LINER LT5502

Final Electrical Specifications
LT5502
400MHz Quadrature
IF Demodulator with RSSI
January 2001
U
DESCRIPTIO
FEATURES
■
■
■
■
■
■
■
■
■
■
■
The LT®5502 is a 70MHz to 400MHz monolithic integrated
quadrature IF demodulator. It consists of an IF limiter,
quadrature down mixers, integrated lowpass filters, and
divide-by-two LO buffers. The demodulator provides all
building blocks for demodulation of I and Q baseband
signals with a single supply voltage of 1.8V to 5.25V. The
IF limiter has 84dB small-signal gain, and a built-in receive
signal strength indicator (RSSI) with over 90dB linear
range. The input referred noise-spectral-density is
1.45nV/√Hz, which is equivalent to a 4dB noise figure
when the input is terminated with a 50Ω source. The
integrated lowpass output filters act as antialiasing and
pulse-shaping filters for demodulated I/Q-baseband signals. The 3dB cutoff frequency of the filters is about
7.7MHz. The VCO frequency is required to be twice the
desired operating frequency to provide quadrature local
oscillator (LO) signals to the mixers. The standby mode
provides fast transient response to the receive mode with
reduced supply current when the I/Q outputs are
AC-coupled to a baseband chip.
Single 1.8V to 5.25V Supply
IF Frequency Range: 70MHz to 400MHz
84dB Limiting IF Gain
90dB Linear RSSI Range
7.7MHz Lowpass Output Filter
Baseband I/Q Amplitude Imbalance: <0.7dB
4dB Noise Figure
Low Supply Current: 25mA
Outputs Biased Up While in Standby
Shutdown Current: 1µA
24-Lead Narrow SSOP Package
U
APPLICATIO S
■
■
■
IEEE802.11
High Speed Wireless LAN
Wireless Local Loop
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
I/Q Output Swing, RSSI Output vs IF Input Power
2V
C3
22nF
R1
240Ω
IF +
1200
VCC
IF –
2XLO
IOUT+
90°
2XLO
INPUT
QOUT+
÷2
0°
2XLO –
LT5502
ENABLE
EN
IOUT–
+
GND
BASEBAND
DIFFERENTIAL
I/Q OUTPUTS
QOUT–
RSSI
C4
1.8pF
5502 TA01a
1.2
1000
1.0
800
0.8
600
0.6
400
0.4
200
–85
RSSI OUTPUT (V)
IF
INPUT
C1
1nF
DIFFERENTIAL OUTPUT SWING (mVP-P)
C2
1µF
0.2
–70
–55
–40
–25
–10
IF INPUT POWER (dBm)
5
5502 TA01b
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
1
LT5502
U
W W
W
ABSOLUTE
AXI U RATI GS
U
W
U
PACKAGE/ORDER I FOR ATIO
(Note 1)
TOP VIEW
Power Supply Voltage ............................................ 5.5V
LO Input Power .................................................. 10dBm
IF Input Power .................................................... 10dBm
Operating Ambient
Temperature (Note 2) ..............................–40°C to 85°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
Voltage on any Pin not to Exceed ............................. VCC
+
1
24 QOUT+
IOUT–
2
23 QOUT–
GND
3
22 VCC
IOUT
VCC
4
21 GND
GND
5
20 GND
IF +
6
19 2XLO+
IF –
7
18 2XLO –
GND
8
17 VCC
GND
9
16 VCC
EN 10
15 RSSI
STBY 11
14 GND
IFt + 12
ORDER PART
NUMBER
LT5502EGN
13 IFt –
GN PACKAGE
24-LEAD NARROW PLASTIC SSOP
TJMAX = 150°C, θJA = 85°C/W
Consult factory for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
PIF = –50dBm, TA = 25°C, unless otherwise noted. (Note 3)
SYMBOL
PARAMETER
VCC = 3V, f2XLO = 570MHz, P2XLO = –10dBm, f IF = 280MHz,
CONDITIONS
MIN
TYP
MAX
UNITS
IF Input
fIF
Frequency Range
3dB Limiting Sensitivity
Noise Figure
Terminated 50Ω Source
DC Common Mode Voltage
70 to 400
MHz
–79
dBm
4
dB
2.6
V
850
mVP-P
Demodulator I/Q Output
I/Q Output Voltage Swing
Differential
I/Q Amplitude Mismatch
0.1
I/Q Phase Mismatch
Output Driving Capability
0.7
0.6
Differential; CMAX = 10pF
DEG
1.5
DC Common Mode Voltage
dB
kΩ
1.84
V
90
dB
3.8
kΩ
RSSI
Linear Dynamic Range (Note 4)
±3dB Linearity Error
Output Impedance
Output Voltage
Input = – 70dBm
0.27
0.41
0.54
V
Output Voltage
Input = 0dBm
0.8
1.01
1.2
V
Output Voltage Slope
Input from –70dBm to 0dBm
8.7
Linearity Error
Input from –70dBm to 0dBm
1
mV/dB
dB
Baseband Lowpass Filter
2
3dB Cutoff Frequency
7.7
MHz
Group Delay Ripple
16.4
ns
LT5502
ELECTRICAL CHARACTERISTICS
PIF = –50dBm, TA = 25°C, unless otherwise noted. (Note 3)
SYMBOL
PARAMETER
VCC = 3V, f2XLO = 570MHz, P2XLO = –10dBm, f IF = 280MHz,
CONDITIONS
MIN
TYP
MAX
UNITS
–5
dBm
2XLO
f2XLO
Frequency Range
P2XLO
Input Power
140 to 800
MHz
–20
DC Common Mode Voltage
2.6
V
Power Supply
VCC
Supply Voltage
1.8
ICC
Supply Current
IOFF
Shutdown Current
Standby Mode Current
EN = High
32
EN = Low; Standby = Low
1
100
µA
EN = Low; Standby = High
2.6
3.5
mA
U W
I/Q Output Swing vs IF Input Power
1200
fIF = 280MHz
DIFFERENTIAL OUTPUT SWING (mVP-P)
SUPPLY CURRENT (mA)
DIFFERENTIAL OUTPUT SWING (mVP-P)
TA = 85°C
TA = 85°C
TA = 25°C
24
TA = –40°C
20
2.5
3.5
4.5
SUPPLY VOLTAGE (V)
5.5
5502 G01
TA = 25°C
800
TA = –40°C
600
400
1.8
VCC = 3V
fIF = 280MHz
1000
1000
28
16
1.8
(Note 3)
I/Q Output Swing vs Temperature
1200
36
2.5
mA
Note 3: Tests are performed as shown in the configuration of Figure 3.
Note 4: Tests are performed as shown in the configuration of Figure 1 for
IF input.
TYPICAL PERFOR A CE CHARACTERISTICS
Power Supply Current
vs Temperature
V
25
Note 1: Absolute Maximum Ratings are those values beyond which the life
a device may be impaired.
Note 2: Specifications over the –40°C to 85°C temperature range are
assured by design, characterization and correlation with statistical process
controls.
32
5.25
3.5
4.5
SUPPLY VOLTAGE (V)
5.5
5502 G02
TA = 85°C
TA = 25°C
800
600
TA = –40°C
400
200
–85
–70
–55 –40
–25
–10
IF INPUT POWER (dBm)
5
5502 G03
3
LT5502
U W
TYPICAL PERFOR A CE CHARACTERISTICS (Note 3)
I/Q Output Swing vs IF Input Power
VCC = 3V
TA = 25°C
1.2
VCC = 3V
fIF = 280MHz
800
fIF = 280MHz
600
0.8
TA = 85°C
TA = –40°C
0.6
TA = 25°C
0.8
fIF = 70MHz
0.6
0.4
0.4
–55
–40
–25
–10
IF INPUT POWER (dBm)
0.2
–85
5
–70
–55
–40
–25
–10
IF INPUT POWER (dBm)
–73
INPUT SENSITIVITY (dBm)
1.0
0.8
VCC = 3V
0.6
VCC = 5.5V
VCC = 1.8V
0.4
–55
–40
–25
–10
IF INPUT POWER (dBm)
fIF = 280MHz
–75
TA = 85°C
–77
TA = 25°C
–79
TA = –40°C
–81
–83
1.8
5
2.5
4.5
SUPPLY VOLTAGE (V)
5
110
0
VCC = 3V
TA = –40°C
–82
70 100
150 200 250 300
IF FREQUENCY (MHz)
350
TA = –40°C
65
TA = 25°C
50
110
VCC = 1.8V, 3V, 5.5V
TA = 25°C
0
TA = 85°C
80
–5
90
–10
–15
70
–20
–25
35
–30
20
–35
0
4
8
16
12
BASEBAND FREQUENCY (MHz)
20
5502 G10
400
LPF Frequency Response vs VCC
5
–25
4
TA = –40°C
50
–30
0
4
8
12
16
BASEBAND FREQUENCY (MHz)
20
5502 G11
–35
0
4
8
16
12
BASEBAND FREQUENCY (MHz)
30
20
5502 G12
GROUP DELAY (ns)
GROUP DELAY (ns)
–5
–20
TA = 25°C
5502 G09
95
TA = 85°C
–15
–79
5.5
LPF Group Delay
vs Baseband Frequency
TA = 25°C
TA = 85°C
5502 G08
VCC = 3V
–10
VCC = 3V
–76
–85
3.5
5502 G07
LPF Frequency Response
vs Baseband Frequency
5
IF Input Sensitivity vs IF Frequency
–73
GAIN RESPONSE (dB)
–70
–55 –40
–25
–10
IF INPUT POWER (dBm)
5502 G06
IF Input Sensitivity
vs Temperature
fIF = 280MHz
TA = 25°C
0.2
–85
–70
5502 G05
RSSI Output Voltage vs VCC
1.2
0.2
–85
5
INPUT SENSITIVITY (dBm)
–70
fIF = 400MHz
5502 G04
RSSI OUTPUT (V)
fIF = 280MHz
fIF = 400MHz
400
200
–85
GAIN RESPONSE (dB)
VCC = 3V
TA = 25°C
1.0
1.0
fIF = 70MHz
RSSI OUTPUT (V)
1000
RSSI Output Voltage vs IF Frequency
RSSI Output vs Temperature
1.2
RSSI OUTPUT (V)
DIFFERENTIAL OUTPUT SWING (mVP-P)
1200
LT5502
U
U
U
PI FU CTIO S
IOUT+ (Pin 1): Positive Baseband Output Pin of I-Channel.
The DC bias voltage is VCC – 1.16V. This pin should not be
shorted to ground.
IOUT– (Pin 2): Negative Baseband Input Pin of I-Channel.
The DC bias voltage is VCC – 1.16V. This pin should not be
shorted to ground.
GND (Pins 3, 5, 8, 9, 14, 20, 21): Ground Pin.
VCC (Pins 4, 16, 17, 22): Power Supply Pin. This pin
should be decoupled using 1000pF and 0.1µF capacitors.
IF + (Pin 6): Positive IF Input Pin. The DC bias voltage is
VCC – 0.4V.
IF – (Pin 7): Negative IF Input Pin. The DC bias voltage is
VCC – 0.4V.
voltage. When the input voltage is less than 0.7V or down
to ground, it is turned off.
IFt + (Pin 12): Interstage IF Positive Pin. The DC bias
voltage is VCC – 0.25V.
IFt – (Pin 13): Interstage IF Negative Pin. The DC bias
voltage is VCC – 0.25V.
RSSI (Pin 15): RSSI Output Pin.
2XLO – (Pin 18): Negative Carrier Input Pin. The inputsignal’s frequency must be twice that of the desired
demodulator LO frequency. The DC bias voltage is VCC –
0.4V.
2XLO + (Pin 19): Positive Carrier Input Pin. The inputsignal’s frequency must be twice that of the desired
demodulator LO frequency. The DC bias voltage is VCC –
0.4V.
EN (Pin 10): Enable Pin. When the input voltage is higher
than 0.9V or up to VCC, the circuit is completely turned on.
When the input voltage is less than 0.7V or down to
ground, the circuit is turned off except the part of the
circuit associated with standby mode.
QOUT– (Pin 23): Negative Baseband Output Pin of the
Q-Channel. The DC bias voltage is VCC – 1.16V. This pin
should not be shorted to ground.
STBY (Pin 11): Standby Pin. When the input voltage is
higher than 0.9V or up to VCC, the circuit of standby mode
is turned on to bias the I/Q buffers to desired quiescent
QOUT+ (Pin 24): Positive Baseband Output Pin of the
Q-Channel. The DC bias voltage is VCC – 1.16V. This pin
should not be shorted to ground.
W
BLOCK DIAGRA
IFt+
IFt–
12
13
I-MIXER
6
IF –
7
1
IOUT+
2
IOUT–
1
LIMITER
2
LIMITER
1
IF +
LPF
LO
BUFFERS
DIVIDE 2
0°/90°
LPF
24 QOUT+
1
RSSI
23 QOUT–
Q-MIXER
BIAS
15
RSSI
19
2XLO +
18
2XLO –
10
EN
5502 BD
5
LT5502
U
W
U
U
APPLICATIO S I FOR ATIO
The LT5502 consists of the following sections: IF limiter,
I/Q demodulators, quadrature LO carrier generator, integrated lowpass filters (LPFs), and bias circuitry.
An IF signal is fed to the inputs of the IF limiter. The limited
IF signal is then demodulated into I/Q baseband signals
using the quadrature LO carriers that are generated from
the divide-by-two circuit. The demodulated I/Q signals are
passed through 5th order LPFs and buffered with an
output driver.
The 1:4 IF input transformer can also be replaced with a
narrow band single-to-differential conversion circuit
using three discreet elements as shown in Figure 1. Their
nominal values are listed in Table 1. Due to the parasitics
of the PCB, their values need to be compensated. The
receiver’s input sensitivity in this case is improved to
–85dBm even without interstage filtering. The matching
circuit is essentially a second order bandpass filter. Therefore, the requirement for the front-end channel-select
filter can be eased too.
IF Limiter
The IF limiter has 84dB small-signal gain with a frequency
range of 70MHz to 400MHz. It consists of two cascaded
stages of IF amplifiers/limiters. The differential outputs of
the first stage are connected internally to the differential
inputs of the second stage. An interstage filtering is
possible in between (Pin 12 and Pin 13) with minimum offchip components. It can be a simple parallel LC tank circuit
L1 and C8 as shown in Figure 3. The 22nF blocking
capacitor, C19, is used for the proper operation of the
internal DC offset canceling circuit. To achieve the best
receiver sensitivity, a differential configuration at the IF
input is recommended due to its better immunity to 2XLO
signal coupling to the IF limiter. Otherwise, the 2XLO
interference, presented at the IF inputs, may saturate the
IF limiter and reduce the gain of the wanted IF signal. The
receiver’s 3dB input-limiting sensitivity will be affected
correspondingly. The interstage bandpass filter will minimize both 2XLO feedthrough and the receiver’s noise
bandwidth. Therefore, the receiver’s input sensitivity can
be improved. Without the interstage filter, the second
stage will be limited by the broadband noise amplified by
the first stage. The noise bandwidth in this case can be as
high as 500MHz. The 3dB input limiting sensitivity is about
–79dBm at an IF frequency of 280MHz when terminated
with 200Ω at the input. The differential IF input impedance
is 2.2kΩ. Therefore, a 240Ω resistor is used for R3 as
shown in Figure 3. Using a bandpass filter with 50MHz
bandwidth, the input sensitivity is improved to –86dBm.
6
MATCHING NETWORK
CS1
3.3pF
IF
INPUT
C5
22nF
TO IF +
CS2
3.3pF
LSH
120nH
TO IF –
5502 F01
Figure 1. IF Input Matching Network at 280MHz
Table 1. The Component Values of Matching Network
LSH, CS1 and CS2
fIF (MHz)
LSH (nH)
CS1/CS2 (pF)
70
642
13.7
100
422
9.6
150
256
6.4
200
176
4.8
250
130
3.8
300
101
3.2
350
80.4
2.7
400
66.0
2.4
In an application where a lower input sensitivity is satisfactory, one of the IF inputs can be simply AC-terminated with
a 50Ω resistor and the other AC-grounded. The input
receiver’s sensitivity is about – 76dBm at 280MHz in this
case.
LT5502
U
W
U
U
APPLICATIO S I FOR ATIO
The receive signal strength indicator (RSSI) is built into
the IF limiter. The input IF signal is detected in a current
output proportional to the IF input power. The current
outputs from two cascaded stages of IF amplifiers/limiters
are summed and converted into the RSSI voltage. The
RSSI output has an excellent linear range of 90dB. The
characteristic of RSSI output voltage versus input IF
power is independent of temperature and process variation. The nominal output impedance is 3.8kΩ. An off-chip
capacitor C7 is needed to reduce the RSSI voltage ripple.
Its value can be determined using the following formula:
C7 ≥
1
F
760π • fIF
matched in gain response and group delay. The 3dB
corner frequency is 7.7MHz and the group delay ripple is
16.4ns. The I/Q differential outputs have output driving
capability of 1.5kΩ with maximum capacitive loading of
10pF. The outputs are internally biased at VCC –1.16V.
Figure 2 shows the simplified output circuit schematic of
I-channel or Q-channnel.
VCC
I-CHANNEL
(OR Q-CHANNEL):
DIFFERENTIAL
SIGNALS FROM LPF
IOUT+
(OR QOUT+)
IOUT–
(OR QOUT–)
I/Q Demodulators
The quadrature demodulators are double balanced mixers, down converting the limited IF signals from the IF
Limiter into I/Q baseband signals. The quadrature LO
carriers are obtained from the internal quadrature LO
carrier generator. The nominal output voltage of differential I/Q baseband signals is about 850mVP-P. These magnitudes are well matched, and their phases are 90° apart.
Quadrature LO Carrier Generator
The quadrature LO carrier generator consists of a divideby-two circuit and LO buffers. An input signal (2XLO) with
twice the desired LO carrier frequency is used as the clock
for the divide-by-two circuit, producing the quadrature LO
carriers for the demodulators. The outputs are buffered
and then drive the down converting mixers. With a full
differential approach, the quadrature LO carriers are well
matched.
Integrated Low Pass Filters
The 5th order integrated lowpass filters are used for
filtering the down converted baseband outputs for both
the I-channel and the Q-channel. They serve as antialiasing and pulse-shaping filters. The I/Q filters are well
+
+
200µA
–
200µA
–
5502 F02
Figure 2. Simplified Circuit Schematic
of I-Channel (or Q-Channel) Outputs
The I/Q baseband outputs can be directly DC-coupled to
the inputs of a baseband chip. For AC-coupled applications with large coupling capacitors, the STBY pin can be
used to prebias the outputs to the desired quiescent
voltage at much reduced current. This mode only draws
2.6mA. When the EN pin is then turned on, the chip is
quickly switched to normal operating mode without long
time constants due to charging or discharging the large
coupling capacitors. Table 2 shows the logic of the EN pin
and STBY pin. In both normal operating mode and standby
mode, the maximum discharging current is about 200µA,
and the maximum charging current is more than 10mA.
Table 2. The logic of different operating modes
EN
STBY
Comments
Low
Low
Shutdown Mode
Low
High
Standby Mode
High
Low or High
Normal Operation Mode
7
LT5502
U
TYPICAL APPLICATIO S
IOUT+
R8
51.1k
J2
R7
49.9
+
U2
LT1809CS
6
IOUT
–
4
R10
5.11k
J1
IFIN
C24
10µF
C25
10µF
C20
1µF
C14
1µF
VCC1
C1
1µF
2
R6
2.55k C11
1µF
C12
1.8pF
C5
22nF
R2
20k
1
2
3
4
5
6
7
8
9
10
11
12
IOUT+
IOUT–
C2
1nF
R12
C15 2.55k
1µF
U1
LT5502
GND
VCC
GND
IF +
IF –
GND
GND
EN
STBY
IFt +
2
÷2
QOUT+
QOUT–
VCC
GND
GND
2XLO+
2XLO –
VCC
VCC
RSSI
GND
IFt –
24
23
22
21
20
19
18
17
16
15
14
13
VCC2
C23
1µF
R1
20k
–
6
R16
49.9
4
R13
5.11k
6
RSSI
C18
1µF
L1
5502 F02
Figure 3. Evaluation Circuit Schematic With I/Q Output Buffers
J3
QOUT
R4
240Ω
C19
22nF
8
C17
1µF
U3
LT1809CS
T2
JTX-4-10T
C4
1nF
IF INTERSTAGE R17
OPTIONAL CIRCUIT
7
+
C16
1.8pF
C3
1nF
C8
SW1
R15
51.1k
3
1:4
MINI-CIRCUIT
1 = EN
2 = STBY
R14
51.1k
3
T1
JTX-4-10T
6
1
R3
240Ω
C9
1µF
R9
51.1k
QOUT+ QOUT–
VCC2
C10
1µF
7
C13
1µF
IOUT–
C7
1.8pF
1
4:1
MINI-CIRCUIT
J4
2XLO
LT5502
U
TYPICAL APPLICATIO S
Figure 4.Component Side Silkscreen of Evaluation Board
Figure 5. Component Side Layout of Evaluation Board
9
LT5502
U
TYPICAL APPLICATIO S
Figure 6.Bottom Side Silkscreen of Evaluation Board
Figure 7. Bottom Side Layout of Evaluation Board
10
LT5502
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
GN Package
24-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
0.337 – 0.344*
(8.560 – 8.738)
24 23 22 21 20 19 18 17 16 15 1413
0.229 – 0.244
(5.817 – 6.198)
0.150 – 0.157**
(3.810 – 3.988)
1
0.015 ± 0.004
× 45°
(0.38 ± 0.10)
0.007 – 0.0098
(0.178 – 0.249)
0.033
(0.838)
REF
2 3
4
5 6
7
8
0.053 – 0.068
(1.351 – 1.727)
9 10 11 12
0.004 – 0.0098
(0.102 – 0.249)
0° – 8° TYP
0.016 – 0.050
(0.406 – 1.270)
* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
0.008 – 0.012
(0.203 – 0.305)
0.0250
(0.635)
BSC
GN24 (SSOP) 1098
11
LT5502
U
TYPICAL APPLICATIO
Example: 2.4GHz to 2.5GHz Receiver Application (RX IF = 280MHz)
2V
100pF
0.1µF
12
RX INPUT:
2.4GHz TO
2.5GHz
280MHz IF
SAW BP
FILTER
3.3pF
RX
FRONT END
1st LO,
2.12GHz
TO 2.22GHz
VCC 4,16,17,22
13
I
1 OUTPUTS
2
I MIXER
22nF
6
7
LIMITER
1
LIMITER
2
LO
BUFFER
90°
LPF
Q MIXER
LPF
3.3pF
11
10
19
1nF
1.8pF
IF
SYNTHESIZER
A/D
BUFFER
STBY
EN
LT5502
18
3,5,8,9,
14,20,21
1nF
BUFFER
Q
24 OUTPUTS
23
f/2
RSSI 15
A/D
0°
120nH
MAIN
SYNTHESIZER
BASEBAND
PROCESSOR
2.7pF
30nH
2nd LO,
560MHz
200Ω
30nH
2.7pF
5502 TA02
12
Linear Technology Corporation
5502i LT/TP 0101 2K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 2001