Electrical Specifications Subject to Change LTC2230/LTC2231 10-Bit,170Msps/ 135Msps ADCs U FEATURES DESCRIPTIO ■ The LTC®2230 and LTC2231 are 170Msps/135Msps, sampling 10-bit A/D converters designed for digitizing high frequency, wide dynamic range signals. The LTC2230/ LTC2231 are perfect for demanding communications applications with AC performance that includes 61dB SNR and 75dB spurious free dynamic range for signals up to 200MHz. Ultralow jitter of 0.15psRMS allows undersampling of IF frequencies with excellent noise performance. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Sample Rate: 170Msps/135 Msps 61dB SNR up to 140MHz Input 75dB SFDR up to 200MHz Input 775MHz Full Power Bandwidth S/H Single 3.3V Supply Low Power Dissipation: 890mW/660mW LVDS, CMOS, or Demultiplexed CMOS Outputs Selectable Input Ranges: ±0.5V or ±1V No Missing Codes Optional Clock Duty Cycle Stabilizer Shutdown and Nap Modes Data Ready Output Clock Pin Compatible Family 170Msps: LTC2220 (12-Bit), LTC2230 (10-Bit) 135Msps: LTC2221 (12-Bit), LTC2231 (10-Bit) 64-Pin 9mm x 9mmQFN Package DC specs include ±0.2LSB INL (typ), ±0.1LSB DNL (typ) and no missing codes over temperature. The transition noise is a low 0.12LSBRMS. The digital outputs can be either differential LVDS, or single-ended CMOS. There are three format options for the CMOS outputs: a single bus running at the full data rate or two demultiplexed buses running at half data rate with either interleaved or simultaneous update. A separate output power supply allows the CMOS output swing to range from 0.5V to 3.3V. U APPLICATIO S ■ ■ ■ ■ Wireless and Wired Broadband Communication Cable Head-End Systems Power Amplifier Linearization Communications Test Equipment The ENC+ and ENC – inputs may be driven differentially or single ended with a sine wave, PECL, LVDS, TTL, or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles. , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATIO 3.3V VDD REFH REFL SFDR vs Input Frequency 90 0.5V TO 3.3V FLEXIBLE REFERENCE 85 4th OR HIGHER 80 OVDD ANALOG INPUT INPUT S/H – 10-BIT PIPELINED ADC CORE CORRECTION LOGIC D9 • • • D0 OUTPUT DRIVERS 75 CMOS OR LVDS SFDR (dBFS) + 70 2nd OR 3rd 65 60 55 OGND 50 45 CLOCK/DUTY CYCLE CONTROL 40 0 100 300 500 200 400 INPUT FREQUENCY (MHz) 600 22301 TA01 2230 TA01b ENCODE INPUT 22301p 1 LTC2230/LTC2231 U W W W ABSOLUTE AXI U RATI GS U W U PACKAGE/ORDER I FOR ATIO OVDD = VDD (Notes 1, 2) TOP VIEW 64 GND 63 VDD 62 VDD 61 GND 60 VCM 59 SENSE 58 MODE 57 LVDS 56 OF +/OFA 55 OF –/DA9 54 D9+/DA8 53 D9–/DA7 52 D8+/DA6 51 D8–/DA5 50 OGND 49 OVDD Supply Voltage (VDD) ................................................. 4V Digital Output Ground Voltage (OGND) ....... –0.3V to 1V Analog Input Voltage (Note 3) ..... –0.3V to (VDD + 0.3V) Digital Input Voltage .................... –0.3V to (VDD + 0.3V) Digital Output Voltage ............... –0.3V to (OVDD + 0.3V) Power Dissipation ............................................ 1500mW Operating Temperature Range LTC2230C, LTC2231C ............................. 0°C to 70°C LTC2230I, LTC2231I ...........................–40°C to 85°C Storage Temperature Range ..................–65°C to 125°C AIN+ 1 AIN+ 2 AIN– 3 AIN– 4 REFHA 5 REFHA 6 REFLB 7 REFLB 8 REFHB 9 REFHB 10 REFLA 11 REFLA 12 VDD 13 VDD 14 VDD 15 GND 16 48 D7+/DA4 47 D7–/DA3 46 D6+/DA2 45 D6–/DA1 44 D5+/DA0 43 D5–/DNC 42 OVDD 41 OGND 40 D4+/DNC 39 D4–/CLOCKOUTA 38 D3+/CLOCKOUTB 37 D3–/OFB 36 CLOCKOUT +/DB9 35 CLOCKOUT –/DB8 34 OVDD 33 OGND ENC + 17 ENC – 18 SHDN 19 OE 20 DNC 21 DNC 22 DNC/DB0 23 DNC/DB1 24 OGND 25 OVDD 26 D0–/DB2 27 D0+/DB3 28 D1–/DB4 29 D1+/DB5 30 D2–/DB6 31 D2+/DB7 32 65 UP PACKAGE 64-LEAD (9mm × 9mm) PLASTIC QFN EXPOSED PAD IS GND (PIN 65), MUST BE SOLDERED TO PCB TJMAX = 125°C, θJA = 20°C/W ORDER PART NUMBER LTC2230CUP LTC2230IUP LTC2231CUP LTC2231IUP UP PART MARKING 2230 2230 2231 2231 Consult LTC Marketing for parts specified with wider operating temperature ranges. U CO VERTER CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4) PARAMETER CONDITIONS Resolution (No Missing Codes) MIN ● 10 TYP MAX UNITS Bits Integral Linearity Error Differential Analog Input ● –0.8 ±0.2 0.8 LSB Differential Linearity Error Differential Analog Input ● –0.6 ±0.1 0.6 LSB Integral Linearity Error Single-Ended Analog Input ±0.5 LSB Differential Linearity Error Single-Ended Analog Input ±0.1 LSB Offset Error Gain Error External Reference Offset Drift ● –20 ±3 20 mV ● –3 ±0.5 3 %FS ±10 µV/C Full-Scale Drift Internal Reference External Reference ±30 ±15 ppm/C ppm/C Transition Noise SENSE = 1V 0.12 LSBRMS 22301p 2 LTC2230/LTC2231 U U A ALOG I PUT The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 9) SYMBOL PARAMETER CONDITIONS VIN Analog Input Range (AIN+ – AIN–) 3.1V < VDD < 3.5V ● VIN, CM Analog Input Common Mode Differential Input ● 1 IIN Analog Input Leakage Current 0 < AIN+, AIN– ● ISENSE SENSE Input Leakage 0V < SENSE < 1V ● IMODE MODE Pin Pull-Down Current to GND 10 µA ILVDS LVDS Pin Pull-Down Current to GND 10 µA tAP Sample and Hold Acquisition Delay Time 0 ns tJITTER Sample and Hold Acquisition Delay Time Jitter CMRR W U DY A IC ACCURACY SNR Signal-to-Noise Ratio (Note 10) 5MHz Input (1V Range) 5MHz Input (2V Range) 70MHz Input (1V Range) 70MHz Input (2V Range) V –1 1 µA –1 1 µA Spurious Free Dynamic Range 2nd or 3rd Harmonic (Note 11) Spurious Free Dynamic Range 4th Harmonic or Higher (Note 11) 80 dB 775 MHz MIN LTC2230 TYP MAX MIN 59.5 61.2 60 59.5 61.1 60 LTC2231 TYP MAX UNITS 59.5 61.2 dB dB 59.5 61.1 dB dB 59.4 61.0 59.4 61.0 dB dB 250MHz Input (1V Range) 250MHz Input (2V Range) 59.0 60.6 59.0 60.6 dB dB 80 78 80 78 dB dB 80 78 dB dB 5MHz Input (1V Range) 5MHz Input (2V Range) 70 80 78 70 140MHz Input (1V Range) 140MHz Input (2V Range) 78 78 78 78 dB db 250MHz Input (1V Range) 250MHz Input (2V Range) 75 74 78 78 dB dB 5MHz Input (1V Range) 5MHz Input (2V Range) 86 86 86 86 dB dB 86 86 dB dB 70MHz Input (1V Range) 70MHz Input (2V Range) 75 86 86 75 140MHz Input (1V Range) 140MHz Input (2V Range) 86 86 86 86 dB dB 250MHz Input (1V Range) 250MHz Input (2V Range) 85 85 85 85 dB dB 59.5 61.2 59.5 61.2 dB dB 59.5 61.1 dB dB 81 dBc 5MHz Input (1V Range) 5MHz Input (2V Range) 70MHz Input (1V Range) 70MHz Input (2V Range) Intermodulation Distortion psRMS 140MHz Input (1V Range) 140MHz Input (2V Range) 70MHz Input (1V Range) 70MHz Input (2V Range) IMD V TA = 25°C. AIN = –1dBFS. (Note 4) CONDITIONS Signal-to-Noise Plus Distortion Ratio (Note 12) 1.6 UNITS 1.9 Figure 8 Test Circuit PARAMETER S/(N+D) MAX 0.15 SYMBOL SFDR < VDD TYP ±0.5 to ±1 Analog Input Common Mode Rejection Ratio Full Power Bandwidth SFDR MIN fIN1 = 138MHz, fIN2 = 140MHz 60 59.5 61.1 81 60 22301p 3 LTC2230/LTC2231 U U U I TER AL REFERE CE CHARACTERISTICS (Note 4) PARAMETER CONDITIONS MIN TYP MAX VCM Output Voltage IOUT = 0 1.575 1.600 1.625 VCM Output Tempco UNITS V ±25 ppm/C VCM Line Regulation 3.1V < VDD < 3.5V 3 mV/V VCM Output Resistance –1mA < IOUT < 1mA 4 Ω U U DIGITAL I PUTS A D DIGITAL OUTPUTS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 2.5 V V ENCODE INPUTS (ENC +, ENC –) VID Differential Input Voltage VICM Common Mode Input Voltage RIN Input Resistance CIN Input Capacitance ● Internally Set Externally Set (Note 7) ● 0.2 1.1 (Note 7) V 1.6 1.6 6 kΩ 3 pF LOGIC INPUTS (OE, SHDN) VIH High Level Input Voltage VDD = 3.3V ● VIL Low Level Input Voltage VDD = 3.3V ● IIN Input Current VIN = 0V to VDD ● CIN Input Capacitance (Note 7) 2 V –10 0.8 V 10 µA 3 pF LOGIC OUTPUTS (CMOS MODE) OVDD = 3.3V COZ Hi-Z Output Capacitance OE = High (Note 7) 3 pF ISOURCE Output Source Current VOUT = 0V 50 mA ISINK Output Sink Current VOUT = 3.3V 50 mA VOH High Level Output Voltage IO = –10µA IO = –200µA ● IO = 10µA IO = 1.6mA ● VOL Low Level Output Voltage 3.1 3.295 3.29 0.005 0.09 V V 0.4 V V OVDD = 2.5V VOH High Level Output Voltage IO = –200µA 2.49 V VOL Low Level Output Voltage IO = 1.6mA 0.09 V VOH High Level Output Voltage IO = –200µA 1.79 V VOL Low Level Output Voltage IO = 1.6mA 0.09 V OVDD = 1.8V LOGIC OUTPUTS (LVDS MODE) VOD Differential Output Voltage 100Ω Differential Load ● 247 350 454 VOS Output Common Mode Voltage 100Ω Differential Load ● 1.125 1.250 1.375 mV V 22301p 4 LTC2230/LTC2231 U W POWER REQUIRE E TS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 9) CONDITIONS MIN LTC2230 TYP MAX PARAMETER VDD Analog Supply Voltage PSHDN Shutdown Power SHDN = H, OE = H, No CLK 2 2 mW PNAP Nap Mode Power SHDN = H, OE = L, No CLK 35 35 mW ● 3.1 3.3 3.5 MIN LTC2231 TYP MAX SYMBOL 3.1 3.3 UNITS 3.5 V LVDS OUTPUT MODE OVDD Output Supply Voltage ● IVDD Analog Supply Current ● IOVDD Output Supply Current ● 55 61 55 61 mA PDISS Power Dissipation ● 1050 1160 828 915 mW 3 3.3 3.6 264 290 3 3.3 3.6 V 196 216 mA CMOS OUTPUT MODE OVDD Output Supply Voltage ● IVDD Analog Supply Current ● PDISS Power Dissipation 0.5 3.3 3.6 264 290 0.5 890 3.3 3.6 V 196 216 mA 660 mW WU TI I G CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4) SYMBOL PARAMETER fS Sampling Frequency tL ENC Low Time tH ENC High Time tAP Sample-and-Hold Aperture Delay tOE Output Enable Delay CONDITIONS MIN ● 1 Duty Cycle Stabilizer Off Duty Cycle Stabilizer On ● ● 2.8 2 Duty Cycle Stabilizer Off Duty Cycle Stabilizer On ● ● 2.8 2 (Note 7) ● LTC2230 TYP MAX MIN LTC2231 TYP MAX UNITS 135 MHz 170 1 2.94 2.94 500 500 3.5 2 3.7 3.7 500 500 ns ns 2.94 2.94 500 500 3.5 2 3.7 3.7 500 500 ns ns 0 0 5 10 ns 5 10 ns LVDS OUTPUT MODE tD ENC to DATA Delay (Note 7) ● 1.3 2.2 3.5 1.3 2.2 3.5 ns tC ENC to CLOCKOUT Delay (Note 7) ● 1.3 2.2 3.5 1.3 2.2 3.5 ns DATA to CLOCKOUT Skew (tC - tD) (Note 7) ● –0.6 0 0.6 –0.6 0 0.6 ns Rise Time 0.5 0.5 ns Fall Time 0.5 0.5 ns 5 5 Pipeline Latency Cycles CMOS OUTPUT MODE tD ENC to DATA Delay (Note 7) ● 1.3 2.1 3.5 1.3 2.1 3.5 ns tC ENC to CLOCKOUT Delay (Note 7) ● 1.3 2.1 3.5 1.3 2.1 3.5 ns DATA to CLOCKOUT Skew (tC - tD) (Note 7) ● –0.6 0 0.6 –0.6 0 0.6 Pipeline Latency Full Rate CMOS Demuxed Interleaved Demuxed Simultaneous ns 5 5 Cycles 5 5 Cycles 5 and 6 5 and 6 Cycles 22301p 5 LTC2230/LTC2231 ELECTRICAL CHARACTERISTICS Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: All voltage values are with respect to ground with GND and OGND wired together (unless otherwise noted). Note 3: When these pin voltages are taken below GND or above VDD, they will be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND or above VDD without latchup. Note 4: VDD = 3.3V, fSAMPLE = 170MHz (LTC2230) or 135MHz (LTC2231), LVDS outputs differential, ENC+/ENC– = 2VP-P sine wave, input range = 2VP-P with differential drive, unless otherwise noted. Note 5: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 6: Offset error is the offset voltage measured from –0.5 LSB when the output code flickers between 00 0000 0000 and 11 1111 1111 in 2’s complement output mode. Note 7: Guaranteed by design, not subject to test. Note 8: Recommended operating conditions. Note 9: VDD = 3.3V, fSAMPLE = 170MHz (LTC2230) or 135MHz (LTC2231), differential ENC+/ENC– = 2VP-P sine wave, input range = 1VP-P with differential drive, output CLOAD = 5pF. Note 10: SNR minimum and typical values are for LVDS mode. Typical values for CMOS mode are typically 0.7dB to 0.9dB lower. Note 11: SFDR minimum values are for LVDS mode. Typical values are for both LVDS and CMOS modes. Note 12: SINAD minimum and typical values are for LVDS mode. Typical values for CMOS mode are typically 0.5dB to 0.9dB lower. U W TYPICAL PERFOR A CE CHARACTERISTICS LTC2230: DNL, 2V Range 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0 – 0.2 100000 0 – 0.2 – 0.4 – 0.6 – 0.6 – 0.8 – 0.8 80000 60000 40000 20000 – 1.0 256 0 512 OUTPUT CODE 768 512 OUTPUT CODE 768 2230 G01 7 6 0 256 0 1024 131059 120000 0.2 – 0.4 – 1.0 LTC2230: Noise Histogram 140000 COUNT ERROR (LSB) ERROR (LSB) LTC2230: INL, 2V Range 1.0 1024 513 514 515 CODE 2230 G02 LTC2230: SNR vs Input Frequency, –1dB, 2V Range 2230 G23 LTC2230: SNR vs Input Frequency, –1dB, 1V Range 63 63 62 62 61 61 LTC2230: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 2V Range 90 60 80 75 SFDR (dBFS) SNR (dBFS) SNR (dBFS) 85 60 59 59 58 58 57 57 70 65 60 55 50 45 0 100 300 400 500 200 INPUT FREQUENCY (MHz) 600 2230 G03 0 100 300 400 500 200 INPUT FREQUENCY (MHz) 600 2230 G04 40 0 100 300 500 200 400 INPUT FREQUENCY (MHz) 600 2230 G05 22301p 6 LTC2230/LTC2231 U W TYPICAL PERFOR A CE CHARACTERISTICS LTC2230: SFDR (HD4+) vs Input Frequency, –1dB, 2V Range 90 85 85 80 80 80 75 75 75 70 65 60 SFDR (dBFS) 90 85 70 65 60 70 65 60 55 55 55 50 50 50 45 45 45 40 40 100 300 500 200 400 600 INPUT FREQUENCY (MHz) 2230 G06 85 SFDR AND SNR (dBFS) SFDR 75 70 65 SNR 60 55 100 40 300 500 200 400 600 INPUT FREQUENCY (MHz) 2230 G07 LTC2230: SFDR and SNR vs Sample Rate, 1V Range, fIN = 30MHz, –1dB 90 80 0 90 290 85 280 SFDR 80 70 65 SNR 2V RANGE 250 1V RANGE 240 210 0 20 40 60 80 100 120 140 160 180 200 SAMPLE RATE (Msps) 2230 G10 0 20 40 60 80 100 120 140 160 180 200 SAMPLE RATE (Msps) 2230 G11 LTC2230: SFDR vs Input Level, f IN = 70MHz, 2V Range LTC2230: IOVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB 60 100 90 LVDS OUTPUTS, 0VDD = 3.3V 50 dBFS SFDR (dBc AND dBFS) 80 40 IOVDD (mA) 260 220 50 0 20 40 60 80 100 120 140 160 180 200 SAMPLE RATE (Msps) 2230 G09 300 500 200 400 600 INPUT FREQUENCY (MHz) 2230 G08 230 55 50 100 270 75 60 0 LTC2230: IVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB IVDD (mA) 0 LTC2230: SFDR and SNR vs Sample Rate, 2V Range, fIN = 30MHz, –1dB SFDR AND SNR (dBFS) LTC2230: SFDR (HD4+) vs Input Frequency, –1dB, 1V Range 90 SFDR (dBFS) SFDR (dBFS) LTC2230: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 1V Range 30 20 CMOS OUTPUTS, 0VDD = 1.8V 10 70 60 dBc 50 40 30 20 10 0 0 20 40 60 80 100 120 140 160 180 200 SAMPLE RATE (Msps) 2230 G12 0 –50 –40 –30 –10 –20 INPUT LEVEL (dBFS) 0 2230 G13 22301p 7 LTC2230/LTC2231 U W TYPICAL PERFOR A CE CHARACTERISTICS LTC2230: 8192 Point FFT, f IN = 30MHz, –1dB, 1V Range LTC2230: 8192 Point FFT, f IN = 70MHz, –1dB, 2V Range 0 0 –10 –10 –20 –20 –20 –30 –30 –30 –40 –40 –40 –50 –60 –70 –80 AMPLITUDE (dB) 0 –10 AMPLITUDE (dB) AMPLITUDE (dB) LTC2230: 8192 Point FFT, f IN = 30MHz, –1dB, 2V Range –50 –60 –70 –80 –50 –60 –70 –80 –90 –90 –90 –100 –100 –100 –110 –110 –110 –120 –120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 10 20 2230 G14 LTC2230: 8192 Point FFT, f IN = 70MHz, –1dB, 1V Range 30 40 50 60 FREQUENCY (MHz) 70 80 –120 0 0 –10 –10 –20 –20 –20 –30 –30 –30 –40 –40 –40 –70 –80 AMPLITUDE (dB) 0 –60 –50 –60 –70 –80 –90 –100 –110 –110 –110 –120 –120 70 80 10 20 2230 G17 LTC2230: 8192 Point FFT, f IN = 250MHz, –1dB, 2V Range 30 40 50 60 FREQUENCY (MHz) 70 80 –120 0 0 –10 –10 –20 –20 –20 –30 –30 –30 –40 –40 –40 –70 –80 AMPLITUDE (dB) 0 –60 –50 –60 –70 –80 –90 –100 –110 –110 –110 –120 –120 70 80 2230 G20 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 2230 G19 –80 –100 30 40 50 60 FREQUENCY (MHz) 70 –70 –100 20 30 40 50 60 FREQUENCY (MHz) –60 –90 10 20 –50 –90 0 10 LTC2230: 8192 Point FFT, f IN = 500MHz, –6dB, 1V Range –10 –50 0 2230 G18 LTC2230: 8192 Point FFT, f IN = 250MHz, –1dB, 1V Range AMPLITUDE (dB) AMPLITUDE (dB) 0 80 2230 G16 –80 –100 30 40 50 60 FREQUENCY (MHz) 70 –70 –100 20 30 40 50 60 FREQUENCY (MHz) –60 –90 10 20 –50 –90 0 10 LTC2230: 8192 Point FFT, f IN = 140MHz, –1dB, 1V Range –10 –50 0 2230 G15 LTC2230: 8192 Point FFT, f IN = 140MHz, –1dB, 2V Range AMPLITUDE (dB) AMPLITUDE (dB) 0 80 2230 G21 –120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 2230 G22 22301p 8 LTC2230/LTC2231 U W TYPICAL PERFOR A CE CHARACTERISTICS LTC2231: DNL, 2V Range 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0 – 0.2 140000 100000 0 –0.2 –0.4 – 0.6 –0.6 – 0.8 –0.8 512 OUTPUT CODE 768 20000 512 OUTPUT CODE 768 513 1024 2231 G23 LTC2231: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 2V Range 90 64 85 63 63 62 62 61 60 59 58 58 57 57 56 56 55 0 100 500 200 300 400 INPUT FREQUENCY (MHz) 55 600 80 SFDR (dBFS) SNR (dBFS) 65 64 59 75 70 65 60 55 0 100 500 200 300 400 INPUT FREQUENCY (MHz) 2231 G03 50 600 LTC2231: SFDR (HD4+) vs Input Frequency, –1dB, 2V Range 85 85 80 80 80 75 75 75 SFDR (dBFS) 85 SFDR (dBFS) 90 70 65 65 60 60 55 55 55 100 200 300 400 500 INPUT FREQUENCY (MHz) 600 2231 G06 50 0 100 200 300 400 500 INPUT FREQUENCY (MHz) 600 70 60 0 200 300 400 500 INPUT FREQUENCY (MHz) LTC2231: SFDR (HD4+) vs Input Frequency, –1dB, 1V Range 90 50 100 2231 G05 90 65 0 2231 G04 LTC2231: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 1V Range 70 515 CODE 65 60 514 2231 G02 LTC2231: SNR vs Input Frequency, –1dB, 1V Range 61 3 5 0 256 0 1024 LTC2231: SNR vs Input Frequency, –1dB, 2V Range SNR (dBFS) 60000 40000 2231 G01 SFDR (dBFS) 80000 –1.0 256 0 131064 120000 0.2 – 0.4 – 1.0 LTC2231: Noise Histogram COUNT ERROR (LSB) ERROR (LSB) LTC2231: INL, 2V Range 600 2231 G07 50 0 100 200 300 400 500 INPUT FREQUENCY (MHz) 600 2231 G08 22301p 9 LTC2230/LTC2231 U W TYPICAL PERFOR A CE CHARACTERISTICS LTC2231: SFDR and SNR vs Sample Rate, 2V Range, fIN = 30MHz, –1dB LTC2231: SFDR and SNR vs Sample Rate, 1V Range, fIN = 30MHz, –1dB 85 85 SFDR 220 SFDR 80 75 70 65 SNR 60 55 210 75 200 IVDD (mA) SFDR AND SNR (dBFS) 80 SFDR AND SNR (dBFS) LTC2231: IVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB 70 65 SNR 60 160 50 0 20 40 60 80 100 120 140 160 SAMPLE RATE (Msps) 150 0 20 40 60 80 100 120 140 160 SAMPLE RATE (Msps) 2231 G09 0 20 40 60 80 100 120 140 160 180 SAMPLE RATE (Msps) 2231 G10 2231 G11 LTC2231: SFDR vs Input Level, f IN = 70MHz, 2V Range LTC2231: IOVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB 100 60 90 LVDS OUTPUTS, OVDD = 3.3V 50 dBFS SFDR (dBc AND dBFS) 80 40 IOVDD (mA) 1V RANGE 180 170 55 50 2V RANGE 190 30 20 CMOS OUTPUTS, OVDD = 1.8V 10 70 60 dBc 50 40 30 20 10 0 0 20 40 60 80 100 120 140 160 180 SAMPLE RATE (Msps) 2231 G12 0 –50 –40 –30 –10 –20 INPUT LEVEL (dBFS) 0 2231 G13 22301p 10 LTC2230/LTC2231 U W TYPICAL PERFOR A CE CHARACTERISTICS LTC2231: 8192 Point FFT, f IN = 30MHz, –1dB, 1V Range 0 0 –10 –10 –20 –20 –20 –30 –30 –30 –40 –40 –40 –50 –60 –70 –80 –50 –60 –70 –80 –50 –60 –70 –80 –90 –90 –90 –100 –100 –100 –110 –110 –110 –120 –120 –120 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 10 15 20 25 30 35 40 45 50 55 60 65 FREQUENCY (MHz) FREQUENCY (MHz) FREQUENCY (MHz) 2231 G14 2231 G15 LTC2231: 8192 Point FFT, f IN = 140MHz, –1dB, 2V Range 0 0 –10 –10 –20 –20 –20 –30 –30 –30 –40 –40 –40 –60 –70 –80 AMPLITUDE (dB) 0 –50 2231 G16 LTC2231: 8192 Point FFT, f IN = 140MHz, –1dB, 1V Range –10 AMPLITUDE (dB) –50 –60 –70 –80 –50 –60 –70 –80 –90 –90 –90 –100 –100 –100 –110 –110 –110 –120 –120 –120 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 10 15 20 25 30 35 40 45 50 55 60 65 FREQUENCY (MHz) FREQUENCY (MHz) FREQUENCY (MHz) 2231 G17 LTC2231: 8192 Point FFT, f IN = 250MHz, –1dB, 2V Range 2231 G18 LTC2231: 8192 Point FFT, f IN = 250MHz, –1dB, 1V Range 0 0 –10 –10 –20 –20 –20 –30 –30 –30 –40 –40 –40 AMPLITUDE (dB) 0 –10 –50 –60 –70 –80 2231 G19 LTC2231: 8192 Point FFT, f IN = 500MHz, –6dB, 1V Range AMPLITUDE (dB) AMPLITUDE (dB) AMPLITUDE (dB) 0 LTC2231: 8192 Point FFT, f IN = 70MHz, –1dB, 1V Range AMPLITUDE (dB) LTC2231: 8192 Point FFT, f IN = 70MHz, –1dB, 2V Range –10 AMPLITUDE (dB) AMPLITUDE (dB) LTC2231: 8192 Point FFT, f IN = 30MHz, –1dB, 2V Range –50 –60 –70 –80 –50 –60 –70 –80 –90 –90 –90 –100 –100 –100 –110 –110 –110 –120 –120 –120 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 10 15 20 25 30 35 40 45 50 55 60 65 FREQUENCY (MHz) FREQUENCY (MHz) FREQUENCY (MHz) 2231 G20 2231 G21 2231 G22 22301p 11 LTC2230/LTC2231 U U U PI FU CTIO S (CMOS Mode) AIN+ (Pins 1, 2): Positive Differential Analog Input. AIN – (Pins 3, 4): Negative Differential Analog Input. DB0 - DB9 (Pins 23, 24, 27, 28, 29, 30, 31, 32, 35, 36): Digital Outputs, B bus. At high impedance in full rate CMOS mode. DB9 is MSB. OGND (Pins 25, 33, 41, 50): Output Driver Ground. REFHA (Pins 5, 6): ADC High Reference. Bypass to Pins 7, 8 with 0.1µF ceramic chip capacitor, to Pins 11, 12 with a 2.2µF ceramic capacitor and to ground with 1µF ceramic capacitor. OVDD (Pins 26, 34, 42, 49): Positive Supply for the Output Drivers. Bypass to ground with 0.1µF ceramic chip capacitor. REFLB (Pins 7, 8): ADC Low Reference. Bypass to Pins 5, 6 with 0.1µF ceramic chip capacitor. Do not connect to Pins 11, 12. OFB (Pin 37): Over/Under Flow Output for B bus. High when an over or under flow has occurred. At high impedance in full rate CMOS mode. REFHB (Pins 9, 10): ADC High Reference. Bypass to Pins 11, 12 with 0.1µF ceramic chip capacitor. Do not connect to Pins 5, 6. CLKOUTB (Pin 38): Data Valid Output for B bus. In demux mode with interleaved update, latch B bus data on the falling edge of CLKOUTB. In demux mode with simultaneous update, latch B bus data on the rising edge of CLKOUTB. This pin does not become high impedance in full rate CMOS mode. REFLA (Pins 11, 12): ADC Low Reference. Bypass to Pins 9, 10 with 0.1µF ceramic chip capacitor, to Pins 5, 6 with a 2.2µF ceramic capacitor and to ground with 1µF ceramic capacitor. VDD (Pins 13, 14, 15, 62, 63): 3.3V Supply. Bypass to GND with 0.1µF ceramic chip capacitors. GND (Pins 16, 61, 64): ADC Power Ground. ENC+ (Pin 17): Encode Input. The input sample starts on the positive edge. ENC – (Pin 18): Encode Complement Input. Conversion starts on the negative edge. Bypass to ground with 0.1µF ceramic for single-ended ENCODE signal. SHDN (Pin 19): Shutdown Mode Selection Pin. Connecting SHDN to GND and OE to GND results in normal operation with the outputs enabled. Connecting SHDN to GND and OE to VDD results in normal operation with the outputs at high impedance. Connecting SHDN to VDD and OE to GND results in nap mode with the outputs at high impedance. Connecting SHDN to VDD and OE to VDD results in sleep mode with the outputs at high impedance. OE (Pin 20): Output Enable Pin. Refer to SHDN pin function. DNC (Pins 21, 22, 40, 43): Do not connect these pins. CLKOUTA (Pin 39): Data Valid Output for A bus. Latch A bus data on the falling edge of CLKOUTA. DA0 - DA9 (Pins 44 to 48, 51 to 55): Digital Outputs, A bus. DA9 is the MSB. OFA (Pin 56): Over/Under Flow Output for A bus. High when an over or under flow has occurred. LVDS (Pin 57): Output Mode Selection Pin. Connecting LVDS to 0V selects full rate CMOS mode. Connecting LVDS to 1/3VDD selects demux CMOS mode with simultaneous update. Connecting LVDS to 2/3VDD selects demux CMOS mode with interleaved update. Connecting LVDS to VDD selects LVDS mode. MODE (Pin 58): Output Format and Clock Duty Cycle Stabilizer Selection Pin. Connecting MODE to 0V selects straight binary output format and turns the clock duty cycle stabilizer off. Connecting MODE to 1/3VDD selects straight binary output format and turns the clock duty cycle stabilizer on. Connecting MODE to 2/3VDD selects 2’s complement output format and turns the clock duty cycle stabilizer on. Connecting MODE to VDD selects 2’s complement output format and turns the clock duty cycle stabilizer off. 22301p 12 LTC2230/LTC2231 U U U PI FU CTIO S SENSE (Pin 59): Reference Programming Pin. Connecting SENSE to VCM selects the internal reference and a ±0.5V input range. VDD selects the internal reference and a ±1V input range. An external reference greater than 0.5V and less than 1V applied to SENSE selects an input range of ±VSENSE. ±1V is the largest valid input range. VCM (Pin 60): 1.6V Output and Input Common Mode Bias. Bypass to ground with 2.2µF ceramic chip capacitor. SHDN (Pin 19): Shutdown Mode Selection Pin. Connecting SHDN to GND and OE to GND results in normal operation with the outputs enabled. Connecting SHDN to GND and OE to VDD results in normal operation with the outputs at high impedance. Connecting SHDN to VDD and OE to GND results in nap mode with the outputs at high impedance. Connecting SHDN to VDD and OE to VDD results in sleep mode with the outputs at high impedance. GND (Exposed Pad): ADC Power Ground. The exposed pad on the bottom of the package needs to be soldered to ground. OE (Pin 20): Output Enable Pin. Refer to SHDN pin function. (LVDS Mode) OGND (Pins 25, 33, 41, 50): Output Driver Ground. AIN+ (Pins 1, 2): Positive Differential Analog Input. AIN– (Pins 3, 4): Negative Differential Analog Input. OVDD (Pins 26, 34, 42, 49): Positive Supply for the Output Drivers. Bypass to ground with 0.1µF ceramic chip capacitor. REFHA (Pins 5, 6): ADC High Reference. Bypass to Pins 7, 8 with 0.1µF ceramic chip capacitor, to Pins 11, 12 with a 2.2µF ceramic capacitor and to ground with 1µF ceramic capacitor. D0–/D0+ to D9–/D9+ (Pins 27 to 32, 37 to 40, 43 to 48, 51 to 54): LVDS Digital Outputs. All LVDS outputs require differential 100Ω termination resistors at the LVDS receiver. D9 –/D9+ is the MBS. REFLB (Pins 7, 8): ADC Low Reference. Bypass to Pins 5, 6 with 0.1µF ceramic chip capacitor. Do not connect to Pins 11, 12. CLKOUT–/CLKOUT+ (Pins 35 to 36): LVDS Data Valid Output. Latch data on rising edge of CLKOUT–, falling edge of CLKOUT+. REFHB (Pins 9, 10): ADC High Reference. Bypass to Pins 11, 12 with 0.1µF ceramic chip capacitor. Do not connect to Pins 5, 6. OF–/OF+ (Pins 55 to 56): LVDS Over/Under Flow Output. High when an over or under flow has occurred. REFLA (Pins 11, 12): ADC Low Reference. Bypass to Pins 9, 10 with 0.1µF ceramic chip capacitor, to Pins 5, 6 with a 2.2µF ceramic capacitor and to ground with 1µF ceramic capacitor. VDD (Pins 13, 14, 15, 62, 63): 3.3V Supply. Bypass to GND with 0.1µF ceramic chip capacitors. GND (Pins 16, 61, 64): ADC Power Ground. ENC+ (Pin 17): Encode Input. The input sample starts on the positive edge. ENC– (Pin 18): Encode Complement Input. Conversion starts on the negative edge. Bypass to ground with 0.1µF ceramic for single-ended ENCODE signal. DNC (Pins 21, 22, 23, 24): Do not connect these pins. LVDS (Pin 57): Output Mode Selection Pin. Connecting LVDS to 0V selects full rate CMOS mode. Connecting LVDS to 1/3VDD selects demux CMOS mode with simultaneous update. Connecting LVDS to 2/3VDD selects demux CMOS mode with interleaved update. Connecting LVDS to VDD selects LVDS mode. MODE (Pin 58): Output Format and Clock Duty Cycle Stabilizer Selection Pin. Connecting MODE to 0V selects straight binary output format and turns the clock duty cycle stabilizer off. Connecting MODE to 1/3VDD selects straight binary output format and turns the clock duty cycle stabilizer on. Connecting MODE to 2/3VDD selects 2’s complement output format and turns the clock duty cycle stabilizer on. Connecting MODE to VDD selects 2’s complement output format and turns the clock duty cycle stabilizer off. 22301p 13 LTC2230/LTC2231 U U U PI FU CTIO S VCM (Pin 60): 1.6V Output and Input Common Mode Bias. Bypass to ground with 2.2µF ceramic chip capacitor. SENSE (Pin 59): Reference Programming Pin. Connecting SENSE to VCM selects the internal reference and a ±0.5V input range. VDD selects the internal reference and a ±1V input range. An external reference greater than 0.5V and less than 1V applied to SENSE selects an input range of ±VSENSE. ±1V is the largest valid input range. GND (Exposed Pad): ADC Power Ground. The exposed pad on the bottom of the package needs to be soldered to ground. W FUNCTIONAL BLOCK DIAGRA U U AIN+ AIN– VCM FIRST PIPELINED ADC STAGE (4 BITS) INPUT S/H SECOND PIPELINED ADC STAGE (3 BITS) THIRD PIPELINED ADC STAGE (3 BITS) FOURTH PIPELINED ADC STAGE (3 BITS) FIFTH PIPELINED ADC STAGE (3 BITS) 1.6V REFERENCE 2.2µF SHIFT REGISTER AND CORRECTION RANGE SELECT REFH SENSE REFL INTERNAL CLOCK SIGNALS OVDD REF BUF DIFFERENTIAL INPUT LOW JITTER CLOCK DRIVER DIFF REF AMP REFLB REFHA 2.2µF 0.1µF CONTROL LOGIC • • • OUTPUT DRIVERS + OF – + D9 – + – + – D0 CLKOUT 22201 F01 REFLA REFHB OGND ENC+ ENC– M0DE LVDS SHDN OEL 0.1µF 1µF 1µF Figure 1. Functional Block Diagram W UW TI I G DIAGRA S LVDS Output Mode Timing All Outputs Are Differential and Have LVDS Levels tAP ANALOG INPUT N+4 N+2 N N+3 tH N+1 tL ENC – ENC + tD N–5 D0-D9, OF CLOCKOUT – N–4 N–3 N–2 N–1 tC CLOCKOUT + 22201 TD01 22301p 14 LTC2230/LTC2231 W UW TI I G DIAGRA S Full-Rate CMOS Output Mode Timing All Outputs Are Single-Ended and Have CMOS Levels tAP ANALOG INPUT N+4 N+2 N N+3 tH N+1 tL ENC – ENC + tD N–5 DA0-DA9, OFA N–4 N–3 N–2 N–1 tC CLOCKOUTB CLOCKOUTA HIGH IMPEDANCE DB0-DB9, OFB 22201 TD02 Demultiplexed CMOS Outputs with Interleaved Update All Outputs Are Single-Ended and Have CMOS Levels tAP ANALOG INPUT N+4 N+2 N N+3 tH N+1 tL ENC – ENC + tD N–5 DA0-DA9, OFA N–3 N–1 tD N–6 DB0-DB9, OFB N–4 tC N–2 tC CLOCKOUTB CLOCKOUTA 22201 TD03 Demultiplexed CMOS Outputs with Simultaneous Update All Outputs Are Single-Ended and Have CMOS Levels tAP ANALOG INPUT N+4 N+2 N N+3 tH N+1 tL ENC – ENC + tD DA0-DA9, OFA N–6 N–4 N–2 N–5 N–3 N–1 tD DB0-DB9, OFB tC CLOCKOUTB CLOCKOUTA 22201 TD04 22301p 15 LTC2230/LTC2231 U U W U APPLICATIO S I FOR ATIO DYNAMIC PERFORMANCE input tone to the RMS value of the largest 3rd order intermodulation product. Signal-to-Noise Plus Distortion Ratio The signal-to-noise plus distortion ratio [S/(N + D)] is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components at the ADC output. The output is band limited to frequencies above DC to below half the sampling frequency. Spurious Free Dynamic Range (SFDR) Signal-to-Noise Ratio Input Bandwidth The signal-to-noise ratio (SNR) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components except the first five harmonics and DC. The input bandwidth is that input frequency at which the amplitude of the reconstructed fundamental is reduced by 3dB for a full scale input signal. Spurious free dynamic range is the peak harmonic or spurious noise that is the largest spectral component excluding the input signal and DC. This value is expressed in decibels relative to the RMS value of a full scale input signal. Aperture Delay Time Total Harmonic Distortion Total harmonic distortion is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency. THD is expressed as: 2 2 2 2 THD = 20Log √(V2 + V3 + V4 + . . . Vn )/V1 where V1 is the RMS amplitude of the fundamental frequency and V2 through Vn are the amplitudes of the second through nth harmonics. The THD calculated in this data sheet uses all the harmonics up to the fifth. Intermodulation Distortion If the ADC input signal consists of more than one spectral component, the ADC transfer function nonlinearity can produce intermodulation distortion (IMD) in addition to THD. IMD is the change in one sinusoidal input caused by the presence of another sinusoidal input at a different frequency. If two pure sine waves of frequencies fa and fb are applied to the ADC input, nonlinearities in the ADC transfer function can create distortion products at the sum and difference frequencies of mfa ± nfb, where m and n = 0, 1, 2, 3, etc. The 3rd order intermodulation products are 2fa + fb, 2fb + fa, 2fa – fb and 2fb – fa. The intermodulation distortion is defined as the ratio of the RMS value of either The time from when a rising ENC+ equals the ENC– voltage to the instant that the input signal is held by the sample and hold circuit. Aperture Delay Jitter The variation in the aperture delay time from conversion to conversion. This random variation will result in noise when sampling an AC input. The signal to noise ratio due to the jitter alone will be: SNRJITTER = –20log (2pi) • fIN • tJITTER CONVERTER OPERATION As shown in Figure 1, the LTC2230/LTC2231 is a CMOS pipelined multistep converter. The converter has five pipelined ADC stages; a sampled analog input will result in a digitized value five cycles later (see the Timing Diagram section). For optimal AC performance the analog inputs should be driven differentially. For cost sensitive applications, the analog inputs can be driven single-ended with slightly worse harmonic distortion. The encode input is differential for improved common mode noise immunity. The LTC2230/LTC2231 has two phases of operation, determined by the state of the differential ENC+/ENC– input pins. For brevity, the text will refer to ENC+ greater than ENC– as ENC high and ENC+ less than ENC– as ENC low. 22301p 16 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO Each pipelined stage shown in Figure 1 contains an ADC, a reconstruction DAC and an interstage residue amplifier. In operation, the ADC quantizes the input to the stage and the quantized value is subtracted from the input by the DAC to produce a residue. The residue is amplified and output by the residue amplifier. Successive stages operate out of phase so that when the odd stages are outputting their residue, the even stages are acquiring that residue and vice versa. When ENC is low, the analog input is sampled differentially directly onto the input sample-and-hold capacitors, inside the “Input S/H” shown in the block diagram. At the instant that ENC transitions from low to high, the sampled input is held. While ENC is high, the held input voltage is buffered by the S/H amplifier which drives the first pipelined ADC stage. The first stage acquires the output of the S/H during this high phase of ENC. When ENC goes back low, the first stage produces its residue which is acquired by the second stage. At the same time, the input S/H goes back to acquiring the analog input. When ENC goes back high, the second stage produces its residue which is acquired by the third stage. An identical process is repeated for the third and fourth stages, resulting in a fourth stage residue that is sent to the fifth stage ADC for final evaluation. Each ADC stage following the first has additional range to accommodate flash and amplifier offset errors. Results from all of the ADC stages are digitally synchronized such that the results can be properly combined in the correction logic before being sent to the output buffer. SAMPLE/HOLD OPERATION AND INPUT DRIVE Sample/Hold Operation Figure 2 shows an equivalent circuit for the LTC2230/ LTC2231 CMOS differential sample-and-hold. The analog inputs are connected to the sampling capacitors (CSAMPLE) through NMOS transistors. The capacitors shown attached to each input (CPARASITIC) are the summation of all other capacitance associated with each input. During the sample phase when ENC is low, the transistors connect the analog inputs to the sampling capacitors and they charge to, and track the differential input voltage. When ENC transitions from low to high, the sampled input voltage is held on the sampling capacitors. During the hold phase when ENC is high, the sampling capacitors are disconnected from the input and the held voltage is passed to the ADC core for processing. As ENC transitions from high to low, the inputs are reconnected to the sampling capacitors to acquire a new sample. Since the sampling capacitors still hold the previous sample, a charging glitch proportional to the change in voltage between samples will be seen at this time. If the change between the last sample and the new sample is small, the charging glitch seen at the input will be small. If the input change is large, such as the change seen with input frequencies near Nyquist, then a larger charging glitch will be seen. LTC2230/LTC2231 VDD AIN+ CSAMPLE 1.6pF 15Ω CPARASITIC 1pF VDD AIN– CSAMPLE 1.6pF 15Ω CPARASITIC 1pF VDD 1.6V 6k ENC+ ENC– 6k 1.6V 22201 F02 Figure 2. Equivalent Input Circuit Single-Ended Input For cost sensitive applications, the analog inputs can be driven single-ended. With a single-ended input the harmonic distortion and INL will degrade, but the SNR and DNL will remain unchanged. For a single-ended input, AIN+ should be driven with the input signal and AIN– should be connected to 1.6V or VCM. Common Mode Bias For optimal performance the analog inputs should be driven differentially. Each input should swing ±0.5V for the 2V range or ±0.25V for the 1V range, around a common mode voltage of 1.6V. The VCM output pin (Pin 22301p 17 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO 60) may be used to provide the common mode bias level. VCM can be tied directly to the center tap of a transformer to set the DC input level or as a reference level to an op amp differential driver circuit. The VCM pin must be bypassed to ground close to the ADC with a 2.2µF or greater capacitor. width of most op amps will limit the SFDR at high input frequencies. Input Drive Impedance The 25Ω resistors and 12pF capacitor on the analog inputs serve two purposes: isolating the drive circuitry from the sample-and-hold charging glitches and limiting the wideband noise at the converter input. For input frequencies higher than 100MHz, the capacitor may need to be decreased to prevent excessive signal loss. As with all high performance, high speed ADCs, the dynamic performance of the LTC2230/LTC2231 can be influenced by the input drive circuitry, particularly the second and third harmonics. Source impedance and input reactance can influence SFDR. At the falling edge of ENC, the sample-and-hold circuit will connect the 1.6pF sampling capacitor to the input pin and start the sampling period. The sampling period ends when ENC rises, holding the sampled input on the sampling capacitor. Ideally the input circuitry should be fast enough to fully charge the sampling capacitor during the sampling period 1/(2FENCODE); however, this is not always possible and the incomplete settling may degrade the SFDR. The sampling glitch has been designed to be as linear as possible to minimize the effects of incomplete settling. For the best performance, it is recommended to have a source impedance of 100Ω or less for each input. The source impedance should be matched for the differential inputs. Poor matching will result in higher even order harmonics, especially the second. Input Drive Circuits Figure 3 shows the LTC2230/LTC2231 being driven by an RF transformer with a center tapped secondary. The secondary center tap is DC biased with VCM, setting the ADC input signal at its optimum DC level. Figure 3 shows a 1:1 turns ratio transformer. Other turns ratios can be used if the source impedance seen by the ADC does not exceed 100Ω for each ADC input. A disadvantage of using a transformer is the loss of low frequency response. Most small RF transformers have poor performance at frequencies below 1MHz. Figure 4 demonstrates the use of a differential amplifier to convert a single ended input signal into a differential input signal. The advantage of this method is that it provides low frequency input response; however, the limited gain band- Figure 5 shows a single-ended input circuit. The impedance seen by the analog inputs should be matched. This circuit is not recommended if low distortion is required. VCM 2.2µF 0.1µF ANALOG INPUT T1 1:1 25Ω 25Ω AIN+ 0.1µF AIN+ LTC2230/ LTC2231 12pF 25Ω AIN– 25Ω AIN– T1 = MA/COM ETC1-1T RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 22301 F03 Figure 3. Single-Ended to Differential Conversion Using a Transformer VCM HIGH SPEED DIFFERENTIAL 25Ω AMPLIFIER ANALOG INPUT + AIN+ AIN+ + LTC2230/ LTC2231 12pF CM – 2.2µF – AIN– 25Ω AIN– AMPLIFIER = LTC6600-20, AD8138, ETC. 22301 F04 Figure 4. Differential Drive with an Amplifier VCM 10k 0.1µF ANALOG INPUT 2.2µF 10k 25Ω AIN+ AIN+ 12pF 25Ω LTC2230/ LTC2231 AIN– AIN– 0.1µF 22301 F05 Figure 5. Single-Ended Drive 22301p 18 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO The AIN+ and AIN– inputs each have two pins to reduce package inductance. The two AIN+ and the two AIN– pins should be shorted together. For input frequencies above 100MHz the input circuits of Figure 6, 7 and 8 are recommended. The balun transformer gives better high frequency response than a flux coupled center tapped transformer. The coupling capacitors allow the analog inputs to be DC biased at 1.6V. In Figure 8 the series inductors are impedance matching elements that maximize the ADC bandwidth. VCM 2.2µF 0.1µF ANALOG INPUT 25Ω 12Ω AIN+ 0.1µF AIN+ T1 0.1µF LTC2230/ LTC2231 8pF 25Ω 12Ω AIN– AIN– T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 22301 F06 Figure 6. Recommended Front End Circuit for Input Frequencies Between 100MHz and 250MHz VCM 2.2µF 0.1µF AIN+ ANALOG INPUT 25Ω 0.1µF AIN+ LTC2230/ LTC2231 Reference Operation Figure 9 shows the LTC2230/LTC2231 reference circuitry consisting of a 1.6V bandgap reference, a difference amplifier and switching and control circuit. The internal voltage reference can be configured for two pin selectable input ranges of 2V (±1V differential) or 1V (±0.5V differential). Tying the SENSE pin to VDD selects the 2V range; typing the SENSE pin to VCM selects the 1V range. The 1.6V bandgap reference serves two functions: its output provides a DC bias point for setting the common mode voltage of any external input circuitry; additionally, the reference is used with a difference amplifier to generate the differential reference levels needed by the internal ADC circuitry. An external bypass capacitor is required for the 1.6V reference output, VCM. This provides a high frequency low impedance path to ground for internal and external circuitry. The difference amplifier generates the high and low reference for the ADC. High speed switching circuits are connected to these outputs and they must be externally bypassed. Each output has four pins: two each of REFHA and REFHB for the high reference and two each of REFLA and REFLB for the low reference. The multiple output pins are needed to reduce package inductance. Bypass capacitors must be connected as shown in Figure 9. LTC2230/LTC2231 T1 0.1µF AIN– 25Ω 1.6V AIN– T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 4.7nH 0.1µF T1 0.1µF 1V AIN+ AIN+ TIE TO VDD FOR 2V RANGE; TIE TO VCM FOR 1V RANGE; RANGE = 2 • VSENSE FOR 0.5V < VSENSE < 1V 1µF 2.2µF 25Ω LTC2230/ LTC2231 4.7nH SENSE REFLB 0.1µF REFHA BUFFER INTERNAL ADC HIGH REFERENCE 2.2µF DIFF AMP AIN– 1µF REFLA AIN– T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 0.5V RANGE DETECT AND CONTROL 2pF 25Ω 1.6V BANDGAP REFERENCE 22301 F07 VCM 0.1µF 4Ω 2.2µF Figure 7. Recommended Front End Circuit for Input Frequencies Between 250MHz and 500MHz ANALOG INPUT VCM 22301 F08 Figure 8. Recommended Front End Circuit for Input Frequencies Above 500MHz 0.1µF REFHB INTERNAL ADC LOW REFERENCE 22301 F09 Figure 9. Equivalent Reference Circuit 22301p 19 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO Other voltage ranges in between the pin selectable ranges can be programmed with two external resistors as shown in Figure 10. An external reference can be used by applying its output directly or through a resistor divider to SENSE. It is not recommended to drive the SENSE pin with a logic device. The SENSE pin should be tied to the appropriate level as close to the converter as possible. If the SENSE pin is driven externally, it should be bypassed to ground as close to the device as possible with a 1µF ceramic capacitor. 1.6V 2. Use as large an amplitude as possible; if transformer coupled use a higher turns ratio to increase the amplitude. 3. If the ADC is clocked with a sinusoidal signal, filter the encode signal to reduce wideband noise. 4. Balance the capacitance and series resistance at both encode inputs so that any coupled noise will appear at both inputs as common mode noise. The encode inputs have a common mode range of 1.1V to 2.5V. Each input may be driven from ground to VDD for single-ended drive. VCM LTC2230/LTC2231 2.2µF VDD 12k 0.8V 12k SENSE LTC2230/ LTC2231 TO INTERNAL ADC CIRCUITS 1µF VDD 6k 22301 F10 ENC+ Figure 10. 1.6V Range ADC Input Range 0.1µF 1:4 CLOCK INPUT VDD 50Ω The input range can be set based on the application. The 2V input range will provide the best signal-to-noise performance while maintaining excellent SFDR. The 1V input range will have better SFDR performance, but the SNR will degrade by 1.7dB. See the Typical Performance Characteristics section. 1.6V BIAS 1.6V BIAS 6k ENC– 22201 F11 Figure 11. Transformer Driven ENC+/ENC– Driving the Encode Inputs Maximum and Minimum Encode Rates The noise performance of the LTC2230/LTC2231 can depend on the encode signal quality as much as on the analog input. The ENC+/ENC– inputs are intended to be driven differentially, primarily for noise immunity from common mode noise sources. Each input is biased through a 6k resistor to a 1.6V bias. The bias resistors set the DC operating point for transformer coupled drive circuits and can set the logic threshold for single-ended drive circuits. The maximum encode rate for the LTC2230/LTC2231 is 170Msps (LTC2230) and 135Msps (LTC2231). For the ADC to operate properly, the encode signal should have a 50% (±5%) duty cycle. Each half cycle must have at least 2.8ns (LTC2230) or 3.5ns (LTC2231) for the ADC internal circuitry to have enough settling time for proper operation. Achieving a precise 50% duty cycle is easy with differential sinusoidal drive using a transformer or using symmetric differential logic such as PECL or LVDS. Any noise present on the encode signal will result in additional aperture jitter that will be RMS summed with the inherent ADC aperture jitter. In applications where jitter is critical (high input frequencies) take the following into consideration: 1. Differential drive should be used. An optional clock duty cycle stabilizer circuit can be used if the input clock has a non 50% duty cycle. This circuit uses the rising edge of the ENC+ pin to sample the analog input. The falling edge of ENC+ is ignored and the internal falling edge is generated by a phase-locked loop. The input clock duty cycle can vary from 30% to 70% and the clock duty cycle stabilizer will maintain a constant 50% internal 22301p 20 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO duty cycle. If the clock is turned off for a long period of time, the duty cycle stabilizer circuit will require a hundred clock cycles for the PLL to lock onto the input clock. To use the clock duty cycle stabilizer, the MODE pin should be connected to 1/3VDD or 2/3VDD using external resistors. connected to GND, 1/3VDD, 2/3VDD or VDD. An external resistor divider can be used to set the 1/3VDD or 2/3VDD logic values. Table 1 shows the logic states for the LVDS pin. The lower limit of the LTC2230/LTC2231 sample rate is determined by droop of the sample-and-hold circuits. The pipelined architecture of this ADC relies on storing analog signals on small valued capacitors. Junction leakage will discharge the capacitors. The specified minimum operating frequency for the LTC2230/LTC2231 is 1Msps. LVDS Digital Output Mode GND Full-Rate CMOS 1/3VDD Demultiplexed CMOS, Simultaneous Update 2/3VDD Demultiplexed CMOS, Interleaved Update VDD LVDS Digital Output Buffers (CMOS Modes) ENC+ VTHRESHOLD = 1.6V 1.6V ENC – LTC2230/ LTC2231 0.1µF 22301 F12a Figure 12a. Single-Ended ENC Drive, Not Recommended for Low Jitter 3.3V MC100LVELT22 Table 1. LVDS Pin Function Figure 13a shows an equivalent circuit for a single output buffer in the CMOS output mode. Each buffer is powered by OVDD and OGND, isolated from the ADC power and ground. The additional N-channel transistor in the output driver allows operation down to low voltages. The internal resistor in series with the output makes the output appear as 50Ω to external circuitry and may eliminate the need for external damping resistors. 3.3V 130Ω Q0 130Ω LTC2230/LTC2231 OVDD ENC+ D0 VDD 0.5V TO VDD VDD 0.1µF ENC– Q0 83Ω LTC2230/ LTC2231 OVDD 83Ω 22301 F12b Figure 12b. ENC Drive Using a CMOS to PECL Translator DATA FROM LATCH PREDRIVER LOGIC 43Ω TYPICAL DATA OUTPUT OE OGND DIGITAL OUTPUTS 22301 F13a Digital Output Modes Figure 13a. Digital Output Buffer in CMOS Mode The LTC2230/LTC2231 can operate in several digital output modes: LVDS, CMOS running at full speed, and CMOS demultiplexed onto two buses, each of which runs at half speed. In the demultiplexed CMOS modes the two buses (referred to as bus A and bus B) can either be updated on alternate clock cycles (interleaved mode) or simultaneously (simultaneous mode). For details on the clock timing, refer to the timing diagrams. As with all high speed/high resolution converters, the digital output loading can affect the performance. The digital outputs of the LTC2230/LTC2231 should drive a minimal capacitive load to avoid possible interaction between the digital outputs and sensitive input circuitry. The output should be buffered with a device such as an ALVCH16373 CMOS latch. For full speed operation the capacitive load should be kept under 10pF. The LVDS pin selects which digital output mode the part uses. This pin has a four-level logic input which should be Lower OVDD voltages will also help reduce interference from the digital outputs. 22301p 21 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO Digital Output Buffers (LVDS Mode) Overflow Bit Figure 13b shows an equivalent circuit for a differential output pair in the LVDS output mode. A 3.5mA current is steered from OUT+ to OUT– or vice versa which creates a ±350mV differential voltage across the 100Ω termination resistor at the LVDS receiver. A feedback loop regulates the common mode output voltage to 1.25V. For proper operation each LVDS output pair needs an external 100Ω termination resistor, even if the signal is not used (such as OF+/OF– or CLKOUT+/CLKOUT–). To minimize noise the PC board traces for each LVDS output pair should be routed close together. To minimize clock skew all LVDS PC board traces should have about the same length. An overflow output bit indicates when the converter is overranged or underranged. In CMOS mode, a logic high on the OFA pin indicates an overflow or underflow on the A data bus, while a logic high on the OFB pin indicates an overflow or underflow on the B data bus. In LVDS mode, a differential logic high on the OF+/OF– pins indicates an overflow or underflow. LTC2230/LTC2231 OVDD D D OUT+ – + 10k 10k 100Ω 1.25V LVDS RECEIVER OUT– D D 3.5mA OGND Output Clock The ADC has a delayed version of the ENC+ input available as a digital output, CLKOUT. The CLKOUT pin can be used to synchronize the converter data to the digital system. This is necessary when using a sinusoidal encode. In all CMOS modes, A bus data will be updated just after CLKOUTA rises and can be latched on the falling edge of CLKOUTA. In demux CMOS mode with interleaved update, B bus data will be updated just after CLKOUTB rises and can be latched on the falling edge of CLKOUTB. In demux CMOS mode with simultaneous update, B bus data will be updated just after CLKOUTB falls and can be latched on the rising edge of CLKOUTB. In LVDS mode, data will be updated just after CLKOUT+/CLKOUT– rises and can be latched on the falling edge of CLKOUT+/CLKOUT–. 22301 F13b Figure 13b. Digital Output in LVDS Mode Data Format The LTC2230/LTC2231 parallel digital output can be selected for offset binary or 2’s complement format. The format is selected with the MODE pin. Connecting MODE to GND or 1/3VDD selects straight binary output format. Connecting MODE to 2/3VDD or VDD selects 2’s complement output format. An external resistor divider can be used to set the 1/3VDD or 2/3VDD logic values. Table 2 shows the logic states for the MODE pin. Table 2. MODE Pin Function Output Driver Power Separate output power and ground pins allow the output drivers to be isolated from the analog circuitry. The power supply for the digital output buffers, OVDD, should be tied to the same power supply as for the logic being driven. For example if the converter is driving a DSP powered by a 1.8V supply then OVDD should be tied to that same 1.8V supply. In the CMOS output mode, OVDD can be powered with any voltage up to the VDD of the part. OGND can be powered with any voltage from GND up to 1V and must be less than OVDD. The logic outputs will swing between OGND and OVDD. In the LVDS output mode, OVDD should be connected to a 3.3V supply and OGND should be connected to GND. MODE Pin Output Format Clock Duty Cycle Stablizer 0 Straight Binary Off Output Enable 1/3VDD Straight Binary On 2/3VDD 2’s Complement On VDD 2’s Complement Off The outputs may be disabled with the output enable pin, OE. In CMOS or LVDS output modes OE high disables all data outputs including OF and CLKOUT. The data access and bus 22301p 22 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO relinquish times are too slow to allow the outputs to be enabled and disabled during full speed operation. The output Hi-Z state is intended for use during long periods of inactivity. printed circuit board should ensure that digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital track alongside an analog signal track or underneath the ADC. The Hi-Z state is not a truly open circuit; the output pins that make an LVDS output pair have a 20k resistance between them. Therefore in the CMOS output mode, adjacent data bits will have 20k resistance in between them, even in the Hi-Z state. High quality ceramic bypass capacitors should be used at the VDD, OVDD, VCM, REFHA, REFHB, REFLA and REFLB pins as shown in the block diagram on the front page of this data sheet. Bypass capacitors must be located as close to the pins as possible. Of particular importance are the capacitors between REFHA and REFLB and between REFHB and REFLA. These capacitors should be as close to the device as possible (1.5mm or less). Size 0402 ceramic capacitors are recommended. The 2.2µF capacitor between REFHA and REFLA can be somewhat further away. The traces connecting the pins and bypass capacitors must be kept short and should be made as wide as possible. Sleep and Nap Modes The converter may be placed in shutdown or nap modes to conserve power. Connecting SHDN to GND results in normal operation. Connecting SHDN to VDD and OE to VDD results in sleep mode, which powers down all circuitry including the reference and typically dissipates 1mW. When exiting sleep mode it will take milliseconds for the output data to become valid because the reference capacitors have to recharge and stabilize. Connecting SHDN to VDD and OE to GND results in nap mode, which typically dissipates 35mW. In nap mode, the on-chip reference circuit is kept on, so that recovery from nap mode is faster than that from sleep mode, typically taking 100 clock cycles. In both sleep and nap mode all digital outputs are disabled and enter the Hi-Z state. GROUNDING AND BYPASSING The LTC2230/LTC2231 requires a printed circuit board with a clean unbroken ground plane. A multilayer board with an internal ground plane is recommended. Layout for the The LTC2230/LTC2231 differential inputs should run parallel and close to each other. The input traces should be as short as possible to minimize capacitance and to minimize noise pickup. HEAT TRANSFER Most of the heat generated by the LTC2230/LTC2231 is transferred from the die through the bottom-side exposed pad and package leads onto the printed circuit board. For good electrical and thermal performance, the exposed pad should be soldered to a large grounded pad on the PC board. It is critical that all ground pins are connected to a ground plane of sufficient area. 22301p 23 24 VCM R27 1k J9 R29 1k 1/3VDD R30 1k GND ANALOG INPUT MODE VDD R28 1k 2/3VDD C23 0.1µF C27 0.1µF JP19 JP14 JP13 JP7 T1 ETC1-1T C39 0.1µF R11 24.9k R12 24.9k R10 24.9k R9 24.9k C22 0.1µF 1 2 3 4 AIN– 5 6 C16 C17 0.1µF 7 1µF 8 C19 2.2µF 9 10 C18 C11 VDD 1µF 0.1µF 11 12 C21 62 0.1µF 63 13 VDD 14 15 C24 VDD JP3 0.1µF 17 CLK 18 GND SHDN CLK 19 20 25 C29 33 2.2µF VDD GND 41 VDD 50 0E JP1 60 VCM JP20 SENSE 59 VDD 16 VCM JP21 61 VCM 64 JP22 EXT 58 REF 57 C35 VDD 0.1µF C7 12pF AIN– AIN+ C30 0.1µF C31 0.1µF C32 0.1µF C33 0.1µF C34 4.7µF 56 55 54 53 52 51 48 47 46 45 44 43 40 39 38 37 36 35 32 31 30 29 28 27 24 23 22 21 49 42 34 26 VDD ENCODE INPUT VDD 3.3V VDD R7 100Ω C26 0.1µF 1 A0 2 A1 3 A2 4 A3 C4 0.1µF R23 100Ω R16 100Ω T2 ETC1-1T C3 4.7µF R24 100Ω R15 100Ω R8 100Ω C20 0.1µF JP4 8 VCC 7 WP 6 SCL 5 SDA R2 4.99k 1% R21 100Ω ENABLE R20 100Ω R18 100Ω CLK C25 33pF CLK R4 4.99k 1% R3 4.99k 1% R19 100Ω R17 100Ω SDA SCL VSS VCC_IN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 GND GND EN/12 RUN1– RUN1+ RUN2+ RUN2– RUN3– RUN3+ RUN4+ RUN4– VCC EN RUN5– RUN5+ RUN6+ RUN6– RUN7– RUN7+ RUN8+ RUN8– EN/34 GND VBB C1 0.1µF OPT VCC VCC 3.3V VCC VCC Evaluation Circuit Schematic of the LTC2230 J6 R25 100Ω R14 100Ω PWR GND GND R26 100Ω R13 100Ω GND GND EN/12 RUN1– RUN1+ RUN2+ RUN2– RUN3– RUN3+ RUN4+ RUN4– VCC EN RUN5– RUN5+ RUN6+ RUN6– RUN7– RUN7+ RUN8+ RUN8– EN/34 GND VBB C2 0.1µF VCC VCC EN/78 DOUT1– DOUT1+ DOUT2+ DOUT2– DOUT3– DOUT3+ DOUT4+ DOUT4– GND GND DOUT5– DOUT5+ DOUT6+ DOUT6– DOUT7– DOUT7+ DOUT8+ DOUT8– EN/56 VCC VCC VCC VCC EN/78 DOUT1– DOUT1+ DOUT2+ DOUT2– DOUT3– DOUT3+ DOUT4+ DOUT4– GND GND DOUT5– DOUT5+ DOUT6+ DOUT6– DOUT7– DOUT7+ DOUT8+ DOUT8– EN/56 VCC VCC C5 0.1µF VDD 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 VCC 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 C6 0.1µF L1 VCC VCC C8 0.1µF C9 0.1µF C5 4.7µF MURATA BLM18BB470SN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 C10 0.1µF EDGE-CON-100 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 C12 0.1µF R6 4.7k C36 4.7µF VCC ENABLE SDA VCC_IN VSS SCL U U W AIN+ LTC2230 AIN+ OF+/OFA AIN+ OF–/DA11 AIN– D11+/DA10 AIN– D11–/DA9 REFHA D10+/DA8 REFHA D10–/DA7 REFLB D9+/DA6 REFLB D9–/DA5 REFHB D8+/DA4 REFHB D8–/DA3 REFLA D7+/DA2 REFLA D7–/DA1 VDD D6+/DA0 VDD D6–/CLKOUTA + VDD D5 /CLKOUTB VDD DB5–/OFB VDD CLKOUT+/DB11 ENC+ CLKOUT–/DB10 ENC– D4+/DB9 SHDN D4–/DB8 OEL D3+/DB7 OGND D3–/DB6 OGND D2+/DB5 OGND D2–/DB4 OGND D1+/DB3 VCM D1–/DB2 SENSE D0+/DB1 GND D0–/DB0 GND OVDD GND OVDD MODE OVDD LVDS OVDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 APPLICATIO S I FOR ATIO U R1 100Ω LTC2230/LTC2231 22301p LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO Silkscreen Top Layer 1 Component Side Layer 2 GND Plane 22301p 25 LTC2230/LTC2231 U W U U APPLICATIO S I FOR ATIO Layer 3 Power Plane Layer 4 Bottom Side 22301p 26 LTC2230/LTC2231 U PACKAGE DESCRIPTIO UP Package 64-Lead Plastic QFN (9mm × 9mm) (Reference LTC DWG # 05-08-1705) 0.70 ±0.05 7.15 ±0.05 8.10 ±0.05 9.50 ±0.05 (4 SIDES) NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION WNJR-5 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 4. EXPOSED PAD SHALL BE SOLDER PLATED 5. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 9 .00 ± 0.10 (4 SIDES) 0.75 ± 0.05 R = 0.115 TYP 63 64 0.40 ± 0.10 PIN 1 TOP MARK (SEE NOTE 5) 1 2 PIN 1 CHAMFER 7.15 ± 0.10 (4-SIDES) (UP64) QFN 0903 0.25 ± 0.05 0.200 REF 0.50 BSC 0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD 22301p Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTC2230/LTC2231 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1747 12-Bit, 80Msps ADC 72dB SNR, 87dB SFDR, 48-Pin TSSOP Package LTC1748 14-Bit, 80Msps ADC 76.3dB SNR, 90dB SFDR, 48-Pin TSSOP Package LTC1749 12-Bit, 80Msps Wideband ADC Up to 500MHz IF Undersampling, 87dB SFDR LTC1750 14-Bit, 80Msps Wideband ADC Up to 500MHz IF Undersampling, 90dB SFDR LTC2220 12-Bit, 170Msps ADC 890mW, 67.5dB SNR, 9mm x 9mm QFN Package LTC2221 12-Bit, 135Msps ADC 660mW, 67.5dB SNR, 9mm x 9mm QFN Package LTC2222 12-Bit, 105Mspss ADC 475mW, 67.9dB SNR, 7mm x 7mm QFN Package LT5514 Ultralow Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain 450MHz 1dB BW, 47dB OIP3, Digital Gain Control 10.5dB to 33dB in 1.5dB/Step 22301p 28 Linear Technology Corporation LT/TP 0604 1K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2004