MAXIM DS1307

DS1307
64 x 8, Serial, I C Real-Time Clock
2
GENERAL DESCRIPTION
FEATURES
The DS1307 serial real-time clock (RTC) is a
low-power, full binary-coded decimal (BCD)
clock/calendar plus 56 bytes of NV SRAM.
Address and data are transferred serially through
an I2C, bidirectional bus. The clock/calendar
provides seconds, minutes, hours, day, date,
month, and year information. The end of the
month date is automatically adjusted for months
with fewer than 31 days, including corrections for
leap year. The clock operates in either the 24hour or 12-hour format with AM/PM indicator.
The DS1307 has a built-in power-sense circuit
that detects power failures and automatically
switches to the backup supply. Timekeeping
operation continues while the part operates from
the backup supply.
Real-Time Clock (RTC) Counts Seconds,
Minutes, Hours, Date of the Month, Month,
Day of the week, and Year with Leap-Year
Compensation Valid Up to 2100
56-Byte, Battery-Backed, Nonvolatile (NV)
RAM for Data Storage
I2C Serial Interface
Programmable Square-Wave Output Signal
Automatic Power-Fail Detect and Switch
Circuitry
Consumes Less than 500nA in BatteryBackup Mode with Oscillator Running
Optional Industrial Temperature Range:
-40°C to +85°C
Available in 8-Pin Plastic DIP or SO
Underwriters Laboratory (UL) Recognized
Typical Operating Circuit and Pin Configurations appear
at end of data sheet.
ORDERING INFORMATION
PART
DS1307
DS1307+
DS1307N
DS1307N+
DS1307Z
DS1307Z+
DS1307ZN
DS1307ZN+
DS1307Z/T&R
DS1307Z+T&R
DS1307ZN/T&R
DS1307ZN+T&R
TEMP RANGE
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
VOLTAGE
(V)
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
PIN-PACKAGE
TOP MARK*
8 PDIP (300 mils)
8 PDIP (300 mils)
8 PDIP (300 mils)
8 PDIP (300 mils)
8 SO (150 mils)
8 SO (150 mils)
8 SO (150 mils)
8 SO (150 mils)
8 SO (150 mils) Tape and Reel
8 SO (150 mils) Tape and Reel
8 SO (150 mils) Tape and Reel
8 SO (150 mils) Tape and Reel
DS1307
DS1307
DS1307N
DS1307N
DS1307
DS1307
DS1307N
DS1307N
DS1307
DS1307
DS1307N
DS1307N
+ Denotes a lead-free/RoHS-compliant device.
* A “+” anywhere on the top mark indicates a lead-free device.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 15
REV: 121906
DS1307 64 x 8, Serial, I2C Real-Time Clock
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin Relative to Ground……….……………………….…………....-0.5V to +7.0V
Operating Temperature Range (Noncondensing)
Commercial…………………….……………………………….………………………..0°C to +70°C
Industrial………………………………………………………………………………-40°C to +85°C
Storage Temperature Range………………………………………...…………..…………-55°C to +125°C
Soldering Temperature (DIP, leads)..…………………………………………….....+260°C for 10 seconds
Soldering Temperature (surface mount)…..…………………………See JPC/JEDEC Standard J-STD-020
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is
not implied. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability.
RECOMMENDED DC OPERATING CONDITIONS
(TA = 0°C to +70°C, TA = -40°C to +85°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.0
5.5
V
Supply Voltage
VCC
4.5
Logic 1 Input
VIH
2.2
VCC + 0.3
V
Logic 0 Input
VIL
-0.3
+0.8
V
VBAT
2.0
3.5
V
VBAT Battery Voltage
3
DC ELECTRICAL CHARACTERISTICS
(VCC = 4.5V to 5.5V; TA = 0°C to +70°C, TA = -40°C to +85°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Input Leakage (SCL)
ILI
-1
1
µA
I/O Leakage (SDA, SQW/OUT)
ILO
-1
1
µA
Logic 0 Output (IOL = 5mA)
Active Supply Current
(fSCL = 100kHz)
Standby Current
VOL
0.4
V
ICCA
1.5
mA
200
µA
5
50
nA
1.25 x
VBAT
1.284 x
VBAT
V
TYP
MAX
UNITS
IBAT1
300
500
nA
IBAT2
480
800
nA
IBATDR
10
100
nA
VBAT Leakage Current
Power-Fail Voltage (VBAT = 3.0V)
ICCS
(Note 3)
IBATLKG
1.216 x
VBAT
VPF
DC ELECTRICAL CHARACTERISTICS
(VCC = 0V, VBAT = 3.0V; TA = 0°C to +70°C, TA = -40°C to +85°C.) (Notes 1, 2)
PARAMETER
VBAT Current (OSC ON);
SQW/OUT OFF
VBAT Current (OSC ON);
SQW/OUT ON (32kHz)
VBAT Data-Retention Current
(Oscillator Off)
SYMBOL
CONDITIONS
MIN
WARNING: Negative undershoots below -0.3V while the part is in battery-backed mode may cause loss of data.
2 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
AC ELECTRICAL CHARACTERISTICS
(VCC = 4.5V to 5.5V; TA = 0°C to +70°C, TA = -40°C to +85°C.)
PARAMETER
SYMBOL
SCL Clock Frequency
Bus Free Time Between a STOP and
START Condition
Hold Time (Repeated) START
Condition
LOW Period of SCL Clock
fSCL
0
tBUF
4.7
µs
4.0
µs
tLOW
4.7
µs
tHIGH
4.0
µs
tHD:STA
CONDITIONS
(Note 4)
MIN
TYP
MAX
UNITS
100
kHz
HIGH Period of SCL Clock
Setup Time for a Repeated START
Condition
Data Hold Time
tSU:STA
4.7
µs
tHD:DAT
0
µs
Data Setup Time
tSU:DAT
250
ns
Rise Time of Both SDA and SCL
Signals
Fall Time of Both SDA and SCL
Signals
Setup Time for STOP Condition
(Notes 5, 6)
tR
1000
ns
tF
300
ns
tSU:STO
µs
4.7
CAPACITANCE
(TA = +25°C)
PARAMETER
SYMBOL
Pin Capacitance (SDA, SCL)
CI/O
Capacitance Load for Each Bus
Line
CB
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
CONDITIONS
(Note 7)
MIN
TYP
MAX
UNITS
10
pF
400
pF
All voltages are referenced to ground.
Limits at -40°C are guaranteed by design and are not production tested.
ICCS specified with VCC = 5.0V and SDA, SCL = 5.0V.
After this period, the first clock pulse is generated.
A device must internally provide a hold time of at least 300ns for the SDA signal (referred to the VIH(MIN) of the
SCL signal) to bridge the undefined region of the falling edge of SCL.
The maximum tHD:DAT only has to be met if the device does not stretch the LOW period (tLOW) of the SCL signal.
CB—total capacitance of one bus line in pF.
3 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
TIMING DIAGRAM
SDA
tBUF
tLOW
tR
tHD:STA
tF
SCL
tHD:STA
STOP
tSU:STA
tHIGH
START
tSU:STO
SU:DAT
REPEATED
START
tHD:DAT
Figure 1. Block Diagram
X1
1Hz/4.096kHz/8.192kHz/32.768kHz
CL
MUX/
BUFFER
1Hz
X2
CL
Oscillator
and divider
VCC
GND
POWER
CONTROL
RAM
(56 X 8)
CONTROL
LOGIC
VBAT
Dallas
Semiconductor
DS1307
SCL
SDA
SERIAL BUS
INTERFACE
AND ADDRESS
REGISTER
CLOCK,
CALENDAR,
AND CONTROL
REGISTERS
USER BUFFER
(7 BYTES)
4 of 15
SQW/OUT
DS1307 64 x 8, Serial, I2C Real-Time Clock
TYPICAL OPERATING CHARACTERISTICS
(VCC = 5.0V, TA = +25°C, unless otherwise noted.)
ICCS vs. VCC
IBAT vs. VBAT
V BAT=3.0V
V CC = 0V
400
120
SQW=32kHz
110
350
100
SUPPLY CURRENT (uA)
SUPPLY CURRENT (nA)
90
300
80
70
250
60
50
SQW off
200
40
30
150
20
10
100
0
1.0
2.0
3.0
VCC (V)
4.0
IBAT vs. Temperature
2.0
5.0
2.5
V CC=0V, V BAT=3.0
VBACKUP (V)
3.0
3.5
SQW/OUT vs. Supply Voltage
32769
32768.9
SQW=32kHz
325.0
32768.7
FREQUENCY (Hz)
SUPPLY CURRENT (nA)
32768.8
275.0
225.0
32768.6
32768.5
32768.4
32768.3
32768.2
SQW off
32768.1
175.0
-40
-20
0
20
40
60
32768
80
2.0
TEMPERATURE (°C)
5 of 15
2.5
3.0
3.5
4.0
Supply (V)
4.5
5.0
5.5
DS1307 64 x 8, Serial, I2C Real-Time Clock
PIN DESCRIPTION
PIN
NAME
1
X1
2
X2
3
VBAT
FUNCTION
Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator circuitry is
designed for operation with a crystal having a specified load capacitance (CL) of 12.5pF.
X1 is the input to the oscillator and can optionally be connected to an external 32.768kHz
oscillator. The output of the internal oscillator, X2, is floated if an external oscillator is
connected to X1.
Note: For more information on crystal selection and crystal layout considerations, refer to
Application Note 58: Crystal Considerations with Dallas Real-Time Clocks.
Backup Supply Input for Any Standard 3V Lithium Cell or Other Energy Source. Battery
voltage must be held between the minimum and maximum limits for proper operation.
Diodes in series between the battery and the VBAT pin may prevent proper operation. If a
backup supply is not required, VBAT must be grounded. The nominal power-fail trip point
(VPF) voltage at which access to the RTC and user RAM is denied is set by the internal
circuitry as 1.25 x VBAT nominal. A lithium battery with 48mAhr or greater will back up
the DS1307 for more than 10 years in the absence of power at +25°C.
UL recognized to ensure against reverse charging current when used with a lithium
battery. Go to: www.maxim-ic.com/qa/info/ul/.
4
GND
Ground
5
SDA
Serial Data Input/Output. SDA is the data input/output for the I2C serial interface. The
SDA pin is open drain and requires an external pullup resistor.
6
SCL
Serial Clock Input. SCL is the clock input for the I2C interface and is used to synchronize
data movement on the serial interface.
SWQ/OUT
Square Wave/Output Driver. When enabled, the SQWE bit set to 1, the SQW/OUT pin
outputs one of four square-wave frequencies (1Hz, 4kHz, 8kHz, 32kHz). The SQW/OUT
pin is open drain and requires an external pullup resistor. SQW/OUT operates with either
VCC or VBAT applied.
VCC
Primary Power Supply. When voltage is applied within normal limits, the device is fully
accessible and data can be written and read. When a backup supply is connected to the
device and VCC is below VTP, read and writes are inhibited. However, the timekeeping
function continues unaffected by the lower input voltage.
7
8
DETAILED DESCRIPTION
The DS1307 is a low-power clock/calendar with 56 bytes of battery-backed SRAM. The clock/calendar
provides seconds, minutes, hours, day, date, month, and year information. The date at the end of the
month is automatically adjusted for months with fewer than 31 days, including corrections for leap year.
The DS1307 operates as a slave device on the I2C bus. Access is obtained by implementing a START
condition and providing a device identification code followed by a register address. Subsequent registers
can be accessed sequentially until a STOP condition is executed. When VCC falls below 1.25 x VBAT, the
device terminates an access in progress and resets the device address counter. Inputs to the device will not
be recognized at this time to prevent erroneous data from being written to the device from an out-oftolerance system. When VCC falls below VBAT, the device switches into a low-current battery-backup
mode. Upon power-up, the device switches from battery to VCC when VCC is greater than VBAT +0.2V and
recognizes inputs when VCC is greater than 1.25 x VBAT. The block diagram in Figure 1 shows the main
elements of the serial RTC.
6 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
OSCILLATOR CIRCUIT
The DS1307 uses an external 32.768kHz crystal. The oscillator circuit does not require any external
resistors or capacitors to operate. Table 1 specifies several crystal parameters for the external crystal.
Figure 1. shows a functional schematic of the oscillator circuit. If using a crystal with the specified
characteristics, the startup time is usually less than one second.
CLOCK ACCURACY
The accuracy of the clock is dependent upon the accuracy of the crystal and the accuracy of the match
between the capacitive load of the oscillator circuit and the capacitive load for which the crystal was
trimmed. Additional error will be added by crystal frequency drift caused by temperature shifts. External
circuit noise coupled into the oscillator circuit may result in the clock running fast. Refer to Application
Note 58: Crystal Considerations with Dallas Real-Time Clocks for detailed information.
Table 1. Crystal Specifications*
PARAMETER
Nominal Frequency
Series Resistance
Load Capacitance
SYMBOL
fO
ESR
CL
MIN
TYP
32.768
MAX
45
12.5
UNITS
kHz
kΩ
pF
*The crystal, traces, and crystal input pins should be isolated from RF generating signals. Refer to
Application Note 58: Crystal Considerations for Dallas Real-Time Clocks for additional specifications.
Figure 2. Recommended Layout for Crystal
LOCAL GROUND PLANE (LAYER 2)
X1
CRYSTAL
X2
GND
NOTE: AVOID ROUTING SIGNAL LINES IN THE CROSSHATCHED
AREA (UPPER LEFT QUADRANT) OF THE PACKAGE UNLESS
THERE IS A GROUND PLANE BETWEEN THE SIGNAL LINE AND THE
DEVICE PACKAGE.
RTC AND RAM ADDRESS MAP
Table 2 shows the address map for the DS1307 RTC and RAM registers. The RTC registers are located in
address locations 00h to 07h. The RAM registers are located in address locations 08h to 3Fh. During a
multibyte access, when the address pointer reaches 3Fh, the end of RAM space, it wraps around to
location 00h, the beginning of the clock space.
7 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
CLOCK AND CALENDAR
The time and calendar information is obtained by reading the appropriate register bytes. Table 2 shows
the RTC registers. The time and calendar are set or initialized by writing the appropriate register bytes.
The contents of the time and calendar registers are in the BCD format. The day-of-week register
increments at midnight. Values that correspond to the day of week are user-defined but must be
sequential (i.e., if 1 equals Sunday, then 2 equals Monday, and so on.) Illogical time and date entries
result in undefined operation. Bit 7 of Register 0 is the clock halt (CH) bit. When this bit is set to 1, the
oscillator is disabled. When cleared to 0, the oscillator is enabled.
Note that the initial power-on state of all registers is not defined. Therefore, it is important to
enable the oscillator (CH bit = 0) during initial configuration.
The DS1307 can be run in either 12-hour or 24-hour mode. Bit 6 of the hours register is defined as the
12-hour or 24-hour mode-select bit. When high, the 12-hour mode is selected. In the 12-hour mode, bit 5
is the AM/PM bit with logic high being PM. In the 24-hour mode, bit 5 is the second 10-hour bit (20 to
23 hours). The hours value must be re-entered whenever the 12/24-hour mode bit is changed.
When reading or writing the time and date registers, secondary (user) buffers are used to prevent errors
when the internal registers update. When reading the time and date registers, the user buffers are
synchronized to the internal registers on any I2C START. The time information is read from these
secondary registers while the clock continues to run. This eliminates the need to re-read the registers in
case the internal registers update during a read. The divider chain is reset whenever the seconds register is
written. Write transfers occur on the I2C acknowledge from the DS1307. Once the divider chain is reset,
to avoid rollover issues, the remaining time and date registers must be written within one second.
Table 2. Timekeeper Registers
ADDRESS
00H
01H
BIT 7
CH
0
02H
0
03H
04H
0
0
05H
0
06H
07H
OUT
BIT 6
BIT 5
BIT 4
10 Seconds
10 Minutes
10
12
10
Hour
Hour
PM/
24
AM
0
0
0
0
10 Date
10
0
0
Month
10 Year
0
0
SQWE
BIT 3
BIT 2 BIT 1
Seconds
Minutes
0
BIT 0
FUNCTION
Seconds
Minutes
RANGE
00–59
00–59
Hours
Hours
1–12
+AM/PM
00–23
DAY
Date
Day
Date
01–07
01–31
Month
01–12
Year
Control
RAM
56 x 8
00–99
—
Month
Year
0
08H-3FH
0 = Always reads back as 0.
8 of 15
0
RS1
RS0
00H–FFH
DS1307 64 x 8, Serial, I2C Real-Time Clock
CONTROL REGISTER
The DS1307 control register is used to control the operation of the SQW/OUT pin.
BIT 7
OUT
BIT 6
0
BIT 5
0
BIT 4
SQWE
BIT 3
0
BIT 2
0
BIT 1
RS1
BIT 0
RS0
Bit 7: Output Control (OUT). This bit controls the output level of the SQW/OUT pin when the squarewave output is disabled. If SQWE = 0, the logic level on the SQW/OUT pin is 1 if OUT = 1 and is 0 if
OUT = 0.
Bit 4: Square-Wave Enable (SQWE). This bit, when set to logic 1, enables the oscillator output. The
frequency of the square-wave output depends upon the value of the RS0 and RS1 bits. With the squarewave output set to 1Hz, the clock registers update on the falling edge of the square wave.
Bits 1, 0: Rate Select (RS1, RS0). These bits control the frequency of the square-wave output when the
square-wave output has been enabled. The following table lists the square-wave frequencies that can be
selected with the RS bits.
RS1
0
0
1
1
X
X
RS0
0
1
0
1
X
X
SQW/OUT OUTPUT
1Hz
4.096kHz
8.192kHz
32.768kHz
0
1
SQWE
1
1
1
1
0
0
9 of 15
OUT
X
X
X
X
0
1
DS1307 64 x 8, Serial, I2C Real-Time Clock
I2C DATA BUS
The DS1307 supports the I2C protocol. A device that sends data onto the bus is defined as a transmitter
and a device receiving data as a receiver. The device that controls the message is called a master. The
devices that are controlled by the master are referred to as slaves. The bus must be controlled by a master
device that generates the serial clock (SCL), controls the bus access, and generates the START and STOP
conditions. The DS1307 operates as a slave on the I2C bus.
Figures 3, 4, and 5 detail how data is transferred on the I2C bus.
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in
the data line while the clock line is high will be interpreted as control signals.
Accordingly, the following bus conditions have been defined:
Bus not busy: Both data and clock lines remain HIGH.
Start data transfer: A change in the state of the data line, from HIGH to LOW, while the clock is
HIGH, defines a START condition.
Stop data transfer: A change in the state of the data line, from LOW to HIGH, while the clock line
is HIGH, defines the STOP condition.
Data valid: The state of the data line represents valid data when, after a START condition, the data
line is stable for the duration of the HIGH period of the clock signal. The data on the line must be
changed during the LOW period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The
number of data bytes transferred between START and STOP conditions is not limited, and is
determined by the master device. The information is transferred byte-wise and each receiver
acknowledges with a ninth bit. Within the I2C bus specifications a standard mode (100kHz clock
rate) and a fast mode (400kHz clock rate) are defined. The DS1307 operates in the standard mode
(100kHz) only.
Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after
the reception of each byte. The master device must generate an extra clock pulse which is associated
with this acknowledge bit.
A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in
such a way that the SDA line is stable LOW during the HIGH period of the acknowledge related
clock pulse. Of course, setup and hold times must be taken into account. A master must signal an
end of data to the slave by not generating an acknowledge bit on the last byte that has been clocked
out of the slave. In this case, the slave must leave the data line HIGH to enable the master to generate
the STOP condition.
10 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
Figure 3. Data Transfer on I2C Serial Bus
SDA
MSB
R/W
DIRECTION
BIT
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SCL
1
START
CONDITION
2
6
7
8
9
1
ACK
2
3-7
8
9
ACK
REPEATED IF MORE BYTES
ARE TRANSFERED
STOP
CONDITION
OR
REPEATED
START
CONDITION
Depending upon the state of the R/W bit, two types of data transfer are possible:
1. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the
master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge
bit after each received byte. Data is transferred with the most significant bit (MSB) first.
2. Data transfer from a slave transmitter to a master receiver. The first byte (the slave address) is
transmitted by the master. The slave then returns an acknowledge bit. This is followed by the slave
transmitting a number of data bytes. The master returns an acknowledge bit after all received bytes
other than the last byte. At the end of the last received byte, a “not acknowledge” is returned.
The master device generates all the serial clock pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a repeated START condition. Since a repeated
START condition is also the beginning of the next serial transfer, the bus will not be released. Data is
transferred with the most significant bit (MSB) first.
11 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
The DS1307 may operate in the following two modes:
1. Slave Receiver Mode (Write Mode): Serial data and clock are received through SDA and
SCL. After each byte is received an acknowledge bit is transmitted. START and STOP
conditions are recognized as the beginning and end of a serial transfer. Hardware performs
address recognition after reception of the slave address and direction bit (see Figure 4). The
slave address byte is the first byte received after the master generates the START condition.
The slave address byte contains the 7-bit DS1307 address, which is 1101000, followed by the
direction bit (R/W), which for a write is 0. After receiving and decoding the slave address
byte, the DS1307 outputs an acknowledge on SDA. After the DS1307 acknowledges the slave
address + write bit, the master transmits a word address to the DS1307. This sets the register
pointer on the DS1307, with the DS1307 acknowledging the transfer. The master can then
transmit zero or more bytes of data with the DS1307 acknowledging each byte received. The
register pointer automatically increments after each data byte are written. The master will
generate a STOP condition to terminate the data write.
2. Slave Transmitter Mode (Read Mode): The first byte is received and handled as in the slave
receiver mode. However, in this mode, the direction bit will indicate that the transfer direction
is reversed. The DS1307 transmits serial data on SDA while the serial clock is input on SCL.
START and STOP conditions are recognized as the beginning and end of a serial transfer (see
Figure 5). The slave address byte is the first byte received after the START condition is
generated by the master. The slave address byte contains the 7-bit DS1307 address, which is
1101000, followed by the direction bit (R/W), which is 1 for a read. After receiving and
decoding the slave address the DS1307 outputs an acknowledge on SDA. The DS1307 then
begins to transmit data starting with the register address pointed to by the register pointer. If
the register pointer is not written to before the initiation of a read mode the first address that is
read is the last one stored in the register pointer. The register pointer automatically increments
after each byte are read. The DS1307 must receive a Not Acknowledge to end a read.
<Slave Address>
S
1101000
<RW>
Figure 4. Data Write—Slave Receiver Mode
0
<Word Address (n)>
A XXXXXXXX
<Data(n)>
A XXXXXXXX
<Data(n+1)>
A XXXXXXXX
<Data(n+X)>
A ... XXXXXXXX
A P
Master to slave
S - Start
A - Acknowledge (ACK)
P - Stop
DATA TRANSFERRED
(X+1 BYTES + ACKNOWLEDGE)
Slave to master
<Slave Address>
S
1101000
<RW>
Figure 5. Data Read—Slave Transmitter Mode
1
<Data(n)>
<Data(n+1)>
A XXXXXXXX
S - Start
A - Acknowledge (ACK)
P - Stop
A - Not Acknowledge (NACK)
A XXXXXXXX
Master to slave
Slave to master
<Data(n+2)>
A XXXXXXXX
<Data(n+X)>
A ... XXXXXXXX
A P
DATA TRANSFERRED
(X+1 BYTES + ACKNOWLEDGE); NOTE: LAST DATA BYTE IS
FOLLOWED BY A NOT ACKNOWLEDGE (A) SIGNAL)
12 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
<Slave Address>
S
1101000
0
<Word Address (n)>
A XXXXXXXX
<Data(n)>
XXXXXXXX
<Slave Address>
A Sr
<Data(n+1)>
A XXXXXXXX
S - Start
Sr - Repeated Start
A - Acknowledge (ACK)
P - Stop
A - Not Acknowledge (NACK)
<RW>
<RW>
Figure 6. Data Read (Write Pointer, Then Read)—Slave Receive and Transmit
1
1101000
<Data(n+2)>
<Data(n+X)>
A XXXXXXXX
Master to slave
A
A ... XXXXXXXX
A P
DATA TRANSFERRED
(X+1 BYTES + ACKNOWLEDGE); NOTE: LAST DATA BYTE IS
FOLLOWED BY A NOT ACKNOWLEDGE (A) SIGNAL)
Slave to master
TYPICAL OPERATING CIRCUIT
VCC
VCC
CRYSTAL
VCC
RPU
RPU
X1
X2
SQW/OUT
SCL
CPU
VCC
DS1307
SDA
VBAT
GND
RPU = tr/Cb
PIN CONFIGURATIONS
1
X2
VBAT
2
GND
4
3
8
VCC
7
SQW/OUT
6
5
X1
1
8
VCC
7
SQW/OUT
SCL
X2
VBAT
2
6
SCL
SDA
GND
4
5
SDA
PDIP (300 mils)
3
DS1307
X1
DS1307
TOP VIEW
SO (150 mils)
13 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
PACKAGE INFORMATION
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package
outline information, go to www.maxim-ic.com/DallasPackInfo.)
14 of 15
DS1307 64 x 8, Serial, I2C Real-Time Clock
PACKAGE INFORMATION (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package
outline information, go to www.maxim-ic.com/DallasPackInfo.)
15 of 15
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.