TI TAS3004

Data
Manual
2001
Digital Audio Products
SLAS325
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its products to the specifications applicable at the time of sale in accordance with
TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary
to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except
those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
products or services might be or are used. TI’s publication of information regarding any third party’s products
or services does not constitute TI’s approval, license, warranty or endorsement thereof.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation
or reproduction of this information with alteration voids all warranties provided for an associated TI product or
service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service,
is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2001, Texas Instruments Incorporated
Contents
Section
1
2
3
4
Title
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.3
Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
1.4
Terminal Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
1.5
Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
Audio Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
2.1
Serial Interface Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
2.2
ADC Digital Output Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
2.2.1
MSB First, Right-Justified Serial Interface
Format—Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
2.2.2
I2S Serial Interface Format—Normal Mode . . . . . . . . . . . . . 2–3
2.2.3
MSB Left-Justified Serial Interface Format—Normal Mode 2–4
2.3
ADC Digital Output Mode—Monaural . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
2.3.1
MSB First, Right-Justified Serial Interface
Format—Monaural ADC Mode, B Left Input Selected . . . . 2–5
2.3.2
I2S Serial Interface Format—Monaural ADC Mode,
B Left Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
2.3.3
MSB Left-Justified Serial Interface Format—Monaural
ADC Mode, B Left Input Selected . . . . . . . . . . . . . . . . . . . . . 2–7
2.3.4
MSB First, Right-Justified Serial Interface
Format—Monaural ADC Mode, B Right Input Selected . . 2–8
2.3.5
I2S Serial Interface Format—Monaural ADC Mode, B Right
Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
2.3.6
MSB Left-Justified Serial Interface Format—Monaural
ADC Mode, B Right Input Selected . . . . . . . . . . . . . . . . . . . . 2–10
2.4
Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11
Analog Input/Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.1
Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.2
Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.2.1
Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.2.2
Analog Output With Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
3.2.3
Reference Voltage Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3
Audio Control/Enhancement Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
4.1
Soft Volume Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
4.2
Software Soft Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
4.3
Input Mixer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
4.4
Mono Mixer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
4.5
Treble Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
iii
4.6
4.7
4.8
4.9
5
6
7
8
iv
Bass Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
De-Emphasis (DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Control Register Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic Loudness Contour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.1
Loudness Biquads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.2
Loudness Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.3
Loudness Contour Operation . . . . . . . . . . . . . . . . . . . . . . . . .
4.10 Dynamic Range Compression/Expansion . . . . . . . . . . . . . . . . . . . . . . .
4.11 AllPass Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.12 Main Control Register 2 (43h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filter Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
Biquad Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.1
Filter Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.2
Biquad Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Serial Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
I2C Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.1
Write Cycle Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.2
TAS3004 I2C Readback Example . . . . . . . . . . . . . . . . . . . . .
6.3.3
I2C Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4
SMBus Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.1
Block Write Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.2
Write Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.3
Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.4
TAS3004 SMBus Readback . . . . . . . . . . . . . . . . . . . . . . . . . .
Microcontroller Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2
Power-Up/Power-Down Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1
Power-Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.3
Reset Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.4
Fast Load Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.5
Codec Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3
Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.1
Power-Down Timing Sequence . . . . . . . . . . . . . . . . . . . . . . .
7.4
Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5
Internal Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.6
GPI Terminal Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.6.1
Switch Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.6.2
GPI Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.7
External EPROM Memory Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1
Absolute Maximum Ratings Over Operating Temperature Ranges .
4–3
4–3
4–4
4–5
4–5
4–5
4–5
4–6
4–6
4–7
5–1
5–1
5–1
5–1
6–1
6–1
6–1
6–2
6–2
6–3
6–3
6–4
6–4
6–4
6–5
6–5
7–1
7–1
7–1
7–1
7–1
7–2
7–2
7–3
7–3
7–3
7–4
7–4
7–4
7–4
7–4
7–6
8–1
8–1
8.2
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3
Static Digital Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4
ADC Digital Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.5
Analog-to-Digital Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.6
Input Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.7
DAC Interpolation Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.8
Digital-to-Analog Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.9
DAC Output Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.10 I2C Serial Port Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . .
9 System Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 Mechanical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A Software Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.1
Main Control Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.1.1
Main Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.1.2
Main Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.1.3
Analog Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.2
Volume Gain Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.3
Treble Control Register Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.4
Bass Control Register Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.5
I2C Mix Register Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.6
Programming Instruction for the Loudness Contour . . . . . . . . . . . . . .
A.7
Examples of DRCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.7.1
DRCE On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.7.2
Above Threshold Ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.7.3
Below Threshold Ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.7.4
Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.7.5
Time Constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.7.6
DRCE Example With Threshold at –12 dB . . . . . . . . . . . . .
8–1
8–1
8–2
8–3
8–4
8–4
8–5
8–5
8–6
9–1
10–1
A–1
A–3
A–3
A–3
A–4
A–5
A–6
A–7
A–7
A–9
A–9
A–9
A–10
A–11
A–12
A–12
A–13
v
List of Illustrations
Figure
1–1
1–2
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
2–10
3–1
3–2
3–3
3–4
4–1
4–2
4–3
4–4
5–1
6–1
7–1
7–2
7–3
8–1
8–2
8–3
8–4
8–5
vi
Title
Page
TAS3004 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
TAS3004 Terminal Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
MSB First, Right-Justified Serial Interface Format—Normal Mode . . . . . 2–2
I2S Serial Interface Format—Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
MSB Left-Justified Serial Interface Format—Normal Mode . . . . . . . . . . . 2–4
MSB First, Right-Justified Serial Interface Format—Monaural ADC Mode,
B Left Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
I2S Serial Interface Format—Monaural ADC Mode,
B Left Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
MSB Left-Justified Serial Interface Format—Monaural ADC Mode,
B Left Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
MSB First, Right-Justified Serial Interface Format—Monaural ADC
Mode, B Right Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
I2S Serial Interface Format—Monaural ADC Mode,
B Right Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
MSB Left-Justified Serial Interface Format—Monaural ADC Mode,
B Right Input Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
For Right-/Left-Justified, I2S, and Left-/Left-Justified Serial Protocols . . 2–11
Analog Input to the TAS3004 Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
VCOM Decoupling Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Analog Output With External Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
TAS3004 Reference Voltage Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3
TAS3004 Mix Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
De-Emphasis Mode Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . 4–3
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
TAS3004 Digital Signal Processing Block Diagram . . . . . . . . . . . . . . . . . . 4–6
Biquad Cascade Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Typical I2C Data Transfer Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
TAS3004 Reset Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–2
Power-Down Timing Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–3
Internal Interface Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–5
ADC Digital Filter Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–2
ADC Digital Filter Stopband Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 8–2
ADC Digital Filter Passband Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 8–3
ADC High Pass Filter Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–3
DAC Filter Overall Frequency Characteristics . . . . . . . . . . . . . . . . . . . . . . . 8–4
8–6
8–7
9–1
9–2
A–1
A–2
DAC Digital Filter Passband Ripple Characteristics . . . . . . . . . . . . . . . . . . 8–4
I2C Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–6
Stereo Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–1
TAS3004 Device, 2.1 Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–2
TAS3004 DRCE Characteristics in the dB Domain . . . . . . . . . . . . . . . . . . A–10
DRCE Example With Threshold at –12 dB . . . . . . . . . . . . . . . . . . . . . . . . . A–13
vii
List of Tables
Table
1–1
2–1
4–1
4–2
6–1
6–2
6–3
7–1
7–2
7–3
7–4
7–5
A–1
A–2
A–3
A–4
A–5
A–6
A–7
A–8
A–9
A–10
A–11
A–12
A–13
A–14
A–15
A–16
viii
Title
TAS3004 Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Interface Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Control Register 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Protocol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Address Byte Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPI Terminal Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
512-Byte EEPROM Memory Map 2.0 Channels . . . . . . . . . . . . . . . . . . . .
512-Byte EEPROM Memory Map 2.1 Channels (with TAS3001) . . . . .
2048-Byte EEPROM Memory Map—2.0 Speakers With
Multiple Equalizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2048-Byte EEPROM Memory Map—2.1 Speakers With
Multiple Equalizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Control Register 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Control Register 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Control Register 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volume Versus Gain Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Treble Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bass Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mixer1 and Mixer2 Gain Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example of a DRCE I2C Instruction With DRCE On . . . . . . . . . . . . . . . .
Example of a DRCE I2C Instruction With DRCE Off . . . . . . . . . . . . . . . .
Above Threshold Ratios for Compression . . . . . . . . . . . . . . . . . . . . . . . . .
Above Threshold Ratios for Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . .
Below Threshold Ratios for Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Below Threshold Ratios for Compression . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time Constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
1–4
2–1
4–4
4–7
6–2
6–2
6–4
7–4
7–6
7–7
7–8
7–9
A–1
A–3
A–4
A–4
A–5
A–6
A–7
A–8
A–9
A–9
A–10
A–11
A–11
A–11
A–12
A–13
1 Introduction
1.1 Description
The TAS3004 device is a system-on-a-chip that replaces conventional analog equalization to perform digital
parametric equalization, dynamic range compression, and loudness contour. Additionally, this device provides
high-quality, soft digital volume, bass, and treble control. All control parameters are uploaded through the I2C port
from an outside MCU through the I2C slave port or from an external EPROM through the I2C master port.
The TAS3004 device also has an integrated 24-bit stereo codec with two I2C-selectable, single-ended inputs per
channel.
The digital parametric equalization consists of seven cascaded, independent biquad filters per channel. Each biquad
filter has five 24-bit coefficients that can be configured into many different filter functions (such as bandpass, high
pass, and low pass).
The internal loudness contour algorithm can be controlled and programmed with an I2C command.
Dynamic range compression/expansion (DRCE) is programmable through the I2C port. The system designer can set
the threshold, energy estimation time constant, compression ratio, and attack and decay time constants.
The TAS3004 device supports 13 serial interface formats (I2S, left justified, right justified) with data word lengths of
16, 18, 20, or 24 bits. The sampling frequency (fS) may be set to 32 kHz, 44.1 kHz, or 48 kHz.
The TAS3004 device uses a system clock generated by the internal phase-locked loop (PLL). The reference clock
for the PLL is provided by an external master clock (MCLK) of 256fS or 512fS, or a 256fS crystal.
The TAS3004 device has six internally configurable general-purpose input (GPI) terminals that control volume, bass,
treble, and equalization. Each GPI terminal has a debounce algorithm that is programmed into the TAS3004 internal
microcontroller.
1.2 Features
•
Programmable seven-band parametric equalization
•
Programmable digital volume control
•
Programmable digital bass and treble control
•
Programmable dynamic range compression/expansion (DRCE)
•
Programmable loudness contour/dynamic bass control
•
Configurable serial port for audio data
•
Two input data channels that can be mixed with digital data from the analog-to-digital converter (ADC) of
the codec (analog input). These channels are controlled by I2C commands.
•
Three output data channels: Left and right data go through equalization; bass, treble, DRCE, and volume
to SDOUT1; SDOUT2 mixes left and right data. SDOUT2 operates as a center channel or subwoofer
channel. The output of the ADC is available for additional processing.
•
Capability to configure ADC output to one of two monaural data streams or one stereo data stream
•
Capability to digitally mix left and right input channels for a monaural output to facilitate subwoofer operation
•
Serial I2C master/slave port that allows:
–
Downloading of control data to the device externally from the EPROM or an I2C master
1–1
–
1–2
Controlling other I2C devices
•
Two I2C-selectable, single-ended analog input stereo channels
•
Equalization bypass mode
•
Single 3.3-V power supply
•
Powerdown without reloading the coefficients
•
Sampling rates: 32 kHz, 44.1 kHz, or 48 kHz
•
Master clock frequency, 256fS or 512fS
•
Can have crystal input to replace MCLK. Crystal input frequency is 256fS.
•
Six GPI terminals for volume, bass, treble up/down control, mute, and selection of equalization filters
DVSS
DVDD
AVSS
AVDD
VREFP
VRFILT
AVSS(REF)
VREFM
1.3 Functional Block Diagram
AINRP
AINRM
Voltage
Reference
RINA
RINB
Analog
Supplies
Digital
Supplies
Analog
Control
Register
AINRP
AINRM
Output
Format
Control
Logic
24-Bit
Stereo
ADC
AINLP
AINLM
SDOUT0
LINA
AINLP
LINB
AINLM
VCOM
ALLPASS
INPA
GPI4
GPI3
GPI2
AOUTL
Controller
GPI5
AOUTR
24-Bit
Stereo DAC
GPI1
GPI0
L+R
SDOUT2
CS1
SDA
SCL
I2C
Control
L+R
32-Bit Audio Signal
Processor
PLL
CAP_PLL
MCLKO
XTALI/
MCLK
XTALO
OSC/CLK
Select
CLKSEL
IFM/S
SDATA
Control
SCLK/O
TEST
LRCLK/O
RESET
32-Bit Audio Signal
Processor
R
L
SDIN1
SDIN2
PWR_DN
Control
SDOUT1
Figure 1–1. TAS3004 Block Diagram
1–3
1.4 Terminal Assignments
LINB
AINLP
AINLM
V REFM
V REFP
AINRM
AINRP
RINB
RINA
AOUTL
VCOM
AOUTR
PACKAGE
(TOP VIEW)
48 47 46 45 44 43 42 41 40 39 38 37
LINA
VRFILT
AVSS(REF)
AVSS
INPA
RESET
CS1
PWR_DN
TEST
CAP_PLL
CLKSEL
MCLKO
1
36
2
35
3
34
4
33
5
32
6
31
7
30
8
29
9
28
10
27
11
26
12
25
NC
AVDD
NC
GPI5
GPI4
GPI3
GPI2
GPI1
GPI0
ALLPASS
SDOUT1
SDOUT0
XTALI/MCLK
XTALO
SCL
SDA
DVDD
DVSS
LRCLK/O
SCLK/O
IFM/S
SDIN1
SDIN2
SDOUT2
13 14 15 16 17 18 19 20 21 22 23 24
Figure 1–2. TAS3004 Terminal Assignments
1.5 Terminal Functions
Table 1–1. TAS3004 Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
AINLM
46
I
ADC left channel analog input (anti-alias capacitor)
AINLP
47
I
ADC left channel analog input (anti-alias capacitor)
AINRM
43
I
ADC right channel analog input (anti-alias capacitor)
AINRP
42
I
ADC right channel analog input (anti-alias capacitor)
ALLPASS
27
I
Logic high bypasses equalization filters
AOUTL
39
O
Left channel analog output
AOUTR
37
O
Right channel analog output
AVDD
AVSS
35
I
Analog power supply (3.3 V)
4
I
Analog voltage ground
AVSS(REF)
CAP_PLL
3
I
Analog ground voltage reference
10
I
Loop filter for internal phase-locked loop (PLL)
CLKSEL
11
I
CS1
7
I
Logic low selects 256fS; logic high selects 512fS MCLK
I2C address bit A0; low = 68h, high = 6Ah
1–4
Table 1–1. TAS3004 Terminal Functions (Continued)
TERMINAL
NAME
NO.
I/O
DESCRIPTION
DVDD
17
I
Digital power supply (3.3 V)
DVSS
18
I
Digital ground
GPI0
GPI1
GPI2
GPI3
GPI4
GPI5
28
29
30
31
32
33
I
Switch input terminals
IFM/S
21
I
Digital audio I/O control (low = input; high = output)
INPA
5
O
Low when analog input A is selected (will sink 4 mA)
LINA
1
I
Left channel analog input 1
LINB
48
I
Left channel analog input 2
LRCLK/O
19
I/O
Left/right clock input/output (output when IFM/S is high)
MCLKO
12
O
MCLK output for slave devices
NC
34
NC
36
PWR_DN
8
I
Logic high places the TAS3004 device in power-down mode
RESET
6
I
Logic low resets the TAS3004 device to the initial state
RINA
40
I
Right channel analog input 1
RINB
41
I
SCL
15
I/O
Right channel analog input 2
I2C clock connection
SCLK/O
20
I/O
SDA
16
I/O
SDIN1
22
I
Serial data input 1
SDIN2
23
I
Serial data input 2
SDOUT1
26
O
Serial data output (from internal audio processing)
SDOUT2
24
O
Serial data output (a monaural mix of left and right, before processing)
SDOUT0
25
O
Serial data output from ADC
No connection; Can be used as a printed circuit board routing channel
No connection; Can be used as a printed circuit board routing channel
Shift (bit) clock input (output when IFM/S is high)
I2C data connection
TEST
9
I
Reserved manufacturing test terminal; connect to DVSS
VCOM
38
O
Digital-to-analog converter mid-rail supply (decouple with parallel combination of 10-µF and 0.1-µF
capacitors)
VREFM
VREFP
45
I
ADC minus voltage reference
44
I
ADC plus voltage reference
VRFILT
XTALI/MCLK
2
O
Voltage reference low pass filter
13
I
Crystal or external MCLK input
XTALO
14
I
Crystal input (crystal is connected between terminals 13 and 14)
1–5
1–6
2 Audio Data Formats
2.1 Serial Interface Formats
The TAS3004 device works in master or slave mode.
In the master mode, terminal 21 (IFM/S) is tied high. This activates the master clock (MCLK) circuitry. A crystal can
be connected across terminals 13 (XTALI/MCLK) and 14 (XTALO), or an external, TTL-compatible MCLK can be
connected to XTALI/MCLK. In that case, MCLK outputs from terminal 12 (MCLKO) with terminals 19 (LRCLK/O) and
20 (SCLK/O) becoming outputs to drive slave devices.
In the slave mode, IFM/S is tied low. LRCLK/O and SCLK/O are inputs and the interface operates as a slave device
requiring externally supplied MCLK, LRCLK (left/right clock), and SCLK (shift clock) inputs. There are two options
for selecting the clock rates. If the 512fS MCLK rate is selected, terminal 11 (CLKSEL) is tied high and an MCLK rate
of 512fS must be supplied. If the 256fS MCLK is selected, CLKSEL is tied low and an MCLK of 256fS must be supplied.
In both cases, an LRCLK of 64SCLK must be supplied.
•
MCLK and SCLK must be synchronous and their edges must be at least 3 ns apart.
•
If the LRCLK phase changes more than 10MCLK, the codec automatically resets.
The TAS3004 device is compatible with 13 different serial interfaces. Available interface options are I2S, right justified,
and left justified. Table 2–1 indicates how the 13 options are selected using the I2C bus and the main control register
(MCR, I2C address x01h). All serial interface options at either 16, 18, 20, or 24 bits operate with SCLK at 64fS.
Additionally, the 16-bit mode operates at 32fS.
Table 2–1. Serial Interface Options
SERIAL INTERFACE
SDIN1, SDIN2, SDOUT1, SDOUT2, AND SDOUT0
MODE
MCR BIT (6)
MCR BIT (5–4)
MCR BIT (1–0)
0
0
00
00
16-bit, left justified, 32fS
1
1
00
00
16-bit, left justified, 64fS
2
1
01
00
3
1
10
00
16-bit, right justified, 64fS
16-bit, I2S, 64fS
4
1
00
01
18-bit, left justified, 64fS
5
1
01
01
6
1
10
01
18-bit, right justified, 64fS
18-bit, I2S, 64fS
7
1
00
10
20-bit, left justified, 64fS
8
1
01
10
9
1
10
10
20-bit, right justified, 64fS
20-bit, I2S, 64fS
10
1
00
11
24-bit, left justified, 64fS
11
1
01
11
12
1
10
11
24-bit, right justified, 64fS
24-bit, I2S, 64fS
Figure 2–1 through Figure 2–9 illustrate the relationship between the SCLK, LRCLK, and the serial data I/O for the
different interface protocols.
2–1
2.2 ADC Digital Output Modes
ADC digital output mode (SDOUT0) has two operational modes, normal and monaural. In the normal mode, the
output of the ADC conforms to the output modes described in Sections 2.2.1 through 2.2.3. To enter the normal output
mode, bit 7 (ADM) in the analog control register must be cleared to 0. In the monaural output mode, the digital output
of the ADC conforms to the output modes described in Sections 2.3.1 through 2.3.6. To enter the monaural mode,
bit 7 (ADM) in the analog control register must be set to 1.
2.2.1
MSB First, Right-Justified Serial Interface Format—Normal Mode
The normal output mode for the MSB first, right-justified serial interface format is for 16, 18, 20, and 24 bits with bit 7
(ADM) in the analog control register cleared to 0. Figure 2–1 shows the following characteristics of this protocol:
•
Left channel is transmitted when LRCLK is high.
•
The SDIN(s) (recorded) data is justified to the trailing edge of the LRCLK.
•
The SDOUT(s) MSB (playback) data is transmitted at the same time as LRCLK edge and captured at the
next rising edge of SCLK.
•
If LRCLK phase changes by more than 10MCLK, the codec automatically resets.
SCLK
LRCLK = fS
SDIN
……
MSB
……
LSB
……
MSB
……
LSB
SDOUT
……
MSB
……
LSB
……
MSB
……
LSB
Left Channel
Right Channel
Figure 2–1. MSB First, Right-Justified Serial Interface Format—Normal Mode
2–2
2.2.2
I2S Serial Interface Format—Normal Mode
The normal output mode for the I2S serial interface format is for 16, 18, 20, and 24 bits with bit 7 (ADM) in the analog
control register cleared to 0.
Figure 2–2 shows the following characteristics of this protocol:
•
Left channel is transmitted when LRCLK is low.
•
SDIN is sampled with the rising edge of SCLK.
•
SDOUT is transmitted on the falling edge of SCLK.
•
If LRCLK phase changes by more than 10MCLK, the codec automatically resets.
SCLK
LRCLK = fS
SDIN
X
MSB
……
LSB
…
X
MSB
……
LSB
…
SDOUT
X
MSB
……
LSB
…
X
MSB
……
LSB
…
Left Channel
Right Channel
Figure 2–2. I2S Serial Interface Format—Normal Mode
2–3
2.2.3
MSB Left-Justified Serial Interface Format—Normal Mode
The normal output mode for the MSB left-justified serial interface format is for 16, 18, 20, and 24 bits with bit 7 (ADM)
in the analog control register cleared to 0.
Figure 2–3 shows the following characteristics of this protocol:
•
Left channel is transmitted when LRCLK is high.
•
The SDIN data is justified to the leading edge of the LRCLK.
•
The MSBs are transmitted at the same time as LRCLK edge and captured at the next rising edge of SCLK.
SCLK
LRCLK = fS
SDIN
MSB
……
LSB
……
MSB
……
LSB
……
SDOUT
MSB
……
LSB
……
MSB
……
LSB
……
Left Channel
Right Channel
Figure 2–3. MSB Left-Justified Serial Interface Format—Normal Mode
2.3 ADC Digital Output Mode—Monaural
For the monaural ADC digital output mode, bit 7 (ADM) is set to 1, and bit 6 (LRB) and bit 1 (INP) in the analog control
register (see Section 4.8, Analog Control Register Operation) control the operation of the monaural output mode. All
interface formats are for 16, 18, 20, and 24 bits.
2–4
2.3.1 MSB First, Right-Justified Serial Interface Format—Monaural ADC Mode, B Left Input
Selected
The monaural output mode for the MSB first, right-justified serial interface format is for 16, 18, 20, and 24 bits with
the following bits in the analog control register set as shown:
•
Bit 7 (ADM) is set to 1.
•
Bit 6 (LRB) is cleared to 0.
•
Bit 1 (INP) is set to 1.
Figure 2–4 shows the following characteristics of this protocol:
•
Left channel is transmitted when LRCLK is either high or low.
•
The SDIN(s) (recorded) data is justified to the trailing edge of the LRCLK.
•
The SDOUT(s) MSB (playback) data is transmitted at the same time as LRCLK edge and captured at the
next rising edge of SCLK.
•
If LRCLK phase changes by more than 10MCLK, the codec automatically resets.
SCLK
LRCLK = fS
SDIN
……
MSB
……
LSB
……
MSB
……
LSB
SDOUT0
……
MSB
……
LSB
……
MSB
……
LSB
Left Channel
Left Channel
Figure 2–4. MSB First, Right-Justified Serial Interface Format—Monaural ADC Mode, B Left Input
Selected
2–5
2.3.2
I2S Serial Interface Format—Monaural ADC Mode, B Left Input Selected
The monaural output mode for the I2S serial interface format is for 16, 18, 20, and 24 bits with the following bits in
the analog control register set as shown:
•
Bit 7 (ADM) is set to 1.
•
Bit 6 (LRB) is cleared to 0.
•
Bit 1 (INP) is set to 1.
Figure 2–5 shows the following characteristics of this protocol:
•
Left channel is transmitted when LRCLK is either high or low.
•
SDIN is sampled with the rising edge of SCLK.
•
SDOUT is transmitted on the falling edge of SCLK.
•
If LRCLK phase changes by more than 10MCLK, the codec automatically resets.
SCLK
LRCLK = fS
SDIN
X
MSB
……
LSB
…
X
MSB
……
LSB
…
SDOUT0
X
MSB
……
LSB
…
X
MSB
……
LSB
…
Left Channel
Left Channel
Figure 2–5. I2S Serial Interface Format—Monaural ADC Mode, B Left Input Selected
2–6
2.3.3
MSB Left-Justified Serial Interface Format—Monaural ADC Mode, B Left Input Selected
The monaural output mode for the MSB left-justified serial interface format is for 16, 18, 20, and 24 bits with the
following bits in the analog control register set as shown:
•
Bit 7 (ADM) is set to 1.
•
Bit 6 (LRB) is cleared to 0.
•
Bit 1 (INP) is set to 1.
Figure 2–6 shows the following characteristics of this protocol:
•
Left channel is transmitted when LRCLK is either high or low.
•
The SDIN data is justified to the leading edge of the LRCLK.
•
The MSBs are transmitted at the same time as LRCLK edge and captured at the next rising edge of SCLK.
SCLK
LRCLK = fS
SDIN
MSB
……
LSB
……
MSB
……
LSB
……
SDOUT0
MSB
……
LSB
……
MSB
……
LSB
……
Left Channel
Left Channel
Figure 2–6. MSB Left-Justified Serial Interface Format—Monaural ADC Mode, B Left Input Selected
2–7
2.3.4 MSB First, Right-Justified Serial Interface Format—Monaural ADC Mode, B Right Input
Selected
The monaural output mode for the MSB first, right-justified serial interface format is for 16, 18, 20, and 24 bits with
the following bits in the analog control register set as shown:
•
Bit 7 (ADM) is set to 1.
•
Bit 6 (LRB) is set to 1.
•
Bit 1 (INP) is set to 1.
Figure 2–7 shows the following characteristics of this protocol:
•
Right channel is transmitted when LRCLK is either high or low.
•
The SDIN(s) (recorded) data is justified to the trailing edge of the LRCLK.
•
The SDOUT(s) MSB (playback) data is transmitted at the same time as LRCLK edge and captured at the
next rising edge of SCLK.
•
If LRCLK phase changes by more than 10MCLK, the codec automatically resets.
SCLK
LRCLK = fS
SDIN
……
MSB
……
LSB
……
MSB
……
LSB
SDOUT0
……
MSB
……
LSB
……
MSB
……
LSB
Right Channel
Right Channel
Figure 2–7. MSB First, Right-Justified Serial Interface Format—Monaural ADC Mode, B Right Input
Selected
2–8
2.3.5
I2S Serial Interface Format—Monaural ADC Mode, B Right Input Selected
The monaural output mode for the I2S serial interface format is for 16, 18, 20, and 24 bits with the following bits in
the analog control register set as shown:
•
Bit 7 (ADM) is set to 1.
•
Bit 6 (LRB) is set to 1.
•
Bit 1 (INP) is set to 1.
Figure 2–8 shows the following characteristics of this protocol:
•
Right channel is transmitted when LRCLK is either high or low.
•
SDIN is sampled with the rising edge of SCLK.
•
SDOUT is transmitted on the falling edge of SCLK.
•
If LRCLK phase changes by more than 10MCLK, the codec automatically resets.
SCLK
LRCLK = fS
SDIN
X
MSB
……
LSB
…
X
MSB
……
LSB
…
SDOUT0
X
MSB
……
LSB
…
X
MSB
……
LSB
…
Right Channel
Right Channel
Figure 2–8. I2S Serial Interface Format—Monaural ADC Mode, B Right Input Selected
2–9
2.3.6
MSB Left-Justified Serial Interface Format—Monaural ADC Mode, B Right Input Selected
The monaural output mode for the MSB left-justified serial interface format is for 16, 18, 20, and 24 bits with the
following bits in the analog control register set as shown:
•
Bit 7 (ADM) is set to 1.
•
Bit 6 (LRB) is set to 1.
•
Bit 1 (INP) is set to 1.
Figure 2–9 shows the following characteristics of this protocol:
•
Right channel is transmitted when LRCLK is either high or low.
•
The SDIN data is justified to the leading edge of the LRCLK.
•
The MSBs are transmitted at the same time as LRCLK edge and captured at the next rising edge of SCLK.
SCLK
LRCLK = fS
SDIN
MSB
……
LSB
……
MSB
……
LSB
……
SDOUT0
MSB
……
LSB
……
MSB
……
LSB
……
Right Channel
Right Channel
Figure 2–9. MSB Left-Justified Serial Interface Format—Monaural ADC Mode, B Right Input Selected
2–10
2.4 Switching Characteristics
PARAMETER
tc(SCLK)
td(SLR)
SCLK frequency
td(SDOUT)
tsu(SDIN)
SDOUT valid from SCLK falling (see Note 1)
th(SDIN)
LRCLK
SDIN hold after SCLK rising edge
MIN
SCLK rising to LRCLK edge
TYP
MAX
UNIT
3.072
MHz
20
ns
(1/256fS) + 10
SDIN setup before SCLK rising edge
20
ns
100
32
Duty cycle
ns
ns
44.1
48
50
kHz
%
NOTE 1: Maximum of 50-pF external load on SDOUT.
tc(SCLK)
tr(SCLK)
SCLK
tf(SCLK)
td(SLR)
LRCLK
td(SDOUT)
td(SLR)
SDOUT1
SDOUT2
SDOUT0
tsu(SDIN)
th(SDIN)
SDIN1
SDIN2
Figure 2–10. For Right-/Left-Justified, I2S, and Left-/Left-Justified Serial Protocols
2–11
2–12
3 Analog Input/Output
The TAS3004 device contains a stereo 24-bit ADC with two single-ended inputs per channel. Selection of the A or
B analog input is accomplished by setting a bit in the analog control register (ACR) by an I2C command. Additionally,
the TAS3004 device has a stereo 24-bit digital-to-analog converter (DAC).
3.1 Analog Input
Figure 3–1 shows the technique and components required for analog input to the TAS3004 device. The maximum
input signal must not exceed 0.7 Vrms. Selection of the above component values gives a frequency response from
20 Hz to 20 kHz at a sampling frequency of 48 kHz without alias frequency problems.
2
1200 pF
AINRP
AINRM
0.47 µF
RINA
1
Voltage
Reference
RINB
1
0.47 µF
AINRP
2
1200 pF
AINRM
AINLP
24-Bit
Stereo
ADC
AINLM
0.47 µF
LINA
1
LINB
1
AINLP
0.47 µF
AINLM
1
Analog Inputs – Use 0.47 µF for 20-Hz Cutoff
2
Anti-Alias Capacitors for fS = 48 kHz
3
Tie unused analog inputs to analog ground through 0.1-µF capacitors.
Input Select Command
From Internal Controller
Figure 3–1. Analog Input to the TAS3004 Device
3.2 Analog Output
3.2.1
Analog Output
The full scale analog output from the TAS3004 device is 0.7 Vrms. It is referenced to VCOM which is approximately
1.5 Vdc. VCOM must be decoupled with the network as shown in Figure 3–2.
3–1
Analog Output
(Adjust Capacitors for Desired
Low Frequency Response)
AOUTR
24-Bit
DAC
VCOM
+
10 µF
AOUTL
0.1 µF
AGND
Figure 3–2. VCOM Decoupling Network
3.2.2
Analog Output With Gain
Since the analog output from the TAS3004 device is 0.7 Vrms, the output level can be increased by using an external
amplifier. The circuit shown in Figure 3–3 boosts the output level to 1 Vrms (when it has a gain of 1.414) and provides
improved signal-to-noise ratio (SNR). Since this circuit lowers the noise floor, THD + N is improved also.
C4
Analog Output
(Adjust Capacitors for Desired
Low Frequency Response)
AOUTR
–
C1
+
24-Bit
DAC
10 µF
AOUTL
TLV2362
or Equilvalent
C3
VCOM
+
0.1 µF
+5 Op Amp/2
C5
AGND
C2
C1 = C2 = C3
C4 = C5
–
+
TLV2362
or Equilvalent
+5 Op Amp/2
Figure 3–3. Analog Output With External Amplifier
3–2
3.2.3
Reference Voltage Filter
Figure 3–4 shows the TAS3004 reference voltage filter.
0.1 µF
4
3
2
45
VREFM
0.1 µF
VRFILT
0.1 µF
AVSS(REF)
1 µF
+
AVSS
15 µF
+
VREFP
44
TAS3004
Figure 3–4. TAS3004 Reference Voltage Filter
3–3
3–4
4 Audio Control/Enhancement Functions
4.1 Soft Volume Update
The TAS3004 device implements a TI proprietary soft volume update. This feature allows a smooth and
pleasant-sounding change from one volume level to another over the entire range of volume control (18 dB to mute).
The volume is adjustable by downloading a 4.16 gain coefficient through the I2C interface. Table A–5 lists the 4.16
coefficients converted into dB for the range of –70 dB to 18 dB with 0.5-dB step resolution.
Right and left channel volumes can be unganged and set to different values. This feature implements a balance
control.
Volume is changed by writing the desired value into the volume control registers. This is done by asserting the GPI
terminals for volume-up or volume-down for a limited range of volume control. Alternately, volume control settings
can be sent to the TAS3004 device over the I2C bus.
4.2 Software Soft Mute
Mute is implemented by loading all zeros in the volume control register. This causes the volume to ramp down over
a duration of 2048fS samples to a final output of 0 (– infinity dB).
Soft mute can be enabled by either asserting the mute GPI terminal or sending a mute command over the I2C bus.
4.3 Input Mixer Control
The TAS3004 device is capable of mixing and multiplexing three channels of serial audio data. The mixing is
controlled through three mixer control registers. This is accomplished by loading values into the corresponding bytes
of the mixer left gain (07h) and mixer right gain (08h) control registers.
The values loaded into these registers are in 4.20 format—4 bits for the integer and 20 bits for the fractional part.
Table A–8 lists the 4.20 numbers converted into dB for the range of –70 dB to 18 dB, although any positive 4.20
number may be used.
To mute any of the channels, 0s are loaded into the respective mixer control register.
Mixer controls are updated instantly and can cause audible artifacts for large changes in setting when updated
dynamically outside of the fast load mode; therefore, it is desirable to use fast load in conjunction with the soft-volume
mode.
SDIN1, SDIN2, and the ADC output can be mixed with a user-selectable gain for each channel. The gain control
registers are represented in 4.20 format.
4–1
Left Channel Mix Coefficients
I2C Register Address 08h
SDIN1 ^ SDIN2 ^ ADC
= (3) 24-Bit Left Mix Coefficient
SDIN1_L
SDIN2_L
L_SUM
7 Biquad
Filters
Tone
Soft
Volume
DRCE
ADC_L
SDOUT1
SDIN1_R
SDIN2_R
7 Biquad
Filters
Tone
Soft
Volume
DRCE
ADC_R
R_SUM
1/2
L + R_SUM
SDOUT2
1/2
Right Channel Mix Coefficients
I2C Register Address 07h
SDIN1 ^ SDIN2 ^ ADC
= (3) 24-Bit Right Mix Coefficient
Figure 4–1. TAS3004 Mix Function
4.4 Mono Mixer Control
The TAS3004 device contains a second mixer that performs the function of mixing left and right channel digital audio
data from the input mixer in order to derive a monaural channel. This mixer has a fixed gain of –6 dB so that full scale
inputs on L_sum and R_sum do not produce clipping on the resulting L+R_sum.
The output of this mixer is present on terminal 24 (SDOUT2) and is generally used for a digitally-mixed subwoofer
or center channel application.
4.5 Treble Control
The treble gain level may be adjusted within the range of 15 dB to –15 dB with 0.5-dB step resolution. The level
changes are accomplished by downloading treble codes (shown in Appendix A) into the treble gain register.
Alternately, a limited range of treble control is available by asserting the GPI terminals.
The treble control has a corner frequency of 6 kHz at a 48-kHz sample rate.
The gain values for treble control can be found in Section A.3.
4–2
4.6 Bass Control
The bass gain level can be adjusted within the range of 15 dB to –15 dB with 0.5-dB step resolution. The level changes
are accomplished by downloading bass codes (shown in Appendix A) into the bass frequency control register.
Alternately, a limited range of bass control is available by asserting the GPI terminals.
Bass control is a shelf filter with a corner frequency of 250 Hz at a 48-kHz sample rate.
The gain values for bass control can be found in Section A.4.
4.7 De-Emphasis (DM)
De-emphasis is implemented in the DAC and is software controlled. De-emphasis is valid at 44.1 kHz and 48 kHz.
To enable de-emphasis, values are written into the analog control register via the I2C command. See Section 4.8 for
analog control register operation.
Figure 4–2 illustrates the frequency response of the de-emphasis mode.
De-Emphasis
Response (dB)
3.18
(50 µs)
10.6
(15 µs)
Frequency (kHz)
Figure 4–2. De-Emphasis Mode Frequency Response
4–3
4.8 Analog Control Register Operation
The analog control register (ACR) allows control of de-emphasis, selection of the analog input channel to the ADC,
and analog power down.
An I2C master is required to write the appropriate command into the ACR. The ACR subaddress is 0x40.
Bit
Type
Default
7
6
5
4
3
2
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Table 4–1. Analog Control Register Description
BIT
FIELD NAME
TYPE
7
ADM
R/W
DESCRIPTION
ADC output mode.
0 = Normal operation
1 = A inputs are normal; B inputs are monaural.
6
LRB
R/W
Selects left or right B input for monaural output.
0 = B left input selected for monaural ADC output when bit 7 (ADM) is set to 1.
1 = B right input selected for monaural ADC output when bit 7 (ADM) is set to 1.
5–4
RSVD
R/W
Reserved. Bits 5 and 4 return 0s when read.
3–2
DM(1–0)
R/W
De-emphasis control.
00 = De-emphasis off (initial condition after reset)
01 = 48 kHz sample rate de-emphasis selected
10 = 44.1 kHz sample rate de-emphasis selected
11 = Reserved
1
INP
R/W
Analog input select.
0 = LINA and RINA selected (initial condition after reset)
1 = LINB and RINB selected
0
APD
R/W
Analog powerdown.
0 = Normal operation (initial condition after reset)
1 = Powerdown
4–4
4.9 Dynamic Loudness Contour
The necessity for applying loudness compensation to playback systems to compensate for the fact that the ear
perceives bass and treble less audibly at low levels than at high ones has been established with the first data
published by Fletcher and Munson in 1933.
There are many equal-loudness contours in publication, like Steven’s contours, Robinson and Dadson contours even
reached the acceptance level of ISO recommendation.
The TAS3004 device has a simplified loudness contour algorithm that diminishes the effect of weak bass at low
listening levels. Since contour has volume level dependency, the user must define the relation between the gain of
the contour circuit and the volume level.
Figure 4–3 is a block diagram of this circuit.
Volume
Biquad
Gain
Figure 4–3. Block Diagram
The loudness contour is activated by sending an activation command via I2C from an external device. Optionally, a
contour gain command can be sent by an external device to provide tracking with the system’s volume control.
4.9.1
Loudness Biquads
Loudness biquad filters for the left and right channels are independently programmable via I2C. Their subaddresses
are 0x21 and 0x22, respectively. The digital filters are written as five 24-bit (4.20) hex coefficients for each channel.
4.9.2
Loudness Gain
Loudness gain values for the left and right channels are independently programmable via I2C. Their subaddresses
are 0x23 and 0x24, respectively. The gain values are written as one 4.20 hex coefficient for each channel.
4.9.3
Loudness Contour Operation
When the frequency of the loudness contour is determined, a digital filter must be developed. Then, the gain of the
filter is determined. These values are placed in the storage area of the system controller (microcontroller) and sent
to the TAS3004 device when it is desired to activate the loudness contour.
If it is necessary to change the frequency or gain of the contour, new gain and filter coefficients are sent by the system
controller. This function is performed normally when the volume control is changed (that is, more volume, less
contour). The gain of the loudness contour filter then tracks the volume control.
The loudness contour biquad filters are provided in addition to the seven equalization biquad filters.
See Section A.6 for programming instructions.
4–5
4.10 Dynamic Range Compression/Expansion
The TAS3004 device provides the user with the ability to manage the dynamic range of the audio system. The DRCE
receives data, and affects scaling after the volume/loudness block. As shown in Figure 4–4, the DRCE is applied after
the volume/loudness control block as a DRCE scale factor. The DRCE must be adjusted such that the signal does
not reach the hard limit value. However, if the signal does reach the maximum digital value, the saturation logic serves
as a hard limiter that does not allow the signal to extend beyond the available range.
Loudness
(Parametric
Equalization)
(Left Channel Mixer)
SDIN1_L
LEFT_SUM
SDIN2_L
(7)
2nd Order
IIR Filters
(Tone)
Bass/
Treble
(DRCE Scaling)
Soft
Volume/
Saturation
Logic
LEFT_OUT
Saturation
Logic
RIGHT_OUT
ANALOGIN_L
Dynamic
Range
Control
(Analog in From ADC)
ANALOGIN_R
SDIN1_R
RIGHT_SUM
SDIN2_R
(Right Channel Mixer)
(7)
2nd Order
IIR Filters
(Parametric
Equalization)
Bass/
Treble
Soft
Volume/
(DRCE Scaling)
(Tone)
Loudness
Figure 4–4. TAS3004 Digital Signal Processing Block Diagram
The DRCE instruction consists of eight bytes that must be sent each time in the order shown in the example code
of Table A–9. Each instruction downloaded must be eight bytes. If only one byte is changed, all eight bytes must be
transmitted. The first two bytes remain the same for every instruction, however the last six bytes can be programmed
using hexadecimal values from the corresponding tables referred to in Section A.7.
With high compression ratios and fast attack times available, this function is suited for a commercial killer in a
television set application.
4.11 AllPass Function
This function is enabled by setting terminal 27 (ALLPASS) on the TAS3004 device to 1. When asserted, the internal
equalization filters are set into AllPass (flat) mode. When this terminal is reset to 0, the equalization filters are returned
to the equalization that was in use before the terminal was asserted.
In AllPass mode, the bass and treble controls are still functional.
This function is frequently used for headphones. When the headphone plug is inserted into its jack, a switched contact
in the jack enables the AllPass function.
The AllPass function also can be activated by writing a 1 to bit 2 of the analog control register.
4–6
4.12 Main Control Register 2 (43h)
The TAS3004 device contains two main control registers: main control register 1 (MCR1) and main control register 2
(MCR2). The MCR2 contains the bits associated with the AllPass function and the download of bass and treble control
information, and it is accessed via I2C with the address 43h.
MCR2 (43h)
Bit
Type
Default
b7
b6
b5
b4
b3
b2
b1
b0
R/W
R
R
R
R
R
R/W
R
0
0
0
x
x
x
0
0
Table 4–2. Main Control Register 2 Description
BIT
TYPE
b7
R/W
DESCRIPTION
b6–b5
R
Reserved. Bits b6 and b5 return 0s when read.
b4–b2
R
Undefined.
b1
R/W
b0
R
0 = Normal operation (initial condition after reset)
1 = Download bass and treble
0 = Normal operation (initial condition after reset)
1 = AllPass mode (bass and treble are still functional)
Reserved. Bit b0 returns 0 when read.
4–7
4–8
5 Filter Processor
5.1 Biquad Block
The biquad block consists of seven digital biquad filters per channel organized in a cascade structure, as shown in
Figure 5–1. Each of these biquad filters has five downloadable 24-bit (4.20) coefficients. Each stereo channel has
independent coefficients.
Biquad 1
Biquad 2 ...
Biquad N
Figure 5–1. Biquad Cascade Configuration
5.1.1
Filter Coefficients
The filter coefficients for the TAS3004 device are downloaded through the I2C port and loaded into the biquad memory
space. Each biquad filter memory space has an independent address. Digital audio data coming into the device is
processed by the biquad block and then converted into analog waveforms by the DAC. Alternately, filters can be
loaded by asserting terminals on the GPI port.
5.1.2
Biquad Structure
The biquad structure that is used for the parametric equalization filters is as follows:
b ) b 1z *1 ) b 2z *2
H(z) + 0
a 0 ) a 1z *1 ) a 2z *2
(1)
NOTE: a0 is fixed at value 1 and is not downloadable.
The coefficients for these filters are represented in 4.20 format—4 bits for the integer part and 20 bits for the fractional
part. In order to transmit them over I2C, it is necessary to separate each coefficient into three bytes. The upper 4 bits
of byte 2 is the integer part, and the second nibble of byte 2, byte 1, and byte 0 are the fractional parts.
The filters can be designed using the automatic loudspeaker equalization program (ALE) or a script running under
MatLab named Filtermaker. Both of these tools are available from Texas Instruments.
5–1
5–2
6 I2C Serial Control Interface
6.1 Introduction
Control parameters for the TAS3004 device can be loaded from an I2C serial EPROM by using the TAS3004 master
interface mode. If no EPROM is found, the TAS3004 device becomes a slave device and loads from another I2C
master interface. Information loaded into the TAS3004 registers is defined in Appendix A.
The I2C bus uses terminals 16 (SDA for data) and 15 (SCL for clock) to communicate between integrated circuits in
a system. These devices can be addressed by sending a unique 7-bit slave address plus R/W bit (1 byte). All
compatible devices share the same terminals via a bidirectional bus using a wired-AND connection. An external
pullup resistor must be used to set the high level on the bus. The TAS3004 device operates in standard mode up to
100 kbps with as many devices on the bus as desired up to the capacitance load limit of 400 pF.
Furthermore, the TAS3004 device supports a subset of the SMBus protocol. When it is attached to the SMBUS, then
byte, word, and block transfers are supported. The SMBus NAK function is not supported and care must be taken
with the sequence of the instructions sent to the TAS3004 device.
Additionally, the TAS3004 device operates in either master or slave mode; therefore, at least one device connected
to the I2C bus must operate in master mode.
6.2 I2C Protocol
The bus standard uses transitions on SDA while the clock is high to indicate start and stop conditions. A high-to-low
transition on SDA indicates a start and a low-to-high transition indicates a stop. Normal data bit transitions must occur
within the low time of the clock period. Figure 6–1 shows these conditions. These start and stop conditions for the
I2C bus are required by standard protocol to be generated by the master. The master must also generate the 7-bit
slave address and the read/write (R/W) bit to open communication with another device and then wait for an
acknowledge condition. The slave holds SDA low during acknowledge clock period to indicate an acknowledgment.
When this occurs, the master transmits the next byte of the sequence.
After each 8-bit word, an acknowledgment must be transmitted by the receiving device. There is no limit on the
number of bytes that can be transmitted between start and stop conditions. When the last word transfers, the master
generates a stop condition to release the bus. Figure 6–1 shows a generic data transfer sequence.
SDA
7-Bit
Slave Address
R/
W
7
0
6
1
A
8-Bit Register Data
for Address (N)
7
6
1
0
A
8-Bit Register Data
for Address (N)
7
6
1
A
0
8-Bit Register Data
for Address (N+1)
7
6
1
A
0
SCL
Start
Stop
Figure 6–1. Typical I2C Data Transfer Sequence
6–1
Table 6–1 lists the definitions used by the I2C protocol.
Table 6–1. I2C Protocol Definitions
DEFINITION
DESCRIPTION
Transmitter
The device that sends data
Receiver
The device that receives data
Master
The device that initiates a transfer, generates clock signals, and terminates the transfer
Slave
The device addressed by the master
Multimaster
More than one master can attempt to control the bus at the same time without corrupting the message.
Arbitration
Procedure to ensure the message is not corrupted when two masters attempt to control the bus.
Synchronization
Procedure to synchronize the clock signals of two or more devices
6.3 Operation
The 7-bit address for the TAS3004 device is 011010X R/W where X is a programmable address bit, set by terminal 7
(CS1). Combining CS1 and the R/W bit, the TAS3004 device can respond to four different I2C addresses (two read
and two write). These two addresses are licensed I2C addresses that do not conflict with other licensed I2C audio
devices. In addition to the 7-bit device address, subaddresses direct communication to the proper memory location
within the device. A complete table of subaddresses and control registers is provided in Appendix A. For example,
to change bass to 10-dB gain, Section 6.3.1 shows the data that is written to the I2C port:
Table 6–2. I2C Address Byte Table
6.3.1
Start
I2C ADDRESS BYTE
A6–A1
CS1 (A0)
R/W
0x68
011010
0
0
0x69
011010
0
1
0x6A
011010
1
0
0x6B
011010
1
1
Write Cycle Example
Slave Address
R/W
FUNCTION
A
Subaddress
A
Data
Start
DESCRIPTION
Start condition as defined in I2C
Slave address
0110100 (CS1 = 0)
R/W
0 (write)
A
Acknowledgement as defined in I2C (slave)
Subaddress
00000110 (see Appendix A)
Data
00011100 (see Appendix A)
Stop
Stop condition as defined in I2C
A
Stop
NOTE: Table is for serial data (SDA); serial clock (SCL) is not shown but conditions apply as well.
Whenever writing to a subaddress, the correct number of data bytes must follow in order to complete the write cycle.
For example, if the volume control register with subaddress 04 (hex) is written to, six bytes of data must follow;
otherwise, the cycle is incomplete and errors occur.
6–2
TAS3004 I2C Readback Example
6.3.2
The TAS3004 will save in a Stack or First-In First-Out (FIFO) buffer the last 7 bytes that were sent to it. When an I2C
read command is sent to the device (LSB=high), it answers by popping the first byte off the stack. The TAS3004 will
then expect either a SendAck command or an I2C Stop command from the host. If a SendAck command is sent from
the host then the TAS3004 will pop another byte off the stack. If an I2C Stop is sent then the TAS3004 will end this
transaction. The proper sequence for reading is described as follows:
I2C Start
Send I2C address byte with read Bit Set to 1 (LSB set equal to 1)
receive Byte 0
Send Ack
receive Byte 1
Send Ack
receive Byte 2
Send Ack
receive Byte 3
Send Ack
receive Byte 4
Send Ack
receive Byte 5
Send Ack
receive Byte 6 (if you send an ACK after Byte 6 it will lock up the TAS3004)
I2C Stop
Where:
•
I2C Start is a valid I2C Start Command
•
Receive Byte is a valid I2C Command which reads a byte from the TAS3004.
•
SendAck is a avalid I2C Command that informs the TAS3004 that a byte has been read.
•
I2C Stop is a valid I2C Stop Command
NOTES: 1. The TAS3004 will appear to be locked up, if a SendACK is issued after the last byte read. It is required to send an I2C Stop Condition
after the last byte and not a SendACK.
2. The I2Cstart and I2Cstop commands are the same for both I2C read and I2C write.
6.3.3
I2C Wait States
The TAS3004 device performs interpolation algorithms for its volume and tone controls. If a volume or tone change
is sent to the part via I2C, the command sent after the volume or tone (bass and treble) change causes an I2C wait
state to occur. This wait state lasts from 41 ms to 231 ms, depending on the system clock rate, the command sent,
and, in the case of bass or treble, the amount of the change.
Secondly, if a long series of commands are sent to the TAS3004 device, it may occasionally create a short wait state
on the order of 150 µs to 300 µs while it loads and processes the commands.
When a sample rate of 32 kHz is used, longer wait states can occur, occasionally up to 15 ms.
The preferred way to take care of wait states is to use an I2C controller that recognizes wait states. During the wait
state period, it stops sending data over I2C. If this function is not available on the system controller, fixed delays can
be implemented in the system software to ensure that the controller is not trying to send more data while the TAS3004
device is busy. Sending I2C data while the TAS3004 device is busy causes errors and locks up the device, which must
then be reset.
6–3
Table 6–3 gives typical values of the wait states that can be expected with the various functions of the part:
Table 6–3. I2C Wait States
SYSTEM SAMPLING FREQUENCY
Comment
32 kHz
44.1 kHz
48 kHz
Volume
62 ms
49 ms
41 ms
Not dependent on size of change
Bass
231 ms
167 ms
153 ms
0 to –18 dB, –1 dB = 0.055 T @ fS
Treble
231 ms
167 ms
153 ms
0 to –18 dB, –1 dB = 0.055 T @ fS
DRC On
300 µs
300 µs
300 µs
Mixer
None
None
None
Loudness
None
None
None
Equalization
15 ms
190 µs
300 µs
Can occur with each filter
6.4 SMBus Operation
The TAS3004 device supports a subset of the SMBus protocol. With proper programming techniques, it is possible
to use the SMBus to set up the TAS3004 device.
6.4.1
Block Write Protocol
The TAS3004 device supports the block write protocol that allows up to 32 bytes to be sent as a block. To send a
command using this format, the most significant bit (MSB) of the TAS3004 subaddress must be set high and the
subaddress (also with MSB set high) must be programmed into the SMBus command byte. This operation signals
the TAS3004 device to realize that the next byte is the SMBus byte count byte. The next byte after the byte count is
then entered into the device as the first byte of data.
SMBus
Command Byte
6.4.2
68h
8rh
xx
dd
dd
dd
TAS3004
Address
Subaddress
(r = subaddress)
Byte Count
(Don’t Care)
Data
Data
Data
Write Byte Protocol
The TAS3004 device also supports the SMBus write byte protocol. Writing to the main control register (MCR), bass,
and treble registers require using the byte write protocol. To send a command using this format, the most significant
bit (MSB) of the TAS3004 subaddress must be set high and the subaddress (also with MSB set high) must be
programmed into the SMBus command byte. The next byte after the command byte is then entered into the device
as the first byte of data.
SMBus
Command Byte
6–4
68h
8rh
dd
TAS3004
Address
Subaddress
(r = subaddress)
Data
6.4.3
Wait States
If separate I2C/SMBus commands are sent too frequently, the TAS3004 device can generate a bus wait state. This
happens when the device is busy while performing smoothing operations and changing volume, bass, and treble.
The wait occurs after the bus acknowledge on the first data byte and can exceed the maximum allowable time allowed
according to the SMBus specification (worst case 200 ms).
The following is a possible bus wait state scenario:
CODE
Start
68
84
06
01
00
00
01
00
00
Stop
Wait†
ACTUAL
Start
68
84
06
01
00
00
01
00
00
Stop
† If the master does not recognize bus waiting or if the master times out on a long wait, the master must not send consecutive I2C/SMBus commands
without a time interval of 200 ms between transactions.
6.4.4
TAS3004 SMBus Readback
The TAS3004 device supports a subset of SMBus readback. When an SMBus read command is sent to the device
(LSB = high), it answers with the subaddress and the last six bytes written.
SMBus
Command
Byte
Byte
Count
SENT
Start
69h
xxh
07h
Stop
RECEIVED
Start
07h
aah
ddh
ddh
ddh
ddh
ddh
ddh
Stop
Byte
Count
Where:
xxh
aah
ddh
= Command byte, it is a don’t care because the response contains only the subaddress and the
last six bytes of data written to the TAS3004 device
= The last subaddress accessed in the device
= Data bytes from the TAS3004 device
NOTE: Use read sequence defined in 6.3.2
6–5
6–6
7 Microcontroller Operation
The TAS3004 device contains an internal microcontroller programmed by Texas Instruments to perform
housekeeping and interface functions. Additionally, it handles I2C communication and general purpose input
functions.
7.1 General Description
The microcontroller uses a 256fS system clock and can access up to 8K bytes of memory. It interfaces with the digital
audio interface I2C master/slave for downloading data and coefficients. It also interfaces with two internal DSPs for
transferring coefficients and other information.
The TAS3004 coefficients are loaded through I2C in the master or slave mode. Standard audio processing functions
(volume, bass, and treble) can be controlled/activated through external switches connected to the six GPI terminals.
Upon reset, the internal microcontroller sets all coefficients and audio parameters to the default values. See
Section 7.2.2 for default values.
If the TAS3004 address is 68h (ADDR_SEL=0), it becomes the bus master device and attempts to load parameters
and coefficients from the external EPROM. If no EPROM is present, the TAS3004 device remains in its default
condition. If addresses other than 68h/69h are set, the TAS3004 device only operates as an I2C slave device.
If the microcontroller determines the TAS3004 device has an I2C address of 68h/69h and the EPROM is present, the
microcontroller downloads coefficients from the EPROM. Once the download is complete, it enables the serial audio
in the mode defined by an I2C write to the MCR to transfer data into and out of the device. Before reading the EPROM,
the serial audio port defaults to I2S mode.
The TAS3004 device allows the user to update volume, bass, and treble dynamically by an I2C slave command or
by a simple GPI switch input. The GPI can select volume up and down, bass/treble up and down, or digital
equalizations. Up to five different equalizations (that is, flat, jazz, rock, voice, etc.) can be stored in the external
EPROM. Also, DRCE, MCR1, MCR2, and loudness contour are enabled and disabled by I2C.
When the TAS3004 device operates in the I2C master mode, it echoes changes to all of its functions to other I2C
addresses that are defined in its external EPROM. If no addresses are defined, it does not echo.
7.2 Power-Up/Power-Down Reset
7.2.1
Power-Up Sequence
An active low on terminal 6 (RESET) while MCLK is running, resets the internal microcontroller and DSP(s). RESET
synchronizes internally and can be asserted asynchronously or with the simple RC circuit in Figure 7–1. On reset,
SCL and SDA go to a high-impedance state. If the I2C address is set to 68h, approximately 400 µs after RESET
returns to a 1, the device sends a one-byte query via I2C to look for an EPROM. If an EPROM is found, it becomes
an I2C master; otherwise, it becomes an I2C slave. When using address 68h in the slave mode, an external master
must wait until after the EPROM query or else bus contention and improper operation occurs.
I2C address x6Ah does not query the bus for an EPROM. The address for the EPROM is xA0h.
7.2.2
Reset
The TAS3004 device has an asynchronous reset terminal (RESET). This reset is synchronized with various clocks
used in this device to generate a synchronous internal reset. Upon reset, the TAS3004 device goes through the
following process:
•
Clears all the RAM memory content
7–1
•
Clears all the registers in the circuits
•
Purges the codec
•
Selects analog input A (RINA and LINA) and sets the input A active indicator (INPA) low.
•
Initializes the equalization parameters to AllPass filters
•
Sets the digital audio interface to I2S—18-bit mode
•
Sets the bass/treble to 0 dB
•
Sets the mixer gain to 0 dB SDIN1 and mutes both SDIN2 and analog-in
•
Sets the volume to –40 dB
•
Turns off all enhancement features (DRCE, etc.).
•
Reads the I2C address. If the address is 68h, the device reads its EPROM. It is possible to load the
user-defined bass/treble data and break points (optional). If there is no data, the device loads default
bass/treble delta and break points from ROM.
•
If the address is 6Ah, the device puts the I2C interface in slave mode and waits for input.
7.2.3
Reset Circuit
Since the TAS3004 device has an internal power-on reset (POR), in many cases, additional components are not
needed to reset the device. It resets internally at approximately 80% of VDD.
In the case where the system’s power supplies are slow in reaching their final voltage or where there is a difference
in the time the system power supplies take to become stable, the TAS3004 reset can be delayed by a simple RC
circuit.
DVDD
10 kΩ
TAS3004
6
RESET
0.1 µF
DVSS
Figure 7–1. TAS3004 Reset Circuit
The values for the above circuit can be calculated by the simple equation:
trd = 0.8RC + 400 µs
Where:
trd = The delay before the TAS3004 device comes out of reset
C = Value of the capacitance from RESET (pin 6) to DVSS
R = Value of the resistance from RESET (pin 6) to DVDD
The circuit described in Figure 7–1 delays the start-up of the TAS3004 device approximately 1.2 ms.
When it is necessary to control the reset of the TAS3004 device with an external device, such as a microcontroller,
RESET (pin 6) can be treated as a logic signal. It then brings the device out of reset when the voltage on RESET
reaches VDD/2.
7.2.4
Fast Load Mode
While in fast load mode, it is possible to update the parametric equalization without any audio processing delay. The
audio processor pauses while the RAM is updated in this mode. Bass and treble cannot download in this mode. Mixer1
and Mixer2 registers can download in this mode or normal mode (FL bit = 0).
7–2
Once the download is complete, the fast load bit must be cleared by writing a 0 into bit 7 of the main control register
(MCR). This puts the TAS3004 device into normal mode.
7.2.5
Codec Reset
During initialization, the output of the CODEC is disabled. Throughout reset and initialization, the output of the DAC
is muted to prevent extraneous noise being sent to the system output.
Data from the ADC and other internal processing is purged so that when reset/initialization is complete, only valid
inputs are sent to the system output.
7.3 Power-Down Mode
The TAS3004 device has an asynchronous power-down mode. In the power-down mode, the internal control
registers and equalization programming of the device are stored in the device.
To enter power-down mode:
•
Assert the power-down control signal (1)
•
Set the serial audio input clocks to 0
The TAS3004 device goes into power-down mode.
To exit the power-down mode:
•
Assert RESET (logic 0)
•
Restart the serial audio clocks
•
Wait for a delay of 1.0 ms (to allow the PLL to lock)
•
Negate the power-down control signal (logic 0)
•
Negate RESET (logic 1)
The device then returns to the state it was in before power down (resumes normal operation).
7.3.1
Power-Down Timing Sequence
PWR_DN
RESET
MCLK
SCLK
LRCLK
SDATA
Power-Down Mode
Normal Operation
1 ms
Figure 7–2. Power-Down Timing Sequence
In power-down mode, the TAS3004 device consumes typically less than 1 mA.
7–3
7.4 Test Mode
Terminal 9 (TEST) is tied low in normal operation. This function is reserved for factory test and must not be asserted.
7.5 Internal Interface
Figure 7–3 shows the block diagram of the interface between the microcontroller and its peripheral blocks.
7.6 GPI Terminal Programming
During initialization, the microcontroller fetches a control byte from its EPROM or receives a command from I2C.
7.6.1
Switch Interface
The six GPI terminals are programmed to operate in the following manner:
Table 7–1. GPI Terminal Programming
GPI5
VOL_UP, +1 dB
GPI4
GPI3
GPI2
GPI1
VOL_DN, –1 dB
x
BASS_UP, +1 dB
x
BASS_DN, –1 dB
x
TREB_UP, +1 dB
x
TREB_DN, –1 dB
x
Shift 1
x
Mute
x
EQ1
GPI0
x
x
x
EQ2
x
EQ3
x
EQ4
x
EQ5
x
Shift 2
x
x
NOTE: x = Logic low
Initially (after reset), the TAS3004 GPI is set to control volume, bass, and treble. Simultaneously setting GPI bits 1
and 5 low for 1 second changes the function of the GPI terminals to control mute and equalization.
To return to volume, bass, and treble control, simultaneously set GPI terminals 2 and 3 low for 1 second.
When a GPI switch is activated, the TAS3004 device echoes its function over I2C to a TAS3001 device mapped to
address x6Ah. Therefore, a system with two audio equalization chips can be implemented without the need for a
microcontroller.
7.6.2
GPI Architecture
The GPI provides simple but flexible input port to activate the input parameters. Each terminal input is an active logic
low.
7–4
Start
Power Up
Restore Volume
and MCR
Initialize Default
EPROM
Initialize TAS3004
TAS3001
Slave Write
Load Parameters
and Coefficients
to DSP
GPI
Power Down
Volume/Bass/Treble Up/Down
Echo to TAS3001
Switch BQ Set
Save Volume, Mute
Save PWR_DN
Stop PLL
Stop
DRC_OFF
DRC
Figure 7–3. Internal Interface Block Diagram
7–5
7.7 External EPROM Memory Maps
Table 7–2 through Table 7–5 show the 512-byte and 2048-byte EPROM memory maps.
Table 7–2. 512-Byte EPROM Memory Map 2.0 Channels
ADDRESS
BYTE NUMBER
000h
1
Signature (2Ah)
FUNCTION
001h
1
ID byte = 0000 0000
002h
1
MCR
003h–00Bh
9
Mixer left gain
00Ch–014h
9
Mixer right gain
015h–01Ah
6
DRC (ratio, threshold, energyα, attackα, decayα)
01Bh
1
Bass
01Ch
1
Treble
01Dh–022h
6
Volume
031h–03Fh
15
Biquad 0
040h–04Eh
15
Biquad 1
04Fh–05Dh
15
Biquad 2
05Eh–06Ch
15
Biquad 3
06Dh–07Bh
15
Biquad 4
07Ch–08Ah
15
Biquad 5
08Bh–099h
15
Biquad 6
09Ah
1
0 dB/bass
09Bh
1
0 dB/treble
09Ch–0A1h
6
Bass break
0A2h–0A7h
6
Treble break
0A8h–110h
105
Bass delta
111h–179h
105
Treble delta
17Ah–17Fh
6
Bass set point
180h–185h
6
Treble set point
186h–194h
15
Biquad 0
195h–1A3h
15
Biquad 1
1A4h–1B2h
15
Biquad 2
1B3h–1C1h
15
Biquad 3
1C2h–1D0h
15
Biquad 4
1D1h–1DFh
15
Biquad 5
1E0h–1EEh
15
Biquad 6
Left channel
Right channel
NOTE: Bytes are in the same order as they appear in the I2C register map. The EPROM address is xA0h.
7–6
Table 7–3. 512-Byte EPROM Memory Map 2.1 Channels (with TAS3001)
ADDRESS
BYTE NUMBER
FUNCTION
000h
1
Signature (2Ah)
001h
1
ID byte = 0000 0011
TAS3004
AD81
TAS3004
002h
1
1
MCR
TAS3001
1EFh
003h–00Bh
9
9
Mixer left gain
1F0h–1F2h
00Ch–014h
9
9
Mixer right gain
1F3h–1F5h
015h–01Ah
6
6
DRC (ratio, threshold, energyα, attackα, decayα)
1F6h–1F7h
1F8h
01Bh
1
1
Bass
01Ch
1
1
Treble
1F9h
01Dh–022h
6
6
Volume
1FAh–1FFh
031h–03Fh
15
Biquad 0
040h–04Eh
15
Biquad 1
04Fh–05Dh
15
Biquad 2
05Eh–06Ch
15
Biquad 3
06Dh–07Bh
15
Biquad 4
07Ch–08Ah
15
Biquad 5
08Bh–099h
15
Biquad 6
09Ah
1
09Bh
1
0 dB/treble
09Ch–0A1h
6
Bass break
0A2h–0A7h
6
Treble break
0A8h–110h
105
Bass delta
111h–179h
105
Treble delta
17Ah–17Fh
6
Bass set point
180h–185h
6
Treble set point
TAS3004
right and left
channel
0 dB/bass
186h–194h
15
Biquad 0
195h–1A3h
15
Biquad 1
1A4h–1B2h
15
Biquad 2
1B3h–1C1h
15
Biquad 3
1C2h–1D0h
15
Biquad 4
1D1h–1DFh
15
Biquad 5
1E0h–1EEh
15
Biquad 6
TAS3001
right and left
channel
NOTE: In this mode, the TAS3004 and the TAS3001 devices both use the same equalization coefficients for their right and left channels.
Bytes are in the same order as they appear in the I2C register map. The EPROM address is xA0h.
7–7
Table 7–4. 2048-Byte EPROM Memory Map—2.0 Speakers With Multiple Equalizations
TAS3004 ADDRESS
LEFT BIQUAD
NUMBER
OF BYTES
000h
1
001h
1
002h
1
FUNCTION
TAS3004 ADDRESS
RIGHT BIQUAD
CATEGORY
Signature (2Ah)
1
0
0
0
0
0
1
0
MCR
1EFh
003h–00Bh
9/3
Mixer left gain
1F0h–1F2h
00Ch–014h
9/3
Mixer right gain
1F3h–1F5h
015h–019h
5/2
DRC (ratio, threshold, energyα, attackα, decayα)
1F6h–1F7h
01Ah
1
Bass
1F8h
01Bh
1
Treble
1F9h
01Ch–021h
6
031h–03Fh
15
Biquad 0
Volume
3A4h–3B2h
1FAh–1FFh
186h–194h
040h–04Eh
15
Biquad 1
3B3h–3C1h
195h–1A3h
04Fh–05Dh
15
Biquad 2
3C2h–3D0h
1A4h–1B2h
05Eh–06Ch
15
Biquad 3
3D1h–3DFh
1B3h–1C1h
06Dh–07Bh
15
Biquad 4
3E0h–3EEh
1C2h–1D0h
07Ch–08Ah
15
Biquad 5
3EFh–3FDh
1D1h–1DFh
08Bh–099h
15
Biquad 6
3FEh–40Ch
1E0h–1EEh
09Ah–185h
236
200h–20Eh
15
Biquad 0
40Dh–41Bh
5B1h–5BFh
Set 0
Bass treble table
20Fh–21Dh
15
Biquad 1
41Ch–42Ah
5C0h–5CEh
21Eh–22Ch
15
Biquad 2
42Bh–439h
5CFh–5DDh
22Dh–23Bh
15
Biquad 3
43Ah–448h
5DEh–5ECh
23Ch–24Ah
15
Biquad 4
449h–457h
5EDh–5FBh
24Bh–259h
15
Biquad 5
458h–466h
5FCh–60Ah
25Ah–268h
15
Biquad 6
467h–475h
60Bh–619h
269h–277h
15
Biquad 0
476h–484h
61Ah–628h
278h–286h
15
Biquad 1
485h–493h
629h–637h
287h–295h
15
Biquad 2
494h–4A2h
638h–646h
296h–2A4h
15
Biquad 3
4A3h–4B1h
647h–655h
2A5h–2B3h
15
Biquad 4
4B2h–4C0h
656h–664h
2B4h–2C2h
15
Biquad 5
4C1h–4CFh
665h–673h
2C3h–2D1h
15
Biquad 6
4D0h–4DEh
674h–682h
2D2h–2E0h
15
Biquad 0
4DFh–4EDh
683h–691h
2E1h–2EFh
15
Biquad 1
4EEh–4FCh
692h–6A0h
2F0h–2FEh
15
Biquad 2
4FDh–50Bh
6A1h–6AFh
2FFh–30Dh
15
Biquad 3
50Ch–51Ah
6B0h–6BEh
30Eh–31Ch
15
Biquad 4
51Bh–529h
6BFh–6CDh
31Dh–32Bh
15
Biquad 5
52Ah–538h
6CEh–6DCh
32Ch–33Ah
15
Biquad 6
539h–547h
6DDh–6EBh
33Bh–349h
15
Biquad 0
548h–556h
6ECh–6FAh
34Ah–358h
15
Biquad 1
557h–565h
6FBh–709h
359h–367h
15
Biquad 2
566h–574h
70Ah–718h
368h–376h
15
Biquad 3
575h–583h
719h–727h
377h–385h
15
Biquad 4
584h–592h
728h–736h
386h–394h
15
Biquad 5
593h–5A1h
737h–745h
395h–3A3h
15
Biquad 6
5A2h–5B0h
746h–754h
Set 1
Set 2
Set 3
Set 4
NOTE: Bytes are in the same order as they appear in the I2C register map. The EPROM address is xA0h.
7–8
TAS3001
Table 7–5. 2048-Byte EPROM Memory Map—2.1 Speakers With Multiple Equalizations
TAS3004 ADDRESS
NUMBER
OF BYTES
000h
1
001h
1
002h
1
FUNCTION
TAS3001 ADDRESS
LEFT CHANNEL
CATEGORY
TAS3001 ADDRESS
RIGHT CHANNEL
Signature (2Ah)
1
0
0
0
0
0
0
1
MCR
1EFh
003h–00Bh
9/3
Mixer left gain
1F0h–1F2h
00Ch–014h
9/3
Mixer right gain
1F3h–1F5h
015h–019h
5/2
DRC (ratio, threshold, energyα, attackα, decayα)
1F6h–1F7h
01Ah
1
Bass
1F8h
01Bh
1
Treble
1F9h
01Ch–021h
6
031h–03Fh
15
Biquad 0
Volume
186h–194h
1FAh–1FFh
3A4h–3B2h
040h–04Eh
15
Biquad 1
195h–1A3h
3B3h–3C1h
04Fh–05Dh
15
Biquad 2
1A4h–1B2h
3C2h–3D0h
05Eh–06Ch
15
Biquad 3
1B3h–1C1h
3D1h–3DFh
06Dh–07Bh
15
Biquad 4
1C2h–1D0h
3E0h–3EEh
07Ch–08Ah
15
Biquad 5
1D1h–1DFh
3EFh–3FDh
08Bh–099h
15
Biquad 6
1E0h–1EEh
3FEh–40Ch
09Ah–185h
236
200h–20Eh
15
Biquad 0
5B1h–5BFh
40Dh–41Bh
Set 0
Bass treble table
20Fh–21Dh
15
Biquad 1
5C0h–5CEh
41Ch–42Ah
21Eh–22Ch
15
Biquad 2
5CFh–5DDh
42Bh–439h
22Dh–23Bh
15
Biquad 3
5DEh–5ECh
43Ah–448h
23Ch–24Ah
15
Biquad 4
5EDh–5FBh
449h–457h
24Bh–259h
15
Biquad 5
5FCh–60Ah
458h–466h
25Ah–268h
15
Biquad 6
60Bh–619h
467h–475h
269h–277h
15
Biquad 0
61Ah–628h
476h–484h
278h–286h
15
Biquad 1
629h–637h
485h–493h
287h–295h
15
Biquad 2
638h–646h
494h–4A2h
Set 1
296h–2A4h
15
Biquad 3
647h–655h
4A3h–4B1h
2A5h–2B3h
15
Biquad 4
656h–664h
4B2h–4C0h
Set 2
2B4h–2C2h
15
Biquad 5
665h–673h
4C1h–4CFh
2C3h–2D1h
15
Biquad 6
674h–682h
4D0h–4DEh
2D2h–2E0h
15
Biquad 0
683h–691h
4DFh–4EDh
2E1h–2EFh
15
Biquad 1
692h–6A0h
4EEh–4FCh
2F0h–2FEh
15
Biquad 2
6A1h–6AFh
4FDh–50Bh
2FFh–30Dh
15
Biquad 3
6B0h–6BEh
50Ch–51Ah
30Eh–31Ch
15
Biquad 4
6BFh–6CDh
51Bh–529h
31Dh–32Bh
15
Biquad 5
6CEh–6DCh
52Ah–538h
32Ch–33Ah
15
Biquad 6
6DDh–6EBh
539h–547h
33Bh–349h
15
Biquad 0
6ECh–6FAh
548h–556h
34Ah–358h
15
Biquad 1
6FBh–709h
557h–565h
359h–367h
15
Biquad 2
70Ah–718h
566h–574h
368h–376h
15
Biquad 3
719h–727h
575h–583h
377h–385h
15
Biquad 4
728h–736h
584h–592h
386h–394h
15
Biquad 5
737h–745h
593h–5A1h
395h–3A3h
15
Biquad 6
746h–754h
5A2h–5B0h
Set 3
Set 4
NOTE: Bytes are in the same order as they appear in the I2C register map. The EPROM address is xA0h.
7–9
7–10
8 Electrical Characteristics
8.1 Absolute Maximum Ratings Over Operating Temperature Ranges†
Supply voltage range:
AVDD_PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 3.6 V
DVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 3.6 V
Digital input voltage range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 to VDD + 0.3 V
Operating free-air temperature, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Case temperature for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +122°C
Lead temperature from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +97.8°C
Electrostatic discharge (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V
† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: Human body model per Method 3015.2 of MIL-STD-833B.
8.2 Recommended Operating Conditions
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V
Voltages at analog inputs and outputs and at AVDD are with respect to ground.
MIN
NOM
Supply voltage, AVDD
3.0
Supply voltage, DVDD
3.0
Supply current,
current analog
Supply current,
current digital
Power dissipation
MAX
UNIT
3.3
3.6
V
3.3
3.6
V
Operating
34
Power down (see Note 2)
88
µA
Operating
47
mA
Power down (see Note 2)
942
µA
Operating
267
mW
Power down (see Note 2)
mA
0.35
W
MIN
MAX
UNIT
NOTE 2: If the clocks are turned off.
8.3 Static Digital Specifications
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V
PARAMETER
TEST CONDITIONS
VIH
VIL
High-level input voltage
2.0
3.6
V
Low-level output voltage
–0.3
0.8
V
VOH
VOL
High-level output voltage
Low-level output voltage
Input leakage current
Output load capacitance
IO = –1 mA
IO = +4 mA
2.4
–10
V
0.4
V
10
µA
50
pF
8–1
8.4 ADC Digital Filter
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V, fS = 48 kHz, 20-bit I2S mode
All terms characterized by frequency are scaled with the chosen sampling frequency, fS. See Figure 8–1 through
Figure 8–4 for performance curves of the ADC digital filter.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
20.0
kHz
ADC decimation filter (LPF)
Pass band
0.0
Pass band ripple
±0.01
dB
Stop band
24.1
kHz
Stop band attenuation
80
Group delay
dB
720
µs
ADC high-pass filter (HPF)
Pass band (–3 dB)
Deviation from linear phase
20 Hz to 20 kHz
0.87
Hz
1.23
degrees
50
Amplitude – dB
0
–50
–100
–150
–200
0
2 fs
4 fs
6 fs
f – Frequency – Hz
8 fs
10 fs
12 fs
Figure 8–1. ADC Digital Filter Characteristics
0
Amplitude – dB
–20
–40
–60
–80
–100
0
0.2 fs
0.4 fs
0.6 fs
f – Frequency – Hz
0.8 fs
Figure 8–2. ADC Digital Filter Stopband Characteristics
8–2
1 fs
0.008
Amplitude – dB
0.006
0.004
0.002
0
–0.002
0
0.1 fs
0.2 fs
0.3 fs
f – Frequency – Hz
0.4 fs
0.5 fs
Figure 8–3. ADC Digital Filter Passband Characteristics
0.2
Amplitude – dB
0
–0.2
–0.4
–0.6
–0.8
–1
0
1 fs
2 fs
f – Frequency – Hz
3 fs
4 fs
Figure 8–4. ADC High Pass Filter Characteristics
8.5 Analog-to-Digital Converter
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V, fS = 48 kHz, 20-bit I2S mode
All terms characterized by frequency are scaled with the chosen sampling frequency, fS.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SNR (EIAJ)
A weighted
93
dB
Dynamic range
–60 dB, 1 kHz
88
dB
Signal to (noise + distortion) ratio
–1 dB, 1 kHz, 20 Hz to 20 kHz
82
dB
Power supply rejection ratio
1 kHz (see Note 3)
50
dB
Idle channel tone rejection
+110
dB
Intermodulation distortion
–80
dB
93
dB
ADC crosstalk
Overall ADC frequency response
20 Hz to 20 kHz
±0.1
Gain error
Gain matching
dB
5%
±0.02
dB
NOTE 3: Measured with a 50-mV peak sine curve.
8–3
8.6 Input Multiplexer
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V, fS = 48 kHz, 20-bit I2S mode
All terms characterized by frequency are scaled with the chosen sampling frequency, fS.
PARAMETER
TEST CONDITIONS
MIN
Input impedance
TYP
MAX
20
UNIT
kΩ
Crosstalk
85
dB
Full scale input voltage range
1.7
VPP
8.7 DAC Interpolation Filter
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V, fS = 48 kHz, 20-bit I2S mode
All terms characterized by frequency are scaled with the normal mode sampling frequency, fS. See Figure 8–5 and
Figure 8–6 for performance curves of the DAC digital filter.
PARAMETER
TEST CONDITIONS
Pass band
MIN
TYP
0.0
Pass band ripple
Stop band
Stop band attenuation
28.8 kHz to 3 MHz
kHz
dB
R
Amplitude – dB
–20
–40
–60
–80
–100
1 fs
3 fs
2 fs
f – Frequency – Hz
4 fs
5 fs
Figure 8–5. DAC Filter Overall Frequency Characteristics
Amplitude – dB
0.1
0.05
0
–0.05
–0.1
0
0.1 fs
0.2 fs
0.3 fs
f – Frequency – Hz
0.4 fs
Figure 8–6. DAC Digital Filter Passband Ripple Characteristics
8–4
kHz
24.1
0
fs/2
20.0
dB
700
0
UNIT
±0.005
75
Group delay
MAX
0.5 fs
µs
8.8 Digital-to-Analog Converter
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V, fS = 48 kHz, input = 0 dB-fS sine wave at 1 kHz
All terms characterized by frequency are scaled with the chosen sampling frequency, fS.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SNR (EIAJ)
A weighted
94
99
dB
Dynamic range
–60 dB, 1 kHz
92
96
dB
Signal to (noise + distortion) ratio
0 dB, 1 kHz, 20 Hz to 20 kHz
83
dB
Power supply rejection ratio
1 kHz
50
dB
+118
dB
Idle channel tone rejection
Intermodulation distortion
–75
Frequency response
–0.5
Deviation from linear phase
dB
+0.5
dB
±1.4
degree
DAC crosstalk
–96
dB
Jitter tolerance
150
ps
Full scale, single-ended, output voltage range
1.9
DC offset
–7.0
7.0
VPP
mV
MAX
UNIT
8.9 DAC Output Performance Data
TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V
The output load resistance is connected through a dc blocking capacitor.
PARAMETER
Output load resistance
TEST CONDITIONS
MIN
TYP
10
kΩ
Output load capacitance
25
VCOM internal resistance (see Note 4)
1
VCOM output CLOAD
10
VRFILT internal resistance (see Note 5)
1
pF
kΩ
100
µF
kΩ
NOTES: 4. VCOM may vary during power down.
5. VRFILT must never be used as a voltage reference.
8–5
8.10 I2C Serial Port Timing Characteristics
MIN
MAX
UNIT
0
100
kHz
fscl
tbuf
SCL clock frequency
Bus free time between start and stop
4.7
µs
tlow
thigh
Low period of SCL clock
4.7
µs
High period of SCL clock
4.0
µs
thdsta
tsusta
Hold time repeated start
4.0
Setup time repeated start
4.7
thddat
tsudat
Data hold time (See Note 6)
tr
tf
Rise time for SDA and SCL
tsusto
Cb
Setup time for stop condition
µs
20
µs
0
Data setup time
250
ns
1000
Fall time for SDA and SCL
300
ns
ns
µs
4.0
Capacitive load for each bus line
µs
400
pF
NOTE 6: A device must internally provide a hold time of at least 300 ns for the SDA signal to bridge the undefined region of the falling edge of
SCL.
P
S
P
SDA
Valid
tHD(DAT)
tBUF
tr
SCL
tsu(STA)
tsu(DAT)
tsu(STO)
Change
of Data
Allowed
Data
Line
Stable
tf
tHD(STA)
NOTE: tlow is measured from the end of tf to the beginning of tr.
thigh is measured from the end of tr to the beginning of tf.
Figure 8–7. I2C Bus Timing
8–6
tHD(STA)
9 System Diagrams
Figure 9–1 and Figure 9–2 show the TAS3004 stereo and 2.1-channel applications, respectively.
+3.3 VDD
Analog In
SPDIF
or
USB
EPROM
I2S
I2C
Clock Select Logic
RESET
Analog Out
TAS3004
Master
B-T-V-EQ Switches
NOTE: Items such as the PLL network and power supplies are omitted for clarity.
Figure 9–1. Stereo Application
9–1
+3.3 VDD
Analog In
SPDIF
or
USB
EPROM
Echos
Switches
on GPIO
I2S
I2C
Clock Select Logic
RESET
Master
Analog Out
(To Satellite Amplifiers)
TAS3004
SDOUT2
I2S_OUT
B-T-V-EQ-Sub Vol
L+R Mix
I2C
Slave
I2S PCM1744
TAS3001
Address = 6Ah
NOTE: Items such as the PLL network and power supplies are omitted for clarity.
Figure 9–2. TAS3004 Device, 2.1 Channels
9–2
Analog Out
10 Mechanical Information
The TAS3004 device is packaged in a 48-terminal PFB package. The following illustration shows the mechanical
dimensions for the PFB package.
PFB (S-PQFP-G48)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
36
0,08 M
25
37
24
48
13
0,13 NOM
1
12
5,50 TYP
7,20
SQ
6,80
9,20
SQ
8,80
Gage Plane
0,25
0,05 MIN
0°–ā7°
1,05
0,95
Seating Plane
1,20 MAX
0,75
0,45
0,08
4073176/B 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
10–1
10–2
Appendix A
Software Interface
Table A–1. I2C Register Map
REGISTER
ADDRESS
NUMBER OF
BYTES
BYTE DESCRIPTION
Reserved
0x00
Main control
0x01
1
C(7–0)
DRC
0x02
5
Ratio(7–0), Threshold(7–0), Energy(7–0), Attack(7–0), Decay(7–0)
Reserved
0x03
Volume
0x04
6
VL(23–16), VL(15–8), VL(7–0)
VR(23–16), VR(15–8), VR(7–0)
Treble
0x05
1
T(7–0)
Bass
0x06
1
B(7–0)
Mixer left gain
0x07
9
S1L(23–16), S1L(15–8), S1L(7–0)
S2L(23–16), S2L(15–8), S2L(7–0)
AIL(23–16), AIL(15–8), AIL(7–0)
Mixer right gain
0x08
9
S1R(23–16), S1R(15–8), S1R(7–0)
S2R(23–16), S2R(15–8), S2R(7–0)
AIR(23–16), AIR(15–8), AIR(7–0)
Reserved
0x09
Left biquad 0
0x0A
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Left biquad 1
0x0B
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Left biquad 2
0x0C
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Left biquad 3
0x0D
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Left biquad 4
0x0E
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Left biquad 5
0x0F
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
A–1
Table A–1. I2C Register Map (Continued)
REGISTER
Left biquad 6
ADDRESS
NUMBER OF
BYTES
0x10
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
BYTE DESCRIPTION
Reserved
0x11
Reserved
0x12
Right biquad 0
0x13
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Right biquad 1
0x14
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Right biquad 2
0x15
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Right biquad 3
0x16
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Right biquad 4
0x17
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Right biquad 5
0x18
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Right biquad 6
0x19
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Reserved
0x20
Left loudness
biquad
0x21
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
Right loudness
biquad
0x22
15
B0(23–16), B0(15–8), B0(7–0)
B1(23–16), B1(15–8), B1(7–0)
B2(23–16), B2(15–8), B2(7–0)
A1(23–16), A1(15–8), A1(7–0)
A2(23–16), A2(15–8), A2(7–0)
A–2
Table A–1. I2C Register Map (Continued)
ADDRESS
NUMBER OF
BYTES
Left loudness
biquad gain
0x23
3
LBG(23–16), LBG(15–8), LBG(7–0)
Right loudness
biquad gain
0x24
3
RBG(23–16), RBG(15–8), RBG(7–0)
0x29
10
Reserved
Anal_ctrl(7–0)
REGISTER
Test
Reserved
BYTE DESCRIPTION
0x30 to 0xFF
Analog control
0x40
1
Test
0x41
1
Test
0x42
1
Main control 2
0x43
1
MCR2(7–0)
A.1 Main Control Register Map
A.1.1
Main Control Register 1
MCR 0X01
C(7)
C(6)
C(5)
C(4)
C(3)
C(2)
C(1)
C(0)
FL
SC
E1
E0
F1
F0
W1
W0
1
x
x
x
x
x
x
x
Table A–2. Main Control Register 1 Description
REGISTER
DESCRIPTOR
C(7)
( )
FL
C(6)
( )
C(5–4)
(
)
SC
E(1–0)
(
)
C(3)
FUNCTION
VALUE
Fast load
SCLK frequency
q
y
Serial port mode
XX
C(2)
C(1–0)
(
)
A.1.2
W(1–0)
(
)
Serial port word
length
DESCRIPTION
0
Normal operation mode
1
Fast load mode
0
SCLK = 32fS
1
SCLK = 64fS
00
Left justified
01
10
Right justified
I2S
11
Reserved
1
Reserved
0
Download
00
16-bit
01
18-bit
10
20-bit
11
24-bit
Main Control Register 2
MCR2 0X43
C2(7)
C2(6)
C2(5)
C2(4)
C2(3)
C2(2)
C2(1)
C2(0)
DL
XX
XX
XX
XX
XX
AP
XX
1
0
0
0
0
0
1
0
A–3
Table A–3. Main Control Register 2 Description
REGISTER
DESCRIPTOR
C2(7)
( )
DL
FUNCTION
VALUE
DESCRIPTION
Bass and treble
load
0
Normal operation mode
1
Downloaded values
0
C2(6)
( )
XX
Reserved
C2(5)
( )
XX
Reserved
C2(4)
( )
XX
Reserved
1
0
1
0
1
C2(3)
( )
XX
Reserved
C2(2)
( )
XX
Reserved
C2(1)
( )
AP
Allpass mode
C2(0)
( )
XX
Reserved
0
1
0
1
0
Normal operation
1
Sets equalization filters to all pass
0
1
A.1.3
Analog Control Register
ANA 0X40
A(7)
A(6)
A(5)
A(4)
A(3)
A(2)
A(1)
A(0)
ADM
LRB
XX
XX
DM1
DM0
INP
APD
0
0
0
0
1
1
1
1
Table A–4. Analog Control Register Description
REGISTER
DESCRIPTOR
FUNCTION
VALUE
A(7)
( )
ADM
ADC output mode
0
Normal operation
1
B inputs are monaural
Selects left or
right
g B input for
monaural output
0
B left input selected for monaural ADC output when bit 7 (ADM)
is set to 1
1
B right input selected for monaural ADC output when bit 7 (ADM)
is set to 1
0
A(6)
LRB
DESCRIPTION
A(5)
( )
XX
Reserved
A(4)
( )
XX
Reserved
0
A(3–2)
(
)
DM(1–0)
(
)
De-emphasis
control
00
De-emphasis off, normal operation
01
De-emphasis for fS = 48 kHz
10
De-emphasis for fS = 44.1 kHz
11
Reserved
1
1
A–4
A(1)
( )
INP
Analog
g input
select
0
A inputs selected
1
B inputs selected
A(0)
( )
APD
Analog
g power
down
1
Powers down analog section
0
Normal operation
A.2 Volume Gain Command
The gain error is less than 0.12 dB (exclusive mute).
Device ID
Subaddress
VL(23–16)
VL(15–8)
VL(7–0)
VR(23–16)
VR(15–8)
VR(7–0)
80
4E
For example, if left volume = 6 dB and right volume = –6 dB, then the command is:
68
04
01
FE
CA
00
Table A–5. Volume Versus Gain Values
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
18.0
07, F1, 7B
3.0
01, 69, 9C
–12.0
00, 40, 4E
–27.0
00, 0B, 6F
–42.0
00, 02, 09
17.5
07, 7F, BB
2.5
01, 55, 62
–12.5
00, 3C, B5
–27.5
00, 0A, CC
–42.5
00, 01, EB
17.0
07, 14, 57
2.0
01, 42, 49
–13.0
00, 39, 50
–28.0
00, 0A, 31
–43.0
00, 01, D0
16.5
06, AE, F6
1.5
01, 30, 42
–13.5
00, 36, 1B
–28.5
00, 09, 9F
–43.5
00, 01, B6
16.0
06, 4F, 40
1.0
01, 1F, 3D
–14.0
00, 33, 14
–29.0
00, 09, 15
–44.0
00, 01, 9E
15.5
05, F4, E5
0.5
01, 0F, 2B
–14.5
00, 30, 39
–29.5
00, 08, 93
–44.5
00, 01, 86
15.0
05, 9F, 98
0.0
01, 00, 00
–15.0
00, 2D, 86
–30.0
00, 08, 18
–45.0
00, 01, 71
14.5
05, 4F, 10
–0.5
00, F1, AE
–15.5
00, 2A, FA
–30.5
00, 07, A5
–45.5
00, 01, 5C
14.0
05, 03, 0A
–1.0
00, E4, 29
–16.0
00, 28, 93
–31.0
00, 07, 37
–46.0
00, 01, 48
13.5
04, BB, 44
–1.5
00, D7, 66
–16.5
00, 26, 4E
–31.5
00, 06, D0
–46.5
00, 01, 36
13.0
04, 77, 83
–2.0
00, CB, 59
–17.0
00, 24, 29
–32.0
00, 06, 6E
–47.0
00, 01, 25
12.5
04, 37, 8B
–2.5
00, BF, F9
–17.5
00, 22, 23
–32.5
00, 06, 12
–47.5
00, 01, 14
12.0
03, FB, 28
–3.0
00, B5, 3C
–18.0
00, 20, 3A
–33.0
00, 05, BB
–48.0
00, 01, 05
11.5
03, C2, 25
–3.5
00, AB, 19
–18.5
00, 1E, 6D
–33.5
00, 05, 69
–48.5
00, 00, F6
11.0
03, 8C, 53
–4.0
00, A1, 86
–19.0
00, 1C, B9
–34.0
00, 05, 1C
–49.0
00, 00, E9
10.5
03, 59, 83
–4.5
00, 98, 7D
–19.5
00, 1B, 1E
–34.5
00, 04, D2
–49.5
00, 00, DC
10.0
03, 29, 8B
–5.0
00, 8F, F6
–20.0
00, 19, 9A
–35.0
00, 04, 8D
–50.0
00, 00, CF
9.5
02, FC, 42
–5.5
00, 87, E8
–20.5
00, 18, 2B
–35.5
00, 04, 4C
–50.5
00, 00, C4
9.0
02, D1, 82
–6.0
00, 80, 4E
–21.0
00, 16, D1
–36.0
00, 04, 0F
–51.0
00, 00, B9
8.5
02, A9, 25
–6.5
00, 79, 20
–21.5
00, 15, 8A
–36.5
00, 03, D5
–51.5
00, 00, AE
8.0
02, 83, 0B
–7.0
00, 72, 5A
–22.0
00, 14, 56
–37.0
00, 03, 9E
–52.0
00, 00, A5
7.5
02, 5F, 12
–7.5
00, 6B, F4
–22.5
00, 13, 33
–37.5
00, 03, 6A
–52.5
00, 00, 9B
7.0
02, 3D, 1D
–8.0
00, 65, EA
–23.0
00, 12, 20
–38.0
00, 03, 39
–53.0
00, 00, 93
6.5
02, 1D, 0E
–8.5
00, 60, 37
–23.5
00, 11, 1C
–38.5
00, 03, 0B
–53.5
00, 00, 8B
6.0
01, FE, CA
–9.0
00, 5A, D5
–24.0
00, 10, 27
–39.0
00, 02, DF
–54.0
00, 00, 83
5.5
01, E2, 37
–9.5
00, 55, C0
–24.5
00, 0F, 40
–39.5
00, 02, B6
–54.5
00, 00, 7B
5.0
01, C7, 3D
–10.0
00, 50, F4
–25.0
00, 0E, 65
–40.0
00, 02, 8F
–55.0
00, 00, 75
4.5
01, AD, C6
–10.5
00, 4C, 6D
–25.5
00, 0D, 97
–40.5
00, 02, 6B
–55.5
00, 00, 6E
4.0
01, 95, BC
–11.0
00, 48, 27
–26.0
00, 0C, D5
–41.0
00, 02, 48
–56.0
00, 00, 68
3.5
01, 7F, 09
–11.5
00, 44, 1D
–26.5
00, 0C, 1D
–41.5
00, 02, 27
–56.5
00, 00, 62
A–5
Table A–5. Volume Versus Gain Values (Continued)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
VOLUME
V(23–16),
V(15–8),
V(7–0)
GAIN (dB)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
GAIN (dB)
VOLUME
V(23–16),
V(15–8),
V(7–0)
–57.0
00, 00, 5D
–60.0
00, 00, 42
–63.0
00, 00, 2E
–66.0
00, 00, 21
–69.0
00, 00, 17
–57.5
00, 00, 57
–60.5
00, 00, 3E
–63.5
00, 00, 2C
–66.5
00, 00, 1F
–69.5
00, 00, 16
–58.0
00, 00, 53
–61.0
00, 00, 3A
–64.0
00, 00, 29
–67.0
00, 00, 1D
–70.0
00, 00, 15
–58.5
00, 00, 4E
–61.5
00, 00, 37
–64.5
00, 00, 27
–67.5
00, 00, 1C
mute
00, 00, 00
–59.0
00, 00, 4A
–62.0
00, 00, 34
–65.0
00, 00, 25
–68.0
00, 00, 1A
–59.5
00, 00, 45
–62.5
00, 00, 31
–65.5
00, 00, 23
–68.5
00, 00, 19
A.3 Treble Control Register Command
Both left and right channel are given the same treble gain setting.
Device ID
Subaddress
T(7–0)
For example, if treble gain = 5 dB, then the command is:
68
05
65
Table A–6. Treble Control Register
GAIN (dB)
T(7–0)
(hex)
GAIN (dB)
18.0
0x01
17.5
0x01
17.0
A–6
T(7–0)
(hex)
GAIN (dB)
T(7–0)
(hex)
GAIN (dB)
T(7–0)
(hex)
GAIN (dB)
T(7–0)
(hex)
10.5
0x4A
10.0
0x4D
3.0
0x6B
2.5
0x6C
–4.5
0x7B
–12.0
0x8A
–5.0
0x7C
–12.5
0x04
9.5
0x51
2.0
0x8B
0x6D
–5.5
0x7D
–13.0
0x8C
16.5
0x08
16.0
0x13
9.0
0x53
8.5
0x56
1.5
0x3F
–6.0
0x7E
–13.5
0x8D
1.0
0x70
–6.5
0x7F
–14.0
0x8E
15.5
0x1A
15.0
0x20
8.0
7.5
0x59
0.5
0x71
–7.0
0x80
–14.5
0x8F
0x5B
0.0
0x72
–7.5
0x81
–15.0
14.5
0x26
7.0
0x90
0x5D
–0.5
0x73
–8.0
0x82
–15.5
0x91
14.0
0x2C
13.5
0x31
6.5
0x60
–1.0
0x74
–8.5
0x83
–16.0
0x92
6.0
0x62
–1.5
0x75
–9.0
0x84
–16.5
0x93
13.0
12.5
0x36
5.5
0x63
–2.0
0x76
–9.5
0x85
–17.0
0x94
0x3B
5.0
0x65
–2.5
0x77
–10.0
0x86
–17.5
12.0
0x95
0x3F
4.5
0x67
–3.0
0x78
–10.5
0x87
–18.0
0x96
11.5
0x43
4.0
0x68
–3.5
0x79
–11.0
0x88
11.0
0x47
3.5
0x69
–4.0
0x7A
–11.5
0x89
A.4 Bass Control Register Command
Both left and right channel are given the same bass gain setting.
Device ID
Subaddress
B(7–0)
For example, if bass gain = 5 dB, then the command is:
68
06
2B
Table A–7. Bass Control Register
GAIN (dB)
B(7–0)
(hex)
GAIN (dB)
B(7–0)
(hex)
GAIN (dB)
B(7–0)
(hex)
GAIN (dB)
B(7–0)
(hex)
GAIN (dB)
B(7–0)
(hex)
18.0
0x01
10.5
0x4C
3.0
0x6A
–4.5
0x7B
–12.0
0x8A
17.5
0x0A
10.0
0x4F
2.5
0x6B
–5.0
0x7C
–12.5
0x8B
17.0
0x11
9.5
0x52
2.0
0x6D
–5.5
0x7D
–13.0
0x8C
16.5
0x18
9.0
0x55
1.5
0x6E
–6.0
0x7E
–13.5
0x8D
16.0
0x1E
8.5
0x58
1.0
0x6F
–6.5
0x7F
–14.0
0x8E
15.5
0x24
8.0
0x5B
0.5
0x71
–7.0
0x80
–14.5
0x8F
15.0
0x29
7.5
0x5D
0.0
0x72
–7.5
0x81
–15.0
0x90
14.5
0x2E
7.0
0x5F
–0.5
0x73
–8.0
0x82
–15.5
0x91
14.0
0x33
6.5
0x61
–1.0
0x74
–8.5
0x83
–16.0
0x92
13.5
0x37
6.0
0x62
–1.5
0x75
–9.0
0x84
–16.5
0x93
13.0
0x3B
5.5
0x63
–2.0
0x76
–9.5
0x85
–17.0
0x94
12.5
0x3F
5.0
0x65
–2.5
0x77
–10.0
0x86
–17.5
0x95
12.0
0x43
4.5
0x66
–3.0
0x78
–10.5
0x87
–18.0
0x96
11.5
0x46
4.0
0x67
–3.5
0x79
–11.0
0x88
11.0
0x49
3.5
0x69
–4.0
0x7A
–11.5
0x89
A.5 I2C Mixer Register Command
The gain error is less than 0.12 dB, excluding mute.
Device ID
Subaddress
Mixer1
Mixer2
ADC Mixer
For example, if Sdin1 Mix = +6dB, Sdin2 Mix = 0dB, and ADC Mix = Mute, then the command is:
Left
68
07
1F EC 98
10 00 00
00 00 00
68
08
1F EC 98
10 00 00
00 00 00
Right
Even if only one of the mixers needs to be changed, the whole command must be sent.
A–7
Table A–8. Mixer1 and Mixer2 Gain Values
GAIN (dB)
A–8
GAIN
S(23–16),
S(15–8),
S(7–0)
GAIN (dB)
GAIN
S(23–16),
S(15–8),
S(7–0)
GAIN (dB)
GAIN
S(23–16),
S(15–8),
S(7–0)
GAIN (dB)
GAIN
S(23–16),
S(15–8),
S(7–0)
GAIN (dB)
GAIN
S(23–16),
S(15–8),
S(7–0)
18.0
7F, 17, AF
0.0
10, 00, 00
–18.0
02, 03, A7
–36.0
00, 40, EA
–54.0
00, 08, 2C
17.5
77, FB, AA
–0.5
0F, 1A, DF
–18.5
01, E6, CF
–36.5
00, 3D, 49
–54.5
00, 07, B7
17.0
71, 45, 75
–1.0
0E, 42, 90
–19.0
01, CB, 94
–37.0
00, 39, DB
–55.0
00, 07, 48
16.5
6A, EF, 5D
–1.5
0D, 76, 5A
–19.5
01, B1, DE
–37.5
00, 36, 9E
–55.5
00, 06, E0
16.0
64, F4, 03
–2.0
0C, B5, 91
–20.0
01, 99, 99
–38.0
00, 33, 90
–56.0
00, 06, 7D
15.5
5F, 4E, 52
–2.5
0B, FF, 91
–20.5
01, 82, AF
–38.5
00, 30, AE
–56.5
00, 06, 20
15.0
59, F9, 80
–3.0
0B, 53, BE
–21.0
01, 6D, 0E
–39.0
00, 2D, F5
–57.0
00, 05, C9
14.5
54, F1, 06
–3.5
0A, B1, 89
–21.5
01, 58, A2
–39.5
00, 2B, 63
–57.5
00, 05, 76
14.0
50, 30, A1
–4.0
0A, 18, 66
–22.0
01, 45, 5B
–40.0
00, 28, F5
–58.0
00, 05, 28
13.5
4B, B4, 46
–4.5
09, 87, D5
–22.5
01, 33, 28
–40.5
00, 26, AB
–58.5
00, 04, DE
13.0
47, 78, 28
–5.0
08, FF, 59
–23.0
01, 21, F9
–41.0
00, 24, 81
–59.0
00, 04, 98
12.5
43, 78, B0
–5.5
08, 7E, 80
–23.5
01, 11, C0
–41.5
00, 22, 76
–59.5
00, 04, 56
12.0
3F, B2, 78
–6.0
08, 04, DC
–24.0
01, 02, 70
–42.0
00, 20, 89
–60.0
00, 04, 18
11.5
3C, 22, 4C
–6.5
07, 92, 07
–24.5
00, F3, FB
–42.5
00, 1E, B7
–60.5
00, 03, DD
11.0
38, C5, 28
–7.0
07, 25, 9D
–25.0
00, E6, 55
–43.0
00, 1C, FF
–61.0
00, 03, A6
10.5
35, 98, 2F
–7.5
06, BF, 44
–25.5
00, D9, 73
–43.5
00, 1B, 60
–61.5
00, 03, 72
10.0
32, 98, B0
–8.0
06, 5E, A5
–26.0
00, CD, 49
–44.0
00, 19, D8
–62.0
00, 03, 40
9.5
2F, C4, 20
–8.5
06, 03, 6E
–26.5
00, C1, CD
–44.5
00, 18, 65
–62.5
00, 03, 12
9.0
2D, 18, 18
–9.0
05, AD, 50
–27.0
00, B6, F6
–45.0
00, 17, 08
–63.0
00, 02, E6
8.5
2A, 92, 54
–9.5
05, 5C, 04
–27.5
00, AC, BA
–45.5
00, 15, BE
–63.5
00, 02, BC
8.0
28, 30, AF
–10.0
05, 0F, 44
–28.0
00, A3, 10
–46.0
00, 14, 87
–64.0
00, 02, 95
7.5
25, F1, 25
–10.5
04, C6, D0
–28.5
00, 99, F1
–46.5
00, 13, 61
–64.5
00, 02, 70
7.0
23, D1, CD
–11.0
04, 82, 68
–29.0
00, 91, 54
–47.0
00, 12, 4B
–65.0
00, 02, 4D
6.5
21, D0, D9
–11.5
04, 41, D5
–29.5
00, 89, 33
–47.5
00, 11, 45
–65.5
00, 02, 2C
6.0
1F, EC, 98
–12.0
04, 04, DE
–30.0
00, 81, 86
–48.0
00, 10, 4E
–66.0
00, 02, 0D
5.5
1E, 23, 6D
–12.5
03, CB, 50
–30.5
00, 7A, 48
–48.5
00, 0F, 64
–66.5
00, 01, F0
5.0
1C, 73, D5
–13.0
03, 94, FA
–31.0
00, 73, 70
–49.0
00, 0E, 88
–67.0
00, 01, D4
4.5
1A, DC, 61
–13.5
03, 61, AF
–31.5
00, 6C, FB
–49.5
00, 0D, B8
–67.5
00, 01, BA
4.0
19, 5B, B8
–14.0
03, 31, 42
–32.0
00, 66, E3
–50.0
00, 0C, F3
–68.0
00, 01, A1
3.5
17, F0, 94
–14.5
03, 03, 8A
–32.5
00, 61, 21
–50.5
00, 0C, 3A
–68.5
00, 01, 8A
3.0
16, 99, C0
–15.0
02, D8, 62
–33.0
00, 5B, B2
–51.0
00, 0B, 8B
–69.0
00, 01, 74
2.5
15, 56, 1A
–15.5
02, AF, A3
–33.5
00, 56, 91
–51.5
00, 0A, E5
–69.5
00, 01, 5F
2.0
14, 24, 8E
–16.0
02, 89, 2C
–34.0
00, 51, B9
–52.0
00, 0A, 49
–70.0
00, 01, 4B
1.5
13, 04, 1A
–16.5
02, 64, DB
–34.5
00, 4D, 27
–52.5
00, 09, B6
Mute
00, 00, 00
1.0
11, F3, C9
–17.0
02, 42, 93
–35.0
00, 48, D6
–53.0
00, 09, 2B
0.5
10, F2, B4
–17.5
02, 22, 35
–35.5
00, 44, C3
–53.5
00, 08, A8
A.6 Programming Instruction for the Loudness Contour
The gain error is less than 0.12 dB, excluding mute.
Device ID
Subaddress
B0(23–0)
B1(23–0)
B2(23–0)
A1(23–0)
A2(23–0)
001A82
000000
FFE57E
E03550
0FCABB
001A82
000000
FFE57E
E03550
0FCABB
For example:
Left Loudness Biquad
68
21
Right Loudness Biquad
68
22
Left Loudness Biquad Gain
68
Sub
G(23–0)
23
04C6D0
24
04C6D0
Right Loudness Biquad Gain
68
A.7 Examples of DRCE
The gain error is less than 0.12 dB (excluding mute).
Table A–9. Example of a DRCE I2C Instruction With DRCE On
BYTE
NUMBER
INSTRUCTION
(HEX)
1
68
TAS3004 device identification
2
02
DRC subaddress
3
68
Above-threshold ratio of 5.33:1 with DRCE on
See Table A–11 and Table A–12
4
22
Below-threshold ratio of 1.33:1
See Table A–13 and Table A–14
5
9F
Threshold of –30 dB
See Table A–15
6
B0
Integration interval for energy level detection of 212 ms
See Table A–16
7
60
Attack time constant 6.7 ms
8
A0
Decay time constant 106 ms
A.7.1
INSTRUCTION DEFINITION
TABLE
DRCE On/Off
The DRCE default mode in the TAS3004 device is off.
The DRCE turns on if all eight bytes in Table A–9 are transmitted and the LSB of the above threshold ratio byte is
0.
The DRCE turns off if all eight bytes in Table A–10 are transmitted and the LSB of the above threshold ratio byte is
1. Table A–10 is identical to Table A–9 except for this third byte.
Table A–10. Example of a DRCE I2C Instruction With DRCE Off
BYTE
NUMBER
INSTRUCTION
(HEX)
1
68
TAS3004 device identification
2
02
DRC subaddress
3
69
Above threshold ratio of 5.33:1 with DRCE off
See Table A–11 and Table A–12
4
22
Below threshold ratio of 1.33:1
See Table A–13 and Table A–14
5
9F
Threshold of –30 dB
See Table A–15
6
B0
Integration interval for energy level detection of 212 ms
See Table A–16
7
60
Attack time constant 6.7 ms
8
A0
Decay time constant 106 ms
INSTRUCTION DEFINITION
TABLE
A–9
A.7.2
Above Threshold Ratios
The above threshold ratios are applied when the energy level of the incoming signal is detected anywhere between
the threshold (from Table A–15) and 0 dB. See Figure A–1.
Output (dB)
0 dB
Ratio = 1:1
Expansion
Compression
–89.625 dB
–89.625 dB
Input (dB)
Threshold
Below Threshold
0 dB
Above Threshold
Figure A–1. TAS3004 DRCE Characteristics in the dB Domain
Table A–11. Above Threshold Ratios for Compression
A–10
HEXADECIMAL VALUE
RATIO (IN:OUT)
02
1.00 : 1
08
1.07 : 1
10
1.14 : 1
18
1.23 : 1
20
1.33 : 1
28
1.45 : 1
30
1.60 : 1
38
1.78 : 1
40
2.00 : 1
48
2.29 : 1
50
2.67 : 1
58
3.20 : 1
60
4.00 : 1
68
5.33 : 1
70
8.00 : 1
78
16.0 : 1
Table A–12. Above Threshold Ratios for Expansion
A.7.3
HEXADECIMAL VALUE
RATIO (IN:OUT)
02
1 : 1.00
0A
1 : 1.06
12
1 : 1.13
1A
1 : 1.19
22
1 : 1.25
2A
1 : 1.31
32
1 : 1.38
3A
1 : 1.44
42
1 : 1.50
Below Threshold Ratios
The below threshold ratios are applied when the energy level of the incoming signal is detected as being anywhere
between the threshold (from Table A–15) and –89.625 dB. See Figure A–1.
Table A–13. Below Threshold Ratios for Expansion
HEXADECIMAL VALUE
RATIO (IN:OUT)
02
1 : 1.00
08
1 : 1.06
10
1 : 1.13
18
1 : 1.19
20
1 : 1.25
28
1 : 1.31
30
1 : 1.38
38
1 : 1.44
40
1 : 1.50
48
1 : 1.56
50
1 : 1.63
58
1 : 1.69
60
1 : 1.75
68
1 : 1.81
70
1 : 1.88
78
1 : 1.94
80
1 : 2.00
Table A–14. Below Threshold Ratios for Compression
HEXADECIMAL VALUE
RATIO (IN:OUT)
02
1.00 : 1
0A
1.07 : 1
12
1.14 : 1
1A
1.23 : 1
22
1.33 : 1
2A
1.45 : 1
32
1.60 : 1
3A
1.78 : 1
42
2.00 : 1
A–11
A.7.4
Threshold
Table A–15 lists a range of threshold values from 0 dB to –89.625 dB in 0.75-dB decrements.
NOTE: The TAS3004 device is capable of 0.375-dB increments. The associated hexidecimal
value can be determined by interpolating between the existing hexidecimal values in
Table A–15.
Table A–15. Threshold Values
HEX
VALUE
dB
HEX
VALUE
dB
HEX
VALUE
dB
HEX
VALUE
dB
HEX
VALUE
dB
EF
0
BD
–18.75
8B
–37.50
59
–56.25
27
–75.00
ED
–0.75
BB
–19.50
89
–38.25
57
–57.00
25
–75.75
EB
–1.50
B9
–20.25
87
–39.00
55
–57.75
23
–76.50
E9
–2.25
B7
–21.00
85
–39.75
53
–58.50
21
–77.25
E7
–3.00
B5
–21.75
83
–40.50
51
–59.25
1F
–78.00
E5
–3.75
B3
–22.50
81
–41.25
4F
–60.00
1D
–78.75
E3
–4.50
B1
–23.25
7F
–42.00
4D
–60.75
1B
–79.50
E1
–5.25
AF
–24.00
7D
–42.75
4B
–61.50
19
–80.25
DF
–6.00
AD
–24.75
7B
–43.50
49
–62.25
17
–80.00
DD
–6.75
AB
–25.50
79
–44.25
47
–63.00
15
–81.75
DB
–7.50
A9
–26.25
77
–45.00
45
–63.75
13
–82.50
D9
–8.25
A7
–27.00
75
–45.75
43
–64.50
11
–83.25
D7
–9.00
A5
–27.75
73
–46.50
41
–65.25
0F
–84.00
D5
–9.75
A3
–28.50
71
–47.25
3F
–66.00
0D
–84.75
D3
–10.50
A1
–29.25
6F
–48.00
3D
–66.75
0B
–85.50
D1
–11.25
9F
–30.00
6D
–48.75
3B
–67.50
09
–86.25
CF
–12.00
9D
–30.75
6B
–49.50
39
–68.25
07
–87.00
CD
–12.75
9B
–31.50
69
–50.25
37
–69.00
05
–87.75
CB
–13.50
99
–32.25
67
–51.00
35
–69.75
03
–88.50
C9
–14.25
97
–33.00
65
–51.75
33
–70.50
01
–89.25
C7
–15.00
95
–33.75
63
–52.50
31
–71.25
00
–89.625
C5
–15.75
93
–34.50
61
–53.25
2F
–72.00
C3
–16.50
91
–35.25
5F
–54.00
2D
–72.75
C1
–17.25
8F
–36.00
5D
–54.75
2B
–73.50
BF
–18.00
8D
–36.75
5B
–55.50
29
–74.25
A.7.5
Time Constants
Use Table A–16 to program the attack time, the decay time, and the integration interval for energy level detection.
Level detection is performed by using an alpha filter at the input of the DRCE, which functions as an energy-level
detection block for the DRCE. The time constant for level detection can be thought of as an integration interval. Use
a time constant from Table A–16 as an integration interval for energy level detection.
Table A–16 lists the time constants used for integration interval for energy level detection, attack time constant, and
decay time constant. All values represent the time required to reach 63% of maximum value from zero.
A–12
Table A–16. Time Constants
A.7.6
HEXADECIMAL VALUE
TIME DELAY
40
1.7 ms
50
3.5 ms
60
6.7 ms
70
13 ms
80
26 ms
90
53 ms
A0
106 ms
B0
212 ms
C0
425 ms
D0
850 ms
E0
1.7 s
F0
2.4 s
DRCE Example With Threshold at –12 dB
From the DRCE example shown in Figure A–2, the threshold is set at –12 dB. The input energy E, has a value of
–6 dB.
Output (dB) = [T(dB) + ( E(dB) – T(dB) ) x (1/CR)]
= [–12 + (–6 – (–12)) x (1/3)] dB
= –12 + 2 = –10 dB
Where:
CR = Compression Ratio
T = Threshold (dB)
E = Energy estimate of current input
Note: Energy of sine wave is approximately 3 dB lower than peak.
Output (dB)
0 dB
Final Output = –10 dB
Threshold = –12 dB
3:1 Above Threshold
Ratio for Compression
1:1 Below Threshold
Ratio for Compression
Input (dB)
Threshold = –12 dB
E = –6 dB
0 dB
Figure A–2. DRCE Example With Threshold at –12 dB
A–13
A–14