Order this document by MURF820/D SEMICONDUCTOR TECHNICAL DATA Motorola Preferred Device Designed for use in switching power supplies, inverters and as free wheeling diodes, these state–of–the–art devices have the following features: • • • • • • • • ULTRAFAST RECTIFIER 8 AMPERES 200 VOLTS Ultrafast 35 ns Recovery Times 150°C Operating Junction Temperature Epoxy Meets UL94, VO @ 1/8″ High Temperature Glass Passivated Junction Low Leakage Specified @ 150°C Case Temperature Current Derating @ Both Case and Ambient Temperatures Electrically Isolated. No Isolation Hardware Required. UL Recognized File #E69369(1) Mechanical Characteristics • Case: Epoxy, Molded • Weight: 1.9 grams (approximately) • Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable • Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds • Shipped 50 units per plastic tube • Marking: U820 1 3 1 3 CASE 221E–01 ISOLATED TO–220 MAXIMUM RATINGS Rating Symbol Value Unit Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage VRRM VRWM VR 200 Volts Average Rectified Forward Current (Rated VR), TC = 150°C IF(AV) 8 Amps IFM 16 Amps IFSM 100 Amps TJ, Tstg – 65 to +150 °C Viso1 Viso2 Viso3 4500 3500 1500 Volts RθJC 4.2 °C/W TL 260 °C Peak Repetitive Forward Current (Rated VR, Square Wave, 20 kHz), TC = 150°C Non–repetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) Operating Junction and Storage Temperature RMS Isolation Voltage (t = 1 second, R.H. ≤ 30%, TA = 25°C) (2) Per Figure 3 Per Figure 4 (1) Per Figure 5 THERMAL CHARACTERISTICS Maximum Thermal Resistance, Junction to Case Lead Temperature for Soldering Purposes: 1/8″ from Case for 5 seconds (1) UL Recognized mounting method is per Figure 4. (2) Proper strike and creepage distance must be provided. SWITCHMODE is a trademark of Motorola, Inc. This document contains information on a new product. Specifications and information herein are subject to change without notice. Preferred devices are Motorola recommended choices for future use and best overall value. Rev 1 Device Rectifier Motorola, Inc. 1996 Data 1 MURF820 ELECTRICAL CHARACTERISTICS Characteristic Symbol Maximum Instantaneous Forward Voltage (3) (iF = 8.0 Amp, TC = 150°C) (iF = 8.0 Amp, TC = 25°C) vF Maximum Instantaneous Reverse Current (3) (Rated dc Voltage, TC = 150°C) (Rated dc Voltage, TC = 25°C) iR Maximum Reverse Recovery Time (IF = 1.0 Amp, di/dt = 50 Amp/µs) (IF = 0.5 Amp, iR = 1.0 Amp, IREC = 0.25 Amp) trr Max Unit Volts 0.895 0.975 µA 250 5.0 ns 35 25 i F , INSTANTANEOUS FORWARD CURRENT (AMPS) (3) Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤ 2.0%. 100 10 K 20 10 5.0 2.0 TJ = 25°C 1.0 100°C 0.3 0.1 0.2 1.0 K 400 100 40 10 TJ = 100°C 2.0 1.0 0.4 25°C 0.1 0.04 0.4 0.6 0.8 1.0 vF, INSTANTANEOUS VOLTAGE (VOLTS) Figure 1. Typical Forward Voltage 2 I R, REVERSE CURRENT ( µ A) 50 1.2 0.01 0 20 40 60 80 100 120 140 160 VR, REVERSE VOLTAGE (VOLTS) 180 200 Figure 2. Typical Reverse Leakage Current* Rectifier Device Data MURF820 TEST CONDITIONS FOR ISOLATION TESTS* CLIP MOUNTED FULLY ISOLATED PACKAGE CLIP MOUNTED FULLY ISOLATED PACKAGE LEADS HEATSINK 0.107″ MIN MOUNTED FULLY ISOLATED PACKAGE LEADS LEADS HEATSINK HEATSINK 0.107″ MIN 0.110″ MIN Figure 3. Clip Mounting Position for Isolation Test Number 1 Figure 4. Clip Mounting Position for Isolation Test Number 2 Figure 5. Screw Mounting Position for Isolation Test Number 3 * Measurement made between leads and heatsink with all leads shorted together. MOUNTING INFORMATION** 4–40 SCREW CLIP PLAIN WASHER HEATSINK COMPRESSION WASHER HEATSINK NUT 6a. Screw–Mounted 6b. Clip–Mounted Figure 6. Typical Mounting Techniques Laboratory tests on a limited number of samples indicate, when using the screw and compression washer mounting technique, a screw torque of 6 to 8 in . lbs is sufficient to provide maximum power dissipation capability. The compression washer helps to maintain a constant pressure on the package over time and during large temperature excursions. Destructive laboratory tests show that using a hex head 4–40 screw, without washers, and applying a torque in excess of 20 in . lbs will cause the plastic to crack around the mounting hole, resulting in a loss of isolation capability. Additional tests on slotted 4–40 screws indicate that the screw slot fails between 15 to 20 in . lbs without adversely affecting the package. However, in order to positively ensure the package integrity of the fully isolated device, Motorola does not recommend exceeding 10 in . lbs of mounting torque under any mounting conditions. **For more information about mounting power semiconductors see Application Note AN1040. Rectifier Device Data 3 MURF820 PACKAGE DIMENSIONS SEATING PLANE –T– –B– F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. C DIM A B C D F G H J K L N Q R S U S Q U A 1 2 3 H –Y– K G N L J R M B M MILLIMETERS MIN MAX 15.78 15.97 10.01 10.21 4.60 4.80 0.67 0.86 3.08 3.27 2.54 BSC 3.13 3.27 0.46 0.64 12.70 14.27 1.14 1.52 5.08 BSC 3.21 3.40 2.72 2.81 2.44 2.64 6.58 6.78 STYLE 1: PIN 1. CATHODE 2. N/A 3. ANODE D 2 PL 0.25 (0.010) INCHES MIN MAX 0.621 0.629 0.394 0.402 0.181 0.189 0.026 0.034 0.121 0.129 0.100 BSC 0.123 0.129 0.018 0.025 0.500 0.562 0.045 0.060 0.200 BSC 0.126 0.134 0.107 0.111 0.096 0.104 0.259 0.267 Y CASE 221E–01 ISSUE O Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1, Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488 Mfax: [email protected] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET: http://motorola.com/sps 4 ◊ MURF820/D Rectifier Device Data