,
with 1× Interpolation
5
10
15
FREQUENCY (MHz)
20
25
Figure 63. AD9861 Tx Path FFT of OFDM Signal in Figure 52,
with 4× Interpolation
Rev. 0 | Page 19 of 52
AD9861
–40
–50
–50
–60
–60
–70
–70
–80
–90
–100
–100
–110
–120
–120
9
14
19
24
FREQUENCY (MHz)
29
–130
–140
22.6
34
Figure 64. AD9861 Tx Path FFT, 256-Carrier (Center Four Carriers Removed)
OFDM Signal over 23 MHz Bandwidth, Centered at 7 MHz, with
20 mA Full-Scale Output into 60 Ω Differential Load
–50
–50
–60
–60
–70
–70
AMPLITUDE (dBc)
–40
–90
–100
–110
22.8
22.9
23.0
23.1
FREQUENCY (MHz)
23.2
23.3
23.4
Figure 67. AD9861 Tx Path FFT, In-Band IMD Products of
OFDM Signal in Figure 64
–40
–80
22.7
–120
–80
–90
–100
–110
–130
–140
10.5
10.7
10.9
11.1
11.3 11.5 11.7 11.9
FREQUENCY (MHz)
12.1
12.3
03606-0-095
03606-0-094
–120
–130
–140
33.5
12.5
Figure 65. AD9861 Tx Path FFT, Lower-Band IMD Products of
OFDM Signal in Figure 64
33.7
33.9
34.1
34.3 34.5 34.7 34.9
FREQUENCY (MHz)
35.1
35.3
35.5
Figure 68. AD9861 Tx Path FFT, Upper-Band IMD Products of
OFDM Signal in Figure 64
–30
–40
–40
–50
–50
–60
–60
AMPLITUDE (dBc)
–30
–70
–80
–90
–100
–80
–90
–100
–110
03606-0-096
–110
–70
–120
–130
0
10
20
30
40
50
60
FREQUENCY (MHz)
70
80
03606-0-097
–140
AMPLITUDE (dBc)
–90
–110
–130
AMPLITUDE (dBc)
–80
03606-0-093
AMPLITUDE (dBc)
–40
03606-0-092
AMPLITUDE (dBc)
Figure 64 to Figure 69 use the same input data to the Tx path, a 256-carrier OFDM signal over a 23 MHz bandwidth, centered at 23 MHz.
The center four carriers are removed from the signal to observe the in-band intermodulation distortion (IMD) from the DAC output.
–120
–130
90
0
Figure 66. AD9861 Tx Path FFT of OFDM Signal in Figure 52
with 1× Interpolation
10
20
30
40
50
60
FREQUENCY (MHz)
70
80
90
Figure 69. AD9861 Tx Path FFT of OFDM Signal in Figure 52
with 4× Interpolation
Rev. 0 | Page 20 of 52
AD9861
TERMINOLOGY
Input Bandwidth
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Aperture Delay
The delay between the 50% point of the rising edge of the
CLKIN signal and the instant at which the analog input is
actually sampled.
Harmonic Distortion, Second
The ratio of the rms signal amplitude to the rms value of the
second harmonic component, reported in dBc.
Harmonic Distortion, Third
The ratio of the rms signal amplitude to the rms value of the
third harmonic component, reported in dBc.
Integral Nonlinearity
The deviation of the transfer function from a reference line
measured in fractions of an LSB using a “best straight line”
determined by a least square curve fit.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Crosstalk
Coupling onto one channel being driven by a –0.5 dBFS signal
when the adjacent interfering channel is driven by a full-scale
signal.
Minimum Conversion Rate
Differential Analog Input Voltage Range
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differential
voltage is computed by observing the voltage on a single pin
and subtracting the voltage from the other pin, which is 180°
out of phase. Peak-to-peak differential is computed by rotating
the input phase 180° and taking the peak measurement again.
Then the difference is computed between both peak
measurements.
Maximum Conversion Rate
The encode rate at which parametric testing is performed.
Differential Nonlinearity
The deviation of any code width from an ideal 1 LSB step.
Effective Number of Bits (ENOB)
The effective number of bits is calculated from the measured
SNR based on the following equation:
ENOB =
SNRMEASURED − 1.76 dB
6.02
Pulse Width/Duty Cycle
Pulse width high is the minimum amount of time that a signal
should be left in the logic high state to achieve rated performance; pulse width low is the minimum time a signal should be
left in the low state, logic low.
Full-Scale Input Power
Expressed in dBm, full-scale input power is computed using the
following equation:
⎛V 2
Z
Power FULLSCALE = 10 log ⎜ FULLSCALE − RMS INPUT
⎜
0
.
001
⎝
⎞
⎟
⎟
⎠
Gain Error
Gain error is the difference between the measured and ideal
full-scale input voltage range of the ADC.
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Output Propagation Delay
The delay between a differential crossing of CLK+ and CLK−
and the time when all output data bits are within valid logic
levels.
Power Supply Rejection Ratio
The ratio of a change in input offset voltage to a change in
power supply voltage.
Signal-to-Noise and Distortion (SINAD)
The ratio of the rms signal amplitude (set 1 dB below full-scale)
to the rms value of the sum of all other spectral components,
including harmonics, but excluding dc.
Signal-to-Noise Ratio (without Harmonics)
The ratio of the rms signal amplitude (set at 1 dB below full
scale) to the rms value of the sum of all other spectral
components, excluding the first five harmonics and dc.
Spurious-Free Dynamic Range (SFDR)
The ratio of the rms signal amplitude to the rms value of the
peak spurious spectral component. The peak spurious
component may or may not be a harmonic. It also may be
reported in dBc (i.e., degrades as signal level is lowered) or
dBFS (i.e., always related back to converter full scale). SFDR
does not include harmonic distortion components.
Worst Other Spur
The ratio of the rms signal amplitude to the rms value of the
worst spurious component (excluding the second and third
harmonics) reported in dBc.
Rev. 0 | Page 21 of 52
AD9861
THEORY OF OPERATION
SYSTEM BLOCK
The AD9861 is targeted to cover the mixed-signal front end
needs of multiple wireless communication systems. It features a
receive path that consists of dual 10-bit receive ADCs, and a
transmit path that consists of dual 10-bit transmit DACs
(TxDAC). The AD9861 integrates additional functionality
typically required in most systems, such as power scalability,
additional auxiliary converters, Tx gain control, and clock
multiplication circuitry.
The AD9861 minimizes both size and power consumption to
address the needs of a range of applications from the low power
portable market to the high performance base station market.
The part is provided in a 64-lead lead frame chip scale package
(LFCSP) that has a footprint of only 9 mm × 9 mm. Power
consumption can be optimized to suit the particular application
beyond just a speed grade option by incorporating power-down
controls, low power ADC modes, TxDAC power scaling, and a
half-duplex mode, which automatically disables the unused
digital path.
The AD9861 uses two 10-bit buses to transfer Rx path data and
Tx path data. These two buses support 20-bit parallel data
transfers or 10-bit interleaved data transfers. The bus is
configurable through either external mode pins or through
internal registers settings. The registers allow many more
options for configuring the entire device.
The differential input stage is dc self-biased and allows
differential or single-ended inputs. The output-staging block
aligns the data, carries out the error correction, and passes the
data to the output buffers.
The latency of the Rx path is about 5 clock cycles.
Rx Path Analog Input Equivalent Circuit
The Rx path analog inputs of the AD9861 incorporate a novel
structure that merges the function of the input sample-andhold amplifiers (SHAs) and the first pipeline residue amplifiers
into a single, compact switched capacitor circuit. This structure
achieves considerable noise and power savings over a conventional implementation that uses separate amplifiers by eliminating
one amplifier in the pipeline.
Figure 70 illustrates the equivalent analog inputs of the AD9861
(a switched capacitor input). Bringing CLK to logic high opens
switch S3 and closes switches S1 and S2; this is the sample mode
of the input circuit. The input source connected to VIN+ and
VIN− must charge capacitor CH during this time. Bringing CLK
to a logic low opens S2, and then switch S1 opens followed by
closing S3. This puts the input circuit into hold mode.
S1
CH
VIN+
+
CIN
RIN
S3
VCM
RIN
The following sections discuss the various blocks of the AD9861:
Rx block, Tx block, the auxiliary converters, the digital block,
programmable registers and the clock distribution block.
S2
CH
–
VIN–
CIN
03606-0-002
Figure 70. Differential Input Architecture
Rx PATH BLOCK
Rx Path General Description
The AD9861 Rx path consists of two 10-bit, 50 MSPS (for the
AD9861-50) or 80 MSPS (for the AD9861-80) analog-to-digital
converters (ADCs). The dual ADC paths share the same
clocking and reference circuitry to provide optimal matching
characteristics. Each of the ADCs consists of a 9-stage differential pipelined switched capacitor architecture with output error
correction logic.
The pipelined architecture permits the first stage to operate on a
new input sample, while the remaining stages operate on
preceding samples. Sampling occurs on the falling edge of the
input clock. Each stage of the pipeline, excluding the last,
consists of a low resolution flash ADC and a residual multiplier
to drive the next stage of the pipeline. The residual multiplier
uses the flash ADC output to control a switched capacitor
digital-to-analog converter (DAC) of the same resolution. The
DAC output is subtracted from the stage’s input signal, and the
residual is amplified (multiplied) to drive the next pipeline
stage. The residual multiplier stage is also called a multiplying
DAC (MDAC). One bit of redundancy is used in each one of
the stages to facilitate digital correction of flash errors. The last
stage simply consists of a flash ADC.
The structure of the input SHA places certain requirements on
the input drive source. The differential input resistors are
typically 2 kΩ each. The combination of the pin capacitance,
CIN, and the hold capacitance, CH, is typically less than 5 pF. The
input source must be able to charge or discharge this capacitance to 10-bit accuracy in one-half of a clock cycle. When the
SHA goes into sample mode, the input source must charge or
discharge capacitor CH from the voltage already stored on it to
the new voltage. In the worst case, a full-scale voltage step on
the input source must provide the charging current through the
RON of switch S1 (typically 100 Ω) to a settled voltage within
one-half of the ADC sample period. This situation corresponds
to driving a low input impedance. On the other hand, when the
source voltage equals the value previously stored on CH, the
hold capacitor requires no input current and the equivalent
input impedance is extremely high.
Rev. 0 | Page 22 of 52
AD9861
Rx Path Application Section
Adding series resistance between the output of the signal source
and the VIN pins reduces the drive requirements placed on the
signal source. Figure 71 shows this configuration.
default 1 V VREF reference accepts a 2 V p-p differential input
swing and the offset voltage should be
REFT = AVDD/2 + 0.5 V
REFB = AVDD/2 – 0.5 V
AD9861
AD9861
RSERIES
REFT
VIN+
0.1µF
CSHUNT
TO ADCs
VIN–
0.1µF
REFB
RSERIES
10µF
0.1µF
03606-0-003
VREF
Figure 71. Typical Input
The bandwidth of the particular application limits the size of
this resistor. For applications with signal bandwidths less than
10 MHz, the user may insert series input resistors and a shunt
capacitor to produce a low-pass filter for the input signal.
Additionally, adding a shunt capacitance between the VIN pins
can lower the ac load impedance. The value of this capacitance
depends on the source resistance and the required signal
bandwidth.
The Rx input pins are self-biased to provide this midsupply,
common-mode bias voltage, so it is recommended to ac couple
the signal to the inputs using dc blocking capacitors. In systems
that must use dc coupling, use an op amp to comply with the
input requirements of the AD9861. The inputs accept a signal
with a 2 V p-p differential input swing centered about one-half
of the supply voltage (AVDD/2). If the dc bias is supplied externally, the internal input bias circuit should be powered down by
writing to registers Rx_A dc bias [Register 0x3, Bit 6] and Rx_B
dc bias [Register 0x4, Bit 7].
The ADCs in the AD9861 are designed to sample differential
input signals. The differential input provides improved noise
immunity and better THD and SFDR performance for the Rx
path. In systems that use single-ended signals, these inputs can
be digitized, but it is recommended that a single-ended-todifferential conversion be performed. A single-ended-todifferential conversion can be performed by using a transformer
coupling circuit (typically for signals above 10 MHz) or by
using an operational amplifier, such as the AD8138 (typically
for signals below 10 MHz).
ADC Voltage References
The AD9861 10-bit ADCs use internal references that are
designed to provide for a 2 V p-p differential input range. The
internal band gap reference generates a stable 1 V reference level
and is decoupled through the VREF pin. REFT and REFB are
the differential references generated based on the voltage level
of VREF. Figure 72 shows the proper decoupling of the reference pins VREF, REFT, and REFB when using the internal
reference. Decoupling capacitors should be placed as close to
the reference pins as possible.
External references REFT and REFB are centered at AVDD/2
with a differential voltage equal to the voltage at VREF (by
default 1 V when using the internal reference), allowing a peakto-peak differential voltage swing of 2× VREF. For example, the
10µF
0.1µF
0.5V
03606-0-020
Figure 72. Typical Rx Path Decoupling
An external reference may be used for systems that require a
different input voltage range, high accuracy gain matching
between multiple devices, or improvements in temperature drift
and noise characteristics. When an external reference is desired,
the internal Rx band gap reference must be powered down
using the VREF2 register [Register 0x5, Bit 4] and the external
reference driving the voltage level on the VREF pin. The
external voltage level should be one-half of the desired peak-topeak differential voltage swing. The result is that the differential
voltage references are driven to new voltages:
REFT = AVDD/2 +VREF/2 V
REFB = AVDD/2 – VREF/2 V
If an external reference is used, it is recommended not to exceed
a differential offset voltage for the reference greater than 1 V.
Clock Input and Considerations
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals and, as a result, may be
sensitive to clock duty cycle. Commonly, a 5% tolerance is
required on the clock duty cycle to maintain dynamic performance characteristics. The AD9861 contains clock duty cycle
stabilizer circuitry (DCS). The DCS retimes the internal ADC
clock (nonsampling edge) and provides the ADC with a
nominal 50% duty cycle. Input clock rates of over 40 MHz can
use the DCS so that a wide range of input clock duty cycles can be
accommodated. Conversely, DCS should not be used for Rx
sampling below 40 MSPS. Maintaining a 50% duty cycle clock is
particularly important in high speed applications when proper
sample-and-hold times for the converter are required to
maintain high performance. The DCS can be enabled by writing
highs to the Rx_A/Rx_B CLK duty register bits [Register
0x06/0x07, Bit 4].
The duty cycle stabilizer uses a delay-locked loop to create the
nonsampling edge. As a result, any changes to the sampling
frequency require approximately 2 µs to 3 µs to allow the DLL
to adjust to the new rate and settle. High speed, high resolution
ADCs are sensitive to the quality of the clock input. The
Rev. 0 | Page 23 of 52
AD9861
degradation in SNR at a given full-scale input frequency (fINPUT),
due only to aperture jitter (tA), can be calculated with the
following equation:
SNR degradation = 20 log [(½)πFINtA)]
In the equation, the rms aperture jitter, tA, represents the rootsum-square of all jitter sources, which includes the clock input,
analog input signal, and ADC aperture jitter specification.
Undersampling applications are particularly sensitive to jitter.
The clock input is a digital signal that should be treated as an
analog signal with logic level threshold voltages, especially in
cases where aperture jitter may affect the dynamic range of the
AD9861. Power supplies for clock drivers should be separated
from the ADC output driver supplies to avoid modulating the
clock signal with digital noise. Low jitter crystal-controlled
oscillators make the best clock sources. If the clock is generated
from another type of source (by gating, dividing, or other methods), it should be retimed by the original clock at the last step.
Power Dissipation and Standby Mode
The power dissipation of the AD9861 Rx path is proportional to
its sampling rate. The Rx path portion of the digital (DRVDD)
power dissipation is determined primarily by the strength of the
digital drivers and the load on each output bit. The digital drive
current can be calculated by
Tx PATH BLOCK
The AD9861 transmit (Tx) path includes dual interpolating
10-bit current output DACs that can be operated independently
or can be coupled to form a complex spectrum in an image
reject transmit architecture. Each channel includes two FIR
filters, making the AD9861 capable of 1×, 2×, or 4× interpolation. High speed input and output data rates can be achieved
within the limitations of Table 9.
Table 9. AD9861 Tx Path Maximum Data Rate
Interpolation
Rate
1×
2×
4×
IDRVDD = VDRVDD × CLOAD × fCLOCK × N
where N is the number of bits changing and CLOAD is the average
load on the digital pins that changed.
The analog circuitry is optimally biased so that each speed
grade provides excellent performance while affording reduced
power consumption. Each speed grade dissipates a baseline
power at low sample rates, which increases with clock frequency.
The baseline power dissipation for either speed grade can be
reduced by asserting the ADC_LO_PWR pin, which reduces
internal ADC bias currents by half, in some case resulting in
degraded performance.
To further reduce power consumption of the ADC, the
ADC_LO_PWR pin can be combined with a serial programmable
register setting to configure an ultralow power mode. The
ultralow power mode reduces the power consumption by a
fourth of the normal power consumption. The ultralow power
mode can be used at slower sampling frequencies or if reduced
performance is acceptable. To configure the ultralow power
mode, assert the ADC_LO_PWR pin and write the following
register settings:
Register 0x08
Register 0x09
Register 0x0A
3, 4, and 5. Under this condition, the internal references are
powered down. When either or both of the channel paths are
enabled after a power-down, the wake-up time is directly related
to the recharging of the REFT and REFB decoupling capacitors
and the duration of the power-down. Typically, it takes approximately 5 ms to restore full operation with fully discharged 0.1 µF
and 10 µF decoupling capacitors on REFT and REFB.
(MSB) ‘0000 1100’
(MSB) ‘0111 0000’
(MSB) ‘0111 0000’
Either of the ADCs in the AD9861 Rx path can be placed in
standby mode independently by writing to the appropriate SPI
register bits in Registers 3, 4, and 5. The minimum standby
power is achieved when both channels are placed in full powerdown mode using the appropriate SPI register bits in Registers
20-Bit Interface
Mode
FD, HD10, Clone
HD20
FD, HD10, Clone
HD20
FD, HD10, Clone
HD20
Input Data
Rate per
Channel
(MSPS)
80
160
80
80
50
50
DAC
Sampling
Rate
(MSPS)
80
160
160
160
200
200
By using the dual DAC outputs to form a complex signal, an
external analog quadrature modulator, such as the Analog
Devices AD8349, can enable an image rejection architecture.
(Note: the AD9861 evaluation board includes a quadrature
modulator in the Tx path that accommodates the AD8345,
AD8346 and the AD8345 footprints.) To optimize the image
rejection capability, as well as LO feedthrough suppression in
this architecture, the AD9861 offers programmable (via the SPI
port) fine (trim) gain and offset adjustment for each DAC.
Also included in the AD9861 are a phase-locked loop (PLL)
clock multiplier and a 1.2 V band gap voltage reference. With
the PLL enabled, a clock applied to the CLKIN input is multiplied internally and generates all necessary internal synchronization
clocks. Each 10-bit DAC provides two complementary current
outputs whose full-scale currents can be determined from a
single external resistor.
An external pin, TxPWRDWN, can be used to power down the
Tx path, when not used, to optimize system power consumption.
Using the TxPWRDWN pin disables clocks and some analog
circuitry, saving both digital and analog power. The power-down
mode leaves the biases enabled to facilitate a quick recovery
time, typically <10 µs. Additionally, a sleep mode is available,
which turns off the DAC output current, but leaves all other
circuits active, for a modest power savings. An SPI compliant
serial port is used to program the many features of the AD9861.
Note that in power-down mode, the SPI port is still active.
Rev. 0 | Page 24 of 52
AD9861
DAC Equivalent Circuits
The AD9861 Tx path consisting of dual 10-bit DACs is shown
in Figure 73. The DACs integrate a high performance TxDAC
core, a programmable gain control through a programmable
gain amplifier (TxPGA), coarse gain control, and offset adjustment and fine gain control to compensate for system mismatches.
Coarse gain applies a gross scaling to either DAC by 1×, (1/2)×,
or (1/11)×. The TxPGA provides gain control from 0 dB to
–20 dB in steps of 0.1 dB and is controlled via the 8-bit TxPGA
setting. A fine gain adjustment of ±4% for each channel is controlled through a 6-bit fine gain register. By default, coarse gain
is 1×, the TxPGA is set to 0 dB, and the fine gain is set to 0%.
The TxDAC core of the AD9861 provides dual, differential,
complementary current outputs generated from the 10-bit data.
The 10-bit dual DACs support update rates up to 200 MSPS.
The differential outputs (IOUT+ and IOUT–) of each dual DAC
are complementary, meaning that they always add up to the fullscale current output of the DAC, IOUTFS. Optimum ac performance
loads or a transformer.
OFFSET
DAC
+
TxDAC
PGA
+
+
IOUT+B
+
+
IOUTFSMAX
REFIO
CURRENT
SOURCE ARRAY
FSADJ
0.1µF
IREF
RSET ≥ 4kΩ
03606-0-005
Figure 74. Reference Circuitry
Referring to the transfer function of the following equation,
IOUTFSMAX is the maximum current output of the DAC with the
default gain setting (0 dB), and is based on a reference current,
IREF. IREF is set by the internal 1.2 V reference and the external
RSET resistor.
IOUTFSMAX = 64 × (REFIO/RSET)
Typically, RSET is 4 kΩ, which sets IOUTFSMAX to 20 mA, the
optimal dynamic setting for the TxDACs. Increasing RSET by a
factor of 2 proportionally decreases IOUTFSMAX by a factor of 2.
IOUTFSMAX of each DAC can be rescaled either simultaneously
using the TxPGA gain register or independently using the
DAC A/DAC B coarse gain registers.
The TxPGA function provides 20 dB of simultaneous gain
range for both DACs, and is controlled by writing to the SPI
register TxPGA gain for a programmable full-scale output of
10% to 100% of IOUTFSMAX. The gain curve is linear in dB, with
steps of about 0.1 dB. Internally, the gain is controlled by
changing the main DAC bias currents with an internal TxPGA
DAC whose output is heavily filtered via an on-chip R-C filter
to provide continuous gain transitions. Note that the settling
time and bandwidth of the TxPGA DAC can be improved by a
factor of 2 by writing to the TxPGA fast register.
IOUT–A
REFERENCE
BIAS
PGA
DAC A AND DAC B
REFERENCE BIASES
IOUT+A
+
+
TxDAC
1.2V
REFERENCE
IOUT–B
+
OFFSET
DAC
03606-0-004
Figure 73. TxDAC Output Structure Block Diagram
The fine gain control provides improved balance of QAM
modulated signals, resulting in improved modulation accuracy
and image rejection.
The independent DAC A and DAC B offset control adds a small
dc current to either IOUT+ or IOUT– (not both). The selection
of which IOUT this offset current is directed toward is
programmable via register setting. Offset control can be used
for suppression of an LO leakage signal that typically results at
the output of the modulator. If the AD9861 is dc-coupled to an
external modulator, this feature can be used to cancel the output
offset on the AD9861 as well as the input offset on the modulator.
The reference circuitry is shown in Figure 74.
Each DAC has independent coarse gain control. Coarse gain
control can be used to accommodate different IOUTFS from the
dual DACs. The coarse full-scale output control can be adjusted
by using the DAC A/DAC B coarse gain registers to 1/2 or 1/11
of the nominal full-scale current.
Fine gain controls and dc offset controls can be used to
compensate for mismatches (for system level calibration),
allowing improved matching characteristics of the two Tx
channels and aiding in suppressing LO feedthrough. This is
especially useful in image rejection architectures. The 10-bit dc
offset control of each DAC can be used independently to
provide an offset of up to ±12% of IOUTFSMAX to either differential
pin, thus allowing calibration of any system offsets. The fine
gain control with 5-bit resolution allows the IOUTFSMAX of each
DAC to be varied over a ±4% range, allowing compensation of
any DAC or system gain mismatches. Fine gain control is set
through the DAC A/DAC B fine gain registers, and the offset
control of each DAC is accomplished using the DAC A/DAC B
offset registers.
Rev. 0 | Page 25 of 52
AD9861
Clock Input Configuration
The quality of the clock and data input signals is important in
achieving optimum performance. The external clock driver
circuitry provides the AD9861 with a low jitter clock input that
meets the min/max logic levels while providing fast edges.
When a driver is used to buffer the clock input, it should be
placed very close to the AD9861 clock input, thereby negating
any transmission line effects such as reflections due to
mismatch.
Programmable PLL
The sleep mode, when activated, turns off the DAC output
currents, but the rest of the chip remains functioning. When
coming out of sleep mode, the AD9861 immediately returns to
full operation.
A full power-down mode can be enabled through the SPI
register, which turns off all Tx path related analog and digital
circuitry in the AD9861. When returning from full power-down
mode, enough clock cycles must be allowed to flush the digital
filters of random data acquired during the power-down cycle.
Interpolation Stage
CLKIN can function either as an input data rate clock (PLL
enabled) or as a DAC data rate clock (PLL disabled).
Interpolation filters are available for use in the AD9861 transmit
path, providing 1× (bypassed), 2×, or 4× interpolation.
The PLL clock multiplier and distribution circuitry produce the
necessary internal timing to synchronize the rising edge triggered latches for the enabled interpolation filters and DACs.
This circuitry consists of a phase detector, charge pump, voltage
controlled oscillator (VCO), and clock distribution block, all
under SPI port control. The charge pump, phase detector, and
VCO are powered from PLL_AVDD, while the clock distribution circuits are powered from the DVDD supply.
To ensure optimum phase noise performance from the PLL
clock multiplier circuits, PLL_AVDD should originate from a
clean analog supply. The speed of the VCO within the PLL also
has an effect on phase noise.
The PLL locks with VCO speeds as low as 32 MHz up to
350 MHz, but optimal phase noise with respect to VCO speed is
achieved by running it in the range of 64 MHz to 200 MHz.
Power Dissipation
The interpolation filters effectively increase the Tx data rate
while suppressing the original images. The interpolation filters
digitally shift the worst-case image further away from the
desired signal, thus reducing the requirements on the analog
output reconstruction filter.
There are two 2× interpolation filters available in the Tx path.
An interpolation rate of 4× is achieved using both interpolation
filters; an interpolation rate of 2× is achieved by enabling only
the first 2× interpolation filter.
The first interpolation filter provides 2× interpolation using a
39-tap filter. It suppresses out-of-band signals by 60 dB or more
and has a flat pass-band response (less than 0.1 dB ripple)
extending to 38% of the input Tx data rate (19% of the DAC
update rate, fDAC). The maximum input data rate is 80 MSPS per
channel when using 2× interpolation.
The AD9861 Tx path power is derived from three voltage
supplies: AVDD, DVDD, and DRVDD.
The second interpolation filter provides an additional 2× interpolation for an overall 4× interpolation. The second filter is a 15-tap
filter, which suppresses out-of-band signals by 60 dB or more.
IDRVDD and IDVDD are very dependent on the input data
rate, the interpolation rate, and the activation of the internal
digital modulator. IAVDD has the same type of sensitivity to
data, interpolation rate, and the modulator function, but to a
much lesser degree (< 10%).
The flat pass-band response (less than 0.1 dB attenuation) is
38% of the Tx input data rate (9.5% of fDAC). The maximum
input data rate per channel is 50 MSPS per channel when using
4× interpolation.
Sleep/Power-Down Modes
Latch/Demultiplexer
The AD9861 provides multiple methods for programming
power saving modes. The externally controlled TxPWRDWN
or SPI programmed sleep mode and full power-down mode are
the main options.
Data for the dual-channel Tx path can be latched in parallel
through two ports in half-duplex operations (HD20 mode) or
through a single port by interleaving the data (FD, HD10, and
Clone modes). See the Flexible I/O Interface Options section in
the Digital Block description and the Clock Distribution Block
section for further descriptions of each mode.
TxPWRDWN is used to disable all clocks and much of the
analog circuitry in the Tx path when asserted. In this mode, the
biases remain active, therefore reducing the time required for
re-enabling the Tx path. The time of recovery from powerdown for this mode is typically less than 10 µs.
Rev. 0 | Page 26 of 52
AD9861
AUXILIARY CONVERTERS
The AD9861 contains auxiliary analog-to-digital converters
(AuxADCs) and auxiliary digital-to-analog converters
(AuxDACs). These auxiliary converters can be used to measure
or force system-wide control signals.
By default, the auxiliary converters are disabled and powered
down. Enabling and controlling the auxiliary converters is
achieved through the serial programmable registers.
Pins 29, 30, and 46 are configurable either as AuxDAC outputs
or as AuxADC inputs. The respective AuxADC inputs are
connected to the external pin when a conversion is initiated and
are disconnected when the conversion is complete. The
AuxDAC outputs are enabled by writing to the respective
power-up registers in Register 0x29.
•
Pin 29 can be connected to AuxDAC_A and/or
AuxADC_A Channel 2.
•
Pin 30 can be connected to AuxDAC_B and/or
AuxADC_A Channel 1.
•
Pin 46 can be connected to AuxDAC_C and/or
AuxADC_B.
Update C, B, and A]. Slave mode is enabled by writing a high to
the slave mode register bit [Register 0x28, Bit 7, Slave Enable].
Another synchronization mode allows any combination of
AuxDACs to be updated along with an externally applied rising
edge to the TxPwrDwn pin.
Typical settling time for the AuxDAC output is less than 0.5 µs,
but is dependent on the load.
Auxiliary ADCs
Two auxiliary 10-bit SAR analog-to-digital converters
(AuxADCs) are available for monitoring various external
signals throughout the system, such as a receive signal strength
indicator (RSSI) function or temperature indicator. The
AuxADCs have many SPI programmable options. Register
settings can be used to configure various full-scale reference
options, change the sampling rate, and average multiple sample
readings. By default, the AuxADC start conversion and output
value is accessed through the register map. Additionally an
auxiliary serial port can be enabled and used to initiate a
conversion and read back the AuxADC data. The auxiliary
serial port interface is available so that the normal SPI can be
used to program other options while the AuxADC is accessed.
By default, the AuxADCs are powered down and automatically
powered up when a conversion is initiated.
Auxiliary DACs
The AD9861 integrates three 8-bit voltage output auxiliary
digital-to-analog converters (AuxDACs), which can be used for
supplying various control voltages throughout the system such
as a VCXO voltage control or external VGA gain control. The
AuxDACs have a programmable full-scale output voltage, VOUTFS,
and can be synchronized to update with a single register write
or a rising edge on the TxPwrDwn pin.
By default, the AuxDAC outputs are powered down and require
a serial write to the power-up registers [Register 0x29, Bits 2–0]
to enable them.
The full-scale output of each AuxDAC is independently
programmable to the full scales of 2.5 V, 2.7 V, 3.0 V, or 3.3 V by
using Serial Register 0x17. The AuxDAC outputs have an I-to-V
driver that produces a voltage output that settles to ±1 LSB
within 0.5 µs. The output driver is capable of sinking or sourcing
up to 6 mA. Using the AuxDAC requires the SPI to be operational.
The AuxDACs are based on a resistor divider network. The
AuxDACs output level is proportional to the straight binary
input codes from the appropriate SPI registers, Registers 0x24
to 0x26. By default, the AuxDAC output is updated immediately
following the register write, but the update can occur
synchronously to a single register write or to the TxPwrDwn
rising edge.
In slave mode, the AuxDAC update occurs when a logic high is
written to the appropriate update registers [Register 0x28, Bits 2–0,
The two AuxADCs (AuxADC_A and AuxADC_B) can
monitor up to three system signals. AuxADC_A has multiplexed inputs that control whether pin AUX_ADC_A1 or pin
AUX_ADC_A2 is connected to the input of AuxADC_A. The
multiplexer is programmed through Register 0x22, Bit 1,
SelectA. By default, the register is low, which connects the
AUX_ADC_A2 pin to the input.
The full-scale AuxADC reference can be generated from the
analog supply (supply dependent), an internal reference, or
from an external applied reference. Table 10 shows the register
settings required to select the AuxADC full-scale reference.
By default, an internal reference provides a buffered full-scale
reference for both of the AuxADCs, which is equal to the
supply voltage for the AuxADCs (PLL_AVDD). A supply
independent 2.5 V or 3.0 V internal full-scale reference can be
enabled by writing to register AuxADC Ref Enable and
AuxADC Ref FS in Register 0x17. This internal reference is
based on the main Rx path ADC VREF voltage, so it requires
the main Rx path VREF to be enabled.
Another AuxADC full-scale reference option is an externally
supplied full-scale reference. The external reference can be
applied to either or both of the AuxADCs by setting the
appropriate bit(s) in Registers 0x22 and 0x17. Setting either or
both of these bits high disconnects the internal reference buffer
and enables the externally applied reference from the
AuxADC_Ref pin to the respective channel(s).
Rev. 0 | Page 27 of 52
AD9861
Table 10. Configuring AuxADC Reference
AuxADC_A Reference
Configuration
Buffered PLL_VDD
Internal 3.0 V (3 x VREF)
AuxADC Ref Enable
[Register 0x17, Bit 1]
0
1
AuxADC Ref FS
[Register 0x17, Bit 0]
0
0
Refsel A/B
[Register 0x22,
Bit 2/Bit 5]
0
1
Internal 2.5 V (2.5 x VREF)
Externally forced
1
0
1
Don't Care
1
1
The AuxADCs can convert at rates of up to 5.33 MSPS
(0.1875 µs maximum conversion time) and have a bandwidth
of around 200 kHz. The conversion time, including setup,
requires 12 clock cycles. The maximum clock rate for the
AuxADCs is 64 MHz and is generated from a divided down Rx
ADC clock. The divide down ratio is controlled by register
AuxADC Clock Div [Register 0x23, Bits 1, 0]. By default, the Rx
ADC clock is divided by 4. At an Rx ADC rate greater than 64
MHz, the AuxADC Clock Div register must be set to divide-by2 or divide-by-4.
On-chip averaging of 2, 4, 8, 16, 32, or 64 samples can be
enabled through Register 0x18 for AuxADC_A or through
Register 0x19 for AuxADC_B. When the averaging option is
enabled, the AuxADC continually converts the number of
samples specified and outputs the average value.
There are three modes of operating the AuxADC: SPI operation
mode (default), SPI with external start convert operation mode,
and Aux_SPI operation mode.
In the default SPI operation mode, a conversion is initiated by
writing a logic high to one or both of the start register bits,
Start A or Start B [Register 0x22, Bit 0 or Bit 3]. If AuxADC is
configured as averaging mode, the proper start bit is the Start
Average AuxADC A/B register [Register 0x18, Bit 7/Register
0x19, Bit 7].
When the conversion is complete, the straight binary, 10-bit
output data of the AuxADC is written to one of three reserved
locations in the register map, depending on which AuxADC
and which multiplexed input is selected. Because the AuxADCs
output 10 bits, two register addresses are needed for each data
location.
In the optional SPI with external start convert operation mode,
the conversion is initiated by asserting AuxSPI_csb, and data
retrieval is accomplished through the SPI interface (data
retrieval is similar to the default operation). The AuxSPI_csb
can be configured to initiate the conversion of either one of the
AuxADCs. This mode is configured by setting the AuxSPI
enable register bit [Register 0x22, Bit 7].
Notes
Default mode.
Decouple at AUXADC_REF pin.
VREF voltage from Rx path.
Decouple at AUXADC_REF pin.
Force and decouple at
AUXADC_REF pin.
AuxADCs and is available so that the SPI is not continually
busy retrieving AuxADC data.
The AuxSPI can be enabled and configured by setting register
AuxSPI enable [Register 0x22, Bit 7]. Also required is that the
normal serial port interface be configured for 3-wire mode (the
SPI_SDO pin must be disabled to use the Aux_SPI_SDO pin)
by setting the SDIO BiDir register bit [Register 0x00, Bit 7].
Register bit Sel BnotA [Register 0x22, Bit 6] configures whether
AuxADC_A or AuxADC_B is controlled by the AuxSPI.
AuxADC_A has two inputs: AuxADC_A1 and AuxADC_A2.
Setting the Select A bit [Register 0x22, Bit 1] determines which
of the multiplexed inputs is connected to AuxADC_A.
The AuxSPI consists of a chip select pin (AUX_SPI_CS, pin
number 4), a clock pin (AUX_SPI_CLK), and a data output pin
(AUX_SPI_SDO multiplex with the SPI_SDO pin). A conversion
is initiated by pulsing the AUX_SPI_CS pin low (AUX_SPI_CS
should remain low during the entire conversion cycle, including
the readback phase). When the conversion is complete, the data
pin, AUX_SPI_SDO, transitions from a logic low to a logic
high. At this point, the user supplies an external clock on the
AUX_SPI_CLK pin. The AUX_SPI_CLK pin should be tied
low when not in use. No data is present on the first rising edge.
The data output bit is updated on the falling edge of the clock
pulse and is settled by and can be latched on the next clock
rising edge. The data arrives serially, MSB first. The AuxSPI
runs at a rate up to 16 MHz.
Operation of the Aux_SPI requires that 3-wire SPI mode be
used, disabling the SDO pin. If the controller is a 4-wire
interface, a method of connecting the 3-wire AD9861 interface
to the 4-wire controller is suggested in Figure 75.
An example of an AuxSPI access is shown in Figure 75. In the
AuxSPI configuration, a start convert is initiated by applying a
rising edge to the Aux_SPI_CS pin. A rising edge on the
Aux_SPI_DO pin indicates that a conversion is done. Supplying
a clock to the Aux_SPI_CLK then outputs data on the
Aux_SPI_DO pin, MSB first.
An optional auxiliary serial port interface (AuxSPI) can be used
to access an AuxADC. The AuxSPI can initiate an AuxADC
conversion and can be used to retrieve the data. The AuxSPI
can be configured to allow dedicated control of one of the
Rev. 0 | Page 28 of 52
CONTROLLER
SPI_CS[x]
SPI_CLK
AD986x
SPI_CS
SPI_CLK
SPI_SDIO
SPI_DI
03606-0-006
Figure 75. Diagram to Connect 3-Wire SPI to a 4-Wire SPI Controller
AD9861
Figure 76 shows a timing diagram of the AuxSPI when it is used to control and access an AuxADC.
Figure 77 shows the timing for each of the three AuxADC modes of operation.
1 2 3
AUXSPI_CS
AUXSPI_CLK
D9 D8
AUXSPI_SDO
D0
1. AUXADC CONVERSION START SIGNAL
2. AUXADC CONVERSION DONE
3. AUXADC OUTPUT UDATE (MSB)
03606-0-021
Figure 76. Timing Diagram of AuxSPI
tCONVERSION = tC
NORMAL SPI READOUT
16 SPI CLK
16 SPI CLK
16 SPI CLKs USED TO CONFIGURE AND
INITIATE A START CONVERSION
16 SPI CLKs USED TO READ BACK
8 REGISTER BITS
EXTERNAL START COVERT BIT AND
SPI READOUT MODE
EXTERNAL PIN USED TO INITIATE A
START CONVERSION
16 SPI CLKs USED TO READ BACK
8 REGISTER BITS
READOUT MODE WITH AUXILIARY SPI
EXTERNAL PIN USED TO INITIATE A
START CONVERSION
8-BIT SERIAL
OUTPUT
READOUT MODE WITH
AUXILIARY SPI
CYCLE TIME = tC + 8 SPI CLK
EXTERNAL START COVERT BIT AND
SPI READOUT MODE
CYCLE TIME = tC + 16 SPI CLK
NORMAL SPI READOUT
CYCLE TIME = 16 SPI CLK + tC + 16 SPI CLK
03606-0-007
Figure 77. AuxADC Data Cycle Times for Various Readout Methods
Rev. 0 | Page 29 of 52
AD9861
DIGITAL BLOCK
Flexible I/O Interface Options
The AD9861 digital block allows the device to be configured in
various timing and operation modes. The following sections
discuss the flexible I/O interfaces, the clock distribution block,
and the programming of the device through mode pins or SPI
registers.
The AD9861 can accommodate various data interface transfer
options (flexible I/O). The AD9861 uses two 10-bit buses, an
upper bus (U10) and a lower bus (L10), to transfer the dualchannel 10-bit ADC data and dual-channel 10-bit DAC data by
means of interleaved data, parallel data, or a mix of both. Table 11
shows the different I/O configurations of the modes depending
on half-duplex or full-duplex operation. Table 12 and Table 13
summarize the pin configurations versus the modes.
Table 11. Flexible Data Interface Modes
Mode
Name
HD20
Tx Only Mode (Half-Duplex)
Rx Only Mode (Half-Duplex)
AD9861
AD9861
U[0:9]
L[0:9]
IFACE1
IFACE2
IFACE3
Tx_A DATA
L[0:9]
Tx_B DATA
Tx/Rx
OUTPUT CLOCK
DIGITAL
BACK
END
OUTPUT CLOCK
U[0:9]
IFACE1
IFACE2
IFACE3
Rx_A DATA
Rx_B DATA
Tx/Rx
OUTPUT CLOCK
AD9861
U[0:9]
L[9]
IFACE1
IFACE2
IFACE3
AD9861
Tx_A/B DATA
U[9]
TxSYNC
Tx/Rx
OUTPUT CLOCK
DIGITAL
BACK
END
OUTPUT CLOCK
L[0:9]
IFACE1
IFACE2
IFACE3
AD9861
U[0:9]
RxSYNC
Rx_A/B DATA
Tx/Rx
OUTPUT CLOCK
IFACE2
IFACE3
TxSYNC
03606-0-013
OUTPUT CLOCK
AD9861
U[0:9]
DIGITAL
BACK
END
OUTPUT CLOCK
L[0:9]
U[0:9]
Rx_A/B DATA
IFACE1
IFACE2
IFACE3
AD9861
U[0:9]
L[9]
IFACE1
IFACE2
IFACE3
N/A
OUTPUT CLOCK
OUTPUT CLOCK
DIGITAL
BACK
END
OUTPUT CLOCK
03606-0-010
Clone
DIGITAL
BACK
END
AD9861
Tx_A/B DATA
L[0:9]
IFACE1
N/A
03606-0-012
03606-0-009
FD
DIGITAL
BACK
END
OUTPUT CLOCK
03606-0-008
HD10
Concurrent Tx + Rx Mode
(Full-Duplex)
L[0:9]
IFACE1
IFACE2
IFACE3
Tx_A/B DATA
Rx_A/B DATA
TxSYNC
OUTPUT CLOCK
OUTPUT CLOCK
03606-0-014
03606-0-016
AD9861
Tx_A/B DATA
U[0:9]
TxSYNC
Tx/Rx
OUTPUT CLOCK
DIGITAL
BACK
END
OUTPUT CLOCK
L[0:9]
IFACE1
IFACE2
IFACE3
03606-0-011
Rx_A DATA
Rx_B DATA
Tx/Rx
OUTPUT CLOCK
DIGITAL
BACK
END
N/A
OUTPUT CLOCK
03606-0-015
Rev. 0 | Page 30 of 52
DIGITAL
BACK
END
General Notes
Rx Data Rate
= 1 × ADC Sample Rate
Two 10-Bit Parallel Rx Data
Buses
Tx Data Rate
= 1 × ADC Sample Rate
Two 10-Bit Parallel Tx Data
Buses
Rx Data Rate
= 2 × ADC Sample Rate
One 10-Bit Interleaved Rx
Data Bus
Tx Data Rate
= 2 × ADC Sample Rate
One 10-Bit Interleaved Tx
Data Bus
Rx Data Rate
= 2 × ADC Sample Rate
One 10-Bit Interleaved Rx
Data Bus
Tx Data Rate
= 2 × ADC Sample Rate
One 10-Bit Interleaved Tx
Data Bus
Rx Data Rate
= 1 × ADC Sample Rate
Two 10-Bit Parallel Rx Data
Buses
Tx Data Rate
= 2 × ADC Sample Rate
One 10-Bit Interleaved Tx
Data Bus
Requires SPI Interface to
Configure; Similar to AD9860
Data Interface
AD9861
Table 12 describes AD9861 pin function (when mode pins are used) relative to I/O mode, and for half-duplex modes whether
transmitting or receiving.
Table 12. AD9861 Pin Function vs. Interface Mode (No SPI Cases)
Mode Name
FD
HD10
(Tx/Rx = High)
HD10
(Tx/Rx = Low)
HD20
(Tx/Rx = High)
HD20
(Tx/Rx = Low)
Clone Mode
(Tx/Rx = High)
Clone Mode
(Tx/Rx = Low)
U10
Interleaved Tx Data
Interleaved Tx Data
IFACE1
TxSYNC
Tx/Rx = Tied High
IFACE2
Buffered Rx Clock
10/20 Pin Control Tied High
IFACE3
Buffered Tx Clock
Buffered Tx Clock
MSB = RxSYNC
Others = Three-state
Tx_A Data
L10
Interleaved Rx Data
MSB = TxSYNC
Others = Three-state
Interleaved Rx Data
Tx/Rx = Tied Low
10/20 Pin Control Tied High
Buffered Rx Clock
Tx_B Data
Tx/Rx = Tied High
10/20 Pin Control Tied Low
Buffered Tx Clock
Rx_B Data
Rx_A Data
Tx/Rx = Tied Low
10/20 Pin Control Tied Low
Buffered Rx Clock
Clone mode not available without SPI.
Clone mode not available without SPI.
Table 13 describes AD9861 pin function (when SPI programming is used) relative to flexible I/O mode, and for half-duplex modes
whether transmitting or receiving.
Table 13. AD9861 Pin Function vs. Interface Mode (Configured through the SPI Registers)
Mode Name
FD
U10
Interleaved Tx Data
L10
Interleaved Rx Data
IFACE1
TxSYNC
HD10, Tx Mode
(Tx/Rx = High)
Interleaved Tx Data
MSB = TxSYNC
Others = Three-state
Tx/Rx = Tied High
HD10, Rx Mode
(Tx/Rx = Low)
MSB = RxSYNC
Other = Three-state
Interleaved Tx Data
Tx/Rx = Tied Low
Optional Buffered
System Clock
Buffered Rx Clock
HD20, Tx Mode
(Tx/Rx = High)
Tx_A Data
Tx_B Data
Tx/Rx = Tied High
Optional Buffered
System Clock
Buffered Tx Clock
HD20, Rx Mode
(Tx/Rx = Low)
Rx_B Data
Rx_A Data
Tx/Rx = Tied Low
Optional Buffered
System Clock
Buffered Rx Clock
Clone Mode ,
Tx Mode
(Tx/Rx = High)
Clone Mode ,
Rx Mode
(Tx/Rx = Low)
Interleaved Tx Data
MSB = TxSYNC
Others = Three-state
Tx/Rx = Tied High
Optional Buffered
System Clock
Buffered Tx Clock
Rx_B Data
Rx_A Data
Tx/Rx = Tied Low
Optional Buffered
System Clock
Buffered Rx Clock
Summary of Flexible I/O Modes
IFACE2
Buffered System
Clock
Optional Buffered
System Clock
IFACE3
Buffered Tx Clock
Buffered Tx Clock
The following notes provide a general description of the FD
mode configuration. For more information, refer to Table 16.
FD Mode
The full-duplex (FD) mode can be configured by using mode
pins or with SPI programming. Using the SPI allows additional
configuration flexibility of the device.
FD mode is the only mode that supports full-duplex, receive,
and transmit concurrent operation. The upper 10-bit bus (U10)
is used to accept interleaved Tx data, and the lower 10-bit bus
(L10) is used to output interleaved Rx data. Either the Rx path
or the Tx path (or both) can be independently powered down
using either (or both) the RxPwrDwn and TxPwrDwn pins. FD
mode requires interpolation of 2× or 4×.
Note the following about the Tx path in FD mode:
•
Interpolation rate of 2× or 4× can be programmed with
mode pins or SPI.
•
Max DAC update rate = 200 MSPS.
Max Tx input data rate = 80 MSPS/channel (160 MSPS
interleaved).
•
TxSYNC is used to direct Tx input data.
TxSYNC = high indicates channel Tx_A data.
TxSYNC = low indicates channel Tx_B data.
Rev. 0 | Page 31 of 52
AD9861
•
•
Max ADC sampling rate = 50 MSPS (AD9861-50) or
80 MSPS (AD9861-80).
Note the following about the Rx path in FD mode:
•
Output data rate = 2× ADC sample rate.
•
•
Interleaved Rx data output from L10 bus.
•
Rx_A output when IFACE2 (or RxSYNC) logic level = low.
Rx_B output when IFACE2 (or RxSYNC) logic level = high.
•
Buffered Tx clock output (from IFACE3 pin) equals 2× the
DAC update rate; one rising edge per interleaved Tx sample.
ADC CLK Div register can be used to divide down the
clock driving the ADC, which accepts up to 50 MHz
(AD9861-50) or up to 80 MHz (AD9861-80).
Max ADC sampling rate = 50 MSPS (AD9861-50) or
80 MSPS (AD9861-80).
HD20 Mode
•
The Rx path output data rate is 2× the ADC sample rate
(interleaved).
•
Rx_A output when IFACE2 logic level = low.
Rx_B output when IFACE2 logic level = high.
HD10 Mode
The half-duplex, 10-bit interleaved outputs mode, HD10 can be
configured using mode pins or the SPI.
HD10 mode supports half-duplex only operations and can
interface to a single 10-bit data bus with independent Rx and Tx
synchronization pins (RxSYNC and TxSYNC). Both the U10
and L10 buses are used on the AD9861, but the logic level of the
Tx/Rx selector (controlled through IFACE1 pin) is used to
disable and three-state the unused bus, allowing U10 and L10 to
be tied together. The MSB of the unused bus acts as the RxSYNC
(during Rx operation) or TxSYNC (during Tx operation). A
single pin is used to output the clocks for Rx and Tx data
latching (from the IFACE3 pin) switching, depending on which
path is enabled. HD10 mode requires interpolation of 2× or 4×.
The following notes provide a general description of the HD10
mode configuration. For more information, refer to Table 16.
The half-duplex 20-bit parallel output, HD20, can be configured
using mode pins or through SPI programming.
HD20 mode supports half-duplex only operations and can
interface to a single 20-bit data bus (two parallel 10-bit buses).
Both the U10 and L10 buses are used on the AD9861. The logic
level of the Tx/Rx selector (controlled through IFACE1 pin) is
used to configure the buses as Rx outputs (during Rx operation)
or as Tx inputs (during Tx operation). A single pin is used to
output the clocks for Rx and Tx data latching (from the IFACE3
pin) switching, depending on which path is enabled.
The following notes provide a general description of the HD20
mode configuration. For more information, refer to Table 16.
Note the following about the Tx Path in HD20 mode:
•
Interpolation rate of 1×, 2×, or 4× can be programmed with
mode pins or SPI.
•
Max DAC update rate = 200 MSPS.
Max Tx input data rate = 160 MSPS/channel with bypassed
interpolation filters, 100 MSPS for 2× interpolation or
50 MSPS for 4× interpolation.
•
Tx_A DAC data is accepted from the U10 bus; Tx_B DAC
data is accepted from the L10 bus.
Note the following about the Tx path in HD10 mode:
Note the following about the Rx path in HD20 mode:
•
Interpolation rate of 2× or 4× can be programmed with
mode pins or SPI.
•
Interleaved Tx data accepted on U10 bus, L10 bus MSB acts
as TxSYNC.
•
Max DAC update rate = 200 MSPS.
Max Tx input data rate = 80 MSPS/channel (160 MSPS
interleaved).
•
TxSYNC is used to direct Tx input data.
TxSYNC = high indicates channel Tx_A data.
TxSYNC = low indicates channel Tx_B data.
Note the following about the Rx path in HD10 mode:
•
ADC CLK Div register can be used to divide down the
clock driving the ADC, which accepts up to 50 MHz
(AD9861-50) or up to 80 MHz (AD9861-80).
•
ADC CLK Div register can be used to divide down the
clock driving the ADC, which accepts up to 50 MHz
(AD9861-50) or up to 80 MHz (AD9861-80).
•
Max ADC sampling rate = 50 MSPS (AD9861-50) or
80 MSPS (AD9861-80).
•
The Rx_A output data is output on L10 bus; the Rx_B
output data is output on U10 bus.
Clone Mode
An interface mode provides a similar interface to the AD9860
when used in half-duplex mode. This mode is referred to as
clone mode and requires SPI to configure.
Clone mode provides a parallel Rx data output (20 bits) while in
Rx mode, and accepts interleaved Tx data (10-bit) while in Tx
Rev. 0 | Page 32 of 52
AD9861
mode. Both the U10 and L10 buses are used on the AD9861.
The logic level of the Tx/Rx selector (controlled through the
IFACE1 pin) is used to configure the buses for Rx outputs
(during Rx operation) or as Tx inputs (during Tx operation). A
single pin is used to output the clocks for Rx and Tx data
latching (from the IFACE3 pin), depending on which path is
enabled. Clone mode requires interpolation of 2× or 4×.
•
Max ADC sampling rate = 50 MSPS (AD9861-50) or
80 MSPS (AD9861-80).
•
Output data rate = ADC sample rate, that is, two 10-bit
parallel outputs per one buffer Rx clock output cycle.
•
The Rx_A output data is output on L10 bus; the Rx_B
output data is output on U10 bus.
The following notes provide a general description of the clone
mode configuration. For more information, refer to Table 16.
Configuring with Mode Pins
Note the following about the Tx path in clone mode:
•
Interpolation rate of 2× or 4× can be programmed with
mode pins or SPI.
•
Max DAC update rate = 200 MSPS.
Max Tx input data rate = 80 MSPS/channel (160 MSPS
interleaved).
•
TxSYNC is used to direct Tx input data.
TxSYNC = high indicates channel Tx_A data.
TxSYNC = low indicates channel Tx_B data.
•
Buffered Tx clock output (from IFACE3 pin) uses one
rising edge per interleaved Tx sample.
Note the following about the Rx path in clone mode:
•
The flexible interface can be configured with or without the SPI,
although more options and flexibility are available when using
the SPI to program the AD9861. Mode pins can be used to
power down sections of the device, reduce overall power consumption, configure the flexible I/O interface, and program the
interpolation setting. The SPI register map, which provides
many more options, is discussed in the Configuring with SPI
section.
Mode Pins/Power-Up Configuration Options
Various options are configurable at power-up through mode
pins, and also through control pins for power-down modes. The
logic value of the configuration mode pins are latched when the
device is brought out of reset (rising edge of RESET). The mode
pin names and their functions are shown in Table 14. Table 15
provides a detailed description of the mode pins.
ADC CLK Div register can be used to divide down the
clock driving the ADC, which accepts up to 50 MHz
(AD9861-50) or up to 80 MHz (AD9851-80).
Table 14. Mode Pin Names and Functions
Pin Name
RxPwrDwn
Duration
Permanent
TxPwrDwn
Permanent
Tx/Rx (IFACE1)
Permanent only for
HD Flex I/O interface
ADC_LO_PWR
Defined at Reset or
Power-Up
Defined at Reset or
Power-Up
SPI_Bus_Enable
(SPI_CS)
FD/HD
10/20 only valid for
HD mode
Interp0 and Interp1
Defined at Reset or
Power-Up
Defined at Reset or
Power-Up
Defined at Reset or
Power-Up
Function
When high, digital clocks to Rx block are disabled. Analog circuitry that require <10 µs to
power up are powered off.
When high, digital clocks to Tx block are disabled (PLL remains powered to maintain
output clock with an optional SPI shut off). Analog circuitry that require <10 µs to power
up are powered off.
When high, digital clocks to Tx block are disabled (PLL remains powered to maintain
output clock with an optional SPI shutoff). Tx analog blocks remain powered up unless
Tx_PwrDwn is asserted.
When low, digital clocks to Rx block are disabled. Rx analog circuitry remain powered up
unless Rx_PwrDwn is asserted.
When enabled, this bit scales the ADC power-down by 40%.
This function is controlled through the SPI_CS pin. This pin must remain low to maintain
mode pin functionality (the SPI port remains nonfunctional). This pin must be high when
coming out of reset to enable the SPI.
Configures the flex I/O for FD or HD mode. This control applies only if the SPI bus is
disabled.
If the flex I/O bus is in HD mode, this bit is used to configure parallel or interleaved data
mode. This control applies only if the SPI bus is disabled.
The Interp1 and Interp0 bits configure the PLL and the interpolation rate to 1× [00], 2×
[01], or 4× [10]. This control applies only if the SPI bus is disabled.
Rev. 0 | Page 33 of 52
AD9861
Table 15. Mode Pin Names and Descriptions
Pin Name
ADC_LO_PWR
FD/HD (SDO)
10/ 20
SPI_Bus_Enable (SPI_CS)
Interp0 and Interp1
RxPwrDwn
TxPwrDwn
Tx/Rx
Description
ADC Low Power Mode Option. ADC_LO_PWR is latched during the rising edge of RESET.
Logic low results in ADC operation at nominal power mode.
Logic high results in ADC consuming 40% less power than the nominal power mode.
For Flex I/O Configuration, this control applies only if the SPI bus is disabled. FD/HD (SDO) is latched during the
rising edge of RESET.
Logic low identifies that the DUT flex I/O port will be configured for half-duplex operation.
10/20 (IFACE2) is also latched during the rising edge of RESET to identify interleaved data mode or parallel data
modes.
Logic low indicates that the flex I/O will configure itself for parallel data mode.
Logic high indicates that the flex I/O will configure itself for interleaved data mode.
For flex I/O Configuration, The 10/20 pin control applies only if the SPI bus is disabled and the device is
configured for HD mode. 10/20 is latched during the rising edge of RESET.
10/20 (IFACE2) is used to identify interleaved data mode or parallel data modes.
Logic low indicates that the flex I/O will configure itself for HD20 mode.
Logic high indicates that the flex I/O will configure itself for HD10 mode.
SPI_CS is latched during the rising edge of RESET.
Logic low results in the SPI being disabled and SPI_DIO, SPI_CLK and SPI_SDO act as mode pins.
Logic high results in the SPI being fully operational, and some of the mode pins are disabled.
Interpolation/PLL Factor Configuration. This control applies only if the SPI bus is disabled.
SPI_DIO (Interp1) and SPI_CLK (Interp0) configure the Tx path for 1× [00], 2× [01], or 4× [10] interpolation and
also enable the PLL of the same multiplication factor.
Power-Down Control. RxPwrDwn logic level controls the power-down function of the Rx path.
Logic low results in the Rx path operating at normal power levels.
Logic high disables the ADC clock and disables some bias circuitry to reduce power consumption.
Power-Down Control. TxPwrDwn logic level controls the power-down function of the Tx path.
Logic low results in the Tx path operating at normal power levels.
Logic high disables the DAC clocks and disables some bias circuitry to reduce power consumption.
Power-Down Control. Tx/Rx pin enables the appropriate Tx or Rx path in the half-duplex mode.
A logic low disables the Tx digital clock and the I/O bus is configured as an output or three-stated.
A logic high disables the Rx digital clocks and the I/O bus is configured as high impedance inputs.
Rev. 0 | Page 34 of 52
AD9861
Configuring with SPI
The flexible interface can be configured with register settings. Using the register allows more device programmability. Table 16 shows the
required register writes to configure the AD9861 for FD, optional FD, HD20, optional HD20, HD10, optional HD10, and clone mode.
Note that for modes that use interleaved data buses, enabling 2× or 4× interpolation is required.
Table 16. Registers for Configuring SPI
Register Address
FD, Mode 1
Register 0x01 [7:5]
Register 0x14 [4]
Register 0x14 [2]
Register 0x13 [1:0]
Optional FD, Mode 2
Register 0x01 [7:5]
Register 0x14 [4]
Register 0x14 [2]
Register 0x13 [1:0]
HD20, Mode 4
Register 0x01 [7:5]
Register 0x14 [4]
Register 0x14 [2]
Register 0x13 [1:0]
Optional HD20, Mode 5
Register 0x01 [7:5]
Register 0x14 [4]
Register 0x14 [2]
Register 0x13 [1:0]
HD10, Mode 7
Register 0x01 [7:5]
Register 0x14 [4]
Register 0x14 [2]
Register 0x13 [1:0]
Optional HD10, Mode 8
Register 0x01 [7:5]
Register 0x14 [4]
Register 0x14 [2]
Register 0x13 [1:0]
Clone, Mode 10
Register 0x01 [7:5]
Register 0x14 [0]
Register 0x13 [1:0]
Setting
Description
[000];
High
High
[01] or [10]
clk_mode—Configures timing mode.
SpiFDnHD—Configures FD mode.
SpiB10n20—Configures FD mode.
Interpolation Control—Configures 2× or 4× interpolation.
[001]
High
High
[01] or [10]
clk_mode—Configures timing mode.
SpiFDnHD—Configures FD mode.
SpiB10n20—Configures FD mode.
Interpolation Control—Configures 2× or 4× interpolation.
[000];
Low
Low
[00], [01] or [10]
clk_mode—Configures timing mode.
SpiFDnHD—Configures HD mode.
SpiB10n20—Configures HD20 mode.
Interpolation Control—Configures 1×, 2×, or 4× interpolation.
[011]
Low
Low
[00], [01] or [10]
clk_mode—Configures timing mode.
SpiFDnHD—Configures HD mode.
SpiB10n20—Configures HD20 mode.
Interpolation Control—Configures 1×, 2×, or 4× interpolation.
[000]
Low
High
[01] or [10]
clk_mode—Configures timing mode.
SpiFDnHD—Configures HD mode.
SpiB10n20—Configures HD10 mode.
Interpolation Control—Configures 2× or 4× interpolation.
[101]
Low
High
[01] or [10]
clk_mode—Configures timing mode.
SpiFDnHD—Configures HD mode.
SpiB10n20—Configures HD10 mode.
Interpolation Control—Configures 2× or 4× interpolation.
[111]
High
[01] or [10]
clk_mode—Configures timing mode.
SpiClone—Configures clone mode.
Interpolation Control—Configures 2× or 4× interpolation.
Rev. 0 | Page 35 of 52
AD9861
SPI Register Map
Registers 0x00 to 0x29 of the AD9861 provide flexible operation of the device. The SPI allows access to many configurable options.
Detailed descriptions of the bit functions are found in Table 18.
Table 17. Register Map
Reg. Name
General
Clock Mode
Addr
0x00
0x01
7
SDIO BiDir
clk_mode[2:0]
Power-Down
0x02
Tx Analog
RxA Power-Down
RxB Power-Down
Rx Power-Down
Rx Path
0x03
0x04
0x05
0x06
Rx_A Analog
Rx_B Analog
Rx Analog Bias
Rx Path
0x07
Rx Path
0x08
Rx path
0x09
Rx Path
0x0A
Tx Path
Tx Path
0B
0C
DAC A Offset [9:2]
DAC A Offset [1:0]
Tx Path
Tx Path
Tx Path
0D
0E
0F
DAC A Coarse Gain Control
DAC B Offset [9:2]
DAC B Offset [1:0]
DAC A Fine Gain [5:0]
Tx Path
Tx Path
Tx Path
10
11
12
DAC B Coarse Gain Control
TxPGA Gain [7:0]
TxPGA Slave
Enable
Tx Twos
Rx Twos
Complement
Complement
DAC B Fine Gain [5:0]
I/O Configuration 13
I/O Configuration
Clock
Clock
Auxiliary
Converters
AuxADC
14
15
16
17
18
AuxADC
19
AuxADC
AuxADC
AuxADC
AuxADC
AuxADC
AuxADC
AuxADC
AuxADC
AuxDAC
1A
1B
1C
1D
1E
1F
22
23
24
25
26
28
29
6
LSB First
5
Soft Reset
4
TxDigital
Rx_A DC Bias
Rx_B DC Bias
RxRef
DiffRef
Rx_A Twos
Complement
Rx_B Twos
Complement
3
RxDigital
2
1
Enable IFACE2
clkout
PLL PowerDown
Inv clkout
(IFACE3)
PLL Output
Disconnect
0
VREF
Rx_A Clk
Duty
Rx_B Clk
Duty
Rx Ultralow Rx Ultralow
Power Control Power Control
Rx Ultralow
Power Control
Rx Ultralow
Power Control
Rx Ultralow
Power Control
Rx Ultralow
Power Control
Rx Ultralow
Power Control
Rx Ultralow
Power Control
DAC A Offset
Direction
PLL Bypass
AuxDAC A FS [1:0]
DAC B Offset
Direction
TxPGA Fast
Update
Tx Inverse
Sample
Dig Loop On
SpiFDnHD
Alt Timing Mode
ADC Clock Div
PLL to IFACE2
AuxDAC B FS [1:0]
Start Average
AuxADC A
Start Average
AuxADC B
AuxADC A2 [1:0]
AuxADC A2 [9:2]
AuxADC A1 [1:0]
AuxADC A1 [9:2]
AuxADC B [1:0]
AuxADC B [9:2]
AuxSPI Enable
Sel 2not1
Refsel B
AuxDAC A [7:0]
AuxDAC B [7:0]
AuxDAC C [7:0]
Slave Enable
AuxDAC C Sync
TxPwrDwn
AuxDAC B Sync
TxPwrDwn
AuxDAC A Sync
TxPwrDwn
Interpolation Control [1:0]
SpiTxnRx
PLL Div5
SpiB10n20
SPI IO Control SpiClone
PLL Multiplier [2:0]
PLL Slow
AuxDAC C FS [1:0]
AuxADC Ref AuxADC Ref
Enable
FS
Number of AuxADC A Samples [2:0]
Number of AuxADC B Samples [2:0]
Rev. 0 | Page 36 of 52
Start B
Refsel A
Select A
Start A
AuxADC Clock Div[1:0]
Update C
Power-Up C
Update B
Power-Up B
Update A
Power-Up A
AD9861
Table 18. Register Bit Descriptions
Register Bit
Register 0: General
Bit 7: SDIO BiDir (Bidirectional)
Bit 6: LSB First
Bit 5: Soft Reset
Register 1: Clock Mode
Bits 7–5: Clk Mode
Bit 2: Enable IFACE2 clkout
Bit 1: Inv clkout (IFACE3)
Register 2: Power-Down
Bits 7–5: Tx Analog (PowerDown)
Bit 4: Tx Digital (Power-Down)
Bit 3: Rx Digital (Power-Down)
Bit 2: PLL Power-Down
Bit 1: PLL Output Disconnect
Register 3/4: Rx Power-Down
Bit 7: Rx_A Analog/
Rx_B Analog (Power-Down)
Bit 6: Rx_A DC Bias/
Rx_B DC Bias (Power-Down)
Register 5: Rx Power-Down
Bit 7: Rx Analog Bias (PowerDown)
Description
Default setting is low, which indicates that the SPI serial port uses dedicated input and output lines
(4-wire interface), SDIO and SDO pins, respectively. Setting this bit high configures the serial port to
use the SDIO pin as a bidirectional data pin.
Default setting is low, which indicates MSB first SPI port access mode. Setting this bit high
configures the SPI port access to LSB first mode.
Writing a high to this register resets all the registers to their default values and forces the PLL to
relock to the input clock. The soft reset bit is a one-shot register, and is cleared immediately after
the register write is completed.
These bits represent the clocking interface for the various modes. Setting 000 is default. Setting 111
is used for clone mode. Refer to the Summary of Flexible I/O Modes section for definition of clone mode.
Setting
Mode
000
Standard FD, HD10, HD20 Clock (Modes 1, 4, 7)
001
Optional FD timing (Mode 2)
010
Not Used
011
Optional HD20 timing (Mode 5)
100
Not Used
101
Optional HD10 timing (Mode 8)
110
Not Used
111
Clone Mode (Mode 10)
Enables the IFACE2 port to be an output clock. Also inverts the IFACE2 output clock in full-duplex
mode.
Invert the output clock on IFACE3.
Three options are available to reduce analog power consumption for the Tx channels. The first two
options disable the analog output from Tx Channel A or B independently, and the third option
disables the output of both channels and reduces the power consumption of some of the additional analog support circuitry for maximum power savings. With all three options, the DAC bias
current is not powered down so recovery times are fast (typically a few clock cycles). The list below
explains the different modes and settings used to configure them.
Power-Down Option Bits Setting [7:5]
Power-Down Tx A Channel Analog Output [1 0 0]
Power-Down Tx B Channel Analog Output [0 1 0]
Power-Down Tx A and Tx B Analog Outputs [1 1 1]
Default setting is low, which enables the transmit path digital to operate as programmed through
other registers. By setting this bit high, the digital blocks are not clocked to reduce power
consumption. When enabled, the Tx outputs are static, holding their last update values.
Setting this bit high powers down the digital section of the receive path of the chip. Typically, any
unused digital blocks are automatically powered down.
Setting this register bit high forces the CLKIN multiplier to a power-down state. This mode can be
used to conserve power or to bypass the internal PLL. To operate the AD9861 when the PLL is
bypassed, an external clock equal to the fastest on-chip clock is supplied to the CLKIN.
Setting this register bit high disconnects the PLL output from the clock path. If the PLL is enabled, it
locks or stays locked as normal.
Either ADC or both ADCs can be powered down by setting the appropriate register bit high. The
entire analog circuitry of Rx channel is powered down, including the differential references, input
buffer, and the internal digital block. The band gap reference remains active for quick recovery.
Setting either of these bits high powers down the input common-mode bias network for the
respective channel and requires an input signal to be properly dc-biased. By default, these bits are
low, and the Rx inputs are self-biased to approximately AVDD/2 and accept an ac-coupled input.
Setting this bit high powers down all analog bias circuits related to the receive path (including the
differential reference buffer). Because bias circuits are powered down, an additional power saving,
but also a longer recovery time relative to other Rx power-down options, will result.
Rev. 0 | Page 37 of 52
AD9861
Register Bit
Bit 6: RxREF (Power-Down)
Bit 5: DiffRef (Power-Down)
Bit 4: VREF (Power-Down)
Registers 6/7: Rx Path
Bit 5: Rx_A Twos Complement/
Rx_B Twos Complement
Bit 4: Rx_A Clk Duty/Rx_B Clk
Duty
Registers 8/9/A: Rx Path
Rx Ultralow Power Control Bits
Registers 0B/0C/0E/0F: Tx Path
DAC A/DAC B Offset
DAC A/DAC B Offset Direction
Registers 0D/10: Tx Path
Bits 7, 6: DAC A/DAC B Coarse
Gain Control
Bits 5–0: DAC A/DAC B Fine Gain
MSB, LSB
Register 11: Tx Path
Bits 0–7: TxPGA Gain
MSB, LSB
Register 12: Tx Path
Bit 6: TxPGA Slave Enable
Description
Setting this register bit high powers down internal ADC reference circuits. Powering down these
circuits provides additional power saving over other power-down modes. The Rx path wake-up
time depends on the recovery of these references typically of the order of a few milliseconds.
Setting this bit high powers down the ADC’s differential references, REFT and REFB. Recovery time
depends on the value of the REFT and REFB decoupling capacitors.
Setting this register bit high powers down the ADC reference circuit, VREF. Powering down the Rx
band gap reference allows an external reference to drive the VREF pin setting full-scale range of the
Rx paths.
Default data format for the Rx data is straight binary. Setting this bit high generates twos
complement data.
Setting either of these bits high enables the respective channels on-chip duty cycle stabilizer (DCS)
circuit to generate the internal clock for the Rx block. This option is useful for adjusting for high
speed input clocks with skewed duty cycle. The DCS mode can be used with ADC sampling
frequencies over 40 MHz.
Set all bits high, in combination with asserting the ADC_LO_PWR pin, to reduce the power
consumption of the Rx path by a fourth of normal Rx path power consumption.
These 10-bit, twos complement registers control a dc current offset that is combined with the Tx A
or Tx B output signal. An offset current of up to ±12% IOUTFS (2.4 mA for a 20 mA full-scale output)
can be applied to either differential pin on each channel. The offset current can be used to
compensate for offsets that are present in an external mixer stage, reducing LO leakage at its
output. The default setting is 0x00, no offset current. The offset current magnitude is set by using
the lower nine bits. Setting the MSB high adds the offset current to the selected differential pin,
while an MSB low setting subtracts the offset value.
This bit determines to which of the differential output pins for the selected channel the offset
current is applied. Setting this bit low applies the offset to the negative differential pin. Setting this
bit high applies the offset to the positive differential pin.
These register bits scale the full-scale output current (IOUTFS) of either Tx channel independently.
IOUT of the Tx channels is a function of the RSET resistor, the TxPGA setting, and the coarse gain
control setting.
00
Output current scaling by 1/11
01
Output current scaling by ½
10
No output current scaling
11
No output current scaling
The DAC output curve can be adjusted fractionally through the gain trim control. Gain trim of up to
±4% can be achieved on each channel individually. The gain trim register bits are a twos
complement attention control word.
100000
Maximum positive gain adjustment
111111
Minimum positive gain adjustment
000000
No adjustment (default)
000001
Minimum negative gain adjustment
011111
Maximum negative gain adjustment
This 8-bit, straight binary (Bit 0 is the LSB, Bit 7 is the MSB) register controls for the Tx programmable
gain amplifier (TxPGA). The TxPGA provides a 20 dB continuous gain range with 0.1 dB steps (linear
in dB) simultaneously to both Tx channels. By default, this register setting is 0xFF.
0000 0000
Minimum gain scaling –20 dB
1111 1111
Maximum gain scaling 0 dB
The TxPGA gain is controlled through register TxPGA gain setting and, by default, is updated
immediately after the register write. If this bit is set, the TxPGA gain update is synchronized with the
falling edge of a signal applied to the TxPwrDwn pin and is enabled during the wake-up from
power-down.
Rev. 0 | Page 38 of 52
AD9861
Register Bit
Bit 4: TxPGA Fast Update (Mode)
Register 13: I/O Configuration
Bit 7: Tx Twos Complement
Bit 6: Rx Twos Complement
Bit 5: Tx Inverse Sample
Bits 1,0: Interpolation Control
Register 14: I/O Configuration
Bit 5: Dig Loop On
Bit 4: SPI_FDnHD
Bit 3: SpiTxnRx
Bit 2: SpiB10n20
Bit 1: SPI IO Control
Bit 0: SpiClone
Register 15: Clock
Bit 7: PLL_Bypass
Bits 5: ADC Clock Div
Bit 4: Alt Timing Mode
Bit 3: PLL Div5
Bits 2–0: PLL Multiplier
Register 16: Clock
Bit 5: PLL to IFACE2
Bit 2: PLL Slow
Description
The TxPGA fast bit controls the update speed of the TxPGA. When fast update mode is enabled, the
TxPGA provides fast gain settling within a few clock cycles, which may introduce spurious signals at
the output of the Tx path. The default setting for this bit is low, and the TxPGA gives a smooth
transition between gain settings. Fast mode is enabled when this bit is set high.
The default data format for Tx data is straight binary. Set this bit high when providing twos
complement Tx data.
The default data format for Rx data is straight binary. Set this bit high when providing twos
complement Rx data.
By default, the transmit data is sampled on the rising edge of the CLKOUT. Setting this bit high
changes this, and the transmit data is sampled on the falling edge.
These register bits control the interpolation rate of the transmit path. The default settings are both
bits low, indicating that both interpolation filters are bypassed. The MSB and LSB are Address Bits 1
and 0, respectively. Setting binary 01 provides an interpolation rate of 2×; binary 10 provides an
interpolation rate of 4×.
When enabled, this bit enables a digital loop back mode. The digital loop-back mode provides a
means of testing digital interfaces and functionality at the system level. In digital loop-back mode,
the full-duplex interface must be enabled. (Refer to the Flexible I/O Interface Options section.) The
device accepts digital input from the bus according to the FD mode timing and uses the Tx digital
path (with enabled interpolation and other digital settings); the processed data is then output from
the Rx path bus.
Control bit to configure full-duplex (high) or half-duplex (low) interface mode. This register, in
combination with the SpiB10n20 register, configures the interface mode of FD, HD10, or HD20. The
register setting is ignored for clone mode operation. By default, this register is set high, and the
device is in FD mode.
Control bit used for toggling between transmit or receive mode for the half-duplex clock modes.
High represents Tx and low represents Rx.
Control bit for 10-bit or 20-bit modes. High represents 10-bit mode and Low represents 20-bit mode.
Use in conjunction with SpiTxnRx [Register14, Bit 3] to override external TxnRx pin operation.
Set high when in clone mode (see the Flexible I/O Interface Options section for definition of clone
mode). Clk_mode should also be set to binary 111, i.e., [Register 01[7:5] = 111.
Setting this bit high bypasses the PLL. When bypassed, the PLL remains active.
By default, the ADCs are driven directly from CLKIN in normal timing operation or from the PLL
output clock in the alternative timing operation. This bit is used to divide the source of the ADC
clock prior to the ADCs. The default setting is low and performs no division. Setting this bit high
divides the clock by 2.
The timing table in the data sheet describes two timing modes: the normal timing operation mode
and the alternative timing operation mode. The default configuration is normal timing mode and
the CLKIN drives the Rx path. In alternative timing mode, the PLL output is used to drive the Rx
path. The alternative operation mode is configured by setting this bit high.
The output of the PLL can be divided by 5 by setting this bit high. By default, the PLL directly drives
the Tx digital path with no division of its output.
These bits control the PLL multiplication factor. A default setting is binary 000, which configures the
PLL to 1× multiplication factor. This register, in combination with the PLL Div5 register, sets the PLL
output frequency. The programmable multiplication factors are
000
1×
001
2×
010
4×
011
8×
100
16×
101 – 111
not used
Setting this bit high switches the IFACE2 output signal to the PLL output clock. It is valid only if
Register 0x01, Bit 2 is enabled or if full-duplex mode is configured.
Changes the PLL loop bandwidth and changes the profile of the phase noise generated from the
PLL clock.
Rev. 0 | Page 39 of 52
AD9861
Register Bit
Register 17: Auxiliary Converters
Bits 7–2: AuxDAC A FS/AuxDAC B
FS/AuxDAC C FS
Bit 1: AuxADC Ref Enable
Bit 0: AuxADC Ref FS
Registers 18/19 : AuxADC
Bit 7: Start Average AuxADC A/
Start Average AuxADC B
Bit 7: Number of AuxADC A/
AuxADC B Samples
Registers 1A–21: AuxADC
Register 22: AuxADC
Bit 7: AuxSPI (Enable)
Bit 6: Sel 2not1
Bits 5, 2: Refsel B/A
Bit 1: Select A
Bit 3, 0: Start B/A
Description
These register bits independently scale the full-scale output voltage for the AuxDACs. If the fullscale voltage is programmed to a value greater than PLL_VDD – 0.2 V, the AuxDAC becomes
nonlinear in this region.
MSB, LSB
AuxDAC Full-Scale Output Voltage
00
3.0 V
01
3.3 V
10
2.5 V
11
2.7 V
This bit enables the on-chip, supply independent reference for the AuxADC. By default, the AuxADC
uses the PLL_AVDD supply for its full-scale voltage level.
When the AuxADC Ref Enable bit is set high, this bit allows the user to select the full-scale value of
the AuxADC. A low setting sets the full-scale value to 3.0 V; a high setting sets the full-scale value to
2.5 V. If the full-scale voltage is programmed to a value greater than PLL_VDD – 0.2 V, the AuxADC is
not linear in this region.
These registers are used to initiate a conversion cycle of the AuxADCs for a number of consecutive
samples and then report the average result. The number of consecutive samples is programmed in
the number of AuxADC A/AuxADCB samples register. The external pin Aux_SPI_CS can be configured to allow it to initiate the start average conversion cycle. The result is placed in the appropriate
register corresponding to the AuxADC output [Registers 0x1A to 0x21].
These bits control the number of samples that the AuxADC collects and uses to calculate an
average value. This register is used in conjunction with the start average AuxADC register.
MSB, LSB
Number of Samples to Average
000
1
001
2
010
4
011
8
100
16
101
32
110
64
111
Not Used
These 10-bit, offset binary registers are read-only and store the last corresponding AuxADC output
values. The AD9861 has two AuxADC SAR converters: AuxADC A and AuxADC B. AuxADC A has a
multiplexed input, which allows the user to select either input by using the Select A register. The 10
bits are broken into two registers, one containing the upper eight bits and the other containing the
lower two bits.
Enables the AuxSPI, which can be used to initiate a conversion and read back one of the AuxADCs.
If the auxiliary serial port is used, this bit selects which AuxADC, 1 or 2, uses the dedicated auxiliary
serial port. By default (low setting), the auxiliary serial port controls AuxADC A. Setting this bit high
allows the auxiliary serial port to control AuxADC B.
By default, the AuxADCs use an external reference applied to the AUX_REF pin. This voltage acts as
the full-scale reference for the selected AuxADC. Either AuxADC can use an internally generated
reference, which can be a buffered version of the analog supply voltage or a supply independent,
3.0 V or 2.5 V internal reference. To enable use of the internal reference for either of the AuxADCs,
set the respective Refsel register high. For internal reference configuration, see Register 17.
This bit is used to select which of the two inputs is connected to the AuxADC. By default (setting
low), the AUX_ADC_A2 (Aux2 pin) is connected to AuxADC A. Setting the respective bit high
connects the AUX_ADC_A1 (Aux1 pin) to AuxADC A.
Setting either of these bits to high initiates a conversion of the respective AuxADC, A or B. The
register bit always reads back a low.
Rev. 0 | Page 40 of 52
AD9861
Register Bit
Register 23: AuxADC
Bits 1,0: AuxADC Clock Div
Registers 24, 25, 26: AuxDAC
AuxDAC A, B, and C Output
Control Word
Register 28: AuxDAC
Bit 7: Slave Enable
Bits 2/1/0: Update C, B, and A
Register 29: AuxDAC
Bits 7/6/5: AuxDAC C/B/A Sync
TxPwrDwn
Bits 2/1/0: Power Up C, B, and A
Description
The AuxADCs clock can be based on either the clock driving the Rx ADC, or it can be driven from
the SPI_CLK. The conversion rate of the AuxADCs should be less than 40 MHz. In order to facilitate a
slower speed clock for the AuxADC, these bits are used to divide down the Rx ADC clock prior to
driving the AuxADC. The following options are programmable through this register:
MSB, LSB
AuxADC Sampling Rate
00
Rx ADC Clock/4
01
Rx ADC Clock/2
10
Rx ADC Clock
11
SPI_CLK drives AuxADC
Three 8-bit, straight binary words are used to control the output of three on-chip AuxDACs. The
AuxDAC output changes take effect immediately after any of the serial writes are completed. The
DAC output control words have default values of 0. The smaller programmed output controlled
words correspond to lower DAC output levels.
A low setting (default) updates the AuxDACs after the respective register is written to. To
synchronize the AuxDAC outputs to each other, a slave mode can be enabled by setting this bit
high and then setting the appropriate update registers high.
Setting a high bit to any of these bits initiates an update of the respective AuxDAC, A, B or C, when
slave mode is enabled using the slave enable register. The register bit is a one-shot and always
reads back a low. Be sure to keep the slave enable bit high when using the AuxDAC synchronization
option.
Setting any of these bits high synchronizes AuxDAC updates only when the TxPwrDwn rising edge
occurs. This syncronizes the AuxDAC update to the Tx path power-up.
Setting any of these bits high powers up the appropriate AuxDAC. By default, these bits are low and
the AuxDACs are disabled.
Rev. 0 | Page 41 of 52
AD9861
PROGRAMMABLE REGISTERS
The AD9861 contains internal registers that are used to configure
the device. A serial port interface provides read/write access to
the internal registers. Single-byte or dual-byte transfers are
supported as well as MSB first or LSB first transfer formats. The
AD9861’s serial interface port can be configured as a single pin
I/O (SDIO) or as two unidirectional pins for in/out (SDIO/SDO).
The serial port is a flexible, serial communications port, allowing
easy interface to many industry-standard microcontrollers and
microprocessors.
General Operation of the Serial Interface
By default, the serial port accepts data in MSB first mode and
uses four pins: SEN, SCLK, SDIO, and SDO by default. SEN is a
serial clock enable pin; SCLK is the serial clock pin; SDIO is a
bidirectional data line; and SDO is a serial output pin.
SEN is an active low control gating read and write cycles. When
SEN is high, SDO and SDIO go into a high impedance state.
SCLK is used to synchronize SPI read and writes at a maximum
bit rate of 30 MHz. Input data is registered on the rising edge,
and output data transitions are registered on the falling edge.
During write operations, the registers are updated after the 16th
rising clock edge (and 24th rising clock edge for the dual-byte
case). Incomplete write operations are ignored.
cycle. Phase 2 is the actual data transfer between the AD9861
and the system controller. Phase 2 of the communication cycle
is a transfer of one or two data bytes as determined by the
instruction byte. Normally, using one communication cycle in a
multibyte transfer is the preferred method; however, single byte
communication cycles are useful to reduce CPU overhead when
register access requires only one byte. An example of this is to
write the AD9861 power-down bits.
All data input to the AD9861 is registered on the rising edge of
SCLK. All data is driven out of the AD9861 on the falling edge
of SCLK.
Instruction Byte
The instruction byte contains the information shown in
Table 19, and the bits are described in detail after the table.
Table 19. Instruction Byte
MSB
R/nW
D6
2/n1
Byte
D5
A5
D4
A4
D3
A3
D2
A2
D1
A1
LSB
A0
R/nW—Bit 7 of the instruction byte determines whether a read
or write data transfer will occur after the instruction byte write.
Logic high indicates a read operation. Logic low indicates a
write operation.
SDIO is an input data only pin by default. Optionally, a 3-pin
interface may be configured using the SDIO for both input and
output operations and three-stating the SDO pin. Refer to the
SDIO BiDir bit in Register 0x00 (Table 18).
2/n1 Byte—Bit 6 of the instruction byte determines the number
of bytes to be transferred during the data transfer cycle of the
communication cycle. Logic high indicates a 2-byte transfer.
Logic low indicates a 1-byte transfer.
SDO is a serial output data pin used for readback operations in
A5, A4, A3, A2, A1, A0—Bits 5, 4, 3, 2, 1, and 0 of the
instruction byte determine which register is accessed during the
data transfer portion of the communication cycle. For 2-byte
transfers, this address is the starting byte address. The second
byte address is automatically decremented when the interface is
configured for MSB first transfers. For LSB first transfers, the
address of the second byte is automatically incremented.
4-wire mode and is three-stated when SDIO is configured for
bidirectional operation.
There are two phases to a communication cycle with the AD9861.
Phase 1 is the instruction cycle, which is the writing of an
instruction byte into the AD9861, coincident with the first eight
SCLK rising edges. The instruction byte provides the AD9861
serial port controller with information regarding the data
transfer cycle, which is Phase 2 of the communication cycle. The
Phase 1 instruction byte defines whether the upcoming data
transfer is read or write, the number of bytes in the data transfer
(one or two), and the starting register address for the first byte
of the data transfer.
Table 20. Serial Port Interface Timing
Maximum SCLK Frequency (fSCLK)
Minimum SCLK High Pulse Width (tPWH)
Minimum SCLK Low Pulse Width (tPWL)
Maximum Clock Rise/Fall Time
Data to SCLK timing (tDS)
Data Hold Time (tDH)
The first eight SCLK rising edges of each communication cycle
are used to write the instruction byte into the AD9861. The
remaining SCLK edges are for Phase 2 of the communication
Rev. 0 | Page 42 of 52
40 MHz
12.5 ns
12.5 ns
1 ms
12.5 ns
0 ns
AD9861
Write Operations
The SPI write operation uses the instruction header to configure a 1-byte or 2-byte register write using the 2/n1 byte setting.
The instruction byte followed by the register data is written
serially into the device through the SDIO pin on rising edges of
the interface clock, SCLK. The data can be transferred MSB first
or LSB first depending on the setting of the LSB first register bit.
The write operation is the same regardless of SDIO BiDir
register setting.
tDS
tHI
tH
tCLK
tDH
tS
Figure 78 to Figure 80 are examples of writing data into the
device. Figure 78 shows a 1-byte write with MSB first; Figure 79
shows a 2-byte write with MSB first; and Figure 80 shows a
2-byte write with LSB first. Note the differences between LSB
and MSB first modes: both the instruction header and data are
reversed, and the second data byte register location is different.
In the default MSB first mode, the second data byte is written to
a decremented register address. In LSB first mode, the second
data byte is written to an incremented register address.
tLO
SEN
SCLK
DON'T CARE
SDIO
DON'T CARE
DON'T CARE
R/W
2/1
A5
A4
A3
A2
A1
A0
D7
D6
D5
INSTRUCTION HEADER
D4
D3
D2
D1
D0
DON'T CARE
REGISTER DATA
03606-0-022
Figure 78. 1-Byte Serial Register Write in MSB First Mode
tHI
tLO
tS
tH
tDH
tDS
SEN
tCLK
DON'T CARE
SCLK DON'T CARE
SDIO DON'T CARE
R/W
2/1
A5
A4
A3
A2
A1
A0
D7
D6
INSTRUCTION HEADER (REGISTER N)
D5
D4
D3
D2
D1
D0 D7
D6
REGISTER (N) DATA
D5
D4
D3
D2
D1
D0
DON'T CARE
REGISTER (N–1) DATA
03606-0-023
Figure 79. 2-Byte Serial Register Write in MSB First Mode
tS
SEN
tHI
tLO
tDS
tDH
tH
tCLK
DON'T CARE
SCLK DON'T CARE
SDIO DON'T CARE
A0
A1
A2
A3
A4
A5
2/1 R/W D0
INSTRUCTION HEADER (REGISTER N)
D1
D2
D3
D4
D5
D6
D7
D0
D1
REGISTER (N) DATA
Figure 80. 2-Byte Serial Register Write in LSB First Mode
Rev. 0 | Page 43 of 52
D2
D3
D4
D5
REGISTER (N+1) DATA
D6
D7
DON'T CARE
03606-0-024
AD9861
Read Operation
can be configured by setting the SDIO BiDir register. In 3-wire
mode, the SDIO pin becomes an output pin after receiving the
8-bit instruction header with a readback request.
The readback of registers can be a single or dual data byte
operation. The readback can be configured to use 3-wire or
4-wire and can be formatted with MSB first or LSB first. The
instruction header is written to the device either MSB or LSB
first (depending on the mode) followed by the 8-bit output data
(appropriately MSB or LSB justified). By default, the output data
is sent to the dedicated output pin (SDO). Three-wire operation
tS
tHI
tDS
SCLK
DON'T CARE
SDIO
DON'T CARE
tCLK
tH
tDV
tLO
tDH
SEN
Figure 81 shows a 4-wire SPI read with MSB first; Figure 82
shows a 3-wire read with MSB first; and Figure 83 shows a
4-wire read with LSB first.
DON'T CARE
R/W
2/1
A5
A4
A3
A2
A1
A0
DON'T CARE
INSTRUCTION HEADER
D7
DON'T CARE
SDO
D6
D5
D4
D3
D2
D1
D0
DON'T CARE
OUTPUT REGISTER DATA
03606-0-025
Figure 81. 1-Byte Serial Register Readback In MSB First Mode, SDIO BiDir Bit Set Logic Low (Default, 4-Wire Mode)
tS
tHI
tDS
tDH
SEN
SCLK
DON'T CARE
SDIO
DON'T CARE
tCLK
tH
tDV
tLO
DON'T CARE
R/W
2/1
A5
A4
A3
A2
A1
A0
D7
D6
INSTRUCTION HEADER
D5
D4
D3
D2
D1
D0
DON'T CARE
OUTPUT REGISTER DATA
03606-0-026
Figure 82. 1-Byte Serial Register Readback in MSB First Mode, SDIO BiDir Bit Set Logic High (Default, 3-Wire Mode)
tS
SDIO
tCLK
tH
tDV
tLO
tDH
SEN
SCLK
tHI
tDS
DON'T CARE
DON'T CARE
DON'T CARE
A0
A1
A2
A3
A4
A5
2/1
DON'T CARE
R/W
INSTRUCTION HEADER
SDO
DON'T CARE
D0
D1
D2
D3
D4
D5
D6
D7
DON'T CARE
OUTPUT REGISTER DATA
03606-0-027
Figure 83. 1-Byte Serial Register Readback in LSB First Mode, SDIO BiDir Bit Set Logic Low (Default, 4-Wire Mode)
Rev. 0 | Page 44 of 52
AD9861
Table 21. PLL Input and Output Minimum and Maximum
Clock Rates
CLOCK DISTRIBUTION BLOCK
Theory/Description
The AD9861 uses a clock distribution block to distribute the
timing derived from the input clock (applied to the CLKIN pin,
referred to here as CLKIN) to the Rx and Tx paths. There are
many options for configuring the clock distribution block,
which are available through internal register settings. The Clock
Distribution Block Diagram section describes the timing block
diagram breakdown, followed by the data timing for the
different data interface options.
The clock distribution block contains a PLL, which includes an
optional output divide-by-5 circuit, an ADC divide-by-2 circuit,
multiplexers, and other digital logic.
There are two main methods of configuring the Rx path timing
of the AD9861, normal timing mode and alternative timing
mode, which are controlled through register Alt timing mode
[Register 0x15, Bit 4]. In normal timing mode, the Rx path clock
is driven directly from the CLKIN input and the Tx path is
driven by a clock derived from CLKIN multiplied by the on
chip PLL. In alternative timing mode, the input clock is applied
to the PLL circuitry, and the PLL output clock drives both the
Rx path clock and Tx path clock.
Because alternative timing mode uses the PLL to derive the Rx
path clock, the ADC performance may degrade slightly. This
degradation is due to the phase noise from the PLL. Typically it
occurs in undersampling applications when the input signal is
above the first Nyquist zone of the ADC.
The PLL can provide 1×, 2×, 4×, 8×, and 16× multiplication or
can be bypassed and powered down through register PLL
bypass [Register 0x15, Bit 7] and through register PLL powerdown [Register 0x2, Bit 2]. The PLL requires a minimum input
clock frequency of 16 MHz and needs to provide a minimum
PLL output clock of 32 MHz. This limit applies to the PLL
output prior to the optional divide-by-5 circuitry. For clock
frequencies below these limits, the PLL must be bypassed. The
PLL maximum output frequency before the divide-by-5 circuitry is 350 MHz. Table 21 shows the input and output clock
rates for all the multiplication settings.
PLL Setting
1× (PLL Bypassed)
1× (PLL Enabled)
2×
4×
8×
* 1/5 ×
* 2/5 ×
* 4/5 ×
* 8/5 ×
* 16/5 ×
Input Clock
(Min/Max) (MHz)
1/200
32/200
16/100
16/50
16/25
32/200
16/175
16/87.5
16/43.75
16/21.875
Output Clock
(Min/Max) (MHz)
1/200
32/200
32/200
64/200
128/200
6.4/40
6.4/70
12.8/70
25.6/70
51.2/70
* Indicates PLL output divide-by-5 circuit enabled.
Clock Distribution Block Diagram
The Clock Distribution Block diagram is shown in
Figure 84. An output clock formatter configures the output
synchronization signals, IFACE1, IFACE2, and IFACE3. These
interface pin signals depend on clock mode setting, data I/O
configuration, and other operational settings. Clock mode and
data I/O configuration are defined in register settings of
clk_mode, SpiFDnHD, and SpiB10n20.
Table 22 shows the configuration of the IFACE1, IFACE2 and
IFACE3 pins relative to clock mode (for half-duplex cases, the
IFACE1 pin is an input that identifies if the device is in Rx or Tx
operation mode). The clock mode is used to specify the timing
for each data interface operation modes, which are discussed in
detail in the Flexible I/O Interface Options section. The T and R
extensions after the half-duplex Modes 4, 5, 7, 8, and 10 in the
Table 22 indicate that the device is in transmit or receive
operation mode. The default clock mode setting [Register 0x01,
Bits 5–7, clk_mode] of ‘000’ configures clock Mode 1 for the
full-duplex operation, Mode 4 for half-duplex 20 operation and
Mode 7 for half-duplex 10 operation. Modes 2, 5, 8, and 10 are
optional timing configurations for the AD9861 that can be
programmed through Register 0x01 clk_mode.
Rev. 0 | Page 45 of 52
AD9861
80MHz MAX
1, 2
CLKIN
Rx
DIGITAL
BLOCK
4
1
1, 2, 4, 8, 16
Rx
PATH
IFACE2
OUTPUT
CLOCK
FORMATTER
1, 5
Tx
DIGITAL
BLOCK
3
IFACE3
Tx
PATH
5
6
2
03606-0-067
1. ALTERNATE TIMING MODE: REG 0x15, BIT 4
2. PLL MULTIPLICATION SETTING: REG 0x15, BITS 2–0
3. PLL OUTPUT DIVIDE BY 5; REG 0x15, BIT 3
4. Rx PATH DIVIDE BY 2: REG 0x15, BIT 5
5. PLL BYPASS PATH: REG 0x15, BIT 7
6. INTERP CONTROL, Tx/Rx INV IFACE3, CLK MODE, INV IFACE2, FD/HD, 10/20
Figure 84. Clock Distribution Block Diagram
Table 22. Interface Pins (IFACE1, IFACE2, IFACE3) Configuration Definition for Flexible Interface Operation
1
Clock
Mode
PIN
IFACE1
Full-Duplex
TxSync
IFACE2
IFACE3
Buff_CLKIN
Tx Clock
2
4T
4R
5T
RxSync
Half-Duplex, 20-Bit
Tx/Rx
Optional CLKOUT
Tx
Rx
Tx
Clock
Clock
Clock
The Tx clock output frequency depends on whether the data is
in interleaved or parallel (noninterleaved) configuration. Modes
1, 2, 7, 8, and 10 use Tx interleaved data and require either 2× or
4× interpolation to be enabled.
•
DAC update rate = CLKIN × PLL setting.
•
Noninterleaved Tx data clock frequency = CLKIN × PLL
setting × 1/(interpolation rate).
•
Interleaved Tx data clock frequency = 2 × CLKIN × PLL
setting × 1/(interpolation rate).
The Rx clock does not depend on whether the data is interleaved or parallel, but does depend on the configuration of the
timing mode: normal or alternative.
•
Normal timing mode, Rx clock frequency = CLKIN × ADC
Div factor (if enabled).
•
Alternative timing mode, Rx clock frequency = CLKIN ×
PLL setting × ADC Div factor (if enabled).
5R
7T
7R
8T
Rx
Clock
Half-Duplex, 10-Bit
Tx/Rx
Optional CLKOUT
Tx
Rx
Tx
Clock
Clock
Clock
8R
10T
10R
Rx
Clock
Clone Mode
Tx/Rx
Optional CLKOUT
Tx
Rx
Clock
Clock
An optional CLKOUT from IFACE2 is available as a stable
system clock running at the CLKIN frequency or the TxDAC
update rate, which is equal to CLKIN × PLL setting. Setting the
enable IFACE2 register [Register 0x01, Bit 2] enables the
IFACE2 optional clock output. In FD mode, the IFACE2 pin
always acts as a clock output; the enable IFACE2 pin can be
used to invert the IFACE2 output.
Configuration
The AD9861 timing for the transmit path and for the receive
path depend on the mode setting and various programmable
options. The registers that affect the output clock timing and
data input/output timing are clk_mode [2:0]; enable IFACE2;
inv clkout (IFACE3); Tx inverse sample; interpolation control;
PLL bypass; ADC clock div; Alt timing mode; PLL Div5; PLL
multiplication; and PLL to IFACE2. The clk_mode register is
discussed previously. Table 23 shows the other register bits that
are used to configure the output clock timing and data latching
options available in the AD9861.
Rev. 0 | Page 46 of 52
AD9861
Table 23. Serial Registers Related to the Clock Distribution Block
Register Name
Enable IFACE2
Register Address,
Bit(s)
Register 0x01, Bit 2
Inv clkout (IFACE3)
Register 0x01, Bit 1
Tx Inverse Sample
Register 0x13, Bit 5
Interpolation Control
PLL Bypass
Register 0x13, Bit 1:0
Register 0x15, Bit 7
ADC Clock Div
Register 0x15, Bit 5
Alt Timing Mode
Register 0x15, Bit 4
PLL Div5
Register 0x15, Bit 3
PLL Multiplier
PLL to IFACE2
Register 0x15, Bit 2:0
Register 0x16, Bit 5
Function
0: There is no clock output from IFACE2 pin, except in FD mode.
1: The IFACE2 pin outputs a continuous reference clock from the PLL output. In FD mode,
this inverts the IFACE2 output.
0: The IFACE3 clock output is not inverted.
1: The IFACE3 clock output is inverted.
0: The Tx path data is latched relative to the output Tx clock rising edge.
1: The Tx path data is latched relative to the output Tx clock falling edge.
Sets interpolation of 1×, 2×, or 4× for the Tx path.
0: The PLL block is used to generate system clock.
1: The PLL block is bypassed to generate system clock.
0: ADC clock rate equals the Rx path frequency.
1: ADC clock is one-half the Rx path frequency.
0: CLKIN is used to drive the Rx path clock.
1: PLL block output is used to drive the Rx path clock.
0: PLL block output clock is not divided down.
1: PLL block output clock is divided by 5.
Sets multiplication factor of the PLL block to 1× (000), 2× (001), 4× (010), 8× (011), or 16x (100).
0: If enable IFACE2 register is set, IFACE2 outputs buffered CLKIN.
1: If enable IFACE2 register is set, IFACE2 outputs buffered PLL output clock.
Transmit (Tx) timing requires specific setup and hold times to
properly latch data through the data interface bus. These timing
parameters are specified relative to an internally generated
output reference clock. The AD9861 has two interface clocks
provided through the IFACE3 and IFACE2 pins. The transmit
timing specifications, setup and hold time, provide a minimum
required window of valid data.
Setup time (tSETUP) is the time required for data to initially settle
to a valid logic level prior to the relative output timing edge.
Hold time (tHOLD) is the time after the output timing edge that
valid data must remain on the data bus to be properly latched.
Figure 85 shows tSETUP and tHOLD relative to IFACE3 falling edge.
Note that in some cases negative time is specified, for example
with tHOLD timing, which means that the hold time edge occurs
before the relative output clock edge.
tSETUP
tHOLD
IFACE3 (CLKOUT)
Table 24. AD9861 Typical Tx Data Latch Timing Relative to
IFACE3 Falling Edge
Mode No.
1
2
4
5
7
8
10
Mode Name
FD
Optional FD
HD20
Optional HD20
HD10
Optional HD10
Clone
tsetup (ns)
5
5
5
5
5
5
5
thold (ns)
–2.5
–2.5
–1.5
–1.5
–2.5
–2.5
–1.5
Receive (Rx) path data is output after a reference output clock
edge. The time delay of the Rx data relative to a reference output
clock is called the output delay, tOD. The AD9861 has two
possible interface clocks provided through the IFACE3 and
IFACE2 pins. Figure 86 shows tOD relative to IFACE3 rising
edge. Note that in some cases negative time is specified, which
means that the output data transition occurs prior to the relative
output clock edge.
Tx DATA
tOD
03606-0-028
Figure 85. Tx Data Timing Diagram
IFACE3 (CLKOUT)
Table 24 shows typical setup-and-hold times for the AD9861 in
the various mode configurations.
Rev. 0 | Page 47 of 52
Rx DATA
03606-0-029
Figure 86. Rx Data Timing Diagram
AD9861
Table 25 shows typical output delay times for the AD9861 in the various mode configurations.
Table 25. AD9861 Rx Data Latch Timing
Mode No.
1
Mode Name
FD
2
Optional FD
4
5
7
8
HD20
Optional HD20
HD10
Optional HD10
10
Clone
tOD Data Delay [ns]
+2.5 ns
+1 ns
+1 ns
+2 ns
−1.5 ns
−0.5 ns
−1.5 ns
+0.5 ns
+0 ns
+1.5 ns
Relative to:
Relative to IFACE2 rising edge
Relative to IFACE3 rising edge
Relative To IFACE3 rising edge
IFACE2 (RxSYNC) relative to LSB
Relative to IFACE3 rising edge
Relative to IFACE3 rising edge
Relative to IFACE3 rising edge
Relative to IFACE3 rising edge
U12 (RxSYNC) relative to LSB
Relative to IFACE3 rising edge
Configuration without Serial Port Interface
(Using Mode Pins)
The AD9861 can be configured using mode pins if a serial port interface is not available. This section applies only to configuring the
AD9861 without an SPI. Refer is the Digital Block, Configuring with Mode Pins section for further information.
When using the mode pin option, the pins shown in Table 26 are used to configured the AD9861.
Table 26. Using Mode Pin (SPI Disabled) to Configure Timing (SPI_CS, Pin 64, Must Be Tied Low)
Clock Mode
Mode 1 (FD)
Mode 4 (HD20)
Mode 7 (HD10)
1
Interpolation
Setting
PLL Setting
2×
4×
1×
2×
4×
2×
4×
2×
4×
Bypassed
2×
4×
2×
4×
Pin 17 (IFACE2) is an output clock in FD mode.
Rev. 0 | Page 48 of 52
FD/HD
Pin 3
1
10/20
Pin 17
N/A1
0
0
0
1
Interp1,Interp0
Pin 1, Pin 2
0, 1
1, 0
0, 0
0, 1
1, 0
0, 1
1, 0
AD9861
OUTLINE DIMENSIONS
9.00
BSC SQ
0.60 MAX
0.60 MAX
0.30
0.25
0.18
49
48
PIN 1
INDICATOR
TOP
VIEW
8.75
BSC SQ
PIN 1
INDICATOR
64
1
7.25
7.10 SQ*
6.95
BOTTOM
VIEW
0.45
0.40
0.35
33
32
17
16
0.25 MIN
7.50 REF
1.00
0.85
0.80
12°
MAX
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
0.20 REF
* COMPLIANT TO JEDEC STANDARDS MO-220-VMMD
EXCEPT FOR EXPOSED PAD DIMENSION
Figure 87. 64-Lead Lead Frame Chip Scale Package (LFCSP) [CP-64]
Rev. 0 | Page 49 of 52
AD9861
ORDERING GUIDE
Model
AD9861BCP-50
AD9861BCP-80
AD9861BCPRL-50
AD9861BCPRL-80
AD9861-50EB
AD9861-80EB
Temperature Range
–40°C to +85°C (Ambient)
–40°C to +85°C (Ambient)
–40°C to +85°C (Ambient)
–40°C to +85°C (Ambient)
25°C (Ambient)
25°C (Ambient)
Package Description
64-Lead LFCSP
64-Lead LFCSP
64-Lead LFCSP
64-Lead LFCSP
Evaluation Board
Evaluation Board
Rev. 0 | Page 50 of 52
Package Option
CP-64
CP-64
CP-64
CP-64
AD9861
NOTES
Rev. 0 | Page 51 of 52
AD9861
NOTES
© 2003 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C03606–0–11/03(0)
Rev. 0 | Page 52 of 52