AD ADN4600ACPZ

4.25 Gbps, 8 × 8,
Asynchronous Crosspoint Switch
ADN4600
FEATURES
FUNCTIONAL BLOCK DIAGRAM
ADN4600
RECEIVE
EQUALIZATION
CROSSPOINT
ARRAY
TRANSMIT
PRE-EMPHASIS
IP[7:0]
OP[7:0]
EQ
PE
ON[7:0]
IN[7:0]
ADDR[1:0]
SCL
SDA
CONTROL LOGIC
RESETB
07061-001
Full 8 × 8 crossbar connectivity
Fully buffered signal path supports multicast and broadcast
operation
Optimized for dc to 4.25 Gbps data
Programmable receive equalization
Compensates for up to 30 in. of FR4 @ 4.25 Gbps
Programmable transmit pre-emphasis/de-emphasis
Compensates for up to 30 in. of FR4 @ 4.25 Gbps
Flexible 1.8 V to 3.3 V core supply
Per lane positive/negative (P/N) pair inversion for routing ease
Low power: 125 mW/channel at 4.25 Gbps
DC- or ac-coupled differential CML inputs
Programmable CML output levels
50 Ω on-chip termination
−40°C to +85°C temperature range operation
Supports 8b10b, scrambled or uncoded nonreturn-to-zero
(NRZ) data
I2C control interface
Package: 64-lead LFCSP
Figure 1.
APPLICATIONS
1×, 2×, 4× FibreChannel
XAUI
Gigabit Ethernet over backplane
10GBase-CX4
InfiniBand®
50 Ω cables
GENERAL DESCRIPTION
The ADN4600 is an asynchronous, nonblocking crosspoint
switch with eight differential PECL-/CML-compatible inputs
with programmable equalization and eight differential CML
outputs with programmable output levels and pre-emphasis or
de-emphasis. The operation of this device is optimized for NRZ
data at rates up to 4.25 Gbps.
The receive inputs provide programmable equalization with
nine settings to compensate for up to 30 in. of FR4 and
programmable pre-emphasis with seven settings to compensate
for up to 30 in. of FR4 at 4.25 Gbps.
The ADN4600 nonblocking switch core implements an 8 × 8
crossbar and supports independent channel switching through the
I2C control interface. Every channel implements an asynchronous
path supporting NRZ data rates from dc to 4.25 Gbps. Each
channel is fully independent of other channels. The ADN4600
has low latency and very low channel-to-channel skew.
The main application for the ADN4600 is to support switching
on the backplane, line card, or cable interface sides of serial links.
The ADN4600 is packaged in a 9 mm × 9 mm, 64-lead LFCSP
package and operates from −40°C to +85°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
ADN4600
TABLE OF CONTENTS
Features .............................................................................................. 1 Typical Performance Characteristics ..............................................8 Applications ....................................................................................... 1 Theory of Operation ...................................................................... 13 Functional Block Diagram .............................................................. 1 Introduction ................................................................................ 13 General Description ......................................................................... 1 Receivers ...................................................................................... 13 Revision History ............................................................................... 2 Switch Core ................................................................................. 15 Specifications..................................................................................... 3 Transmitters ................................................................................ 16 Electrical Specifications ............................................................... 3 I2C Control Interface.................................................................. 22 Timing Specifications .................................................................. 5 PCB Design Guidelines ............................................................. 24 Absolute Maximum Ratings............................................................ 6 Control Register Map ..................................................................... 25 ESD Caution .................................................................................. 6 Package Outline Dimensions ........................................................ 28 Pin Configuration and Function Descriptions ............................. 7 Ordering Guide .......................................................................... 28 REVISION HISTORY
6/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 2
ADN4600
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
VCC = 1.8 V, VEE = 0 V, VTTI = VTTO = VCC, RL = 50 Ω, differential output swing = 800 mV p-p differential, 4.25 Gbps, PRBS 27 − 1,
TA = 25°C, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
Maximum Data Rate per Channel
Deterministic Jitter
Random Jitter
Residual Deterministic Jitter with
Receive Equalization
Residual Deterministic Jitter with
Transmit Pre-Emphasis
Output Rise/Fall Time
Channel-to-Channel Skew
Propagation Delay
OUTPUT PRE-EMPHASIS
Equalization Method
Maximum Boost
Pre-Emphasis Tap Range
INPUT EQUALIZATION
Minimum Boost
Maximum Boost
Number of Equalization Steps
Gain Step Size
INPUT CHARACTERISTICS
Input Voltage Swing
Input Voltage Range
Input Resistance
Input Return Loss
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Voltage Range
Output Current
Output Resistance
Output Return Loss
Conditions
Min
In NRZ format
Data rate < 4.25 Gbps; BER = 1e − 12
VCC = 1.8 V
Data rate < 3.25 Gbps; 0 in. to 30 in. FR4
Data rate < 4.25 Gbps; 0 in. to 30 in. FR4
Data rate < 3.25 Gbps; 0 in. to 30 in. FR4
Data rate < 4.25 Gbps; 0 in. to 30 in. FR4
20% to 80%
4.25
One-tap programmable pre-emphasis
800 mV p-p output swing
200 mV p-p output swing
Minimum
Maximum
EQBY = 1
Maximum boost occurs @ 2.125 GHz
Differential, VICM 1 = VCC − 0.6 V; VCC = 3.3 V
Single-ended absolute voltage level, VL minimum
Single-ended absolute voltage level, VH maximum
Single-ended
Measured at 2.5 GHz
@ dc, differential, PE = 0, default, VCC = 1.8 V
@ dc, differential, PE = 0, default, VCC = 3.3 V
@ dc, differential, PE = 0, min output level 2 , VCC = 1.8 V
@ dc, differential, PE = 0, min output level2, VCC = 3.3 V
@ dc, differential, PE = 0, max output level2, VCC = 1.8 V
@ dc, differential, PE = 0, max output level2, VCC = 3.3 V
Single-ended absolute voltage level,
TxHeadroom = 0; VL min
Single-ended absolute voltage level,
TxHeadroom = 0; VH max
Single-ended absolute voltage level,
TxHeadroom = 1; VL min
Single-ended absolute voltage level,
TxHeadroom = 1; VH max
Minimum output current per channel
Maximum output current per channel, VCC = 1.8 V
Single ended
Measured at 2.5 GHz
Rev. 0 | Page 3 of 3
Typ
635
45
Unit
30
1.5
0.16
0.20
0.13
0.18
75
50
1
Gbps
ps p-p
ps rms
UI
UI
UI
UI
ps
ps
ns
6
12
2
12
dB
dB
mA
mA
1.5
22
8
2.5
dB
dB
Steps
dB
300
45
Max
2000
VEE + 0.4
VCC + 0.5
50
5
740
800
100
100
1300
1800
VCC − 1.1
55
870
mV p-p
V p-p
V p-p
Ω
dB
mV p-p
mV p-p
mV p-p
mV p-p
mV p-p
mV p-p
V
VCC + 0.6
V
VCC − 1.2
V
VCC + 0.6
V
2
21
50
5
mA
55
Ω
dB
ADN4600
Parameter
POWER SUPPLY
Operating Range
VCC
DVCC
VTTI
VTTO
Supply Current 3
ITTO
ICC
IEE
ITTO
ICC
IEE
LOGIC CHARACTERISTICS
Input High (VIH)
Input Low (VIL)
Output High (VOH)
Output Low (VOL)
THERMAL CHARACTERISTICS
Operating Temperature Range
θJA
1
2
3
Conditions
Min
Typ
Max
Unit
VEE = 0 V
VEE = 0 V, DVCC ≤ (VCC + 1.3 V)
(VEE + 0.4 V + 0.5 × VID) < VTTI < (VCC + 0.5 V)
1.7
3.0
VEE +
0.4
VCC −
1.1
1.8
3.3
1.8
3.6
3.6
3.6
V
V
V
1.8
3.6
V
63
460
586
16
173
205
69
565
mA
mA
mA
mA
mA
mA
(VCC − 1.1 V + 0.5 × VOD) < VTTO < (VCC + 0.5 V)
All outputs enabled
All outputs enabled
All outputs enabled
Single channel enabled
Single channel enabled
Single channel enabled
DVCC = 3.3 V
18
214
2.5
1.0
2.5
1.0
−40
+85
22
VICM is the input common-mode voltage.
Programmable via I2C.
Assumes dc-coupled outputs. For ac-coupled outputs, ITTO currents will double.
Rev. 0 | Page 4 of 4
V
V
V
V
°C
°C/W
ADN4600
TIMING SPECIFICATIONS
Table 2. I2C Timing Parameters
Parameter
fSCL
tHD;STA
tSU;STA
tLOW
tHIGH
tHD;DAT
tSU;DAT
tr
tf
tSU;STO
tBUF
CIO
Min
0
0.6
0.6
1.3
0.6
0
10
1
1
0.6
1
5
Max
400
N/A
N/A
N/A
N/A
N/A
N/A
300
300
N/A
N/A
7
Unit
kHz
μs
μs
μs
μs
μs
ns
ns
ns
μs
ns
Pf
Description
SCL clock frequency
Hold time for a start condition
Setup time for a repeated start condition
Low period of the SCL clock
High period of the SCL clock
Data hold time
Data setup time
Rise time for both SDA and SCL
Fall time for both SDA and SCL
Setup time for a stop condition
Bus-free time between a stop and a start condition
Capacitance for each I/O pin
I2C Timing Specifications
SDA
tSU:DAT
tf
tLOW
tf
tHD:STA
tf
tBUF
tf
tHD:STA
S
tHD:DAT
tHIGH
tSU:STA
tSU:STO
Sr
Figure 2. I2C Timing Diagram
Rev. 0 | Page 5 of 5
P
S
07061-010
SCL
ADN4600
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
VCC to VEE
VTTI
VTTO
Internal Power Dissipation
Differential Input Voltage
Logic Input Voltage
Storage Temperature Range
Lead Temperature
Rating
3.7 V
VCC + 0.6 V
VCC + 0.6 V
4.26 W
2.0 V
VEE − 0.3 V < VIN < VCC + 0.6 V
−65°C to +125°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Rev. 0 | Page 6 of 6
ADN4600
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
VEE
VCC
VEE
OP0
ON0
VCC
OP1
ON1
VTTO
OP2
ON2
VEE
OP3
ON3
ADDR1
ADDR0
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
ADN4600
TOP VIEW
(Not to Scale)
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
SCL
SDA
VEE
IP7
IN7
VCC
IP6
IN6
VTTI
IP5
IN5
VEE
IP4
IN4
VCC
VEE
VEE
VCC
ON7
OP7
VCC
ON6
OP6
VTTO
ON5
OP5
VEE
ON4
OP4
VEE
VCC
VEE
NOTES
1. PAD ON BOTTOM OF PACKAGE MUST BE CONNECTED TO VEE.
07061-002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
RESETB
VEE
IN0
IP0
VCC
IN1
IP1
VTTI
IN2
IP2
VEE
IN3
IP3
DVCC
VCC
VEE
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
2, 11, 16, 17, 27,
30, 32, 33, 37,
46, 53, 62, 64
3, 6, 9, 12, 35,
38, 41, 44
4, 7, 10, 13, 36,
39, 42, 45
5, 15, 18, 21, 31,
34, 43, 59, 63
8, 40
14
19, 22, 25, 28,
51, 54, 57, 60
20, 23, 26, 29,
52, 55, 58, 61
24, 56
47
48
49
50
Mnemonic
RESETB
VEE
Type
Control
Power
Description
Reset Input (Active Low)
Negative Supply
IN0 to IN7
I/O
High Speed Inputs
IP0 to IP7
I/O
High Speed Input Complements
VCC
Power
Positive Supply
VTTI
DVCC
ON7 to ON0
Power
Power
I/O
Input Termination Supply
Digital Positive Supply (3.3 V)
High Speed Outputs
OP7 to ON0
I/O
High Speed Output Complements
VTTO
SDA
SCL
ADDR0
ADDR1
EPAD
Power
Control
Control
Control
Control
Power
Output Termination Supply
I2C Control Interface Data Input/Output
I2C Control Interface Clock Input
I2C Control Interface Address LSB
I2C Control Interface Address MSB
Connect to VEE
Rev. 0 | Page 7 of 7
ADN4600
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 5 to Figure 8 were obtained using the standard test circuit shown in Figure 4.
2
50Ω CABLES
PATTERN
GENERATOR
2
INPUT
PIN
OUTPUT 2
PIN
50Ω CABLES
2
50Ω
ADN4600
AC-COUPLED
EVALUATION
BOARD
TP1
TP2
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07061-011
DATA OUT
50ps/DIV
50ps/DIV
Figure 6. 4.25 Gbps Input Eye
(TP1 from Figure 4)
Figure 8. 4.25 Gbps Output Eye, No Channel
(TP2 from Figure 4)
Rev. 0 | Page 8 of 8
07061-015
50ps/DIV
07061-013
200mV/DIV
Figure 7. 3.25 Gbps Output Eye, No Channel
(TP2 from Figure 4)
200mV/DIV
Figure 5. 3.25 Gbps Input Eye
(TP1 from Figure 4)
07061-014
200mV/DIV
50ps/DIV
07061-012
200mV/DIV
Figure 4. Standard Test Circuit (No Channel)
ADN4600
Figure 10 to Figure 13 were obtained using the standard test circuit shown in Figure 9.
2
DATA OUT
50Ω CABLES
2
50Ω CABLES
2
2
DIFFERENTIAL
STRIPLINE TRACES
TP1
8mils WIDE, 8mils SPACE,
8mils DIELECTRIC HEIGHT
TRACE LENGTHS = 30''
INPUT OUTPUT 2
PIN
PIN
50Ω CABLES
2
50Ω
ADN4600
TP2
AC-COUPLED
EVALUATION
BOARD
TP3
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07061-016
PATTERN
GENERATOR
FR4 TEST BACKPLANE
50ps/DIV
50ps/DIV
07061-020
50ps/DIV
Figure 11. 4.25 Gbps Input Eye, 30 Inch FR4 Input Channel
(TP2 from Figure 9)
07061-018
200mV/DIV
Figure 12. 3.25 Gbps Output Eye, 30 Inch FR4 Input Channel, Best EQ Setting
(TP3 from Figure 9)
200mV/DIV
Figure 10. 3.25 Gbps Input Eye, 30 Inch FR4 Input Channel
(TP2 from Figure 9)
07061-019
200mV/DIV
50ps/DIV
07061-017
200mV/DIV
Figure 9. Input Equalization Test Circuit, FR4 (See Figure 5 and Figure 6 for the Reference Eye Diagrams at TP1)
Figure 13. 4.25 Gbps Output Eye, 30 Inch FR4 Input Channel, Best EQ Setting
(TP3 from Figure 9)
Rev. 0 | Page 9 of 9
ADN4600
Figure 15 to Figure 18 were obtained using the standard test circuit shown in Figure 14.
2
DATA OUT
50Ω CABLES
2
ADN4600
TP1
FR4 TEST BACKPLANE
2
50Ω
DIFFERENTIAL
STRIPLINE TRACES
TP2
8mils WIDE, 8mils SPACE,
8mils DIELECTRIC HEIGHT
TRACE LENGTHS = 30''
AC-COUPLED
EVALUATION
BOARD
50Ω CABLES
2
TP3
HIGH SPEED
SAMPLING
OSCILLOSCOPE
07061-021
PATTERN
GENERATOR
50Ω CABLES
2
INPUT OUTPUT 2
PIN
PIN
50ps/DIV
50ps/DIV
Figure 16. 4.25 Gbps Output Eye, 30 Inch FR4 Output Channel, PE = 0
(TP3 from Figure 14)
07061-025
50ps/DIV
07061-023
200mV/DIV
Figure 17. 3.25 Gbps Output Eye, 30 Inch FR4 Output Channel, PE = Best Setting
(TP3 from Figure 14)
200mV/DIV
Figure 15. 3.25 Gbps Output Eye, 30 Inch FR4 Output Channel, PE = 0
(TP3 from Figure 14)
07061-024
200mV/DIV
50ps/DIV
07061-022
200mV/DIV
Figure 14. Output Pre-Emphasis Test Circuit, FR4
Figure 18. 4.25 Gbps Output Eye, 30 Inch FR4 Output Channel, PE = Best Setting
(TP3 from Figure 14)
Rev. 0 | Page 10 of 10
ADN4600
Test conditions: VCC = 1.8 V, VEE = 0 V, VTTI = VTTO = VCC, RL = 50 Ω, differential output swing = 800 mV p-p differential, TA = 25°C,
unless otherwise noted.
100
80
DETERMINISTIC JITTER (ps)
DETERMINISTIC JITTER (ps)
70
60
50
40
30
20
80
60
VCC = 3.3V
40
VCC = 1.8V
20
0
20
60
40
DATA RATE (Hz)
0
1.0
07061-026
0
Figure 19. Deterministic Jitter vs. Data Rate
1.5
2.0
2.5
3.0
INPUT COMMON MODE (V)
3.5
4.0
07061-029
10
Figure 22. Deterministic Jitter vs. Input Common Mode
100
100
80
DETERMINISTIC JITTER (ps)
DETERMINISTIC JITTER (ps)
90
70
60
50
40
30
20
80
60
40
20
0.5
1.0
1.5
2.0
DIFFERENTIAL INPUT SWING (V)
2.5
0
1.0
100
80
80
DETERMINISTIC JITTER (ps)
100
60
40
20
0
–60
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
2.0
2.5
VCC (V)
3.0
3.5
4.0
Figure 23. Deterministic Jitter vs. Supply Voltage
100
60
VCC = 1.8V
40
VCC = 3.3V
20
0
1.0
07061-028
DETERMINISTIC JITTER (ps)
Figure 20. Deterministic Jitter vs. Input Swing
1.5
Figure 21. Deterministic Jitter vs. Temperature
1.5
2.0
2.5
VTTO (V)
3.0
3.5
4.0
Figure 24. Deterministic Jitter vs. Output Termination Voltage
Rev. 0 | Page 11 of 11
07061-031
0
07061-027
0
07061-030
10
ADN4600
450000
100
400000
90
300000
tR/tF (ps)
250000
200000
80
tR/tF
70
150000
100000
60
0
–8
–6
–4
–2
0
2
JITTER (ps)
4
6
8
10
50
–60
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
Figure 26. Rise Time/Fall Time vs. Temperature
Figure 25. Random Jitter Histogram
Rev. 0 | Page 12 of 12
100
07061-033
50000
07061-032
NUMBER OF SAMPLES
350000
ADN4600
THEORY OF OPERATION
inversion function, which allows the user to swap the sign of the
input signal path to eliminate the need for board-level
crossovers in the receiver channel.
INTRODUCTION
The ADN4600 is an 8 × 8, buffered, asynchronous, 8-channel
crosspoint switch that allows fully nonblocking connectivity
between its transmitters and receivers. The switch supports
multicast and broadcast operation, allowing the ADN4600 to
work in redundancy and port-replication applications.
Table 5 illustrates some, but not all, possible combinations of
input supply voltages.
Equalization Settings
ADN4600
RECEIVE
EQUALIZATION
CROSSPOINT
ARRAY
TRANSMIT
PRE-EMPHASIS
IP[7:0]
OP[7:0]
EQ
PE
ON[7:0]
IN[7:0]
ADDR[1:0]
SCL
SDA
CONTROL LOGIC
07061-003
RESETB
Figure 27. Simplified Functional Block Diagram
The ADN4600 offers extensively programmable output levels
and pre-emphasis, as well as a squelch function and the ability
to fully disable the device. The receivers integrate a programmable,
multizero transfer function that has been optimized to compensate
either typical backplane or typical cable losses. The ADN4600
provides a balanced, high speed switch core that maintains low
channel-to-channel skew and preserves edge rates.
The I/O on-chip termination resistors are tied to user-settable
supplies to support dc coupling in various logic styles. The
ADN4600 supports a wide core supply range; VCC can be set
from 1.8 V to 3.3 V. These features together with programmable
transmitter output levels allow for several dc- and ac-coupled
I/O configurations.
RECEIVERS
Input Structure and Input Levels
VCC
SIMPLIFIED RECEIVER INPUT CIRCUIT
VTTI
RP
52Ω
IPx
INx
RN
52Ω
RLN
RL
R1
750Ω
RLP
RL
Q1
R3
1kΩ
Q2
R2
750Ω
07061-004
I1
VEE
Figure 28. Simplified Input Structure
The ADN4600 receiver inputs incorporate 50 Ω termination
resistors, ESD protection, and a multizero transfer function
equalizer that can be optimized for backplane and cable operation.
Each receive channel also provides a positive/negative (P/N)
The ADN4600 receiver incorporates a multizero transfer
function with a continuous time equalizer, providing up to
22 dB of high-frequency boost at 2.25 GHz to compensate for
up to 30 in. of FR4 at 4.25 Gbps. The ADN4600 also allows
independent control of the equalizer transfer function on each
channel through the I2C control interface.
In the basic mode of operation, the equalizer transfer function
allows independent control of the boost in two frequency ranges
for optimal matching with the loss shape of the channel (for
example, the shape due primarily to skin effect or to dielectric
loss). The total equalizer shape space is reduced to two independent
frequency response groups—one optimized for cable and the
other optimized for FR4 material. The RX EQ bits of the
RX[7:0] configuration registers provide eight settings for each
frequency response group to ease programming for typical
channels.
Table 6 summarizes the high-frequency boost for the frequency
response grouping optimized for the FR4 material; it lists the basic
control settings and the typical length of FR4 trace compensated
for by each setting. All eight channels of the ADN4600 use the
FR4-optimized frequency response grouping by default. The
user can override this default by setting the respective RX LUT
select bit high and then selecting the frequency response grouping
by setting the RX LUT FR4/CX4 bit high for FR4 and low for
cable. Setting the RX EQBY bit of the RX[7:0] configuration
registers high sets the equalization to 1.5 dB of boost, which
compensates for 0 m to 2 m of CX4 or 0 in. to 10 in. of FR4.
In the advanced mode of operation, full control of the equalizer is
available through the I2C control interface. The user can specify
the boost in the midfrequency range and the boost in the high
frequency range independently. This is accomplished by
circumventing the frequency response groupings shown in
Table 6 by setting the EQ CTL SRC bit (Bit 6 of the RX[7:0]
EQ1 control registers) high and writing directly to the equalizer
control bits on a per channel basis. Therefore, write values to
Bits[5:0] of the RX[7:0] EQ1 control registers and to Bits[5:0]
of the RX[7:0] EQ3 control registers for the channel of interest.
The bits of these registers are ordered such that Bit 5 is a sign
bit, and midlevel boost is centered around 0x00. Setting Bit 5
low and increasing the LSBs decreases the boost, whereas
setting Bit 5 high and increasing the LSBs increases the boost.
Rev. 0 | Page 13 of 13
ADN4600
Table 5. Common Input Voltage Levels
Configuration
Low VTTI, AC-Coupled Input
Single 1.8 V Supply
3.3 V Core
Single 3.3 V Supply
VCC (V)
1.8
1.8
3.3
3.3
VTTI (V)
1.6
1.8
1.8
3.3
Table 6. Receive Equalizer Boost vs. Setting
RX EQ Bit Settings
0
1
2
3
4
5
6
7
Boost (dB)
3.5
3.9
4.25
4.5
4.75
5.0
5.3
5.5
Typical FR4 Trace Length (Inches)
5 to 10
10 to 15
15 to 20
20 to 25
25 to 30
30 to 35
35 to 40
35 to 40
Table 7. Equalization Control Registers
Name
RX[7:0] Configuration
RX[7:0] EQ1 Control
RX[7:0] EQ3 Control
RX[7:0] FR4 Control
Addr
0xB8, 0xB0,
0xA8, 0xA0,
0x98, 0x90,
0x88, 0x80
0xBB, 0xB3,
0xAB, 0xA3,
0x9B, 0x93,
0x8B, 0x83
0xBC, 0xB4,
0xAC, 0xA4,
0x9C, 0x94,
0x8C, 0x84
0xBD, 0xB5,
0xAD, 0xA5,
0x9D, 0x95,
0x8D, 0x85
Bit 7
Bit 6
RX PNSWAP
Bit 5
RX EQBY
Bit 4
RX EN
Bit 3
Bit 2
RX EQ[2]
Bit 1
RX EQ[1]
Bit 0
RX EQ[0]
Default
0x30
EQ CTL SRC
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX EQ1[1]
RX EQ1[0]
0x00
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
select
RX LUT
FR4/CX4
0x00
Lane Inversion
The receiver P/N inversion feature is a convenience intended to
allow the user to implement the equivalent of a board-level
crossover in a much smaller area and without additional via
impedance discontinuities that degrade the high-frequency
integrity of the signal path. The P/N inversion is independent
for each of the eight channels and is controlled through the I2C
control interface.
Warning
Using the lane inversion feature to account for signal inversions
downstream of the receiver requires additional attention when
switching connectivity.
Rev. 0 | Page 14 of 14
ADN4600
SWITCH CORE
The ADN4600 switch core is a fully nonblocking 8 × 8 array
that allows multicast and broadcast configurations. The
configuration of the switch core is controlled through the I2C
control interface. The control interface receives and stores the
desired connection matrix for the eight input and eight output
signal pairs. The interface consists of eight rows of double-rank
latches, one for each output. The 2-bit data-word stored in these
latches indicates to which (if any) of the eight inputs the output
will be connected.
One output at a time can be preprogrammed by addressing the
output and writing the desired connection data into the first rank
of latches. This is done by writing to the XPT configuration
register (Address 0x40). The output being addressed is written
into Bits[2:0], and the input being sent to this output is written
into Bits[6:4]. This process can be repeated until each of the
desired output changes has been preprogrammed. Bit 3 of the
XPT configuration register (Address 0x40) signals whether a
broadcast condition is desired. If this bit is set high, the input
selected by Bits[6:4] is sent to all outputs. All output connections
can then be programmed simultaneously by passing the data
from the first rank of latches into the second rank by writing
0x01 to the XPT update register (Address 0x41). This is a selfclearing register and therefore always reads back as 0x00. The
output connections always reflect the data programmed into the
second rank of latches and do not change until the first rank of data
is passed into the second rank by strobing the XPT update register.
If necessary for system verification, the data in the first rank of
latches can be read back from the control interface. This is done
by reading from the XPT Temp[3:0] registers, which show the
status of the input data programmed in the first rank of latches
for each output.
Table 8. Switch Core Control and Status Registers
Name
XPT Configuration
Addr
0x40
XPT Update
XPT Status 0
XPT Status 1
XPT Status 2
XPT Status 3
XPT Status 4
XPT Status 5
XPT Status 6
XPT Status 7
0x41
0x50
0x51
0x52
0x53
0x54
0x55
0x56
0x57
Bit 7
Bit 6
IN PORT
[2]
Bit 5
IN PORT
[1]
Bit 4
IN PORT
[0]
Bit 3
Broadcast
Bit 2
OUT PORT
[2]
Bit 1
OUT PORT
[1]
Default
0x00
OUT0[1]
OUT1[1]
OUT2[1]
OUT3[1]
OUT4[1]
OUT5[1]
OUT6[1]
OUT7[1]
Bit 0
OUT PORT
[0]
Update
OUT0[0]
OUT1[0]
OUT2[0]
OUT3[0]
OUT4[0]
OUT5[0]
OUT6[0]
OUT7[0]
OUT0[2]
OUT1[2]
OUT2[2]
OUT3[2]
OUT4[2]
OUT5[2]
OUT6[2]
OUT7[2]
Bit 2
OUT0[2]
OUT2[2]
OUT4[2]
OUT6[2]
Bit 1
OUT0[1]
OUT2[1]
OUT4[1]
OUT6[1]
Bit 0
OUT0[0]
OUT2[0]
OUT4[0]
OUT6[0]
Default
N/A
N/A
N/A
N/A
0x00
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Table 9. Switch Core Temporary Registers
Name
XPT Temp 0
XPT Temp 1
XPT Temp 2
XPT Temp 3
Addr
0x58
0x59
0x5A
0x5B
Bit 7
Bit 6
OUT1[2]
OUT3[2]
OUT5[2]
OUT7[2]
Bit 5
OUT1[1]
OUT3[1]
OUT5[1]
OUT7[1]
Bit 4
OUT1[0]
OUT3[0]
OUT5[0]
OUT7[0]
Bit 3
Rev. 0 | Page 15 of 15
ADN4600
Output Structure and Output Levels
The ADN4600 transmitter outputs incorporate 50 Ω termination
resistors, ESD protection, and output current switch. Each
channel provides independent control of both the absolute
output level and the pre-emphasis output level. It should be
noted that the choice of output level affects the output commonmode level. A 600 mV p-p differential output level with full
pre-emphasis range requires an output termination voltage
of 2.5 V or greater; therefore, for the VTTO pin, VCC must be
equal to or greater than 2.5 V.
Pre-Emphasis
The output equalization is optimized for less than 2.5 Gbps
operation, but can be optimized for higher speed applications
up to 4.25 Gbps through the I2C control interface by writing to
the TX DATA RATE bit (Bit 4) of the TX[7:0] configuration
register, with high representing 4.25 Gbps and low representing
2.5 Gbps. The TX[7:0] CTL SRC bit (Bit 7) in the TX[7:0]
Output Level Control 1 register determines whether the preemphasis and output current controls for the channel of interest
are selected from the optimized map or directly from the
TX[7:0] Output Level Control[1:0] registers (per channel).
Setting this bit high selects pre-emphasis control directly from
the TX[7:0] Output Level Control[1:0] registers, and setting it
low selects pre-emphasis control from the optimized map.
TX SIMPLIFIED DIAGRAM
The total output amplitude and pre-emphasis setting space is
reduced to a single map of basic settings that provides seven
settings of output equalization to ease programming for typical
channels. The full resolution of seven settings is available through
the I2C interface by writing to Bits[2:0] (the TX PE[2:0] bits) of
the TX[7:0] configuration registers. Table 10 summarizes the
absolute output level, pre-emphasis level, and high frequency
boost for each of the control settings and the typical length of
FR4 trace compensated for by each setting.
VCC
ON-CHIP
TERMINATION
V3
VC
RP
52Ω
V2
VP
ESD
VTTO
RN
52Ω
OPx
V1
VN
ONx
Q1
Q2
Full control of the transmit output levels is available through the
I2C control interface. This full control is achieved by writing to
the TX[7:0] Output Level Control[1:0] registers for the channel
of interest. The supported output levels are shown in Table 12.
The TX[7:0] Output Level Control[1:0] registers must be
programmed to one of the supported settings listed in this table;
other settings are not supported.
IDC + TPE IT
VEE
07061-006
TRANSMITTERS
Figure 29. Simplified Output Structure
Table 10. Transmit Pre-Emphasis Boost and Overshoot vs. Setting
TX PE
0
1
2
3
4
5
6
Boost (dB)
0
2
3.5
4.9
6
7.4
9.5
Overshoot
0%
25%
50%
75%
100%
133%
200%
DC Swing (mV p-p Differential)
800
800
800
800
800
600
400
Typical FR4 Trace Length (Inches)
0 to 5
0 to 5
10 to 15
15 to 20
25 to 30
30 to 35
35 to 40
Table 11. Transmitters Control Registers
Name
TX[7:0]
Configuration
TX[7:0] Output
Level Control 1
TX[7:0] Output
Level Control 0
Addr
0xE0, 0xE8,
0xF0, 0xF8,
0xD8, 0xD0,
0xC8, 0xC0
0xE1, 0xE9,
0xF1, 0xF9,
0xD9, 0xD1,
0xC9, 0xC1
0xE2, 0xEA,
0xF2, 0xFA,
0xDA, 0xD2,
0xCA, 0xC2
Bit 7
Bit 6
Bit 5
TX EN
Bit 4
TX data
rate
TX[7:0]
CTL SRC
Rev. 0 | Page 16 of 16
Bit 3
Bit 2
TX PE[2]
Bit 1
TX PE[1]
Bit 0
TX PE[0]
Def.
0x20
TX[7:0]_OLEV1[6:0]
0x40
TX[7:0]_OLEV0[6:0]
0x40
ADN4600
Table 12. Output Level Programming
VOD (mV)
50
50
50
50
50
50
50
100
100
100
100
100
100
100
150
150
150
150
150
150
150
200
200
200
200
200
200
200
250
250
250
250
250
250
250
300
300
300
300
300
300
300
350
350
350
350
350
350
350
400
400
400
VD Peak (mV)
50
150
250
350
450
550
650
100
200
300
400
500
600
700
150
250
350
450
550
650
750
200
300
400
500
600
700
800
250
350
450
550
650
750
850
300
400
500
600
700
800
900
350
450
550
650
750
850
950
400
500
600
PE (dB)
0.00
9.54
13.98
16.90
19.08
20.83
22.28
0.00
6.02
9.54
12.04
13.98
15.56
16.90
0.00
4.44
7.36
9.54
11.29
12.74
13.98
0.00
3.52
6.02
7.96
9.54
10.88
12.04
0.00
2.92
5.11
6.85
8.30
9.54
10.63
0.00
2.50
4.44
6.02
7.36
8.52
9.54
0.00
2.18
3.93
5.38
6.62
7.71
8.67
0.00
1.94
3.52
ITOT (mA)
2
6
10
14
18
22
26
4
8
12
16
20
24
28
6
10
14
18
22
26
30
8
12
16
20
24
28
32
10
14
18
22
26
30
34
12
16
20
24
28
32
36
14
18
22
26
30
34
38
16
20
24
Tx[7:0] Output Level Control 0
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
Rev. 0 | Page 17 of 17
Tx[7:0] Output Level Control 1
0x81
0x81
0x81
0x81
0x81
0x81
0x81
0x91
0x91
0x91
0x91
0x91
0x91
0x91
0x92
0x92
0x92
0x92
0x92
0x92
0x92
0xA2
0xA2
0xA2
0xA2
0xA2
0xA2
0xA2
0xA3
0xA3
0xA3
0xA3
0xA3
0xA3
0xA3
0xB3
0xB3
0xB3
0xB3
0xB3
0xB3
0xB3
0xB4
0xB4
0xB4
0xB4
0xB4
0xB4
0xB4
0xC4
0xC4
0xC4
ADN4600
VOD (mV)
400
400
400
400
450
450
450
450
450
450
450
500
500
500
500
500
500
500
550
550
550
550
550
550
550
600
600
600
600
600
600
600
650
650
650
650
650
650
700
700
700
700
700
750
750
750
750
800
800
800
850
850
900
VD Peak (mV)
700
800
900
1000
450
550
650
750
850
950
1050
500
600
700
800
900
1000
1100
550
650
750
850
950
1050
1150
600
700
800
900
1000
1100
1200
650
750
850
950
1050
1150
700
800
900
1000
1100
750
850
950
1050
800
900
1000
850
950
900
PE (dB)
4.86
6.02
7.04
7.96
0.00
1.74
3.19
4.44
5.52
6.49
7.36
0.00
1.58
2.92
4.08
5.11
6.02
6.85
0.00
1.45
2.69
3.78
4.75
5.62
6.41
0.00
1.34
2.50
3.52
4.44
5.26
6.02
0.00
1.24
2.33
3.30
4.17
4.96
0.00
1.16
2.18
3.10
3.93
0.00
1.09
2.05
2.92
0.00
1.02
1.94
0.00
0.97
0.00
ITOT (mA)
28
32
36
40
18
22
26
30
34
38
42
20
24
28
32
36
40
44
22
26
30
34
38
42
46
24
28
32
36
40
44
48
26
30
34
38
42
46
28
32
36
40
44
30
34
38
42
32
36
40
34
38
36
Tx[7:0] Output Level Control 0
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x00
0x11
0x22
0x33
0x44
0x55
0x66
0x01
0x12
0x23
0x34
0x45
0x56
0x02
0x13
0x24
0x35
0x46
0x03
0x14
0x25
0x36
0x04
0x15
0x26
0x05
0x16
0x06
Rev. 0 | Page 18 of 18
Tx[7:0] Output Level Control 1
0xC4
0xC4
0xC4
0xC4
0xC5
0xC5
0xC5
0xC5
0xC5
0xC5
0xC5
0xD5
0xD5
0xD5
0xD5
0xD5
0xD5
0xD5
0xD6
0xD6
0xD6
0xD6
0xD6
0xD6
0xD6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
0xE6
ADN4600
VTTO
High Current Setting and Output Level Shift
In low voltage applications, users must pay careful attention to
both the differential and common-mode signal levels (see Figure 30
and Table 13). Failure to understand the implications of signal
level and choice of ac or dc coupling will almost certainly lead
to transistor saturation and poor transmitter performance.
dVOCM
VH
VOD
VOCM
VL
TxHeadroom
There is a TxHeadroom register (I C Register Address 0x23)
that allows configuration of the individual transmitters for
extra headroom at the output for high current applications. The
bits in this register are active high (default). There is one bit for
each transmitter of the device (see Table 17). Setting this bit
high puts the respective transmitter in a configuration for extra
headroom, and setting this bit low does not provide extra
headroom.
VODPP = 2 × VOD
VEE
07061-007
2
Figure 30. Simplified Output Voltage Levels Diagram
Signal Levels and Common-Mode Shift for DC- and AC-Coupled Outputs
Table 13. Signal Levels and Common-Mode Shift for DC- and AC-Coupled Outputs
Output Levels and Output Compliance
AC-Coupled Transmitter
DC-Coupled Transmitter
VL
VL
Min
VD
VH
VH
Peak Peak dVOCM VH
Peak Peak VL
PE
dVOCM VH
VOD ITOT Peak PE
VL
VL
(V)
(V)
(V)
(mV) (mA) (mV) Boost (dB) (mV) (V) (V) (V)
(mV) (V) (V) (V)
TxHeadroom = 0
Max
Min
Min
VCC − VL VCC
VL
(V)
(V)
(V)
TxHeadroom = 1
Max
VCC − VL Min
(V)
VCC (V)
VTTO and VCC = 3.3 V
200 8
200 1.00
200 12
300 1.50
200 16
400 2.00
200 20
500 2.50
200 24
600 3.00
200 28
700 3.50
200 32
800 4.00
300 12
300 1.00
300 16
400 1.33
300 20
500 1.67
300 24
600 2.00
300 28
700 2.33
300 32
800 2.67
300 36
900 3.00
400 16
400 1.00
400 20
500 1.25
400 24
600 1.50
400 28
700 1.75
400 32
800 2.00
400 36
900 2.25
400 40
1000 2.50
600 24
600 1.00
600 28
700 1.17
600 32
800 1.33
600 36
900 1.50
600 40
1000 1.67
600 44
1200 1.83
600 48
1400 2.00
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
0.00
3.52
6.02
7.96
9.54
10.88
12.04
0.00
2.50
4.44
6.02
7.36
8.52
9.54
0.00
1.94
3.52
4.86
6.02
7.04
7.96
0.00
1.34
2.50
3.52
4.44
5.26
6.02
200
300
400
500
600
700
800
300
400
500
600
700
800
900
400
500
600
700
800
900
1000
600
700
800
900
1000
1100
1200
3.2
3.1
3
2.9
2.8
2.7
2.6
3.15
3.05
2.95
2.85
2.75
2.65
2.55
3.1
3
2.9
2.8
2.7
2.6
2.5
3
2.9
2.8
2.7
2.6
2.5
2.4
3
2.9
2.8
2.7
2.6
2.5
2.4
2.85
2.75
2.65
2.55
2.45
2.35
2.25
2.7
2.6
2.5
2.4
2.3
2.2
2.1
2.4
2.3
2.2
2.1
2
1.9
1.8
3.2
3.15
3.1
3.05
3
2.95
2.9
3.15
3.1
3.05
3
2.95
2.9
2.85
3.1
3.05
3
2.95
2.9
2.85
2.8
3
2.95
2.9
2.85
2.8
2.75
2.7
3
2.85
2.7
2.55
2.4
2.25
2.1
2.85
2.7
2.55
2.4
2.25
2.1
1.95
2.7
2.55
2.4
2.25
2.1
1.95
1.8
2.4
2.25
2.1
1.95
1.8
1.65
1.5
100
150
200
250
300
350
400
150
200
250
300
350
400
450
200
250
300
350
400
450
500
300
350
400
450
500
550
600
3.3
3.25
3.2
3.15
3.1
3.05
3
3.3
3.25
3.2
3.15
3.1
3.05
3
3.3
3.25
3.2
3.15
3.1
3.05
3
3.3
3.25
3.2
3.15
3.1
3.05
3
3.1
3.05
3
2.95
2.9
2.85
2.8
3
2.95
2.9
2.85
2.8
2.75
2.7
2.9
2.85
2.8
2.75
2.7
2.65
2.6
2.7
2.65
2.6
2.55
2.5
2.45
2.4
Rev. 0 | Page 19 of 19
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.1
3
2.9
2.8
2.7
2.6
2.5
3
2.9
2.8
2.7
2.6
2.5
2.4
2.9
2.8
2.7
2.6
2.5
2.4
2.3
2.7
2.6
2.5
2.4
2.3
2.2
2.1
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.225
2.1
2.225
2.225
2.225
2.225
2.1
2.1
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.2
2.2
2
2
2
2
2
2.2
2.2
2
2
2
2
2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
ADN4600
Output Levels and Output Compliance
AC-Coupled Transmitter
DC-Coupled Transmitter
VL
VL
Min
VD
VH
VH
Peak Peak dVOCM VH
Peak Peak VL
PE
dVOCM VH
VOD ITOT Peak PE
VL
VL
(V)
(V)
(V)
(mV) (mA) (mV) Boost (dB) (mV) (V) (V) (V)
(mV) (V) (V) (V)
TxHeadroom = 0
Max
Min
Min
VCC − VL VCC
VL
(V)
(V)
(V)
TxHeadroom = 1
Max
VCC − VL Min
(V)
VCC (V)
VTTO and VCC = 1.8 V 1
200 8
200 1.00
200 12
300 1.50
200 16
400 2.00
200 20
500 2.50
200 24
600 3.00
300 12
300 1.00
300 16
400 1.33
300 20
500 1.67
300 24
600 2.00
300 28
700 2.33
400 16
400 1.00
400 20
500 1.25
400 24
600 1.50
400 28
700 1.75
400 32
800 2.00
600 24
600 1.00
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
1
0.00
3.52
6.02
7.96
9.54
0.00
2.50
4.44
6.02
7.36
0.00
1.94
3.52
4.86
6.02
0.00
200
300
400
500
600
300
400
500
600
700
400
500
600
700
800
600
1.7
1.6
1.5
1.4
1.3
1.65
1.55
1.45
1.35
1.25
1.6
1.5
1.4
1.3
1.2
1.5
1.5
1.4
1.3
1.2
1.1
1.35
1.25
1.15
1.05
0.95
1.2
1.1
1
0.9
0.8
0.9
1.7
1.65
1.6
1.55
1.5
1.65
1.6
1.55
1.5
1.45
1.6
1.55
1.5
1.45
1.4
1.5
1.5
1.35
1.2
1.05
0.9
1.35
1.2
1.05
0.9
0.75
1.2
1.05
0.9
0.75
0.6
0.9
100
150
200
250
300
150
200
250
300
350
200
250
300
350
400
300
1.8
1.75
1.7
1.65
1.6
1.8
1.75
1.7
1.65
1.6
1.8
1.75
1.7
1.65
1.6
1.8
1.6
1.55
1.5
1.45
1.4
1.5
1.45
1.4
1.35
1.3
1.4
1.35
1.3
1.25
1.2
1.2
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.6
1.5
1.4
1.3
1.2
1.5
1.4
1.3
1.2
1.1
1.4
1.3
1.2
1.1
1
1.2
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.725
0.6
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.9
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
TxHeadroom = 1 is not an option at VTTO and VCC = 1.8 V.
Table 14. Symbol Definitions for Output Levels vs. Setting
Symbol
VOD
VODPP
dVOCM_DC-COUPLED
dVOCM_AC-COUPLED
IDC
IPE
Formula
25 Ω × IDC
25 Ω × IDC × 2 = 2 × VOD
25 Ω × ITX/2 = VODPP/4 + (IPE/2 × 25)
50 Ω × ITX/2 = VODPP/2 + (IPE/2 × 50)
VOD/RTERM
–
Definition
Peak differential output voltage
Peak-to-peak differential output voltage
Output common-mode shift
Output common-mode shift
Output current that sets output level
Output current used for PE
ITX
VH
VL
IDC + IPE
VTTO − dVOCM + VOD/2
VTTO − dVOCM − VOD/2
Total transmitter output current
Maximum single-ended output voltage
Minimum single-ended output voltage
Rev. 0 | Page 20 of 20
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
ADN4600
Selective Squelch and Disable
Each transmitter is equipped with disable and squelch controls.
Disable is a full power-down state: all transmitter current,
including output current, is reduced to 0 mA and the output
pins are pulled up to VTTO, but there is a delay of
approximately 1 μs associated with re-enabling the transmitter.
The output disable control is accessed through the TX EN bit
(Bit 5) of the TX[7:0] configuration registers through the I2C
control interface.
Squelch simply reduces the output current to submicroamp
levels, allowing both output pins to pull up to VTTO through
the output termination resistors. The transmitter recovers from
squelch in less than 100 ns.
The output squelch and the output disable control can both be
accessed through the TX[7:0] squelch control registers, with the
top nibble representing the squelch control and the bottom nibble
representing the output disable for one channel. The channels
are disabled or squelched by writing 0s to the corresponding
nibbles. The channels are enabled by writing all 1s, which is the
default setting. For example, to squelch channel TX0, Register
0xC3 must be set to 0x0F. The entire nibble must be written to
all 0s for this functionality.
Table 15. Transmitters Squelch Control Registers
Name
TX[7:0] Squelch Control
Addr
0xE3, 0xEB,
0xF3, 0xFB,
0xDB, 0xD3,
0xCB, 0xC3
Bit 7
Bit 6
Bit 5
SQUELCHb[3:0]
Bit 4
Rev. 0 | Page 21 of 21
Bit 3
Bit 2
Bit 1
DISABLEb[3:0]
Bit 0
Default
0xFF
ADN4600
I2C CONTROL INTERFACE
7.
Send the data (eight bits) to be written to the register
whose address was set in Step 5. This transfer should be
MSB first.
8. Wait for the ADN4600 to acknowledge the request.
9. Send a stop condition (that is, while holding the SCL line
high, pull the SDA line high) and release control of the bus.
10. Send a repeated start condition (that is, while holding the
SCL line high, pull the SDA line low) and continue with
Step 2 in this procedure to perform another write.
11. Send a repeated start condition (that is, while holding the
SCL line high, pull the SDA line low) and continue with
Step 2 of the read procedure (see the I2C Interface Data
Transfers: Data Read section) to perform a read from
another address.
12. Send a repeated start condition (that is, while holding the
SCL line high, pull the SDA line low) and continue with
Step 8 of the read procedure (in the I2C Interface Data
Transfers: Data Read section) to perform a read from the
same address set in Step 5 of the write procedure.
Serial Interface General Functionality
The ADN4600 register set is controlled through a 2-wire I2C
interface. The ADN4600 acts only as an I2C slave device. Therefore,
the I2C bus in the system needs to include an I2C master to
configure the ADN4600 and other I2C devices that may be on
the bus. Data transfers are controlled by the two I2C wires: the
SCL input clock pin and the SDA bidirectional data pin.
The ADN4600 I2C interface can be run in the standard (100 kHz)
and fast (400 kHz) modes. The SDA line only changes value
when the SCL pin is low, with two exceptions: the SDA pin is
driven low while the SCL pin is high to indicate the beginning
or continuation of a transfer, and the SDA line is driven high
while the SCL line is high to indicate the end of a transfer.
Therefore, it is important to control the SCL clock to toggle
only when the SDA line is stable, unless indicating a start,
repeated start, or stop condition.
I2C Interface Data Transfers: Data Write
To write data to the ADN4600 register set, a microcontroller
(or any other I2C master) needs to send the appropriate control
signals to the ADN4600 slave device. Use the following steps,
where the signals are controlled by the I2C master unless otherwise
specified. A diagram of the procedure is shown in Figure 31.
2.
3.
4.
5.
6.
Send a start condition (that is, while holding the SCL line
high, pull the SDA line low).
Send the ADN4600 part address (seven bits), whose upper
five bits are the static value b10010 and whose lower two
bits are controlled by the ADDR1 and ADDR0 input pins.
This transfer should be MSB first.
Send the write indicator bit (0).
Wait for the ADN4600 to acknowledge the request.
Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
Wait for the ADN4600 to acknowledge the request.
It is important to note that the SDA line only changes when
the SCL line is low, except when a start, stop, or repeated start
condition is being sent, as is the case in Step 1 and Step 9.
SCL
GENERAL CASE
SDA
START
FIXED PART ADDR
ADDR
[1:0] R/W ACK
REGISTER ADDR
ACK
DATA
ACK
STOP
EXAMPLE
SDA
1
2
2
3
4
5
2
Figure 31. I C Write Diagram
Rev. 0 | Page 22 of 22
6
7
8
9
07061-008
1.
In Figure 31, the ADN4600 write process is shown. The SCL
signal is shown, along with a general write operation and a
specific example. In the example, Data 0x92 is written to Register
Address 0x6D of an ADN4600 part with a slave address of 0x4B.
The slave address is seven bits wide. The upper five bits of the
slave address are internally set to b10010. The lower two bits
are controlled by the ADDR[1:0] pins. In this example, the bits
controlled by the ADDR[1:0] pins are set to b11. In the figure,
the corresponding step number is visible in the circle under the
waveform. The SCL line is driven by the I2C master, not by the
ADN4600 slave. As for the SDA line, the data in the shaded
polygons of Figure 31 is driven by the ADN4600, whereas the
data in the nonshaded polygons is driven by the I2C master. The
end phase case shown corresponds with Step 9.
ADN4600
I2C Interface Data Transfers: Data Read
14. Send a repeated start condition (that is, while holding the
SCL line high, pull the SDA line low) and continue with
Step 2 of the write procedure (see the I2C Interface Data
Transfers: Data Write section) to perform a write.
15. Send a repeated start condition (that is, while holding the
SCL line high, pull the SDA line low) and continue with
Step 2 of the read procedure to perform a read from a
another address.
16. Send a repeated start condition (that is, while holding the
SCL line high, pull the SDA line low) and continue with
Step 8 of the read procedure to perform a read from the
same address.
To read data from the ADN4600 register set, a microcontroller
(or any other I2C master) needs to send the appropriate control
signals to the ADN4600 slave device. Use the following steps,
where the signals are controlled by the I2C master unless otherwise
specified. A diagram of the procedure is shown in Figure 32.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Send a start condition (that is, while holding the SCL line
high, pull the SDA line low).
Send the ADN4600 part address (seven bits), whose upper
five bits are the static value b10010 and whose lower two
bits are controlled by the ADDR1 and ADDR0 input pins.
This transfer should be MSB first.
Send the write indicator bit (0).
Wait for the ADN4600 to acknowledge the request.
Send the register address (eight bits) from which data is to
be read. This transfer should be MSB first. The register
address is kept in the ADN4600 memory until the part is
reset or the register address is written over with the same
procedure (Step 1 to Step 6 of the write procedure; see the
I2C Interface Data Transfers: Data Write section).
Wait for the ADN4600 to acknowledge the request.
Send a repeated start condition (that is, while holding the
SCL line high, pull the SDA line low).
Send the ADN4600 part address (seven bits), whose upper
five bits are the static value b10010 and whose lower two
bits are controlled by the ADDR1 and ADDR0 input pins.
This transfer should be MSB first.
Send the read indicator bit (1).
Wait for the ADN4600 to acknowledge the request.
The ADN4600 then serially transfers the data (eight bits) held
in the register indicated by the address set in Step 5.
Acknowledge the data.
Send a stop condition (that is, while holding the SCL line
high, pull the SDA line high) and release control of the bus.
In Figure 32, the ADN4600 read process is shown. The SCL
signal is shown, along with a general read operation and a
specific example. In the example, Data 0x49 is read from Register
Address 0x6D of an ADN4600 part with a slave address of 0x4B.
The part address is seven bits wide. The upper five bits of the
slave address are internally set to b10010. The lower two bits
are controlled by the ADDR[1:0] pins. In this example, the bits
controlled by the ADDR[1:0] pins are set to b11. In Figure 32,
the corresponding step number is visible in the circle under the
waveform. The SCL line is driven by the I2C master, not by the
ADN4600 slave. As for the SDA line, the data in the shaded
polygons of Figure 32 is driven by the ADN4600, whereas the
data in the nonshaded polygons is driven by the I2C master. The
end phase case shown corresponds with Step 13.
It is important to note that the SDA line only changes when
the SCL line is low, except when a start, stop, or repeated start
condition is being sent, as is the case in Step 1, Step 7, and Step 13.
In Figure 32, Sr represents a repeated start where the SDA line
is brought high before SCL is raised. SDA is then dropped while
SCL is still high.
SCL
GENERAL CASE
SDA START
FIXED PART
ADDR
ADDR R/
[1:0] W
A
REGISTER ADDR
A Sr
FIXED PART
ADDR
ADDR R/
[1:0] W A
DATA
A
11
12
STOP
EXAMPLE
SDA
1
2
2
3
4
5
6
7
8
8
9
10
NOTES
1. A = ACK.
2. Sr = A REPEATED START WHERE THE SDA LINE IS BROUGHT HIGH BEFORE SCL IS RAISED.
Figure 32. I2C Read Diagram
Rev. 0 | Page 23 of 23
13
07061-009
1.
ADN4600
PCB DESIGN GUIDELINES
Transmission Lines
Proper RF PCB design techniques must be used for optimal
performance.
Use of 50 Ω transmission lines is required for all high frequency
input and output signals to minimize reflections. It is also necessary
for the high speed pairs of differential input traces, as well as the
high speed pairs of differential output traces, to be matched in
length to avoid skew between the differential traces.
Power Supply Connections and Ground Planes
Use of one low impedance ground plane is recommended. The
VEE pins should be soldered directly to the ground plane to
reduce series inductance. If the ground plane is an internal
plane and connections to the ground plane are made through
vias, multiple vias can be used in parallel to reduce the series
inductance. The exposed pad should be connected to the VEE
plane using plugged vias so that solder does not leak through
the vias during reflow.
Use of a 10 μF electrolytic capacitor between VCC and VEE is
recommended at the location where the 3.3 V supply enters the
PCB. It is recommended that 0.1 μF and 1 nF ceramic chip
capacitors be placed in parallel at each supply pin for high
frequency power supply decoupling. When using 0.1 μF and 1 nF
ceramic chip capacitors, they should be placed between the IC
power supply pins (VCC, VTTI, VTTO) and VEE, as close as
possible to the supply pins.
Soldering Guidelines for Chip Scale Package
The lands on the LFCSP are rectangular. The printed circuit
board pad for these should be 0.1 mm longer than the package
land length and 0.05 mm wider than the package land width.
The land should be centered on the pad. This ensures that the
solder joint size is maximized. The bottom of the chip scale
package has a central exposed pad. The pad on the printed
circuit board should be at least as large as this exposed pad. The
user must connect the exposed pad to VEE using plugged vias
so that solder does not leak through the vias during reflow. This
ensures a solid connection from the exposed pad to VEE.
By using adjacent power supply and GND planes, excellent high
frequency decoupling can be attained by using close spacing
between the planes. This capacitance is given by
CPLANE = 0.88εr A/d (pF)
where:
εr is the dielectric constant of the PCB material.
A is the area of the overlap of power and GND planes (cm2).
d is the separation between planes (mm).
For FR4, εr = 4.4 and 0.25 mm spacing, C ~15 pF/cm2.
Rev. 0 | Page 24 of 24
ADN4600
CONTROL REGISTER MAP
Table 16. Basic Mode I2C Register Definitions
Addr
(Hex)
0x00
0x40
0x41
0x50
0x51
0x52
0x53
0x54
0x55
0x56
0x57
0x58
0x59
0x5A
0x5B
0x80
0x88
0x90
0x98
0xA0
0xA8
0xB0
0xB8
0xC0
0xC8
0xD0
0xD8
0xE0
0xE8
0xF0
0xF8
Name
Reset
XPT
Configuration
XPT Update
XPT Status 0
XPT Status 1
XPT Status 2
XPT Status 3
XPT Status 4
XPT Status 5
XPT Status 6
XPT Status 7
XPT Temp 0
XPT Temp 1
XPT Temp 2
XPT Temp 3
RX0
Configuration
RX1
Configuration
RX2
Configuration
RX3
Configuration
RX4
Configuration
RX5
Configuration
RX6
Configuration
RX7
Configuration
TX0
Configuration
TX1
Configuration
TX2
Configuration
TX3
Configuration
TX7
Configuration
TX6
Configuration
TX5
Configuration
TX4
Configuration
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
IN PORT[2]
IN PORT[1]
IN PORT[0]
Broadcast
OUT PORT[2]
OUT PORT[1]
Bit 0
Reset
OUT PORT[0]
OUT0[1]
OUT1[1]
OUT2[1]
OUT3[1]
OUT4[1]
OUT5[1]
OUT6[1]
OUT7[1]
OUT0[1]
OUT2[1]
OUT4[1]
OUT6[1]
RX EQ[1]
Update
OUT0[0]
OUT1[0]
OUT2[0]
OUT3[0]
OUT4[0]
OUT5[0]
OUT6[0]
OUT7[0]
OUT0[0]
OUT2[0]
OUT4[0]
OUT6[0]
RX EQ[0]
0x30
OUT1[2]
OUT3[2]
OUT5[2]
OUT7[2]
RX
PNSWAP
RX
PNSWAP
RX
PNSWAP
RX
PNSWAP
RX
PNSWAP
RX
PNSWAP
RX
PNSWAP
RX
PNSWAP
Default
0x00
0x00
OUT1[1]
OUT3[1]
OUT5[1]
OUT7[1]
RX EQBY
OUT1[0]
OUT3[0]
OUT5[0]
OUT7[0]
RX EN
OUT0[2]
OUT1[2]
OUT2[2]
OUT3[2]
OUT4[2]
OUT5[2]
OUT6[2]
OUT7[2]
OUT0[2]
OUT2[2]
OUT4[2]
OUT6[2]
RX EQ[2]
RX EQBY
RX EN
RX EQ[2]
RX EQ[1]
RX EQ[0]
0x30
RX EQBY
RX EN
RX EQ[2]
RX EQ[1]
RX EQ[0]
0x30
RX EQBY
RX EN
RX EQ[2]
RX EQ[1]
RX EQ[0]
0x30
RX EQBY
RX EN
RX EQ[2]
RX EQ[1]
RX EQ[0]
0x30
RX EQBY
RX EN
RX EQ[2]
RX EQ[1]
RX EQ[0]
0x30
RX EQBY
RX EN
RX EQ[2]
RX EQ[1]
RX EQ[0]
0x30
RX EQBY
RX EN
RX EQ[2]
RX EQ[1]
RX EQ[0]
0x30
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
TX EN
TX data rate
TX PE[2]
TX PE[1]
TX PE[0]
0x20
Rev. 0 | Page 25 of 25
ADN4600
Table 17. Advanced Mode I2C Register Definitions
Addr
(Hex)
0x23
0x83
0x84
0x85
0x8B
0x8C
0x8D
0x93
0x94
0x95
0x9B
0x9C
0x9D
0xA3
0xA4
0xA5
0xAB
0xAC
0xAD
0xB3
0xB4
0xB5
0xBB
0xBC
0xBD
0xC1
0xC2
0xC3
0xC9
0xCA
0xCB
Name
TxHeadroom
RX0 EQ1
Control
RX0 EQ3
Control
RX0 FR4
Control
RX1 EQ1
Control
RX1 EQ3
Control
RX1 FR4
Control
RX2 EQ1
Control
RX2 EQ3
Control
RX2 FR4
Control
RX3 EQ1
Control
RX3 EQ3
Control
RX3 FR4
Control
RX4 EQ1
Control
RX4 EQ3
Control
RX4 FR4
Control
RX5 EQ1
Control
RX5 EQ3
Control
RX5 FR4
Control
RX6 EQ1
Control
RX6 EQ3
Control
RX6 FR4
Control
RX7 EQ1
Control
RX7 EQ3
Control
RX7 FR4
Control
TX0 Output
Level Control 1
TX0 Output
Level Control 0
TX0 Squelch
Control
TX1 Output
Level Control 1
TX1 Output
Level Control 0
TX1 Squelch
Control
Bit 7
TxH_B3
Bit 6
TxH_B2
EQ CTL SRC
EQ CTL SRC
EQ CTL SRC
EQ CTL SRC
EQ CTL SRC
EQ CTL SRC
EQ CTL SRC
EQ CTL SRC
Bit 5
TxH_B1
RX EQ1[5]
Bit 4
TxH_B0
RX EQ1[4]
Bit 3
TxH_A3
RX EQ1[3]
Bit 2
TxH_A2
RX EQ1[2]
Bit 1
TxH_A1
RX EQ1[1]
Bit 0
TxH_A0
RX EQ1[0]
Default
0x00
0x00
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
FR4/CX4
RX EQ1[0]
0x00
0x00
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX LUT
select
RX EQ1[1]
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
FR4/CX4
RX EQ1[0]
0x00
0x00
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX LUT
select
RX EQ1[1]
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
FR4/CX4
RX EQ1[0]
0x00
0x00
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX LUT
select
RX EQ1[1]
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
FR4/CX4
RX EQ1[0]
0x00
0x00
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX LUT
select
RX EQ1[1]
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
FR4/CX4
RX EQ1[0]
0x00
0x00
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX LUT
select
RX EQ1[1]
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
FR4/CX4
RX EQ1[0]
0x00
0x00
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX LUT
select
RX EQ1[1]
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
FR4/CX4
RX EQ1[0]
0x00
0x00
RX EQ1[5]
RX EQ1[4]
RX EQ1[3]
RX EQ1[2]
RX LUT
select
RX EQ1[1]
RX EQ3[5]
RX EQ3[4]
RX EQ3[3]
RX EQ3[2]
RX EQ3[1]
RX EQ3[0]
0x00
RX LUT
select
RX LUT
FR4/CX4
0x00
TX0 CTL
SRC
TX0_OLEV1[6:0]
0x40
TX0_OLEV0[6:0]
0x40
SQUELCHb[3:0]
TX1 CTL
SRC
DISABLEb[3:0]
0xFF
TX1_OLEV1[6:0]
0x40
TX1_OLEV0[6:0]
0x40
SQUELCHb[3:0]
DISABLEb[3:0]
Rev. 0 | Page 26 of 26
0xFF
ADN4600
Addr
(Hex)
0xD1
0xD2
0xD3
0xD9
0xDA
0xDB
0xE1
0xE2
0xE3
0xE9
0xEA
0xEB
0xF1
0xF2
0xF3
0xF9
0xFA
0xFB
Name
TX2 Output
Level Control 1
TX2 Output
Level Control 0
TX2 Squelch
Control
TX3 Output
Level Control 1
TX3 Output
Level Control 0
TX3 Squelch
Control
TX7 Output
Level Control 1
TX7 Output
Level Control 0
TX7 Squelch
Control
TX6 Output
Level Control 1
TX6 Output
Level Control 0
TX6 Squelch
Control
TX5 Output
Level Control 1
TX5 Output
Level Control 0
TX5 Squelch
Control
TX4 Output
Level Control 1
TX4 Output
Level Control 0
TX4 Squelch
Control
Bit 7
TX2 CTL
SRC
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
TX2_OLEV1[6:0]
Bit 1
TX2_OLEV0[6:0]
SQUELCHb[3:0]
TX3 CTL
SRC
0x40
TX3_OLEV0[6:0]
0x40
DISABLEb[3:0]
0x40
TX7_OLEV0[6:0]
0x40
DISABLEb[3:0]
0xFF
TX6_OLEV1[6:0]
0x40
TX6_OLEV0[6:0]
0x40
DISABLEb[3:0]
0xFF
TX5_OLEV1[6:0]
0x40
TX5_OLEV0[6:0]
0x40
SQUELCHb[3:0]
TX4 CTL
SRC
0xFF
TX7_OLEV1[6:0]
SQUELCHb[3:0]
TX5 CTL
SRC
0xFF
TX3_OLEV1[6:0]
SQUELCHb[3:0]
TX6 CTL
SRC
Default
0x40
0x40
DISABLEb[3:0]
SQUELCHb[3:0]
TX7 CTL
SRC
Bit 0
DISABLEb[3:0]
0xFF
TX4_OLEV1[6:0]
0x40
TX4_OLEV0[6:0]
0x40
SQUELCHb[3:0]
DISABLEb[3:0]
Rev. 0 | Page 27 of 27
0xFF
ADN4600
PACKAGE OUTLINE DIMENSIONS
9.00
BSC SQ
0.60 MAX
8.75
BSC SQ
TOP
VIEW
(BOTTOM VIEW)
17 16
7.50
REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.50 BSC
0.20 REF
*COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4
EXCEPT FOR EXPOSED PAD DIMENSION
063006-B
SEATING
PLANE
33
32
PIN 1
INDICATOR
*6.15
6.00 SQ
5.85
EXPOSED PAD
0.50
0.40
0.30
12° MAX
64 1
49
48
PIN 1
INDICATOR
1.00
0.85
0.80
0.30
0.25
0.18
0.60 MAX
Figure 33. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
9 mm × 9 mm Body, Very Thin Quad
(CP-64-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADN4600ACPZ 1
AD4600ACPZ-R71
ADN4600-EVALZ1
1
Temperature Range
−40°C to +85°C
−40oC to +85oC
Package Description
64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
Z = RoHS Compliant Part.
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07061-0-6/08(0)
Rev. 0 | Page 28 of 28
Package Option
CP-64-2
CP-64-2